Search Results

Search found 8416 results on 337 pages for 'stop'.

Page 160/337 | < Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >

  • I can't externally access my home server's wordpress website

    - by piratepartypumpkin
    Basically, I can access everything just fine using 127.0.0.1, but if I use my external IP (123.123.123.123), I get page not found. My router is port forwarding HTTP port 80 to port 8080 on my servers internal IP address. In other words: (Application: HTTP | Start: 80 | End: 8080 | Protocol: Both | IP Address 192.168.0.101 | Enable [YES]) I know it's forwarding properly, because when I stop port forwarding, I can access my router page by using my external IP. My virtual hosts file is: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /opt/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> and my httpd.conf file is: Listen 80 Servername localhost:80 DocumentRoot "/opt/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/opt/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

    Read the article

  • Why would only the cpu fan not spin and no video displayed?

    - by Patrick
    I just built a new computer and when I first powered it on I got a continuous beeping which according to the manual means a power failure. After moving the voltage switch to the left a little I was able to get the beeping to stop. Even after the stopping though the CPU fan doesn't spin, and there is no display on the monitor. All the other fans and lights come on in the computer though, the DVD drive is working and ejects the tray, and the hard drive sounds like it spins up. Has anyone seen this before and know what is wrong or what has failed?

    Read the article

  • MaxClients in apache. How to know the size of my proccess?

    - by Larry
    From http://httpd.apache.org/docs/2.2/misc/perf-tuning.html The single biggest hardware issue affecting webserver performance is RAM. A webserver should never ever have to swap, as swapping increases the latency of each request beyond a point that users consider "fast enough". This causes users to hit stop and reload, further increasing the load. You can, and should, control the MaxClients setting so that your server does not spawn so many children it starts swapping. This procedure for doing this is simple: determine the size of your average Apache process, by looking at your process list via a tool such as top, and divide this into your total available memory, leaving some room for other processes. The main issue is that I can't understand how to know the size, because, well i have the size of httpd on no more of 3888 But, if we need to determine the number for MaxClients, and I have 4GB of RAM, so I get: 972, so I should use like 900 in the MaxClients?

    Read the article

  • Shell Script Launching Child Processes

    - by Matt James
    Disclaimer: I'm totally new to shell scripting, but have quite a bit of experience in other languages like PHP and Obj-C. I'm writing my first daemon script. Here are the goals: I want it to run in the background I want it to be triggered by an init.d script that includes start/stop/restart commands I want each process in a loop to trigger its own subprocess. When the parent process kicked off by the init.d script is killed, I want the subprocesses to die as well. Essentially, I'm looking for the same kind of behavior that appears to be very common among software like apache, spamd, dovecot, etc. But, based on my research, I haven't found a single, simple answer as to how this kind of thing is achieved. Any help is greatly appreciated.

    Read the article

  • Ubuntu server failing daily

    - by deanvz
    Symptoms: Server becomes unresponsive - Increase in load, all services stop Loss of connectivity - Ping/SSH Flush MySQL hosts after reboot - As MySQL refuses new connections Intermittent Apache crashes Generally happens early morning hours - 2 days of the week are however excluded Changes made: Updated the OS - to Ubuntu 10.04.4 LTS Not sure if the MySQL server was also updated in the process Current MySQL version - mysql Ver 14.14 Distrib 5.1.63, for debian-linux-gnu (x86_64) using readline 6.1 Updated Plesk from 10.4.4 Update #47 to 11.0.9 Update #23 Rebooted on almost daily basis All crons stopped for the times corresponding to the server crashes Created a MySQL log to monitor the lock times on queries Possible causes: Failing hardware Incorrect software configuration (MySQL, Apache etc) Responsibilities: Small webserver Runs our billing system - WHMCS Responsible for CRONs Bulk-email solution - No delivery times coincide with server crashes Proposed solutions: Move machine over to VM Format and restore the Plesk server backup and take it from there? Side notes: Seems to be a general Apache failure across all our linux servers - Intermittent problem Are we doing something fundamentally wrong in the Apache config? (I understand that this is a secondary question, just making sure that it isnt possibly holding any relevance)

    Read the article

  • kill process but fail

    - by Tim
    Hi, I am running a bash script as a background job. The bash script calls a time-consuming executable. If I am not wrong, the running of the bash script is the parent process and the running of the executable is the child process. I now want to stop the whole running by killing the parent process which is the background job kill -9 $(jobs -p) The terminal shows that the running of the bash script is killed. But the running of the executable still hangs on the output of top. I just wonder how to also kill the child process? Thanks and regards!

    Read the article

  • Digital Blue Digital Movie Creator 3.0 driver

    - by user27977
    I'm having a complete 'mare of a time trying to use my schools Digital Blue cameras. We've got the model 3 ones, but can't find the driver disc and using the Windows Hardware Installation Wizard gets me no where! Can you help me to find the driver? When I've used it at my old school it had a piece of software called the Digital Movie Creator, which I've heard you can use to make stop-motion films, which is what I want to do! This is what it looks like http://www.amazon.co.uk/Digital-Movie-Creator-1GB-Card/dp/B000LP30LA/ref=sr_1_2?ie=UTF8&s=software&qid=1265928833&sr=1-2

    Read the article

  • pecl_http extension not loading

    - by Tegan Snyder
    For some reason pecl_http extension is not showing up in my test.php file with contains: <?php phpinfo(); ?> I just installed pecl_http using: pecl install pecl_http The install was successful and I verified it by running: pecl list Installed packages, channel pecl.php.net: ========================================= Package Version State mongo 1.2.10 stable pecl_http 1.7.4 stable I then located my php.ini file using: php -i | grep 'Configuration File' Configuration File (php.ini) Path => /etc/php5/cli Loaded Configuration File => /etc/php5/cli/php.ini I edited it in vim and added: extension=http.so Finally I restarted Nginx and PHP-FastCGI: /etc/init.d/nginx restart /etc/init.d/php-fastcgi stop /etc/init.d/php-fastcgi start My PHP extension_dir is : /usr/lib/php5/20090626 I verified that "http.so" is located in that directory. Any ideas why it's not loading? My machine is running a Ubuntu 10.04 LTS 64bit Profile on Linode. The only other extensions I have installed are New Relic and Mongo. Thanks!

    Read the article

  • Pause/play AJAX on particular tabs in firefox

    - by bguiz
    Hi, I want to know if there is some method to disable AJAX on particular tabs within Firefox and re-enable them later. My concern is that I have metered bandwidth, and I need to conserve my usage. But I also like to leave several Gmail tabs open in the background. It would be great if I could just hit a "Pause AJAX" button, to stop the contents of that tab from sending or receiving anything, and then later on hit a "Play" button when I want it to start doing its thing again. Any suggestions?

    Read the article

  • Volume key occassionally changes relative volume in mixer

    - by bobobobo
    I find this a bit of a nuisance but I usually use the "volume up/down" key on my Microsoft ergo 4000 to change the volume of my system. The problem I'm experiencing is every so often, the volume of Winamp goes way down relative to the other apps in the mixer: So I don't always notice this right away, suddenly I can't hear Brandy warbling. And that makes me sad. Or mad. Or both. But it's a nuisance - is there a special key combination I need to avoid pressing to stop the mixer from imbalancing? Is there a way to disable this "app specific" mixer, because it is completely useless to me.

    Read the article

  • Dlink DIR-615 suddenly stops working - Orange internet light

    - by zm15
    I unplugged my Dlink DIR-615 router last night from the wall due to a storm rolling in. I've done this countless times, no problem. However, when I went to plug it in and use the internet today, nothing. Check everything, cycled everything. Hard reset the router, nothing. The little globe on the front is red/orange, and it should be green. Windows gives me an error of a "DNS Issue", and the internet works when connected directly to the modem. How can I fix this issue? Why would it suddenly stop working?

    Read the article

  • Sar data not collected for 10 minutes

    - by Ichorus
    We have a RedHat server whose only job is to run a JBoss server. Monitors said that memory usage spiked (we have the JVM limited to far less than the total memory on the system) and JBoss crashed. We restarted and everything seems ok now. Odd thing is that sar data for 10 min leading up to the crash is simply not there. Load average got up to the 50s. I have seen severely busy systems (350+ Load Average) still collect sar data. Does anyone have any idea what could cause sar to stop collecting data?

    Read the article

  • XP Computer won't start (Missing/Corrupt 'System' file) - recently added new hard drive

    - by qwerty2
    Hi all, Pulling my hair out here. I recently replaced my D: 1TB drive (not a system drive) with a new 1.5TB drive. I loaded Windows XP, formatted the new drive and it was showing as working fine, alongside my C: windows system drive. I restart my machine and all of a sudden, Windows doesn't load and instead I get: "Windows could not start beause the following file is missing or corrupt" \WINDOWS\SYSTEM32\CONFIG\SYSTEM I don't have the original XP installation CD, although I do have another copy of XP, when I try and boot to it, I get the blue 'STOP' screen after it attempts to load the setup utlity for about a minute. Can someone please help? When I set up my new hard drive as a primary partition did this someone screw up my C: hard drive? Did it perhaps unmount it somehow? Any help would be fantastic. Thanks

    Read the article

  • XP Computer won't start (Missing/Corrupt 'System' file) - recently added new hard drive

    - by qwerty2
    Hi all, Pulling my hair out here. I recently replaced my D: 1TB drive (not a system drive) with a new 1.5TB drive. I loaded Windows XP, formatted the new drive and it was showing as working fine, alongside my C: windows system drive. I restart my machine and all of a sudden, Windows doesn't load and instead I get: "Windows could not start beause the following file is missing or corrupt" \WINDOWS\SYSTEM32\CONFIG\SYSTEM I don't have the original XP installation CD, although I do have another copy of XP, when I try and boot to it, I get the blue 'STOP' screen after it attempts to load the setup utlity for about a minute. Can someone please help? When I set up my new hard drive as a primary partition did this someone screw up my C: hard drive? Did it perhaps unmount it somehow? Any help would be fantastic. Thanks

    Read the article

  • Folder permissions when using /etc/skel and pam

    - by rothgar
    I have a Red Hat 5.8 server that is bound to active directory and users are authenticated via active directory when they log in via sftp. User home folders are created during login using /etc/pam.d/system-auth. The specific line that creates the home folder is session optional pam_mkhomedir.so skel=/etc/skel/ umask=0066 This correctly gives home folders 711 permissions so no one else can read their directories. The problem is, the pam_mkhomedir.so also modifies permissions on all folders/files inside the /etc/skel folder which I don't want. There is a public_html folder (for apache) which needs to have 755 permissions so users can create web pages. Is there a way for me to either a) stop pam_mkhomedir.so from recursively changing all the file permissions or b) create a script that creates the public_html folder after skel is copied and to set the correct permissions?

    Read the article

  • Private cloud solution [Eucalyptus,OpenStack, Nimbus] for Java deployments [Glassfish, Tomcat]

    - by Tadas D.
    I am interested in a way to have private cloud which would host Glassfish (or Tomcat) server. Which option from Eucalyptus, Openstack or Nimbus would be best to deploy java applications on it? Or maybe there is something other and I am looking wrong at the problem? The way I imagine this, that I should have some shared storage that I could expand by introducing new nodes to this cluster and have easy management for glassfish instances: something like virtual machines images that I can start and stop on demand and that image is shared among nodes. I don't need concrete step-by-step solution here but guidelines how this should be done are very welcome.

    Read the article

  • Difficulty in running Tomcat v7.0 with Eclipse Juno

    - by user1673718
    I get the following error when I run my JSP file in Eclipse-Juno with Tomcat v7: 'starting Tomcat v7.0 server at localhost' has encountered a problem. Port 8080 required by Tomcat v7.0 server at localhost is already in use. The server may already be running in another process, or a system process may be using the port. To start this server you will need to stop the other process or change the port number(s). I have Oracle 10g installed in my System. When I type "http://localhost:8080" it opens the Oracle 10g license agreement so I think Oracle 10g is already running in that port. To change the port of Tomcat I tried Google, which said to change the port in the "C:\Program Files\Apache Software Foundation\Apache Tomcat 7.0.14\conf\httpd.conf" file But at "C:\Program Files\Apache Software Foundation\Apache Tomcat 7.0.14\conf" there was no httpd.conf file. I only have "catalina.policy,catalina.properties,context,logging.properties,server,tomcat-users,web" files in that conf folder. I use windows XP.

    Read the article

  • Cursor moves when left or right clicking on trackpad

    - by n00b
    I'm on an acer aspire v5-572p. When I am using the touchpad, and I left or right click something, the cursor moves every time by a couple pixels because unfortunately the clicking area, is also a touch area. I've tried switching to the synaptics mouse drivers provided on the Acer driver website, but the same problem exist. I have researched this problem and there is a fix for this issue in Ubuntu, but I am running Windows 8.1 x64. The problem also existed when I was on 8.0 How do I stop the cursor from moving on a click?

    Read the article

  • How to prevent hard drive from spinning down Windows 7?

    - by JL.
    I had a Western Digital External 1TB drive, which I was accessing via USB. I decided one day, that I would prefer to mount the HDD in my case, and access it via SATA interface. So I took it apart, and the actual mounting was a breeze. The only thing is, I think the device has some default power saving features, which means the device tends to stop spinning when idle for (x) amount of time. This creates delays when I am accessing the HDD. Is there anyway I can turn off these power saving features for this HDD?

    Read the article

  • Ubuntu 12.04 Samba File Server timeout on large file

    - by phileaton
    I am a beginner with servers. I checked the error logs for Samba and it appears that Samba is timing out when I transfer large files. I can successfully add pdfs for instance to my file server. However, I tried to add a large 1.2gb video file and it did not succeed. This is the error in the log: smbd/process.c:244(read_packet_remainder) read_fd_with_timeout failed for client 0.0.0.0 read error = NT_STATUS_CONNECT$ Is there a way I can stop it from timing out? Any pointers would be great! Thanks!

    Read the article

  • How do I disable Tomcat? [closed]

    - by Dave King Popeye Mason
    Possible Duplicate: How to disable Tomcat on linux? According to my server host, something called Tomcat is hogging all my resources and slowing down the server. As far as I'm aware I'm not using it as the only thing running on the server is Plesk and a few Wordpress installations. I'm a real dummy at using SSH, I can navigate to folders, change permissions and that's about it. Could somebody explain to me as if I'm a 5 year old how to disable TomCat (and also how to stop it re-enabling on startup)? Thanks!

    Read the article

  • How to block access to websites on a linux box [closed]

    - by user364952
    I'm just curious how many ways people can come up with to block access to a website. I simply intended to block (my own) access to news.ycombinator.com to stop my productivity drain. The first two methods I thought of were editing the hosts file to resolve news.ycombinator.com to 0.0.0.0 or adding a rule to iptables. iptables -A OUTPUT -d news.ycombinator.com -j REJECT Disclaimer: I do realise that the above two methods are easily by-passable. Doesn't help this is my own machine. What other ways does the internet know?

    Read the article

  • How to install Apache 2.4.3 on Ubuntu 12.04

    - by SFox
    I have a clean, fresh OS of Ubuntu 12.04 on my VPS. My goal is to install WordPress. I want to install the latest version of Apache (2.4.3) but I'm encountering two problems. I'm following instructions like this & this. Both produced the same errors. The first I encounter after running "./configure --prefix=/usr/local/apache2 --with-included-apr --with-included-apr-util " the system says "It must specify an install prefix, a build directory, or an apr-config file" The second I encounter immediately afterwards, when I attempt to run make or make install. "No targets specified and no makefile found. stop." I honestly have not been able to find a solution for either, and I'm now looking for some help from the community. Any help would be greatly appreciated.

    Read the article

  • Can a Shadow Copy of SQL 2000 databases files be used as a restore?

    - by Keith Sirmons
    Howdy, I have a SQL 2000 instance (version 8.00.760) that is on a drive that gets regular shadow copies. Can a shadow copy be used to restore the database? It seems possible to stop the SQL service, restore the Data folder from the shadow copy (includes msdb, master, model, temp, and the user databases, then restart the service. Would the files be in a crash consistent case in the worst case? If so, when restarting the service wouldn't it recover as if the power were pulled from the server? Thank you, Keith

    Read the article

  • Remove auto-complete field entries in Google Chrome

    - by NT.
    Is there a way to stop the gmail address field (on the login page) from displaying all the gmail addresses that you have ever typed in it? When logging in with Google Chrome or trying to set up a new account, anything you type which starts with the same letter as the one that you are trying to use currently will show up in the auto-complete field, I don't want that. I understand that this is a convenient feature in some cases, but the thing is--I know this shouldn't've happened, but it has actually happened more than once--I sometimes mistyped my password in the Gmail address field right after the address, mistakingly assuming that the prompt had already been moved to the password field, and then hit "Enter" without looking first. The next time I tried to enter my Gmail address, it popped up the address followed by my password as one of the entries on the list of email addresses that shows up, and I couldn't get rid of the entry. Is there a way to remove these?

    Read the article

< Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >