Search Results

Search found 401 results on 17 pages for 'hw'.

Page 16/17 | < Previous Page | 12 13 14 15 16 17  | Next Page >

• External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

  - by kimangroo

  I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

  Read the article

• No GLX on Intel card with multiseat with additional nVidia card

  - by MeanEYE

  I have multiseat configured and my Xorg has 2 server layouts. One is for nVidia card and other is for Intel card. They both work, but display server assigned to Intel card doesn't have hardware acceleration since DRI and GLX module being used is from nVidia driver. So my question is, can I configure layouts somehow to use right DRI and GLX with each card? My Xorg.conf: Section "ServerLayout" Identifier "Default" Screen 0 "Screen0" 0 0 Option "Xinerama" "0" EndSection Section "ServerLayout" Identifier "TV" Screen 0 "Screen1" 0 0 Option "Xinerama" "0" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E198WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 610" EndSection Section "Device" Identifier "Device1" Driver "intel" BusID "PCI:0:2:0" Option "AccelMethod" "uxa" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "nvidiaXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-0: nvidia-auto-select +1440+0, DFP-1: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Log file for Intel: [ 18.239] X.Org X Server 1.13.0 Release Date: 2012-09-05 [ 18.239] X Protocol Version 11, Revision 0 [ 18.239] Build Operating System: Linux 2.6.24-32-xen x86_64 Ubuntu [ 18.239] Current Operating System: Linux bytewiper 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 [ 18.239] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-18-generic root=UUID=fc0616fd-f212-4846-9241-ba4a492f0513 ro quiet splash [ 18.239] Build Date: 20 September 2012 11:55:20AM [ 18.239] xorg-server 2:1.13.0+git20120920.70e57668-0ubuntu0ricotz (For technical support please see http://www.ubuntu.com/support) [ 18.239] Current version of pixman: 0.26.0 [ 18.239] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 18.239] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 18.239] (==) Log file: "/var/log/Xorg.1.log", Time: Wed Nov 21 18:32:14 2012 [ 18.239] (==) Using config file: "/etc/X11/xorg.conf" [ 18.239] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 18.239] (++) ServerLayout "TV" [ 18.239] (**) |-->Screen "Screen1" (0) [ 18.239] (**) | |-->Monitor "Monitor1" [ 18.240] (**) | |-->Device "Device1" [ 18.240] (**) Option "Xinerama" "0" [ 18.240] (==) Automatically adding devices [ 18.240] (==) Automatically enabling devices [ 18.240] (==) Automatically adding GPU devices [ 18.240] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/Type1, built-ins [ 18.240] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules" [ 18.240] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 18.240] (II) Loader magic: 0x7f6917944c40 [ 18.240] (II) Module ABI versions: [ 18.240] X.Org ANSI C Emulation: 0.4 [ 18.240] X.Org Video Driver: 13.0 [ 18.240] X.Org XInput driver : 18.0 [ 18.240] X.Org Server Extension : 7.0 [ 18.240] (II) config/udev: Adding drm device (/dev/dri/card0) [ 18.241] (--) PCI: (0:0:2:0) 8086:0152:1043:84ca rev 9, Mem @ 0xf7400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f000/64 [ 18.241] (--) PCI:*(0:1:0:0) 10de:104a:1458:3546 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/134217728, 0xe8000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288 [ 18.241] (II) Open ACPI successful (/var/run/acpid.socket) [ 18.241] Initializing built-in extension Generic Event Extension [ 18.241] Initializing built-in extension SHAPE [ 18.241] Initializing built-in extension MIT-SHM [ 18.241] Initializing built-in extension XInputExtension [ 18.241] Initializing built-in extension XTEST [ 18.241] Initializing built-in extension BIG-REQUESTS [ 18.241] Initializing built-in extension SYNC [ 18.241] Initializing built-in extension XKEYBOARD [ 18.241] Initializing built-in extension XC-MISC [ 18.241] Initializing built-in extension SECURITY [ 18.241] Initializing built-in extension XINERAMA [ 18.241] Initializing built-in extension XFIXES [ 18.241] Initializing built-in extension RENDER [ 18.241] Initializing built-in extension RANDR [ 18.241] Initializing built-in extension COMPOSITE [ 18.241] Initializing built-in extension DAMAGE [ 18.241] Initializing built-in extension MIT-SCREEN-SAVER [ 18.241] Initializing built-in extension DOUBLE-BUFFER [ 18.241] Initializing built-in extension RECORD [ 18.241] Initializing built-in extension DPMS [ 18.241] Initializing built-in extension X-Resource [ 18.241] Initializing built-in extension XVideo [ 18.241] Initializing built-in extension XVideo-MotionCompensation [ 18.241] Initializing built-in extension XFree86-VidModeExtension [ 18.241] Initializing built-in extension XFree86-DGA [ 18.241] Initializing built-in extension XFree86-DRI [ 18.241] Initializing built-in extension DRI2 [ 18.241] (II) LoadModule: "glx" [ 18.241] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/libglx.so [ 18.247] (II) Module glx: vendor="NVIDIA Corporation" [ 18.247] compiled for 4.0.2, module version = 1.0.0 [ 18.247] Module class: X.Org Server Extension [ 18.247] (II) NVIDIA GLX Module 310.19 Thu Nov 8 01:12:43 PST 2012 [ 18.247] Loading extension GLX [ 18.247] (II) LoadModule: "intel" [ 18.248] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so [ 18.248] (II) Module intel: vendor="X.Org Foundation" [ 18.248] compiled for 1.13.0, module version = 2.20.13 [ 18.248] Module class: X.Org Video Driver [ 18.248] ABI class: X.Org Video Driver, version 13.0 [ 18.248] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale, Sandybridge Desktop (GT1), Sandybridge Desktop (GT2), Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1), Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+), Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2), Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server, Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2), Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2), Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2), Haswell Server (GT2+), Haswell SDV Desktop (GT1), Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+), Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2), Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1), Haswell SDV Server (GT2), Haswell SDV Server (GT2+), Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2), Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1), Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+), Haswell ULT Server (GT1), Haswell ULT Server (GT2), Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1), Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+), Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2), Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1), Haswell CRW Server (GT2), Haswell CRW Server (GT2+), ValleyView PO board [ 18.248] (++) using VT number 8 [ 18.593] (II) intel(0): using device path '/dev/dri/card0' [ 18.593] (**) intel(0): Depth 24, (--) framebuffer bpp 32 [ 18.593] (==) intel(0): RGB weight 888 [ 18.593] (==) intel(0): Default visual is TrueColor [ 18.593] (**) intel(0): Option "AccelMethod" "uxa" [ 18.593] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Desktop (GT1) [ 18.593] (**) intel(0): Relaxed fencing enabled [ 18.593] (**) intel(0): Wait on SwapBuffers? enabled [ 18.593] (**) intel(0): Triple buffering? enabled [ 18.593] (**) intel(0): Framebuffer tiled [ 18.593] (**) intel(0): Pixmaps tiled [ 18.593] (**) intel(0): 3D buffers tiled [ 18.593] (**) intel(0): SwapBuffers wait enabled ... [ 20.312] (II) Module fb: vendor="X.Org Foundation" [ 20.312] compiled for 1.13.0, module version = 1.0.0 [ 20.312] ABI class: X.Org ANSI C Emulation, version 0.4 [ 20.312] (II) Loading sub module "dri2" [ 20.312] (II) LoadModule: "dri2" [ 20.312] (II) Module "dri2" already built-in [ 20.312] (==) Depth 24 pixmap format is 32 bpp [ 20.312] (II) intel(0): [DRI2] Setup complete [ 20.312] (II) intel(0): [DRI2] DRI driver: i965 [ 20.312] (II) intel(0): Allocated new frame buffer 1920x1080 stride 7680, tiled [ 20.312] (II) UXA(0): Driver registered support for the following operations: [ 20.312] (II) solid [ 20.312] (II) copy [ 20.312] (II) composite (RENDER acceleration) [ 20.312] (II) put_image [ 20.312] (II) get_image [ 20.312] (==) intel(0): Backing store disabled [ 20.312] (==) intel(0): Silken mouse enabled [ 20.312] (II) intel(0): Initializing HW Cursor [ 20.312] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 20.313] (**) intel(0): DPMS enabled [ 20.313] (==) intel(0): Intel XvMC decoder enabled [ 20.313] (II) intel(0): Set up textured video [ 20.313] (II) intel(0): [XvMC] xvmc_vld driver initialized. [ 20.313] (II) intel(0): direct rendering: DRI2 Enabled [ 20.313] (==) intel(0): hotplug detection: "enabled" [ 20.332] (--) RandR disabled [ 20.335] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 20.335] (II) intel(0): Setting screen physical size to 508 x 285 [ 20.338] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm [ 20.340] (II) config/udev: Adding input device Power Button (/dev/input/event1) [ 20.340] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 20.340] (II) LoadModule: "evdev" [ 20.340] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so

  Read the article

• The SPARC SuperCluster

  - by Karoly Vegh

  Oracle has been providing a lead in the Engineered Systems business for quite a while now, in accordance with the motto "Hardware and Software Engineered to Work Together." Indeed it is hard to find a better definition of these systems.  Allow me to summarize the idea. It is:  Build a compute platform optimized to run your technologies Develop application aware, intelligently caching storage components Take an impressively fast network technology interconnecting it with the compute nodes Tune the application to scale with the nodes to yet unseen performance Reduce the amount of data moving via compression Provide this all in a pre-integrated single product with a single-pane management interface All these ideas have been around in IT for quite some time now. The real Oracle advantage is adding the last one to put these all together. Oracle has built quite a portfolio of Engineered Systems, to run its technologies - and run those like they never ran before. In this post I'll focus on one of them that serves as a consolidation demigod, a multi-purpose engineered system.  As you probably have guessed, I am talking about the SPARC SuperCluster. It has many great features inherited from its predecessors, and it adds several new ones. Allow me to pick out and elaborate about some of the most interesting ones from a technological point of view.  I. It is the SPARC SuperCluster T4-4. That is, as compute nodes, it includes SPARC T4-4 servers that we learned to appreciate and respect for their features: The SPARC T4 CPUs: Each CPU has 8 cores, each core runs 8 threads. The SPARC T4-4 servers have 4 sockets. That is, a single compute node can in parallel, simultaneously  execute 256 threads. Now, a full-rack SPARC SuperCluster has 4 of these servers on board. Remember the keyword demigod.  While retaining the forerunner SPARC T3's exceptional throughput, the SPARC T4 CPUs raise the bar with single performance too - a humble 5x better one than their ancestors.  actually, the SPARC T4 CPU cores run in both single-threaded and multi-threaded mode, and switch between these two on-the-fly, fulfilling not only single-threaded OR multi-threaded applications' needs, but even mixed requirements (like in database workloads!). Data security, anyone? Every SPARC T4 CPU core has a built-in encryption engine, that is, encryption algorithms cast into silicon.  A PCI controller right on the chip for customers who need I/O performance.  Built-in, no-cost Virtualization:  Oracle VM for SPARC (the former LDoms or Logical Domains) is not a server-emulation virtualization technology but rather a serverpartitioning one, the hypervisor runs in the server firmware, and all the VMs' HW resources (I/O, CPU, memory) are accessed natively, without performance overhead.  This enables customers to run a number of Solaris 10 and Solaris 11 VMs separated, independent of each other within a physical server II. For Database performance, it includes Exadata Storage Cells - one of the main reasons why the Exadata Database Machine performs at diabolic speed. What makes them important? They provide DB backend storage for your Oracle Databases to run on the SPARC SuperCluster, that is what they are built and tuned for DB performance.  These storage cells are SQL-aware.  That is, if a SPARC T4 database compute node executes a query, it doesn't simply request tons of raw datablocks from the storage, filters the received data, and throws away most of it where the statement doesn't apply, but provides the SQL query to the storage node too. The storage cell software speaks SQL, that is, it is able to prefilter and through that transfer only the relevant data. With this, the traffic between database nodes and storage cells is reduced immensely. Less I/O is a good thing - as they say, all the CPUs of the world do one thing just as fast as any other - and that is waiting for I/O.  They don't only pre-filter, but also provide data preprocessing features - e.g. if a DB-node requests an aggregate of data, they can calculate it, and handover only the results, not the whole set. Again, less data to transfer.  They support the magical HCC, (Hybrid Columnar Compression). That is, data can be stored in a precompressed form on the storage. Less data to transfer.  Of course one can't simply rely on disks for performance, there is Flash Storage included there for caching.  III. The low latency, high-speed backbone network: InfiniBand, that interconnects all the members with: Real High Speed: 40 Gbit/s. Full Duplex, of course. Oh, and a really low latency.  RDMA. Remote Direct Memory Access. This technology allows the DB nodes to do exactly that. Remotely, directly placing SQL commands into the Memory of the storage cells. Dodging all the network-stack bottlenecks, avoiding overhead, placing requests directly into the process queue.  You can also run IP over InfiniBand if you please - that's the way the compute nodes can communicate with each other.  IV. Including a general-purpose storage too: the ZFSSA, which is a unified storage, providing NAS and SAN access too, with the following features:  NFS over RDMA over InfiniBand. Nothing is faster network-filesystem-wise.  All the ZFS features onboard, hybrid storage pools, compression, deduplication, snapshot, replication, NFS and CIFS shares Storageheads in a HA-Cluster configuration providing availability of the data  DTrace Live Analytics in a web-based Administration UI Being a general purpose application data storage for your non-database applications running on the SPARC SuperCluster over whichever protocol they prefer, easily replicating, snapshotting, cloning data for them.  There's a lot of great technology included in Oracle's SPARC SuperCluster, we have talked its interior through. As for external scalability: you can start with a half- of full- rack SPARC SuperCluster, and scale out to several racks - that is, stacking not separate full-rack SPARC SuperClusters, but extending always one large instance of the size of several full-racks. Yes, over InfiniBand network. Add racks as you grow.  What technologies shall run on it? SPARC SuperCluster is a general purpose scaleout consolidation/cloud environment. You can run Oracle Databases with RAC scaling, or Oracle Weblogic (end enjoy the SPARC T4's advantages to run Java). Remember, Oracle technologies have been integrated with the Oracle Engineered Systems - this is the Oracle on Oracle advantage. But you can run other software environments such as SAP if you please too. Run any application that runs on Oracle Solaris 10 or Solaris 11. Separate them in Virtual Machines, or even Oracle Solaris Zones, monitor and manage those from a central UI. Here the key takeaways once again: The SPARC SuperCluster: Is a pre-integrated Engineered System Contains SPARC T4-4 servers with built-in virtualization, cryptography, dynamic threading Contains the Exadata storage cells that intelligently offload the burden of the DB-nodes  Contains a highly available ZFS Storage Appliance, that provides SAN/NAS storage in a unified way Combines all these elements over a high-speed, low-latency backbone network implemented with InfiniBand Can grow from a single half-rack to several full-rack size Supports the consolidation of hundreds of applications To summarize: All these technologies are great by themselves, but the real value is like in every other Oracle Engineered System: Integration. All these technologies are tuned to perform together. Together they are way more than the sum of all - and a careful and actually very time consuming integration process is necessary to orchestrate all these for performance. The SPARC SuperCluster's goal is to enable infrastructure operations and offer a pre-integrated solution that can be architected and delivered in hours instead of months of evaluations and tests. The tedious and most importantly time and resource consuming part of the work - testing and evaluating - has been done.  Now go, provide services.   -- charlie  

  Read the article

• Oracle Partner Store (OPS) New Enhancements

  - by Kristin Rose

  Effective June 29th, Oracle Partner Store (OPS) will release the enhancements listed below to improve your overall ordering experience. v Online Transactional Oracle Master Agreement (Online TOMA) The Online TOMA enables end users to execute a transactional end user license agreement with Oracle. The new Online TOMA in OPS will replace the need for you to obtain a signed hard copy of the TOMA from the end user. You will now initiate the Online TOMA via OPS. Navigation: OPS Home > Order Tools > Online TOMA Query > Request Online TOMA> End User Contact, click “Select for TOMA” > Select Language > Submit (an automated email is sent immediately to the requestor and the end user) Ø The Online TOMA can also be initiated from the ‘My OPS’ tab. Under the Online TOMA Query section partners can track Online TOMA request details submitted to end users. The status of the Online TOMA request and the OMA Key generated (once Ts&Cs of the Online TOMA are accepted by an end user) are also displayed in this table. There is also the ability to resend pending Online TOMA requests by clicking ‘Resend’. Navigation: OPS Home > Order Tools > Online TOMA Query For more details on the Transactional OMA, please click here. v Convert Deals to Carts The partner deal registration system within OPS will now allow you to convert approved deals into carts with a simple click of a button. VADs can use Deal to Cart on all of their partners' registrations, regardless of whether they submitted on their partner's behalf, or the partner submitted themselves. Navigation: Login > Deal Registrations > Deal Registration List > Open the approved deal > Click Deal Reg ID number link to open > Click on 'Create Cart' link You can locate your newly created cart in the Saved Carts section of OPS. Links are also available from within an open deal or from the Deal Registration List. Click on the cart number to proceed. v Partner Opportunity Management: Deal Registration on OPS now allows you to see updated information on your opportunities from Oracle’s Fusion CRM opportunity management system.  Key fields such as close date, sales stage, products and status can be viewed by clicking the opportunity ID associated with the deal registration.  This new feature allows you to see regular updates to your opportunities after registrations are approved.  Through ongoing communication with Oracle Channel Managers and Sales Reps, you can ensure that Oracle has the latest information on your active registered deals. v Product Recommendations: When adding products to the Deal Registrations tab, OPS will now show additional products that you can try to include to maximize your sale and rebate. v Advanced Customer Support(ACS) Services Note: This will be available from July 9th. Initiate the purchase of the complete stack (HW/SW/Services) online with one single OPS order. More ACS services now supported online with exception of Start-Up Pack: · New SW installation services for Standard Configurations & stand alone System Software. · New Pre-production & Go-live services for Standard & Engineered Systems · New SW configuration & Platinum Pre-Production & Go-Live services for Engineered Systems · New Travel & Expenses Estimate included · New Partner & VAD volume discount supported v Software as a Service (SaaS) for Independent Software Vendors (ISVs): Oracle SaaS ISVs can now use OPS to submit their monthly usage reports to Oracle within 20 days after the end of every month. Navigation: OPS Home > Cart > Transaction Type: Partner SaaS for ISV’s > Add Eligible Products > Check out v Existing Approvals: In an effort to reduce the processing time of discount approvals, we have added a new section in the Request Approval page for you to communicate pre-existing approvals without having to attach the DAT. Just enter the Approval ID and submit your request. In case of existing software approvals, you will be required to submit the DAT with the Contact Information section filled out. v Additional data for Shipping Box Labels and Packing Slips OPS now has additional fields in the Shipping Notes section for you to add PO details. This will help you easily identify shipments as they arrive. Partners will have an End User PO field, whereas VADs will have VAR and End User PO fields. v Shipping Notes on OPS Hardware delivery Shipping Notes will now have multiple options to better suit your requirements. v Reminders for Royalty Reporting Partners: If you have not submitted your royalty report online, OPS will now send an automated alert to remind you. v Order Tracker Changes: · Order Tracker will now have a deal reg flag (Yes/No). You can now clearly distinguish between orders that have registered opportunities. · All lines of the order will be visible in the order details list. v Changes in Terminology · You will notice textual changes on some of our labels and messages relating to approval requests. “Discount Requests” has been replaced with “Approval Requests” to cater to some of our other offerings. · First Line Support (FLS) transaction type has been renamed to Support Provider Partner (SPP). OPS Support For more details on these enhancements, please request a training here. For assistance on the Oracle Partner Store, please contact the OPS support team in your region. NAMER: [email protected] LAD: [email protected] EMEA : [email protected] APAC: [email protected] Japan: [email protected] You can even call us on our Hotline! Find your local number here.     Thank you, Oracle Partner Store Support Team      

  Read the article

• Delay of mail delivery - Hosted exchange provider

  - by alex

  Hi, I recently signed up to a new hosted email provider. When I send mail (from OWA, OR Outlook) there is a delay of up to 3 minutes from when i send the message, to when it's received (in my gmail account for example) I've listed the headers below. Is there anything I can advise my new email host to do? My previous email host delivers within 5 seconds!! New email provider: Delivered-To: ****.*****@******.co.uk.test-google-a.com Received: by 10.223.120.148 with SMTP id d20cs333125far; Mon, 30 Nov 2009 08:49:43 -0800 (PST) Received: by 10.213.106.202 with SMTP id y10mr4864870ebo.35.1259599782838; Mon, 30 Nov 2009 08:49:42 -0800 (PST) Return-Path: Received: from relay005.apm-internet.net (relay005.apm-internet.net [85.119.248.8]) by mx.google.com with SMTP id 26si13016480ewy.43.2009.11.30.08.49.42; Mon, 30 Nov 2009 08:49:42 -0800 (PST) Received-SPF: neutral (google.com: 85.119.248.8 is neither permitted nor denied by best guess record for domain of ****@*******.com) client-ip=85.119.248.8; Authentication-Results: mx.google.com; spf=neutral (google.com: 85.119.248.8 is neither permitted nor denied by best guess record for domain of ****@*******.com) smtp.mail=****@*******.com Received: (qmail 63915 invoked from network); 30 Nov 2009 16:49:41 -0000 Received: from unknown (HELO mx-out-manc2.simplymailsolutions.com) (88.151.129.22) by relay005.apm-internet.net with SMTP; 30 Nov 2009 16:49:42 -0000 X-APM-IP: 88.151.129.22 X-APM-Score: 4 Received-SPF: none (relay005.apm-internet.net: domain at alexjamesbrown.com does not designate permitted sender hosts) Received: from [10.1.20.1] (helo=win-s-manc1.shared.ifeltd.com) by mx-out-manc2.simplymailsolutions.com with esmtp (Exim 4.63) (envelope-from ) id 1NF9QZ-0005By-Hw for ****.*****@******.co.uk; Mon, 30 Nov 2009 16:48:46 +0000 Received: from sha-exch8.shared.ifeltd.com ([10.1.20.8]) by win-s-manc1.shared.ifeltd.com with Microsoft SMTPSVC(6.0.3790.3959); Mon, 30 Nov 2009 16:48:34 +0000 Received: from sha-exch9.shared.ifeltd.com ([10.1.20.9]) by sha-exch8.shared.ifeltd.com with Microsoft SMTPSVC(6.0.3790.3959); Mon, 30 Nov 2009 16:48:34 +0000 Received: from SHA-EXCH13.shared.ifeltd.com (10.1.20.13) by sha-exch9.shared.ifeltd.com (10.1.20.9) with Microsoft SMTP Server (TLS) id 8.1.393.1; Mon, 30 Nov 2009 16:48:25 +0000 Received: from SHA-EXCH12.shared.ifeltd.com ([fe80::ecba:36d0:eec5:c928]) by SHA-EXCH13.shared.ifeltd.com ([fe80::212b:916c:70c7:a4e5%11]) with mapi; Mon, 30 Nov 2009 16:48:05 +0000 From: Alex Brown To: "****.*****@*****.co.uk" Date: Mon, 30 Nov 2009 16:48:04 +0000 Subject: testing Thread-Topic: testing Thread-Index: AQHKcdzZg4oiDsOYIEio/7k6bCk8BQ== Message-ID: Accept-Language: en-US, en-GB Content-Language: en-GB X-MS-Has-Attach: X-MS-TNEF-Correlator: acceptlanguage: en-US, en-GB Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: quoted-printable MIME-Version: 1.0 X-OriginalArrivalTime: 30 Nov 2009 16:48:34.0235 (UTC) FILETIME=[F48178B0:01CA71DC] Here are the headers using my previous exchange host: Delivered-To: ****.*****@******.co.uk.test-google-a.com Received: by 10.223.120.148 with SMTP id d20cs333076far; Mon, 30 Nov 2009 08:48:35 -0800 (PST) Received: by 10.213.2.70 with SMTP id 6mr4797985ebi.25.1259599715739; Mon, 30 Nov 2009 08:48:35 -0800 (PST) Return-Path: Received: from relay005.apm-internet.net (relay005.apm-internet.net [85.119.248.8]) by mx.google.com with SMTP id 26si13030993ewy.23.2009.11.30.08.48.35; Mon, 30 Nov 2009 08:48:35 -0800 (PST) Received-SPF: neutral (google.com: 85.119.248.8 is neither permitted nor denied by best guess record for domain of ****@*********.com) client-ip=85.119.248.8; Authentication-Results: mx.google.com; spf=neutral (google.com: 85.119.248.8 is neither permitted nor denied by best guess record for domain of ****@*********.com) smtp.mail=****@*********.com Received: (qmail 60920 invoked from network); 30 Nov 2009 16:48:34 -0000 Received: from unknown (HELO MTAb.MsExchange2007.com) (89.31.236.50) by relay005.apm-internet.net with SMTP; 30 Nov 2009 16:48:35 -0000 X-APM-IP: 89.31.236.50 X-APM-Score: 1 Received-SPF: none (relay005.apm-internet.net: domain at alexjamesbrown.com does not designate permitted sender hosts) Received: from EXHUB02.SL.local (no.ptr.hostlogic.biz [89.31.236.28]) by MTAb.MsExchange2007.com (Spam Firewall) with ESMTP id B677A34FE0F for ; Mon, 30 Nov 2009 16:48:33 +0000 (GMT) Received: from EXHUB02.SL.local (no.ptr.hostlogic.biz [89.31.236.28]) by MTAb.MsExchange2007.com with ESMTP id 8X5B8V4tExVzoNyU for ; Mon, 30 Nov 2009 16:48:34 +0000 (GMT) Received: from EXCCR03STORE.SL.local ([10.0.0.2]) by EXHUB02.SL.local ([192.168.92.64]) with mapi; Mon, 30 Nov 2009 16:48:31 +0000 From: Alex James Brown To: "****.*****@******.co.uk" Date: Mon, 30 Nov 2009 16:48:30 +0000 Subject: testing from o Thread-Topic: testing from o Thread-Index: AQHKcdzyY1iBFWiol0ykG6xPQUZiTg== Message-ID: Accept-Language: en-US, en-GB Content-Language: en-GB X-MS-Has-Attach: X-MS-TNEF-Correlator: acceptlanguage: en-US, en-GB Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: quoted-printable MIME-Version: 1.0

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• ESXi v5.5 is having random crashes

  - by Darkmage

  HW: Type: HP Proliant ML350 G5 RAM 22GB CPU 1 x Intel Xenon E5405 2.00GHz OP: ESXi 5.5 just updated from 5.1 to try and fix the crashes occurring on ESXi 5.1 on same hardware. I'm trying to find the error on why one of our servers is crashing, it has had two lock ups in 24 hours now. The internal error light on the front is blinking red, on the inside only "#5 and #6 page 76 manual" the "Processor 2" light "amber" and the "Power" light "green" is shining. in the logs the only errors i can see in the relevant time frame is in log under. Is this the reason? or is there anything else i can do to try and log/locate the error. from zcat syslog.6.gz | less 2014-05-26T11:55:47Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:55:47Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:55:47Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:53Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:57Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:01Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:04Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:15Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:56:17Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:56:17Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:23Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:27Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:31Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:46Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:48Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files -- manual

  Read the article

• Is the Cloud ready for an Enterprise Java web application? Seeking a JEE hosting advice.

  - by Jakub Holý

  Greetings to all the smart people around here! I'd like to ask whether it is feasible or a good idea at all to deploy a Java enterprise web application to a Cloud such as Amazon EC2. More exactly, I'm looking for infrastructure options for an application that shall handle few hundred users with long but neither CPU nor memory intensive sessions. I'm considering dedicated servers, virtual private servers (VPSs) and EC2. I've noticed that there is a project called JBoss Cloud so people are working on enabling such a deployment, on the other hand it doesn't seem to be mature yet and I'm not sure that the cloud is ready for this kind of applications, which differs from the typical cloud-based applications like Twitter. Would you recommend to deploy it to the cloud? What are the pros and cons? The application is a Java EE 5 web application whose main function is to enable users to compose their own customized Product by combining the available Parts. It uses stateless and stateful session beans and JPA for persistence of entities to a RDBMS and fetches information about Parts from the company's inventory system via a web service. Aside of external users it's used also by few internal ones, who are authenticated against the company's LDAP. The application should handle around 300-400 concurrent users building their product and should be reasonably scalable and available though these qualities are only of a medium importance at this stage. I've proposed an architecture consisting of a firewall (FW) and load balancer supporting sticky sessions and https (in the Cloud this would be replaced with EC2's Elastic Load Balancing service and FW on the app. servers, in a physical architecture the load-balancer would be a HW), then two physical clustered application servers combined with web servers (so that if one fails, a user doesn't loose his/her long built product) and finally a database server. The DB server would need a slave backup instance that can replace the master instance if it fails. This should provide reasonable availability and fault tolerance and provide good scalability as long as a single RDBMS can keep with the load, which should be OK for quite a while because most of the operations are done in the memory using a stateful bean and only occasionally stored or retrieved from the DB and the amount of data is low too. A problematic part could be the dependency on the remote inventory system webservice but with good caching of its outputs in the application it should be OK too. Unfortunately I've only vague idea of the system resources (memory size, number and speed of CPUs/cores) that such an "average Java EE application" for few hundred users needs. My rough and mostly unfounded estimate based on actual Amazon offerings is that 1.7GB and a single, 2-core "modern CPU" with speed around 2.5GHz (the High-CPU Medium Instance) should be sufficient for any of the two application servers (since we can handle higher load by provisioning more of them). Alternatively I would consider using the Large instance (64b, 7.5GB RAM, 2 cores at 1GHz) So my question is whether such a deployment to the cloud is technically and financially feasible or whether dedicated/VPS servers would be a better option and whether there are some real-world experiences with something similar. Thank you very much! /Jakub Holy PS: I've found the JBoss EAP in a Cloud Case Study that shows that it is possible to deploy a real-world Java EE application to the EC2 cloud but unfortunately there're no details regarding topology, instance types, or anything :-(

  Read the article

• CodePlex Daily Summary for Friday, April 16, 2010

  CodePlex Daily Summary for Friday, April 16, 2010New Projects[C#] UML Touch: This project is my master thesis project for Msc Software Engineering at Oxford Brookes univesity. The goal of this project is to develop a UML Edi...3D Chart Reports, using ASP.NET 2.0: Project focuses on the visibility of internal supply chain management process. The objective is materialized, using MSChart and hence provides asse...Active Directory Health: ActiveDirectoryHealth (ADHealth) Aim: To create a suite of tools to allow an Active Directory administrator monitor and identify problems, particu...Art4Desktop: Aplicação desktop simplesAuto Increment field for any entity in MS CRM: Auto Increment field for any entity in MS CRM will add an attribute in any entity which will be auto increment type.Convection Game Engine (Basic Edition): A basic 2D game engine written in C# using XNA 3.1CSharp Intellisense: VS 2010 IntelliSense plug-in Provides custom IntelliSense for the CSharp Editor that is capable to filter out events, preoperties or methods. ...EP: Generic platform for enterprise applications developed on .NETFile Change Checker: A simple windows form application that checks and copies all modified files given a specified date. It aims to help developers that use Visual Stu...Folder: Folder is a puzzle platformer game, which provides you a whole new experience. You can fold objects in game play; a wall becomes a road, a high sti...Industrial Dashboard: WCF service that allows executing SQL Server stored procedures straight from javascript code, enabling sending and receiving structured data withou...kafrilion: Open Source Platform GameLogikBug.Injection: LogikBug.Injection is an IOC container and is very light weight. It is very simple to use and yet very roboust, there are many options and ways to ...MongoMvc: NoSql with MongoDB, NoRM and ASP.NET MVC. For more details check out the blog post http://weblogs.asp.net/shijuvarghese/archive/2010/04/16/nosql-wi...MOSSDAL: MOSS Data Access Layer for data from the Sharepoint Lists Service: MOSSDAL is a lightweight framework for working with Sharepoint MOSS List data using the List web Service. It can be used with silverlight or regul...Should: This is a set of test framework agnostic extensions assetion extensions. This project was born because test runners Should be independent of the...Software Localization Tool: summaryTIMETABLEASY: planning managerTR9: implementions of t9 technologies from mobile device to personal computer and laptopTrp net tools: net toolTwep: Twep is a JavaScript lib.Using PowerPivot to analyze MS Dynamics NAV: Project show how to prepare MS Dynamics NAV data for analyzing in PowerPivot for Excel. Project include Data Warehouse demo database, sql procedure...vmware virtual mashines management system for education: System for management many classes with PC and VMware virtual mashines (bad english,sorry)WebSite: Mr. John's projectsWebtrends DX and DC Services Libraries: This project is setup to provide assemblies to simplify access to the REST based DX and DC Web Services that Webtrends Provides. For access you ne...YetAnotherFileRenamer: Searches a directory and/or sub-directories for files matching a certain extension and copies and renames them to the same folder. The intent is a...New Releases3D Chart Reports, using ASP.NET 2.0: Beta iscm1.0.0.1: Its first release, might be a tolerant to bugs.A Guide to Parallel Programming: Drop 2 - Guide Chapters 2 and 5, accompanying code: This is Drop 2 with just the Guide Chapters 2 and 5 and the accompanying code samples. This drop requires Visual Studio 2010 Beta 2 or later in ord...AnimeJ: AnimeJ 1.1: This new release features reversible animations. It is fully backward compatible, and by simply specifying an additional parameter to Run() you can...AutoPoco: AutoPoco 0.4: A load of additions to the convention system Inheritance precedence added And a pile of extra data sourcesCSharp Intellisense: V1.5: CSharpIntellisensePresenter(Free) Created by: Bnaya Eshet (Bnaya Eshet (credit to Karl Shifflett)) Last Updated: Tuesday, April 13, 2010 Version...DevTreks -social budgeting that improves lives and livelihoods: Social Budgeting Web Software, DevTreks alpha 4: Alpha 4 upgrades all story-telling with one very basic, simple, 'story' data pattern, schema, and stylesheet. Basic, simple, stories and eBook pa...ESPEHA: Espeha 4.3: Deletion of categories and tasks via F8 Saving on CtrlS, CtrlShiftS Navigating to search on CtrlF Hiding on CtrlQ, CtrlX, CtrlH, Q, X, H + Drag ...Folder Bookmarks: Folder Bookmarks 1.4.4: This is the latest version of Folder Bookmarks (1.4.4), with general improvements. It has an installer - it will create a directory 'CPascoe' in My...HouseFly controls: HouseFly controls alpha 0.9.1: Version 0.9.1 alpha release of HouseFly controlsIndustrial Dashboard: 2.0 Beta: 2.0 Beta includes : IndustrialDashboard Framework Sample widgets : TabularReport, DropDownPicker, DatePicker, ScopePicker Sample html pageskdar: KDAR 0.0.20: KDAR - Kernel Debugger Anti Rootkit - signature's bases updated - many bugs fixedLogikBug.Injection: Initial Release: This project is dependent upon Microsoft.Practices.ServiceLocation.IServiceLocator and must be referenced when referencing LogikBug.Injection.Mesopotamia Experiment: Mesopotamia 1.2.72: New Features - Select organims to load in sim or in hw mode Fixes - fixed robotics engine not shutting down properly - selects new robotics port o...MobySharp: MobySharp 1.1: Fixed GetComments Added the new Likes featureMongoMvc: NoSQL with MongoDB, NoRM and ASP.NET MVC: A demo on NoSQL with MongoDB, NoRM and ASP.NET MVC. To run the demo application do the ollowing actions. 1. Create a directory call C:\data\...NetMassDownloader: Release 1.6.0.0: Mass Downloader For .Net Framework which allows you do download .Net Framework source code all at once.Offline debugging for VS2005 , VS2008 , Code...Nito.KitchenSink: Version 4: Features added in this release: PDBs are source-indexed to CodePlex, so it should be possible to step through the code (with on-demand downloads) w...Nito.KitchenSink: Version 5: The only feature for this release is support of the .NET 4.0 platform. Dependencies Nito.Linq 0.4 Beta (released 2010-04-15) Rx 1.0.2441.0 (rele...Nito.LINQ: Beta (v0.4): Rx version The "with Rx" versions of Nito.LINQ are built against Rx 1.0.2441.0, released 2010-04-15. Breaking changes IEnumerable<T>.Min and IEnum...N-Twill Twitter Client for VB.NET: NTWILL PROJECT 15-abril-2010: Este archivo es un Zip que contiene el proyecto hasta este punto editado... tiene algunas que otras funciones, pero lo cuelgo para tener un referen...PanBrowser: 1.2.0: added screensaver support, hit a key to exit, up/down keys cycle through images.PersianDateTimePicker, PersianMonthCalendar: PersianDatetimePicker,PersianMonthCalendar: PersianDatetimePicker,PersianMonthCalendar 1.1 releasesPokeIn Comet Ajax Library: PokeIn Library v03: New Features! Client MessageLog Management Added CrossBrowser Script Injector Added to work with non ajax supported browsers and activeX disabled...PokeIn Comet Ajax Library: PokeIn Sample VS09: Sample Project of PokeIn VS09. Contains version 0.3 of LibraryPokeIn Comet Ajax Library: PokeIn Sample VS10: Sample Visual Studio 10 project for PokeIn. Contains v03 Library of PokeInSilverlight Toolkit: April 2010: Suggestions? Features? Questions? Ask questions in our Silverlight Toolkit forum on Silverlight.net. The forum is the best resource for Silverlig...Software Localization Tool: SharpSLT 0.9: This is the first release of SharpSLT. Features Framework: .Net 3.5 UI language: English Works as standalone and External Tool for Visual C# Ex...Star Trooper for XNA 2D Tutorial: Lesson two content: Here is Lesson two original content for the StarTrooper 2D XNA tutorial. The blog tutorial has now started over on http://xna-uk.net/blogs/darkgen...StyleCop for ReSharper: StyleCop for ReSharper 5.0.14714.1: StyleCop for ReSharper 5.0.14714.1 o StyleCop 4.3.3.0 o ReSharper 5.0.1659.36 o Visual Studio 2008 / Visual Studio 2010 Installation Instructi...TaskUnZip for SSIS: TaskUnZip for SSIS 1.1.1.0 (beta 2): Ver. 1.1.1.0 (beta2) Bug: Correct installation bug. Add: Support SQL SERVER 2008 / 2005 Minor corrections Ver. 1.1.0.0 (Tnx to: Kevin Wendler)...TaskUnZip for SSIS: TaskUnZip for SSIS 1.2.0.0: Ver. 1.2.0.0 Add: Support SQL SERVER 2008 / 2005. Add: recursive compress.* Add: filter option for extract e compress file.* Add: Test archiv...Test Project (ignore): abcde: aaaaadaTR9: TR9 Beta: this setup is first release of the program.TR9: TR9 Source Code: TR9 Source CodeUsing PowerPivot to analyze MS Dynamics NAV: GL sql procedures and demo DB: For using sql procedures and creating DW database, please see Documentation.VivoSocial: VivoSocial 7.1.1: Version 7.1.1 of VivoSocial has been released. If you experienced any issues with the previous version, please update your modules to the 7.1.1 rel...WPF Inspirational Quote Management System: Release 1.1.1: - Changed to only allow one running instance a time. - Custom icon in system tray popup removed for now as this breaks when text size is set to gr...WPF ShaderEffect Generator: WPF ShaderEffect Generator 1.6.1: Just a minor release to fix the problem with resource Uri generation in the C# Shadereffect files. ChangesThe Uri should be correctly generated no...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NETMicrosoft SQL Server Community & SamplesPHPExcelpatterns & practices – Enterprise LibraryMost Active ProjectsRawrpatterns & practices – Enterprise LibraryGMap.NET - Great Maps for Windows Forms & PresentationIndustrial DashboardFarseer Physics EngineIonics Isapi Rewrite FilterNB_Store - Free DotNetNuke Ecommerce Catalog ModuleBlogEngine.NETjQuery Library for SharePoint Web ServicesDotRas

  Read the article

• Why Wifi no longer works 12.04.1

  - by Roger

  starting this morning over wifi (Realtek RTL8188CE) on CLEVO W253HU. May be due to the update before yesterday, more pilot managed, but somehow it worked yesterday. If someone has an idea of the problem. Back command lines: cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 006: ID 192f:0416 Avago Technologies, Pte. Bus 002 Device 004: ID 5986:0315 Acer, Inc lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) lspci -nn | grep -i net 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 03:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) lspci -k 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: i2c-i801 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device 9196 Kernel modules: rtl8192ce 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jme Kernel modules: jme 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: sdhci-pci 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jmb38x_ms Kernel modules: jmb38x_ms sudo lshw -C network *-network NON-RÉCLAMÉ description: Network controller produit: RTL8188CE 802.11b/g/n WiFi Adapter fabriquant: Realtek Semiconductor Co., Ltd. identifiant matériel: 0 information bus: pci@0000:02:00.0 version: 01 bits: 64 bits horloge: 33MHz fonctionnalités: pm msi pciexpress cap_list configuration: latency=0 ressources: portE/S:e000(taille=256) mémoire:f7d00000-f7d03fff *-network description: Ethernet interface produit: JMC250 PCI Express Gigabit Ethernet Controller fabriquant: JMicron Technology Corp. identifiant matériel: 0 information bus: pci@0000:03:00.0 nom logique: eth0 version: 05 numéro de série: 00:90:f5:c1:c6:45 taille: 100Mbit/s capacité: 1Gbit/s bits: 32 bits horloge: 33MHz fonctionnalités: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=full ip=192.168.1.54 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s ressources: irq:44 mémoire:f7c20000-f7c23fff portE/S:d100(taille=128) portE/S:d000(taille=256) mémoire:f7c10000-f7c1ffff mémoire:f7c00000-f7c0ffff lsmod Module Size Used by btusb 18288 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 11 btusb,rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 binfmt_misc 17540 1 snd_hda_codec_realtek 224173 0 dm_crypt 23125 0 snd_hda_codec_hdmi 32474 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_hda_intel 33773 2 snd_hda_codec 127706 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi jmb38x_ms 17646 0 psmouse 87692 0 serio_raw 13211 0 memstick 16569 1 jmb38x_ms snd_seq_midi_event 14899 1 snd_seq_midi rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi mac_hid 13253 0 snd 78855 14 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 205544 2 rtlwifi,mac80211 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid i915 473035 3 drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper jme 41259 0 i2c_algo_bit 13423 1 i915 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci wmi 19256 0 video 19596 1 i915 iwconfig lo no wireless extensions. eth0 no wireless extensions. ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:c1:c6:45 inet adr:192.168.1.54 Bcast:192.168.1.255 Masque:255.255.255.0 adr inet6: fe80::290:f5ff:fec1:c645/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:4513 erreurs:0 :0 overruns:0 frame:0 TX packets:4359 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:3471675 (3.4 MB) Octets transmis:712722 (712.7 KB) Interruption:44 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:686 erreurs:0 :0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 Octets reçus:64556 (64.5 KB) Octets transmis:64556 (64.5 KB) sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. uname -r -m 3.2.0-30-generic x86_64 cat /etc/network/interfaces auto lo iface lo inet loopback nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Connexion filaire 1] ------------------------------------------ Type: Wired Driver: jme State: connected Default: yes HW Address: 00:90:F5:C1:C6:45 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.54 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 sudo rfkill listrfkill list 1: hci0: Bluetooth Soft blocked: no Hard blocked: no The absence of line "Kernel driver in use:" the return of lspci-k made ??me think that it is not loaded yet but he seems to be. lsmod | grep rtl8192ce rtl8192ce 137478 0 rtlwifi 118749 1 rtl8192ce mac80211 506816 2 rtl8192ce,rtlwifi I found something disturbing in / var / log / syslog Sep 14 11:40:11 pcroger kernel: [ 64.048783] rtl8192ce-0:rtl92c_init_sw_vars():<0-0> Failed to request firmware! Sep 14 11:40:11 pcroger kernel: [ 64.048795] rtlwifi-0:rtl_pci_probe():<0-0> Can't init_sw_vars. Sep 14 11:40:11 pcroger kernel: [ 64.048835] rtl8192ce 0000:02:00.0: PCI INT A disabled Sep 14 11:40:11 pcroger kernel: [ 64.943345] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6 frozen Sep 14 11:40:11 pcroger kernel: [ 64.943358] ata1.00: failed command: READ FPDMA QUEUED Sep 14 11:40:11 pcroger kernel: [ 64.943371] ata1.00: cmd 60/00:00:00:68:6a/04:00:0b:00:00/40 tag 0 ncq 524288 in Sep 14 11:40:11 pcroger kernel: [ 64.943374] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) Sep 14 11:40:11 pcroger kernel: [ 64.943381] ata1.00: status: { DRDY } Ubuntu and takes forever to start (2 min).

  Read the article

• How do I prevent missing network from slowing down boot-up?

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Slow boot on Ubuntu 12.04, probable cause the network connection

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• How do you setup the driver for a Philips based TV capture card?

  - by user8270

  Hi, I have a TV card that I have not managed to install with Ubuntu 10.10 i386. I have tried various topics in various forums and I could not install it. I hope you can help me to install it thank you. lspci 01:07.0 Multimedia controller: Philips Semiconductors SAA7130 Video Broadcast Decoder (rev 01) dmesg [10299.516344] saa7134 ALSA driver for DMA sound unloaded [11385.340661] Linux video capture interface: v2.00 [11385.384278] saa7130/34: v4l2 driver version 0.2.16 loaded [11385.384390] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [11385.384403] saa7130[0]: subsystem: 1131:0000, board: LifeView/Typhoon FlyVIDEO2000 [card=3,insmod option] [11385.384412] saa7130[0]: can't get MMIO memory @ 0x0 [11385.384431] saa7134: probe of 0000:01:07.0 failed with error -16 [11385.401174] saa7134 ALSA driver for DMA sound loaded [11385.401182] saa7134 ALSA: no saa7134 cards found [11477.797019] tvtime[12534]: segfault at 6b0 ip 0804cf64 sp bf928a4c error 4 in tvtime[8048000+76000] [11626.141821] tvtime[12549]: segfault at 6b0 ip 0804cf64 sp bfec357c error 4 in tvtime[8048000+76000] [12218.120632] saa7134 ALSA driver for DMA sound unloaded [12464.993061] Linux video capture interface: v2.00 [12465.028285] saa7130/34: v4l2 driver version 0.2.16 loaded [12465.028392] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [12465.028404] saa7134: <rant> [12465.028406] saa7134: Congratulations! Your TV card vendor saved a few [12465.028408] saa7134: cents for a eeprom, thus your pci board has no [12465.028411] saa7134: subsystem ID and I can't identify it automatically [12465.028414] saa7134: </rant> [12465.028416] saa7134: I feel better now. Ok, here are the good news: [12465.028418] saa7134: You can use the card=<nr> insmod option to specify [12465.028421] saa7134: which board do you have. The list: [12465.028428] saa7134: card=0 -> UNKNOWN/GENERIC [12465.028435] saa7134: card=1 -> Proteus Pro [philips reference design] 1131:2001 1131:2001 [12465.028447] saa7134: card=2 -> LifeView FlyVIDEO3000 5168:0138 4e42:0138 [12465.028457] saa7134: card=3 -> LifeView/Typhoon FlyVIDEO2000 5168:0138 4e42:0138 [12465.028467] saa7134: card=4 -> EMPRESS 1131:6752 [12465.028475] saa7134: card=5 -> SKNet Monster TV 1131:4e85 [12465.028484] saa7134: card=6 -> Tevion MD 9717 [12465.028491] saa7134: card=7 -> KNC One TV-Station RDS / Typhoon TV Tune 1131:fe01 1894:fe01 [12465.028501] saa7134: card=8 -> Terratec Cinergy 400 TV 153b:1142 [12465.028510] saa7134: card=9 -> Medion 5044 [12465.028517] saa7134: card=10 -> Kworld/KuroutoShikou SAA7130-TVPCI [12465.028523] saa7134: card=11 -> Terratec Cinergy 600 TV 153b:1143 [12465.028532] saa7134: card=12 -> Medion 7134 16be:0003 16be:5000 [12465.028542] saa7134: card=13 -> Typhoon TV+Radio 90031 [12465.028548] saa7134: card=14 -> ELSA EX-VISION 300TV 1048:226b [12465.028557] saa7134: card=15 -> ELSA EX-VISION 500TV 1048:226a [12465.028565] saa7134: card=16 -> ASUS TV-FM 7134 1043:4842 1043:4830 1043:4840 [12465.028576] saa7134: card=17 -> AOPEN VA1000 POWER 1131:7133 [12465.028585] saa7134: card=18 -> BMK MPEX No Tuner [12465.028592] saa7134: card=19 -> Compro VideoMate TV 185b:c100 [12465.028600] saa7134: card=20 -> Matrox CronosPlus 102b:48d0 [12465.028608] saa7134: card=21 -> 10MOONS PCI TV CAPTURE CARD 1131:2001 [12465.028617] saa7134: card=22 -> AverMedia M156 / Medion 2819 1461:a70b [12465.028625] saa7134: card=23 -> BMK MPEX Tuner [12465.028632] saa7134: card=24 -> KNC One TV-Station DVR 1894:a006 [12465.028640] saa7134: card=25 -> ASUS TV-FM 7133 1043:4843 [12465.028648] saa7134: card=26 -> Pinnacle PCTV Stereo (saa7134) 11bd:002b [12465.028657] saa7134: card=27 -> Manli MuchTV M-TV002 [12465.028663] saa7134: card=28 -> Manli MuchTV M-TV001 [12465.028670] saa7134: card=29 -> Nagase Sangyo TransGear 3000TV 1461:050c [12465.028679] saa7134: card=30 -> Elitegroup ECS TVP3XP FM1216 Tuner Card( 1019:4cb4 [12465.028687] saa7134: card=31 -> Elitegroup ECS TVP3XP FM1236 Tuner Card 1019:4cb5 [12465.028695] saa7134: card=32 -> AVACS SmartTV [12465.028702] saa7134: card=33 -> AVerMedia DVD EZMaker 1461:10ff [12465.028710] saa7134: card=34 -> Noval Prime TV 7133 [12465.028717] saa7134: card=35 -> AverMedia AverTV Studio 305 1461:2115 [12465.028725] saa7134: card=36 -> UPMOST PURPLE TV 12ab:0800 [12465.028734] saa7134: card=37 -> Items MuchTV Plus / IT-005 [12465.028740] saa7134: card=38 -> Terratec Cinergy 200 TV 153b:1152 [12465.028749] saa7134: card=39 -> LifeView FlyTV Platinum Mini 5168:0212 4e42:0212 5169:1502 [12465.028760] saa7134: card=40 -> Compro VideoMate TV PVR/FM 185b:c100 [12465.028768] saa7134: card=41 -> Compro VideoMate TV Gold+ 185b:c100 [12465.028776] saa7134: card=42 -> Sabrent SBT-TVFM (saa7130) [12465.028783] saa7134: card=43 -> :Zolid Xpert TV7134 [12465.028790] saa7134: card=44 -> Empire PCI TV-Radio LE [12465.028796] saa7134: card=45 -> Avermedia AVerTV Studio 307 1461:9715 [12465.028805] saa7134: card=46 -> AVerMedia Cardbus TV/Radio (E500) 1461:d6ee [12465.028813] saa7134: card=47 -> Terratec Cinergy 400 mobile 153b:1162 [12465.028821] saa7134: card=48 -> Terratec Cinergy 600 TV MK3 153b:1158 [12465.028830] saa7134: card=49 -> Compro VideoMate Gold+ Pal 185b:c200 [12465.028838] saa7134: card=50 -> Pinnacle PCTV 300i DVB-T + PAL 11bd:002d [12465.028847] saa7134: card=51 -> ProVideo PV952 1540:9524 [12465.028855] saa7134: card=52 -> AverMedia AverTV/305 1461:2108 [12465.028863] saa7134: card=53 -> ASUS TV-FM 7135 1043:4845 [12465.028871] saa7134: card=54 -> LifeView FlyTV Platinum FM / Gold 5168:0214 5168:5214 1489:0214 5168:0304 [12465.028884] saa7134: card=55 -> LifeView FlyDVB-T DUO / MSI TV@nywhere D 5168:0306 4e42:0306 [12465.028894] saa7134: card=56 -> Avermedia AVerTV 307 1461:a70a [12465.028903] saa7134: card=57 -> Avermedia AVerTV GO 007 FM 1461:f31f [12465.028911] saa7134: card=58 -> ADS Tech Instant TV (saa7135) 1421:0350 1421:0351 1421:0370 1421:1370 [12465.028924] saa7134: card=59 -> Kworld/Tevion V-Stream Xpert TV PVR7134 [12465.028931] saa7134: card=60 -> LifeView/Typhoon/Genius FlyDVB-T Duo Car 5168:0502 4e42:0502 1489:0502 [12465.028942] saa7134: card=61 -> Philips TOUGH DVB-T reference design 1131:2004 [12465.028951] saa7134: card=62 -> Compro VideoMate TV Gold+II [12465.028958] saa7134: card=63 -> Kworld Xpert TV PVR7134 [12465.028964] saa7134: card=64 -> FlyTV mini Asus Digimatrix 1043:0210 [12465.028973] saa7134: card=65 -> V-Stream Studio TV Terminator [12465.028980] saa7134: card=66 -> Yuan TUN-900 (saa7135) [12465.028986] saa7134: card=67 -> Beholder BeholdTV 409 FM 0000:4091 [12465.028995] saa7134: card=68 -> GoTView 7135 PCI 5456:7135 [12465.029003] saa7134: card=69 -> Philips EUROPA V3 reference design 1131:2004 [12465.029011] saa7134: card=70 -> Compro Videomate DVB-T300 185b:c900 [12465.029020] saa7134: card=71 -> Compro Videomate DVB-T200 185b:c901 [12465.029028] saa7134: card=72 -> RTD Embedded Technologies VFG7350 1435:7350 [12465.029036] saa7134: card=73 -> RTD Embedded Technologies VFG7330 1435:7330 [12465.029045] saa7134: card=74 -> LifeView FlyTV Platinum Mini2 14c0:1212 [12465.029053] saa7134: card=75 -> AVerMedia AVerTVHD MCE A180 1461:1044 [12465.029062] saa7134: card=76 -> SKNet MonsterTV Mobile 1131:4ee9 [12465.029070] saa7134: card=77 -> Pinnacle PCTV 40i/50i/110i (saa7133) 11bd:002e [12465.029078] saa7134: card=78 -> ASUSTeK P7131 Dual 1043:4862 [12465.029087] saa7134: card=79 -> Sedna/MuchTV PC TV Cardbus TV/Radio (ITO [12465.029094] saa7134: card=80 -> ASUS Digimatrix TV 1043:0210 [12465.029102] saa7134: card=81 -> Philips Tiger reference design 1131:2018 [12465.029110] saa7134: card=82 -> MSI TV@Anywhere plus 1462:6231 1462:8624 [12465.029120] saa7134: card=83 -> Terratec Cinergy 250 PCI TV 153b:1160 [12465.029128] saa7134: card=84 -> LifeView FlyDVB Trio 5168:0319 [12465.029137] saa7134: card=85 -> AverTV DVB-T 777 1461:2c05 1461:2c05 [12465.029147] saa7134: card=86 -> LifeView FlyDVB-T / Genius VideoWonder D 5168:0301 1489:0301 [12465.029156] saa7134: card=87 -> ADS Instant TV Duo Cardbus PTV331 0331:1421 [12465.029165] saa7134: card=88 -> Tevion/KWorld DVB-T 220RF 17de:7201 [12465.029173] saa7134: card=89 -> ELSA EX-VISION 700TV 1048:226c [12465.029182] saa7134: card=90 -> Kworld ATSC110/115 17de:7350 17de:7352 [12465.029191] saa7134: card=91 -> AVerMedia A169 B 1461:7360 [12465.029200] saa7134: card=92 -> AVerMedia A169 B1 1461:6360 [12465.029208] saa7134: card=93 -> Medion 7134 Bridge #2 16be:0005 [12465.029216] saa7134: card=94 -> LifeView FlyDVB-T Hybrid Cardbus/MSI TV 5168:3306 5168:3502 5168:3307 4e42:3502 [12465.029229] saa7134: card=95 -> LifeView FlyVIDEO3000 (NTSC) 5169:0138 [12465.029238] saa7134: card=96 -> Medion Md8800 Quadro 16be:0007 16be:0008 16be:000d [12465.029249] saa7134: card=97 -> LifeView FlyDVB-S /Acorp TV134DS 5168:0300 4e42:0300 [12465.029259] saa7134: card=98 -> Proteus Pro 2309 0919:2003 [12465.029267] saa7134: card=99 -> AVerMedia TV Hybrid A16AR 1461:2c00 [12465.029276] saa7134: card=100 -> Asus Europa2 OEM 1043:4860 [12465.029284] saa7134: card=101 -> Pinnacle PCTV 310i 11bd:002f [12465.029293] saa7134: card=102 -> Avermedia AVerTV Studio 507 1461:9715 [12465.029301] saa7134: card=103 -> Compro Videomate DVB-T200A [12465.029308] saa7134: card=104 -> Hauppauge WinTV-HVR1110 DVB-T/Hybrid 0070:6700 0070:6701 0070:6702 0070:6703 0070:6704 0070:6705 [12465.029324] saa7134: card=105 -> Terratec Cinergy HT PCMCIA 153b:1172 [12465.029332] saa7134: card=106 -> Encore ENLTV 1131:2342 1131:2341 3016:2344 [12465.029344] saa7134: card=107 -> Encore ENLTV-FM 1131:230f [12465.029352] saa7134: card=108 -> Terratec Cinergy HT PCI 153b:1175 [12465.029360] saa7134: card=109 -> Philips Tiger - S Reference design [12465.029367] saa7134: card=110 -> Avermedia M102 1461:f31e [12465.029375] saa7134: card=111 -> ASUS P7131 4871 1043:4871 [12465.029384] saa7134: card=112 -> ASUSTeK P7131 Hybrid 1043:4876 [12465.029392] saa7134: card=113 -> Elitegroup ECS TVP3XP FM1246 Tuner Card 1019:4cb6 [12465.029401] saa7134: card=114 -> KWorld DVB-T 210 17de:7250 [12465.029409] saa7134: card=115 -> Sabrent PCMCIA TV-PCB05 0919:2003 [12465.029418] saa7134: card=116 -> 10MOONS TM300 TV Card 1131:2304 [12465.029426] saa7134: card=117 -> Avermedia Super 007 1461:f01d [12465.029435] saa7134: card=118 -> Beholder BeholdTV 401 0000:4016 [12465.029443] saa7134: card=119 -> Beholder BeholdTV 403 0000:4036 [12465.029451] saa7134: card=120 -> Beholder BeholdTV 403 FM 0000:4037 [12465.029459] saa7134: card=121 -> Beholder BeholdTV 405 0000:4050 [12465.029468] saa7134: card=122 -> Beholder BeholdTV 405 FM 0000:4051 [12465.029476] saa7134: card=123 -> Beholder BeholdTV 407 0000:4070 [12465.029484] saa7134: card=124 -> Beholder BeholdTV 407 FM 0000:4071 [12465.029493] saa7134: card=125 -> Beholder BeholdTV 409 0000:4090 [12465.029501] saa7134: card=126 -> Beholder BeholdTV 505 FM 5ace:5050 [12465.029510] saa7134: card=127 -> Beholder BeholdTV 507 FM / BeholdTV 509 5ace:5070 5ace:5090 [12465.029520] saa7134: card=128 -> Beholder BeholdTV Columbus TVFM 0000:5201 [12465.029528] saa7134: card=129 -> Beholder BeholdTV 607 FM 5ace:6070 [12465.029537] saa7134: card=130 -> Beholder BeholdTV M6 5ace:6190 [12465.029545] saa7134: card=131 -> Twinhan Hybrid DTV-DVB 3056 PCI 1822:0022 [12465.029554] saa7134: card=132 -> Genius TVGO AM11MCE [12465.029560] saa7134: card=133 -> NXP Snake DVB-S reference design [12465.029567] saa7134: card=134 -> Medion/Creatix CTX953 Hybrid 16be:0010 [12465.029576] saa7134: card=135 -> MSI TV@nywhere A/D v1.1 1462:8625 [12465.029584] saa7134: card=136 -> AVerMedia Cardbus TV/Radio (E506R) 1461:f436 [12465.029592] saa7134: card=137 -> AVerMedia Hybrid TV/Radio (A16D) 1461:f936 [12465.029601] saa7134: card=138 -> Avermedia M115 1461:a836 [12465.029609] saa7134: card=139 -> Compro VideoMate T750 185b:c900 [12465.029617] saa7134: card=140 -> Avermedia DVB-S Pro A700 1461:a7a1 [12465.029626] saa7134: card=141 -> Avermedia DVB-S Hybrid+FM A700 1461:a7a2 [12465.029634] saa7134: card=142 -> Beholder BeholdTV H6 5ace:6290 [12465.029642] saa7134: card=143 -> Beholder BeholdTV M63 5ace:6191 [12465.029651] saa7134: card=144 -> Beholder BeholdTV M6 Extra 5ace:6193 [12465.029659] saa7134: card=145 -> AVerMedia MiniPCI DVB-T Hybrid M103 1461:f636 1461:f736 [12465.029669] saa7134: card=146 -> ASUSTeK P7131 Analog [12465.029676] saa7134: card=147 -> Asus Tiger 3in1 1043:4878 [12465.029684] saa7134: card=148 -> Encore ENLTV-FM v5.3 1a7f:2008 [12465.029693] saa7134: card=149 -> Avermedia PCI pure analog (M135A) 1461:f11d [12465.029701] saa7134: card=150 -> Zogis Real Angel 220 [12465.029708] saa7134: card=151 -> ADS Tech Instant HDTV 1421:0380 [12465.029716] saa7134: card=152 -> Asus Tiger Rev:1.00 1043:4857 [12465.029725] saa7134: card=153 -> Kworld Plus TV Analog Lite PCI 17de:7128 [12465.029733] saa7134: card=154 -> Avermedia AVerTV GO 007 FM Plus 1461:f31d [12465.029742] saa7134: card=155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid 0070:6706 0070:6708 [12465.029752] saa7134: card=156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid 0070:6707 0070:6709 0070:670a [12465.029763] saa7134: card=157 -> Avermedia AVerTV Studio 507UA 1461:a11b [12465.029772] saa7134: card=158 -> AVerMedia Cardbus TV/Radio (E501R) 1461:b7e9 [12465.029780] saa7134: card=159 -> Beholder BeholdTV 505 RDS 0000:505b [12465.029789] saa7134: card=160 -> Beholder BeholdTV 507 RDS 0000:5071 [12465.029797] saa7134: card=161 -> Beholder BeholdTV 507 RDS 0000:507b [12465.029806] saa7134: card=162 -> Beholder BeholdTV 607 FM 5ace:6071 [12465.029815] saa7134: card=163 -> Beholder BeholdTV 609 FM 5ace:6090 [12465.029823] saa7134: card=164 -> Beholder BeholdTV 609 FM 5ace:6091 [12465.029832] saa7134: card=165 -> Beholder BeholdTV 607 RDS 5ace:6072 [12465.029840] saa7134: card=166 -> Beholder BeholdTV 607 RDS 5ace:6073 [12465.029849] saa7134: card=167 -> Beholder BeholdTV 609 RDS 5ace:6092 [12465.029857] saa7134: card=168 -> Beholder BeholdTV 609 RDS 5ace:6093 [12465.029866] saa7134: card=169 -> Compro VideoMate S350/S300 185b:c900 [12465.029874] saa7134: card=170 -> AverMedia AverTV Studio 505 1461:a115 [12465.029883] saa7134: card=171 -> Beholder BeholdTV X7 5ace:7595 [12465.029892] saa7134: card=172 -> RoverMedia TV Link Pro FM 19d1:0138 [12465.029900] saa7134: card=173 -> Zolid Hybrid TV Tuner PCI 1131:2004 [12465.029909] saa7134: card=174 -> Asus Europa Hybrid OEM 1043:4847 [12465.029917] saa7134: card=175 -> Leadtek Winfast DTV1000S 107d:6655 [12465.029926] saa7134: card=176 -> Beholder BeholdTV 505 RDS 0000:5051 [12465.029934] saa7134: card=177 -> Hawell HW-404M7 [12465.029941] saa7134: card=178 -> Beholder BeholdTV H7 [12465.029948] saa7134: card=179 -> Beholder BeholdTV A7 [12465.029955] saa7134: card=180 -> Avermedia PCI M733A 1461:4155 1461:4255 [12465.029967] saa7130[0]: subsystem: 1131:0000, board: UNKNOWN/GENERIC [card=0,autodetected] [12465.030033] saa7130[0]: can't get MMIO memory @ 0x0 [12465.030051] saa7134: probe of 0000:01:07.0 failed with error -16 [12465.053892] saa7134 ALSA driver for DMA sound loaded [12465.053900] saa7134 ALSA: no saa7134 cards found tvtime-scanner Leyendo la configuración de /etc/tvtime/tvtime.xml Leyendo la configuración de /home/ricardo/.tvtime/tvtime.xml Escaneando usando la norma de TV NTSC. /home/ricardo/.tvtime/stationlist.xml: No existing NTSC station list "Custom". videoinput: Cannot open capture device /dev/video0: No existe el dispositivo o la dirección

  Read the article

• Problems with capture TV card

  - by user8270

  Hi, I have a TV card that I have not managed to install with Ubuntu 10.10 i386. I have tried various topics in various forums and I could not install it. I hope you can help me to install it thank you. lspci 01:07.0 Multimedia controller: Philips Semiconductors SAA7130 Video Broadcast Decoder (rev 01) dmesg [10299.516344] saa7134 ALSA driver for DMA sound unloaded [11385.340661] Linux video capture interface: v2.00 [11385.384278] saa7130/34: v4l2 driver version 0.2.16 loaded [11385.384390] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [11385.384403] saa7130[0]: subsystem: 1131:0000, board: LifeView/Typhoon FlyVIDEO2000 [card=3,insmod option] [11385.384412] saa7130[0]: can't get MMIO memory @ 0x0 [11385.384431] saa7134: probe of 0000:01:07.0 failed with error -16 [11385.401174] saa7134 ALSA driver for DMA sound loaded [11385.401182] saa7134 ALSA: no saa7134 cards found [11477.797019] tvtime[12534]: segfault at 6b0 ip 0804cf64 sp bf928a4c error 4 in tvtime[8048000+76000] [11626.141821] tvtime[12549]: segfault at 6b0 ip 0804cf64 sp bfec357c error 4 in tvtime[8048000+76000] [12218.120632] saa7134 ALSA driver for DMA sound unloaded [12464.993061] Linux video capture interface: v2.00 [12465.028285] saa7130/34: v4l2 driver version 0.2.16 loaded [12465.028392] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [12465.028404] saa7134: <rant> [12465.028406] saa7134: Congratulations! Your TV card vendor saved a few [12465.028408] saa7134: cents for a eeprom, thus your pci board has no [12465.028411] saa7134: subsystem ID and I can't identify it automatically [12465.028414] saa7134: </rant> [12465.028416] saa7134: I feel better now. Ok, here are the good news: [12465.028418] saa7134: You can use the card=<nr> insmod option to specify [12465.028421] saa7134: which board do you have. The list: [12465.028428] saa7134: card=0 -> UNKNOWN/GENERIC [12465.028435] saa7134: card=1 -> Proteus Pro [philips reference design] 1131:2001 1131:2001 [12465.028447] saa7134: card=2 -> LifeView FlyVIDEO3000 5168:0138 4e42:0138 [12465.028457] saa7134: card=3 -> LifeView/Typhoon FlyVIDEO2000 5168:0138 4e42:0138 [12465.028467] saa7134: card=4 -> EMPRESS 1131:6752 [12465.028475] saa7134: card=5 -> SKNet Monster TV 1131:4e85 [12465.028484] saa7134: card=6 -> Tevion MD 9717 [12465.028491] saa7134: card=7 -> KNC One TV-Station RDS / Typhoon TV Tune 1131:fe01 1894:fe01 [12465.028501] saa7134: card=8 -> Terratec Cinergy 400 TV 153b:1142 [12465.028510] saa7134: card=9 -> Medion 5044 [12465.028517] saa7134: card=10 -> Kworld/KuroutoShikou SAA7130-TVPCI [12465.028523] saa7134: card=11 -> Terratec Cinergy 600 TV 153b:1143 [12465.028532] saa7134: card=12 -> Medion 7134 16be:0003 16be:5000 [12465.028542] saa7134: card=13 -> Typhoon TV+Radio 90031 [12465.028548] saa7134: card=14 -> ELSA EX-VISION 300TV 1048:226b [12465.028557] saa7134: card=15 -> ELSA EX-VISION 500TV 1048:226a [12465.028565] saa7134: card=16 -> ASUS TV-FM 7134 1043:4842 1043:4830 1043:4840 [12465.028576] saa7134: card=17 -> AOPEN VA1000 POWER 1131:7133 [12465.028585] saa7134: card=18 -> BMK MPEX No Tuner [12465.028592] saa7134: card=19 -> Compro VideoMate TV 185b:c100 [12465.028600] saa7134: card=20 -> Matrox CronosPlus 102b:48d0 [12465.028608] saa7134: card=21 -> 10MOONS PCI TV CAPTURE CARD 1131:2001 [12465.028617] saa7134: card=22 -> AverMedia M156 / Medion 2819 1461:a70b [12465.028625] saa7134: card=23 -> BMK MPEX Tuner [12465.028632] saa7134: card=24 -> KNC One TV-Station DVR 1894:a006 [12465.028640] saa7134: card=25 -> ASUS TV-FM 7133 1043:4843 [12465.028648] saa7134: card=26 -> Pinnacle PCTV Stereo (saa7134) 11bd:002b [12465.028657] saa7134: card=27 -> Manli MuchTV M-TV002 [12465.028663] saa7134: card=28 -> Manli MuchTV M-TV001 [12465.028670] saa7134: card=29 -> Nagase Sangyo TransGear 3000TV 1461:050c [12465.028679] saa7134: card=30 -> Elitegroup ECS TVP3XP FM1216 Tuner Card( 1019:4cb4 [12465.028687] saa7134: card=31 -> Elitegroup ECS TVP3XP FM1236 Tuner Card 1019:4cb5 [12465.028695] saa7134: card=32 -> AVACS SmartTV [12465.028702] saa7134: card=33 -> AVerMedia DVD EZMaker 1461:10ff [12465.028710] saa7134: card=34 -> Noval Prime TV 7133 [12465.028717] saa7134: card=35 -> AverMedia AverTV Studio 305 1461:2115 [12465.028725] saa7134: card=36 -> UPMOST PURPLE TV 12ab:0800 [12465.028734] saa7134: card=37 -> Items MuchTV Plus / IT-005 [12465.028740] saa7134: card=38 -> Terratec Cinergy 200 TV 153b:1152 [12465.028749] saa7134: card=39 -> LifeView FlyTV Platinum Mini 5168:0212 4e42:0212 5169:1502 [12465.028760] saa7134: card=40 -> Compro VideoMate TV PVR/FM 185b:c100 [12465.028768] saa7134: card=41 -> Compro VideoMate TV Gold+ 185b:c100 [12465.028776] saa7134: card=42 -> Sabrent SBT-TVFM (saa7130) [12465.028783] saa7134: card=43 -> :Zolid Xpert TV7134 [12465.028790] saa7134: card=44 -> Empire PCI TV-Radio LE [12465.028796] saa7134: card=45 -> Avermedia AVerTV Studio 307 1461:9715 [12465.028805] saa7134: card=46 -> AVerMedia Cardbus TV/Radio (E500) 1461:d6ee [12465.028813] saa7134: card=47 -> Terratec Cinergy 400 mobile 153b:1162 [12465.028821] saa7134: card=48 -> Terratec Cinergy 600 TV MK3 153b:1158 [12465.028830] saa7134: card=49 -> Compro VideoMate Gold+ Pal 185b:c200 [12465.028838] saa7134: card=50 -> Pinnacle PCTV 300i DVB-T + PAL 11bd:002d [12465.028847] saa7134: card=51 -> ProVideo PV952 1540:9524 [12465.028855] saa7134: card=52 -> AverMedia AverTV/305 1461:2108 [12465.028863] saa7134: card=53 -> ASUS TV-FM 7135 1043:4845 [12465.028871] saa7134: card=54 -> LifeView FlyTV Platinum FM / Gold 5168:0214 5168:5214 1489:0214 5168:0304 [12465.028884] saa7134: card=55 -> LifeView FlyDVB-T DUO / MSI TV@nywhere D 5168:0306 4e42:0306 [12465.028894] saa7134: card=56 -> Avermedia AVerTV 307 1461:a70a [12465.028903] saa7134: card=57 -> Avermedia AVerTV GO 007 FM 1461:f31f [12465.028911] saa7134: card=58 -> ADS Tech Instant TV (saa7135) 1421:0350 1421:0351 1421:0370 1421:1370 [12465.028924] saa7134: card=59 -> Kworld/Tevion V-Stream Xpert TV PVR7134 [12465.028931] saa7134: card=60 -> LifeView/Typhoon/Genius FlyDVB-T Duo Car 5168:0502 4e42:0502 1489:0502 [12465.028942] saa7134: card=61 -> Philips TOUGH DVB-T reference design 1131:2004 [12465.028951] saa7134: card=62 -> Compro VideoMate TV Gold+II [12465.028958] saa7134: card=63 -> Kworld Xpert TV PVR7134 [12465.028964] saa7134: card=64 -> FlyTV mini Asus Digimatrix 1043:0210 [12465.028973] saa7134: card=65 -> V-Stream Studio TV Terminator [12465.028980] saa7134: card=66 -> Yuan TUN-900 (saa7135) [12465.028986] saa7134: card=67 -> Beholder BeholdTV 409 FM 0000:4091 [12465.028995] saa7134: card=68 -> GoTView 7135 PCI 5456:7135 [12465.029003] saa7134: card=69 -> Philips EUROPA V3 reference design 1131:2004 [12465.029011] saa7134: card=70 -> Compro Videomate DVB-T300 185b:c900 [12465.029020] saa7134: card=71 -> Compro Videomate DVB-T200 185b:c901 [12465.029028] saa7134: card=72 -> RTD Embedded Technologies VFG7350 1435:7350 [12465.029036] saa7134: card=73 -> RTD Embedded Technologies VFG7330 1435:7330 [12465.029045] saa7134: card=74 -> LifeView FlyTV Platinum Mini2 14c0:1212 [12465.029053] saa7134: card=75 -> AVerMedia AVerTVHD MCE A180 1461:1044 [12465.029062] saa7134: card=76 -> SKNet MonsterTV Mobile 1131:4ee9 [12465.029070] saa7134: card=77 -> Pinnacle PCTV 40i/50i/110i (saa7133) 11bd:002e [12465.029078] saa7134: card=78 -> ASUSTeK P7131 Dual 1043:4862 [12465.029087] saa7134: card=79 -> Sedna/MuchTV PC TV Cardbus TV/Radio (ITO [12465.029094] saa7134: card=80 -> ASUS Digimatrix TV 1043:0210 [12465.029102] saa7134: card=81 -> Philips Tiger reference design 1131:2018 [12465.029110] saa7134: card=82 -> MSI TV@Anywhere plus 1462:6231 1462:8624 [12465.029120] saa7134: card=83 -> Terratec Cinergy 250 PCI TV 153b:1160 [12465.029128] saa7134: card=84 -> LifeView FlyDVB Trio 5168:0319 [12465.029137] saa7134: card=85 -> AverTV DVB-T 777 1461:2c05 1461:2c05 [12465.029147] saa7134: card=86 -> LifeView FlyDVB-T / Genius VideoWonder D 5168:0301 1489:0301 [12465.029156] saa7134: card=87 -> ADS Instant TV Duo Cardbus PTV331 0331:1421 [12465.029165] saa7134: card=88 -> Tevion/KWorld DVB-T 220RF 17de:7201 [12465.029173] saa7134: card=89 -> ELSA EX-VISION 700TV 1048:226c [12465.029182] saa7134: card=90 -> Kworld ATSC110/115 17de:7350 17de:7352 [12465.029191] saa7134: card=91 -> AVerMedia A169 B 1461:7360 [12465.029200] saa7134: card=92 -> AVerMedia A169 B1 1461:6360 [12465.029208] saa7134: card=93 -> Medion 7134 Bridge #2 16be:0005 [12465.029216] saa7134: card=94 -> LifeView FlyDVB-T Hybrid Cardbus/MSI TV 5168:3306 5168:3502 5168:3307 4e42:3502 [12465.029229] saa7134: card=95 -> LifeView FlyVIDEO3000 (NTSC) 5169:0138 [12465.029238] saa7134: card=96 -> Medion Md8800 Quadro 16be:0007 16be:0008 16be:000d [12465.029249] saa7134: card=97 -> LifeView FlyDVB-S /Acorp TV134DS 5168:0300 4e42:0300 [12465.029259] saa7134: card=98 -> Proteus Pro 2309 0919:2003 [12465.029267] saa7134: card=99 -> AVerMedia TV Hybrid A16AR 1461:2c00 [12465.029276] saa7134: card=100 -> Asus Europa2 OEM 1043:4860 [12465.029284] saa7134: card=101 -> Pinnacle PCTV 310i 11bd:002f [12465.029293] saa7134: card=102 -> Avermedia AVerTV Studio 507 1461:9715 [12465.029301] saa7134: card=103 -> Compro Videomate DVB-T200A [12465.029308] saa7134: card=104 -> Hauppauge WinTV-HVR1110 DVB-T/Hybrid 0070:6700 0070:6701 0070:6702 0070:6703 0070:6704 0070:6705 [12465.029324] saa7134: card=105 -> Terratec Cinergy HT PCMCIA 153b:1172 [12465.029332] saa7134: card=106 -> Encore ENLTV 1131:2342 1131:2341 3016:2344 [12465.029344] saa7134: card=107 -> Encore ENLTV-FM 1131:230f [12465.029352] saa7134: card=108 -> Terratec Cinergy HT PCI 153b:1175 [12465.029360] saa7134: card=109 -> Philips Tiger - S Reference design [12465.029367] saa7134: card=110 -> Avermedia M102 1461:f31e [12465.029375] saa7134: card=111 -> ASUS P7131 4871 1043:4871 [12465.029384] saa7134: card=112 -> ASUSTeK P7131 Hybrid 1043:4876 [12465.029392] saa7134: card=113 -> Elitegroup ECS TVP3XP FM1246 Tuner Card 1019:4cb6 [12465.029401] saa7134: card=114 -> KWorld DVB-T 210 17de:7250 [12465.029409] saa7134: card=115 -> Sabrent PCMCIA TV-PCB05 0919:2003 [12465.029418] saa7134: card=116 -> 10MOONS TM300 TV Card 1131:2304 [12465.029426] saa7134: card=117 -> Avermedia Super 007 1461:f01d [12465.029435] saa7134: card=118 -> Beholder BeholdTV 401 0000:4016 [12465.029443] saa7134: card=119 -> Beholder BeholdTV 403 0000:4036 [12465.029451] saa7134: card=120 -> Beholder BeholdTV 403 FM 0000:4037 [12465.029459] saa7134: card=121 -> Beholder BeholdTV 405 0000:4050 [12465.029468] saa7134: card=122 -> Beholder BeholdTV 405 FM 0000:4051 [12465.029476] saa7134: card=123 -> Beholder BeholdTV 407 0000:4070 [12465.029484] saa7134: card=124 -> Beholder BeholdTV 407 FM 0000:4071 [12465.029493] saa7134: card=125 -> Beholder BeholdTV 409 0000:4090 [12465.029501] saa7134: card=126 -> Beholder BeholdTV 505 FM 5ace:5050 [12465.029510] saa7134: card=127 -> Beholder BeholdTV 507 FM / BeholdTV 509 5ace:5070 5ace:5090 [12465.029520] saa7134: card=128 -> Beholder BeholdTV Columbus TVFM 0000:5201 [12465.029528] saa7134: card=129 -> Beholder BeholdTV 607 FM 5ace:6070 [12465.029537] saa7134: card=130 -> Beholder BeholdTV M6 5ace:6190 [12465.029545] saa7134: card=131 -> Twinhan Hybrid DTV-DVB 3056 PCI 1822:0022 [12465.029554] saa7134: card=132 -> Genius TVGO AM11MCE [12465.029560] saa7134: card=133 -> NXP Snake DVB-S reference design [12465.029567] saa7134: card=134 -> Medion/Creatix CTX953 Hybrid 16be:0010 [12465.029576] saa7134: card=135 -> MSI TV@nywhere A/D v1.1 1462:8625 [12465.029584] saa7134: card=136 -> AVerMedia Cardbus TV/Radio (E506R) 1461:f436 [12465.029592] saa7134: card=137 -> AVerMedia Hybrid TV/Radio (A16D) 1461:f936 [12465.029601] saa7134: card=138 -> Avermedia M115 1461:a836 [12465.029609] saa7134: card=139 -> Compro VideoMate T750 185b:c900 [12465.029617] saa7134: card=140 -> Avermedia DVB-S Pro A700 1461:a7a1 [12465.029626] saa7134: card=141 -> Avermedia DVB-S Hybrid+FM A700 1461:a7a2 [12465.029634] saa7134: card=142 -> Beholder BeholdTV H6 5ace:6290 [12465.029642] saa7134: card=143 -> Beholder BeholdTV M63 5ace:6191 [12465.029651] saa7134: card=144 -> Beholder BeholdTV M6 Extra 5ace:6193 [12465.029659] saa7134: card=145 -> AVerMedia MiniPCI DVB-T Hybrid M103 1461:f636 1461:f736 [12465.029669] saa7134: card=146 -> ASUSTeK P7131 Analog [12465.029676] saa7134: card=147 -> Asus Tiger 3in1 1043:4878 [12465.029684] saa7134: card=148 -> Encore ENLTV-FM v5.3 1a7f:2008 [12465.029693] saa7134: card=149 -> Avermedia PCI pure analog (M135A) 1461:f11d [12465.029701] saa7134: card=150 -> Zogis Real Angel 220 [12465.029708] saa7134: card=151 -> ADS Tech Instant HDTV 1421:0380 [12465.029716] saa7134: card=152 -> Asus Tiger Rev:1.00 1043:4857 [12465.029725] saa7134: card=153 -> Kworld Plus TV Analog Lite PCI 17de:7128 [12465.029733] saa7134: card=154 -> Avermedia AVerTV GO 007 FM Plus 1461:f31d [12465.029742] saa7134: card=155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid 0070:6706 0070:6708 [12465.029752] saa7134: card=156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid 0070:6707 0070:6709 0070:670a [12465.029763] saa7134: card=157 -> Avermedia AVerTV Studio 507UA 1461:a11b [12465.029772] saa7134: card=158 -> AVerMedia Cardbus TV/Radio (E501R) 1461:b7e9 [12465.029780] saa7134: card=159 -> Beholder BeholdTV 505 RDS 0000:505b [12465.029789] saa7134: card=160 -> Beholder BeholdTV 507 RDS 0000:5071 [12465.029797] saa7134: card=161 -> Beholder BeholdTV 507 RDS 0000:507b [12465.029806] saa7134: card=162 -> Beholder BeholdTV 607 FM 5ace:6071 [12465.029815] saa7134: card=163 -> Beholder BeholdTV 609 FM 5ace:6090 [12465.029823] saa7134: card=164 -> Beholder BeholdTV 609 FM 5ace:6091 [12465.029832] saa7134: card=165 -> Beholder BeholdTV 607 RDS 5ace:6072 [12465.029840] saa7134: card=166 -> Beholder BeholdTV 607 RDS 5ace:6073 [12465.029849] saa7134: card=167 -> Beholder BeholdTV 609 RDS 5ace:6092 [12465.029857] saa7134: card=168 -> Beholder BeholdTV 609 RDS 5ace:6093 [12465.029866] saa7134: card=169 -> Compro VideoMate S350/S300 185b:c900 [12465.029874] saa7134: card=170 -> AverMedia AverTV Studio 505 1461:a115 [12465.029883] saa7134: card=171 -> Beholder BeholdTV X7 5ace:7595 [12465.029892] saa7134: card=172 -> RoverMedia TV Link Pro FM 19d1:0138 [12465.029900] saa7134: card=173 -> Zolid Hybrid TV Tuner PCI 1131:2004 [12465.029909] saa7134: card=174 -> Asus Europa Hybrid OEM 1043:4847 [12465.029917] saa7134: card=175 -> Leadtek Winfast DTV1000S 107d:6655 [12465.029926] saa7134: card=176 -> Beholder BeholdTV 505 RDS 0000:5051 [12465.029934] saa7134: card=177 -> Hawell HW-404M7 [12465.029941] saa7134: card=178 -> Beholder BeholdTV H7 [12465.029948] saa7134: card=179 -> Beholder BeholdTV A7 [12465.029955] saa7134: card=180 -> Avermedia PCI M733A 1461:4155 1461:4255 [12465.029967] saa7130[0]: subsystem: 1131:0000, board: UNKNOWN/GENERIC [card=0,autodetected] [12465.030033] saa7130[0]: can't get MMIO memory @ 0x0 [12465.030051] saa7134: probe of 0000:01:07.0 failed with error -16 [12465.053892] saa7134 ALSA driver for DMA sound loaded [12465.053900] saa7134 ALSA: no saa7134 cards found tvtime-scanner Leyendo la configuración de /etc/tvtime/tvtime.xml Leyendo la configuración de /home/ricardo/.tvtime/tvtime.xml Escaneando usando la norma de TV NTSC. /home/ricardo/.tvtime/stationlist.xml: No existing NTSC station list "Custom". videoinput: Cannot open capture device /dev/video0: No existe el dispositivo o la dirección ls /dev/ No video directory here

  Read the article

• Wireless card power management

  - by penner

  I have noticed that when my computer in plugged in, the wireless strength increases. I'm assuming this is to do with power management. Is there a way to disable Wireless Power Management? I have found a few blog posts that show hacks to disable this but what is best practice here? Should there not be an option via the power menu that lets you toggle this? EDIT -- FILES AND LOGS AS REQUESTED /var/log/kern.log Jul 11 11:45:27 CoolBreeze kernel: [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532080] [fglrx] Gart USWC size:1280 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532084] [fglrx] Gart cacheable size:508 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Jul 11 11:45:38 CoolBreeze kernel: [ 17.423743] eth1: no IPv6 routers present Jul 11 11:46:37 CoolBreeze kernel: [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) Jul 11 11:46:37 CoolBreeze kernel: [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 Jul 11 11:54:25 CoolBreeze kernel: [ 543.679614] eth1: no IPv6 routers present dmesg [ 1.411959] ACPI: Power Button [PWRB] [ 1.412046] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 1.412054] ACPI: Sleep Button [SLPB] [ 1.412150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 1.412765] ACPI: Lid Switch [LID0] [ 1.412866] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.412874] ACPI: Power Button [PWRF] [ 1.412996] ACPI: Fan [FAN0] (off) [ 1.413068] ACPI: Fan [FAN1] (off) [ 1.419493] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.419498] ACPI: Thermal Zone [TZ00] (27 C) [ 1.421913] thermal LNXTHERM:01: registered as thermal_zone1 [ 1.421918] ACPI: Thermal Zone [TZ01] (61 C) [ 1.421971] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.421986] ACPI: Battery Slot [BAT0] (battery present) [ 1.422062] ERST: Table is not found! [ 1.422067] GHES: HEST is not enabled! [ 1.422158] isapnp: Scanning for PnP cards... [ 1.422242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.434620] ACPI: Battery Slot [BAT0] (battery present) [ 1.736355] Freeing initrd memory: 14352k freed [ 1.777846] isapnp: No Plug & Play device found [ 1.963650] Linux agpgart interface v0.103 [ 1.967148] brd: module loaded [ 1.968866] loop: module loaded [ 1.969134] ahci 0000:00:1f.2: version 3.0 [ 1.969154] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.969226] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X [ 1.969277] ahci: SSS flag set, parallel bus scan disabled [ 1.969320] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x23 impl SATA mode [ 1.969329] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst [ 1.969338] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.983340] scsi0 : ahci [ 1.983515] scsi1 : ahci [ 1.983670] scsi2 : ahci [ 1.983829] scsi3 : ahci [ 1.983985] scsi4 : ahci [ 1.984145] scsi5 : ahci [ 1.984270] ata1: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005100 irq 45 [ 1.984277] ata2: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005180 irq 45 [ 1.984282] ata3: DUMMY [ 1.984285] ata4: DUMMY [ 1.984288] ata5: DUMMY [ 1.984292] ata6: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005380 irq 45 [ 1.985150] Fixed MDIO Bus: probed [ 1.985192] tun: Universal TUN/TAP device driver, 1.6 [ 1.985196] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 1.985285] PPP generic driver version 2.4.2 [ 1.985472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.985507] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.985534] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 1.985541] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 1.985626] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.985666] ehci_hcd 0000:00:1a.0: debug port 2 [ 1.989663] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 1.989690] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf1005800 [ 2.002183] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.002447] hub 1-0:1.0: USB hub found [ 2.002455] hub 1-0:1.0: 3 ports detected [ 2.002607] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.002633] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.002639] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 2.002737] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.002775] ehci_hcd 0000:00:1d.0: debug port 2 [ 2.006780] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 2.006806] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf1005c00 [ 2.022161] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.022401] hub 2-0:1.0: USB hub found [ 2.022409] hub 2-0:1.0: 3 ports detected [ 2.022567] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.022599] uhci_hcd: USB Universal Host Controller Interface driver [ 2.022720] usbcore: registered new interface driver libusual [ 2.022813] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.035831] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.035844] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.036096] mousedev: PS/2 mouse device common for all mice [ 2.036710] rtc_cmos 00:07: RTC can wake from S4 [ 2.036881] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 [ 2.037143] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 2.037503] device-mapper: uevent: version 1.0.3 [ 2.037656] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.037725] EISA: Probing bus 0 at eisa.0 [ 2.037729] EISA: Cannot allocate resource for mainboard [ 2.037734] Cannot allocate resource for EISA slot 1 [ 2.037738] Cannot allocate resource for EISA slot 2 [ 2.037741] Cannot allocate resource for EISA slot 3 [ 2.037745] Cannot allocate resource for EISA slot 4 [ 2.037749] Cannot allocate resource for EISA slot 5 [ 2.037753] Cannot allocate resource for EISA slot 6 [ 2.037756] Cannot allocate resource for EISA slot 7 [ 2.037760] Cannot allocate resource for EISA slot 8 [ 2.037764] EISA: Detected 0 cards. [ 2.037782] cpufreq-nforce2: No nForce2 chipset. [ 2.038264] cpuidle: using governor ladder [ 2.039015] cpuidle: using governor menu [ 2.039019] EFI Variables Facility v0.08 2004-May-17 [ 2.040061] TCP cubic registered [ 2.041438] NET: Registered protocol family 10 [ 2.043814] NET: Registered protocol family 17 [ 2.043823] Registering the dns_resolver key type [ 2.044290] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 2.044336] Using IPI No-Shortcut mode [ 2.045620] PM: Hibernation image not present or could not be loaded. [ 2.045644] registered taskstats version 1 [ 2.073070] Magic number: 4:976:796 [ 2.073415] rtc_cmos 00:07: setting system clock to 2012-07-11 18:45:23 UTC (1342032323) [ 2.076654] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.076658] EDD information not available. [ 2.302111] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.302587] ata1.00: ATA-9: M4-CT128M4SSD2, 000F, max UDMA/100 [ 2.302595] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.303143] ata1.00: configured for UDMA/100 [ 2.303453] scsi 0:0:0:0: Direct-Access ATA M4-CT128M4SSD2 000F PQ: 0 ANSI: 5 [ 2.303746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.303920] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 2.304213] sd 0:0:0:0: [sda] Write Protect is off [ 2.304225] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.304471] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.306818] sda: sda1 sda2 < sda5 > [ 2.308780] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.318162] Refined TSC clocksource calibration: 1595.999 MHz. [ 2.318169] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 2.318178] Switching to clocksource tsc [ 2.450939] hub 1-1:1.0: USB hub found [ 2.451121] hub 1-1:1.0: 6 ports detected [ 2.561786] usb 2-1: new high-speed USB device number 2 using ehci_hcd [ 2.621757] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.636143] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-T633C, D800, max UDMA/100 [ 2.636152] ata2.00: applying bridge limits [ 2.649711] ata2.00: configured for UDMA/100 [ 2.653762] scsi 1:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-T633C D800 PQ: 0 ANSI: 5 [ 2.661486] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.661494] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.661890] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.662156] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.694649] hub 2-1:1.0: USB hub found [ 2.694840] hub 2-1:1.0: 8 ports detected [ 2.765823] usb 1-1.4: new high-speed USB device number 3 using ehci_hcd [ 2.981454] ata6: SATA link down (SStatus 0 SControl 300) [ 2.982597] Freeing unused kernel memory: 740k freed [ 2.983523] Write protecting the kernel text: 5816k [ 2.983808] Write protecting the kernel read-only data: 2376k [ 2.983811] NX-protecting the kernel data: 4424k [ 3.014594] udevd[127]: starting version 175 [ 3.068925] sdhci: Secure Digital Host Controller Interface driver [ 3.068932] sdhci: Copyright(c) Pierre Ossman [ 3.069714] sdhci-pci 0000:09:00.0: SDHCI controller found [1180:e822] (rev 1) [ 3.069742] sdhci-pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.069786] sdhci-pci 0000:09:00.0: Will use DMA mode even though HW doesn't fully claim to support it. [ 3.069798] sdhci-pci 0000:09:00.0: setting latency timer to 64 [ 3.069816] mmc0: no vmmc regulator found [ 3.069877] Registered led device: mmc0:: [ 3.070946] mmc0: SDHCI controller on PCI [0000:09:00.0] using DMA [ 3.071078] tg3.c:v3.121 (November 2, 2011) [ 3.071252] tg3 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.071269] tg3 0000:0b:00.0: setting latency timer to 64 [ 3.071403] firewire_ohci 0000:09:00.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 3.071417] firewire_ohci 0000:09:00.3: setting latency timer to 64 [ 3.078509] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 3.078517] EXT4-fs (sda1): write access will be enabled during recovery [ 3.110417] tg3 0000:0b:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address b8:ac:6f:71:02:a6 [ 3.110425] tg3 0000:0b:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 3.110431] tg3 0000:0b:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.110436] tg3 0000:0b:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 3.125492] firewire_ohci: Added fw-ohci device 0000:09:00.3, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 [ 3.390124] EXT4-fs (sda1): orphan cleanup on readonly fs [ 3.390135] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078710 [ 3.390232] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363071 [ 3.390327] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078711 [ 3.390350] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078709 [ 3.390367] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078708 [ 3.390384] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078707 [ 3.390401] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078706 [ 3.390417] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078705 [ 3.390435] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078551 [ 3.390452] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078523 [ 3.390470] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078520 [ 3.390487] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7077901 [ 3.390551] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063272 [ 3.390562] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063266 [ 3.390572] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063261 [ 3.390582] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063256 [ 3.390592] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063255 [ 3.390602] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363072 [ 3.390620] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2360050 [ 3.390698] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 5250064 [ 3.390710] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365394 [ 3.390728] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365390 [ 3.390745] EXT4-fs (sda1): 22 orphan inodes deleted [ 3.390748] EXT4-fs (sda1): recovery complete [ 3.397636] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 3.624910] firewire_core: created device fw0: GUID 464fc000110e2661, S400 [ 3.927467] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.929965] udevd[400]: starting version 175 [ 3.933581] Adding 6278140k swap on /dev/sda5. Priority:-1 extents:1 across:6278140k SS [ 3.945183] lp: driver loaded but no devices found [ 3.999389] wmi: Mapper loaded [ 4.016696] ite_cir: Auto-detected model: ITE8708 CIR transceiver [ 4.016702] ite_cir: Using model: ITE8708 CIR transceiver [ 4.016706] ite_cir: TX-capable: 1 [ 4.016710] ite_cir: Sample period (ns): 8680 [ 4.016713] ite_cir: TX carrier frequency (Hz): 38000 [ 4.016716] ite_cir: TX duty cycle (%): 33 [ 4.016719] ite_cir: RX low carrier frequency (Hz): 0 [ 4.016722] ite_cir: RX high carrier frequency (Hz): 0 [ 4.025684] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 4.025691] Disabling lock debugging due to kernel taint [ 4.027410] IR NEC protocol handler initialized [ 4.030250] lib80211: common routines for IEEE802.11 drivers [ 4.030257] lib80211_crypt: registered algorithm 'NULL' [ 4.036024] IR RC5(x) protocol handler initialized [ 4.036092] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.036188] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 4.036307] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 4.036361] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 4.039006] acpi device:03: registered as cooling_device10 [ 4.039164] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5 [ 4.039261] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 4.049753] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 4.050201] wl 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.050215] wl 0000:05:00.0: setting latency timer to 64 [ 4.052252] Registered IR keymap rc-rc6-mce [ 4.052432] input: ITE8708 CIR transceiver as /devices/virtual/rc/rc0/input6 [ 4.054614] IR RC6 protocol handler initialized [ 4.054787] rc0: ITE8708 CIR transceiver as /devices/virtual/rc/rc0 [ 4.054839] ite_cir: driver has been successfully loaded [ 4.057338] IR JVC protocol handler initialized [ 4.061553] IR Sony protocol handler initialized [ 4.066578] input: MCE IR Keyboard/Mouse (ite-cir) as /devices/virtual/input/input7 [ 4.066724] IR MCE Keyboard/mouse protocol handler initialized [ 4.072580] lirc_dev: IR Remote Control driver registered, major 250 [ 4.073280] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0 [ 4.073286] IR LIRC bridge handler initialized [ 4.077849] Linux video capture interface: v2.00 [ 4.079402] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:640f) [ 4.085492] EDAC MC: Ver: 2.1.0 [ 4.087138] lib80211_crypt: registered algorithm 'TKIP' [ 4.091027] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 4.091733] snd_hda_intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.091826] snd_hda_intel 0000:02:00.1: irq 47 for MSI/MSI-X [ 4.091861] snd_hda_intel 0000:02:00.1: setting latency timer to 64 [ 4.093115] EDAC i7core: Device not found: dev 00.0 PCI ID 8086:2c50 [ 4.112448] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 4.112612] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input9 [ 4.113311] type=1400 audit(1342032325.540:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=658 comm="apparmor_parser" [ 4.114501] type=1400 audit(1342032325.540:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=658 comm="apparmor_parser" [ 4.115253] type=1400 audit(1342032325.540:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=658 comm="apparmor_parser" [ 4.121870] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10 [ 4.122096] usbcore: registered new interface driver uvcvideo [ 4.122100] USB Video Class driver (1.1.1) [ 4.128729] [fglrx] Maximum main memory to use for locked dma buffers: 5840 MBytes. [ 4.129678] [fglrx] vendor: 1002 device: 68c0 count: 1 [ 4.131991] [fglrx] ioport: bar 4, base 0x2000, size: 0x100 [ 4.132015] pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.132024] pci 0000:02:00.0: setting latency timer to 64 [ 4.133712] [fglrx] Kernel PAT support is enabled [ 4.133747] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 4.162666] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.100.82.38 [ 4.184133] device-mapper: multipath: version 1.3.0 loaded [ 4.196660] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 4.279897] input: Dell WMI hotkeys as /devices/virtual/input/input11 [ 4.292402] Bluetooth: Core ver 2.16 [ 4.292449] NET: Registered protocol family 31 [ 4.292454] Bluetooth: HCI device and connection manager initialized [ 4.292459] Bluetooth: HCI socket layer initialized [ 4.292463] Bluetooth: L2CAP socket layer initialized [ 4.292473] Bluetooth: SCO socket layer initialized [ 4.296333] Bluetooth: RFCOMM TTY layer initialized [ 4.296342] Bluetooth: RFCOMM socket layer initialized [ 4.296345] Bluetooth: RFCOMM ver 1.11 [ 4.313586] ppdev: user-space parallel port driver [ 4.316619] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.316625] Bluetooth: BNEP filters: protocol multicast [ 4.383980] type=1400 audit(1342032325.812:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=938 comm="apparmor_parser" [ 4.385173] type=1400 audit(1342032325.812:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=938 comm="apparmor_parser" [ 4.425757] init: failsafe main process (898) killed by TERM signal [ 4.477052] type=1400 audit(1342032325.904:7): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1011 comm="apparmor_parser" [ 4.477592] type=1400 audit(1342032325.904:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 4.478099] type=1400 audit(1342032325.904:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1017 comm="apparmor_parser" [ 4.479233] type=1400 audit(1342032325.904:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 4.510060] vesafb: mode is 1152x864x32, linelength=4608, pages=0 [ 4.510065] vesafb: scrolling: redraw [ 4.510071] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 4.510084] mtrr: no more MTRRs available [ 4.513081] vesafb: framebuffer at 0xd0000000, mapped to 0xf9400000, using 3904k, total 3904k [ 4.515203] Console: switching to colour frame buffer device 144x54 [ 4.515278] fb0: VESA VGA frame buffer device [ 4.590743] tg3 0000:0b:00.0: irq 48 for MSI/MSI-X [ 4.702009] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.704409] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.978379] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 5.030104] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12 [ 5.045782] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 5.519573] [fglrx] ATIF platform detected with notification ID: 0x81 [ 6.391466] fglrx_pci 0000:02:00.0: irq 49 for MSI/MSI-X [ 6.393137] [fglrx] Firegl kernel thread PID: 1305 [ 6.393306] [fglrx] Firegl kernel thread PID: 1306 [ 6.393472] [fglrx] Firegl kernel thread PID: 1307 [ 6.393726] [fglrx] IRQ 49 Enabled [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. [ 6.532080] [fglrx] Gart USWC size:1280 M. [ 6.532084] [fglrx] Gart cacheable size:508 M. [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 [ 17.423743] eth1: no IPv6 routers present [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 [ 543.679614] eth1: no IPv6 routers present lsmod Module Size Used by kvm_intel 127560 0 kvm 359456 1 kvm_intel joydev 17393 0 vesafb 13516 1 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 rfcomm 38139 0 bluetooth 158438 10 bnep,rfcomm dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi binfmt_misc 17292 1 dell_laptop 17767 0 dcdbas 14098 1 dell_laptop dm_multipath 22710 0 fglrx 2909855 143 snd_hda_codec_hdmi 31775 1 psmouse 72919 0 serio_raw 13027 0 i7core_edac 23382 0 lib80211_crypt_tkip 17275 0 edac_core 46858 1 i7core_edac uvcvideo 67203 0 snd_hda_codec_idt 60251 1 videodev 86588 1 uvcvideo ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec ir_mce_kbd_decoder 12681 0 snd_seq_midi 13132 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 snd_rawmidi 25424 1 snd_seq_midi ir_rc6_decoder 12459 0 wl 2646601 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event ir_rc5_decoder 12459 0 video 19068 0 snd_hda_intel 32765 5 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel rc_rc6_mce 12454 0 lib80211 14040 2 lib80211_crypt_tkip,wl snd_hwdep 13276 1 snd_hda_codec ir_nec_decoder 12459 0 snd_pcm 80845 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec ite_cir 24743 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ite_cir snd_timer 28931 2 snd_seq,snd_pcm wmi 18744 1 dell_wmi snd 62064 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_rawmidi,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer mac_hid 13077 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm coretemp 13269 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141369 0 firewire_ohci 40172 0 sdhci_pci 18324 0 firewire_core 56906 1 firewire_ohci sdhci 28241 1 sdhci_pci crc_itu_t 12627 1 firewire_core lshw *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:a9:54:31 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.0.117 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0900000-f0903fff *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 logical name: eth0 version: 10 serial: b8:ac:6f:71:02:a6 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:48 memory:f0d00000-f0d0ffff

  Read the article

• SOLVED Install MythTV & 11.10 on Lenovo S12 (Intel atom) with wireless

  - by keepitsimpleengineer

  This is how I installed Ubuntu 11.10 and MythTV client on my Lenovo S12 (Intel Atom) laptop and use it using WiFi (see additional notes at end). I did this because the upgrade from 11.04 bricked the laptop. Note that the partitions on the Lenovo standard disk were already in place for this installation. Also note that my LAN is setup for fixed IP addresses. Downloaded and burned 11.10 x86 Desktop Ubuntu CD Connected the power supply cord, LAN wire and the external DVD USB drive. Ran Windows XP and made sure performance level "Performance" was set and "Wireless" was enabled. Booted S12 from CD Disabled Networking from icon on upper left panel icon Edited Connections… "Wired connection 1" ? Set IP address, accepted default netmask and set gateway. Also set DNS server. Good idea to check "Connection Information" here to verify everything's O.K. Selected Install Ubuntu from the initial "Install" window Verified the three items were checked (required disk space available, plugged into a power source, & connected to the Internet) Selected Download updates while installing and third party software. Hit Continue… At wireless selected don't want to connect…WiFi…now. Continue… At Installation type, selected Something else. Continue… At partition tale, selected the ext4 Linux partition, set the mount point as "/", and marked for formatting. Here I selected the main disk (/sda) for installing the boot manager. Continue… Selected or verified my Time zone. Continue… Selected my keyboard layout. Continue… Filled in the who are you fields. Make sure password is required to sign in is checked. Continue… Chose a picture. Continue… I selected import no accounts. Continue… Wait as the Install creeps along. If your screen goes blank, tap the space bar ? apparently the screen saver/power plan does this. There are several progress bars. The longest was "Installing system", and it was the next to the last one. Installation Complete window appears, Restart Now… Wait as it stops, The screen blanks then the message "…remove…media…close tray…press enter" I just unplugged the USB DVD and hit enter… It was disheartening but the screen turned Ubuntu Purple-beige and nothing happened, so I help down the power key until it shut down, the pressed it again and the Grub Boot screen appeared. Select Ubuntu… 25.The screen went blank with the little flashing underscore cursor on it and the disk light would occasionally flash. I hit the enter key and eventuality Ubuntu started. After a somewhat long time the unity desktop appeared. 11.10, unlike earlier versions, retains the connection information. Check this by checking the network icon on the upper left applet panel. Here the touch-pad·mouse quit working and I had to reboot. It takes and extremely long time to boot, sometimes requiring several power off/ power on (cold boot). You can try to get the default network manager to work, but it might not, it didn't on mine for WiFi. Thanks to: Chris at URL here's what to do… disconnect your wired Internet connection. input your wireless information into network manager open a terminal (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "terminal". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. click to open a terminal, and type in: sudo rmmod acer_wmi && echo "blacklist acer_wmi" >> /etc/modprobe.d/blacklist.conf and hit enter. type in your password as asked. if you have correctly entered your WiFi information and you are near your AP, you should connect immediately if not, see the URL above ? you might need to replace "network manager" with "wicd" ? I did with 11.04. Update the new 11.10, in the upper left panel applet weird·gear icon is menu with a line about updating. It's the new way to invoke Update Manager. Your lenovo S12 (intel atom) should now run the new unity Ubuntu. Point your elbow at the ceiling and pat yourself on the back. Installing Mythbuntu Client 24.1 Open mythbuntu.org/repos (I urge you not to directly use Ubuntu Software Center for this) Install Mythbuntu Repos Save the file (in ~/Downloads, the default) Run the file ? it will update your repositories so that you will get the proper installation sources ? it will start Ubuntu Software Center to do this ? Click Install… You will need your password. Debconf window will open, select by making sure check mark is in the little box "Would you like to activate…". Forward… Which version? At the time of writing the current "Stable" version was 24.1, select 0.24.x… Forward… Read the message, then forward… Delete the downloaded file. Install synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "synaptic". Click on the synaptic icon. Ubuntu Software Center will open and allow you to install synaptic package manager. Open Synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "Synaptic". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. Run synaptic, read the intro, and close the intro window. Type in mythbuntu-control-centre in the Quick filter text box, and then select it "Mark for installation" by clicking on the box next to it's name. Marvel at the additional to be installed items, then select "?Mark"… At the top of the synaptic window click on the "? Apply" button. Marvel at the amount of stuff to be installed, the click on "Apply". When finished, close finished window and synaptic. Open mythbuntu-control-centre (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythbuntu". Might be a good idea to drag and drop the mythbuntu-control-centre icon to the terminal, it's easy to get rid of later. You can now configure and install the frontend. Go down the icon totem on the right side of the window and click as needed… System roles. ? No Backend, Desktop Frontend, and Ubuntu Desktop. Apply… & Apply changes… & Password… MySQL Configuration ? from backend ? Setup General Alt-N(ext) Alt-N(ext) Stetting Access Setup PIN code: ~~~~ Input Security key and click "Test Connection", if ?, then Apply… & Apply… {note: for some inexplicable reason, control centre hung on this, but when I restarted it, it was set properly} Graphics drivers, When I did this, only the Broadcom wireless driver showed up. I closed without doing anything. Services. I enabled SSH & Samba. Apply… & Apply… Repositories. Asked & Answered. MythExport. Pass, I believe it requires backend on the same system. Proprietary Codec Support. Check to enable, Apply… & Apply… System Updates. No action necessary, will be a part of the Ubuntu update mechanism. Themes and Artwork. For themes, I selected Enable/Update all. Apply… & Apply… Infrared & Startup behavior and Plugins. Defer until you know more. Close software centre. Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Incorrect Group Membership. Fix this by clicking "Yes"… Log out/end. Do this by clicking "Yes"… For my Lenovo S12, I had to manually restart Ubuntu - and still with the very long restart…/no start/cold boot/reboot/pressing the shift key required Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Will open with Select country & language. Do so. then get message with "No", hit "Ok" and arrive at the data base Configuration 1/2 screen. You will need your brackend password, from backend ? Setup General Database Configuration 1/2 Password:~? Enter this Hit Alt-n to go to the next page. Select "Use custom id…", then enter a custom ID, I use the machine's name. Hit finish, and MythTV should start up with all default settings. For the lenovo S12, the first thing you want to do is to set Playback profiles to "Normal". From Setup TV Settings Playback Alt-N(ext) Alt-N(ext) Playback Profiles (3/8) : Change Current Video Playback Profile to "Normal". You can fiddle with this setting later. For the lenovo S12, the second thing is to get the sound going. From Setup General Alt-N(ext) Alt-N(ext) Alt-N(ext) Audio System: The top of the screen is a button title "Scan for audio devices", move the highlight there and press the Space bar. Then Tab down to Audio Output Device: and left-right arrow until "ALSA:hw:Card=Intel,DEV=0" is selected. Then Alt-N(ext) until "Finish". Now you should have sound. You should now have MythTV working nicely on the Lenovo S12 Notes about wireless: Running Lenovo S12 on wireless is demanding on both power and WiFi connection. Best results will be obtained when running on power and wired connection. I run my S12 on wireless, actually two serial connections with two access points, something that is not easy to achieve. Here Mythbuntu client-server (in den) <? wireless link 1 <?office LAN? wireless link 2 <? Lenovo S12 Ubuntu 11.10 The office LAN is fixed IP behind an Untangle firewall router. There is another MythTV client on Ubuntu 10.10 computer in the office (which has always worked well). ProblemMythbuntu\Win7 client hangs with frozen frames, short segment of audio repeating. Hardware Rosewill RNX-G300EX IEEE 802.11b/g PCI Wireless Card on client-server 2 Linksys WRT54GL wireless broadband routers on LAN for link1 and link 2 WRT54GL FirmwareDD-WRT v24-sp2(07/22/09) voip set up to act as an access point. Note? many people advised this was an unworkable scheme, and in probably most cases it will be. Solution? Set up DD-WRT with the following Wireless settings… Basic Channel: Different fixed channels at least 4 difference, I use 6 & 11 Basic Sensitivity Range (ACK timing): 50 MAC filter use filter: Enable, Selected Permit only clients listed to access… Requires adding MAC addresses in "Edit MAC Filter List" This causes the 54GL's to ignore any but the listed MAC address, down side, no "guest" capability. Advanced Basic rate: All Advanced CTS Protection Mode: Off Advanced Frame Burst: Enable Advanced Max associate clients: 4 for client link 2, 1 for client-server link 1 Advanced AP isolation: Enable Advanced Preamble: Short Advanced Afterburner: On Advanced Wireless GUI access: Off Advanced WMM support: Off Other settings: default for supplied firmware. Why I suspect this worked? The 54GL Access Points's with the firmware's setting are set to handle a multiple client, wide area situation. With these mods I reconfigured them for a small area, few client situation, disabling Advanced WMM probably the most important. In addition, the client mythtv when used all other users of its access point are turned off except for a Skype phone. Also, the client-server is set up to allow other connections though it's LAN connection, and these are used to connect the TV and disc players, not used when client is being used.

  Read the article

• Creating ActionEvent object for CustomButton in Java

  - by Crystal

  For a hw assignment, we were supposed to create a custom button to get familiar with swing and responding to events. We were also to make this button an event source which confuses me. I have an ArrayList to keep track of listeners that would register to listen to my CustomButton. What I am getting confused on is how to notify the listeners. My teacher hinted at having a notify and overriding actionPerformed which I tried doing, but then I wasn't sure how to create an ActionEvent object looking at the constructor documentation. The source, id, string all confuses me. Any help would be appreciated. Thanks! code: import java.awt.*; import java.awt.event.*; import javax.swing.*; import java.util.List; import java.util.ArrayList; public class CustomButton { public static void main(String[] args) { EventQueue.invokeLater(new Runnable() { public void run() { CustomButtonFrame frame = new CustomButtonFrame(); frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); frame.setVisible(true); } }); } public void addActionListener(ActionListener al) { listenerList.add(al); } public void removeActionListener(ActionListener al) { listenerList.remove(al); } public void actionPerformed(ActionEvent e) { System.out.println("Button Clicked!"); } private void notifyListeners() { ActionEvent event = new ActionEvent(CONFUSED HERE!!!!; for (ActionListener action : listenerList) { action.actionPerfomed(event); } } List<ActionListener> listenerList = new ArrayList<ActionListener>(); } class CustomButtonFrame extends JFrame { // constructor for CustomButtonFrame public CustomButtonFrame() { setTitle("Custom Button"); CustomButtonSetup buttonSetup = new CustomButtonSetup(); this.add(buttonSetup); this.pack(); } } class CustomButtonSetup extends JComponent { public CustomButtonSetup() { ButtonAction buttonClicked = new ButtonAction(); this.addMouseListener(buttonClicked); } // because frame includes borders and insets, use this method public Dimension getPreferredSize() { return new Dimension(200, 200); } public void paintComponent(Graphics g) { Graphics2D g2 = (Graphics2D) g; // first triangle coords int x[] = new int[TRIANGLE_SIDES]; int y[] = new int[TRIANGLE_SIDES]; x[0] = 0; y[0] = 0; x[1] = 200; y[1] = 0; x[2] = 0; y[2] = 200; Polygon firstTriangle = new Polygon(x, y, TRIANGLE_SIDES); // second triangle coords x[0] = 0; y[0] = 200; x[1] = 200; y[1] = 200; x[2] = 200; y[2] = 0; Polygon secondTriangle = new Polygon(x, y, TRIANGLE_SIDES); g2.drawPolygon(firstTriangle); g2.setColor(firstColor); g2.fillPolygon(firstTriangle); g2.drawPolygon(secondTriangle); g2.setColor(secondColor); g2.fillPolygon(secondTriangle); // draw rectangle 10 pixels off border int s1[] = new int[RECT_SIDES]; int s2[] = new int[RECT_SIDES]; s1[0] = 5; s2[0] = 5; s1[1] = 195; s2[1] = 5; s1[2] = 195; s2[2] = 195; s1[3] = 5; s2[3] = 195; Polygon rectangle = new Polygon(s1, s2, RECT_SIDES); g2.drawPolygon(rectangle); g2.setColor(thirdColor); g2.fillPolygon(rectangle); } private class ButtonAction implements MouseListener { public void mousePressed(MouseEvent e) { System.out.println("Click!"); firstColor = Color.GRAY; secondColor = Color.WHITE; repaint(); } public void mouseReleased(MouseEvent e) { System.out.println("Released!"); firstColor = Color.WHITE; secondColor = Color.GRAY; repaint(); } public void mouseEntered(MouseEvent e) {} public void mouseExited(MouseEvent e) {} public void mouseClicked(MouseEvent e) {} } public static final int TRIANGLE_SIDES = 3; public static final int RECT_SIDES = 4; private Color firstColor = Color.WHITE; private Color secondColor = Color.DARK_GRAY; private Color thirdColor = Color.LIGHT_GRAY; }

  Read the article

• ubuntu 10.04 logs itself out overnight

  - by Corey

  Every night when I leave work, I lock the screen via ubuntu's "power" button in the top right hand panel. When I come to work in the morning, I'm greeted with the log-in screen. This doesn't happen every night, but most. I'm running ubuntu 10.04 on a Dell inspiron. I've included some HW specs, and also dmesg output. Please let me know what other logs may be useful. thanks! Corey ~$ dmesg [20559.696062] type=1503 audit(1285957687.048:16): operation="open" pid=6212 parent=1 profile="/usr/bin/evince" requested_mask="::r" denied_mask="::r" fsuid=1000 ouid=0 name="/usr/local/lib/libltdl.so.7.2.2" [21127.951621] type=1503 audit(1285958255.300:17): operation="open" pid=6390 parent=1 profile="/usr/bin/evince" requested_mask="::r" denied_mask="::r" fsuid=1000 ouid=0 name="/usr/local/lib/libltdl.so.7.2.2" [291038.528014] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [291038.528025] render error detected, EIR: 0x00000000 [291038.528042] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 22973891 at 22973890) [291038.828014] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [291038.828023] render error detected, EIR: 0x00000000 [291038.828042] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 22973894 at 22973890) ~$ lspci -vv 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 27 Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at dc00 [size=8] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at feaf8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: 80000000-801fffff Prefetchable memory behind bridge: 0000000080200000-00000000803fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: feb00000-febfffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at d880 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at d800 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at d480 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d400 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) (prog-if 20) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at feaf7c00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt, intel-rng 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at d080 [size=8] Region 1: I/O ports at d000 [size=4] Region 2: I/O ports at cc00 [size=8] Region 3: I/O ports at c880 [size=4] Region 4: I/O ports at c800 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 4: I/O ports at 0400 [size=32] Kernel modules: i2c-i801 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: I/O ports at e800 [size=256] Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fdfe0000 (64-bit, prefetchable) [size=64K] Expansion ROM at febe0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 log$ tail -n 15 Xorg.0.log.old for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. (II) Power Button: Close (II) UnloadModule: "evdev" (II) Power Button: Close (II) UnloadModule: "evdev" (II) USB Optical Mouse: Close (II) UnloadModule: "evdev" (II) Dell Dell USB Entry Keyboard: Close (II) UnloadModule: "evdev" (II) Macintosh mouse button emulation: Close (II) UnloadModule: "evdev" (II) AIGLX: Suspending AIGLX clients for VT switch ddxSigGiveUp: Closing log

  Read the article

• Windows periodically disconnects, reconnects to the network

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

  Read the article

• Another "Windows 7 entry missing from Grub2" Question

  - by 4x10

  Like many before me had the following problem that after installing Ubuntu (with windows 7 already installed), the grub boot loader wouldnt show windows 7 as a boot option, though i can boot fine if I use the "Choose Boot Device" options on the x220. The difference is that I try using UEFI only so many answers didn't really fit my problem, though i tried several stuffs: after running boot repair it destroyed the ubuntu boot loader custom entry in /etc/grub.d/40_custom for windows which doesnt show up many update-grub and reboots trying windows repair recovery thing while being there i also did bootrec.exe /FixBoot and update-grub and reboot again and finaly because it was so much fun, i installed linux all over again, while formatting and deleting everything linux related before that. Now that i think of it, Ubuntu also didn't notice Windows being there during the Setup and it still doesnt according to the Boot Info from Boot Repair. Boot Info Script 0.61-git-patched [23 April 2012] ============================= Boot Info Summary: =============================== => No boot loader is installed in the MBR of /dev/sda. sda1: __________________________________________________________________________ File system: vfat Boot sector type: Windows 7: FAT32 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /efi/Boot/bootx64.efi /efi/ubuntu/grubx64.efi sda2: __________________________________________________________________________ File system: Boot sector type: - Boot sector info: Mounting failed: mount: unknown filesystem type '' sda3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /Windows/System32/winload.exe sda4: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu precise (development branch) Boot files: /boot/grub/grub.cfg /etc/fstab sda5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sda6: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 1 625,142,447 625,142,447 ee GPT GUID Partition Table detected. Partition Start Sector End Sector # of Sectors System /dev/sda1 2,048 206,847 204,800 EFI System partition /dev/sda2 206,848 468,991 262,144 Microsoft Reserved Partition (Windows) /dev/sda3 468,992 170,338,303 169,869,312 Data partition (Windows/Linux) /dev/sda4 170,338,304 330,338,304 160,000,001 Data partition (Windows/Linux) /dev/sda5 330,338,305 617,141,039 286,802,735 Data partition (Windows/Linux) /dev/sda6 617,141,040 625,141,040 8,000,001 Swap partition (Linux) "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 885C-ED1B vfat /dev/sda3 EE06CC0506CBCCB1 ntfs /dev/sda4 604dd3b2-64ca-4200-b8fb-820e8d0ca899 ext4 /dev/sda5 d62515fd-8120-4a74-b17b-0bdf244124a3 ext4 /dev/sda6 7078b649-fb2a-4c59-bd03-fd31ef440d37 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda1 /boot/efi vfat (rw) /dev/sda4 / ext4 (rw,errors=remount-ro) /dev/sda5 /home ext4 (rw) =========================== sda4/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod efi_gop insmod efi_uga insmod video_bochs insmod video_cirrus } insmod part_gpt insmod ext2 set root='(hd0,gpt4)' search --no-floppy --fs-uuid --set=root 604dd3b2-64ca-4200-b8fb-820e8d0ca899 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_gpt insmod ext2 set root='(hd0,gpt4)' search --no-floppy --fs-uuid --set=root 604dd3b2-64ca-4200-b8fb-820e8d0ca899 set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="$1" if [ "$1" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-20-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='(hd0,gpt4)' search --no-floppy --fs-uuid --set=root 604dd3b2-64ca-4200-b8fb-820e8d0ca899 linux /boot/vmlinuz-3.2.0-20-generic root=UUID=604dd3b2-64ca-4200-b8fb-820e8d0ca899 ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-20-generic } menuentry 'Ubuntu, with Linux 3.2.0-20-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_gpt insmod ext2 set root='(hd0,gpt4)' search --no-floppy --fs-uuid --set=root 604dd3b2-64ca-4200-b8fb-820e8d0ca899 echo 'Loading Linux 3.2.0-20-generic ...' linux /boot/vmlinuz-3.2.0-20-generic root=UUID=604dd3b2-64ca-4200-b8fb-820e8d0ca899 ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-20-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_gpt insmod ext2 set root='(hd0,gpt4)' search --no-floppy --fs-uuid --set=root 604dd3b2-64ca-4200-b8fb-820e8d0ca899 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_gpt insmod ext2 set root='(hd0,gpt4)' search --no-floppy --fs-uuid --set=root 604dd3b2-64ca-4200-b8fb-820e8d0ca899 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda4/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda4 during installation UUID=604dd3b2-64ca-4200-b8fb-820e8d0ca899 / ext4 errors=remount-ro 0 1 # /boot/efi was on /dev/sda1 during installation UUID=885C-ED1B /boot/efi vfat defaults 0 1 # /home was on /dev/sda5 during installation UUID=d62515fd-8120-4a74-b17b-0bdf244124a3 /home ext4 defaults 0 2 # swap was on /dev/sda6 during installation UUID=7078b649-fb2a-4c59-bd03-fd31ef440d37 none swap sw 0 0 -------------------------------------------------------------------------------- =================== sda4: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 129.422874451 = 138.966753280 boot/grub/grub.cfg 1 83.059570312 = 89.184534528 boot/initrd.img-3.2.0-20-generic 2 101.393131256 = 108.870045696 boot/vmlinuz-3.2.0-20-generic 1 83.059570312 = 89.184534528 initrd.img 2 101.393131256 = 108.870045696 vmlinuz 1 ADDITIONAL INFORMATION : =================== log of boot-repair 2012-04-25__23h40 =================== boot-repair version : 3.18-0ppa3~precise boot-sav version : 3.18-0ppa4~precise glade2script version : 0.3.2.1-0ppa7~precise internet: connected python-software-properties version : 0.82.7 0 upgraded, 0 newly installed, 1 reinstalled, 0 to remove and 591 not upgraded. dpkg-preconfigure: unable to re-open stdin: No such file or directory boot-repair is executed in installed-session (Ubuntu precise (development branch) , precise , Ubuntu , x86_64) WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. =================== OSPROBER: /dev/sda4:The OS now in use - Ubuntu precise (development branch) CurrentSession:linux =================== BLKID: /dev/sda3: UUID="EE06CC0506CBCCB1" TYPE="ntfs" /dev/sda1: UUID="885C-ED1B" TYPE="vfat" /dev/sda4: UUID="604dd3b2-64ca-4200-b8fb-820e8d0ca899" TYPE="ext4" /dev/sda5: UUID="d62515fd-8120-4a74-b17b-0bdf244124a3" TYPE="ext4" /dev/sda6: UUID="7078b649-fb2a-4c59-bd03-fd31ef440d37" TYPE="swap" 1 disks with OS, 1 OS : 1 Linux, 0 MacOS, 0 Windows, 0 unknown type OS. WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util sfdisk doesn't support GPT. Use GNU Parted. =================== /etc/default/grub : # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" EFI_OF_PART[1] (, ) =================== dmesg | grep EFI : [ 0.000000] EFI v2.00 by Lenovo [ 0.000000] Kernel-defined memdesc doesn't match the one from EFI! [ 0.000000] EFI: mem00: type=3, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB) [ 0.000000] EFI: mem01: type=7, attr=0xf, range=[0x0000000000001000-0x000000000004e000) (0MB) [ 0.000000] EFI: mem02: type=3, attr=0xf, range=[0x000000000004e000-0x0000000000058000) (0MB) [ 0.000000] EFI: mem03: type=10, attr=0xf, range=[0x0000000000058000-0x0000000000059000) (0MB) [ 0.000000] EFI: mem04: type=7, attr=0xf, range=[0x0000000000059000-0x000000000005e000) (0MB) [ 0.000000] EFI: mem05: type=4, attr=0xf, range=[0x000000000005e000-0x000000000005f000) (0MB) [ 0.000000] EFI: mem06: type=3, attr=0xf, range=[0x000000000005f000-0x00000000000a0000) (0MB) [ 0.000000] EFI: mem07: type=2, attr=0xf, range=[0x0000000000100000-0x00000000005b9000) (4MB) [ 0.000000] EFI: mem08: type=7, attr=0xf, range=[0x00000000005b9000-0x0000000020000000) (506MB) [ 0.000000] EFI: mem09: type=0, attr=0xf, range=[0x0000000020000000-0x0000000020200000) (2MB) [ 0.000000] EFI: mem10: type=7, attr=0xf, range=[0x0000000020200000-0x00000000364e4000) (354MB) [ 0.000000] EFI: mem11: type=2, attr=0xf, range=[0x00000000364e4000-0x000000003726a000) (13MB) [ 0.000000] EFI: mem12: type=7, attr=0xf, range=[0x000000003726a000-0x0000000040000000) (141MB) [ 0.000000] EFI: mem13: type=0, attr=0xf, range=[0x0000000040000000-0x0000000040200000) (2MB) [ 0.000000] EFI: mem14: type=7, attr=0xf, range=[0x0000000040200000-0x000000009df35000) (1501MB) [ 0.000000] EFI: mem15: type=2, attr=0xf, range=[0x000000009df35000-0x00000000d39a0000) (858MB) [ 0.000000] EFI: mem16: type=4, attr=0xf, range=[0x00000000d39a0000-0x00000000d39c0000) (0MB) [ 0.000000] EFI: mem17: type=7, attr=0xf, range=[0x00000000d39c0000-0x00000000d5df5000) (36MB) [ 0.000000] EFI: mem18: type=4, attr=0xf, range=[0x00000000d5df5000-0x00000000d6990000) (11MB) [ 0.000000] EFI: mem19: type=7, attr=0xf, range=[0x00000000d6990000-0x00000000d6b82000) (1MB) [ 0.000000] EFI: mem20: type=1, attr=0xf, range=[0x00000000d6b82000-0x00000000d6b9f000) (0MB) [ 0.000000] EFI: mem21: type=7, attr=0xf, range=[0x00000000d6b9f000-0x00000000d77b0000) (12MB) [ 0.000000] EFI: mem22: type=4, attr=0xf, range=[0x00000000d77b0000-0x00000000d780a000) (0MB) [ 0.000000] EFI: mem23: type=7, attr=0xf, range=[0x00000000d780a000-0x00000000d7826000) (0MB) [ 0.000000] EFI: mem24: type=4, attr=0xf, range=[0x00000000d7826000-0x00000000d7868000) (0MB) [ 0.000000] EFI: mem25: type=7, attr=0xf, range=[0x00000000d7868000-0x00000000d7869000) (0MB) [ 0.000000] EFI: mem26: type=4, attr=0xf, range=[0x00000000d7869000-0x00000000d786a000) (0MB) [ 0.000000] EFI: mem27: type=7, attr=0xf, range=[0x00000000d786a000-0x00000000d786b000) (0MB) [ 0.000000] EFI: mem28: type=4, attr=0xf, range=[0x00000000d786b000-0x00000000d786c000) (0MB) [ 0.000000] EFI: mem29: type=7, attr=0xf, range=[0x00000000d786c000-0x00000000d786d000) (0MB) [ 0.000000] EFI: mem30: type=4, attr=0xf, range=[0x00000000d786d000-0x00000000d825f000) (9MB) [ 0.000000] EFI: mem31: type=7, attr=0xf, range=[0x00000000d825f000-0x00000000d8261000) (0MB) [ 0.000000] EFI: mem32: type=4, attr=0xf, range=[0x00000000d8261000-0x00000000d82f7000) (0MB) [ 0.000000] EFI: mem33: type=7, attr=0xf, range=[0x00000000d82f7000-0x00000000d82f8000) (0MB) [ 0.000000] EFI: mem34: type=4, attr=0xf, range=[0x00000000d82f8000-0x00000000d8705000) (4MB) [ 0.000000] EFI: mem35: type=7, attr=0xf, range=[0x00000000d8705000-0x00000000d8706000) (0MB) [ 0.000000] EFI: mem36: type=4, attr=0xf, range=[0x00000000d8706000-0x00000000d8761000) (0MB) [ 0.000000] EFI: mem37: type=7, attr=0xf, range=[0x00000000d8761000-0x00000000d8768000) (0MB) [ 0.000000] EFI: mem38: type=4, attr=0xf, range=[0x00000000d8768000-0x00000000d9b9f000) (20MB) [ 0.000000] EFI: mem39: type=7, attr=0xf, range=[0x00000000d9b9f000-0x00000000d9e4c000) (2MB) [ 0.000000] EFI: mem40: type=2, attr=0xf, range=[0x00000000d9e4c000-0x00000000d9e52000) (0MB) [ 0.000000] EFI: mem41: type=3, attr=0xf, range=[0x00000000d9e52000-0x00000000da59f000) (7MB) [ 0.000000] EFI: mem42: type=5, attr=0x800000000000000f, range=[0x00000000da59f000-0x00000000da6c3000) (1MB) [ 0.000000] EFI: mem43: type=5, attr=0x800000000000000f, range=[0x00000000da6c3000-0x00000000da79f000) (0MB) [ 0.000000] EFI: mem44: type=6, attr=0x800000000000000f, range=[0x00000000da79f000-0x00000000da8b1000) (1MB) [ 0.000000] EFI: mem45: type=6, attr=0x800000000000000f, range=[0x00000000da8b1000-0x00000000da99f000) (0MB) [ 0.000000] EFI: mem46: type=0, attr=0xf, range=[0x00000000da99f000-0x00000000daa22000) (0MB) [ 0.000000] EFI: mem47: type=0, attr=0xf, range=[0x00000000daa22000-0x00000000daa9b000) (0MB) [ 0.000000] EFI: mem48: type=0, attr=0xf, range=[0x00000000daa9b000-0x00000000daa9c000) (0MB) [ 0.000000] EFI: mem49: type=0, attr=0xf, range=[0x00000000daa9c000-0x00000000daa9f000) (0MB) [ 0.000000] EFI: mem50: type=10, attr=0xf, range=[0x00000000daa9f000-0x00000000daadd000) (0MB) [ 0.000000] EFI: mem51: type=10, attr=0xf, range=[0x00000000daadd000-0x00000000dab9f000) (0MB) [ 0.000000] EFI: mem52: type=9, attr=0xf, range=[0x00000000dab9f000-0x00000000dabdc000) (0MB) [ 0.000000] EFI: mem53: type=9, attr=0xf, range=[0x00000000dabdc000-0x00000000dabff000) (0MB) [ 0.000000] EFI: mem54: type=4, attr=0xf, range=[0x00000000dabff000-0x00000000dac00000) (0MB) [ 0.000000] EFI: mem55: type=7, attr=0xf, range=[0x0000000100000000-0x000000021e600000) (4582MB) [ 0.000000] EFI: mem56: type=11, attr=0x8000000000000001, range=[0x00000000f80f8000-0x00000000f80f9000) (0MB) [ 0.000000] EFI: mem57: type=11, attr=0x8000000000000001, range=[0x00000000fed1c000-0x00000000fed20000) (0MB) [ 0.000000] ACPI: UEFI 00000000dabde000 0003E (v01 LENOVO TP-8D 00001280 PTL 00000002) [ 0.000000] ACPI: UEFI 00000000dabdd000 00042 (v01 PTL COMBUF 00000001 PTL 00000001) [ 0.000000] ACPI: UEFI 00000000dabdc000 00292 (v01 LENOVO TP-8D 00001280 PTL 00000002) [ 0.795807] fb0: EFI VGA frame buffer device [ 1.057243] EFI Variables Facility v0.08 2004-May-17 [ 9.122104] fb: conflicting fb hw usage inteldrmfb vs EFI VGA - removing generic driver ReadEFI: /dev/sda , N 128 , 0 , , PRStart 1024 , PRSize 128 WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. =================== PARTITIONS & DISKS: sda4 : sda, not-sepboot, grubenv-ok grub2, grub-efi, update-grub, 64, with-boot, is-os, gpt-but-not-EFI, fstab-has-bad-efi, no-nt, no-winload, no-recov-nor-hid, no-bmgr, no-grldr, no-b-bcd, apt-get, grub-install, . sda3 : sda, maybesepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, gpt-but-not-EFI, part-has-no-fstab, no-nt, haswinload, no-recov-nor-hid, no-bmgr, no-grldr, no-b-bcd, nopakmgr, nogrubinstall, /mnt/boot-sav/sda3. sda1 : sda, maybesepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, is-correct-EFI, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, no-grldr, no-b-bcd, nopakmgr, nogrubinstall, /boot/efi. sda5 : sda, maybesepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, gpt-but-not-EFI, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, no-grldr, no-b-bcd, nopakmgr, nogrubinstall, /home. sda : GPT-BIS, GPT, no-BIOS_boot, has-correctEFI, 2048 sectors * 512 bytes =================== PARTED: Model: ATA HITACHI HTS72323 (scsi) Disk /dev/sda: 320GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 106MB 105MB fat32 EFI system partition boot 2 106MB 240MB 134MB Microsoft reserved partition msftres 3 240MB 87.2GB 87.0GB ntfs Basic data partition 4 87.2GB 169GB 81.9GB ext4 5 169GB 316GB 147GB ext4 6 316GB 320GB 4096MB linux-swap(v1) =================== MOUNT: /dev/sda4 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot/efi type vfat (rw) /dev/sda5 on /home type ext4 (rw) gvfs-fuse-daemon on /home/vierlex/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=vierlex) /dev/sda3 on /mnt/boot-sav/sda3 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /sys/block/sda: alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda3 sda4 sda5 sda6 size slaves stat subsystem trace uevent /dev: agpgart autofs block bsg btrfs-control bus char console core cpu cpu_dma_latency disk dri ecryptfs fb0 fd full fuse hpet input kmsg log mapper mcelog mei mem net network_latency network_throughput null oldmem port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda3 sda4 sda5 sda6 sg0 shm snapshot snd stderr stdin stdout tpm0 uinput urandom usbmon0 usbmon1 usbmon2 v4l vga_arbiter video0 watchdog zero /dev/mapper: control /boot/efi: EFI /boot/efi/EFI: Boot Microsoft ubuntu /boot/efi/efi: Boot Microsoft ubuntu /boot/efi/efi/Boot: bootx64.efi /boot/efi/efi/ubuntu: grubx64.efi WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. =================== DF: Filesystem Type Size Used Avail Use% Mounted on /dev/sda4 ext4 77G 4.1G 69G 6% / udev devtmpfs 3.9G 12K 3.9G 1% /dev tmpfs tmpfs 1.6G 864K 1.6G 1% /run none tmpfs 5.0M 0 5.0M 0% /run/lock none tmpfs 3.9G 152K 3.9G 1% /run/shm /dev/sda1 vfat 96M 18M 79M 19% /boot/efi /dev/sda5 ext4 137G 2.2G 128G 2% /home /dev/sda3 fuseblk 81G 30G 52G 37% /mnt/boot-sav/sda3 =================== FDISK: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf34fe538 Device Boot Start End Blocks Id System /dev/sda1 1 625142447 312571223+ ee GPT =================== Before mainwindow FSCK no PASTEBIN yes WUBI no WINBOOT yes recommendedrepair, purge, QTY_OF_PART_FOR_REINSTAL 1 no-kernel-purge UNHIDEBOOT_ACTION yes (10s), noflag () PART_TO_REINSTALL_GRUB sda4, FORCE_GRUB no (sda) REMOVABLEDISK no USE_SEPARATEBOOTPART no (sda3) grub2 () UNCOMMENT_GFXMODE no ATA ADD_KERNEL_OPTION no (acpi=off) MBR_TO_RESTORE ( ) EFI detected. Please check the options. =================== Actions FSCK no PASTEBIN yes WUBI no WINBOOT no bootinfo, nombraction, QTY_OF_PART_FOR_REINSTAL 1 no-kernel-purge UNHIDEBOOT_ACTION no (10s), noflag () PART_TO_REINSTALL_GRUB sda4, FORCE_GRUB no (sda) REMOVABLEDISK no USE_SEPARATEBOOTPART no (sda3) grub2 () UNCOMMENT_GFXMODE no ATA ADD_KERNEL_OPTION no (acpi=off) MBR_TO_RESTORE ( ) No change has been performed on your computer. See you soon! internet: connected Thanks for your time and attention. EDIT: additional Info Request =No boot loader is installed in the MBR of /dev/sda. But maybe this is how it is supposed to work? yea this is ok. boot stuff seems to be on a seperate partition, in my case sda1. I'm very new to this UEFI thing too. missing files like bootmgr i don't really have a clue :D but yea, maybe thats how it suppose to be? Instead and whats not shown in the log for some reason: There is additional microsoft bootfiles on sda1 under /efi/microsoft/ [much stuff] I remember also doing some kind of hack to make a UEFI windows 7 usb stick. http://jake.io/b/2011/installing-windows-7-with-uefi-boot-on-an-x220-from-usb/ In short: creating and placing bootx64.efi on the stick so it can be booted in UEFI mode. boot order i decide that in my BIOS. i read somwhere that the thinkpad x220 (essential part of the serial number: 4921 http://www.lenovo.com/shop/americas/content/user_guides/x220_x220i_x220tablet_x220itablet_ug_en.pdf) doesnt really have UEFI interface or something, still, these 2 options are listed with all the other usual devices you can give a boot priority to. Right now it looks like this: Boot Priority Order 1. ubuntu 2. Windows Boot Manager 3. USB FDD 4. USB HDD 5. ATA HDD0 HITACHI [random string]

  Read the article

• Configuring Oracle iPlanet WebServer / Oracle Traffic Director to use crypto accelerators on T4-1 servers

  - by mv

  Configuring Oracle iPlanet Web Server / Oracle Traffic Director to use crypto accelerators on T4-1 servers Jyri had written a technical article on Configuring Solaris Cryptographic Framework and Sun Java System Web Server 7 on Systems With UltraSPARC T1 Processors. I tried to find out what has changed since then in T4. I have used a T4-1 SPARC system with Solaris 10. Results slightly vary for Solaris 11.  For Solaris 11, the T4 optimization was implemented in libsoftcrypto.so while it was in pkcs11_softtoken_extra.so for Solaris 10. Overview of T4 processors is here in this blog. Many thanx to Chi-Chang Lin and Julien for their help. 1. Install Oracle iPlanet Web Server / Oracle Traffic Director.  Go to instance/config directory.  # cd /opt/oracle/webserver7/https-hostname.fqdn/config 2. List default PKCS#11 Modules # ../../bin/modutil -dbdir . -listListing of PKCS #11 Modules-----------------------------------------------------------1. NSS Internal PKCS #11 Moduleslots: 2 slots attachedstatus: loadedslot: NSS Internal Cryptographic Servicestoken: NSS Generic Crypto Servicesslot: NSS User Private Key and Certificate Servicestoken: NSS Certificate DB2. Root Certslibrary name: libnssckbi.soslots: 1 slot attachedstatus: loadedslot: NSS Builtin Objectstoken: Builtin Object Token----------------------------------------------------------- 3. Initialize the soft token data store in the $HOME/.sunw/pkcs11_softtoken/ directory # pktool setpin keystore=pkcs11Enter token passphrase: olderpasswordCreate new passphrase: passwordRe-enter new passphrase: passwordPassphrase changed. 4. Offload crypto operations to Solaris Crypto Framework on T4 $ ../../bin/modutil -dbdir . -nocertdb -add SCF -libfile /usr/lib/libpkcs11.so -mechanisms RSA:AES:SHA1:MD5 Module "SCF" added to database. Note that -nocertdb means modutil won't try to open the NSS softoken key database. It doesn't even have to be present. PKCS#11 library used is /usr/lib/libpkcs11.so. If the server is running in 64 bit mode, we have to use /usr/lib/64/libpkcs11.so Unlike T1 and T2, in T4 we do not have to disable mechanisms in softtoken provider using cryptoadm. 5. List again to check that a new module SCF is added # ../../bin/modutil -dbdir . -list Listing of PKCS #11 Modules-----------------------------------------------------------1. NSS Internal PKCS #11 Moduleslots: 2 slots attachedstatus: loadedslot: NSS Internal Cryptographic Servicestoken: NSS Generic Crypto Servicesslot: NSS User Private Key and Certificate Servicestoken: NSS Certificate DB2. SCFlibrary name: /usr/lib/libpkcs11.soslots: 2 slots attachedstatus: loadedslot: Sun Metaslottoken: Sun Metaslotslot: n2rng/0 SUNW_N2_Random_Number_Generator token: n2rng/0 SUNW_N2_RNG 3. Root Certs library name: libnssckbi.so slots: 1 slot attached status: loaded slot: NSS Builtin Objects token: Builtin Object Token----------------------------------------------------------- 6.  Create certificate in “Sun Metaslot” : I have used certutil, but you must use Admin Server CLI / GUI # ../../bin/certutil -S -x -n "Server-Cert" -t "CT,CT,CT" -s "CN=*.fqdn" -d . -h "Sun Metaslot"Enter Password or Pin for "Sun Metaslot": password 7. Verify that the certificate is created properly in “Sun Metslaot” # ../../bin/certutil -L -d . -h "Sun Metaslot"Certificate Nickname Trust AttributesSSL,S/MIME,JAR/XPIEnter Password or Pin for "Sun Metaslot": passwordSun Metaslot:Server-Cert CTu,Cu,Cu# 8. Associate this newly created certificate to http listener using Admin CLI/GUI. After that server.xml should have <http-listener> ...    <ssl>        <server-cert-nickname>Sun Metaslot:Server-Cert</server-cert-nicknamer>    </ssl> Note the prefix "Sun Metaslot" 9. Disable PKCS#11 bypass To use the accelerated AES algorithm, turn off PKCS#11 bypass, and configure modutil to have the AES mechanism go to the Metaslot. After you disable PKCS#11 bypasss using Admin GUI/CLI,  check that server.xml should have <server> ....    <pkcs11>         <enabled>1</enabled>         <allow-bypass>0</allow-bypass>     </pkcs11> With PKCS#11 bypass enabled, Oracle iPlanet Web Server will only use the RSA capability of the T4, provided certificate and key are stored in the T4 slot (Metaslot). Actually, the RSA op is never bypassed in NSS, it's always done with PKCS#11 calls. So the bypass settings won't affect the behavior of the probes for RSA at all. The only thing that matters if where the RSA key and certificate live, ie. which PKCS#11 token, and thus which PKCS#11 module gets called to do the work. If your certificate/key are in the NSS certificate/key db, you will see libsoftokn3/libfreebl libraries doing the RSA work. If they are in the Sun Metaslot, it should be the Solaris code. 10. Start the server instance # ../bin/startserv Oracle iPlanet Web Server 7.0.16 B09/14/2012 03:33Please enter the PIN for the "Sun Metaslot" token: password...info: HTTP3072: http-listener-1: https://hostname.fqdn:80 ready to accept requestsinfo: CORE3274: successful server startup 11. Figure out which process to run this DTrace script on # ps -eaf | grep webservd | grep -v dogwebservd 18224 18223 0 13:17:25 ? 0:07 webservd -d /opt/oracle/webserver7/https-hostname.fqdn/config -r /opt/root 18225 18224 0 13:17:25 ? 0:00 webservd -d /opt/oracle/webserver7/https-hostname.fqdn/config -r /opt/ (For Oracle Traffic Director look for process named "trafficd") We see that the child process id is “18225” 12. Clients for testing : You can use any browser. I used NSS tool tstclnt for testing $cat > req.txtGET /index.html HTTP/1.0 For checking both RSA and AES, I used cipher “:0035” which is TLS_RSA_WITH_AES_256_CBC_SHA $./tstclnt -h hostname -p 80 -d . -T -f -o -v -c “:0035” < req.txt 13. How do I make sure that crypto accelerator is being used 13.1 Create DTrace script The following D script should be able to uncover whether T4-specific crypto routine are being called or not. It also displays stats per second. # cat > t4crypto.d#!/usr/sbin/dtrace -spid$target::*rsa*:entry,pid$target::*yf*:entry{    @ops[probemod, probefunc] = count();}tick-1sec{    printa(@ops);    trunc(@ops);} Invoke with './t4crypto.d -p <pid> ' 13.2 EXPECTED PROBES FOR Solaris 10 : If offloading to T4 HW are correctly set up, the expected DTrace output would have these probes and libraries library Operations PROBES pkcs11_softtoken_extra.so RSA soft_decrypt_rsa_pkcs_decode, soft_encrypt_rsa_pkcs_encode soft_rsa_crypt_init_common soft_rsa_decrypt, soft_rsa_encrypt soft_rsa_decrypt_common, soft_rsa_encrypt_common AES yf_aes_instructions_present yf_aes_expand256, yf_aes256_cbc_decrypt, yf_aes256_cbc_encrypt, yf_aes256_load_keys_for_decrypt, yf_aes256_load_keys_for_encrypt, Note that these are for 256, same for 128, 192... these are for cbc, same for ecb, ctr, cfb128... DES yf_des_expand, yf_des_instructions_present yf_des_encrypt libmd_psr.so MD5 yf_md5_multiblock, yf_md5_instruction_present SHA1 yf_sha1_instruction_present, yf_sha1_multibloc 13.3 SAMPLE OUTPUT FOR CIPHER TLS_RSA_WITH_AES_256_CBC_SHA (0x0035) ON T4 SPARC SOLARIS 10 WITHOUT PKCS#11 BYPASS # ./t4crypto.d -p 18225 pkcs11_softtoken_extra.so.1   soft_decrypt_rsa_pkcs_decode    1 pkcs11_softtoken_extra.so.1   soft_rsa_crypt_init_common      1 pkcs11_softtoken_extra.so.1   soft_rsa_decrypt                1 pkcs11_softtoken_extra.so.1   big_mp_mul_yf                   2 pkcs11_softtoken_extra.so.1   mpm_yf_mpmul                    2 pkcs11_softtoken_extra.so.1   mpmul_arr_yf                    2 pkcs11_softtoken_extra.so.1   rijndael_key_setup_enc_yf       2 pkcs11_softtoken_extra.so.1   soft_rsa_decrypt_common         2 pkcs11_softtoken_extra.so.1   yf_aes_expand256                2 pkcs11_softtoken_extra.so.1   yf_aes256_cbc_decrypt           3 pkcs11_softtoken_extra.so.1   yf_aes256_load_keys_for_decrypt 3 pkcs11_softtoken_extra.so.1   big_mont_mul_yf                 6 pkcs11_softtoken_extra.so.1   mm_yf_montmul                   6 pkcs11_softtoken_extra.so.1   yf_des_instructions_present     6 pkcs11_softtoken_extra.so.1   yf_aes256_cbc_encrypt           8 pkcs11_softtoken_extra.so.1   yf_aes256_load_keys_for_encrypt 8 pkcs11_softtoken_extra.so.1   yf_mpmul_present                8 pkcs11_softtoken_extra.so.1   yf_aes_instructions_present    13 pkcs11_softtoken_extra.so.1   yf_des_encrypt                 18 libmd_psr.so.1                yf_md5_multiblock              41 libmd_psr.so.1                yf_md5_instruction_present     72 libmd_psr.so.1                yf_sha1_instruction_present    82 libmd_psr.so.1                yf_sha1_multiblock             82 This indicates that both RSA and AES ops are done in Solaris Crypto Framework. 13.4 SAMPLE OUTPUT FOR CIPHER TLS_RSA_WITH_AES_256_CBC_SHA (0x0035) ON T4 SPARC SOLARIS 10 WITH PKCS#11 BYPASS # ./t4crypto.d -p 18225 pkcs11_softtoken_extra.so.1   soft_decrypt_rsa_pkcs_decode 1 pkcs11_softtoken_extra.so.1   soft_rsa_crypt_init_common   1 pkcs11_softtoken_extra.so.1   soft_rsa_decrypt             1 pkcs11_softtoken_extra.so.1   soft_rsa_decrypt_common      1 pkcs11_softtoken_extra.so.1   big_mp_mul_yf                2 pkcs11_softtoken_extra.so.1   mpm_yf_mpmul                 2 pkcs11_softtoken_extra.so.1   mpmul_arr_yf                 2 pkcs11_softtoken_extra.so.1   big_mont_mul_yf              6 pkcs11_softtoken_extra.so.1   mm_yf_montmul                6 pkcs11_softtoken_extra.so.1   yf_mpmul_present             8 For this cipher, when I enable PKCS#11 bypass, Only RSA probes are being hit AES probes are not being hit. 13.5 ustack() for RSA operations / probefunc == "soft_rsa_decrypt" / Shows that libnss3.so is calling C_* functions of libpkcs11.so which is calling functions of pkcs11_softtoken_extra.so for both cases with and without bypass. When PKCS#11 bypass is disabled (allow-bypass is 0) pkcs11_softtoken_extra.so.1`soft_rsa_decrypt pkcs11_softtoken_extra.so.1`soft_rsa_decrypt_common+0x94 pkcs11_softtoken_extra.so.1`soft_unwrapkey+0x258 pkcs11_softtoken_extra.so.1`C_UnwrapKey+0x1ec libpkcs11.so.1`meta_unwrap_key+0x17c libpkcs11.so.1`meta_UnwrapKey+0xc4 libpkcs11.so.1`C_UnwrapKey+0xfc libnss3.so`pk11_AnyUnwrapKey+0x6b8 libnss3.so`PK11_PubUnwrapSymKey+0x8c libssl3.so`ssl3_HandleRSAClientKeyExchange+0x1a0 libssl3.so`ssl3_HandleClientKeyExchange+0x154 libssl3.so`ssl3_HandleHandshakeMessage+0x440 libssl3.so`ssl3_HandleHandshake+0x11c libssl3.so`ssl3_HandleRecord+0x5e8 libssl3.so`ssl3_GatherCompleteHandshake+0x5c libssl3.so`ssl_GatherRecord1stHandshake+0x30 libssl3.so`ssl_Do1stHandshake+0xec libssl3.so`ssl_SecureRecv+0x1c8 libssl3.so`ssl_Recv+0x9c libns-httpd40.so`__1cNDaemonSessionDrun6M_v_+0x2dc When PKCS#11 bypass is enabled (allow-bypass is 1) pkcs11_softtoken_extra.so.1`soft_rsa_decrypt pkcs11_softtoken_extra.so.1`soft_rsa_decrypt_common+0x94 pkcs11_softtoken_extra.so.1`C_Decrypt+0x164 libpkcs11.so.1`meta_do_operation+0x27c libpkcs11.so.1`meta_Decrypt+0x4c libpkcs11.so.1`C_Decrypt+0xcc libnss3.so`PK11_PrivDecryptPKCS1+0x1ac libssl3.so`ssl3_HandleRSAClientKeyExchange+0xe4 libssl3.so`ssl3_HandleClientKeyExchange+0x154 libssl3.so`ssl3_HandleHandshakeMessage+0x440 libssl3.so`ssl3_HandleHandshake+0x11c libssl3.so`ssl3_HandleRecord+0x5e8 libssl3.so`ssl3_GatherCompleteHandshake+0x5c libssl3.so`ssl_GatherRecord1stHandshake+0x30 libssl3.so`ssl_Do1stHandshake+0xec libssl3.so`ssl_SecureRecv+0x1c8 libssl3.so`ssl_Recv+0x9c libns-httpd40.so`__1cNDaemonSessionDrun6M_v_+0x2dc libnsprwrap.so`ThreadMain+0x1c libnspr4.so`_pt_root+0xe8 13.6 ustack() FOR AES operations / probefunc == "yf_aes256_cbc_encrypt" / When PKCS#11 bypass is disabled (allow-bypass is 0) pkcs11_softtoken_extra.so.1`yf_aes256_cbc_encrypt pkcs11_softtoken_extra.so.1`aes_block_process_contiguous_whole_blocks+0xb4 pkcs11_softtoken_extra.so.1`aes_crypt_contiguous_blocks+0x1cc pkcs11_softtoken_extra.so.1`soft_aes_encrypt_common+0x22c pkcs11_softtoken_extra.so.1`C_EncryptUpdate+0x10c libpkcs11.so.1`meta_do_operation+0x1fc libpkcs11.so.1`meta_EncryptUpdate+0x4c libpkcs11.so.1`C_EncryptUpdate+0xcc libnss3.so`PK11_CipherOp+0x1a0 libssl3.so`ssl3_CompressMACEncryptRecord+0x264 libssl3.so`ssl3_SendRecord+0x300 libssl3.so`ssl3_FlushHandshake+0x54 libssl3.so`ssl3_SendFinished+0x1fc libssl3.so`ssl3_HandleFinished+0x314 libssl3.so`ssl3_HandleHandshakeMessage+0x4ac libssl3.so`ssl3_HandleHandshake+0x11c libssl3.so`ssl3_HandleRecord+0x5e8 libssl3.so`ssl3_GatherCompleteHandshake+0x5c libssl3.so`ssl_GatherRecord1stHandshake+0x30 libssl3.so`ssl_Do1stHandshake+0xec Shows that libnss3.so is calling C_* functions of libpkcs11.so which is calling functions of pkcs11_softtoken_extra.so However when PKCS#11 bypass is disabled (allow-bypass is 1) this stack isn't getting called. 14. LIST OF ALL THE PROBES MATCHED BY D SCRIPT FOR REFERENCE # ./t4crypto.d -p 18225 -l ID PROVIDER MODULE FUNCTION NAME ... 55720 pid18225 libmd_psr.so.1 yf_md5_instruction_present entry 55721 pid18225 libmd_psr.so.1 yf_sha256_instruction_present entry 55722 pid18225 libmd_psr.so.1 yf_sha512_instruction_present entry 55723 pid18225 libmd_psr.so.1 yf_sha1_instruction_present entry 55724 pid18225 libmd_psr.so.1 yf_sha256 entry 55725 pid18225 libmd_psr.so.1 yf_sha256_multiblock entry 55726 pid18225 libmd_psr.so.1 yf_sha512 entry 55727 pid18225 libmd_psr.so.1 yf_sha512_multiblock entry 55728 pid18225 libmd_psr.so.1 yf_sha1 entry 55729 pid18225 libmd_psr.so.1 yf_sha1_multiblock entry 55730 pid18225 libmd_psr.so.1 yf_md5 entry 55731 pid18225 libmd_psr.so.1 yf_md5_multiblock entry 55732 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_instructions_present entry 55733 pid18225 pkcs11_softtoken_extra.so.1 rijndael_key_setup_enc_yf entry 55734 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_expand128 entry 55735 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_encrypt128 entry 55736 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_decrypt128 entry 55737 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_expand192 entry 55738 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_encrypt192 entry 55739 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_decrypt192 entry 55740 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_expand256 entry 55741 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_encrypt256 entry 55742 pid18225 pkcs11_softtoken_extra.so.1 yf_aes_decrypt256 entry 55743 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_load_keys_for_encrypt entry 55744 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_load_keys_for_encrypt entry 55745 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_load_keys_for_encrypt entry 55746 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_ecb_encrypt entry 55747 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_ecb_encrypt entry 55748 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_ecb_encrypt entry 55749 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_cbc_encrypt entry 55750 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_cbc_encrypt entry 55751 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_cbc_encrypt entry 55752 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_ctr_crypt entry 55753 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_ctr_crypt entry 55754 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_ctr_crypt entry 55755 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_cfb128_encrypt entry 55756 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_cfb128_encrypt entry 55757 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_cfb128_encrypt entry 55758 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_load_keys_for_decrypt entry 55759 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_load_keys_for_decrypt entry 55760 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_load_keys_for_decrypt entry 55761 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_ecb_decrypt entry 55762 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_ecb_decrypt entry 55763 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_ecb_decrypt entry 55764 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_cbc_decrypt entry 55765 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_cbc_decrypt entry 55766 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_cbc_decrypt entry 55767 pid18225 pkcs11_softtoken_extra.so.1 yf_aes128_cfb128_decrypt entry 55768 pid18225 pkcs11_softtoken_extra.so.1 yf_aes192_cfb128_decrypt entry 55769 pid18225 pkcs11_softtoken_extra.so.1 yf_aes256_cfb128_decrypt entry 55771 pid18225 pkcs11_softtoken_extra.so.1 yf_des_instructions_present entry 55772 pid18225 pkcs11_softtoken_extra.so.1 yf_des_expand entry 55773 pid18225 pkcs11_softtoken_extra.so.1 yf_des_encrypt entry 55774 pid18225 pkcs11_softtoken_extra.so.1 yf_mpmul_present entry 55775 pid18225 pkcs11_softtoken_extra.so.1 yf_montmul_present entry 55776 pid18225 pkcs11_softtoken_extra.so.1 mm_yf_montmul entry 55777 pid18225 pkcs11_softtoken_extra.so.1 mm_yf_montsqr entry 55778 pid18225 pkcs11_softtoken_extra.so.1 mm_yf_restore_func entry 55779 pid18225 pkcs11_softtoken_extra.so.1 mm_yf_ret_from_mont_func entry 55780 pid18225 pkcs11_softtoken_extra.so.1 mm_yf_execute_slp entry 55781 pid18225 pkcs11_softtoken_extra.so.1 big_modexp_ncp_yf entry 55782 pid18225 pkcs11_softtoken_extra.so.1 big_mont_mul_yf entry 55783 pid18225 pkcs11_softtoken_extra.so.1 mpmul_arr_yf entry 55784 pid18225 pkcs11_softtoken_extra.so.1 big_mp_mul_yf entry 55785 pid18225 pkcs11_softtoken_extra.so.1 mpm_yf_mpmul entry 55786 pid18225 libns-httpd40.so nsapi_rsa_set_priv_fn entry ... 55795 pid18225 libnss3.so prepare_rsa_priv_key_export_for_asn1 entry 55796 pid18225 libresolv.so.2 sunw_dst_rsaref_init entry 55797 pid18225 libnssutil3.so NSS_Get_SEC_UniversalStringTemplate entry ... 55813 pid18225 libsoftokn3.so prepare_low_rsa_priv_key_for_asn1 entry 55814 pid18225 libsoftokn3.so rsa_FormatOneBlock entry 55815 pid18225 libsoftokn3.so rsa_FormatBlock entry 55816 pid18225 libnssdbm3.so lg_prepare_low_rsa_priv_key_for_asn1 entry 55817 pid18225 libfreebl_32fpu_3.so rsa_build_from_primes entry 55818 pid18225 libfreebl_32fpu_3.so rsa_is_prime entry 55819 pid18225 libfreebl_32fpu_3.so rsa_get_primes_from_exponents entry 55820 pid18225 libfreebl_32fpu_3.so rsa_PrivateKeyOpNoCRT entry 55821 pid18225 libfreebl_32fpu_3.so rsa_PrivateKeyOpCRTNoCheck entry 55822 pid18225 libfreebl_32fpu_3.so rsa_PrivateKeyOpCRTCheckedPubKey entry 55823 pid18225 pkcs11_kernel.so.1 key_gen_rsa_by_value entry 55824 pid18225 pkcs11_kernel.so.1 get_rsa_private_key entry 55825 pid18225 pkcs11_kernel.so.1 get_rsa_public_key entry 55826 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_encrypt entry 55827 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_decrypt entry 55828 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_crypt_init_common entry 55829 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_encrypt_common entry 55830 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_decrypt_common entry 55831 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_sign_verify_init_common entry 55832 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_sign_common entry 55833 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_verify_common entry 55834 pid18225 pkcs11_softtoken_extra.so.1 generate_rsa_key entry 55835 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_genkey_pair entry 55836 pid18225 pkcs11_softtoken_extra.so.1 get_rsa_sha1_prefix entry 55837 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_digest_sign_common entry 55838 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_digest_verify_common entry 55839 pid18225 pkcs11_softtoken_extra.so.1 soft_rsa_verify_recover entry 55840 pid18225 pkcs11_softtoken_extra.so.1 rsa_pri_to_asn1 entry 55841 pid18225 pkcs11_softtoken_extra.so.1 asn1_to_rsa_pri entry 55842 pid18225 pkcs11_softtoken_extra.so.1 soft_encrypt_rsa_pkcs_encode entry 55843 pid18225 pkcs11_softtoken_extra.so.1 soft_decrypt_rsa_pkcs_decode entry 55844 pid18225 pkcs11_softtoken_extra.so.1 soft_sign_rsa_pkcs_encode entry 55845 pid18225 pkcs11_softtoken_extra.so.1 soft_verify_rsa_pkcs_decode entry 55770 profile tick-1sec

  Read the article

• How to remove the hint in the terminal?

  - by jiangchengwu

  As a normal user , when I run some command like ps\netstat, the terminal hint me: (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) I know could redirect STDERR to /dev/null can remove this hint. But I want to know is there any way to remove it , such as edit some configuration files ? [deploy@storage2 ~]$ ps -V (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) procps version 3.2.7 [deploy@storage2 ~]$ ps -V 2>/dev/null procps version 3.2.7 My OS info: [deploy@storage2 ~]$ uname -a Linux storage2 2.6.18-243.el5 #1 SMP Mon Feb 7 18:47:27 EST 2011 x86_64 x86_64 x86_64 GNU/Linux [deploy@storage2 ~]$ lsb_release LSB Version: :core-3.1-amd64:core-3.1-ia32:core-3.1-noarch:graphics-3.1-amd64:graphics-3.1-ia32:graphics-3.1-noarch [deploy@storage2 ~]$ netstat -V (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) net-tools 1.60 netstat 1.42 (2001-04-15) Fred Baumgarten, Alan Cox, Bernd Eckenfels, Phil Blundell, Tuan Hoang and others +NEW_ADDRT +RTF_IRTT +RTF_REJECT +FW_MASQUERADE +I18N AF: (inet) +UNIX +INET +INET6 +IPX +AX25 +NETROM +X25 +ATALK +ECONET +ROSE HW: +ETHER +ARC +SLIP +PPP +TUNNEL +TR +AX25 +NETROM +X25 +FR +ROSE +ASH +SIT +FDDI +HIPPI +HDLC/LAPB There are more info from strace: [deploy@storage2 ~]$ strace ps -V execve("/bin/ps", ["ps", "-V"], [/* 27 vars */]) = 0 brk(0) = 0x929a000 access("/etc/ld.so.preload", R_OK) = -1 ENOENT (No such file or directory) open("/etc/ld.so.cache", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=99752, ...}) = 0 mmap2(NULL, 99752, PROT_READ, MAP_PRIVATE, 3, 0) = 0xfffffffff7fde000 close(3) = 0 open("/lib/libnsl.so.1", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0 \241\210\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=101404, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7fdd000 mmap2(0x887000, 92104, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x887000 mmap2(0x89a000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x12) = 0x89a000 mmap2(0x89c000, 6088, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x89c000 close(3) = 0 open("/lib/libdl.so.2", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0Pzt\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=16428, ...}) = 0 mmap2(0x747000, 12408, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x747000 mmap2(0x749000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x1) = 0x749000 close(3) = 0 open("/lib/libm.so.6", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\20\204p\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=208352, ...}) = 0 mmap2(0x705000, 155760, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x705000 mmap2(0x72a000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x24) = 0x72a000 close(3) = 0 open("/lib/libcrypt.so.1", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\340\246q\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=45288, ...}) = 0 mmap2(0x71a000, 201020, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xfffffffff7fab000 mmap2(0xf7fb4000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x8) = 0xfffffffff7fb4000 mmap2(0xf7fb6000, 155964, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7fb6000 close(3) = 0 open("/lib/libutil.so.1", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0 \n\0\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=13420, ...}) = 0 mmap2(NULL, 12428, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xfffffffff7fa7000 mmap2(0xf7fa9000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x1) = 0xfffffffff7fa9000 close(3) = 0 open("/lib/libpthread.so.0", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0@(s\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=129716, ...}) = 0 mmap2(0x72e000, 90596, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x72e000 mmap2(0x741000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x13) = 0x741000 mmap2(0x743000, 4580, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x743000 close(3) = 0 open("/lib/libc.so.6", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\340?]\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=1611564, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7fa6000 mmap2(0x5be000, 1328580, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x5be000 mmap2(0x6fd000, 12288, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x13f) = 0x6fd000 mmap2(0x700000, 9668, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x700000 close(3) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7fa5000 set_thread_area(0xffd61bb4) = 0 mprotect(0x6fd000, 8192, PROT_READ) = 0 mprotect(0x741000, 4096, PROT_READ) = 0 mprotect(0xf7fa9000, 4096, PROT_READ) = 0 mprotect(0xf7fb4000, 4096, PROT_READ) = 0 mprotect(0x72a000, 4096, PROT_READ) = 0 mprotect(0x749000, 4096, PROT_READ) = 0 mprotect(0x89a000, 4096, PROT_READ) = 0 mprotect(0x5ba000, 4096, PROT_READ) = 0 munmap(0xf7fde000, 99752) = 0 set_tid_address(0xf7fa5708) = 20214 set_robust_list(0xf7fa5710, 0xc) = 0 futex(0xffd61f74, FUTEX_WAKE_PRIVATE, 1) = 0 rt_sigaction(SIGRTMIN, {0x4007323d0, [], 0}, NULL, 8) = 0 rt_sigaction(SIGRT_1, {0x10000004007322e0, [], 0}, NULL, 8) = 0 rt_sigprocmask(SIG_UNBLOCK, [RTMIN RT_1], NULL, 8) = 0 getrlimit(RLIMIT_STACK, {rlim_cur=-4284481536, rlim_max=67108864*1024}) = 0 uname({sys="Linux", node="storage2", ...}) = 0 readlink("/proc/self/exe", "/bin/ps"..., 260) = 7 brk(0) = 0x929a000 brk(0x92bb000) = 0x92bb000 open("/bin/ps", O_RDONLY|O_LARGEFILE) = 3 _llseek(3, -12, [711660], SEEK_END) = 0 read(3, "\274U!\253\2\0\0\0\224\237\t\0", 12) = 12 mmap2(NULL, 634880, PROT_READ, MAP_SHARED, 3, 0x13) = 0xfffffffff7f0a000 mmap2(NULL, 630784, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7e70000 close(3) = 0 futex(0x74a06c, FUTEX_WAKE_PRIVATE, 2147483647) = 0 geteuid32() = 501 socket(PF_FILE, SOCK_STREAM, 0) = 3 fcntl64(3, F_SETFL, O_RDWR|O_NONBLOCK) = 0 connect(3, {sa_family=AF_FILE, path="/var/run/nscd/socket"...}, 110) = -1 ENOENT (No such file or directory) close(3) = 0 socket(PF_FILE, SOCK_STREAM, 0) = 3 fcntl64(3, F_SETFL, O_RDWR|O_NONBLOCK) = 0 connect(3, {sa_family=AF_FILE, path="/var/run/nscd/socket"...}, 110) = -1 ENOENT (No such file or directory) close(3) = 0 open("/etc/nsswitch.conf", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=1696, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7ff6000 read(3, "#\n# /etc/nsswitch.conf\n#\n# An ex"..., 4096) = 1696 read(3, "", 4096) = 0 close(3) = 0 munmap(0xf7ff6000, 4096) = 0 open("/etc/ld.so.cache", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=99752, ...}) = 0 mmap2(NULL, 99752, PROT_READ, MAP_PRIVATE, 3, 0) = 0xfffffffff7fde000 close(3) = 0 open("/lib/libnss_files.so.2", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\300\30\0\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=46680, ...}) = 0 mmap2(NULL, 41616, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xfffffffff7e65000 mmap2(0xf7e6e000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x8) = 0xfffffffff7e6e000 close(3) = 0 mprotect(0xf7e6e000, 4096, PROT_READ) = 0 munmap(0xf7fde000, 99752) = 0 open("/etc/passwd", O_RDONLY) = 3 fcntl64(3, F_GETFD) = 0 fcntl64(3, F_SETFD, FD_CLOEXEC) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=2166, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7ff6000 read(3, "root:x:0:0:root:/root:/bin/bash\n"..., 4096) = 2166 close(3) = 0 munmap(0xf7ff6000, 4096) = 0 mkdir("/tmp/pdk-deploy/", 0755) = -1 EEXIST (File exists) mkdir("/tmp/pdk-deploy/fcb734befe617ec3ae1edc38da810a5a", 0755) = -1 EEXIST (File exists) open("/tmp/pdk-deploy/fcb734befe617ec3ae1edc38da810a5a/libperl.so", O_RDONLY|O_LARGEFILE) = 3 close(3) = 0 open("/tmp/pdk-deploy/fcb734befe617ec3ae1edc38da810a5a/libperl.so", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\300!\2\0004\0\0\0"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0664, st_size=1264090, ...}) = 0 mmap2(NULL, 1140104, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xfffffffff7d4e000 mmap2(0xf7e5a000, 45056, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x10b) = 0xfffffffff7e5a000 close(3) = 0 rt_sigaction(SIGFPE, {0x1000000000000001, [], SA_RESTORER|SA_STACK|SA_RESTART|SA_INTERRUPT|SA_NODEFER|SA_RESETHAND|SA_SIGINFO|0x3d61cb8, (nil)}, {SIG_DFL, ~[HUP INT ILL ABRT BUS SEGV USR2 PIPE ALRM TERM STOP TSTP TTIN TTOU XCPU WINCH IO PWR SYS RTMIN RT_1 RT_2 RT_4 RT_5 RT_8 RT_9 RT_11 RT_12 RT_13 RT_16 RT_17 RT_18 RT_22 RT_24 RT_25 RT_26 RT_27 RT_28 RT_29 RT_30 RT_31], SA_RESTART|SA_RESETHAND|0x22302d0}, 8) = 0 getuid32() = 501 geteuid32() = 501 getgid32() = 502 getegid32() = 502 open("/usr/lib/locale/locale-archive", O_RDONLY|O_LARGEFILE) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=56454896, ...}) = 0 mmap2(NULL, 2097152, PROT_READ, MAP_PRIVATE, 3, 0) = 0xfffffffff7b4e000 mmap2(NULL, 241664, PROT_READ, MAP_PRIVATE, 3, 0x13ec) = 0xfffffffff7b13000 mmap2(NULL, 4096, PROT_READ, MAP_PRIVATE, 3, 0x1466) = 0xfffffffff7b12000 close(3) = 0 mmap2(NULL, 135168, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xfffffffff7af1000 time(NULL) = 1348210009 readlink("/proc/self/exe", "/bin/ps"..., 4095) = 7 ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig icanon echo ...}) = 0 _llseek(0, 0, 0xffd618d0, SEEK_CUR) = -1 ESPIPE (Illegal seek) ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd618a8) = -1 EINVAL (Invalid argument) _llseek(1, 0, 0xffd618d0, SEEK_CUR) = -1 ESPIPE (Illegal seek) ioctl(2, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd618a8) = -1 EINVAL (Invalid argument) _llseek(2, 0, 0xffd618d0, SEEK_CUR) = -1 ESPIPE (Illegal seek) open("/dev/null", O_RDONLY|O_LARGEFILE) = 3 ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd61978) = -1 ENOTTY (Inappropriate ioctl for device) _llseek(3, 0, [0], SEEK_CUR) = 0 fcntl64(3, F_SETFD, FD_CLOEXEC) = 0 rt_sigaction(SIGCHLD, NULL, {SIG_DFL, [], SA_RESTART|SA_RESETHAND|0x22302d0}, 8) = 0 brk(0x92dc000) = 0x92dc000 getppid() = 20212 stat64("/opt/ActivePerl-5.8/site/lib/sitecustomize.pl", 0xffd61560) = -1 ENOENT (No such file or directory) close(3) = 0 open("/usr/lib/.khostd/.hostconf", O_RDONLY|O_LARGEFILE) = 3 ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd61828) = -1 ENOTTY (Inappropriate ioctl for device) _llseek(3, 0, [0], SEEK_CUR) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=334, ...}) = 0 fcntl64(3, F_SETFD, FD_CLOEXEC) = 0 read(3, "bindport=9001\ntrustip=221.122.57"..., 4096) = 334 read(3, "", 4096) = 0 close(3) = 0 pipe([3, 4]) = 0 pipe([5, 6]) = 0 clone(child_stack=0, flags=CLONE_CHILD_CLEARTID|CLONE_CHILD_SETTID|SIGCHLD, child_tidptr=0) = 20215 close(6) = 0 close(4) = 0 read(5, "", 4) = 0 close(5) = 0 ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd61868) = -1 EINVAL (Invalid argument) _llseek(3, 0, 0xffd61890, SEEK_CUR) = -1 ESPIPE (Illegal seek) fstat64(3, {st_mode=S_IFIFO|0600, st_size=0, ...}) = 0 read(3, (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) "tcp 0 0 0.0.0.0:9001"..., 4096) = 109 read(3, "", 4096) = 0 --- SIGCHLD (Child exited) @ 0 (0) --- fstat64(3, {st_mode=S_IFIFO|0600, st_size=0, ...}) = 0 close(3) = 0 rt_sigaction(SIGHUP, {0x1, [], SA_STACK|0x129b3d8}, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_RESTART|SA_RESETHAND|0x22302d0}, 8) = 0 rt_sigaction(SIGINT, {0x1, [], SA_STACK|0x129b3d8}, {SIG_DFL, [TRAP BUS FPE USR1 CHLD CONT TTOU VTALRM IO RTMIN], SA_RESTART|SA_RESETHAND|0x22302d0}, 8) = 0 rt_sigaction(SIGQUIT, {0x1, [], 0}, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_RESTART|SA_RESETHAND|0x22302d0}, 8) = 0 waitpid(20215, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0) = 20215 rt_sigaction(SIGHUP, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 rt_sigaction(SIGINT, {SIG_DFL, [TRAP BUS FPE USR1 CHLD CONT TTOU VTALRM IO RTMIN], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 rt_sigaction(SIGQUIT, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 chdir("/usr/lib/.khostd") = 0 pipe([3, 4]) = 0 pipe([5, 6]) = 0 clone(child_stack=0, flags=CLONE_CHILD_CLEARTID|CLONE_CHILD_SETTID|SIGCHLD, child_tidptr=0) = 20218 close(6) = 0 close(4) = 0 read(5, "", 4) = 0 close(5) = 0 ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd61868) = -1 EINVAL (Invalid argument) _llseek(3, 0, 0xffd61890, SEEK_CUR) = -1 ESPIPE (Illegal seek) read(3, "", 4096) = 0 --- SIGCHLD (Child exited) @ 0 (0) --- close(3) = 0 rt_sigaction(SIGHUP, {0x1, [], SA_RESTORER|SA_STACK|SA_RESTART|SA_INTERRUPT|SA_NODEFER|SA_RESETHAND|0x3d61850, (nil)}, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, 8) = 0 rt_sigaction(SIGINT, {0x1, [], SA_STACK|0x129b3d8}, {SIG_DFL, [HUP INT], SA_NOCLDSTOP|SA_NOCLDWAIT}, 8) = 0 rt_sigaction(SIGQUIT, {0x1, [], 0}, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, 8) = 0 waitpid(20218, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0) = 20218 rt_sigaction(SIGHUP, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 rt_sigaction(SIGINT, {SIG_DFL, [HUP INT], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 rt_sigaction(SIGQUIT, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 chdir("/home/deploy") = 0 stat64("/etc/cron.hourly/hichina", {st_mode=S_IFREG|0755, st_size=711660, ...}) = 0 pipe([3, 4]) = 0 pipe([5, 6]) = 0 clone(child_stack=0, flags=CLONE_CHILD_CLEARTID|CLONE_CHILD_SETTID|SIGCHLD, child_tidptr=0) = 20230 close(6) = 0 close(4) = 0 read(5, "", 4) = 0 close(5) = 0 ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xffd61868) = -1 EINVAL (Invalid argument) _llseek(3, 0, 0xffd61890, SEEK_CUR) = -1 ESPIPE (Illegal seek) read(3, "procps version 3.2.7\n", 4096) = 21 read(3, "", 4096) = 0 --- SIGCHLD (Child exited) @ 0 (0) --- close(3) = 0 rt_sigaction(SIGHUP, {0x1, [], SA_RESTORER|SA_STACK|SA_RESTART|SA_INTERRUPT|SA_NODEFER|SA_RESETHAND|0x3d61850, (nil)}, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, 8) = 0 rt_sigaction(SIGINT, {0x1, [], SA_STACK|0x129b3d8}, {SIG_DFL, [HUP INT], SA_NOCLDSTOP|SA_NOCLDWAIT}, 8) = 0 rt_sigaction(SIGQUIT, {0x1, [], 0}, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, 8) = 0 waitpid(20230, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0) = 20230 rt_sigaction(SIGHUP, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 rt_sigaction(SIGINT, {SIG_DFL, [HUP INT], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 rt_sigaction(SIGQUIT, {SIG_DFL, ~[HUP INT ILL TRAP KILL SEGV ALRM TERM STKFLT CHLD TSTP TTOU RT_1 RT_2 RT_3 RT_6 RT_9 RT_11 RT_14 RT_15 RT_16 RT_17 RT_20 RT_22], SA_NOCLDSTOP|SA_NOCLDWAIT}, NULL, 8) = 0 write(1, "procps version 3.2.7\n", 21procps version 3.2.7 ) = 21 munmap(0xf7af1000, 135168) = 0 munmap(0xf7e70000, 630784) = 0 munmap(0xf7f0a000, 634880) = 0 munmap(0xf7d4e000, 1140104) = 0 exit_group(0) = ? [ Process PID=20214 runs in 32 bit mode. ] Thank you very much.

  Read the article

• C++ assignment operators dynamic arrays

  - by user2905445

  First off i know the multiplying part is wrong but i have some questions about the code. 1. When i am overloading my operator+ i print out the matrix using cout << *this then right after i return *this and when i do a+b on matix a and matix b it doesnt give me the same thing this is very confusing. 2. When i make matrix c down in my main i cant use my default constructor for some reason because when i go to set it = using my assignment operator overloaded function it gives me an error saying "expression must be a modifiable value. although using my constructor that sets the row and column numbers is the same as my default constructor using (0,0). 3. My assignment operator= function uses a copy constructor to make a new matrix using the values on the right hand side of the equal sign and when i print out c it doesn't give me anything Any help would be great this is my hw for a algorithm class which i still need to do the algorithm for the multiplying matrices but i need to solve these issues first and im having a lot of trouble please help. //Programmer: Eric Oudin //Date: 10/21/2013 //Description: Working with matricies #include <iostream> using namespace std; class matrixType { public: friend ostream& operator<<(ostream&, const matrixType&); const matrixType& operator*(const matrixType&); matrixType& operator+(const matrixType&); matrixType& operator-(const matrixType&); const matrixType& operator=(const matrixType&); void fillMatrix(); matrixType(); matrixType(int, int); matrixType(const matrixType&); ~matrixType(); private: int **matrix; int rowSize; int columnSize; }; ostream& operator<< (ostream& osObject, const matrixType& matrix) { osObject << endl; for (int i=0;i<matrix.rowSize;i++) { for (int j=0;j<matrix.columnSize;j++) { osObject << matrix.matrix[i][j] <<", "; } osObject << endl; } return osObject; } const matrixType& matrixType::operator=(const matrixType& matrixRight) { matrixType temp(matrixRight); cout << temp; return temp; } const matrixType& matrixType::operator*(const matrixType& matrixRight) { matrixType temp(rowSize*matrixRight.columnSize, columnSize*matrixRight.rowSize); if(rowSize == matrixRight.columnSize) { for (int i=0;i<rowSize;i++) { for (int j=0;j<columnSize;j++) { temp.matrix[i][j] = matrix[i][j] * matrixRight.matrix[i][j]; } } } else { cout << "Cannot multiply matricies that have different size rows from the others columns." << endl; } return temp; } matrixType& matrixType::operator+(const matrixType& matrixRight) { if(rowSize == matrixRight.rowSize && columnSize == matrixRight.columnSize) { for (int i=0;i<rowSize;i++) { for (int j=0;j<columnSize;j++) { matrix[i][j] += matrixRight.matrix[i][j]; } } } else { cout << "Cannot add matricies that are different sizes." << endl; } cout << *this; return *this; } matrixType& matrixType::operator-(const matrixType& matrixRight) { matrixType temp(rowSize, columnSize); if(rowSize == matrixRight.rowSize && columnSize == matrixRight.columnSize) { for (int i=0;i<rowSize;i++) { for (int j=0;j<columnSize;j++) { matrix[i][j] -= matrixRight.matrix[i][j]; } } } else { cout << "Cannot subtract matricies that are different sizes." << endl; } return *this; } void matrixType::fillMatrix() { for (int i=0;i<rowSize;i++) { for (int j=0;j<columnSize;j++) { cout << "Enter the matix number at (" << i << "," << j << "):"; cin >> matrix[i][j]; } } } matrixType::matrixType() { rowSize=0; columnSize=0; matrix = new int*[rowSize]; for (int i=0; i < rowSize; i++) { matrix[i] = new int[columnSize]; } } matrixType::matrixType(int setRows, int setColumns) { rowSize=setRows; columnSize=setColumns; matrix = new int*[rowSize]; for (int i=0; i < rowSize; i++) { matrix[i] = new int[columnSize]; } } matrixType::matrixType(const matrixType& otherMatrix) { rowSize=otherMatrix.rowSize; columnSize=otherMatrix.columnSize; matrix = new int*[rowSize]; for (int i = 0; i < rowSize; i++) { for (int j = 0; j < columnSize; j++) { matrix[i]=new int[columnSize]; matrix[i][j]=otherMatrix.matrix[i][j]; } } } matrixType::~matrixType() { delete [] matrix; } int main() { matrixType a(2,2); matrixType b(2,2); matrixType c(0,0); cout << "fill matrix a:"<< endl;; a.fillMatrix(); cout << "fill matrix b:"<< endl;; b.fillMatrix(); cout << a; cout << b; c = a+b; cout <<"matrix a + matrix b =" << c; system("PAUSE"); return 0; }

  Read the article

• LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

  - by Andy Shinn

  I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 mirrors. The problem I am running in to is that there are duplicate slots for the 2 chassis (the slots list twice and only go from 0 to 27). All the drives also show the same enclosure ID (ID 36). However, MegaCLI -encinfo lists the 2 enclosures correctly (ID 36 and ID 65). My question is, why would this happen? Is there an option I am missing to use 2 enclosures effectively? This is blocking me rebuilding a drive that failed in slot 11 since I can only specify enclosure and slot as parameters to replace a drive. When I do this, it picks the wrong slot 11 (device ID 46 instead of device ID 19). Adapter #1 is the LSI 9285-8e, adapter #0 (which I removed due to space limitations) is the onboard LSI. Adapter information: Adapter #1 ============================================================================== Versions ================ Product Name : LSI MegaRAID SAS 9285-8e Serial No : SV12704804 FW Package Build: 23.1.1-0004 Mfg. Data ================ Mfg. Date : 06/30/11 Rework Date : 00/00/00 Revision No : 00A Battery FRU : N/A Image Versions in Flash: ================ BIOS Version : 5.25.00_4.11.05.00_0x05040000 WebBIOS Version : 6.1-20-e_20-Rel Preboot CLI Version: 05.01-04:#%00001 FW Version : 3.140.15-1320 NVDATA Version : 2.1106.03-0051 Boot Block Version : 2.04.00.00-0001 BOOT Version : 06.253.57.219 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 005b SubVendorId : 1000 SubDeviceId : 9285 Host Interface : PCIE ChipRevision : B0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5003048000ee8e7f 1 5003048000ee8a7f 2 0000000000000000 3 0000000000000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 500605b0038f9210 BBU : Present Alarm : Present NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 1024MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Present Temperature sensor for controller : Absent ROC temperature : 70 degree Celcius Settings ================ Current Time : 18:24:36 3/13, 2012 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : Disabled Cluster Mode : Disabled Alarm : Enabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Enabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 10 Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Mix of SAS/SATA of HDD type in VD Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 60 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 16 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 887 MB Device Present ================ Virtual Drives : 28 Degraded : 0 Offline : 0 Physical Devices : 59 Disks : 56 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : No Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : No Support Boot Time PFK Change : Yes Disable Online PFK Change : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : Yes Block SSD Write Disk Cache Change: Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : No Power Savings : Yes Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Enable Spin Down of UnConfigured Drives : Yes Disable Spin Down of hot spares : No Spin Down time : 30 T10 Power State : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : Yes Coercion Mode : None ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : Yes Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : Yes Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : Yes Disable Puncturing : No Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : Yes LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : Don't Auto spin down Configured Drives Max power savings option is not allowed for LDs. Only T10 power conditions are to be used. Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : No BreakMirror RAID Support : No Disable Join Mirror : No Enable Shield State : Yes Time taken to detect CME : 60s Exit Code: 0x00 Enclosure information: # /opt/MegaRAID/MegaCli/MegaCli64 -encinfo -a1 Number of enclosures on adapter 1 -- 3 Enclosure 0: Device ID : 36 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port B Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 65 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11820 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 48 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 1: Device ID : 65 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port A Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 36 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11760 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 47 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 2: Device ID : 252 Number of Slots : 8 Number of Power Supplies : 0 Number of Fans : 0 Number of Temperature Sensors : 0 Number of Alarms : 0 Number of SIM Modules : 1 Number of Physical Drives : 0 Status : Normal Position : 1 Connector Name : Unavailable Enclosure type : SGPIO Failed in first Inquiry commnad FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : Unavailable Inquiry data : Vendor Identification : LSI Product Identification : SGPIO Product Revision Level : N/A Vendor Specific : Exit Code: 0x00 Now, notice that each slot 11 device shows an enclosure ID of 36, I think this is where the discrepancy happens. One should be 36. But the other should be on enclosure 65. Drives in slot 11: Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 5, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 48 WWN: Sequence Number: 11 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : YES Device Firmware Level: A5C0 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8a53 Connected Port Number: 1(path0) Inquiry Data: MJ1311YNG6YYXAHitachi HDS5C3030ALA630 MEAOA5C0 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 19, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 19 WWN: Sequence Number: 4 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : NO Device Firmware Level: A580 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8e53 Connected Port Number: 0(path0) Inquiry Data: MJ1313YNG1VA5CHitachi HDS5C3030ALA630 MEAOA580 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Update 06/28/12: I finally have some new information about (what we think) the root cause of this problem so I thought I would share. After getting in contact with a very knowledgeable Supermicro tech, they provided us with a tool called Xflash (doesn't appear to be readily available on their FTP). When we gathered some information using this utility, my colleague found something very strange: root@mogile2 test]# ./xflash.dat -i get avail Initializing Interface. Expander: SAS2X36 (SAS2x36) 1) SAS2X36 (SAS2x36) (50030480:00EE917F) (0.0.0.0) 2) SAS2X36 (SAS2x36) (50030480:00E9D67F) (0.0.0.0) 3) SAS2X36 (SAS2x36) (50030480:0112D97F) (0.0.0.0) This lists the connected enclosures. You see the 3 connected (we have since added a 3rd and a 4th which is not yet showing up) with their respective SAS address / WWN (50030480:00EE917F). Now we can use this address to get information on the individual enclosures: [root@mogile2 test]# ./xflash.dat -i 5003048000EE917F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00EE917F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 5003048000E9D67F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00E9D67F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 500304800112D97F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:0112D97F Enclosure Logical Id: 50030480:0112D97F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 Did you catch it? The first 2 enclosures logical ID is partially masked out where the 3rd one (which has a correct unique enclosure ID) is not. We pointed this out to Supermicro and were able to confirm that this address is supposed to be set during manufacturing and there was a problem with a certain batch of these enclosures where the logical ID was not set. We believe that the RAID controller is determining the ID based on the logical ID and since our first 2 enclosures have the same logical ID, they get the same enclosure ID. We also confirmed that 0000007F is the default which comes from LSI as an ID. The next pointer that helps confirm this could be a manufacturing problem with a run of JBODs is the fact that all 6 of the enclosures that have this problem begin with 00E. I believe that between 00E8 and 00EE Supermicro forgot to program the logical IDs correctly and neglected to recall or fix the problem post production. Fortunately for us, there is a tool to manage the WWN and logical ID of the devices from Supermicro: ftp://ftp.supermicro.com/utility/ExpanderXtools_Lite/. Our next step is to schedule a shutdown of these JBODs (after data migration) and reprogram the logical ID and see if it solves the problem. Update 06/28/12 #2: I just discovered this FAQ at Supermicro while Google searching for "lsi 0000007f": http://www.supermicro.com/support/faqs/faq.cfm?faq=11805. I still don't understand why, in the last several times we contacted Supermicro, they would have never directed us to this article :\

  Read the article

• Why is my router not routing?

  - by dwj

  Starting a week and half ago my router stopped working with my cable modem. I went to sleep with it working and woke up with it not. I swapped in another router and am still having issues; I was gone for 10 days so now I'm back to trying to figure it out. While I was gone I left everything (cable modem, router, and computer) powered off. My setup: Comcast Ambit cable modem (from Comcast) Netgear WGR614 v4 router -- replaced with Linksys WRT54GS v1.1 Windows XP SP3 other computers, all currently unplugged The modem is using the firmware (ver 2.105.2001) provided by Comcast; hardware version 1.3 The Linksys router is using FW ver 4.71.4 (latest for this release of HW), factory defaults I am only using the wired connections; no wireless. I have swapped out all of the cat5 cable. If I plug my computer directly into the cable modem, I can ping by name or number. Everything works perfectly. If I plug my computer into the router and the router into the modem, I cannot access anything outside of my local network. This is the exact setup I've used for the past 5 years; there were no changes in the past year. Now here's the interesting part: I can log into the Linksys router and get status information from it; everything appears good. Using the Diagnostics, I can run ping and traceroute to any site on the internet. These work perfectly. From my computer, I can ping the router and the modem. However, I cannot ping anything on the internet by with name or number. If I plug in another computer, I can ping it successfully. I've included two transcripts below that show these two attempts. Addresses, DNS, gateways, etc. look good. I cannot access the internet through either router. I am at a loss here. Suggestions? Help! Computer to Router to Cable Modem C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:21:55 PM Lease Expires . . . . . . . . . . : Tuesday, March 23, 2010 10:21:55 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Ping request could not find host google.com. Please check the name and try again . C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\ Computer to Cable Modem Directly C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 DHCP Server . . . . . . . . . . . : 68.87.76.10 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:18:50 PM Lease Expires . . . . . . . . . . : Monday, March 22, 2010 11:12:31 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Pinging google.com [74.125.19.99] with 32 bytes of data: Reply from 74.125.19.99: bytes=32 time=20ms TTL=55 Reply from 74.125.19.99: bytes=32 time=17ms TTL=55 Reply from 74.125.19.99: bytes=32 time=28ms TTL=55 Reply from 74.125.19.99: bytes=32 time=18ms TTL=55 Ping statistics for 74.125.19.99: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 17ms, Maximum = 28ms, Average = 20ms C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=17ms TTL=55 Reply from 74.125.19.104: bytes=32 time=16ms TTL=55 Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 16ms, Maximum = 18ms, Average = 17ms C:\

  Read the article

< Previous Page | 12 13 14 15 16 17  | Next Page >