Search Results

Search found 1264 results on 51 pages for 'mini displayport'.

Page 16/51 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

• Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

  - by Joe Hopfgartner

  I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

  Read the article

• Robotic Arm &ndash; Hardware

  - by Szymon Kobalczyk

  This is first in series of articles about project I've been building  in my spare time since last Summer. Actually it all began when I was researching a topic of modeling human motion kinematics in order to create gesture recognition library for Kinect. This ties heavily into motion theory of robotic manipulators so I also glanced at some designs of robotic arms. Somehow I stumbled upon this cool looking open source robotic arm: It was featured on Thingiverse and published by user jjshortcut (Jan-Jaap). Since for some time I got hooked on toying with microcontrollers, robots and other electronics, I decided to give it a try and build it myself. In this post I will describe the hardware build of the arm and in later posts I will be writing about the software to control it. Another reason to build the arm myself was the cost factor. Even small commercial robotic arms are quite expensive – products from Lynxmotion and Dagu look great but both cost around USD $300 (actually there is one cheap arm available but it looks more like a toy to me). In comparison this design is quite cheap. It uses seven hobby grade servos and even the cheapest ones should work fine. The structure is build from a set of laser cut parts connected with few metal spacers (15mm and 47mm) and lots of M3 screws. Other than that you’d only need a microcontroller board to drive the servos. So in total it comes a lot cheaper to build it yourself than buy an of the shelf robotic arm. Oh, and if you don’t like this one there are few more robotic arm projects at Thingiverse (including one by oomlout). Laser cut parts Some time ago I’ve build another robot using laser cut parts so I knew the process already. You can grab the design files in both DXF and EPS format from Thingiverse, and there are also 3D models of each part in STL. Actually the design is split into a second project for the mini servo gripper (there is also a standard servo version available but it won’t fit this arm).  I wanted to make some small adjustments, layout, and add measurements to the parts before sending it for cutting. I’ve looked at some free 2D CAD programs, and finally did all this work using QCad 3 Beta with worked great for me (I also tried LibreCAD but it didn’t work that well). All parts are cut from 4 mm thick material. Because I was worried that acrylic is too fragile and might break, I also ordered another set cut from plywood. In the end I build it from plywood because it was easier to glue (I was told acrylic requires a special glue). Btw. I found a great laser cutter service in Kraków and highly recommend it (www.ebbox.com.pl). It cost me only USD $26 for both sets ($16 acrylic + $10 plywood). Metal parts I bought all the M3 screws and nuts at local hardware store. Make sure to look for nylon lock (nyloc) nuts for the gripper because otherwise it unscrews and comes apart quickly. I couldn’t find local store with metal spacers and had to order them online (you’d need 11 x 47mm and 3 x 15mm). I think I paid less than USD $10 for all metal parts. Servos This arm uses five standards size servos to drive the arm itself, and two micro servos are used on the gripper. Author of the project used Modelcraft RS-2 Servo and Modelcraft ES-05 HT Servo. I had two Futaba S3001 servos laying around, and ordered additional TowerPro SG-5010 standard size servos and TowerPro SG90 micro servos. However it turned out that the SG90 won’t fit in the gripper so I had to replace it with a slightly smaller E-Sky EK2-0508 micro servo. Later it also turned out that Futaba servos make some strange noise while working so I swapped one with TowerPro SG-5010 which has higher torque (8kg / cm). I’ve also bought three servo extension cables. All servos cost me USD $45. Assembly The build process is not difficult but you need to think carefully about order of assembling it. You can do the base and upper arm first. Because two servos in the base are close together you need to put first with one piece of lower arm already connected before you put the second servo. Then you connect the upper arm and finally put the second piece of lower arm to hold it together. Gripper and base require some gluing so think it through too. Make sure to look closely at all the photos on Thingiverse (also other people copies) and read additional posts on jjshortcust’s blog: My mini servo grippers and completed robotic arm  Multiply the robotic arm and electronics Here is also Rob’s copy cut from aluminum My assembled arm looks like this – I think it turned out really nice: Servo controller board The last piece of hardware I needed was an electronic board that would take command from PC and drive all seven servos. I could probably use Arduino for this task, and in fact there are several Arduino servo shields available (for example from Adafruit or Renbotics).  However one problem is that most support only up to six servos, and second that their accuracy is limited by Arduino’s timer frequency. So instead I looked for dedicated servo controller and found a series of Maestro boards from Pololu. I picked the Pololu Mini Maestro 12-Channel USB Servo Controller. It has many nice features including native USB connection, high resolution pulses (0.25µs) with no jitter, built-in speed and acceleration control, and even scripting capability. Another cool feature is that besides servo control, each channel can be configured as either general input or output. So far I’m using seven channels so I still have five available to connect some sensors (for example distance sensor mounted on gripper might be useful). And last but important factor was that they have SDK in .NET – what more I could wish for! The board itself is very small – half of the size of Tic-Tac box. I picked one for about USD $35 in this store. Perhaps another good alternative would be the Phidgets Advanced Servo 8-Motor – but it is significantly more expensive at USD $87.30. The Maestro Controller Driver and Software package includes Maestro Control Center program with lets you immediately configure the board. For each servo I first figured out their move range and set the min/max limits. I played with setting the speed an acceleration values as well. Big issue for me was that there are two servos that control position of lower arm (shoulder joint), and both have to be moved at the same time. This is where the scripting feature of Pololu board turned out very helpful. I wrote a script that synchronizes position of second servo with first one – so now I only need to move one servo and other will follow automatically. This turned out tricky because I couldn’t find simple offset mapping of the move range for each servo – I had to divide it into several sub-ranges and map each individually. The scripting language is bit assembler-like but gets the job done. And there is even a runtime debugging and stack view available. Altogether I’m very happy with the Pololu Mini Maestro Servo Controller, and with this final piece I completed the build and was able to move my arm from the Meastro Control program.   The total cost of my robotic arm was: $10 laser cut parts $10 metal parts $45 servos $35 servo controller ----------------------- $100 total So here you have all the information about the hardware. In next post I’ll start talking about the software that I wrote in Microsoft Robotics Developer Studio 4. Stay tuned!

  Read the article

• How to implement RSA-CBC?(I have uploaded the request document)

  - by tq0fqeu

  I don't konw more about cipher, I just want to implement RSA-CBC which maybe mean that the result of RSA encrypt in CBC mode, and I have implemented RSA. any code languages will be ok, java will be appreciated thx I copy the request as follow(maybe has spelling wrong), but that's French I don't konw that: Pr´esentation du mini-projet Le but du mini-projet est d’impl´ementer une version ´el´ementaire du chi?rement d’un bloc par RSA et d’inclure cette primitive dans un systeme de chi?rement par bloc avec chaˆinage de blocs et IV (Initial Vector ) al´eatoire. Dans ce systeme, un texte clair (`a chi?rer) est d´ecompos´e en blocs de taille t (?x´ee par l’utilisa- teur), chaque bloc (clair) est chi?r´e par RSA en un bloc crypt´e de mˆeme taille, puis le cryptogramme associ´e au texte clair initial est obtenu en chaˆinant les blocs crypt´es par la m´ethode CBC (cipher- block chaining) d´ecrite dans le cours (voir poly “Block Ciphers”) Votre programme devra demander a l’utilisateur la taille t, puis, apres g´en´eration des cl´es publique et priv´ee, lui proposer de chi?rer ou d´echi?rer un (court) ?chier ASCII. Il est indispensable que votre programme soit au moins capable de traiter le cas (tres peu r´ealiste du point de vue de la s´ecurit´e) t = 32. Pour les traiter des blocs plus grands, il vous faudra impl´ementer des routines d’arithm´etique multi-pr´ecision ; pour cela, je vous conseille de faire appela des bibliotheques libres comme GMP (GNU Multiprecision Library). Pour la g´en´eration al´eatoire des nombres premiers p et q, vous pouvez ´egalement faire appela des bibliotheques sp´ecialis´ees,a condition de me donner toutes les pr´ecisions n´ecessaires. Vous devez m’envoyer (avant une date qui reste a ?xer)a mon adresse ´electronique ([email protected]) un courriel (sujet : [MI1-crypto] : devoir, corps du message : les noms des ´etudiants ayant travaill´e sur le mini-projet) auquel sera attach´e un dossier compress´e regroupant vos sources C ou Java comment´ees, votre programme ex´ecutable, et un ?chier texte ou PDF donnant toutes les pr´ecisions sur les biblioth`eques utilis´ees, vos choix algorithmiques et d’impl´ementation, et les raisons de ces choix (complexit´e algorithmique, robus- tesse, facilit´e d’impl´ementation, etc.). Vous pouvez travailler en binˆome ou en trinˆome, mais je serai nettement plus exigeant avec les trinˆomes I have uploaded the request at http://uploading.com/files/22emmm6b/enonce_projet.pdf/ thx

  Read the article

• Is there any way to combine transparency and "ajax usability" with HTML templates

  - by Sam

  I'm using HTML_Template_Flexy in PHP but the question should apply to any language or template library. I am outputting a list of relatively complex objects. In the beginning I just iterated over a list of the objects and called a toHtml method on them. When I was about to have my layout designer look over the template I noticed that it was too opaque and that he would have ended up looking through and/or editing many additional php source files to see what really gets generated by the toHtml method. So I extracted most of the HTML strings in the php classes up to the template which made for one clear file where you can see the whole page structure at once. However this causes problems when you want to add an object to the list using javascript. Then I have to keep the old toHtml method and maintain both the main template and the html strings at the same time, so I can output just the HTML for a new object that should be added to the page. So I'm back to the idea of using smaller templates for the objects that make up the page, but I was wondering if there was some easy way of having my cake and eating it too by having one template that shows the whole page but also the mini-templates for smaller objects on the page. Edit: Yes, updating the page is not a problem at all. My concern is with having both maintainability and transparency of the template files. If I have one single template for the whole page, then I must maintain mini-templates of the objects that are shown on the page. If I just have the mini-templates and include them from the higher-level template it becomes more difficult to look at the top-level html and imagine what the end result will look like.

  Read the article

• building a gl3 app under cygwin

  - by user445264

  i've got a small opengl 3.2 app that i've been developing on linux using the standard gnu tools (gmake/gcc). the code seems pretty portable--i had no problems running it on osx until i started using gl3 features that the mac mini gl drivers don't seem to support. i've got a bootcamp partition with windows xp on the same mini, and i'd like to run my app there if possible. the windows drivers definitely support gl 3.2, but i'm having trouble linking. this seems like a really common issue, but i haven't found any answers online that address using opengl 1.2 under cygwin. i'm using glew-1.5.5 and linking like so: g++ -o glToy *.o -L/cygdrive/c/Program\ Files/glew-1.5.5/lib -lglew32 -lglut32 -lglu32 -lopengl32 but i get a whole lot of this sort of output: Program.o:/home/Jacob/glToy/Program.cpp:134: undefined reference to `__imp____glewUseProgram' Program.o:/home/Jacob/glToy/Program.cpp:235: undefined reference to `__imp____glewActiveTexture' Program.o:/home/Jacob/glToy/Program.cpp:73: undefined reference to `__imp____glewGetShaderiv' ... any ideas what i'm doing wrong? or perhaps this isn't a workable setup? other ideas for getting this going on the mac mini (2009 version)? thanks!

  Read the article

• How to check if a position inside a std string exists ?? (c++)

  - by yox

  Hello, i have a long string variable and i want to search in it for specific words and limit text according to thoses words. Say i have the following text : "This amazing new wearable audio solution features a working speaker embedded into the front of the shirt and can play music or sound effects appropriate for any situation. It's just like starring in your own movie" and the words : "solution" , "movie". I want to substract from the big string (like google in results page): "...new wearable audio solution features a working speaker embedded..." and "...just like starring in your own movie" for that i'm using the code : for (std::vector<string>::iterator it = words.begin(); it != words.end(); ++it) { int loc1 = (int)desc.find( *it, 0 ); if( loc1 != string::npos ) { while(desc.at(loc1-i) && i<=80){ i++; from=loc1-i; if(i==80) fromdots=true; } i=0; while(desc.at(loc1+(int)(*it).size()+i) && i<=80){ i++; to=loc1+(int)(*it).size()+i; if(i==80) todots=true; } for(int i=from;i<=to;i++){ if(fromdots) mini+="..."; mini+=desc.at(i); if(todots) mini+="..."; } } but desc.at(loc1-i) causes OutOfRange exception... I don't know how to check if that position exists without causing an exception ! Help please!

  Read the article

• Issues with simple jQuery image gallery with Colorbox plugin

  - by Chris

  I'm putting together an image gallery for an ecommerce site and wanting to use colorbox to launch larger images. My problem is that image launched in colorbox stays as the first one launched and should reflect the image shown as img#bigpic - the link to the image does appear to be updating correctly. Here's the jQuery I have: $(document).ready(function(){ $("#largeimage").colorbox(); imageSwapper(".thumbnails a"); function imageSwapper(link) { $(link).click(function(){ $("#bigpic").attr("src", this.href); $("#largeimage").attr("href", this.rel); return false; }); }; $("#largeimage").bind('mouseenter mouseleave', function(event) { $("#largeimage span").toggleClass('showspan'); }); }); ...and the HTML <a href="_images/products/large/bpn0001_1.jpg" id="largeimage"><span></span><img src="_images/products/bpn0001_1.jpg" id="bigpic" /></a> <div class="thumbnails"> <ul> <li><a href="_images/products/bpn0001_1.jpg" rel="_images/products/large/bpn0001_1.jpg"><img src="_images/products/mini/bpn0001_1.jpg" /></a></li> <li><a href="_images/products/bpn0001_2.jpg" rel="_images/products/large/bpn0001_2.jpg"><img src="_images/products/mini/bpn0001_2.jpg" /></a></li> <li><a href="_images/products/bpn0001_3.jpg" rel="_images/products/large/bpn0001_3.jpg"><img src="_images/products/mini/bpn0001_3.jpg" /></a></li> </ul> </div> Any help would be much appreciated!

  Read the article

• Best triple head display setup

  - by dgel

  I'm currently running Ubuntu 12.04 with a darn good triple head display setup. I've got a VisionTek 900530 Radeon HD 5450 512MB DDR3 PCI Express video card that has two DVI outputs and one Mini DisplayPort that I have connected to a HDMI adapter. I'm running three identical Asus 1920x1080 monitors that each have a DVI, VGA, and HDMI input. I'm using the xorg-edgers ppa, so I'm using the open source radeon driver version 6.99.99. I tried using the ATI binary fglrx driver, but I wasn't able to get the three monitors working properly- the monitor connected via HDMI / DisplayPort wouldn't run at full resolution. The setup is almost perfect: Compiz runs fine and is quite snappy. I'm not able to use that great compiz feature where you can drag a window to the side of a display and it will half maximize. I occasionally experience display corruption weirdness with Unity and need to restart it. When I use a dropdown menu in LibreOffice it often pops the menu down in another window. For example, if I'm using the center monitor and click the Insert menu, the menu pulls down on the monitor to my right, forcing me to chase it. If I chase down the menu and choose Manual Break, the dialog appears over on my left monitor. This absurdity is mildly entertaining but has lost its novelty. I've decided to build a new system and have spared no expense- latest i7 processor, SSD, etc. I really like the performance of the Nvidia binary drivers, so I put two ZOTAC ZT-40707-10L GeForce GT 440 in the system, figuring I'd have four DVI outputs and an awesome triple (or even eventually quad) head setup. Unfortunately it appears that I didn't do sufficient research before my purchase. It seems that Nvidia TwinView only supports two monitors on one card (I guess that's why they call it TwinView...). I messed around with running two X servers, but I really don't want that- being able to drag windows to any monitor is critical. It doesn't sound like Xinerama is an option because from what I understand it simply doesn't support Compiz. I've seen a BaseMosaic option that can be used with the Nvidia drivers that appears to support an almost unlimited number of heads- unfortunately me cheap little cards don't support it. I'm also not sure whether you'll still have all nice maximizing and snapping that TwinView provides, or whether Ubuntu will only see it as one massive display. I put my old trusty ATI card into my new system and installed 12.10. I'm using the opensource radeon drivers again because even in 12.10 I can't get the fglrx binary drivers to do triple head. Unfortunately, even with an unbelievably powerful system the experience is extremely sluggish (much more so than my experience in 12.04). The menu scattering problem appears to be fixed, but I get a lot of nasty Unity display corruption. So finally, my question is this: What hardware / drivers should I use? I'm willing to buy (almost) any video card(s). I have two PCI-Express 3.0 slots on my motherboard (which has an integrated Intel HD card). I'm willing to use ATI or Nvidia cards and willing to run Ubuntu 12.04.1 or 12.10. I'm not a gamer, but do want beautiful and snappy Compiz effects. Does anyone out there have the perfect triple head setup in 12.04 or 12.10? What hardware / drivers are you using? I have those two Nvidia cards but will probably be returning them unless someone knows a way to use them together for a triple head setup. Since I'm having pretty good luck with a single ATI card providing three displays, should I just buy a beefier one with the hopes that it will fix the horrible sluggishness I'm experiencing in 12.10?

  Read the article

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• MacBook Pro + OSX Lion + Samsung SA550 HDMI not playing nicely

  - by rabbid

  I bought a Samsung SA550 monitor as a second monitor for my 2009 MacBook Pro that is running OSX 10.7 Lion. The monitor has 2 outputs, VGA and HDMI. If I connect using VGA everything is fine. If I connect using HDMI-DVI cable, and DVI-to-mini display converter I get static and flickering: The DVI-to-mini display converter that I use: I have used this converter with a different monitor that had a DVI output port a while ago, so at least it used to work once upon a time. I am not sure if this problem is because of that converter or not. I have never used a monitor with an HDMI output before. Appreciate your help. Thank you!

  Read the article

• How can I switch between the HDMI and DVI outputs of my graphics card?

  - by Owen Melbourne

  I've got an Nvidia GTX 560ti card which currently I've got my 2 monitors hooked up to using the 2 DVI ports. However its got a mini-HDMI port which I've plugged a HDMI cable in (with mini adapter) and lead it into my TV which is across the room. I'm hoping to be able to toggle between the HDMI output and the DVI outputs, however I'm not sure how I'd go about this, Could somebody please point me in the right direction, I'm not really worried about having all 3 on at the same time so that isn't a problem, but if its possible then I'll do that.

  Read the article

• Audigy 2 Coaxial to Coaxial/Optical connection possible?

  - by Chris

  Hello, The original question is deleted, and asked again below with accurate information. Edit: Excuse me for my ignorance, my friend has a Logitech Z-5500 set. I thought after comparing those systems on Google images that he had the Z-680, but he hasn't. This set has a single Digital coaxial for DVD or CD players or PC sound cards (requires coaxial cable, sold separately) cable. This single cable was connected to the orange tulip connector (SPDIF coaxial out) on the backside of his onboard HP Elite m9070, this connector is broken. How can I use the digital out with a single cable coaxial cable on the Audigy2 (see image below) (I have the following converters for my disposal, can I use one of these? 3.5 mm male - coax optical mini optical male - toslink optical female 2 x toslink optical female, toslink coupler, optical audio extension note: Is it possible to connect a toslink cable with an mini optical male - toslink converter on the digital out of the Audigy 2? (see image below)

  Read the article

• ScreenShare: command line and observe only.

  - by Shyam

  Hi, I have a wide TV screen that is attached to a Mac Mini. I am able to use this screen as a second screen using an application like ScreenRecycler. However, Sometimes I want to demonstrate what I am doing on my box on this TV screen. As this TV is attached to a Mac Mini, I want to have a screen sharing done reversed. As I know screen share can be done in observe mode and full screen, this would be more than sufficient. Because it would be pretty useless to run it continuously, I want it on demand. For this, I want to use SSH. So the only thing I would like to know is, how do I start screen sharing in from a Terminal Session. On Windows, I could start an application by using "start notepad.exe", I am looking for something similar. Eventually, I want to make this work on other boxes too. Thanks for your help!

  Read the article

• 10 gigabit or 1 gigabit switch

  - by Guntis

  We are planning to move mysql to dedicated box. At this moment we have web servers and mysql is running on each. Question is: cheaper is to buy 10G switch and put 10G network card into mysql server. Or buy normal gigabit switch and connect mysql box to switch with multiple network cables. In 1G scenario then we give each web server different mysql IP address. I don't think, that mysql box with one 1G link is enough to to satisfy multiple web box mysql traffic. At this moment we have 3 servers witch are running mysql/web. Plan is to add fourth server for mysql only. Thanks. Edit: if we buy 1G switch with mini-GBIC ports. Can we put in mini-GBIC 10G connectors and then connect mysql box to that port?

  Read the article

• Isass.exe Application error

  - by shelbang

  I own a hp mini. It has come up with a blue screen and says: The Application failed to intialize properly (0xc0000005). Click on OK to terminate the application. i click on it twice but it stayed on the blank blue screen. i have tryed going on the safe mode thingy.. and pressing F9 and F10 and F8 but none of the above work. Considering its a HP mini- it doesnt have a cd rom compartment!?!? pleasee help !! i cant live without my computer! ): - ps using sisters computer atm :S shhh

  Read the article

• Choosing A Power Supply [closed]

  - by Geeks On Hugs

  Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

  Read the article

• Error when starting squid

  - by Gatura

  i am getting this error when i am starting up squid, it is running on a mac mini cache_cf.cc(346) squid.conf:4871 unrecognized: 'https_port'

  Read the article

• What is the right way to use Internet Sharing in OS X?

  - by Bob King

  For a while now I've been using the Wireless in my Mac Mini as a seperate WiFi access point because my main router doesn't quite cover my whole house. There is a dedicated CAT 5E line down to the Mini, which has a static IP address. I've turned Internet Sharing on, using Airport/WiFi but it seems my options for security are limited. Can I do WPA2? Also, it seems like my iPhone only connects 25% of the time, and the rest of the time it claims I've given a bad password. I've tried "Forget this network" repeatedly.

  Read the article

• Inbound connections using Internet Connection Sharing in Apple/Mac/Leopard

  - by tlianza

  I have a Mac mini which I'm using to give some other devices wireless access, by sharing it's Airport connection with the local ethernet, and that is plugged into a switch. All devices can get online no problem. (See how: http://www.macosxhints.com/article.php?story=20041112101646643 and http://www.macosxhints.com/article.php?story=20071223001432304 ) The issue is that I need to be able to connect in to these machines as well (at least, for the Slingbox to work). All the devices have 192.168.2.* addresses, and the rest of my local network is on 192.168.1.*. I tried setting a static route so that the 192.168.2.* addresses would use a gateway of 192.168.1.50 (my mac mini's address) but that didn't seem to help. Does anyone know if what I'm trying to do is possible? I admit I'm not certain what Internet Connection sharing is really doing under the hood... perhaps it just does basic nat, and doesn't do the type of routing I'm looking for. If so, anyone know if this is possible?

  Read the article

• Changing keyboard layout for login screen on Mac OS X

  - by R.A

  I have a Mac Mini with Mac OS X Lion. Basically I am a developer and practiced coding with DVORAK keyboards. So I changed my keyboard layout to DVORAK and I'm working with it. I'm using the admin user on my Mac Mini. When I restart my computer, during login, the layout is changed to QWERTY and it's hard to type the password. It happens only for the admin user though. If I create the another user and set the layout as DVORAK and restart, that user has the DVORAK keyboard for login. Note: I have a QWERTY keyboard, I'm only changing the layout in the keyboard preferences. So, to summarize, how can I get the DVORAK keyboard layout for the admin login as well?

  Read the article

• how to create a simple radio station [on hold]

  - by John

  I've been digging around for ages but not getting very far so any links or tips would be massively appreciated. I want to create a central "radio station" in my home to stream one playlist to any computers pointing their browser to the ip within my internal network. I have an old mini slave mac mini running ubuntu and was originally thinking I could get php and apache to handle this but then quickly realised that of course, php will serve out streaming independently per connection ie no radio station. Are there any servers already built for this sort of behaviour? is shoutcast one of the only versions Thanks, John

  Read the article

• Dynamic to static internal IP address (Snow Leopard server)

  - by bac

  I purchased a new Mac mini server, since my old iMac, which was a server pretty much died. My problem is this. How do I change my internal IP address for my mac mini server to a static address, like 192.168.0.2? Before you guys harp on me, my old server was running Ubuntu Hardy and I only had to map the IP address in the router, which would automatically assign the reserved address through DHCP. Now, I know things are different between the two, but my problem is that the mac is not accepting the assigned IP address or the router just is not assigning. However, every time I have manually changed it on the Mac to an address of my choice, it takes the computer off the Internet. My router is a NetGear WTG624 v2, I believe. I need this to work, so I can utilize Dynamic DNS.

  Read the article

• Viewsonic VG2427wm detected max resolution too low

  - by Hassan

  So I have a Viewsonic VG2427wm, which supports max resolution of 1920x1080 and I had it working at this resolution from both windows and linux PCs. Now, I need to connect it to my Dell XPS17 (L702x), which has only DP mini and HDMI, so I'm trying to connect this monitor via HDMI-to-DVI adapter (doesn't work at all) and via DP-mini-to-DVI adapter. The later works, but is limiting my max resolution to 1680x1050. Using same two adapters to connect my dell monitor works fine, so I don't suspect any of the adapters to be faulty. The driver is the latest viewsonic driver (although it's been last updated 3 years back). Any ideas, how I can force it to display it's correct native resolution?

  Read the article

• How can I password-protect a Mac shared folder on a Windows workgroup?

  - by Phillip Oldham

  We have a Mac-mini running 10.5.8 which already acts as a fileserver for our simple Windows (mixed XP/Vista) workgroup. The Mac-mini is on the same workgroup and the files are shared via SMB, FTP, and AFP. Basic file-sharing is working, and has been for some time. We'd now like to add an additional directory/share which can be secured by a password so that only a small number on the network have access. Is this possible? I've already tried creating the additional folder on the mac system, adding it to the shared folders, and limiting it to a specific "shared user", however it's not possible to log-in from an XP machine. Adding a sub-directory to the currently working share and giving limiting it's access to the shared user doesn't work either.

  Read the article

• How can I password-protect a Mac shared folder on a Windows workgroup?

  - by Phillip Oldham

  We have a Mac-mini running 10.5.8 which already acts as a fileserver for our simple Windows (mixed XP/Vista) workgroup. The Mac-mini is on the same workgroup and the files are shared via SMB, FTP, and AFP. Basic file-sharing is working, and has been for some time. We'd now like to add an additional directory/share which can be secured by a password so that only a small number on the network have access. Is this possible? I've already tried creating the additional folder on the mac system, adding it to the shared folders, and limiting it to a specific "shared user", however it's not possible to log-in from an XP machine. Adding a sub-directory to the currently working share and giving limiting it's access to the shared user doesn't work either.

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >