Search Results

Search found 5206 results on 209 pages for 'dr rocket mr socket'.

Page 160/209 | < Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >

• Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe

  Read the article

• ubuntu box just redisplaying login screen after update

  - by David M. Karr

  My Ubuntu 12.04 box has been working fine. A recent update may have messed something up. I normally run remote windows on it, and I noticed that my windows were failing to start up. I then tried logging into it directly from the GUI console, and I'm seeing that after I press enter on the (valid) password, the page just redisplays. It's not a password error, as that would give me an inline error. I see some messages appear and disappear quickly between the login screen going away and then redisplaying, but they go away too quickly to read. I was able to run the non-gui login, and I did an update and upgrade, and then rebooted, but it's doing the same thing. I have a Samba connection from my Windows box, and that's still working. If it matters, here's my uname output (somewhat elided): Linux ... 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux What can I do to troubleshoot this? Note that when I select "Guest Session", it lets me log in and displays the window manager. This seems significant to me. Does this mean that something specific to my login is causing it to fail? Note: If it matters, here's the output from /var/log/dmesg. The line about gdm seems interesting: [ 9.815883] Bluetooth: RFCOMM TTY layer initialized [ 9.815887] Bluetooth: RFCOMM socket layer initialized [ 9.815888] Bluetooth: RFCOMM ver 1.11 [ 9.879088] [PCSPP,TRISTATE] [ 9.879092] parport0: irq 7 detected [ 9.883935] type=1400 audit(1341871177.871:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=845 comm="apparmor_parser" [ 9.884365] type=1400 audit(1341871177.871:11): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=851 comm="apparmor_parser" [ 9.950397] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X [ 9.961160] init: gdm main process (907) killed by TERM signal [ 9.966358] lp0: using parport0 (polling).

  Read the article

• Determinism in multiplayer simulation with Box2D, and single computer

  - by Jake

  I wrote a small test car driving multiplayer game with Box2D using TCP server-client communcations. I ran 1 instance of server.exe and 2 instance of client.exe on the same machine that I code and compile the executables. I type inputs (WASD for a simple car movement) into one of the 2 clients and I can get both clients to update the simulation. There are 2 cars in the simulation. As long as the cars do not collide, I get the same identical output on both client.exe. I can run the car(s) around for as long as I could they still update the same. However, if I start to collide the cars, very quickly they go out of sync. My tools: Windows 7, C++, MSVS 2010, Box2D, freeGlut. My Psuedocode: // client.exe void timer(int value) { tcpServer.send(my_inputs); foreach(i = player including myself) inputs[i] = tcpServer.receive(); foreach(i = player including myself) players[i].process(inputs[i]); myb2World.step(33, 8, 6); // Box2D world step simulation foreach(i = player including myself) renderer.render(player[i]); glutTimerFunc(33, timer, 0); } // server.exe void serviceloop { while(all clients alive) { foreach(c = clients) tcpClients[c].receive(&inputs[c]); // send input of each client to all clients foreach(source = clients) { foreach(dest = clients) { tcpClients[dest].send(inputs[source]); } } } } I have read all over the internet and SE the following claims (paraphrased): Box2D is deterministic as long as floating point architecture/implementation is the same. (For any deterministic engine) Determinism is gauranteed if playback of recorded inputs is on the same machine with exe compiled using same compiler and machine. Additionally my server.exe and client.exe gameloop is single thread with blocking socket calls and fixed time step. Question: Can anyone explain what I did wrong to get different Box2D output?

  Read the article

• Exchange 2010 Deployment Notes - ISA 2004 Server Issue

  - by BWCA

  An interesting ISA 2004 tidbit … While we were setting up our Exchange 2010 ActiveSync environment, we encountered a problem where we could not successfully telnet over port 443 from one of our ISA 2004 Servers to our Exchange 2010 Client Access Server Array. When we tried to telnet over port 443 from the ISA Server to the Client Access Server Array name, we would get a “Could not open connection to the host on port 443: Connect failed” error message. Also, when we used portqry over port 443 from the ISA Server to the Client Access Server Array name, we would get a “Error opening socket: 10065” and “No route to host” error messages. It was odd because we did not have any problems with using ping or tracert from the ISA Server to the Client Access Server Array and our firewall firewall policy was allowing 443 traffic to pass through. After some troubleshooting, we were able to telnet and use portqry over port 443 successfully if we stopped the Microsoft Firewall service on the ISA 2004 Server.  So, it was strictly a problem with ISA.  Eventually, we were able to isolate the problem to a ISA 2004 Server System Policy setting as shown below (to modify the System Policy, right-click Firewall Policy and click Edit System Policy). Under the Diagnostics Services – HTTP Connectivity verifiers Configuration Group, you need to enable the configuration group under the General tab to resolve the problem.  After we enabled the setting, we no longer had a problem.

  Read the article

• Hired developer insists on doing things the wrong way

  - by Tariq- iPHONE Programmer

  Hello, i am working with Social Networking iphone app which require remote data connection. So i hired a php developer in order to provide me RESTful services. But when i start working with him, he arguing me that he will not make stored procedures and web services. Instead of he suggested me to pass query as a parameter. Suppose If I have to call Search service, he told me to send POST request with 3 parameters: Query="select * from users", username=abd and password = 123 And i thing there is no such architecture in order to use remote data. Then he is saying it is possible through socket programming. And I am 100% sure this is not an appropriate way to access remote data. This is simply illogical. Thousands of iphone application using REST/SOAP services to make remote data connection He just declined me to provide RESTful services. Please its my heartily advice to all developers that post your own views over here. So that I can show to that developers that these are the views from all developers worldwide.

  Read the article

• "Oracle Coherence 3.5" Book - My Humble Review

  - by [email protected]

    After reviewing the book in more detail I say again that it is a great guide for sure. Lots of important concepts that sometimes can be somewhat confusing are deeply reviewed, including all types of caching schemes and backing maps, and the cache topologies with their corresponding performances and very useful "When to use it?" sections. Some functionalities that are very desirable or used a lot are reviewed with examples and best practices of implementation, including: Data affinity Querying Pagination Indexes Aggregations Event processing, listening and triggering Data persistence Security Regarding the networking and architecture topics, Coherence*Extend is exhaustively reviewed, including C++ and .NET clients, with very good tips and examples, even including source codes. Personally, I am also glad to see that the address providers (<address-provider> tag), new feature in Coherence 3.5 which is a way to programmatically provide well-known addresses in order to connect to the cluster, is mentioned on the book, because it provides new functionalities to satisfy some special configuration requirements for example: Provide a way to switch extend nodes in cases of failure Implement custom load balancing algorithms and/or dynamic discovery of TCP/IP connection acceptors Dynamically assign TCP address and port settings when binding to a server socket Another very interesting and useful section is the "Coherent Bank Sample Application", which is a great tutorial, useful to understand how Coherence interacts with third party products establishing a clear integration with them, including the use of non-Oracle products like MS Visual Studio.  

  Read the article

• Delphi Client-Server Application using Firebird 2.5 error

  - by Japie Bosman

  I have got a lengthy question to ask. First of all Im still very new when it comes to Delphi programming and my experience has beem mostly developing small single user database applications using ADO and an Access database. I need to take the transition now to a client server application and this is where the problem starts. I decided to use Firebird 2.5 embeded as my database, as it is open source, and it is can be used with the interbase components in Delphi and that multiple clients can access the database simultanously. So I followed the interbase tutorial in Delphi. I managed to connect the client to the server and see the data in the example (While both are running on my pc), but when i tried to move the client to another pc, keeping the server on mine and running it to see if I can connect to the server it gave me the following error. Exception EIdSocketError in module clientDemo.exe at 0029DCAC. Socket Error # 10061 Connection refused. I understand that this might be because the host is defined as localhost in the client. But here is my first question. In the TSQLConncetion you can set die hostname under Driver-Hostname. The thing I want to know is how do you do this at run time, as I cannot get the property when I try and make an edit box to allow the user to enter the value and then set it via code like for example: SQLConncetion1.Driver.Hostname := edtHost.text; The thing is there is not such property to set, so how do you set the hostname at run time? Im using Delphi XE2 There is still a lot of questions to come especially when it comes to deployment, but I will take this piece by piece and I appreciate the advice.

  Read the article

• Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

  - by Tim

  Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

  Read the article

• Welcome To The Nashorn Blog

  - by jlaskey

  Welcome to all.  Time to break the ice and instantiate The Nashorn Blog.  I hope to contribute routinely, but we are very busy, at this point, preparing for the next development milestone and, of course, getting ready for open source. So, if there are long gaps between postings please forgive. We're just coming back from JavaOne and are stoked by the positive response to all the Nashorn sessions. It was great for the team to have the front and centre slide from Georges Saab early in the keynote. It seems we have support coming from all directions. Most of the session videos are posted. Check out the links. Nashorn: Optimizing JavaScript and Dynamic Language Execution on the JVM. Unfortunately, Marcus - the code generation juggernaut,  got saddled with the first session of the first day. Still, he had a decent turnout. The talk focused on issues relating to optimizations we did to get good performance from the JVM. Much yet to be done but looking good. Nashorn: JavaScript on the JVM. This was the main talk about Nashorn. I delivered the little bit of this and a little bit of that session with an overview, a follow up on the open source announcement, a run through a few of the Nashorn features and some demos. The room was SRO, about 250±. High points: Sam Pullara, from Twitter, came forward to describe how painless it was to get Mustache.js up and running (20x over Rhino), and,  John Ceccarelli, from NetBeans came forward to describe how Nashorn has become an integral part of Netbeans. A healthy Q & A at the end was very encouraging. Meet the Nashorn JavaScript Team. Michel, Attila, Marcus and myself hosted a Q & A. There was only a handful of people in the room (we assume it was because of a conflicting session ;-) .) Most of the questions centred around Node.jar, which leads me to believe, Nashorn + Node.jar is what has the most interest. Akhil, Mr. Node.jar, sitting in the audience, fielded the Node.jar questions. Nashorn, Node, and Java Persistence. Doug Clarke, Akhil and myself, discussed the title topics, followed by a lengthy Q & A (security had to hustle us out.) 80 or so in the room. Lots of questions about Node.jar. It was great to see Doug's use of Nashorn + JPA. Nashorn in action, with such elegance and grace. Putting the Metaobject Protocol to Work: Nashorn’s Java Bindings. Attila discussed how he applied Dynalink to Nashorn. Good turn out for this session as well. I have a feeling that once people discover and embrace this hidden gem, great things will happen for all languages running on the JVM. Finally, there were quite a few JavaOne sessions that focused on non-Java languages and their impact on the JVM. I've always believed that one's tool belt should carry a variety of programming languages, not just for domain/task applicability, but also to enhance your thinking and approaches to problem solving. For the most part, future blog entries will focus on 'how to' in Nashorn, but if you have any suggestions for topics you want discussed, please drop a line.  Cheers. 

  Read the article

• exception occurred for backend host '127.0.0.1/7001/7001': 'CONNECTION_REFUSED [os error=0, line 1715 of URL.cpp]: Error connecting to host 127.0.0.1:7001'

  - by Vijaya Moderator -Oracle

  When you hit the WLS Server via Proxy server, we may get the issue like below... [09/Jun/2014:06:05:50] failure ( 3284): for host 127.0.0.1 trying to GET /.../soundlink_wireless_​speaker/index.jsp, wl-proxy reports: exception occurred for backend host '127.0.0.1/7001/0': 'PROTOCOL_ERROR [line 835 of URL.cpp]: Backend Server not responding' [09/Jun/2014:06:05:50] failure ( 3284): for host 127.0.0.1 trying to GET /.../soundlink_wireless_​speaker/index.jsp, wl-proxy reports: exception occurred for backend host '127.0.0.1/7001/0': 'PROTOCOL_ERROR [line 835 of URL.cpp]: Backend Server not responding' [09/Jun/2014:06:05:51] failure ( 3284): for host 127.0.0.1 trying to GET /.../soundlink_wireless_​speaker/index.jsp, wl-proxy reports: exception occurred for backend host '127.0.0.1/7001/7001': 'CONNECTION_REFUSED [os error=0, line 1715 of URL.cpp]: Error connecting to host 127.0.0.1:7001' To solve the issue 1.  Check if there is any issue at the firewall by executing the below command     telnet 127.0.0.1 7001 2.  Also access  using the hostname instead of IP Address  If it errors out like below   Microsoft Telnet> o 127.0.0.1 7001 connecting to 127.0.0.1  Warning thrown at weblogic console: <BEA-000449> <Closing socket as no data read from it on 127.0.0.1:54,356 during the configured idle timeout of 5 secs>  Test the same again by disabling the firewall. Below are the steps... 1)Go to Start ----> Run  2)Type services.msc  3)In services.msc search for "Windows Firewall" and Right Click on "Windows Firewall"---->Select Stop. 4)Access the Weblogic URL  If the issue is resolved after disabling firewall, Request your  OS System Admin to open the port 7001 at the firewall end to access the application

  Read the article

• Is an event loop just a for/while loop with optimized polling?

  - by Alan

  I'm trying to understand what an event loop is. Often the explanation is that in the event loop, you do something until you're notified that an event occurred. You than handle the event and continue doing what you did before. To map the above definition with an example. I have a server which 'listens' in a event loop, and when a socket connection is detected, the data from it gets read and displayed, after which the server goes to the listening it did before. However, this event happening and us getting notified 'just like that' are to much for me to handle. You can say: "It's not 'just like that' you have to register an event listener". But what's an event listener but a function which for some reason isn't returning. Is it in it's own loop, waiting to be notified when an event happens? Should the event listener also register an event listener? Where does it end? Events are a nice abstraction to work with, however just an abstraction. I believe that in the end, polling is unavoidable. Perhaps we are not doing it in our code, but the lower levels (the programming language implementation or the OS) are doing it for us. It basically comes down to the following pseudo code which is running somewhere low enough so it doesn't result in busy waiting: while(True): do stuff check if event has happened (poll) do other stuff This is my understanding of the whole idea, and i would like to hear if this is correct. I am open in accepting that the whole idea is fundamentally wrong, in which case I would like the correct explanation. Best regards

  Read the article

• Randomely loosing wireless connexion with Cubuntu 12.04

  - by statquant

  I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• root folder php scripts not running in nginx

  - by Thermionix

  nginx with php-fpm on ubuntu 12.04 server. attempting to access /var/www/test.php (via https://example.net/test.php) downloads the script instead of executing it. if I place the test.php in a subdirectory, i.e. /var/www/test/test.php it executes. root.conf; root /var/www; include php-fpm.conf; location ~ /\. { access_log off; log_not_found off; deny all; } php-fpm.conf; location ~ \.php$ { try_files $uri =404; fastcgi_pass unix:/var/run/php5-fpm.socket; include fastcgi_params; } fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_index index.php; fastcgi_param HTTPS on; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; #fastcgi_param SCRIPT_FILENAME $request_filename; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200;

  Read the article

• How do I mount a CIFS share via FSTAB and give full RW to Guest

  - by Kendor

  I want to create a Public folder that has full RW access. The problem with my configuration is that Windows users have no issues as guests (they can RW and Delete), my Ubuntu client can't do the same. We can only write and read, but not create or delete. Here is the my smb.conf from my server: [global] workgroup = WORKGROUP netbios name = FILESERVER server string = TurnKey FileServer os level = 20 security = user map to guest = Bad Password passdb backend = tdbsam null passwords = yes admin users = root encrypt passwords = true obey pam restrictions = yes pam password change = yes unix password sync = yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . add user script = /usr/sbin/useradd -m '%u' -g users -G users delete user script = /usr/sbin/userdel -r '%u' add group script = /usr/sbin/groupadd '%g' delete group script = /usr/sbin/groupdel '%g' add user to group script = /usr/sbin/usermod -G '%g' '%u' guest account = nobody syslog = 0 log file = /var/log/samba/samba.log max log size = 1000 wins support = yes dns proxy = no socket options = TCP_NODELAY panic action = /usr/share/samba/panic-action %d [homes] comment = Home Directory browseable = no read only = no valid users = %S [storage] create mask = 0777 directory mask = 0777 browseable = yes comment = Public Share writeable = yes public = yes path = /srv/storage The following FSTAB entry doesn't yield full R/W access to the share. //192.168.0.5/storage /media/myname/TK-Public/ cifs rw 0 0 This doesn't work either //192.168.0.5/storage /media/myname/TK-Public/ cifs rw,guest,iocharset=utf8,file_mode=0777,dir_mode=0777,noperm 0 0 Using the following location in Nemo/Nautilus w/o the Share being mounted does work: smb://192.168.0.5/storage/ Extra info. I just noticed that if I copy a file to the share after mounting, my Ubuntu client immediately make "nobody" be the owner, and the group "no group" has read and write, with everyone else as read-only. What am I doing wrong?

  Read the article

• Server-side Architecture for Online Game

  - by Draiken

  basically I have a game client that has communicate with a server for almost every action it takes, the game is in Java (using LWJGL) and right now I will start making the server. The base of the game is normally one client communicating with the server alone, but I will require later on for several clients to work together for some functionalities. I've already read how authentication server should be sepparated and I intend on doing it. The problem is I am completely inexperienced in this kind of server-side programming, all I've ever programmed were JSF web applications. I imagine I'll do socket connections for pretty much every game communication since HTML is very slow, but I still don't really know where to start on my server. I would appreciate reading material or guidelines on where to start, what architecture should the game server have and maybe some suggestions on frameworks that could help me getting the client-server communication. I've looked into JNAG but I have no experience with this kind of thing, so I can't really tell if it is a solid and good messaging layer. Any help is appreciated... Thanks ! EDIT: Just a little more information about the game. It is intended to be a very complex game with several functionalities, making some functionalities a "program" inside the program. It is not an usual game, like FPS or RPG but I intend on having a lot of users using these many different "programs" inside the game. If I wasn't clear enough, I'd really appreciate people that have already developed games with java client/server architecture, how they communicated, any frameworks, apis, messaging systems, etc. It is not a question of lack of knowledge of language, more a question for advice, so I don't end up creating something that works, but in the later stages will have to be rewriten for any kind of limiting reason. PS: sorry if my english is not perfect...

  Read the article

• Why would Java app make RPC call to itself?

  - by amphibient

  I am working with a multithreaded homegrown multi-module app in my new job. We use the the Thrift protocol to communicate RPC calls between different stand-alone applications in a distributed system. One of them listens on multiple ports and I just noticed that it actually makes an RPC call to itself from one thread invoked from one socket it listens to (web service call) to another port within the same app. I verified that it could accomplish the same thing if it just went and directly called the method that the remote procedure ultimately invokes as it is all within the same application, same JVM. To make it even more mysterious, the call is completely synchronous, i.e. no callbacks involved. The first thread totally sits and waits until it makes a call across the wire to itself and comes back. Now, I am perplexed why anybody would do it this way. It seems like calling somebody on the phone that sits in the same room as you do. Can anybody provide an explanation why the developer before me would come up with the above mentioned model? Maybe there is a reason and I am missing something.

  Read the article

• How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

  - by MoLE

  I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

  Read the article

• How much overhead is there in persistent connections?

  - by nynex

  Ok so I'm musing over a little side project I want to start. Essentially its a multi-session web based FTP client. Multi-session in that you can log into several FTP servers at the same time and perform operations like moving a file from one FTP server to another. I'm doing this mainly to brush up on the new webdev technologies, particularly websockets. I'm using node.js + socket.io to keep a persistent bi-directional connection between the web browser and the web server. The web server will also have persistent connections to each FTP server the user has logged into. So if there are 100 concurrent users each logged into 5 ftp accounts, the web server will have 100 websocket connections + 500 ftp connections. Is servicing 600 connections a lot? I know it depends on the hardware resources of the server but is something like this doable on a budget? Are there more efficient means of doing something like this? I know its unlikely that this project will really get popular but I want it to scale well regardless. Thanks for any help, I've still got a lot to learn.

  Read the article

• not being able to access any sudo function on my pc

  - by explorex

  Hi, I am not being to access any functions in my desktop and I don't have an OS besides Ubuntu 10.04 Lucid Linux and I am new to ubuntu. I think I rebooted my computer thinking that Google Chrome crashed. I opened Google Chrome but it showed opening message but never opened so I restarted my computer. and when my system was loading ('i was playing with keyboard dont know what I typed') and when by ubutnu loaded, I was unable to access anything some of characteristics are listed below I cannot hear any sound I cannot access wired ethernet connection on the right corner where I usually enable to access interne and I have no internet. There is no local apache server either. when ever I try to start apacer I get setuid must be root or something. When I type sudo then I get message setuid must be root. I cannot access orther external storage devices like pendrive and portable hard drive and cannot mount my other drives with FAT32 filesystem. When I try to start my apache webserver with out typing sudo then I get message cannnot open socket or something like it. EDIT:: i remember also doing command chown -R www-data / earlier and got error message EDIT:: and i cannot shutdown my computer, it only logs off

  Read the article

• Pipe an infinite stream to internal loop?

  - by Sh3ljohn

  I've seen a lot of things about redirecting stdout to a TCP socket, but no real example of how to do it in practice, specifically when the output stream generated by the first "command" never ends. To talk about something concrete, let's take programs like servers that typically output their log endlessly to stdout (well, as long as they run). If you redirect the output to a log file on the disk, then this file is always open (therefore not readable by others?) and grows infinitely, which eventually is going to cause problems. This might be a nood question, but I don't know what it does or how to do it so. How to redirect the output of a command to the internal loop? I want to make sure that data is sent EVERY time something is written to stdout, and that the pipe won't wait for the command to end (never happens ideally!). Is that right? If 2 is true, is there a buffer system to send chunks of data once it reaches a certain size only? Could you give me concrete command line examples to do the above? Thanks in advance

  Read the article

• Ubuntu 12.04 LTX Install Problems (See post for system build details.)

  - by Lokitez

  This is my first ever attempt at working with Ubuntu. I have only ever installed Windows in the past and that may be the problem. I purchased all new hardware this week and I would really like to give Ubuntu a chance (especially since I don't want to buy another Windows license). First, the hardware: AMD FX-8150 Zambezi 3.6GHz Socket AM3+ 125W Eight-Core Desktop Processor ASUS Crosshair V Formula AM3+ AMD 990FX SATA 6Gb/s USB 3.0 ATX AMD Gaming Motherboard SAMSUNG 830 Series MZ-7PC128D/AM 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) - This is my intended boot drive. Western Digital VelociRaptor WD5000HHTZ 500GB 10000 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive - This is a backup drive that I have installed Windows Vista on until I can get Ubuntu to work. G.SKILL Ripjaws X Series 16GB (2 x 8GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 I have downloaded and tried to install both Ubuntu 64 bit and Kubuntu 64 bit (both 12.04). Both will always fail to copy a file during install or otherwise lockup during install to the SSD. I have burned two copies of the Ubuntu 12.04 and had the install fail with both. I have installed Vista onto the HDD. Is it possible to mount the Ubuntu file into

  Read the article

• Information I need to know as a Java Developer [on hold]

  - by Woy

  I'm a java developer. I'm trying to get more knowledge to become a better programmer. I've listed a number of technologies to learn. Instead of what I've listed, what technologies would you suggest to learn as well for a Junior Java Developer? I realize, there's a lot of things to study. Java: - how a garbage collector works - resource management - network programming - TCP/IP HTTP - transactions, - consistency: interfaces, classes collections, hash codes, algorithms, comp. complexity concurrent programming: synchronizing, semafores steam management metability: thread-safety byte code manipulations, reflections, Aspect-Oriented Programming as base to understand frameworks such as Spring etc. Web stack: servlets, filters, socket programming Libraries: JDK, GWT, Apache Commons, Joda-Time, Dependency Injections: Spring, Nano Tools: IDE: very good knowledge - debugger - profiler - web analyzers: Wireshark, firebugs - unit testing SQL/Databases: Basics SELECTing columns from a table Aggregates Part 1: COUNT, SUM, MAX/MIN Aggregates Part 2: DISTINCT, GROUP BY, HAVING + Intermediate JOINs, ANSI-89 and ANSI-92 syntax + UNION vs UNION ALL x NULL handling: COALESCE & Native NULL handling Subqueries: IN, EXISTS, and inline views Subqueries: Correlated ITH syntax: Subquery Factoring/CTE Views Advanced Topics Functions, Stored Procedures, Packages Pivoting data: CASE & PIVOT syntax Hierarchical Queries Cursors: Implicit and Explicit Triggers Dynamic SQL Materialized Views Query Optimization: Indexes Query Optimization: Explain Plans Query Optimization: Profiling Data Modelling: Normal Forms, 1 through 3 Data Modelling: Primary & Foreign Keys Data Modelling: Table Constraints Data Modelling: Link/Corrollary Tables Full Text Searching XML Isolation Levels Entity Relationship Diagrams (ERDs), Logical and Physical Transactions: COMMIT, ROLLBACK, Error Handling

  Read the article

• How do I list all the relation variables and debug them interactively?

  - by mfisch

  I'm writing a charm that requires a mysql database, I found from looking at other charms that this (below) is how I get the info about the database: user=`relation-get user` password=`relation-get password` mysqlhost=`relation-get private-address` But I just found that from reading the wordpress charm example, is there a way to show all the relation variables that I can use? Also, while debugging my db-relation-changed script, I wanted to ssh into my host and interactively run those commands, for example relation-get user, but it didn't work. I resorted to having to restart everything and use juju log to print them out. This wasted a lot of time. Is there a way to print out these relations, either from my dev box or from the instance running my charm? (Below is what happens when I tried to interactively run relation-get): ubuntu@mfisch-local-tracks-0:~$ relation-get user usage: relation-get [-h] [-o OUTPUT] [-s SOCKET] [--client-id CLIENT_ID] [--format FORMAT] [--log-file FILE] [--log-level CRITICAL|DEBUG|INFO|ERROR|WARNING] [-r RELATION ID] [settings_name] [unit_name] No JUJU_AGENT_SOCKET/-s option found I tried juju debug-hooks tracks/0 -e local, that dropped me into a shell and relation-get still failed.

  Read the article

• What packages are safe to uninstall to reduce installation size?

  - by mathematician1975

  This question is similar to a previous question I asked How can I turn my desktop Ubuntu 8.04 into a command line only install?. I was wondering if anyone can recommend any other bulky packages from the standard 8.04 installation that can reduce the size on disk of my installation. All I really require is socket functionality, g++ and gcc, some kind of text editor and SSH client and server. Things that I don't require are things like media players, audio packages, and the more "superficial" kind of desktop niceties. Is there anything particularly large in a standard install that is safe for me to remove without compromising my requirements above? I am a bit apprehensive about trying to uninstall items and I am not totally confident about removal of particular things having a negative effect on the functionality of any other things I might need (an example is would it be safe for me to remove everything to do with Perl, or does the system/kernel/other processes require this) ??? Basically I would like to be left with the kind of items that would have been installed in the CLI version of 8.04 (had the alternative iso image not been faulty). Any help/suggestions would be gratefully received.

  Read the article

< Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >