Search Results

Search found 5136 results on 206 pages for 'aviation week'.

Page 161/206 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• Why are ISP's installing routers on my site when the feed is a form of ethernet already?

  - by Cosmin Prund

  I'm connected to 3 ISP's right now. Two of them already have routers at my site, the third one announced me "they need to install some equipment" when I requested BGP session. I can only assume they need to install a Router, since that connection is now working fine, using the usual /30 net block for the connection, and the "last-mile" solution is not going to change since they only installed it last week and the BGP was in the contract from the beginning. I simply don't understand this: the "feed" is already a form of ethernet. Even those they're using different technologies for the last mile, they're all entering the ISP router using an RJ45 WAN port. I assume the ISP router does something really important that can't be done by the Big Router on the other end of the connection. It must also be something that can hurt them if miss-configured, since they don't trust us (the client) to do the stuff on our router. And I'm not talking cheap throw-away routers here: One of the routers is Cisco 2800. Edit to add network details: I'm connected to 3 ISP's, two over Radio links, one over Fiber Optic. One of the radio links is going to get dropped and the other radio link will be turned into fiber sometime next year. The fiber is 20 Mbit, radio 1 is 40 Mbit and radio 2 is 2 Mbit. I've got a /24 of provider independent address space. I'm not doing out-of-the ordinary stuff with my network, I'm overly connected because my network needs to be "up" all the time.

  Read the article

• Intermittently uncommunicative subnets

  - by mhd

  Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

  Read the article

• Thunderbird 11.0.1 and Lightning 1.3: How do I propose a different time for a meeting?

  - by seaao

  This all happens on my x64 Linux workstation btw. tl;dr: My colleague invited some people and me for a meeting. The meeting was scheduled a week to late. I -wrongfully- accepted. How do I propose a new time? To explain a bit more in detail: I received a meeting request in my mailbox. Thunderbird is so nice to let me accept or reject it, and after I click the button to accept, it is directly added to my calendar. But when I double click on the meeting to edit it, I get a function-wise scaled-down version of the meeting: The only settings I can alter are whether I want reminders, and if I go at all. Trying to drag it to another day doesn't work either: My calendar behaves like read-only (which it isn't btw). There are several questions (without answer...) to be found on Stack Overflow and on the Thunderbird knowledge base about using lightning. But I get the idea that I'm one of the few who won't comply with the team even before the meeting is started. My googling revealed no bugs or feature requests in the direction I'm thinking. A link to an explanation how to achieve this, or another perspective about how to reach the desired goal (meeting with my colleagues and me) would be mostly welcome!

  Read the article

• Windows 7 DVD doesn't boot up, neither does USB. :'(

  - by Manan Shah

  My problem is that i'm not able to install windows 7. Been trying to install this since past 1 week. The methods i've tried are: I have a windows 7 bootable DVD which doesnt boot up. (I've set BIOS to boot from DVD ROM first but it just won't boot from the DVD). Tried to install Windows 7 from the same DVD to a friend's PC and it worked. So the DVD has no issues. I tried to run 'Setup.exe' from within the DVD. The two options pop-up 'Check compatibility' and 'Install now'. On clicking install now, after sometime, an error is encountered with the message 'Windows was unable to create a required installation folder' error code:0x8007000D. I am running Windows XP Professional and there's only one user on the PC which is the Admin, so i do not know why is the setup not getting permissions. I've also uninstalled my antivirus, CD burning software, disabled firewall and disconnected all other devices, but its still the same. I tried to install it from a USB device by making it bootable but that too doesnt work. (Yes the mobo supports booting from the USB). The problem is that XP does not recognize a 'USB' device on boot. Rather it shows this USB stick as a removable 'Hard Drive'. Furthermore, i changed the order of Hard Drive boot to boot from this removable Hard Drive first, it still boots my existing OS. Is there anything else that can be done? Any help would be greatly appreciated. :) Please ask if any other information is required, this post is becomimg increasingly long to add any other details. PS: I want to dual boot windows 7 with my existing XP, but that would be after i manage to run the windows 7 setup in the first place. PPS: Please bare with any 'not-so-technical' terms, i am a beginner with this. Again, thank you for taking the time and trying to help, really appreciate it. :)

  Read the article

• ipv6 reverse DNS delegation

  - by user1709492

  I currently have 2001:1973:2303::/48 assigned to me and i'll be assigning /64's to customer's I'd like to have 1 zonefile for the /48 where i can essentially point / redirect query to different nameservers. Example ( Desired effect ) 2001:1973:2303:1234::/64 -> ns1.example.com, ns2.example.com 2001:1973:2303:2345::/64 -> ns99.example2.com, ns100.example2.com 2001:1973:2303:4321::/64 -> ns1.cust1.com, ns2.cust1.com Current /48 zonefile $TTL 3h $ORIGIN 3.0.3.2.3.7.9.1.1.0.0.2.ip6.arpa. @ IN SOA ns3.example.ca. ns4.example.ca. ( 2011071030 ; serial 3h ; refresh after 3 hours 1h ; retry after 1 hour 1w ; expire after 1 week 1h ) ; negative caching TTL of 1 hour IN NS ns3.example.ca. IN NS ns4.example.ca. 1234 IN NS ns1.example.com. NS ns2.example.com. 2345 IN NS ns99.example2.com. NS ns100.example2.com. 4321 IN NS ns1.cust1.com. NS ns2.cust1.com. Where am i going wrong ? My request seems simple to me atleast. To put it in terms of firewalling i want to redirect traffic client queries 2001:1973:2303:4321::1 - ns3.example.ca sees the request and redirects the query to ns1.cust1.com - ns1.cust1.com answers the query with omg.itworks.ca ( provided ns1.cust1.com is properly configured.

  Read the article

• Windows7 corrupted profile - prevention exists?

  - by Radek

  I have dedicated Windows7 (not on domain) virtual machine for overnight automation testing. Some commands (mySQLdump, tscon.exe) must be run under administrator account. Last week administrator account's profile was corrupted. I fixed it by renaming it in the registry and logging in as administrator. And today it is corrupted again. I use administrator account only to run above commands via runas. Also the computer is restarted via cmd - shutdown command - quite often. Especially every night before automation testing starts. I checked the comp for viruses - did full scan using avast although I believed that the comp is clean. Any idea how to prevent the profile to get corrupted again? update So the first log entry in event log is today from 1.15am and one of my scripts ran runas command as administrator exactly at 1.15am. It was second time that runas war executed though after the testing started. The same happened second day in a row. Before the testing starts I need to copy one file that is locked. So I run handle.exe from runas to unlock it. That is what I think causing the profile to get corrupted. I am not able to reproduce it by myself. The message from event viewer is Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile. DETAIL – The process cannot access the file because it is being used by another process.

  Read the article

• Windows Server 08 R2 file share File locking, OSX clients

  - by Keith Loughnane

  I've spent the last two weeks banging my head against this wall. I think I'm starting to understand the problem though. I manage a design company and they have 5 macs (OSX 10.5/.6/.7) connected over SMB to a Windows 2008 R2 file server, another machine functions as Domain Controller (that might not matter). All the macs can connect ok, no issues finding the server or logging in. For the most part things are ok. The problem is files locking up. I thought it was a permissions issue at first but it seems to be file locking. The users open a file; .ind, .pdf etc the file opens, the software reads it and closes it. That's fine, but the folder above the folder locks, it can't be moved and it can't be renamed. Eg: /Working/Project01/Imagefiles/image.pdf /Finished/ The user opens image.pdf, closes it and wants to move the whole Project01 folder into Finished. It gives a username/pass dialogue and then does nothing, no error, or just does nothing. Trying to rename gives a dialogue that says you don't have permission. It looks like it's looking for permission locally, which is why I spent about a week looking at that. Eventually I found that Finder on the macs seems to be keeping the folders open. I can work around it by Killing finder, remounting the shared drive or closing the file through the server manager but this just proves the theory it's not a solution. Has anyone dealt with this problem?

  Read the article

• Grub error 18, gparted not showing anything

  - by Montecristo

  Some week ago I started having some problems with my pc, sometimes it just freezed not allowing me to do anything. I had to turn it off and on and sometimes do it a couple of time even at startup. Now it does not start at all, grub is giving me error 18. I have found that a solution is to create a bootable partition in the first sector of the disk. gparted does not recognize any partition, the window in which there would be my partitions is empty. sudo fdisk -l does not output anything. If I type sudo mount /dev/sda and then tab tab to autocomplete these are the devices coming out: sda sda1 sda2 sda5. If I launch sudo mount -t ext3 /dev/sda1 disk I get the following error: mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so dmesg outputs [ 1831.974847] EXT3-fs: unable to read superblock Do you know how to solve this issue? I'm not completely sure this is a software problem, should I try with a new hard disk?

  Read the article

• Deleted printers keeps coming back - and multiply

  - by MojoDK

  My users are on 2012 R2 RDS Session Host servers. I've used "Deploy Printers" (from Print Manager) to deploy 4 printers. The last week, I've had a lot of problems where users can't print. If I deleted the printer and added it again, they could print just fine. Now I've removed all printer deploying from GPO - and I have no printers in any login scripts. I did a gpupdate /force, but all the 4 printers are now listed 3 times... If I delete the printers and log off and back on, all the printers are popping up again. Sigh! This is driving me nuts. This script doesn't show any of the "SVFREJA" printers... Set objWMIService = GetObject("winmgmts:\\.\root\cimv2") Set colPrinters = objWMIService.ExecQuery ("Select * From Win32_Printer") If colPrinters.Count <> 0 Then 'If there are some network printers Dim s s = "" For Each objPrinterInstalled In colPrinters ' For each network printer s = s + objPrinterInstalled.Name + chr(13) Next msgbox s End if It gives me this result... (sry for the big picture) My problem is not with the "redirected" printers, my problem is that I have several printers with the same name (on SVFREJA) and I can't get rid of them. Any idea why I can't get rid of the "ophaned" printers??

  Read the article

• Can MySQL use multiple data directories on different physical storage devices

  - by sirlark

  I am running MySQL with its data dir on a 128Gb SSD. I am dealing with large datasets (~20Gb) that are loaded and processed weekly, each stored in a separate DB for the purposes of time point comparisons. Putting all the data into a single database in unfeasible because the performance on such large databases is already a problem. However, I cannot keep more than 6 datasets on the SSD at a time. Right now I am manually dumping the oldest to much larger 2Tb spinning disk every week, and dropping the database to make space for the new one. But if I need one of the 'archived' databases (a semi regular occurrence) I have to drop a current one (after dumping), reload it, do what I need to, then reverse the results. Is there a way to configure MySQL to use multiple data directories, say one on the SSD and one on the 2Tb spinning disk, and 'merge' them transparently? If I could do this, then archiving would no longer mean "moved out of the database entirely", but instead would mean "moved onto the slow physical device". The time taken to do my queries on a spinning disk would be less than that taken to completely dump, drop, load, drop, reload two entire databases, so this is a win. I thought of using something like unionfs but I can't think of a way to control which database gets stored on which physical drive, because it works by merging on a directory level (from what I understand) so I'm still stuck with using multiple directories. Any help appreciated, thanks in advance

  Read the article

• Missing drive space in Server 2003

  - by Tim Brigham

  I have two drives used for SQL backups which for the last week have been acting strange - the free space indicated by windows is far off from what windirstat, etc indicates. There should only be about 60 GB of drive space used and there is about 160. This would match the utilization if the two last backup files were still residing on disk. SQL server is 2000, OS Server 2003 x64. Running on a VMware 5.0 cluster. OSSEC and McAfee for this system shows clean. My current plan is to temporarily attach one of these drives this drive to another VM for analysis. Is there anything more I should be looking at? There were a lot of pages on the net when I was looking for documentation on this issue but I haven't found this case described. EDIT: Unfortunately even a full reboot did not clear this behavior. I also used process explorer to look for open file handles. No dice.

  Read the article

• How to view / enumerate / obtain a list of all effective rights / permissions on an Active Directory object?

  - by Laura

  I am new to Server Fault and was hoping to find an answer to a question that I have been struggling with for the past week or so. I have been recently asked by my management to furnish a list of all the effective rights / permissions delegated on the Active Directory object for our Domain Admins group. I initially figured I'd use the Effective Permissions Tab in Active Directory Users and Computers but had two problems with it. The first was that it doesn't seem very accurate and the second was that it requires me to enter the name of a specific user, and it only shows me what it figures are effective permissions for that user. Now, we have more than a 1000 users in our environment so there's no way I can possibly enter 1000 user names one by one. Plus, there is no way to export that information either. I also looked at dsacls from MS but it doesn't do effective permissions. Someone pointed me to a tool called ADUCAdmin but that seems to falsely claim to do effective permissions. Could someone kindly help me find a way to obtain this listing? Basically, I need to generate a list of all the modify effective permissions granted on the Domain Admins group object along with the list of all the admins to which these permissions are granted. In case it helps, I don't need a fancy listing - simple text / CSV output would be enough I would be grateful for any assistance since this is time and security sensitive for us.

  Read the article

• keyboard intermittently stops working, even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash a couple of the ctrl+alt+windows type keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu, but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) *Unplugging & reconnecting keyboard does NOT fix it. *Connecting a different keyboard does NOT fix it. That one won't work, either. *Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. *Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears, they keyboard won't work, and neither will the icon to pull up the on-screen keyboard. Otherwise my mouse can click around just fine. I can only log onto a non-password protected account. *Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. *Clearing my Chrome browsing data stopped the problem from recurring for a week or so. *I use Avira free antivirus software, and repeated scans turn up nothing fishy. *I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. The only thing I suspect is something in Google Chrome -- I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• Mac OS X in Virtualbox says "You need to restart your computer"

  - by humoeba

  I've been trying to figure out for the past week how to get Snow Leopard reliably running in a VM. Right now I am using VirtualBox, and it runs fine for a while, but every once in a while (happened 3 times in the last few hours) I get the "You need to restart your computer" message. Unfortunately, it hasn't even lasted long enough to finish installing the operating system yet. I first tried VMWare, which was a pain to set up. I got it running ok, operating system installed, with the guest tools. Every once in a while though, it just stops running. I click inside the VM, and there's no mouse. It doesn't respond to keyboard input either. I have to reset the VM to get a response. I'm wondering if this is the same error. This happens with both Workstation and Player. Here is the tutorial I used for VirtualBox: http://www.sysprobs.com/iboot-loader-virtualbox-install-snow-leopard Here's the tutorial I used for VMWare: http://bobhood.wordpress.com/2009/12/18/welcome-to-snow-leopard-mac-os-x-10-6-and-vmware-workstation-7/ I'm using an iso for Mac OS X 10.6.3. I have an HP Pavilion dm4 with an Intel Core i7 M640 running Windows 7; VT is turned on. Using VirtualBox 4.0.4 and VMWare Workstation 7.0.1 and VMWare Player 3.0.1 Does anyone know what might be causing this error or how I can fix it? Thanks.

  Read the article

• Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

  - by tednewk

  I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

  - by camelCase

  I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

  Read the article

• torrent downloads not showing on Squid log

  - by noobroot

  hello, i have just a few months working as sysadmin, hence i still have lots to learn, first thing id like to do is as follows: We have an OpenBSD 4.5 box acting like firewall,dns,cache etc, the box has 2 network cards, one conected directly to the internet and the other to our switch, i used to work with sarg for the log analysis but then changed to the much faster free-sa. I use a daily free-sa report to check the bandwidth usage and report our top 5 bandwidth consumers (3 days a week being #1 and you will be buying the pizzas :D, we are a small company ~20 so we are very familiar). this was working really good until recently, one of us required to download some stuff via torrent (~3GB) and since the pizza rule is active for non-work related downloads, he told me (verified) that his download was indeed work related so i would dismiss that 3GB off his quota, but to my surprise the log didnt showed that 3GB, since his ip consumption was only around 290MB. More recently, since the FIFA world cup started, we know that some of the employees are watching the match's streaming, we know it and we dont care about it since, like already stated, we are a small company so we dont have restrictive policies, we all can chat, watch youtube, download anything we want BUT we are only allowed 300MB a day otherwise you'll get in the top5-pizza-board, anyway, that streaming consumption is also not showing in the free-sa reports. So my question is, why is these data being excluded from the reports? im thinking that the free-sa reports list only certain types of things but im also thinking if are the squid logs the ones that are not erm... logging these conections. Any help, guide, advice or clarification is appreciated.

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• HP EliteBook 8440P - USB ports stop working on docking station

  - by r0ca

  I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

  Read the article

• Openfire: Granular alerts

  - by R.S.

  Our organization has had an Openfire server up and running for about a year now. So far we have used it for messaging in the I.T. Dept and Alerts to all users. We hit a snag this week when one system went down and several notifications were sent out to inform users of progress. Some of the users were Radiologists that do not use the particular system in question and these users found it more of an annoyance than informative. Since that I have been tasked with finding a more granular system for alerts. I am confident that Openfire can handle this and I have just about settled on a way of getting this to work. My idea is to create a half dozen or so users. For example: Staff, Doctor, Assitant and Supervisor. Using spark as our messenger has worked great so far so I would like to stick with that if possible. With that in mind, under advanced login features the resource name can be changed to something unique and non-unique users can log in under the same account, however, when a message is sent to one of these users, the message delivery is inconsistent. Currently I have 4 users under the Assistant user and it seems only 1 of the users receives the messages. Is this scenario even possible? I am avoiding working with the groups in Openfire because the function is atrocious. I could possibly integrate the system into our Active directory but I don’t think that will get us to a workable solution any quicker or more efficiently.

  Read the article

• Diagnose remote desktop freezes in Windows 7 when no BSOD?

  - by Paul Smith

  Okay, I'm getting no joy from Asus or Microsoft on this, so hoping for some clues on how to narrow down the cause. I have very frequent OS freezes, always & only when running Remote Destkop Client (mstsc) in Windows 7 x64. I never have a bluescreen, and there is never a minidump. The display & input just freezes -- no keyboard, no mouse, and sound will just continue the last wavelength if any. So far, I can't find a way to trap the hang given that there's no bluescreen; advanced startup & recovery settings for system failure are "Write an event" checked, "Automatically restart" checked, and "Kernel memory dump". I've updated to the lasted BIOS, and tried a few different graphics drivers, both generic & ATI. I've also tried disabling Aero, and everything about the remote desktop experience (incrementally unchecked every box in the mstsc - options - experience tab), even disabled/unplugged external monitor to make sure it wasn't a dual-monitor issue. My specs are: Asus G73jh notebook 8GB RAM ATI Mobility Radeon HD 5800 Series graphics (recently tried driver versions 8.791.0.0, 8.801.0.0) American Megatrends G73jh.211 BIOS (7/27/2010) Windows 7 Home Premium x64 Windows Memory Diagnostic passed all of the following at least 3 times with no errors: MATS+ INVC LRAND Stride6 WMATS+ WINVC This notebook is better than most at removing heat (laudable vent design), so I'm not inclined to suspect thermal causes (especially since running 1080p video for hours has never caused a freeze, but mstsc does, reliably, within 5 minutes to an hour). This did seem to start happening after a Windows Update, but I've since reverted every patch applied since a week before the first occurrence, with no joy. (And I'd only had the PC for a couple weeks before that, so it could have been chance + less actual time spent remoting at the beginning.) I'm at my wits end, and I bought this laptop primarily as a remote terminal client (go figure, right?) Any ideas on how to identify the cause of this? Thanks!

  Read the article

• How to go about rotating logs which are arbitrary named and placed in deeply nested directories?

  - by Roman Grazhdan

  I have a couple of hosts which are basically a playground for developers. On these hosts, each of them has a directory under /tmp where he is free to do all he wants - store files, write logs etc. Of course, the logs are to be rotated, or else the disc will be 100% full in a week. The files can be plenty, but I've dealt with it with paths like /tmp/[a-e]*/* and so on and lived happily for a while, but as they try new cool stuff on the machine logrotate rules grow ugly and unmanageable, and it's getting more difficult to understand which files hit the glob. Also, logrotate would segfault if asked to rotate a socket. I don't feel like trying to enforce some naming policies in that environment, I think it's going to take quite a lot of time and get people annoyed and still would fail at some point. And I still need to manage the logs, not just rm the dirs at night. So is it a good idea in circumstances like these to write a script which would handle these temporary files? I prefer sticking with standard utilities whenever possible, but here I think logrotate is getting less and less manageable. And probably someone heard of some logrotate alternatives which would work well in such an environment? I don't need emailing logs or some other advanced features, so theoretically some well commented find | xargs would do. P.S. I do have a log aggregator but this stuff is not going to touch my little cute logstash machine.

  Read the article

• Proper Outlook Free/Busy status when working from home

  - by rwmnau

  Our office (pretty large - about 200 people) has recently started part-time telecommuting. It's only one day/week now, but it's already raised some questions about availability, so I wanted to see how the users here, some of whom I'm sure telecommute to a corporate job, how they set their out of office status. Outlook has four statuses, and here's what I (and most others?) take them to mean: Free: I'm available for meetings Busy: I'm in a meeting or otherwise occupied, and unavailable Tentative: Shy away from scheduling over, but I'm available if needed Out of office: I'm on vacation and unavailable. However, I don't travel for work - do people tend to use this status to mean they're remote, but available for a phone call/bridge? As we begin to telecommute, I'll be available by phone for meetings, but not in person - any meeting can have a conference bridge, but some meetings just need to be in person. I'd like to send the right message about my status - people can schedule meetings with me on my telecommute days, but they should expect me to be on a conference bridge when they do. What status do people use? Does "Out of Office" correctly reflect that you're working from home, even though I perceive this to mean that somebody is on vacation? Maybe I'm the only one confused here, but as a company that's never before done telecommuting of any kind, I'm in the dark about standard practices. Thanks for the insight! Though this isn't a technical question directly, I'm hoping it's still applicable to the group and constructive - if it's not, please close it and accept my apology.

  Read the article

• Is there an application to log component temperatures to file?

  - by MrVimes

  I purchased a computer a month or two ago (core i7, 24gb ram, geforce gtx 590, windows 7 ultimate). Within the last week it began to bluescreen regularly. I tried lots of things (check hds, check memory, reinstall windows etc..) but it still bluescreened. At the time my temps were as follows... CPU - aprox 40/50c. GPU - arpox 60 idle, aprox 90 during heavy use. HDDs - aprox 55c after the PC had been on a while. I thought the 55c was ok, but I have since realized it was probably too high and may have been the direct cause of the bluescreening. I've installed a spare fan I had in the front of the PC blowing air in, (so there's airflow from front to back) Since then, obviously, all my temps are down. Especially the HDDs - three of them reach 30c and one has been up to 47c (it is some distance away from the airflow, in one of the 5.25inch drive bays) I haven't had the PC on for as long as it would normally take to bluescreen yet, but If it does I want to know what all the temps were right before the bluescreen. I have tried Everest but it only shows me realtime temps or gives me the ability to create one-off reports. I want something that can record all the temps to a file at 30 seconds intervals. If the computer bluescreens I can load it up again and check the last entry in the file. Side question: Am I right in thinking 55c was far too hot for a HDD? (It might have got higher than that before the bluescreens.. I don't know) Another side question: Is 47c too high? This is actually why I am asking the main question - I am concerned that this one drive that isn't getting the benefit of the extra fan may still cause the computer to bluescreen.

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >