Search Results

Search found 13075 results on 523 pages for 'bounding box'.

Page 159/523 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

  • LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

    - by CityView
    On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

    Read the article

  • dhcp3-server (dhcpd) is tampering with host NIC

    - by user61000
    Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

    Read the article

  • Using Computer name in URL causes issues when connecting to Web Services

    - by AWinters
    The set of applications I work on all access the same 8 or so web services that we have. These services and applications all reside on the same box and all use the computer name when trying to connect to the web service. For Example: If I have a web service called MapDataService and I have an application that accesses it, it would access it by the URL: http://COMPUTERNAME/MapDataService/MapDataService.asmx. This works in most of the applications that access the web service. However, we have several applications that, when using the computer name in the URL, will not get data returned from the service (actually a 503 is returned). In order to get it to work, the IP address of the system needs to be used in place of the COMPUTERNAME. This strikes me as very odd considering, as I mentioned before, all applications and services are on the same box and most other applications usr the COMPUTERNAME with no issues. Can someone give me some insight as to what could be causing this? We have no access to IIS logs and what logs we did get (this is on a customer site) are not very useful.

    Read the article

  • How do I stop linux from trying to mount android phone as usb storage?

    - by user1160711
    When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

    Read the article

  • Ubuntu 10.10 forgets desktop theme.

    - by Marcelo Cantos
    I am running Ubuntu in VirtualBox (on a Windows 7 host). Several times now, the top-level menu bar, the task bar — and seemingly every system dialog — have forgotten the out-of-the-box "Ambiance" theme they conform to when I first installed the system. Window captions still preserve the theme, but pretty much nothing else does. I have searched high and low on Google for assistance with this problem. Everything I've found suggests either running some gconf reset or deleting .gconf* .gnome* and other similar directories. I have followed all this advice and nothing works. I still get a boring Windows-95-style gray 3D look and feel. On previous occasions, after much messing around I've given up and rebooted the VM instance, and been pleasantly suprised to see the original "Ambience" theme restored throughout the UI, but invariably it disappears again some time later, usually after a reboot, so I can never figure out what I did that broke it. Here's a sample from Ubuntu's site of what I want it to look like. And here's a screenshot of my system as it currently looks. Also note that my GNOME Terminals normally have a nice purple semi-translucent look, and as can be seen from the screenshot, they are now just a solid matt white. This last time (just this morning), trying numerous combinations all the usual tricks and rebooting several times hasn't fixed it, so here I am on SU wondering: How do I recover the out-of-the-box theme for my Gnome/Ubuntu desktop, noting that blowing away all config files — as suggested in many places online — fails to achieve this? EDIT: It might help to know that it seems to fail either after I resize the VM instance, forcing the Ubuntu desktop to resize itself, or after I play around with Compiz settings. I haven't been able to figure out which of these it is, and it could be neither. Given the amount of pain I have had to go through to get things back to normal (and given that I am at a loss as to how to do so), it has proven difficult to definitively isolate the cause.

    Read the article

  • torrent downloads not showing on Squid log

    - by noobroot
    hello, i have just a few months working as sysadmin, hence i still have lots to learn, first thing id like to do is as follows: We have an OpenBSD 4.5 box acting like firewall,dns,cache etc, the box has 2 network cards, one conected directly to the internet and the other to our switch, i used to work with sarg for the log analysis but then changed to the much faster free-sa. I use a daily free-sa report to check the bandwidth usage and report our top 5 bandwidth consumers (3 days a week being #1 and you will be buying the pizzas :D, we are a small company ~20 so we are very familiar). this was working really good until recently, one of us required to download some stuff via torrent (~3GB) and since the pizza rule is active for non-work related downloads, he told me (verified) that his download was indeed work related so i would dismiss that 3GB off his quota, but to my surprise the log didnt showed that 3GB, since his ip consumption was only around 290MB. More recently, since the FIFA world cup started, we know that some of the employees are watching the match's streaming, we know it and we dont care about it since, like already stated, we are a small company so we dont have restrictive policies, we all can chat, watch youtube, download anything we want BUT we are only allowed 300MB a day otherwise you'll get in the top5-pizza-board, anyway, that streaming consumption is also not showing in the free-sa reports. So my question is, why is these data being excluded from the reports? im thinking that the free-sa reports list only certain types of things but im also thinking if are the squid logs the ones that are not erm... logging these conections. Any help, guide, advice or clarification is appreciated.

    Read the article

  • Windows Not Honoring DHCP Scope

    - by jerhinesmith
    Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

    Read the article

  • How can I install git on RHEL 6?

    - by JR.Xyza
    I'm trying to install Git on a RHEL6 development server, I have experience with Ubuntu but this is my first time working with RHEL (I'm a developer trying to fill in for a recently departed Linux Sysadmin). I've set up two additional repos (EPEL and IUS) for other packages needed for a Magento install. Output of yum repolist: [root@box]# yum repolist Loaded plugins: product-id, security, subscription-manager Updating certificate-based repositories. repo id repo name status epel Extra Packages for Enterprise Linux 6 - x86_64 7,841 ius IUS for RHEL 6Server - x86_64 135 Most of what I've read indicates a simple 'yum install git' should work with EPEL enabled, but I get the dreaded [root@box]# yum install git Loaded plugins: product-id, security, subscription-manager Updating certificate-based repositories. Setting up Install Process No package git available. Error: Nothing to do Same goes for git-daemon, etc. I've tracked down a number of git RPMs such as this one at repoforge but they require a train of dependencies that seems to never end. I've also toyed with compiling it manually but the rabbit hole to get make working seems to go even deeper. I'm convinced there's a simple oversight somewhere keeping me from being able to install from the EPEL repo, but I'm a rookie at all this. Thanks in advance for help/pointers/additional resources.

    Read the article

  • Can I autoregister my servers hostname in my local DNS? [on hold]

    - by Christian Wattengård
    We have evaluated a W2k12 server as a domain controller at work. This has the extra benefit of registering every "subordinate" computers name in it's DNS so that I don't have to go around remembering IP's all the time. (And it let's me easily run dhcp also on my "pop-up" dev-servers). We need to rework our work network for several odd reasons, and in this new scenario there was no money for an extra Windows 2012 license. We have at our disposal several old boxes that run linux quite well. Is it possible to set up a DNS-server-"appliance" that somehow autoregisters it's own hostname.. Scenario: Router (N66u) on 172.20.20.1. Runs DHCP on 172.20.20.100-200 range. Server [verdant] of a *nix flavor on 172.20.20.2 Laptop [speedy] of W8 flavor on DHCP assigned Laptop [canary] of W8 flavor on DHCP assigned Desktop [lianyu] of Ubuntu flavor on DHCP assigned What I would like is that all of the above servers (except possibly the router) would be available on verdant.starling.lan and canary.starling.lan and so on. This is how it works right now (except the Ubuntu box... I haven't cracked that one yet) because Windows just does this for you.. I would also be able to do this without any manual labor on the server. When I tell my box it's name is smoak it should "immediately" be available as smoak.starling.lan without any extra configuration on my part. How can I do this in a Linux (Ubuntu) environment?

    Read the article

  • What Device/System to use as a "router on a stick"

    - by Jeff Leyser
    I need to create several distinct VLANs, and provide a way for traffic to move between them. A "router on a stick" approach seems ideal: Internet | Router with Trunking Capability ("router on a stick") * * Trunk between router and switch * Switch with Trunking Capability | | | | | | | | | | | LAN 2 | LAN 4 | | 10.0.2.0/24 | 10.0.4.0/24 | | | | LAN 1 LAN 3 LAN 5 10.0.1.0/24 10.0.3.0/24 10.0.5.0/24 We have trunk-capable Layer-2 switches. The question is what to use as the router on a stick. My choices seem to be: 1) Use an existing Cisco 5505 ASA firewall. It appears the ASA can do the routing, but it's a 100Mbps device, and so seems sub-optimal at best 2) Buy a router. This seems overkill. 3) Buy a Layer-3 switch. Also seems overkill. 4) Use an existing Linux Box as a router 5) Use a new Linux box as a router' 6) Something I'm not thinking of I think either (4) or (5) is my best option, but I'm not sure how to choose between them. I expect the amount of traffic that has to cross the VLANs to be somewhat small, but bursty. How much load does routing add to a CentOS machine?

    Read the article

  • ssh works fine when using public interface, but slow when using private interface

    - by Kevin M
    My Linux(UbuntuEEE) to Linux(CentOS) ssh takes a long time to log in(~15 seconds) when using the private interface, but not when using the public one. I have a Linux box acting as my router. As such, it has multiple interfaces(75.xxx.xxx.xxx, 192.168.1.1). I can ssh in from the internal interface(192.168.1.65 to .1), but it will take a while. I can ssh into the public address, and it goes quickly(~1 second). I have another box that I can ssh into the inside interface from and it goes quickly. iptables is set to accept packets coming into the interface immediately. sshd's UseDNS is normally on; I get the same problem if I turn it off and restart sshd. I normally use public-key authentication; I have done a mv ~/.ssh/ ~/ssh/ and it will ask me for a password after going slowly. After logging in(using either interface), speed is quick. ssh client version(via ssh -v):OpenSSH_4.7p1 Debian-8ubuntu1.2, OpenSSL 0.9.8g 19 Oct 2007 ssh server version(via rpm -qv openssh_server):openssh-server-4.3p2-29.el5

    Read the article

  • OpenBSD pf - implementing the equivalent of an iptables DNAT

    - by chutz
    The IP address of an internal service is going to change. We have an OpenBSD access point (ssh + autpf rules) where clients connect and open a connection to the internal IP. To give us more time to reconfigure all clients to use the new IP address, I thought we can implement the equivalent of a DNAT on the authpf box. Basically, I want to write a rule similar to this iptables rule which lets me ping both $OLD_IP and $NEW_IP. iptables -t nat -A OUTPUT -d $OLD_IP -j DNAT --to-dest $NEW_IP Our version of OpenBSD is 4.7, but we can upgrade if necessary. If this DNAT is not possible we can probably do a NAT on a firewall along the way. The closest I was able to accomplish on a test box is: pass out on em1 inet proto icmp from any to 10.68.31.99 nat-to 10.68.31.247 Unfortunately, pfctl -s state tells me that nat-to translates the source IP, while I need to translate the destination. $ sudo pfctl -s state all icmp 10.68.31.247:7263 (10.68.30.199:13437) -> 10.68.31.99:8 0:0 I also found lots of mentions about rules that start with rdr and include the -> symbol to express the translation, but it looks like this syntax has been obsoleted in 4.7 and I cannot get anything similar to work. Attempts to implement a rdr fail with a complaint that /etc/pf.conf:20: rdr-to can only be used inbound

    Read the article

  • SSD as primary or secondary drive on a small Linux server?

    - by Alex Martelli
    I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

    Read the article

  • 'The rpc server is unavailable' or 'access is denied' error when using Remote desktop Services Manager on Windows 7 (but mstsc.exe works!)

    - by tbone
    I am trying to connect to a Windows XP workstation from a Windows 7 Ultimate workstation using Remote Desktop Services Manager. I am able to do a Remote Desktop (mstsc.exe) session from the Win7 machine to the WinXP machine with no problem at all. When running the Remote Desktops Admin (tsmmc.msc) too on a Windows XP box, I can also connect with no problem. However, when I use the new Remote Desktop Services Manager on Windows 7 and try to connect, I get the error: "The rpc server is unavailable" What could cause this? Has there been some fundamental change in Remote Desktop Services Manager, does it connect in a different way somehow? Update #1 Turned off firewall on the Windows XP box and the "The rpc server is unavailable" error went away; so RDSM seems to be using an entirely new port/connection/service compared to mstsc.exe or the old Remote Desktops Admin tool. Now... after disabling the firewall, I get a new error: Access is Denied. After doing some googling, I found some articles discussing this; basically, the error is very misleading - the actual problem is, if either side of the connection has dual monitors, and they are not both Win7 Ultimate, then you cannot connect using Remote Desktop Services Manager...the reason is, by default it uses the /multimon switch, and this switch requires a certain level of Windows license - and, there seems to be no way of changing this default (if anyone knows of a way to change this default, please post an answer or comment!). Nice going Microsoft. http://social.technet.microsoft.com/Forums/en-US/windowsserver2008r2rds/thread/4d06278f-e0f4-4f8e-a8e1-3697ee967ef4 http://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Windows/Windows_7/Q_26225743.html

    Read the article

  • Have servers behind OpenVPN subnet reach connecting clients

    - by imaginative
    I am trying to find some relevant documentation or what directives I need in either the OpenVPN server configuration or client configuration to accommodate for this use case. I have an OpenVPN server that clients connect to. The OpenVPN server can communicate directly with any of the clients already, this is not an issue. The client is able to reach any machine on the private subnet where OpenVPN resides, this is also not an issue. My issue is that the reverse is currently not possible - I have servers on the same subnet as the OpenVPN box that cannot reach any of the connecting clients. I'd like to be able to SSH to them and more, the same way the client can reach the servers behind the OpenVPN subnet. What do I need to do to make this possible? I already have masquerading rules set on the OpenVPN box: iptables -t nat -A POSTROUTING -s 192.168.50.0/24 -o eth0 -j MASQUERADE IP Forwarding is enabled: echo 1 >/proc/sys/net/ipv4/ip_forward I added a route on the server behind the private subnet to be aware of the route: 192.168.50.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 What am I missing?

    Read the article

  • Reading email from Emacs VM using a secure server (Gmail)

    - by Alan Wehmann
    This is a question (see below) originally entered at https://answers.launchpad.net/vm/+question/108267 and upon the recommendation of Uday Reddy the question and answers are being moved here. The date of the original question was May 4, 2010. One subject of the question is use of the program stunnel with program View Mail (run within Emacs) on a PC running Microsoft Windows, in order to read email from a server that requires use of TSL/SSL (Gmail). See the related question, How to configure Emacs smtp for secure server for using a secure server, for sending email. The programs discussed are Emacs, VM (ViewMail) and stunnel. The platform under discussion is MS Windows. The original question was asked by usr345 on 2010-04-24: I tried to install vm on Windows, but when I tried to get the mail from gmail using ssl, an error emerges, emacs hanges-up. Here is the code from .emacs: (add-to-list 'load-path (expand-file-name "~/vm/lisp")) (add-to-list 'Info-default-directory-list (expand-file-name "~/vm/info")) (require 'vm-autoloads) (setq vm-primary-inbox "~/mail/inbox.mbox") (setq vm-crash-box "~/mail/inbox.crash.mbox") (setq vm-spool-files `((,vm-primary-inbox "pop-ssl:pop.gmail.com:995:pass:usr345:PASSWORD" ,vm-crash-box))) (setq vm-stunnel-program "g:/program files/stunnel/stunnel.exe") So, the question: How to configure pop-ssl on Windows?

    Read the article

  • Nginx load balancing and maintaining URLs

    - by Steve Klabnik
    I'm trying to use nginx as a load balancer, and it's working great. One problem, though. The load balancing box is at 123.123.123.123, and the backend box is 456.456.456.456. So I have this config: upstream backend { server 456.456.456.456; } server { listen 80; server_name 123.123.123.123; access_log off; error_log off; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://backend; } } This works great. I hit 123.123.123.123 in my browser, and the page comes up. But now the URL in the browser says http://456.456.456.456. Do I need to use a rewrite rule or something to keep the url correct? I don't want it to be different when going to different backed servers. None of the tutorials I've read have mentioned anything about this.

    Read the article

  • ssh hangs on "Last login" line

    - by Pavel H
    This happened for the first time three days ago - I ssh to the server, authenticate using a password, get the welcome message but it remains hanging on the "Last login:..." line. The command line doesn't show and the server doesn't react to my input. Other services on the server keep working ok (apache, tomcat, database, ..). The box has an out-of-band management using which I was able to restart it. After the restart the ssh worked ok again and I didn't find anything suspicious in the logs. Three days later the same problem occurs on this box again, and newly on yet another server in the cluster - 100% same symptoms. Both servers have about 2 month old installation of Debian Squeeze (6.0.2) and the problem never occurred before despite frequent ssh-ing, so it should not be a problem of settings. We haven't been installing anything new for quite some time now. I also made sure there is enough disk space on both servers. Since it started to happen all of a sudden on two servers at about the same time, I suspect some bug may have been introduced via Debian updates, yet I haven't been able to find anyone with the same problem. Most similar issues I have found: ssh freezes at the "Last Login Line" - in our case everything worked fine until recently, so nothing related to settings should be our problem. Diskspace checked, I couldn't check the memory but I would expect something would be in the logs if the system had been running out of it. Remote Fedora system unresponsive, odd but consistent behavior when trying to log in - problem with high load on the server; unlike in this case, nothing changes even if I wait for 10+ minutes

    Read the article

  • Cant ping ip on LAN. Port forward works fine though.

    - by Anoop
    I have a Solaris 11 machine running inside the LAN. It is a default install. I can access the machine and ping it if I ssh into my router (if it matters, it is running dd-wrt). I cannot ping the Solaris machine using ip address from any other machine inside the LAN. But if I setup port forwarding everything works perfectly fine. I can also use the port forward from outside the LAN (from my office) - which is good and how I want it to be. I can SSH and ping and do pretty much everything else from outside as well as inside but only as long as I have the port forwarded from my router. Why would I not be able to ping or ssh or even access the Solaris 11 machine from within the LAN - I have checked and couldn't find any firewall running on the Solaris 11 box. I even tried disabling every known firewall on the router (dd-wrt, it had something like SPI firewall running). I even tried setting a static IP for my Solaris box but all in vain! Please help me understand how and why this happens!! Thanks.

    Read the article

  • How do I get rid of these "There is a problem with your tablet driver" messages?

    - by Adam Rosenfield
    Every time I run certain applications (including but not limited to GIMP, Microsoft Visual Studio, and 3DS Max), I get the following message box: There is a problem with your tablet driver. Please reboot your system. If the problem persists reinstall or update the driver. Obviously I've tried rebooting and that hasn't fixed anything. Secondly, I'm not running a tablet PC. This is just Windows XP SP3 running on a Dell Precision PWS490 desktop workstation. How do I get rid of these error messages? The applications still load normally after dismissing them, but they're rather annoying. Using Process Explorer, I got the call stack from the message box. It's coming from wintab32.dll. Here's the call stack when running GIMP (irrelevant frames omitted): ... 8 USER32.dll!MessageBoxA+0x45 9 wintab32.dll!WTMgrPacketHookExA+0x44a 10 libgdk-win32-2.0-0.dll!gdk_display_list_devices+0x37 ... So, does anyone know how I can get an updated version of wintab32.dll or have any other ideas? I've been keeping my system up to date with Windows Updates. The timestamp on wintab32.dll is 2007-03-30 17:38, and its MD5 sum is ffdc332007c9dc6dd346c8ac2b09a015.

    Read the article

  • Website hosted on my virtualbox web server not displaying images or applying css when viewed through phone

    - by WebweaverD
    I would really appreciate it if someone could help me. Please let me know if you need more info in the comments. My Set Up I have a windows 7 pc. On it I run a virtual box VM with a ubuntu 12 guest os and LAMP setup. I share files between the two machines using samba from linux to windows and using windows file sharing (Workgroup) the other way round. The vm is set up with a bridged network adapter and can happily serve web pages to my host machine. I use DHCP reservations on my home wireless router/modem to reserve an ip for the vm and give it a sitename.dev in my windows host file so I can access it at sitename.dev through the browser. The Problem So far so good but I have a dev project which needs a lot of mobile template development, now obviously I can use a browser plugin to simulate a mobile device but I would like to be able to see the real thing easily on my phone during development. So ideally I would like a similar setup on my iphone to my windows setup Now I'm not great on networking and dont have much experience with web server set up. So when I typed the ip of my virtual box into my iphone i wasnt expecting to see anything. I was pleasantly surprised when my site loaded up. The javascript even seems to be running but the images and css are not happening. My Question 1) What is happening here, is it something to do with the bridged set up on the vm network? 2)How do I make the sites load properly through my phone Notes I've also tried another phone. The same sites viewed on live servers work fine.

    Read the article

  • disk write cache buffer and separate power supply

    - by HugoRune
    Windows has a setting to turn off the write-cache buffer (see image) Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. Is it feasible and economical to get such a "separate power supply" for the internal sata drives of a non-server PC? Under what name is such a power supply sold? I know that there are UPS devices that can be connected to external drives,but what is required to be able to switch this setting safely on for an internal disk? The setting has different descriptions in different version of windows Windows XP: Enable write caching on the disk This setting enables write caching in Windows to improve disk performance, but a power outage or equipment failure might result in data loss or corruption. Windows Server 2003: Enable write caching on the disk Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows Vista: Enable advanced performance Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows 7 and 8: Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. This article by Raymond Chen has some more detailed information about what the setting does.

    Read the article

  • In Outlook 2007 Rules and Alerts, EXACTLY what does "my name" mean?

    - by Cornan The Iowan
    I can't find any definition of "my name" in the Outlook 2007 Rules and Alerts or on the Internet. In this case our email system presents two email addresses for me to the outside world. I'd like BOTH of these addresses to be recognized as being "me". I thought that perhaps if I understood the definition of "my name" in the rules, I could set up my mailbox(es) appropriately. Of course if "my name" actually means a single email address, then I won't be able to do so, but if it means "any email on my account" or "any account meeting [some criteria]", then I might be successful. I'd like to note a subtlety in the rules definitions. While there is a rule named "where my name is in the To or Cc box", the only rule for explicit addresses is "sent to people or distribution list" (I'm assuming that "sent to" means "in the To:" list rather than "in the To: or cc: lists"). Summing up. My preference: 1) Understanding the precise definition of "my name" so that I can use "where my name is in the To or Cc box" to capture both email addresses from my account. 2) Learning the "sent to people or distribution list" actually includes Cc: entries (I can test this myself of course) 3) Any other solution that will let me define a rule where my secondary email address will be detected in EITHER the To: or Cc: boxes.

    Read the article

  • Using Truecrypt to secure mySQL database, any pitfalls?

    - by Saul
    The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

    Read the article

  • Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

    - by DOTang
    I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

    Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >