Search Results

Search found 5464 results on 219 pages for 'effect'.

Page 161/219 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• Matched or unmatched drives for RAID arrays?

  - by Will

  Looking around there is conflciting information on this, with some strongly suggesting one or the other. From my understanding the issue with matched drives is that the wear on both drives is more or less the same, so the potential for the second drive failing with or very soon after the first is pretty high. People also claim matched drives give substianatally higher performance however assuming the unmatched drives are more or less the same (eg 2, 1 TB STATA II 7200rpm drives with 32MB cache), would the minor differences between say a Seagate and a Western Digital one (say one has a 128MB/s read rate, and the other a 150MB/s read rate, as well as I guess various other minor differences) actually cause any notable performance loss, ie potentialy worse than two matched 128MB/s drives, or does RAID not really care and give you essentially an optimal solution (eg upto 278MB/s total read speed for RAID 0 and 1) and similar for other RAID with more "unmatched" drives (5 and 1+0 come to mind as possibilities)? Also I couldnt find much info on how this is different on different RAID setups, eg RAID 0 or RAID 1, software or hardware RAID, etc. I'm assuming such things have an effect, and thats it's not all the same for RAID in general?

  Read the article

• Nginx Multiple If Statements Cause Memory Usage to Jump

  - by Justin Kulesza

  We need to block a large number of requests by IP address with nginx. The requests are proxied by a CDN, and so we cannot block with the actual client IP address (it would be the IP address of the CDN, not the actual client). So, we have $http_x_forwarded_for which contains the IP which we need to block for a given request. Similarly, we cannot use IP tables, as blocking the IP address of the proxied client will have no effect. We need to use nginx to block the requested based on the value of $http_x_forwarded_for. Initially, we tried multiple, simple if statements: http://pastie.org/5110910 However, this caused our nginx memory usage to jump considerably. We went from somewhere around a 40MB resident size to over a 200MB resident size. If we changed things up, and created one large regex that matched the necessary IP addresses, memory usage was fairly normal: http://pastie.org/5110923 Keep in mind that we're trying to block many more than 3 or 4 IP addresses... more like 50 to 100, which may be included in several (20+) nginx server configuration blocks. Thoughts? Suggestions? I'm interested both in why memory usage would spike so greatly using multiple if blocks, and also if there are any better ways to achieve our goal.

  Read the article

• Windows Server 2008 IIS7 - page requests randomly hang or timeout

  - by seb835

  I've just installed a fresh copy of Windows Server 2008 x64 with IIS7 and PHP (fast CGI). However, I'm noticing that after moving my web site from a similarly specified machine to this one, I'm getting issues. The issue seems to be that randomly, as I'm clicking through the web pages being served, the browser will suddenly hang saying "waiting for mysite.com...". Sometimes the page will then timeout, or finally resolve after 20 to 30 seconds, but maybe missing the CSS style sheet. Very strange, as this is the only website installed on this new server, and only myself using/testing it. Server is installed in the same data centre below the old server. Has anyone else had a similar problem? I tried increasing the max workers pool to 10 (from 1), but this has no effect. Seems to happen most frequently after 1 or 2 minutes of inactivity on the website, then trying to load/refresh a web page. Many thank for any info and help. Kind Regards, Seb

  Read the article

• Query specific nameserver for a particular domain upon VPN connect

  - by MT

  Some background: I have a work laptop with Ubuntu 9.10 on it. I have a small network at home where I've been running some basic services (for myself/my family) for 10 some years. In my home network there is a nameserver (Fedora) running Bind 9 with two "views". One view is the "outside" view and it provides name resolution (to the Internet at large) for email, a wiki, and a couple of blogs. The "inside" view provides name resolution (to the internal RFC1918 addresses of theses servers) as well as all the inside hosts, network equipment, ...etc. I connect with an openvpn client to my home network from outside (such as work). What I'd like to be able to do is resolve names on my internal network across this VPN (so I get the RFC1918 "inside" responses) without fully changing my resolver to the DNS server at my hose. For example, if I connect to the VPN from work, I can change my resolver (by editing resolv.conf) to the DNS server at my house (across the VPN) and then successfully resolve all of the inside DNS names on my home network. The issue I have with this is that now I'm no longer able to resolve "inside" names provided by my work's DNS servers (because I'm using my home DNS server). Alternatively, I can connect to the VPN and access my home severs via IP addresses directly, but this is inconvenient and causes issues with Apache name-based hosting (among other things). In the end, the effect I'm trying to achieve is as follows: When I connect to the VPN I automatically start sending DNS requests for *.myhomedomain.com to my home nameserver, but any other requests continue to go the the nameserver I was using before (the one I received on my company LAN via DHCP). When I disconnect the VPN, requests for *.myhomedomain.com go back to the local LAN DNS server (e.g. all requests are going there now). I'm looking for suggestion at to how this can be accomplished.

  Read the article

• Strange WiFi problem - network is "not connected" but works

  - by GalacticCowboy

  Background I'm using a Windows XP tablet PC connected to my home network. I do broadcast the SSID, but otherwise the wireless network is locked down as tight as I can make it - WPA2 with a strong key, MAC filtering, etc. I've had this computer for about 4 years and the router for about 6 months. Before that, the previous router was set up in the same way, and I've never had any particular problems. Problem This morning - as I type this, as a matter of fact - Windows is reporting that none of my network connections are connected. Yet somehow my Internet connectivity still works! ipconfig reports a valid IP address, domain, etc., even though Windows apparently doesn't know about it. I tried repairing the connection and it had no effect - the repair eventually timed out. I'm pretty sure that I could reboot the computer and/or the router, etc. and it would fix the problem. However, I'm more interested in knowing if any of you have ever seen anything like this, and what might have caused it? Since it works I'm not inclined to mess with it too much. My concern is that it's a precursor to bigger problems.

  Read the article

• VirtualName-based local development host behind corporate proxy (MAMP)

  - by geerlingguy

  I am behind a corporate proxy server/firewall, and this firewall seems to not be too happy with my idea of local development. On my home computer (Mac/Leopard), I have MAMP running, with a rule in /etc/hosts that directs dev.example.com to 127.0.0.1, and I have a virtualhost set up in the httpd.conf file which works great for me. However, at work, I set up the exact same configuration, but am not able to access dev.example.com, likely due to some address/DNS translation going on via the proxy server. Here are the relevant details from Terminal: $ ping dev.example.com PING dev.example.com (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.025 ms $ host dev.example.com Host dev.example.com not found: 3(NXDOMAIN) I've tried adding dev.example.com to the list of bypass addresses in System Preferences (the 'Bypass proxy settings for these Hosts & Domains' list), but that had no effect. Is there any way I can develop locally using name-based hosts at work? I can access localhost, but can't get to the dev.example.com (or any other custom virtualhosts) here at work, which complicates other matters related to the sites on which I'm working...

  Read the article

• How to change password on RAR archive w/o modifying arch. files attributes (modified/created)?

  - by Larry78

  How do I change the password of an .RAR archive, without changing the date/time attributes of the files in the archive? Unfortunately you can't directly change the password of the archive with WinRAR, you have to extract the files, and then make a new archive with the new password. So the created/modified attributes of the files in the archive get changed. I know you can manually change the attributes of a file with available utilities - but there are hundreds of files in the archive, each with unique attributes, so it would take a very long time to "fix" each file before re-archiving it. I'm using WinRAR 3.51, the last free version. Windows XP Pro SP3. Update: I don't care if the output is a .RAR file or a ZIP file IZArc4.1 will convert the RAR to a ZIP, and it keeps the dates. The problem is it compresses the file - there isn't a "store" option, and setting the default to store in the main configuration doesn't effect conversions. The RAR contains uncompressed files. None of these other archiving programs will even do a conversion. A couple claim to, or try to, but the errors returned indicate a very lousy application. So far I've tried PeaZip, 7-Zip, FilZip, TugZip, SimplyZipSE, QuickZip, and WinShrink (from downloads.cnet.com). WinRAR gives the error "skipping encryped archive" when I try the conversion. It asks for the password first, and I know it's right, as I opened the archive, and I can read/view all the files in it. It works on non-encrypted files.

  Read the article

• Small maximum number of connections on a Linux router

  - by Eugene

  I have a Linux box acting as a router with no iptables or other firewall and no networking applications running on it, just pure router. I've put it in a test environment that generates many TCP connections, each having unique source and destination IP, and those connections go through this router. I'm observing that number of connections successfully created rise to approximately 500 and then no more connections can be created for several minutes, then another 100 connections can be created and there is another pause, and so on. If 10 connections for each source-destination pair are created, then maximum numbers go about 10 times up, so the problem is probably with many connections from different IPs. As traffic is simply routed, it doesn't have to do with number of file descriptors, iptables connection tracking and other things often proposed to check in similar cases. The box has plenty of free RAM and CPU, both NICs are gigabit. The kernel is 2.6.32. I've already tried increasing net.core.*mem_max, net.core.netdev_max_backlog and txqueuelen on both NICs, with completely no effect. What else should I check ? Is there some rate-limit in the kernel itself ?

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem. EDIT: In the end, nothing really worked, and I got really annoyed with the state of compiz and its support in Debian. Many nVidia driver revisions have passed and I am using Gnome 3 now, so I am accepting the best answers to this question even though the issue was not resolved.

  Read the article

• Getting the EFS Private Key out of system image

  - by thaimin

  I had to recently re-install Windows 7 and I lost my exported private key for EFS. I however have the entirety of my user directory and my figuring that the key must be in there SOMEWHERE. The only question is how to get it out. I did find the PUBLIC keys in AppData\Roaming\Microsoft\SystemCertificates\My\Certificates If I import them using certmg.msc it says I do have the private key in the information, but if I try export them it says I do not have the private key. Also, decryption of files doesn't work. There is also a "keys" folder at AppData\Roaming\Microsoft\SystemCertificates\My\Keys. After importing the certificates I copy those over into my new installation but it has no effect. I am starting to believe they are either in AppData\Roaming\Microsoft\Protect\S-1-5-21-...\ or AppData\Roaming\Microsoft\Crypto\RSA\S-1-5-21-...\ but I am unsure how to use the files in those folders. Also, since my SID has changed, will I be able to use them? The other parts of the account have remained the same (name and password). I also have complete access to the user registry hive and most of the old system files (including the old system registry hives). I do keep seeing references to "Key Recovery Agent" but have not found anything about using, just that it can be used. Thanks!

  Read the article

• Migrating ODBC information through a batch file

  - by DeskSide

  I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

  Read the article

• Samba access works with IP address only

  - by Sebastian Rittau

  I added a Debian etch host (hostname: webserver, IP address: 192.168.101.2) running Samba to a Windows network with a Windows 2003 PDC (IP address 192.168.101.3). The Samba server exports a public guest share, called "Intranet". The server shows up fine in the network, but trying to click on it produces an error dialog, stating I don't have the necessary permissions. So does entering \webserver manually and using \webserver\internet states that the path does not exist. Interestingly, accessing the share by IP address (\192.168.101.2 or \192.168.101.2\intranet) works fine. DNS is configured correctly, and "smbclient //webserver/intranet" on another Linux client works fine. One complicating issue is that the webserver is only a VMware virtual machine running on PDC server. Here is our smb.conf: [global] workgroup = Foobar server string = Webserver wins support = yes ; commenting out these wins server = 192.168.101.3 ; two lines has no effect dns proxy = no guest account = nobody [... snipped some unrelated bits, like logging ...] security = share [... snipped some password-related things ...] domain master = no [intranet] comment = Intranet path = /srv/webserver/contents browseable = yes guest ok = yes guest only = yes read only = yes create mask = 0775 directory mask = 0775

  Read the article

• Router(s) Issue: DNS quries sporadically fail with multiple computers hooked in

  - by bob-the-destroyer

  Basically, after anywhere from 5-60 minutes, DNS queries fail for a few minutes, then slowly begin to resolve correctly. Then the cycle repeats. This occurs only when more than one computer is on the network. All computers on the network experiences the same sporadic DNS outage at the same time. Wireless or wired, Linux or Windows, fresh OS install or old, browser or ping, same symptoms. Duplicated on 3 routers (not chained together, mind you) and 3 ISP's and 3 separate locations over the past several months. The only common theme is a single 5-yo WIN XP laptop which has been in use on the network throughout all this. There also may be anywhere between 1 - 10 devices hooked up wired or wirelessly at a time. The only reprieve I have from this torture is by using any VPN to an outside source - always smooth sailing. I typically set up any router to a) use WPA2/etc security; b) MAC whitelist; c) UPNP OFF (if available); d) always update firmware when available; e) obtain DNS from ISP automatically; f) set the router to act as DHCP server for the internal network. Adjusting channels has no effect. Any ideas?

  Read the article

• Windows Displays Double the Actual Installed Physical Memory

  - by Andrew Barber

  I have a server I've installed Windows Web 2008 R2 on, which is reporting that I have double the physical memory installed as is actually the case. In msinfo32 "Installed Physical Memory" shows as 2x what ever the actual installed amount is, though "Total Physical Memory" shows the correct amount. The "System" info window shows installed memory as 2x, with the correct amount in parenthesis listed as the "usable" amount). This server mistakenly had Windows Web 2008 (32-bit) installed on it just previously, and that OS also reported the same faulty information as Win2K8R2 is reporting. BIOS reports the correct amount, memtest was run on this server before installation, and a previous Windows 2000 instance installed on this system also reported the correct amount, as I recall. Server operation seems to be fine as well (it's only trying to use the correct amount of memory). The server is a generic pizzabox running on a SuperMicro X6DVL-EG with dual Xeon-3.2's. Memory installed are 4 matching mt18vddf12872g-335c3 sticks (1GB pc2700 DDR ECC REG cl2.5) This behavior occurs whether two or all four are installed. So, has anyone seen something like this before? Have any idea about what's causing it, and how I should be concerned about it? Everything else seems good so far, and I'll be upgrading the memory before putting the server into service, but I don't want to spend too much time/money/effort on the server if it's got something odd going wrong here. UPDATE: There was a question I ran into regarding memory sparing in the BIOS and a possible (buggy) effect thereof; however, flipping that bit back and forth in the BIOS revealed that isn't the issue. Still flummoxed a bit about this one, though I still have seen no negative impacts. Post-Answer Update (January 13, 2011): Upgrading the system with new, larger memory has fixed this issue.

  Read the article

• What is the fall off of subsecond throughput on Ethernet Network Interfaces

  - by Kyle Brandt

  On a network interface, speeds are given in term of data over time, in particular, they are bits per second. However, in the uber-fast world of computing -- a second is kind of a really long time. So for example, given a linear falloff. A 1 GBit per second interface would do 500MBit per half second, 250Mbit per quarter second etc. I imagine at certain units of time, this is no longer linear. Perhaps this is set by ethernet frequencies, system clock speeds, interrupt timers etc. I am sure this varies depending on the system -- but does anyone have more information or whitepapers on this? One of the main reasons I am curious is to understand output drops on interfaces. Even if the speed per second is much lower than the interface can handle -- perhaps there are spikes that cause drops for only small numbers of milliseconds. Perhaps various coalescing would hide this effect -- or perhaps increase it on the receiving interface? Do queues make a difference here? Example: So given if this is linear down to the MS we would have 1Mbit/MS, and if Wireshark isn't distorting what I see, should I see drops when I have a spike beyond 1Mbit?

  Read the article

• Truecrypt files corrupted after moving PC into another case

  - by Dygerati

  I recently bought a new PC case and transferred all of my PC hardware into it. The only hardware modification was the addition of two identical ram modules. The entire process went smoothly, and everything worked and booted as before. The only side-effect I found when accessing one my of file-based hidden truecrypt volumes shortly there after. Some of the files in the volume - NOT all - seemed to be entirely corrupted. The directory and file names are garbled characters, but a few of the directories in the same volume appear and function normally. Also, all files in the non-hidden tc volume were still intact. Is this not weird? The only other real change I could think of would be that the hard drives were connected to different SATA ports on the mobo. I really don't know how the truecrypt encryption works well enough to know what could cause this...and the fact that not all the files were corrupted makes it more bizarre still. So, first off (and I'm not too hopeful on this point), would it be possible to restore these files? I had a backup of most, but not all of the files involved. Other than that I'm just curious how this happened and how I can prevent it next time. Thanks!

  Read the article

• Nexenta, NFS and LOCK_EX

  - by Givre

  I'm currently using an LAMP architecture and I expect a big problem :( I have several http web server using PHP5. All are mounting via NFS (v3) the directory for all the hosted websites. The file server is running the Nexenta Storage Appliance using ZFS . The problem is all the NFS client trying to write something in a file over the NFS get this problem : This is inside the apache2 process: open("/nfs/website1/file.txt", ORDWR|OCREAT, 0600) = 11647 fstat(11647, {stmode=SIFREG|0600, st_size=23754, ...}) = 0 flock(11647, LOCK_EX And the process never get the LOCK and keep waiting for... always. The effect? All the apache2 procces get used and waiting.. my severs can't still proccess the others requests because there is no more proccess available. I don't now where to find a solution.. for me it.'s on the NFS server side.. but wich configuration is wrong or missing ? How can I find what is wrong? If you need more information about the configuration, just ask me what can help you more :)

  Read the article

• SSL Mail server connection times out on send()

  - by Jivan

  When trying to programmatically send an email from a website of mine, with PHP Pear Mail package with SSL connection, PEAR:Mail replies the following : Failed to connect to example.blabla.net:PORT [SMTP: Failed to connect socket: connection timed out (code: -1, response: )] I looked for similar questions on SO and SF, all the answers asking the OP to test a request on telnet or ssh in command line. So, that is what I did and here is what happens : $ ssh -l myusername -p PORT example.blablabla.net _ Here, '_' in the second line means that NOTHING happens. Indefinitely, which seems coherent with the timeout message I had from PEAR:Mail. So PEAR:Mail seems out of cause. But, what I have to tell you is that yesterday, it just worked. Connection was properly established, mails were properly sent, etc. Just today, it doesn't work anymore and I absolutely don't know why. I restarted Apache (in case an extension was broken), restarted mail services, etc. Still. No effect. Before yesterday (when it worked) and today (when it doesn't anymore), I just didn't touch the server and did nothing on it, simply because I took a day off to write some blog post! Have anyone of you encountered similar problem ? The problem seems quite common, judging after some googling, but the solution doesn't. Thanks for any help ! (note on config : CentOS 6.4 x86_64 with cPanel/WHM)

  Read the article

• Connections to IIS sometimes get stuck in CLOSE_WAIT state

  - by randomhuman

  Our application includes an ASP.Net web service that only needs to deal with a handful of clients. As such, the 10 incoming connection limit of Windows XP Pro is generally not a problem. However, on one particular server, connections are occasionally becoming stuck in the CLOSE_WAIT state. These connections build up over time and eventually new client connections are refused because the maximum number of connections are used up. From my googling it sounds like a failure of the webservice to properly close the connection can cause this problem, but as it works just fine on hundreds of other Windows XP pro machines I can't see it being a bug in our code. It also ran fine on the affected machine until some shenanigans on the part of the end user (I think they set about deleting duplicate files in order to reduce their disk usage, but they did not exactly come clean about it). What could the user have changed to introduce this problem? Is there any way I can force connections that are in CLOSE_WAIT to time out rather than letting them hang around? I have seen suggestions to reduce TcpTimedWaitDelay, but that only relates to the TIME_WAIT state, and changing it did not have any effect.

  Read the article

• Problem with Amiga 1200 accelerator board

  - by cc0

  I just recently walked past a dump, where in the corner of my eye I spotted something that looked like a huge keyboard. I went to take a closer look, and found out that it was an Amiga 1200 with a 030 accellerator board and scala dongle. Jackpot! So anyway; I dried it, cleaned it, it works, but the floppy was not powering on and same with the harddrive. I am using an old Amiga 1200 PSU that was making some strange high pitch noise when I tried to boot the amiga with the harddrive installed in it. I removed the harddrive and it booted fine with the PSU not emitting any detectable noise. However, when I have the 030 installed it sometimes reboots and shows a red "Software Error" screen. I tried removing the memory on the board, same effect. Sometimes it does not boot at all, just gives a black screen. Someone suggested the card had problems with 3.1 roms, but this amiga has only 3.0 roms installed. Does anyone have any apparent theories as to why it seems unstable? I don't have any other Amiga parts to cross-swap with to test a lot of things, so I'd really appreciate some sound input here so I'd know what to look for in order to try fix it. And merry Christmas everyone :]

  Read the article

• Fake demostration software for command line

  - by Joe

  I'm looking for some software that would be useful for giving demonstrations. I regularly have to show the effects of scrips ect to classes while talking about their effects, and equaly regularly I have finger trouble and have to rewrite various commands - wasting class time and general energy. I'd like to be able to record a sequence of commands in advance, and then play them back at the speed of my choosing. So I might have a file that containes the commands: echo "hello world!" ls ls -l ls -l | sort I'd like to be able to play these commands back by typing similar ones in. So I'd have a blinking command prompt and if I typed 'echo "hxxx' the command prompt would read home$echo "hell and if I typed any other letters the terminal would fill up with the remainder of the command until I press enter, when it executes the command. The point is that even if I screw up the command when typing it, the command that I'd prepared in advance would be executed. My question is - does similar software exist for giving demonstrations? or even, is this an easy thing to script up...? EDIT - two quick things first of all I'm on osx - but it would be nice to get a general solution for other people who arrive here from google. and second a lot of the comments/answers are concentrating on, in effect, making it fast and easy to enter long commands by means of hotkeys and the like. Actually I'd like it to at least look like I'm typing live - that's why I put in the bit about the one-to-one keymapping, but I don't think I explained that quite as well as I could have...

  Read the article

• User Group Policy in Server 2008 to set Default Profile settings

  - by Chris

  I have computers to deploy and want to apply changes to the default user policy on these PCs automatically. What's the best way to do this? Our current procedure is: Create the computer account in an OU called "Deployment" on our server Unbox the PC Login as the user who will be receiving the PC Change settings (pre-configure outlook, authorize Office, etc.) move computer account to correct OU Place the PC on the users desk. I would like to make as many of the changes in step #4 with Group Policies applied to the Deployment OU if possible since they're largely repeated for every computer. There are a dozen policies created and the computer ones apply correctly but the user policies do not. I understand this is because the end user is not in our "Deployment" OU. I don't want to apply these settings to the user at their current station just the new PC I'm working on. I believe I have the desired effect with Group Policy Loopback Replace enabled on policies that need user policies changed but this just feels wrong/inefficient/complicated to maintain. Am I doing this correctly? Is Group Policy Loopback the only way to change user accounts on one computer? What do you do to setup a user on a new PC?

  Read the article

• Cannot Add Particular Word to Dictionary

  - by WCWedin

  I am trying to add a particular word to my custom dictionary using Word 2007. (The word happens to be "deserialized".) When I right-click on the word and click Add to Dictionary, the red underline does not go away. When I use the Spelling & Grammar tool from the Review tab on the ribbon, it will stop on that word; clicking the Add to Dictionary button has no effect. Oddly, I am able to add other words to the custom dictionary without a problem. I recently added "deserializes", for instance. I have only encountered this problem with that one particular word. Does anyone know what might be wrong and how I might fix it? Clarifications My document and all its content is set to English (United States). My custom dictionary is set to apply to All Languages, which is the default value. "Serialize" is in the US English default dictionary, but "deserialize" and its various forms is not.

  Read the article

• How to get IE to open JavaScript as text

  - by Pete

  I am running IE 9. Up until last week sometime, if I would put the URL of a JavaScript file in the address bar, it would show the JavaScript as text in the browser window. Now when I do that, it wants to download the JavaScript file. How can I revert it to the previous handling? This is annoying since I'm developing a web application and if I can get it to display the .js files as text in the browser, then I can refresh it to force the cache to update. Update: I've tested on several co-workers machines. For some, browsing to .js files renders them in the browser (IE 9 in all cases). In others, it asks for a download. File associations don't seem to have any effect. One co-worker we tested with IE and Chrome. IE wanted to download it, but Chrome rendered it as text. This makes me think it's an IE issue and not an OS issue.

  Read the article

• Read access to Active Directory property (uSNChanged)

  - by Tom Ligda

  I have an issue with read access to the uSNChanged property when doing LDAP searches. If I do an LDAP search with a user that is a member of the Domain Admins group (UserA), I can see the uSNChanged property for every user. The problem is that if I do an LDAP search with a user (UserB) that is not a member of the Domain Admins group, I can see the uSNChanged property for some users (UserGroupA) and not for some users (UserGroupB). When I look at the users in UserGroupA and compare them to the users in UserGroupB, I see a crucial difference in the "Security" tab. The users in UserGroupA have the "Include inheritable permissions from this object's parent" unchecked. The users in UserGroupB have that option checked. I also noticed that the users in UserGroupA are users that were created earlier. The users in UserGroupB are users created recently. It's difficult to quantify, but I estimate the border between creation time between the users in UserGroupA and UserGroupB is about 6 months ago. What can cause the user creation to default to having that security property checked as opposed to unchecked? A while back (maybe around 6 months ago?) I changed the domain functional level from Windows Server 2003 to Windows Server 2008 R2. Would that have had this effect? (I can't exactly downgrade the domain functional level to test it out.) Is this security property actually the cause of the issue with read access to the uSNChanged property on LDAP searches? It seems correlated, but I'm not sure about causation. What I want in the end is for all authenticated users to have read access to the uSNChanged property for all users when doing an LDAP search. I would also be OK if I could grant read access for that property to an AD group. Then I can control access by adding members to the group.

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >