Search Results

Search found 2193 results on 88 pages for 'multichannel vpn'.

Page 16/88 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

• VPN to Buffalo WHR-HP-G300N produces a Connection Error 807

  - by Darius

  My friend has modem/router from Clear and I have sent him Buffalo router to put it between his Clear device and the Network. I walked him thru establishing VPN in DD-WRT but when I try to VPN I get a VPN Connection Error 807. I am out of ideas how to solve this. Any suggestion? Clear Modem WAN: xx.xx.xx.xx Clearn Modem NAT's to: 192.168.15.XXX Clear Modem DHCP: 192.168.15.2 - 192.168.15.2 (range is limited to that of ONE ip address) Clear Modem DMZ: 192.168.15.2 the LAN of the clear modem is 192.168.15.XXX The DD-WRT IP: 192.168.4.1 Port FWD: 1723 to 192.168.4.1 PPTP server listens on 192.168.4.1 Where is the problem with this setup?

  Read the article

• VPN server to access Samba4

  - by VisionIncision

  On my network I have an Ubuntu 12.04 server running Samba4, my domain is fully configured and functional. Now, I would like to enable VPN access over the internet, and have another box to do so. I have been searching on the internet for guides and information etc, but have not been successful. I have however found this guide http://www.howtogeek.com/51237/setting-up-a-vpn-pptp-server-on-debian/ but was wondering if I could adapt it somehow to enable access to my DC services. EDIT: I would need to authenticate my VPN server with my DC, if that is possible of course. Any insight would be wonderful. Regards, Jack Hunt

  Read the article

• Weird routing problems with VPN

  - by Borek

  In our VPN setup I have to add a route to my routing table like this: route add 1.2.3.0 mask 255.255.255.0 172.16.1.1 -p Our internal addresses 1.2.3.x then use 172.16.1.1 as their gateway and both my local internet and work VPN can work at the same time. However, when I disconnect from VPN and reconnect again, I can't ping our servers even though the connection status is "Connected". When I do route print my previously added route is listed but it doesn't seem to work. So I try to execute that 'route add' command again and as expected, it tells me that The route addition failed: The object already exists. But - and that's the point - when I now try to ping our servers again, everything works! So every time, I have to execute this route add command that will fail but fix the issue at the same time. Any ideas what I might be doing wrong? My PC is Windows 7 x64, I am Administrator, UAC is enabled and the command prompt is run with elevated privileges.

  Read the article

• Windows HTTP proxy client to pass service requests to VPN

  - by Chris

  I've got access to a network via CheckPoint VPN (Windows client). Problem is, I have a linux box that needs to talk to its web services and the target web servers are inside the VPN. So far, we have been unable to connect linux to the VPN (and I'm not trying to solve that problem at the moment). I'm wondering if (temporarily) I can setup a proxy server on a Windows (XP) box to shuttle HTTP requests back and forth? If so, what'd be a good application to do this? (hopefully free/open-source) TIA

  Read the article

• Windows 2008 Server in Amazon EC2 stops responding when SSTP/VPN connection is closed

  - by user38349

  All, I have a single Windows 2008 server running in Amazon's EC2 cloud. It's running a web application that is running fine and is accessible to the outside world. I need 3-5 developers to be able to work on database on the server, and was intending to accomplish this by setting up SSTP/RRAS on the server and letting them VPN in. This has been a bit of an ordeal due to the amount of server roles and messing with certificates that has been needed, but my VPN connection works now (all clients will be Windows 7). My problem is that when I drop my VPN connection (from the client side) the server hangs. The only way that I've found to get it back is to reboot it from the Amazon management console. Thanks for any guidance. Duncan

  Read the article

• Windows 2008 Server in Amazon EC2 stops responding when SSTP/VPN connection is closed

  - by user38349

  All, I have a single Windows 2008 server running in Amazon's EC2 cloud. It's running a web application that is running fine and is accessible to the outside world. I need 3-5 developers to be able to work on database on the server, and was intending to accomplish this by setting up SSTP/RRAS on the server and letting them VPN in. This has been a bit of an ordeal due to the amount of server roles and messing with certificates that has been needed, but my VPN connection works now (all clients will be Windows 7). My problem is that when I use my VPN connection (from the client side) the server hangs - although not at any any consistent place, sometimes it's when I close the connection, some times when I'm making the connection). The only way that I've found to get it back is to reboot it from the Amazon management console. Thanks for any guidance. Duncan

  Read the article

• Set up proxy for vpn server on ubuntu server 12.4

  - by Morteza Soltanabadiyan

  I have a vpn server with HTTPS, L2TP, OPENVPN, and PPTP. I want to set up a proxy on the server, so all connection that comes from vpn clients, they will use that. I created the following bash script file for it, but the proxy isn't working. gsettings set org.gnome.system.proxy mode 'manual' gsettings set org.gnome.system.proxy.http enabled true gsettings set org.gnome.system.proxy.http host 'cproxy.anadolu.edu.tr' gsettings set org.gnome.system.proxy.http port 8080 gsettings set org.gnome.system.proxy.http authentication-user 'admin' gsettings set org.gnome.system.proxy.http authentication-password 'admin' gsettings set org.gnome.system.proxy use-same-proxy true export http_proxy=http://admin:[email protected]:8080 export https_proxy=http://admin:[email protected]:8080 export HTTP_PROXY=http://admin:[email protected]:8080 export HTTPS_PROXY=http://admin:[email protected]:8080 What to do to make a global proxy for server and all vpn clients to use it automatically?

  Read the article

• set proxy for vpn server on ubuntu server 12.4

  - by Morteza Soltanabadiyan

  I have a vpn server with HTTPS, L2TP , OPENVPN , PPTP. i want to set proxy in the server so all connection that comes from vpn clients use the proxy that i set in my server. I made a bash script file for it , but proxy not working. gsettings set org.gnome.system.proxy mode 'manual' gsettings set org.gnome.system.proxy.http enabled true gsettings set org.gnome.system.proxy.http host 'cproxy.anadolu.edu.tr' gsettings set org.gnome.system.proxy.http port 8080 gsettings set org.gnome.system.proxy.http authentication-user 'admin' gsettings set org.gnome.system.proxy.http authentication-password 'admin' gsettings set org.gnome.system.proxy use-same-proxy true export http_proxy=http://admin:[email protected]:8080 export https_proxy=http://admin:[email protected]:8080 export HTTP_PROXY=http://admin:[email protected]:8080 export HTTPS_PROXY=http://admin:[email protected]:8080 Now , i dont know what to do to make a global proxy for server and all vpn clients use it automatically.

  Read the article

• Juniper SRX1400 VPN

  - by ank

  I have been trying to set up a client VPN on a Juniper SRX1400 without much success. All documentation I found from Juniper and elsewhere does a lot of other (difficult and wonderful) things other than the simple things I want to do. We already have a VPN running on CISCO PIX hardware which we need to put to rest and we pretty much like to replicate the functionality, which is: 1) client makes a request to the outside interface of the SRX1400, 2) client gets authenticated, 3) if successful, then client is assigned all the usual DHCP stuff and becomes part of the network. What privileges this DHCP assigned network has, should be configurable of course with the usual routing/filtering methods. Am I asking for too much from the SRX for this kind of thing? Should I ditch the SRX for VPN and revert to an OpenVPN solution that I had working some time back also and was amazed at the ease of configuration, functionality and features?

  Read the article

• Apache doesn't autostart because vpn isn't up yet.

  - by Col. Shrapnel

  I have a FreeBSD8 server, and VPN connection to my ISP. I use mpd5 and it works fine. A have an Apache server whch works fine, if I start it manually, after VPN is get up. But when I add it to rc.conf autostart, it fail to start, saying (49) can't assign requested address: make_sock could not bind to address I suppose it's because VPN isn't up yet and no IP address assigned to the interface which i set in the Listen directive in the httpd.conf. If i set Listen to the existing 127.0.0.1, it fail to serve wan requests. Is there a solution, either to delay apache autostart or configure it some different?

  Read the article

• Remote support via VPN without split tunnel

  - by Robe Eleckers

  my title might not be very clear, but I'll explain my setup in more detail now. We have several customers (companies) that need to be remotely supported. At these customers we have servers running with our software that needs to be serviced. These servers are (almost) never connected to the internet. For this we have multiple PC's running VPN clients. These PC's run a VNC server so our service engineers can login from their home laptop remotely to these PC's and connect from there to our customer via the VPN connection on the PC. The problem is however that several customers do not allow split tunneling. That means that when we connect via VPN to such a customer the VNC connection drops. Our current workaround is using a Citrix VM which we control via XenCenter console, but it's quite slow. Are there common solutions to handle this?

  Read the article

• VPN Connected, How to browse files? Windows Vista

  - by Wbdvlpr

  I am trying to establish a VPN connection to a server in my office from my laptop at home. I tried some of the steps as mentioned here: Connect to a network Connect to a workplace Use my Internet Connection (VPN) Then type server IP address and then my username & password. After creating a VPN connection, I can see I am connected to it. Now I want to browse files on the server. But I have no clue where I should look for them. I was thinking more of a simple step, like, Windows Run > Type ip address > \\124.345.678.900, then a prompt asking username and password, and finally a window opens to view the files. I tried to google it, but still unable to view files. Please help. Update: I didn't mention that when I try to connect to server via \\124.345.678.900 I get 0x80070043 error message.

  Read the article

• Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

  - by SnAzBaZ

  I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

  Read the article

• VPN doesn't have access to drives unless I use the default gateway

  - by Seb

  I am trying to setup a VPN connection on one of our office servers so that many of our employees can access our drives when out of town or for important business meetings. However I have a weird glitch in where if the default gateway option is checked they can see the drives and files, but get no internet access. If I have the default gateway option unchecked then they have there internet and can successfully connect to the VPN, but they are not able to see any of the drives or files. The server is running Windows Server 2003 Standard while the employees run either XP or 7 Professional. Any help is greatly appreciated. Thank you. EDIT The VPN setup is PPTP and the main server is behind a SonicWall if that is of any importance.

  Read the article

• Remote Desktop fails after VPN connection.

  - by Samet Sorgut

  The remote computer is connected with Remote Desktop. When the remote computer is connected to VPN the Remote Destop freezes. It is not possible to connect to the remote computer again via Remote Desktop. What can be done to connect to this remote computer after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest?

  Read the article

• Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

  - by SnAzBaZ

  I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

  Read the article

• Can't access dfs namespace over vpn

  - by cpf

  Hi Serverfault, I've recently configured 2 servers in AD on the same domain level. They are physically separated and permanently connected through a site-to-site vpn for dfs replication. All well, but when users connect to either site through vpn (from home e.g.) they can't use the domain level method: \\domain.com\data Internally this works perfectly, resolving domain.com when connected through vpn gets the correct IP. I've tried Google to figure things out. What I was able to find was that more people have this issue, no real solution found though. Can anyone explain why this is happening? Especially a solution would be really helpful! Thanks in advance.

  Read the article

• Sharing VPN from XP to Linux virtual

  - by user55513

  Hi I will keep the question simple with few details, if more is needed tell me. Thanks. I am playing around with networking and virtualbox. So I have 2 virtual machines. One is windows xp and another has linux in it. Windows XP has 2 network cards. One for the internet and the other to connect to the linux computer. Linux has one 1 card and it can only access the internet passing through Windows XP. Internet works fine until I activate OpenVPN on Windows. When I turn on VPN, Linux has no access to it. How can I make linux use VPN too? I believe it has something to do with using the "route" command on XP to send VPN traffic to Linux but I was not able to figure it out how yet.

  Read the article

• Security of a free public VPN service

  - by Mark Belli

  I just started using VPNBOOK, which is a (very efficent) free VPN solution. I have a question: VPNBOOK user and pass used to connect to their vpn network are publicily available on their homepage; everybody uses them to connect to the vpn. Can a user intercept my wifi traffic and: Understand that my connections are directed to VPNBOOK servers. If point 1 is successful, then they could use VPNBOOK public user and pass to decrypt my traffic? I hope I am missing something, otherwise it would be a very big weakness and I would revert to a paid service (with a private account)

  Read the article

• Netgear VPN can't access specific server

  - by Critologist

  I have a Netgear FVS318N configured with a VPN. I'm trying to access my call recorder with the provided software from another office. I've already setup the VPN connection, and it works. I can connect and ping the remote router and a few other things on the network. However, I can't ping or connect to my call recorder. If I move outside of the office network (i.e. connect directly to the cable modem or via a mobile hotspot), I can connect and ping the call recorder just fine. The office has a simple Linksys WRT54G router and is using AT&T Uverse. The remote location is using Charter Cable with a Netgear FVS318N. Has anyone ever encountered anything like this before? I've setup an identical VPN previously for a different client using similar hardware and never encountered this. Thanks in advance!

  Read the article

• OS X server VPN local ip

  - by gbrandt

  Hi all, I have 10.6.2 server on the internet. I want to vpn into it to get access. I start VPN and it gives me an address in the range I have set 192.168.2.100-192.168.2.105. However the server itself does not have a local ip of 192.168.2.x so I cannot ping it or ssh into it or anything. The machine VPNing gets an ifconfig entry that looks like this: ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1280 inet 192.168.2.100 --> 70.72.xxx.xxx netmask 0xffffff00 Where I think it should get: ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1280 inet 192.168.2.100 --> 192.168.2.1 netmask 0xffffff00 I can't find anywhere to set the local vpn IP address. And I can't find a pptpd.conf file either. Any help is appreciated.

  Read the article

• VPN connects but my browsers and messenger don't connect

  - by elizabeth chubbuck

  I have no problem VPN into work. As of last night, everything worked fine. But as of this A.M., none of my browsers connect and Microsoft Messenger will not connect. I did nothing, but had a pending a OSX update. I rebooted.. Still no internet. All network connections working, clearly, since VPN works. Its how I am doing this post now, is via VPN and remote desktopping to work computer. This just showed up as of this morning not working. I renewed DHCP, etc.. but cannot ping anywhere.

  Read the article

• configure vpn so that it is not the preferred route

  - by pstanton

  Hi all, I recently re-installed XP on my PC. I had a vpn set up on the old system and remember being advised to change one setting so that it wasn't the preferred route for all network traffic. This was ideal as only connections to the target network would be made through the vpn and all normal traffic would go through the regular path unmolested. i remember thinking "why isn't this the default setting!?". now i've formatted my drive and lost the config for that vpn (besides host, username, passwd). does anyone know of the setting i'm referring to? thanks, paul.

  Read the article

• Increase the compression performance of VPN

  - by Martin

  I am currently switching from a system with HPN-SSH tunnels and enabled compression to something VPN based. I have tried tinc and n2n so far, hamachi requires a library I do not have. In my primitive benchmarks I am not satisfied with the achievable bandwidth compared to the SSH tunnels. In tinc the low LZO setting performed best, but compression is only available in UDP mode. Ideally I would like to have a TCP-based VPN with a multi-threaded compression. Can you suggest me some ideas how to increase the performance? Would it be possible to somehow put a compression filter in front of the tun interface? Or are there any VPN implementations that might be better suited for my needs (fast compression, TCP-based, switch mode, does not have to be super-secure)? I would consider tunnelling Ethernet over SSH, but according to some articles it is not advisable.

  Read the article

• Windows 7 default VPN - Single Click to Connect

  - by Goyuix

  The default way to connect to a VPN (standard includedd MS client) seems to be to click on the network icon in the system tray to expand it, then pick the VPN connection, and click the connect button. This brings up a dialog where you can enter your username and password. I have told the VPN connection to remember my credentials. Is there some way I can skip that dialog and just have it connect? I have tried using rasdial.exe, and I can connect as long as I pass the username and password as arguments. It doesn't seem to want to use the stored credentials for some reason, maybe I need to store them with an elevated account.

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >