Search Results

Search found 780 results on 32 pages for 'trunk'.

Page 16/32 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

• Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

  - by MasterRoot24

  I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Switching branches using Ankh, error: "the working copy lock appears to be broken" VS 2008

  - by nailitdown

  As title says. Current working copy is fully committed, i go to Subversion Switch, change the url from the current branch to the trunk, receive a popup that says Working copy not locked The working copy lock appears to be broken Any ideas why?

  Read the article

• Relative Path in Subversion external configuration

  - by sundar venugopal

  is there any way to use Relative path when configuring subversion externals. for example Trunk - directoryA - directoryB - projectA {external DirectoryB} for configuring ProjectA we have to configure full path in the external property. which is causing problems or forcing us to do change the properties when we do branches. any way to automate the branching process or fix with absolute path will be useful

  Read the article

• Unshelving in TFS: What does it mean?

  - by lividsquirrel

  Here's the part I get: When you shelve in TFS, it makes a server copy of the changes so they are not lost, but does not check them into the source code trunk/branch you are working on. Question: Under what circumstances would you use the "unshelve" feature? Does it mean it will remove the shelveset from the TFS server? Can you do a get from a shelveset? Or is it really just a diff description between the shelveset and the "real" source code?

  Read the article

• TeamCity & Subversion: Checkout copies ALL tags to buildagent's checkout directory

  - by El Bauldo

  We have the following URL: URL: https://dev-01:8555/svn/Shop We have the following structure in SubVersion Shop --trunk --branches --tags The problem is, when I do a build, under the buildagent directory, I get every single tag in the repository copied over to the buildagent. Is there a way to only retrieve the HEAD revision to effect the build on.

  Read the article

• SVN (Subversion) Problem "File is scheduled for addition, but is missing" - Using Versions

  - by Mike

  I'm using Versions for SVN. I attempt to commit and get this message: Commit failed (details follow): '/Users/mike/Sites/mysite.com/astss-cvsdude/Trunk/cart/flashfile.swf' is scheduled for addition, but is missing I suppose this is because I had added files to the repo, and then deleted them via the filesystem. I'd like to have it simply make note of my change, and apply the change to the repo. How can I get around this?

  Read the article

• Cannot integrate Gallio MBUnit with Team City

  - by Bernard Larouche

  I have been trying to get my MBUnit tests suite to work on Team City for many days now without any success. My solution builds no problem. The program is with my tests. After googling for Gallio integration with Team City I tried many ways to make this thing work and I think I am close but need help. I have included the gallio bin directory to my repository and also on my TC Server. Here is my build runner set up in Team City : Build runner : MSBuild Build file path : Myproject.msbuild Targets : RebuildSolution RunTests Here is Myproject.msbuild file I created and included in the Source control trunk directory : <Project xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> <!-- This is needed by MSBuild to locate the Gallio task --> <UsingTask AssemblyFile="C:\Gallio\bin\Gallio.MSBuildTasks.dll" TaskName="Gallio" /> <!-- Specify the tests assemblies --> <ItemGroup> <TestAssemblies Include="C:\_CBL\CBL\CoderForTraders\Source\trunk\UnitTest\DomainModel.Tests\bin\Debug\CBL.CoderForTraders.DomainModel.Tests.dll" /> </ItemGroup> <Target Name="RunTests"> <Gallio IgnoreFailures="false" Assemblies="@(TestAssemblies)" RunnerExtensions="TeamCityExtension,Gallio.TeamCityIntegration"> <!-- This tells MSBuild to store the output value of the task's ExitCode property into the project's ExitCode property --> <Output TaskParameter="ExitCode" PropertyName="ExitCode"/> </Gallio> <Error Text="Tests execution failed" Condition="'$(ExitCode)' != 0" /> </Target> <Target Name="RebuildSolution"> <Message Text="Starting to Build"/> <MSBuild Projects="CoderForTraders.sln" Properties="Configuration=Debug" Targets="Rebuild" /> </Target> </Project> Here are the errors displayed by Team City : error MSB4064: The "Assemblies" parameter is not supported by the "Gallio" task. Verify the parameter exists on the task, and it is a settable public instance property error MSB4063: The "Gallio" task could not be initialized with its input parameters. Thanks for your help

  Read the article

• Imageview ontop of another imageview

  - by Joelbitar

  I have a listlayout with items in it that looks like this: There is firs an ImageView (the light) and then two textViews. All of this inside a TableLayout. (source here: http://code.google.com/p/switchctrl/source/browse/trunk/android/res/layout/device_switch.xml) I want to have a rotating animation of a loading indicator Ontop of this light when this particular device (light) performs an action or an action is performed on it. How do I put an animation ontop of this light imageview?

  Read the article

• I need help with this ogre dependent header (Qgears)

  - by commodore

  I'm 2 errors away from compiling Qgears. (Hacked Version of the Final Fantasy VII Engine) I've messed with the preprocessors to load the actual location of the ogre header files. Here are the errors: ||=== qgears, Debug ===| /home/cj/Desktop/qgears/trunk/project/linux/src/core/TextManager.h|48|error: invalid use of ‘::’| /home/cj/Desktop/qgears/trunk/project/linux/src/core/TextManager.h|48|error: expected ‘;’ before ‘m_LanguageRoot’| ||=== Build finished: 2 errors, 0 warnings ===| Here's the header file: // $Id$ #ifndef TEXT_MANAGER_h #define TEXT_MANAGER_h #include <OGRE/OgreString.h> #include <OGRE/OgreUTFString.h> #include <map> struct TextData { TextData(): text(""), width(0), height(0) { } Ogre::String name; Ogre::UTFString text; int width; int height; }; typedef std::vector<TextData> TextDataVector; class TextManager { public: TextManager(void); virtual ~TextManager(void); void SetLanguageRoot(const Ogre::String& root); void LoadTexts(const Ogre::String& file_name); void UnloadTexts(const Ogre::String& file_name); const TextData GetText(const Ogre::String& name); private: struct TextBlock { Ogre::String block_name; std::vector<TextData> text; } Ogre::String m_LanguageRoot; // Line #48 std::list<TextBlock> m_Texts; }; extern TextManager* g_TextManager; #endif // TEXT_MANAGER_h The only header file that's in include that's not a ogre header file is "map". If it helps, I'm using the Code::Blocks IDE/GCC Compiler in GNU/Linux. (Arch) I'm not sure even if I get this header fixed, I think I'll have build errors latter, but it's worth a shot. Edit: I added the semicolon and I have one more error in the header file: error: expected unqualified-id before ‘{’ token

  Read the article

• How do I add older versions of code into a Subversion repository as tagged versions

  - by TheoJones

  When we finally started using source control, old versions of code were added into the SVN in their own discrete folders, so I ended up with root \libv4 \libv4.2 \lib4.3 \lib5 What I would like to get to is having these older versions of the code as tagged versions inside the repository, like this: root \lib \tags \v4 \v4.2 \v4.3 \v5.0 \trunk how would I go about doing this? I'm using Tortoise SVN on the client side, and visualSVN server at the back.

  Read the article

• understanding P4 describe / diff summary (-ds) option

  - by JavaScriptDude

  Greetings P4 folks, I am trying to understand the P4 describe -ds output. I am assuming that this is the same as the p4 diff -ds output. Here is an example of the "Differences ..." block: ==== //depot/Groups/mygroup/trunk/main/FooBar.java#5 (text) ==== add 7 chunks 13 lines deleted 1 chunks 1 lines changed 16 chunks 92 / 118 lines ~ Now I understand that add and deleted lines are clear but why are there two numbers for the changed lines (92 / 118). Thanks! - JsD

  Read the article

• SVN merge loses files and code

  - by SyBer

  Hi. I'm trying to merge trunk change-set into a branch, but have found out a lot of post-merge issues, including whole files that disappeared, and missing code blocks I'm using SVN 1.6 for both clients and server. Tried this with multiple clients - Eclipse, Netbeans and SVN - the result is the same. Can someone advice how sort it out, and most important, prevent code loss? Thanks in advance!

  Read the article

• SVN: Create a dump file of a folder

  - by DarkJaff

  I'm trying to create a dump file of a folder in my SVN repository.(My goal is to import this dump on another repository, but that's another story). I've read like 20 pages about this and they all tell me to use svndumpfilter but I can't seem to make it work. Here is my command: C:\>svnadmin dump d:/SvnData/TestingSVN/ | svndumpfilter include /TestingSVN/Trunk/Fms/ > d:\FMS.txt The output in the command line is this strange thing: Including prefixes: '/TestingSVN/Trunk/Fms' * Dumped revision 0. Revision 0 com*m iDtutmepde da sr e0v.isi n 1. Revision 1 committed as 1. * Dumped revision 2. Revision 2 committed a*s D2u.mpe revision 3. Revisio*n D3u mcpoemdm irtetveids iaosn 34.. Revision* 4D ucmopmemdi trteevdi saiso n4 .5. Revision 5 com*m iDtutmepde da sr e5v.isi n 6. Revision 6 commi*t tDeudm paesd 6r.evi ion 7. Revisio*n D7u mcpoemdm irtetveids iaosn 78.. Revision *8 Dcuommpmeidt treedv iassi o8n. 9. Revision 9* cDoummmpietdt erde vaiss i9o.n 1 . Revisi*o nD u1m0p ecdo mrmeivtitseido na s1 11.0 . Revision 11 *c oDmummiptetde dr eavsi s1i1o.n 1 . Revision 12 committed* aDsu m1p2e.d r vision 13. Revision 13 committ*e dD uamsp e1d3 .rev sion 14. Revision 14 commit*t eDdu mapse d1 4r.evi ion 15. Revision 15 committed as 15. * Dumped revision 16. Revision 16 committed as 16. Dropped 83 nodes: '/Branches' '/Branches/305' '/Branches/305/New Text Document.txt' '/Fms' '/Fms/ADPropertySheet.cpp'** etc. for 83 nodes... Also, the dump file itself is only 3 kb and contain no real data, only things like that (this is not the complete dump, just a sample) SVN-fs-dump-format-version: 2 UUID: 592fc9f0-5994-e841-a4dc-653714c95216 Revision-number: 0 Prop-content-length: 56 Content-length: 56 K 8 svn:date V 27 2009-06-19T15:05:52.001352Z PROPS-END Revision-number: 1 Prop-content-length: 112 Content-length: 112 K 7 svn:log V 38 This is an empty revision for padding. K 8 svn:date V 27 2009-06-19T15:11:29.378511Z PROPS-END Can anybody help me sort this out?

  Read the article

• How do I use continuations on Scala 2.8?

  - by Seth Tisue

  Scala 2.8.0.RC1 includes the continuations plugin on trunk for the first time, but the details of how to use it have changed from previous releases, so it's difficult to follow the blog entries and SO answers out there that talk about continuations but were written for previous versions.

  Read the article

• Load SQL dump in PostgreSQL without the password dependancy

  - by Cédric Girard

  Hi, I want my unit tests suite to load a SQL file in my database. I use a command like "C:\Program Files\PostgreSQL\8.3\bin"\psql --host 127.0.0.1 --dbname unitTests --file C:\ZendStd\www\voo4\trunk\resources\sql\base_test_projectx.pg.sql --username postgres 2>&1 It run fine in command line, but need me to have a pgpass.conf Since I need to run unit tests suite on each of development PC, and on development server I want to simplify the deployment process. Is there any command line wich include password? Thanks, Cédric

  Read the article

• Where is Castle's AbstractFacility class?

  - by ripper234

  I am trying to compile Castle.Facilities.ActiveRecordIntegration with the trunk version of Castle.Core. ARIntegration uses 'AbstractFacility', which sits in the Castle.MicroKernel DLL. The DLL is now nowhere to be found. Where is ARIntegration/MicroKernel? How do I proceed?

  Read the article

• Unable to checkout log4j repository

  - by ankit

  I'm using tortoiseSVN to checkout the log4j v1.2 source from - http://svn.apache.org/repos/asf/logging/log4j/trunk But i keep getting this error: Error: OPTIONS of '': Could not Error: resolve hostname `svn.apache.org': No such host is known. The funny thing is that i can access 'svn.apache.org' from my browser but if i try to ping it from the command prompt, it says host not found. Does any body else face this problem? Is there any other way to get the source for log4j v1.2?

  Read the article

• What are the differences between GIT and SVN when it comes to merge conflicts solving.

  - by chalup

  I keep hearing that branching in git is so much easier than in SVN, because it's easier to merge the branch back to trunk/master. I've read some tutorials, but they only covered basic merge conflicts ("Alice changed line 8 of code.cpp and at the same time Bob changed line 8 of code.cpp...") and there are no differences between SVN and all other distributed source control systems. Can you give me the examples of changes in branch that would cause troubles in SVN repository, but would be handled gracefully by git?

  Read the article

• What does this Eclipse icon mean in a Merge Results view?

  - by user68759

  I just did an svn merge from a branch to a trunk in my Eclipse IDE, and in the Merge Results view, there is this following icon: I am dying to know what it means. I have searched the entire Eclipse documentation and some relevant StackOverflow questions, but couldn't find anything. The CollabNet documentation about Merge Results View explains what a Merge Results View is, but doesn't mention anything about the meanings of its icons. Does anyone know? Thanks!

  Read the article

• XML Parsing need help iphone sdk

  - by neha

  Hi all, How do you get "MayurS123" from following xml tag by parsing? <eletitle lnk="http://192.168.10.2/justmeans/trunk/newsfeed/mayurs">MayurS123 Sharma</eletitle> My file is getting parsed properly. Here I'm able to retrieve the lnk component by doing: if([elementName isEqualToString:@"eletitle"]) { aGoodwork.lnk = [attributeDict objectForKey:@"lnk"]; } But I'm not getting how to get in actual title. Thanx in advance.

  Read the article

• how do i download source code using svn on OS X?

  - by Moshe

  How can I get source code off the internet using SVN? I'm trying to download Oolong game engine for iPhone OS. I am on Mac OS X 10.6 with XCode 3.2.2. svn checkout http://oolongengine.googlecode.com/svn/trunk/ oolongengine-read-only is the command I got from the Oolong Google Code page.

  Read the article

• What's the difference between tiny, huge and small in vim on MacPorts

  - by TK

  I'm trying to install vim via MacPorts. I found this port at http://trac.macports.org/browser/trunk/dports/editors/vim/Portfile. There are variants like tiny, small and huge. Is there any way to tell which variant installs what features?

  Read the article

• error 127 when running "git svn init" on cygwin

  - by Michael Borgwardt

  I'm trying to convert a local SVN repository to git using git-svn under cygwin and failing. This is what happens: $ git svn init -t tags -b branches -T trunk file:///cygdrive/e/repository/project init: command returned error: 127 Any ideas?

  Read the article

• JQuery autocomplete: is not working asp.net

  - by Abu Hamzah

  is that something wrong in the below code? its not firing at all edit <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="HostPage.aspx.cs" Inherits="HostPage" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server"> <title>Untitled Page</title> <script type="text/javascript" src="http://ajax.googleapis.com/ajax/libs/jquery/1.4/jquery.min.js"></script> <script type="text/javascript" src="http://ajax.googleapis.com/ajax/libs/jqueryui/1.8/jquery-ui.min.js"></script> <link rel="stylesheet" href="http://dev.jquery.com/view/trunk/plugins/autocomplete/jquery.autocomplete.css" type="text/css" /> <script type="text/javascript" src="http://dev.jquery.com/view/trunk/plugins/autocomplete/jquery.autocomplete.js"></script> </head> <body> <form id="form1" runat="server"> <script type="text/javascript"> $(document).ready(function() { $("#<%=txtHost.UniqueID %>").autocomplete("HostService.asmx/GetHosts", { dataType: 'json' , contentType: "application/json; charset=utf-8" , parse: function(data) { var rows = Array(); debugger for (var i = 0; i < data.length; i++) { rows[i] = { data: data[i], value: data[i].LName, result: data[i].LName }; } return rows; } , formatItem: function(row, i, max) { return data.LName + ", " + data.FName; } }); }); </script> <div> <asp:Label runat="server" ID='Label4' >Host Name:</asp:Label> <asp:TextBox ID="txtHost" runat='server'></asp:TextBox> <p> </div> </form> </body> </html>

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >