Search Results

Search found 1662 results on 67 pages for 'cisco ace'.

Page 16/67 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

• Why DELL PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

  - by Kedare

  Hello ! I have a little question, I'm actually studing IT in France, and when looking on alternative on the very [...] very expensive Cisco equipments, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipments in France :( Thank you !

  Read the article

• Cisco, CA Expand UCS for Better Data Center Management

  Expansion of a technology agreement between CA and Cisco may benefit Cisco UCS users with better data center management for both applications and networks.

  Read the article

• Cisco 877 as PPPoA/PPPoE bridge (no routing) - how to make it listen to IP for management?

  - by Ingmar Hupp

  I have a Cisco 877 configured to bridge ADSL with PPPoA to PPPoE on Vlan1. This works fine, but in this mode the only way I can configure the Cisco is via the serial console. I'd like to have the Cisco also listen on an IP address so I can telnet/ssh into it. I think the right way to go about this would be via bridge irb, but I'm not sure exactly how (or if that's even the right direction). IOS is 12.4T and my current config (cut down to essentials) is: no ip routing no ip cef ! ! interface ATM0 no ip address no ip route-cache no atm ilmi-keepalive pvc 0/38 encapsulation aal5snap ! dsl operating-mode auto bridge-group 1 ! ! interface Vlan1 no ip address no ip route-cache bridge-group 1 Just setting an IP address on Vlan1 didn't have the desired effect, but surely this must be possible somehow (the Draytek Vigor 120 even does it by default).

  Read the article

• Why PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

  - by Kedare

  Hello ! I have a little question, I'm actually studing in IT in France, and when looking on alternative on the very [...] very expensive Cisco equipment, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipment in France :( Thank you !

  Read the article

• Is it possible to repair a Cisco 3500 XL (3548) switch with POST Error messages?

  - by Alex

  I've got an old Cisco 3500 XL, and it seems to have hardware issues. I've loaded the latest IOS and cleared all config. Does anyone have any experience fixing the switch core? I'm a reasonably competent SMD solderer, can I replace/reflow some chips? I've checked the power supply voltages and it's all within tolerance, and no visible signs of any component damage. Some chips are hot to the touch. I understand that these were EOL as of 2007, but should have a lifetime warranty for the electronics. I don't have a Cisco support contract, so I can't file a ticket. What should I do? Console output: switch: dir flash: Directory of flash:/ 2 -rwx 1811584 <date> c3500xl-c3h2s-mz.120-5.WC17.bin 1799680 bytes available (1812992 bytes used) switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"...################################################################################################################################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC17.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Tue 13-Feb-07 15:04 by antonino Image text-base: 0x00003000, data-base: 0x00352924 Initializing C3500XL flash... flashfs[1]: 1 files, 1 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 3612672 flashfs[1]: Bytes used: 1812992 flashfs[1]: Bytes available: 1799680 flashfs[1]: flashfs fsck took 3 seconds. flashfs[1]: Initialization complete. ...done Initializing C3500XL flash. C3500XL POST: System Board Test: Passed C3500XL POST: Daughter Card Test: Passed C3500XL POST: CPU Buffer Test: Passed C3500XL POST: CPU Notify RAM Test: Passed C3500XL POST: CPU Interface Test: Passed C3500XL POST: Testing Switch Core: Passed Error with Switch Core BIST test Phase 0. Returns: Test Complete Low : 0x0FFFFFFF, Test Complete High : 0xFFFFFFFE Test Phase Low : 0x00000040, Test Phase High : 0x00000000 Test Phase Third : 0x00000000, Test Complete Third : 0x000001F8 C3500XL POST FAILURE: Testing Switch Core: Failed C3500XL POST FAILURE: Testing Buffer Table: Failed C3500XL POST FAILURE: Data Buffer Test: Failed C3500XL POST FAILURE: Configuring Switch Parameters: Failed C3500XL POST FAILURE: Switch Core BIST failed. C3500XL POST FAILURE: Cannot test Modules due to failure of Switch Core POST Del Mar Failure (0th Del Mar): req system failed to init C3500XL POST FAILURE: C3500XL POST FAILURE: ATM: required system failed to init C3500XL POST: Ethernet Controller Test: Passed C3500XL POST FAILURE: MII Test: Failed C3500XL POST FAILURE: Error waiting for Ethernet Controller and SW_PARAMS C3500XL POST FAILURE: Initialization/POST failed C3500XL POST FAILURE: AT: Failing because system POST failed Exception (8192)! Debug Exception (Could be NULL pointer dereference) CPU Register Context: Vector = 0x00002000 PC = 0x000F36F4 MSR = 0x00029200 CR = 0x22000024 LR = 0x000F6964 CTR = 0x001DE46C XER = 0x00000000 R0 = 0x00000000 R1 = 0x004E2580 R2 = 0x00000000 R3 = 0x00000000 R4 = 0x00000001 R5 = 0x00000000 R6 = 0x004E2718 R7 = 0x004E2718 R8 = 0x00000008 R9 = 0x00000000 R10 = 0x0000FFFF R11 = 0x00480000 R12 = 0x42000024 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000 R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000 R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000 R24 = 0x00000000 R25 = 0x00000020 R26 = 0x004E2718 R27 = 0x004E2718 R28 = 0x00000020 R29 = 0x00002513 R30 = 0x00000001 R31 = 0x00000000 Stack trace: PC = 0x000F36F4, SP = 0x004E2580 Frame 00: SP = 0x004E25A0 PC = 0x40000016 Frame 01: SP = 0x004E2618 PC = 0x000F6964 Frame 02: SP = 0x004E26A8 PC = 0x000F76DC Frame 03: SP = 0x004E26C8 PC = 0x000E8114 Frame 04: SP = 0x004E26F0 PC = 0x001F5BF8 Frame 05: SP = 0x004E2710 PC = 0x001F5CF4 Frame 06: SP = 0x004E2748 PC = 0x0023F4DC Frame 07: SP = 0x004E2750 PC = 0x0023E650 Frame 08: SP = 0x004E27C8 PC = 0x0023E89C Frame 09: SP = 0x004E27E0 PC = 0x0028AF34 Frame 10: SP = 0x004E27E8 PC = 0x001E38F8 Frame 11: SP = 0x004E2808 PC = 0x001E39A8 Frame 12: SP = 0x004E2820 PC = 0x0014E220 Frame 13: SP = 0x004E28C8 PC = 0x0014E39C Frame 14: SP = 0x00000000 PC = 0x001EB510

  Read the article

• Missing AnyConnect libxml2.so.2

  - by Hypercube

  I'm trying to install Cisco AnyConnect VPN Client on Maverick 64-bit. I'm getting the following errors: Installing Cisco AnyConnect VPN Client ... Removing previous installation... /opt/cisco/vpn/bin/manifesttool: error while loading shared libraries: libxml2.so.2: cannot open shared object file: No such file or directory vpnagentd: no process found Extracting installation files to /tmp/vpn.Mjh9Z5/vpninst086037244.tgz... Unarchiving installation files to /tmp/vpn.Mjh9Z5... Starting the VPN agent... /opt/cisco/vpn/bin/vpnagentd: error while loading shared libraries: libxml2.so.2: cannot open shared object file: No such file or directory I have libxml2.so.2 in /usr/lib, though. Should it be somewhere else? Thanks in advance.

  Read the article

• How to setup a static multicast ARP entry with Cisco SG300?

  - by Fredrik Hedberg

  We're running a Microsoft NLB cluster in multicast mode as a loadbalancer. Using our old Cisco IOS switches we propagate access to the cluster to our branches using a static ARP entry in the core router: arp 10.20.1.226 03bf.0a14.01e2 ARPA But how does one solve this using non-IOS based Cisco hardware such as the SG300 series? Adding a static ARP entry results in an error message telling the user that the hardware address needs to be a valid unicast MAC address.

  Read the article

• Can PPP CHAP authentication use Cisco "Type 5" MD5 passwords?

  - by romandas

  Looking over Cisco's documentation, and RFC 1994 (PPP CHAP authentication), my initial guess is "no", because CHAP requires a cleartext password to rehash every time it sends a challenge. Is this true? If so, is there another way to configure CHAP so it doesn't use the easily-decoded type 7 passwords? The Cisco device in question uses local authentication, not a TACACS+ or RADIUS server. Would using RADIUS eliminate the problem or just move it to the RADIUS server?

  Read the article

• How to redirect Cisco IOS's show output to HTTP URL?

  - by yegle

  I found there's a redirect output modifier of Cisco IOS ( version 12.2(53)SE1 ), and there's http: URI support: #sh version | redirect ? flash: Uniform Resource Locator ftp: Uniform Resource Locator http: Uniform Resource Locator https: Uniform Resource Locator nvram: Uniform Resource Locator rcp: Uniform Resource Locator scp: Uniform Resource Locator tftp: Uniform Resource Locator However, I cannot find any document on cisco.com about the http support. I tried sh version | redirect http://my_server/ and cannot find any information on my_server's access log. Can anyone give me a hint?

  Read the article

• How to ace Skype Interviews

  - by FelixWehmeyer

  Many companies these days opt to include a Skype interview in the recruitment process, as it comes close to a face-to-face interview without the time and costs involved for both the company and the candidate. In some cases during the recruitment process at Oracle you also might be asked to conduct a Skype interview. To help you get started with this, we researched some websites to give you several tips and tricks. What most of the bloggers say about this topic is collected in this article to help you prepare. It is all about Technology The bit that can make a Skype interview more complicated than a face-to-face or phone interview is the fact you are using additional technology. Always check the video and audio capabilities of your computer to make sure they work properly. Be prepared for connections to be limited during the interview. Using a webcam can also be confusing, if you do not have a lot of experience using it. Make sure you look at the camera and not the monitor to avoid the impression you are looking away. Practice If you do not feel comfortable using the camera, do a mock interview with a friend or family member before you have the actual interview. Be aware that facial impressions or reactions come across differently on a monitor, so make sure to practice how you  come across during the interview. Good lighting in the room also helps you make you look the best for the interviewer. You and your room Dress code, as in any face-to-face interview,is important to think about. Dress the same way as you would for face-to-face interviews and avoid patterns or informal clothing. Another tip,is to be aware of your surroundings. Make sure the room you use looks good on camera, making sure it is neat and tidy, also think about how the walls look behind you. Also make sure you do not get distracted during the interview by anyone or anything, as this will directly have an impact on your interview and your ability to focus and concentrate. What is in a name What goes for any account that you share during the recruitment process, either your email address or Skype name, is to make sure it comes across as professional. Try to avoid using nicknames or strange words in your accounts, stick to using a first name – last name or an abbreviation of the same. If you would like to read more about this topic, have a look at the links below which we used as inspiration for this blog article. 7 Deadly Skype Interview Sins is fun to read and to gives you some good advice to keep in mind. ·         http://www.inc.com/guides/201103/4-tips-for-conducting-a-job-interview-using-skype.html ·         http://blog.simplyhired.com/2012/05/5-tips-to-a-great-skype-interview.html ·         http://www.cnn.com/2011/LIVING/07/11/skype.interview.tips.cb/index.html http://www.ehow.com/how_5648281_prepare-skype-interview.html

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• What characters are illegal in Cisco IOS username secret passwords?

  - by Alain O'Dea

  I am using username secret to add users with encrypted passwords to our switches and firewall. I have been battling with the same switches and firewall for a couple of hours trying to get securely generated hard passwords for all admins. Sometimes, the passwords would go into config, but wouldn't work for login. According to the documentation for enable secret a password must not begin with a number and ? has to be entered as Ctrl-V then ? to escape it. I followed that and still got passwords I could not use sometimes. There was no error when I ran username, but the password would be rejected on login by some, but not all of the switches. They are all WS-C2960-48PST-L. The passwords it didn't like contained back ticks "`" (that character under tilde ~ under Esc). The "misbehaving" switches are running: Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5, RELEASE SOFTWARE (fc1) The "working" switches are running: Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(46)SE, RELEASE SOFTWARE (fc2). The "misbehaving" switches are running a newer IOS, so this suggests a regression introduced somewhere between 12.2(46)SE and 12.2(50)SE5. I was unable to find any evidence of this being intentional in the release notes for 12.2(50)SE. I would like to avoid this next time the passwords are changed :) What characters are illegal in Cisco IOS username secret passwords? Thank you for your help :)

  Read the article

• How to bridge Debian guest VM to VPN via Cisco AnyConnect Client running on Windows Vista host

  - by bgoodr

  I am running Cisco Anyconnect VPN Client version 2.5.3054 on a laptop running Windows Vista Home Premium (version 6.0.6002) Service Pack 2. I am running the VMware Player version 4.0.2 build-591240. The host operating system running under VMware Player is Debian 6.0.2.1 i386. The laptop is connected to a wireless connection, and I can browse the web from Windows Vista using Firefox just fine. I am able to boot into the Debian VM and open up a browser and access websites on the WAN from within the VM just fine. I can ping real Linux hosts on my LAN via: ping <lan_system>.local where <lan_system> is the hostname returned from uname -a on that system on my LAN. From a DOS CMD shell, I am able to ping hosts that exist on the remote network served by the Cisco AnyConnect Client's VPN network (and without the .local suffix applied as above): ping <remote_system> However, from within the Debian VM, I expect to be able to also ping those same remote hosts (<remote_system>) that are tunnelled over the VPN set up by Cisco AnyConnect Client. Let's say that I can ping a <remote_system> called flubber from a DOS CMD prompt just fine. When I execute Linux ping command from inside the Debian VM via: ping flubber It returns immediately with this output: ping: unknown host flubber For reference since I suspect it will be useful, here is the output of the route print command from the DOS CMD prompt: route print =========================================================================== Interface List 30 ...00 05 9a 3c 7a 00 ...... Cisco AnyConnect VPN Virtual Miniport Adapter for Windows 11 ...00 1b 9e c4 de e5 ...... Atheros AR5007EG Wireless Network Adapter 26 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 28 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 1 ........................... Software Loopback Interface 1 12 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 13 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 32 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #4 27 ...00 00 00 00 00 00 00 e0 isatap.{E5292CF6-4FBB-4320-806D-A6B366769255} 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 20 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #8 22 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #10 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #11 25 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #12 29 ...00 00 00 00 00 00 00 e0 isatap.{C3852986-5053-4E2E-BE60-52EA2FCF5899} 41 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #14 =========================================================================== At the top window border of the VM, clicking on Virtual Machine, then clicking on Virtual Machine Settings, then clicking on Network Adapter, I have these two options checked: [X] Bridged: Connected directly to the physical Network [X] Replicate physical network connection state [ ] NAT: used to share the hosts's IP address [ ] Host-only: A private network shared with the host [ ] LAN segment: [ ] <LAN Segments...> <Advanced> I've toyed with the other options such as NAT and Host-only but that had no effect. Is there some way to allow the VM to access those <remote_system>'s?

  Read the article

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• Cisco CCENT Exam

  - by freddy6

  Hi All, I am due to sit my CCENT exam in about 3 weeks, for anyone who has sat the exam recently or knows about the exam: How many questions is in the exam How long does the exam go for Will there be a lot of question based on the CLI commands?

  Read the article

• Cisco ASA log error "regular translation creation failed for icmp ..."

  - by Martijn Heemels

  Every few seconds our new Cisco ASA 5505 firewall is logging errors that I can't figure out with my limited Cisco experience. Severity Date Time Syslog ID Source IP Destination IP Description 3 Mar 25 2010 17:21:14 305006 8.8.8.8 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.8.8 (type 3, code 3) 3 Mar 25 2010 17:18:37 305006 8.8.4.4 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.4.4 (type 3, code 3) The logged inside IP is our internal DNS resolver, and the outside IP's are Google's public DNS servers. ICMP Type 3 Code 3 means "Port Unreachable" Our "outside" interface has a fixed IP and our "inside" interface is in the 10.10.0.0/16 subnet. The 'Inspect DNS' Service Policy is enabled, with the preset DNS inspection map. Furthermore there's an ACL that allows all inbound ICMP on the "outside" interface. I've spent hours trying to figure this one out, so any and all advice is welcome!

  Read the article

• Can't figure out error in Cisco ASA log "regular translation creation failed for icmp ..."

  - by Martijn Heemels

  Every few seconds our new Cisco ASA 5505 firewall is logging errors that I can't figure out with my limited Cisco experience. Severity Date Time Syslog ID Source IP Destination IP Description 3 Mar 25 2010 17:21:14 305006 8.8.8.8 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.8.8 (type 3, code 3) 3 Mar 25 2010 17:18:37 305006 8.8.4.4 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.4.4 (type 3, code 3) The logged inside IP is our internal DNS resolver, and the outside IP's are Google's public DNS servers. ICMP Type 3 Code 3 means "Port Unreachable" Our "outside" interface has a fixed IP and our "inside" interface is in the 10.10.0.0/16 subnet. The 'Inspect DNS' Service Policy is enabled, with the preset DNS inspection map. Furthermore there's an ACL that allows all inbound ICMP on the "outside" interface. I've spent hours trying to figure this one out, so any and all advice is welcome!

  Read the article

• How do I use Cisco WebEx Connect IM on Mac OS X?

  - by overboming

  How do I use Cisco WebEx Connect IM on Mac OS X, it seems to be using Jabber protocol.

  Read the article

• How do I combine static and dynamic DHCP leases on a Cisco router?

  - by Brad

  Basically, what I need is super similar to the unanswered cisco forum question below: https://supportforums.cisco.com/message/3139749#3139749 I have a Cisco 850 Series router. I have configured a DHCP pool for the 10.0.0.0/24 network. I have excluded 10.0.0.1 - 10.0.0.99 from the DHCP pool. I want to add a static DHCP pool for stuff and I want DHCP to statically assign them the addresses of my choice below 100. Actually, I don't care what addresses I statically assign. They can be anything in the pool for all I care, I just want it to work. Why are you doing this? Just statically assign the IPs on the devices! I don't want to do this because I have some laptop users. They could obviously only use that static IP here. This isn't a problem if they could be bothered to change any location setting or something. They can't. So it HAS to be DHCP. It also has to be static IPs because I need to forward ports to them. I know, I know, this is weird but it's an apartment LAN/WLAN so this isn't exactly a typical use case. Relevant sections of config below: ip dhcp excluded-address 10.0.0.1 10.0.0.99 ! ip dhcp pool Internal-net import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.1 domain-name 1770.local lease 7 ! ip dhcp pool static-pool import all origin file flash://staticmap default-router 10.0.0.1 domain-name 1770.local Contents of staticmap: *time* Aug 5 2010 09:00 AM *version* 2 !IP address Type Hardware address Lease expiration 10.0.0.100/24 1 001f.5b3e.d50a Infinite *end* You can see here I was trying addresses outside the excluded-address range to see if that would make any difference. My testing machine's MAC: mainframe:~ brad$ ifconfig en1 en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:1f:5b:3e:d5:0a What shows up in the DHCP binding table: basestar#show ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 10.0.0.112 0100.1f5b.3ed5.0a Aug 12 2010 10:06 AM Automatic What's up with the funny looking MAC in the DHCP binding table?? Is what I'm trying to accomplish basically impossible? Am I going about this the wrong way? All I want to to be able to port forward some ports to specific devices. The way I would do this with a consumer router is to do what I'm trying to do here; assign static DHCP to those devices then configure PAT for ports on those addresses.

  Read the article

• How to integrate Windows Server 2008 R2's NPS with Cisco switches?

  - by Massimo

  I need to evaluate in a lab environment the use of Windows Server 2008 R2's NPS for 802.1x authentication with Cisco Catalyst 3750 switches; the general idea is to only let clients connect to the company network if they can provide valid domain logon credentials, placing them in a restricted VLAN instead if they can't. NAP would also be a bonus, but it can be evaluated later; the main point now is only 802.1x authentication. Although I have very good knowledge of Windows and Active Directory (on the Microsoft side) and quite good knowledge of Catalyst switches (on the Cisco side), I'm totally new to 802.1x; I'd really like some general guidelines and help here, and some sort of implementation guide would also be very useful.

  Read the article

• use of CISCO XML gateway Vs BIG IP ASM module as the XML firewall in an architecture

  - by Rajeev

  Hi, I am looking for the advantages and disadvantages of using Cisco XML gateway and BIG IP ASM module in a network.

  Read the article

• How to send connection type (SSH|Telnet) info in Radius Access Requests on Cisco router?

  - by Gianni Costanzi

  I've configured the following on a cisco router: aaa authentication login default group radius local ! radius-server host x.x.x.x auth-port 1012 acct-port 1013 radius-server host y.y.y.y auth-port 1012 acct-port 1013 radius-server retransmit 1 radius-server timeout 3 radius-server key 7 xxxxxxxxx I'd like to be able to specify some radius options in order to add information about the type of connection for which a user is being authenticated, i.e. I'd like the radius server to receive in the Cisco Router's Radius Access Request information about the connection being SSH or Telnet.. I'd like to find something that automatically adds this info in the access request, without specific configurations on VTY lines dedicated to SSH and to Telnet. Any idea about that?

  Read the article

• What's causing "shutdown state" after TFTP reloaded Cisco `running-config` on 871?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I tested the 871's flash memory with fsck and rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config?

  Read the article

• What are steps to upgrade an cisco UCS B series system vmware vsphere from 4.1 to 5.0

  - by Gk.

  I have a Cisco UCS B-series system with 1.4 firmware running vsphere 4.1 (ESX) + Nexus 1000V. I want upgrade all that stuff to vsphere 5.0 without downtime. I tried to find any documentation describe all steps needed to do it, but cannot found anything clear. Here is my plan: Upgrade firmware of UCS from 1.4 to 2.0. Doc: http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/upgrading/from1.4/to2.0/b_UpgradingCiscoUCSFrom1.4To2.0.html Upgrade all vcenter, hosts+VEM, virtual machines, datastores using VMWare best practice. Is it OK? Am I missing something? Thank you, giobuon.

  Read the article

• What are my options in replacing the noisy fan in my Linksys Cisco SRW2008P managed GigE switch?

  - by Fred Sobotka

  My first managed GigE switch, the Linksys SRW2008, was a dream, until it started randomly chattering on various ports. That started while I was on the road all the time, which made it take forever to diagnose, but that's a different problem. When I finally determined that the switch was bad, it was still covered by warranty by Linksys/Cisco, so I opened an RMA ticket and returned it. Unfortunately, Linksys/Cisco "upgraded" my replacement switch to a SRW2008P, which has Power over Ethernet features I never planned on using. That by itself wasn't so bad, but it's my guess that the inclusion of PoE functions in this model required a tiny, super-loud internal fan to keep everything cool. This wasn't something I wanted or asked for, but, now that I am stuck with it, I am investigating options for replacing that little internal fan with something far quieter. For example, if I attach a larger fan to the outsite of the chassis, I think it could push enough air to replace the stock fan that is currently there. Any advice on carrying this out? I have no interest in melting my switch due to insufficient ventilation.

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >