Search Results

Search found 9688 results on 388 pages for 'external hdd'.

Page 159/388 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• On a failing hard drive, I am able to view data but unable to copy it - why?

  - by Tom

  I have a 2.5" external hard drive that is failing. It's not making the expected 'clicking' noise that most hard drives and I am able to view the data, but I am unable to actually retrieve the data. I attempted to use SpinRite in order to access the data on the drive, but it didn't like the external drive. When I view the drive's property page, the drive shows that it's used space is at 100% and that it has 0 bytes available; however, the progress indicator under the drive icon in Windows Explorer shows that it's roughly 50% full (which is correct). When I attempt to run Windows' "Error Checking" tool and attempt to "scan for an attempt recovery of bad sectors," the tool begins to run then immediately closes with no error message. I am able to browse the contents of the drive using Windows Explorer. When I begin to try copying any given single file, the copy process begins, an indicator starts, and then the copy fails with no real error message. The Disk Management page in Computer Management under Control Panel also shows this drive has being 'Healthy.' I dropped the drive off at a data recovery store and they said that "The data seems to be intact, but an internal failure is preventing any information from being retrieved." They offered to provide me references to a data recovery specialist. I've also attempted to run CHKDSK on the drive (with and without arguments) but it returns the following error: The type of the filesystem is RAW. CHKDSK is not available for RAW drives. Before going the route of more expensive data recovery, I'm wondering if these symptoms sound familiar to anyone? Other questions... I'm willing to continue trying tools such as TestDisk and/or PhotoRec (as the majority of the data that I'd like to salvage are photos) but how long I should expect either tool to run given approximately 400GB of data? I'm also comfortable using Linux so I welcome any suggestions for utilities or tools and strategies with which you've had success.

  Read the article

• Real-time local backup with versioning on Windows 7/8

  - by Borda

  I'm looking for a reliable backup solution on Windows, something with a feature set similar to Yadis. I've been using CrashPlan for 2 months, but their software lost more than 1TB of my data, that's why I'm looking for alternatives. Requirements: Real-time folder-to-folder backup: I don't need online features, I want to use this to duplicate my files between my local disks. Versioning support: Should be able to choose how many versions to keep of the files. Plain backup: I'd like to be able to open the backup without special software. No proprietary file format. External disk support: Shouldn't have any problem using external disks, at least on the source side. Backup every file, even locked/system files. (Yadis fails this one) Should start automatically, and have a comfortable GUI. Should use actively maintained and/or popular software. I don't want to use discontinued products. Optional requirements: Low RAM usage I'm not really comfortable with something that eats 1GB of my RAM. Compression support Preferably ZIP, but I'm not picky about this. Any ordinary everyday format is acceptable. Freeware or Open Source Preferred, but not necessary. I can do a one-time payment within reasonable bounds. (preferably under $100) I only need Windows support, but if it works on Linux, that's a plus. I've already searched and tried lots of software, most of them failed at the plain backup, the versioning or the locked file backup requirements.

  Read the article

• fax server farm architechture

  - by Brian Postow

  I'm not sure this is the right forum for this, but it's not Stackoverflow so... I'm trying to figure out an architecture to solve the following problem, maybe someone here can help: I have a T1 with 23 fax lines coming into the building. I have a computer (Macintosh XServe) running Hylafax. If I had one POTS line, I'd be done. However, I have no idea how to get the T1 into the Mac... Options I've considered: some sort of PCI T1-modem (Does that exist?) Splitting the T1 into 23 POTS lines and then connecting 23 analog modems to the mac, either via an external modem bank (Do they still make those?) or via some sort of external PCI bank, which will allow me to use more than 2 4-port modem cards. Either the T1 or the split POTS lines going into some intermediate device and then transfering the images over IP, or USB to the mac. Really, any other option I can come up with This has GOT to be a problem that someone has already solved, right?

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• PORT FORWARDING TO PUT MY WEB SERVER ON THE INTERNET

  - by Chadworthington

  I went to http://canyouseeme.org/ to check to see what my external IP address. Regardless of what port I enter, it tells me that the port is blocked. I have a LinkSys router that basically has the default settings with the exception that I have WEP encrptin setup and I have forwarded a few ports, including 80 and 69. I forwarded them to the 192.x.x.103 IP address of the PC which is running IIS. That PC runs Symantec Endpoint Protection, which I right mouse clicked in the tray to Disable. These steps used to make my PC visible so I could host my own web site in IIS on port 80, or some other port, like 69. Yet, the Open Port tool cannot see my IP when it checks eiether port and when I navigate to http://my external ip/ I get "page cant be displayed" At first I was thinking that maybe Comcast is blocking port 80, but 69 doesnt work eiether. I do not see any other blockking set up in my router and, as I mentioned, I went with teh defaults except where discussed. This is a corporate PC and Symantec End Point Protecion is new to it (this previously worked on teh same PC with Symantec Protection Agent), but I thought that disabling Sym End Pt from the tray, that that would effectively neutralize it. I do not have the rights to kill the program itself. Any suggestions on what else to try to make my PC externally visible?

  Read the article

• Slow transfer speed between two servers

  - by Linux Guy

  I have two servers both network cards speed is 10Gbps The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.1 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.1, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.0 port 38895 connected with 0.0.0.1 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service the connection will be ok , after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• Communicating via Command Mode with IBM HS22 IMM via AMM

  - by MikeyB

  On previous model blades that contained a BMC, I was able to communicate from our external management station via pass-through commands to the BMC to do things such as power blades on/off, set VPD parameters, reboot the BMC, etc. Now on the HS22, a bunch of things happen differently. For example, we can no longer use the same pass-through commands to write VPD information pages and have them persist across reboots of the IMM - it looks as though those VPD pages are populated from information contained in the IMM. How do we use the Advanced Settings Utility from an external host to communicate with HS22 IMMs? Alternatively, what TCP Command Mode commands do we need to send to the AMM to communicate with the IMM? For our purposes, we specifically cannot communicate with the IMM from the blade itself. Specific example: When I send a pass-thru IPMI command via the AMM to the blade BMC to write information (such as MTM, Serial) into VPD page 0x10, it persists on blades with a BMC (HS21 for example). I can send the same IPMI command to write data to the VPD page on the HS22, however it does not persist across reboots of the IMM. What IPMI commands do I need to send to the IMM? What IPMI commands are asu sending when it sets the MTM & Serial?

  Read the article

• Windows 8 & Hyper-V Can't Bridge Wifi Connection

  - by xinunix

  So I have an odd issue that I can't quite figure out... I am running Windows 8 Enterprise on a Dell 6420 laptop. I have a Broadcom 802.11n wireless adapter. I am connected to an home router (Netgear WNDR3700) that is connected to the internet. It is a very simple home network setup. I am trying to stand-up a few VMs in Hyper-V and want the VMs to be able to access the internet over my wireless connection. I have found numerous examples of how to set this up using both External and Internal Virtual Switches but have yet to be able to get it to work on my machine. I have narrowed the issue down to the fact that my host machine always loses internet connection when I bridge my wifi connection (both when it is bridged automatically by windows when I setup an external virtual switch bound to the wifi adapter or if I do it manually by creating an internal virtual switch, right click on it and my wifi network and select "Bridge Connections".) In both cases after the bridge is established, my host machine can no longer connect to the internet. I am not sure where to start with troubleshooting this problem. After the bridge is setup, an ipconfig shows all netowrk devices on the machine as "Media Disconnected". I do know that the wireless adapter is connected to the router b/c it shows the connection as active and full-strength. The only thing I can possibly think of is that this machine also has the Cisco VPN client installed on it which installs a Cisco Virtual Network Adapter. Is it possible that this Cisco Virtual Adapter is causing me issues when I try to bridge? I saw some people had a similar issue with a VirtualBox virtual adapter when trying to share via Hyper-V. Any thoughts or suggestions on how to troubleshoot?

  Read the article

• Fixing corrupt files or corrupt file table on a USB drive?

  - by Kelsey

  I was doing a virus scan on an external USB drive while copying data over to it. While AVG was scanning my system got locked up I think due to the USB drive running out of space and it required a reboot. Since that time all data on the external drive is no longer accessible. I can see all the files in the root and directories but I cannot browse into any of them as Windows 7 gives an error stating they are corrupt. I think the file table or whatever it uses to store the index of what exists on the drive has been corrupted since it still shows the the drive as being almost full but everything I do a properties check on says it is 0 bytes. Does anyone know how to 'unlock' or recover this data? Is there a way to rebuild the file table somehow? Luckily I can recover this data from other sources as a last resort but I would like to fix this if possible. Any help would be appreciated. Thanks.

  Read the article

• Configuring port forwarding for SSH - no response outside LAN [migrated]

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• check_snmp with snmpv3 protocol giving "Unkown Report message" error

  - by John

  I'm trying to add a nagios command to use snmpv3 for monitoring printer status messages. When using the check_snmp command, I get the following error: External command error: snmpget: Unknown Report message Here is the command I'm typing in: ./check_snmp -P 3 -H <hostname> -L authPriv -U snmpuser -A snmppassword -X snmppassword -o 1.3.6.1.4.1.11.2.4.3.1.2.0 -C public -d "STRING:" -a MD5 These values for auth key, private key, username, etc all work when using snmpwalk. Can someone enlighten me as to what that error message really means? EDIT: It looks like check_snmp isn't taking my v3 credentials when passing over to snmpget. Here is my input with the verbose option: ./check_snmp -H <hostname> -o 1.3.6.1.2.1.2.2.1.10.1 -C public -m ALL -P 3 -L authPriv -U snmpuser -a MD5 -A snmppassword -x DES -X snmppassword -v And here is the output: /usr/bin/snmpget -t 1 -r 5 -m ALL -v 3 [authpriv] <hostname>:161 1.3.6.1.2.1.2.2.1.10.1 External command error: snmpget: Unknown Report message So I guess now my question would be: why isn't check_snmp passing all the commandline options to snmpget?

  Read the article

• Configuring port forwarding for SSH - no response outside LAN

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• New router messed up server 2003 setup...

  - by Aceth

  Hey, We were sent a new 2wire router today configured it as best we can to match the old bt voyager. We've also got X static IP's. We've manage to get our webserver on one of the new IP's public facing. then we use a hardware firewall which is in a DMZ again with a different static IP. This firewall then is our gateway for our internal LAN. with a few servers etc. The problem we're having is only our PDC (primary Domain controller which has exchange 2003 on) can't ping externally even an external IP. We've connected laptops to the 2wire router and obtain a private ip 192.168.1.X and it works fine can ping etc. our other servers with an internal ip behind the firewall can ping out fine. We've connected to the firewalls logging console and the pings from the server are allowed through so its fine there. The server in question is a Windows server 2003 R2 Enterprise SP2 + Exchange 2003 Server doesn't have firewall turned on. it has static private IP .. gateway is pointing to the right one External Static IP is routing fine inwards We've ran out of ideas .. help??

  Read the article

• How do I get netcat to accept connections from outside the LAN?

  - by Chris

  I'm using netcat as a backend to shovel data back and forth for a program I'm making. I tested my program on the local network, and once it worked I thought it would be a matter of simply forwarding a port from my router to have my program work over the internet. Alas! This seems not to be the case. If I start netcat listening on port 6666 with: nc -vv -l -p 6666, then go to 127.0.0.1:6666 in a browser, as expected I see a HTTP GET request come through netcat (and my browser sits waiting in vain). If I go to my.external.ip.address:6666, however, nothing comes through at all and the browser displays 'could not connect to my.external.ip.address:6666'. I know that the port is correctly forwarded, as www.canyouseeme.org says port 6666 is open (and when netcat is not listening, that its closed). If I run netcat with -g my.adslmodem's.local.address to set the gateway address, I get the same behavior. Am I using this command line option correctly? Any insight as to what I'm doing wrong?

  Read the article

• Set up WLAN in 3-level house

  - by Balint Erdi

  I'm having a hard time setting up the network in our house. It has three levels (basement, ground floor, first level). The WLAN is set up by an ASUS RT-N12 router which provides perfect coverage for the ground floor and the basement. However, I set up my "home office" in the basement where the signal barely arrived. So I purchased a TP-Link TL-WA901ND (300 Mbps) Access Point which I set up in the other corner of the ground floor to expand the ASUS router's range. I used the AP's Repeater mode for that. The distance between my computer and the TP-Link AP is 6-7 meters. There is a staircase going down from the ground floor to the basement so there are no solid walls between the computer and the AP. This setup mostly works (I am writing this from the basement) but it is not reliable (the signal strength sometimes goes down to ~40% of the max) sometimes so I wonder if I am doing it correctly or if there is a better way. Screenshot of the router's and the AP's dashboard screen follow: Any comments on what I am doing wrong or hints for improvement are appreciated. Thank you. UPDATE Tried one more thing, setting up the TP-LINK AP in Access Point mode. That way, I can make it use a different SSID. I enabled WDS/Bridge so that it expands the range of the ASUS router (see screenshot). That does not work, either, if I connect to the network set up by the TP-LINK device (PELSTER-2), I can't reach the external network (the Internet). It seems the problem always comes back to this, the TP-LINK does not have access to the external network, whatever its mode of operation.

  Read the article

• Server 2008 NAT Internet Not Working

  - by Jack

  I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

  Read the article

• Robocopy launches and then hangs/just sits there

  - by NateO

  I'm setting up an archive process to store old files on an external hard drive. The computer in question is running Windows 7 Pro 32bit. We have a server folder with 150,000+ files in it, most of which are pretty small (below 200k). I'm trying to use robocopy in a batch file to do this. It was working fine the other day, now all it does upon launch is sit there. It shows me all the options and whatnot, and also lists the number of files in the directory and the directory itself, but it never gets past that line. If I switch the destination to the local C drive, it eventually starts copying files. Is there something in my batch file that needs to change? Or could there be a problem with the external Western Digital drive that I'm using? The WD drive currently is holding about 175,000 files. Here is the one line batch file I have: robocopy "\\cgifp01\Prepress\Public\ImportedPDF" "E:\OldFiles" *.* /R:2 /W:10 /MINAGE:15 /MOV /B /XJ /XF "blank_test.pdf" Thanks for any tips or ideas. Nate

  Read the article

• Windows 7 Can't Connect to Network Drive on Windows XP

  - by Alex Yan

  I have a Windows XP desktop and a Windows 7 laptop both connected to a TrendNET TEW-432BRP router, which is connected to the Internet. They both have static IPs. The desktop has an external hard drive connected to it. The laptop is wireless and the desktop is wired. I enabled sharing on the external hard drive about two years ago when I bought it. I mapped it as a network drive on the laptop. I think it was yesterday, the laptop just stopped recognizing any of the computers on my network (When I open network, my laptop's the only one on it). I also get an error message "An error occurred while connecting A: to \CERTIFIED-DATA\Expansion Microsoft Windows Network: The network path was not found. The connection has not been restored" when I try to connect to the network drive. Both computers run Avast, and there hasn't been any problems with it. This has happened before but I never figured out why and how to fix it. It's usually fixed when I reinstall the OS of the affected system. Edit: I can't navigate the computer using \\CERTIFIED-DATA. I get a message saying "Windows cannot access \CERTIFIED-DATA. Check the spelling of the name, Otherwise, there might be a problem with your network" I clicked diagnose on the message and it failed to find anything wrong I clicked diagnose on my wireless connection, and it just keeps trying to check if something is wrong with the connection I can ping it successfully

  Read the article

• Apache Reverse proxy for intranet and other integrated application on intranet

  - by user1433448

  I'm trying to configure a reverse proxy (ssl) with apache 2.2 in Debian Squeeze, but I have some problems, specially with some path absolute and with https I'll try to detail what I have made and what I'm trying to configure I have a server Debian Squeeze with apache2.2 + mod_proxy_html with: # apt-get install libapache2-mod-proxy-html libxml2-dev # a2enmod proxy # a2enmod proxy_http # a2enmod proxy_html # a2enmod headers After that I have configured a virtual host with: reverse_proxy_ssl.conf I'm trying to configure to allow access of our intranet from internet with a reverse proxy (apache that is located in DMZ). With this configuration domain.com/intranet works correctly and we can access to intranet, but we have one problem when from domain.com/intranet we need to use another internal application that is called from intranet with absolute path ( https://192.168.10.25/application/) and from internet appears that try to access with internal ip, and this link es incorrect from external site We only need to access from intranet to multiple internal application that are in external server and we like to restrict to minimal access from internet. All the application that are in the smae server of intranet are working. The second problem is with https and reverse proxy in our firewall appears some errors with packets (not valid packets), and with https seems to work. What can I do to solve this problems (absolute path and ssl problem) Thanks

  Read the article

• SharePoint Business Connectivity Services (BCS) Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'

  - by g18c

  I am running SharePoint 2010 with SQL 2012, I am trying to get Business Connectivity Services (BCS) running but I am facing a double-hope authentication issue. Everytime I try to connect to the external BCS list created in SharePoint designer, I get the error Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. In the event viewer on the SQL server I see a login failure for an anonymous user from the SP server IP address. Background information below: I have enabled Kerberos under SharePoint Central admin. I have the following AD domain accounts: SP_Farm - main website pool SP_Services - for SharePoint services (including BCS) SQL_Engine - SQL database engine I then created the following with SetSPN: SetSPN -S http/intranet mydomain\SP_Farm SetSPN -S http/intranet.mydomain.local mydomain\SP_Farm SetSPN -S SPSvc/SPS mydomain\SP_Farm SetSPN -S MSSQLSvc/SQL1 mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1.mydomain.local mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1:1433 mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1.mydomain.local:1433 mydomain\SQL_DatabaseEngine I then delegated the AD accounts for any authentication protocol to the following: SP_Farm - SP_Farm (http service type, intranet) SP_Farm - SQL_DatabaseEngine (MSSQLSvc, sql1) SP_Service - SP_Service (SPSvc) SP_Service - SQL_DatabaseEngine (MSSQLSvc, sql1) I have also checked the WFE is being logged on to with Kerberos, with the WFE server event log showing event ID 4624 with Kerberos authentication, this is OK. The SQL is also showing connections authenticated as Kerberos from the WFE with the following query: Select s.session_id, s.login_name, s.host_name, c.auth_scheme from sys.dm_exec_connections c inner join sys.dm_exec_sessions s on c.session_id = s.session_id Despite the above, credentials are not passed from the client through the SharePoint server to the SQL server, only the anonymous account is used. I get the following error in the WFE server for 'BusinessData' ID 8080: Could not open connection using 'data source=sql1.mydomain.local;initial catalog=MSCRM;integrated security=SSPI;pooling=true;persist security info=false' in App Domain '/LM/W3SVC/1848937658/ROOT-1-129922939694071446'. The full exception text is: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. If I set a username and password with the Secure Store Service and set the external list to use the impersonated credentials, the list works. Any ideas what I have missed and what can be tried next?

  Read the article

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• Problem hosting server behing personal router

  - by Venkatesh Hodavdekar

  I recently bought the domain name lucidcontraptions.com and want to host the website from home. I have a D-Link router in which I have set up my personal virtual server correctly. My application server is Apache 2.2. The server works perfectly with the following settings: External IP: 207.172.xx.xx. Public port: 8888 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx:8888/ the server works perfectly and my Apache page shows up without any issues, both from inside the intranet as well as outside. This setting would not work out for me as I am not allowed port numbers in my DNS management. Now when I tweak the settings to the following: External IP: 207.172.xx.xx. Public port: 80 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx/ the server works perfectly and my Apache page shows up without any issues, BUT ONLY FROM INSIDE THE INTRANET. This page does not show up for people outside the intranet.

  Read the article

• Do registry issues with Win7 persist through a recovery from a system image?

  - by user59089

  So I need a bit of advice, please; here's my situation: I have 1) a system image on an a brand new external 1 TB SATA drive, that I managed to successfully capture before my 2) primary system drive went down. I realize this is a fairly simple matter of buying a new primary drive and performing the recovery to the fresh disk...however, the issue is that I believe Win7 was also having some significant issues of its own--basically, Update unable to install updates, and Backup continually ditching the auto backup schedule. I'd been trying to address those issues when my system was still working, but it's been so fruitless, I'm convinced a Win7 re-install would be best, and now I'm concerned that if I was in fact having what I believe are likely registry-related issues before, that these will persist through a recovery--would that likely be correct? I'm mainly worried about recovering my files, so if I did a full recovery from the image, should I be able to then access my individual files, and copy them manually to an external drive, so I can then do a full re-install of Win7? Sory if this seems obvious, but I've never done a recovery before and just trying to make sure there's no red flags with what I have in mind...

  Read the article

• Webmin ADSL module

  - by expatcm

  I was wondering if the Webmin ADSL module is going to help me solve a problem .... but I cannot find any documentation telling me what the module does ..... Any ideas? What I am hoping is that it will solve a problem .... I am just in the process of setting up a Debian server. I will use the DHCP server as part of the Debian setup to manage the lan IP addresses. I want to turn off the external DHCP server which is part of the Linksys ADSL modem / router and use just the modem. The challenge I have is knowing what I need to do in order to get the public DNS on the eth1. When I turn off the DHCP on the modem / router not a lot happens apart from no longer being able to access the settings .......... So I am looking at this Webmin module and wondering if it is to manage the ADSL connection and find the public DNS address .... The local DHCP server is working well for the lan, I am just stuck for the external DNS.

  Read the article

• Static noise in headphones

  - by John Murdoch

  I have a Asus P6T based system. I was using the on-board sound (plugging in Logitech X-230 2.1 analog speakers in the green "front speakers" 3.5mm analog output, then plugging in my headphones in that). I was quite happy with the sound quality (didn't hear any static noise if volume was turned down to my normal listening level). Then about a week ago I started having terrible static noise from the left channel, and no normal audio on that left channel. Right channel had more static noise than usual but did have a bit of sound. I tried using the AC'97 in front of my case but that seemed to have no signal. I decided my on-board sound card has gone bad and bought an internal sound card to replace it (Startech 7.1Ch PCI). This fixed the "no sound from left channel problem", but I had much more audible static noise. I decided the card was low quality and/or it had interference from all the other things happening inside the computer case, and bought a Sweex SC016 external USB sound card. But even with that I have static noise in headphones. Positioning the USB sound card differently doesn't seem to help. Trying the other analog outputs (e.g., surround) doesn't help. The static noise in all cases is proportional to the volume. I have tried different headphones, but the situation is situation though perhaps the flavour of the static noise changes slightly. So what are my options? a) Get another, more expensive, external USB sound card hoping the quality will improve? b) Get another, more expensive, internal sound card (PCIe 1x perhaps) hoping the quality will improve? c) Get a dedicated DAC box? d) Get some Hi-Fi earphones? Suggestions? tl;dr - Two different sound cards both still have static noise in headphones.

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >