Search Results

Search found 10050 results on 402 pages for 'graphics card'.

Page 161/402 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

  • Diverting sound output of MCE to SPDIF

    - by Saxtus
    I have an ASUS SupremeFX II audio card (which in fact is an onboard audio riser slot) with the default drivers that are pre-installed by Windows 7 x64 for this card. I am able to manually switch between analog output and SPDIF output by the means of control panel (or external utilities like STADS), a change that affects all applications. The problem is that by doing that every time I am about to launch Windows Media Center, except that it's not that elegant, also makes all other Windows application's sounds to pass through SPDIF too, bypassing analog output completely, blending with what I am watching at Windows Media Center. Is there a way to make SPDIF as the default playback device for Windows Media Center? I know other programs that have a setting like that (foobar2000 for example) working like charm, allowing me to even have different outputs working at the same time (tested with my current card successfully). But when comes to Windows Media Center... it just use what the default playback device is all the time. The only setting that I know of, is under: Settings General Windows Media Center Setup Set Up Your Speakers and what it does is to just change the default playback device for entire system. Please help!

    Read the article

  • What speed are Wi-Fi management and control frames sent at?

    - by Bryce Thomas
    There are a bunch of different 802.11 Wi-Fi standards, e.g. 802.11a, 802.11b, 802.11g, 802.11n etc. that all support different speeds. Wi-Fi frames are generally categorised as one of the following: Data frames - carry the actual application data Control frames - coordinate when its safe to send/reduce collisions Management frames - handle connection discovery/setup/tear down (e.g. AP discovery, association, disassociation) My question is about whether all these frames, and specifically management frames, are transmitted at the fastest supported speed available, or whether certain classes of frames are transmitted at some lowest common denominator speed. I have noticed that when I put an 802.11b/g only device into monitor mode and capture traffic over the air, I still see management frames (e.g. association/disassociation) being transmitted between my phone and AP which are both 802.11n, even though 802.11n has a higher transfer rate. So I am imagining one of two possibilities: My 802.11n phone/AP had to negotiate a slower speed for some reason and that's why I can see their frames on my 802.11b/g monitoring device. Management frames (and perhaps control frames also?) are sent at a lower speed, and it's only data frames that are transmitted faster with newer 802.11 standards. The reason I would like to know which one of these two possibilities (or perhaps a third possibility) is the case is that I want to capture management frames, and need to know whether using an 802.11b/g card is going to lead to me missing some frames sent at higher speeds than the monitoring card can observe. If management frames are indeed sent at a slower rate, then it's all good. If I just happen to be seeing the management frames because my phone/AP have negotiated a slower rate though, then I need to reconsider what card I use for packet capture.

    Read the article

  • ATI HDMI Audio disappears in Windows 7 when a TV is connected

    - by jsalonen
    So far I have unsuccessfully googled for HOURS with no luck fixing this very annoying problem. The settings is the following: I have PC running Windows 7 RC (64-bit) Video card is a ATI Radeon 4850 series card (Sapphire HD 4850 512MB to be exact) The video card has HDMI out with built-in audio chip I have an HDMI cable connecting the PC to a TV (Sony Bravia series) The problem is that when I connect the HDMI cable to the TV, the ATI HDMI Sound output device disappears completely from the list of playback devices in Windows. As a workaround I can restore the audio by re-installing the HDMI audio driver. However, when I disconnect the TV the driver disappears again. So basically, every time I want to watch stuff on my TV, I have to reinstall audio driver, which of course is VERY annoying. EDIT: I have figured out that I do not need to re-istall the HDMI audio driver to restore sound; I only need to reboot my computer with the HDMI cable plugged in to restore the audio driver. This suggests that the problem has something to do with information passed from TV to computer, which makes my HDMI Audio driver disappear. Are there any other, more elegant workarounds for this problem? All help is much appreciated!

    Read the article

  • SPDIF passthrough not working in Windows 7

    - by adriangrigore
    Hi, I'm running Windows 7 on a computer with an Audigy Platinum eX sound card connected to a surround receiver via optical cabling. Sound works fine when listening to non-surround audio sources, such as windows sounds or MP3. However, when I view a DVD in Media Center and the SPDIF passthrough kicks in, I can only hear an awful noise instead of the movie soundtrack. Also, the receiver does not show the Dolby Digital or DTS symbol, but stays at Dolby Prologic, so it seems it doesn't identify the sound encoding properly. I could switch off SPDIF passthrough and use the sound card's decoder instead, but that's not an option for me since it would create more problems with regular MP3 playback via additional Stereo Receiver which is also connected to the same sound card. I've tried both the default Audigy drivers that come with Windows 7 and the latest drivers from the Soundblaster website, but the problem remains unchanged. Also, I have ensured that the receiver's Dolby Digital decoder is not broken by successfully connecting it to my PS3 to view a Dolby Digital DVD. Besides, SPDIF passthrough was working fine in Vista before I upgraded to Windows 7. Is there anything else I could try?

    Read the article

  • Slow File Copy observed copying 40GB files across network to iSCSI device

    - by Rick
    Here's a curious ones for the gurus: Setup: Source Machine: Windows Server 2003 R2 machine with local hard drive. VHD file of 40GB. 1 x 1Gbps network card, Cat6 cable, switch. Target Machine: Windows Server 2008 R2 machine with iSCSI connection to iSCSI target on separate machine (1TB, RAID5). 1 x 1Gbps network card, Cat6 cable, connected to same switch as for Source Machine. Second 1Gbps network card, Cat6 cable, connected via isolated switch to the iSCSI target. Switches are Netgear JGS524 model (web managed). If I copy from the Win2003R2 machine to Win2008R2 machine local drive I get 40GB in 45 minutes, 36 seconds. If I copy from the Win2008R2 machine to the iSCSI target (local drive to iSCSI target) I get 40GB in 37 minutes 56 seconds. If I copy from the Win2003R2 machine to the iSCSI target via the Win2008R2 machine I get 40GB in 3 hours, 50 minutes, 24 seconds. All copies were done via the following command issued on the Win2008R2 box: XCOPY <source> <target> /J XCOPY /J - Copies using unbuffered I/O. Recommended for very large files. So, what's the bit I'm missing here? Why does a back-to-back copy take in total 1 hour, 23 minutes, 32 seconds when a "straight through" copy take almost 3 times as long? Switches show no errors, network hovers around the 3% utilisation mark for the duration of the copy (whereas the "back-to-back" copies are around the 25% utilisation mark). What have I missed?

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • NVIDIA GeForce GT750M drivers for Ubuntu 13.10 on iMac

    - by Eugene B
    I have just got a new iMac 14.3 with 21.5' display. It has Intel i7 processor and NVIDIA GeForce GT750M graphics card with GPU (Device ID: 0x00fe9). I have installed Ubuntu 13.10 on it (dual boot with refit). Everything works fine apart from graphics. It is clear that graphics' not accelerated, and there are no drivers suggested in the "Additional drivers" section. I have tried to Install nvidia drivers from the repository. Download nvidia drivers and install them manually. Follow instructions here. Follow instructions here. Follow instructions here. Install bumblebee. Play around with xorg.conf file. Blacklist nouveau. As you may guess, nothing worked. The weirdest thing is, that when I boot from a LiveCD, it picks up screen resolution and all the rest correctly, though when I install the system to my Hard Drive it clearly does not have proper drivers. Does anyone have any suggestion what to do?

    Read the article

  • Problem with setting up raid5 on Freenas, Please help.

    - by Benjy23
    Hey Guys, I've been running Freenas for awhile now. Hardware is 1.8celeron Ram 1GB Sata Card is Via - not sure the model.... its 2 ports and I have 6 x 1.5TB HDs All ran ok while running on 1.5TB, no raid. I'm now trying to create a raid5 with my 6 hds. Software raid... is it normal for it to take roughly up to 2 weeks just to build the raid? Sorry, I'm very new to implementing raid and googling doesn't tell much other than it takes a long time. Also the Raid building process seems to fail many times... going to degraded. I suspect its cos 4 of my HDs are connected to my motherboard and the other 2 are connected to my sata card...what's your take? I'm considering 2 options now... either get a 8 port sata card and attach all the HDs to it. Or get a raid controller 8 portcard which is probably gonna be more pricey... also how do you access hardware raid through Freenas? I like how Freenas emails you should your harddrive fails so can this be done as well with hardware raid? Thanks in advance guys.

    Read the article

  • Ubuntu 10.04 freezing and Ctrl + Alt + Backspace does nothing but music keeps playing

    - by Bryce Thomas
    I'm having intermittent problems where the screen will freeze in Ubuntu. I've tried using Ctrl + Alt + Backspace to restart the X-server, though this does nothing. When the freeze occurs, there's a small square of black dashes around the mouse pointer - maybe 1 inch in size. These dashes look a lot like a 2d barcode. The rest of the screen looks normal, but I can't move the mouse and none of the keyboard shortcuts work to do anything. However, music that I begin playing before the freeze continues to play, which seems to indicate it hasn't stalled up completely. I've noticed a similar freezing problem when I'm using Windows 7. That is, I see the same barcode like dashes around the mouse pointer when it freezes up. So I'm guessing it's either a driver or hardware problem. I thought if it was a hardware problem though, the whole computer might stop working (i.e. music would stop playing)? The video card I am using is an Nvidia, and I believe it's in the 7600 range. In Ubuntu I have the drivers for the card set to the latest available (proprietary). Ideally I'd like to be able to continue using the proprietary drivers. Is there any known issues with the drivers for this model graphics card, or has anyone experienced the same problem and knows how to fix it?

    Read the article

  • Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

    - by Wesley
    Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

    Read the article

  • How CPU communicates with HW

    - by b-gen-jack-o-neill
    Good day. I am new here, but I could not find answer to my question using google, so I help I do not violate any rules. So, basically, all I want to ask is, how CPU comminucates with other HW, such as printers, Graphic card, sound card, LAN card etc. I know, that for basic system I/O, you can use BIOS interrupts. INT 10h I believe is for display output. But, what I would like to know is, what actually happens when you execute instruction int 10h. From desription of int instruction, it should jump to routine, which is stored on adress pointed by adress stored in iterrupt table. But how does this routine get into the RAM? Does BIOS save that routines to the RAM? And what actually that routine does? I mean, CPU can only acess RAM, right? So how can now acess some other HW? Is there some special instrucion for it? Or is CPU somehow connected to BIOS, and than BIOS actually does the work? And the last thing, does even OS like Windows or GNU/Linux use BIOS interrupts, or can OS acess HW directly? Thanks.

    Read the article

  • Triple monitor setting in Linux with USB-HDMI adapter

    - by Oscar Carballal
    I'm trying to set up a triple monitor desktop at my office using Fedora 17, but it seems impossible, let me explain the setting: Laptop ASUS K53SD with 2 graphic cards, Intel and nVidia (Screen controled by Intel card) 24" Full HD monitor connected to the HDMI output (controlled by Intel card) 23" Full HD monitor connected to an USB-HDMI adapter (via framebuffer in /dev/fb2, apparently) VGA output (not used) controlled by nVidia card First of all, the USB-HDMI adapter works perfectly, it gives me a green screen (which means the communication is OK) and I can make it work if I set up a single monitor setting via framebuffer in Xorg. Here I leave the page where I got the instructions: http://plugable.com/2011/12/23/usb-graphics-and-linux Now I'm trying to set up the the two main monitors (laptop and 24") with the intel driver and the 23" with the framebuffer, but the most succesful configuration I get is the two main monitors working and the third disconnected. Do you have any idea what can I do to make this work? Here I leave my xRandr output and my Xorg conf: -> xrandr Screen 0: minimum 320 x 200, current 3286 x 1080, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA2 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 531mm x 299mm 1920x1080 60.0*+ 50.0 25.0 30.0 1680x1050 59.9 1680x945 60.0 1400x1050 74.9 59.9 1600x900 60.0 1280x1024 75.0 60.0 1440x900 75.0 59.9 1280x960 60.0 1366x768 60.0 1360x768 60.0 1280x800 74.9 59.9 1152x864 75.0 1280x768 74.9 60.0 1280x720 50.0 60.0 1440x576 25.0 1024x768 75.1 70.1 60.0 1440x480 30.0 1024x576 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 720x576 50.0 848x480 60.0 720x480 59.9 640x480 72.8 75.0 66.7 60.0 59.9 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) 1920x1080_60.00 60.0 The Xorg file: # Xorg configuration file for using a tri-head display Section "ServerLayout" Identifier "Layout0" Screen 0 "HDMI" 0 0 Screen 1 "USB" RightOf "HDMI" Option "Xinerama" "on" EndSection ########### MONITORS ################ Section "Monitor" Identifier "USB1" VendorName "Unknown" ModelName "Acer 24as" Option "DPMS" EndSection Section "Monitor" Identifier "HDMI1" VendorName "Unknown" ModelName "Acer 23SH" Option "DPMS" EndSection ########### DEVICES ################## Section "Device" Identifier "Device 0" Driver "intel" BoardName "GeForce" BusID "PCI:0:02:0" Screen 0 EndSection Section "Device" Identifier "USB Device 0" driver "fbdev" Option "fbdev" "/dev/fb2" Option "ShadowFB" "off" EndSection ############## SCREENS ###################### Section "Screen" Identifier "HDMI" Device "Device 0" Monitor "HDMI1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "USB" Device "USB Device 0" Monitor "USB1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • Wireless does not work on Ubuntu 9.04

    - by Yongwei Xing
    Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

    Read the article

  • MacBook Pro and Backtrack 5R1 Configuration

    - by user119346
    I have a Macbook pro Quad core (2.2/8gb ram/750gb hdd). I have went through tons of forums on the Internet, but none of them seemed to be updated for the current Backtrack 5R1, or the question of getting it to correctly work on the MBP. Can anyone help? I don’t have a USB Dongle, and I want to be able to use the internal airport extreme wireless of the MBP to use BT 5R1. I have downloaded Backtrack 5R1 onto VMWare Fusion, and got it up and running, but to no avail. It keeps recognizing my card as a Ethernet connection. Kismac wont recognize the card either. So what I am asking for is this: The proper “download method.” for Backtrack 5R1 to my MacBook Pro. (YES I AM WILLING TO RE-DOWNLOAD BT 5R1). The Complete process from start to finish, UP TO DATE, from someone who has done this using an MBP Running Lion OSX. The proper tweaks, settings, or commands to get my airport extreme wireless card to work (it is BROADCOM 4331 I think). The wireless connection I need to use the tools on both Backtrack 5R1 and Kismac. I mainly need to test WEP cracking on my network for security. The difference between running BT 5R1 on VMWARE Fusion and running from downloading it directly to the MBP, if there is, How to download it directly to the MBP?

    Read the article

  • Windows Explorer Hangs on Right-Click

    - by Bryan
    I am not sure if this is the right site to post this one as I typically post coding questions on stackoverflow. But I'll ask anyways and hopefully someone can move it if it's incorrect. Currently I have a customer built PC, utilizing an Intel i7 chip, 1300WATT PSU, 8Gigs of RAM, and two video cards. Originally I had the one video card (NVIDIA) that used the PSU and had two DVI output. After purchasing a third monitor I installed another ATI) graphics card not needed any PSU connectors. After installing and restarting, I noticed that when I right-click on my desktop, or through Windows Explorer it will hang, freeze then restarted. Sometimes after Windows Explorer restarts the problem dissipates. I checked to make sure everything was connected properly and it was. I repaired the ATI Catalyst Control Center to see if that had an issue, and I checked to see if either video card required updated drivers. Nothing worked. I tried restarting my PC and that didn't work. I tried using ShellXView (I forgot what it's actually called) and tried closed processes but that didn't work. Does anyone have any idea what could have caused this orpossible solutions I should try?< Thanks in advance.

    Read the article

  • VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

    - by Dayton Brown
    I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

    Read the article

  • fglrx-legacy-driver not seeing Radeon HD 4650 AGP

    - by Rocket Hazmat
    I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

    Read the article

  • Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

    - by alexleonard
    I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

    Read the article

  • Screen randomly goes blue/black/white

    - by FubsyGamer
    Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

    Read the article

  • Proper approach to debug PC startup problems (POST)

    - by saurabhj
    My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

    Read the article

  • How to write rules for persistent net names?

    - by ndemou
    I know that a process generates persistent network card names based on rules found in /lib/udev/rules.d/75-persistent-net-generator.rules. I also know how to completely disable this process with a simple echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules but I've read that I "could also write my own rules file to give the interface a name — the persistent rules generator ignores the interface if a name has already been set" (/etc/udev/rules.d/README confirms that this is possible). Do you have any pointers to documentation about how to write such rules? (I mostly care about Debian/Ubuntu and a bit less for CentOS) As a specific example of why I want to write custom rules: I have two identical servers with one onboard LAN and one PCI LAN. In case of HW failure I want to be able to move disks from HW#1 to HW#2 and it's important for eth0 to continue pointing to the onboard card and eth1 to the PCI card (no one wants to mess with cabling in the middle of a HW failure panic). My current workaround works but is a lot of work[1] so I wonder if writing custom rules would allow me to express something simple like this: cards with MAC A or B should be named eth0 cards with MAC C or D should be named eth1 follow default naming scheme for anything else [1] install the OS in HW#1 and keep a copy of /etc/udev/rules.d/70-persistent-net.rules. Move the disks to HW#2 and keep a second copy of the same file. Concatenate the two copies and manually edit the NAME="ethX" part. Replace /etc/udev/rules.d/70-persistent-net.rules with my version. Finally disable auto-creation of a new 70-persistent-net.rules using echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules

    Read the article

  • ATI Radeon 5670 Won't Show Resolutions over 1400x900

    - by Phil Sandler
    Just got my new Dell computer with Windows 7 and an ATI Radeon 5670. I attached it to my current monitor, which is a Samsung 24" (2443bwt). Windows 7 does not allow me to display in resolutions greater than 1400 x 900. The setup through a VGA cable into the VGA port of the card. The card also has a DVI port, but I need to use the VGA port because a KVM that supports VGA only. My old PC (which is Windows XP, GeForce 8600 video) can display in 1900 x 1200 on the same monitor (which is what I want) and even higher. It does this through a vga cable also connected to the KVM (through the DVI port but using an adapter). I have tried the same setup (DVI = VGA adapter) on the new PC and nothing changed. I have tried: Updating the drivers via Windows "Update Driver" (says they are current) Installing the updated version of the drivers from ATI (made no difference) Installing Powerstrip (all the options I would need for a custom resolution are greyed out) Installing the drivers/software from ATI caused the ATI Catalyst Control Center software to stop functioning, so I can no longer even start it. I have found some references to other people having this problem and instructions on cleaning the software off and reinstalling it (as uninstalling normally doesn't solve it). I will try this tonight. In any case, I didn't see any options in CCC that would allow me to override the settings for max resolution. However I didn't tinker with it too much before I tried updating the drivers, so I may have missed a setting. I contacted Samsung via online chat and they say it's a problem with the video card/driver (of course--what else would they say?). Any thoughts on what else I could try?

    Read the article

  • Problem with setting up RAID 5 on FreeNAS

    - by Benjy23
    I've been running FreeNAS for a while now. Hardware is 1.8 GHz Celeron, RAM 1 GB. SATA card is Via - I am not sure about the model. It's 2 ports and I have 6 x 1.5 TB hard drives. All ran OK while running on 1.5 TB, no RAID. I'm now trying to create a RAID 5 with my 6 hard drives. Software RAID. Is it normal for it to take roughly up to 2 weeks just to build the RAID? Sorry, I'm very new to implementing RAID and googling doesn't tell much other than it takes a long time. Also the RAID building process seems to fail many times. Going to degraded. I suspect it's because 4 of my hard drives are connected to my motherboard and the other 2 are connected to my SATA card. What's your take? I'm considering 2 options now. Either get a 8 port SATA card and attach all the hard drives to it. Or get a RAID controller 8 portcard which is probably going to be more pricey. Also how do you access hardware RAID through FreeNAS? I like how FreeNAS emails you should your harddrive fails. Can this be done as well with hardware RAID?

    Read the article

  • Updating ASUS BIOS on Windows 7 64bit

    - by joesavage
    I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

    Read the article

  • How to disable monitor auto detection in Windows 7?

    - by Jay Yother
    I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

    Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >