Search Results

Search found 4489 results on 180 pages for 'logging'.

Page 162/180 | < Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >

  • ASA 5505 stops local internet when connected to VPN

    - by g18c
    Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

    Read the article

  • Hour-long shutdown duration "shutting down hyper-v virtual machine management service"

    - by icelava
    I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE Ok so i left it hanging over an hour while attending to other matters, and thankfully the host cleanly restarted. I can operate the guest machines fine now. Phew. Hyper-V must have been crawling for some reason. The VMs have been observed to become slow in the past when the host has been up for a long duration (two weeks to a month), but never this slow. Would love to know what types of performance monitoring items i can observe to give a hint why this can happen. UPDATE 2012-02-13 In the months ever since, Hyper-V has stalled into this state another two times. It appears so randomly and without any error event logs to hint what is causing it enter this "drunkard" state. Just an Hyper-V management service timeout. Log Name: System Source: Service Control Manager Date: 13/2/2012 9:16:48 AM Event ID: 7043 Task Category: None Level: Error Keywords: Classic User: N/A Computer: elune Description: The Hyper-V Virtual Machine Management service did not shut down properly after receiving a preshutdown control. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7043</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2012-02-13T01:16:48.882901900Z" /> <EventRecordID>567844</EventRecordID> <Correlation /> <Execution ProcessID="764" ThreadID="8484" /> <Channel>System</Channel> <Computer>elune</Computer> <Security /> </System> <EventData> <Data Name="param1">Hyper-V Virtual Machine Management</Data> </EventData> </Event> The only means out of it is to restart the system.

    Read the article

  • Where's my memory?! Nginx + PHP-FPM front end webserver slows to a crawl...

    - by incredimike
    I'm not sure if I have a problem with a memory leak (as my hosting company suggests), or if we both need to read http://linuxatemyram.com. Maybe you clever people can help us out? This is a front-end webserver VM running essentially only nginx & php-fpm on RHEL 5.5. This server is powering Magento, a PHP eCommerce thinggy. The server is running in a shared environment, but we're changing that soon. Anyway.. after a reboot the server runs just fine, but within a day it will grind itself into nothingness. Pages will take literally 2 minutes to load, CPU spikes like crazy, etc.. The console is even sluggish when I SSH in. It's like my whole server is being brought to its knees. I've also been monitoring the DB server via top and tcpdumping incoming traffic. The DB stays idle for a good portion of that "slow" load time. When i start seeing queries coming from the front-end server, the page loads soon afterward. Here are some stats after me logging in during a slow-down, after restarting php-fpm: [mike@front01 ~]$ free -m total used free shared buffers cached Mem: 5963 5217 745 0 192 314 -/+ buffers/cache: 4711 1252 Swap: 4047 4 4042 [mike@front01 ~]$ top top - 11:38:55 up 2 days, 1:01, 3 users, load average: 0.06, 0.17, 0.21 Tasks: 131 total, 1 running, 130 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.3%sy, 0.0%ni, 99.3%id, 0.3%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.3%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 6106800k total, 5361288k used, 745512k free, 199960k buffers Swap: 4144728k total, 4976k used, 4139752k free, 328480k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31806 apache 15 0 601m 120m 37m S 0.0 2.0 0:22.23 php-fpm 31805 apache 15 0 549m 66m 31m S 0.0 1.1 0:14.54 php-fpm 31809 apache 16 0 547m 65m 32m S 0.0 1.1 0:12.84 php-fpm 32285 apache 15 0 546m 63m 33m S 0.0 1.1 0:09.22 php-fpm 32373 apache 15 0 546m 62m 32m S 0.0 1.1 0:09.66 php-fpm 31808 apache 16 0 543m 60m 35m S 0.0 1.0 0:18.93 php-fpm 31807 apache 16 0 533m 49m 30m S 0.0 0.8 0:08.93 php-fpm 32092 apache 15 0 535m 48m 27m S 0.0 0.8 0:06.67 php-fpm 4392 root 18 0 194m 10m 7184 S 0.0 0.2 0:06.96 cvd 4064 root 15 0 154m 8304 4220 S 0.0 0.1 3:55.57 snmpd 4394 root 15 0 119m 5660 2944 S 0.0 0.1 0:02.84 EvMgrC 31804 root 15 0 519m 5180 932 S 0.0 0.1 0:00.46 php-fpm 4138 ntp 15 0 23396 5032 3904 S 0.0 0.1 0:02.38 ntpd 643 nginx 15 0 95276 4408 1524 S 0.0 0.1 0:01.15 nginx 5131 root 16 0 90128 3340 2600 S 0.0 0.1 0:01.41 sshd 28467 root 15 0 90128 3340 2600 S 0.0 0.1 0:00.35 sshd 32602 root 16 0 90128 3332 2600 S 0.0 0.1 0:00.36 sshd 1614 root 16 0 90128 3308 2588 S 0.0 0.1 0:00.02 sshd 2817 root 5 -10 7216 3140 1724 S 0.0 0.1 0:03.80 iscsid 4161 root 15 0 66948 2340 800 S 0.0 0.0 0:10.35 sendmail 1617 nicole 17 0 53876 2000 1516 S 0.0 0.0 0:00.02 sftp-server ... Is there anything else I should be looking at, or any more information that might be useful? I'm just a developer, but the slowdowns on this system worry me and make it hard to do my work.. Help me out, ServerFault!

    Read the article

  • How to troubleshoot problem with OpenVPN Appliance Server not able to connect

    - by Peter
    1) I have a Windows Server 2008 Standard SP2 2) I am running Hyper-V and have the OpenVPN Appliance Server virtual running 3) I have configured it as it said, only issue was that the legacy network adapter does not have a setting the instructions mention "Enable spoofing of MAC Addresses". My understand is that before R2, this was on by default. 4) Server is running, web interfaces look good 5) I am trying to connect from a Vista 64 box and cannot 5a) If I set to UPD I am stuck at Authorizing and client log looks like: 10/11/09 15:00:42: INFO: OvpnConfig: connect... 10/11/09 15:00:42: INFO: Gui listen socket at 34567 10/11/09 15:00:42: INFO: sending start command to instantiator... 10/11/09 15:00:42: INFO: start 34567 ?C:\Users\Peter\AppData\Roaming\OpenVPNTech\config?02369512D0C82A04B88093022DA0226202218022A902264022AE022B? 10/11/09 15:00:42: INFO: Got line from MI->>INFO:OpenVPN Management Interface Version 1 -- type 'help' for more info 10/11/09 15:00:42: INFO: Got line from MI->>HOLD:Waiting for hold release 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: real-time state notification set to ON 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: bytecount interval changed 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: hold flag set to OFF 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: hold release succeeded 10/11/09 15:00:43: INFO: Got line from MI->>PASSWORD:Need 'Auth' username/password 10/11/09 15:00:43: INFO: Processing PASSWORD. 10/11/09 15:00:43: INFO: OvpnClient: setting need auth to true. 10/11/09 15:00:43: INFO: OvpnConfig: Setting need auth to true. 10/11/09 15:00:43: INFO: Got auth request from active_config from 0 10/11/09 15:00:47: INFO: Sending Credentials.... 10/11/09 15:00:47: INFO: Sending 25 bytes for username. 10/11/09 15:00:47: INFO: Sent 25 bytes for username. 10/11/09 15:00:47: INFO: Sending 30 bytes for password. 10/11/09 15:00:47: INFO: Sent 30 bytes for password. 10/11/09 15:00:48: INFO: Got line from MI->SUCCESS: 'Auth' username entered, but not yet verified 10/11/09 15:00:48: INFO: Got line from MI->SUCCESS: 'Auth' password entered, but not yet verified 10/11/09 15:00:48: INFO: Got line from MI->>STATE:1255287647,WAIT,,, 10/11/09 15:00:48: INFO: Got line from MI->>BYTECOUNT:0,42 10/11/09 15:00:48: INFO: Got line from MI->>BYTECOUNT:54,42 10/11/09 15:00:48: INFO: Got line from MI->>STATE:1255287648,AUTH,,, 10/11/09 15:00:50: INFO: Got line from MI->>BYTECOUNT:2560,2868 10/11/09 15:00:52: INFO: Got line from MI->>BYTECOUNT:2560,3378 5b) I setup server for tcp and try to connect, I get a loop of authorizing and reconnecting. Log looks like: 10/11/09 15:00:42: INFO: Got line from MI->>HOLD:Waiting for hold release 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: real-time state notification set to ON 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: bytecount interval changed 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: hold flag set to OFF 10/11/09 15:00:43: INFO: Got line from MI->SUCCESS: hold release succeeded 10/11/09 15:00:43: INFO: Got line from MI->>PASSWORD:Need 'Auth' username/password 10/11/09 15:00:43: INFO: Processing PASSWORD. 10/11/09 15:00:43: INFO: OvpnClient: setting need auth to true. 10/11/09 15:00:43: INFO: OvpnConfig: Setting need auth to true. 10/11/09 15:00:43: INFO: Got auth request from active_config from 0 10/11/09 15:00:47: INFO: Sending Credentials.... 10/11/09 15:00:47: INFO: Sending 25 bytes for username. 10/11/09 15:00:47: INFO: Sent 25 bytes for username. 10/11/09 15:00:47: INFO: Sending 30 bytes for password. 10/11/09 15:00:47: INFO: Sent 30 bytes for password. 10/11/09 15:00:48: INFO: Got line from MI->SUCCESS: 'Auth' username entered, but not yet verified 10/11/09 15:00:48: INFO: Got line from MI->SUCCESS: 'Auth' password entered, but not yet verified 10/11/09 15:00:48: INFO: Got line from MI->>STATE:1255287647,WAIT,,, 10/11/09 15:00:48: INFO: Got line from MI->>BYTECOUNT:0,42 10/11/09 15:00:48: INFO: Got line from MI->>BYTECOUNT:54,42 10/11/09 15:00:48: INFO: Got line from MI->>STATE:1255287648,AUTH,,, 10/11/09 15:00:50: INFO: Got line from MI->>BYTECOUNT:2560,2868 10/11/09 15:00:52: INFO: Got line from MI->>BYTECOUNT:2560,3378 10/11/09 15:00:54: INFO: Got line from MI->>BYTECOUNT:2560,3888 ... Is there anyway to turn on robust logging on the server to understand what is happening? Any ideas on how to hunt this down?

    Read the article

  • Router 2wire, Slackware desktop in DMZ mode, iptables policy aginst ping, but still pingable

    - by user135501
    I'm in DMZ mode, so I'm firewalling myself, stealthy all ok, but I get faulty test results from Shields Up that there are pings. Yesterday I couldn't make a connection to game servers work, because ping block was enabled (on the router). I disabled it, but this persists even due to my firewall. What is the connection between me and my router in DMZ mode (for my machine, there is bunch of others too behind router firewall)? When it allows router affecting if I'm pingable or not and if router has setting not blocking ping, rules in my iptables for this scenario do not work. Please ignore commented rules, I do uncomment them as I want. These two should do the job right? iptables -A INPUT -p icmp --icmp-type echo-request -j DROP echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all Here are my iptables: #!/bin/sh # Begin /bin/firewall-start # Insert connection-tracking modules (not needed if built into the kernel). #modprobe ip_tables #modprobe iptable_filter #modprobe ip_conntrack #modprobe ip_conntrack_ftp #modprobe ipt_state #modprobe ipt_LOG # allow local-only connections iptables -A INPUT -i lo -j ACCEPT # free output on any interface to any ip for any service # (equal to -P ACCEPT) iptables -A OUTPUT -j ACCEPT # permit answers on already established connections # and permit new connections related to established ones (eg active-ftp) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT #Gamespy&NWN #iptables -A INPUT -p tcp -m tcp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 6667 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 28910 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29900 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29901 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29920 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p udp -m udp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 6500 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27900 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27901 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 29910 -j ACCEPT # Log everything else: What's Windows' latest exploitable vulnerability? iptables -A INPUT -j LOG --log-prefix "FIREWALL:INPUT" # set a sane policy: everything not accepted > /dev/null iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP iptables -A INPUT -p icmp --icmp-type echo-request -j DROP # be verbose on dynamic ip-addresses (not needed in case of static IP) echo 2 > /proc/sys/net/ipv4/ip_dynaddr # disable ExplicitCongestionNotification - too many routers are still # ignorant echo 0 > /proc/sys/net/ipv4/tcp_ecn #ping death echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all # If you are frequently accessing ftp-servers or enjoy chatting you might # notice certain delays because some implementations of these daemons have # the feature of querying an identd on your box for your username for # logging. Although there's really no harm in this, having an identd # running is not recommended because some implementations are known to be # vulnerable. # To avoid these delays you could reject the requests with a 'tcp-reset': #iptables -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset #iptables -A OUTPUT -p tcp --sport 113 -m state --state RELATED -j ACCEPT # To log and drop invalid packets, mostly harmless packets that came in # after netfilter's timeout, sometimes scans: #iptables -I INPUT 1 -p tcp -m state --state INVALID -j LOG --log-prefix \ "FIREWALL:INVALID" #iptables -I INPUT 2 -p tcp -m state --state INVALID -j DROP # End /bin/firewall-start

    Read the article

  • File server share access intermittent/slow/machine unstable: win2k8r2

    - by Jack B.
    I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

    Read the article

  • NPM not installing dependencies?

    - by neezer
    Having trouble getting NPM to install dependencies with npm install -d in my project directory with a defined package.json file. Here's my package.json: https://gist.github.com/3068312 And after wiping my project root's node modules folder (rm -rf node_modules), I run npm install -d in my project root and am greeted with this: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm http GET https://registry.npmjs.org/sinon npm http GET https://registry.npmjs.org/underscore npm http GET https://registry.npmjs.org/mocha npm http GET https://registry.npmjs.org/request npm http 304 https://registry.npmjs.org/sinon npm http 304 https://registry.npmjs.org/underscore npm http 304 https://registry.npmjs.org/mocha npm http 304 https://registry.npmjs.org/request npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info unbuild /vagrant/node_modules/underscore npm info unbuild /vagrant/node_modules/mocha npm info unbuild /vagrant/node_modules/sinon npm info unbuild /vagrant/node_modules/request npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/underscore npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/underscore' npm ERR! Error: ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! You may report this log at: npm ERR! <http://bugs.debian.org/npm> npm ERR! or use npm ERR! reportbug --attach /vagrant/npm-debug.log npm npm ERR! npm ERR! System Linux 3.2.0-23-generic npm ERR! command "node" "/usr/bin/npm" "install" "-d" npm ERR! cwd /vagrant npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! path /vagrant/node_modules/underscore/package.json npm ERR! code ENOENT npm ERR! message ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! errno {} npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/request npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/request' npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /vagrant/npm-debug.log npm not ok If I rerun npm install -d, the error changes to whatever the next package is... if I keep running it it over and over again, it eventually doesn't complain anymore and outputs: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm info build /vagrant npm info linkStuff [email protected] npm info install [email protected] npm info postinstall [email protected] npm info ok However, none of the dependencies for any of these packages get installed. For instance, cheerio has a few dependencies, so when I try running my test suite, I'm greeted with: (ssh) /vagrant git:master ? mocha --compilers coffee:coffee-script --watch spec/* node.js:201 throw e; // process.nextTick error, or 'error' event on first tick ^ Error: Cannot find module 'cheerio-select' at Function._resolveFilename (module.js:332:11) at Function._load (module.js:279:25) at Module.require (module.js:354:17) What gives? I'm on Ubuntu Precise64 in a Vagrant virtual box.

    Read the article

  • how to troubleshoot using rsyslog to output to a mysql database

    - by ChrisNZ
    Using FreeBSD 8.0 32 bit. I have installed rsyslogd 5.5.5 with ommysql. (installed ports /usr/ports/sysutils/rsyslog55 and /usr/ports/sysutils/rsyslog55-mysql) My rsyslog.conf file looks like: $ModLoad imudp $ModLoad imtcp $ModLoad ommysql $ModLoad immark.so $ModLoad imuxsock.so $ModLoad imklog.so $OptimizeForUniprocessor on $AllowedSender UDP, 10.0.0.0/8 $UDPServerAddress 0.0.0.0 $UDPServerRun 514 $UDPServerTimeRequery 2 # +SG560 *.* :ommysql:127.0.0.1,Syslog,sysloguser,mypassword My command line flags for rsyslogd are: -c5 -4 Checking the code with -c5 -N1 returns no errors. I have confirmed that rsyslogd is working by changing the last line to say: *.* /var/log/snapgear.log which results in messages appearing in the snapgear.log file. So it is probably something to do with my MySQL setup If I do: mysql -u sysloguser -p Syslog Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 56 Server version: 5.0.86 FreeBSD port: mysql-server-5.0.86 mysql> select * from SystemEvents; Empty set (0.00 sec) mysql> :-( I have confirmed that sysloguser has full privileges for the Syslog database. If I run rsyslogd on the console in debug mode: /usr/local/sbin/rsyslogd -f /usr/local/etc/rsyslog.conf -c5 -n -d I can see this sequence of events each time a message is received: 9244.376687256:28359280: main Q: entry added, size now log 1, phys 1 entries 9244.376705694:28359280: main Q: EnqueueMsg advised worker start 9244.376726647:28359280: Listening on UDP syslogd socket 4 (IPv4/port 514). 9244.376728602:28359280: --------imUDP calling select, active file descriptors (max 4): 4 9244.376890075:283593c0: wti 0x28306e80: worker awoke from idle processing 9244.376892031:283593c0: we deleted 0 objects and enqueued 0 objects 9244.376893986:283593c0: delete batch from store, new sizes: log 1, phys 1 9244.376895942:283593c0: msgConsumer processes msg 0/1 9244.376897898:283593c0: msg parser: flags 70, from '~NOTRESOLVED~', msg 'Jun 29 17:32:24 SG560 kernel: (20000629T1732244' 9244.376900132:283593c0: parse using parser list 0x283080e8 (the default list). 9244.376902088:283593c0: dropped LF at very end of message (DropTrailingLF is set) 9244.376904044:283593c0: Parser 'rsyslog.rfc5424' returned -2160 9244.376905999:283593c0: Message will now be parsed by the legacy syslog parser (one size fits all... ;)). 9244.376907955:283593c0: Parser 'rsyslog.rfc3164' returned 0 9244.376909910:283593c0: testing filter, f_pmask 255 9244.376911866:283593c0: Called action, logging to ommysql 9244.376918012:283593c0: actionTryResume: action state: susp, next retry (if applicable): 1277869250 [now 1277869244] 9244.376919967:283593c0: action call returned -2123 9244.376921923:283593c0: tryDoAction: unexpected error code -2123, finalizing 9244.376926113:283593c0: actionTryResume: action state: susp, next retry (if applicable): 1277869250 [now 1277869244] 9244.376928069:283593c0: ruleset: get iRet 0 from rule.ProcessMsg() 9244.376930024:283593c0: ruleset.ProcessMsg() returns 0 9244.376931980:283593c0: regular consumer finished, iret=0, szlog 0 sz phys 1 9244.376933936:283593c0: XXX: enqueueing data element 0 of 1 9244.376935891:283593c0: we deleted 1 objects and enqueued 0 objects 9244.376938126:283593c0: delete batch from store, new sizes: log 0, phys 0 9244.376940082:283593c0: regular consumer finished, iret=4, szlog 0 sz phys 0 9244.376942037:283593c0: main Q:Reg/w0: worker IDLE, waiting for work. .... I can see the Action Call to ommysql returns unexpected error code -2123 Now I am stuck! Any ideas on what to look for next? Perhaps I there are extra ports I need to install? I will be very grateful for any assistance here!

    Read the article

  • phpMyAdmin setup issues

    - by EquinoX
    I am trying to follow the tutorial here to setup the user and pass. It says there that "this section is only applicable if your MySQL server is running with --skip-show-database". First question is, how do I check if MySQl server is running with --skip-show-database? Is there any way I can access phpMyAdmin SQL query window without logging in? Otherwise I'd have to execute this SQL from command line. I am also getting this: Cannot load mcrypt extension. Please check your PHP configuration. I have added mcrypt.so to php.ini and doing the following command proves that I have it. [root@DT html]# rpm -qa | grep mcrypt mcrypt-2.6.8-1.el5 php-mcrypt-5.3.5-1.1.w5 libmcrypt-2.5.8-4.el5.centos [root@DT html]# php -v PHP 5.3.5 (cli) (built: Feb 19 2011 13:10:09) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies Now when I go to phpinfo() and search for mcrypt it can find it inside the Configure Command row ('--with-mcrypt=shared,/usr'). So, what to do next?. UPDATE: I didn't put extension=mcrypt.so in php.ini as it will complain the following: PHP Warning: Module 'mcrypt' already loaded in Unknown on line 0 Here's my nginx.conf: #user nobody; worker_processes 2; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; gzip on; server { listen 80; root /usr/share/nginx/html; server_name localhost; #charset koi8-r; #access_log logs/host.access.log main; location / { #root html; index index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { #root html; } # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { #root /usr/local/nginx/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/nginx/html$fastcgi_script _name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { # listen 8000; # listen somename:8080; # server_name somename alias another.alias; # location / { # root html; # index index.html index.htm; # } #} # HTTPS server # #server { # listen 443; # server_name localhost; # ssl on; # ssl_certificate cert.pem; # ssl_certificate_key cert.key; # ssl_session_timeout 5m; # ssl_protocols SSLv2 SSLv3 TLSv1; # ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; # ssl_prefer_server_ciphers on; # location / { # root html; # index index.html index.htm; # } #} }

    Read the article

  • VPS 512 MB RAM with WordPressMU comes to consumes lots of memory

    - by CAPitalZ
    I have googled for days and gathered all optimization suggestions and tried. My sites are not getting any high hits. May be like 100 hits per day [all my sites combined]. Here are my specs I have 512 MB RAM VPS with burstable 1024 MB. Centos 5 32-bit & cPanel/WHM Apache 2.2 MySQL 5.0 PHP 5.3.2 Here is my Configs I have 2 WordPressMU production sites, and 1 test site my.cnf # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/lib/mysql/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking skip-bdb skip-innodb key_buffer = 16M max_allowed_packet = 1M table_cache = 64 sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M #CAPitalZ thread_cache_size=8 thread_concurrency=4 #query_cache_type=1 #query_cache_limit=1M query_cache_size=16M concurrent_insert=2 low_priority_updates=1 max_connections=50 tmp_table_size=16M max_heap_table_size=16M join_buffer_size=1M interactive_timeout=25 wait_timeout=1000 #connect_timout=10 not able to restart mysql max_connect_errors=10 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # skip-networking # Disable Federated by default skip-federated # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 [mysqld_safe] open_files_limit=8192 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [myisamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout httpd.conf I have unselected many modules and recompiled using EasyApache in WHM. Only have the following modules built Deflate Expires Fileprotect Imagemap MPM Prefork Version [default] EAccelerator for PHP Bcmath Calendar CurlSSL [I'm using Curl. But I don't have any https sites] Expat GD [for image cropping] Gettext Imap Mbregex [default] Mbstring [need both Mbregex and Mbstring for utf-8] Mysql of the system MySQL "Improved" extension. Sockets TTF (FreeType) [I'm using custom font] Zlib Under Global Configuration I only have FollowSymLinks enabled I Have TraceEnable, ServerSignature, FileETag OFF ServerTokens ProductOnly DirectoryIndex Priority has index.php as the first one I have removed Clamd [Clam Anti-virus] SpamAssasin is Off Under Tweak Settings Default catch-all/default address behavior for new accounts. This is set to "fail" All stats programs turned off I have eAccelerator installed and checked in phpinfo and its working [Pre VirtualHost Include under WHM] Timeout 20 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 3 MinSpareServers 1 MaxSpareServers 3 StartServers 1 ServerLimit 50 MaxClients 50 MaxRequestsPerChild 4000 ExtendedStatus Off #ServerType standalone this throws error HostnameLookups Off <Directory "/"> AllowOverride None </Directory> My sites will take ages to load and WHM/CPanel will not even load. adadaa.com/ http://adadaa.net/ kadais.ca/ My average memory consumption is like 1000 MB! [yes always bursting] The process that consumes most CPU and also most memory is mysql But I also get like 15 httpd processes [when its bursting] I already got warning from cpuwatchcheck saying "While processing, the cpu has been maxed out for more than a 6 hour period. The current load/uptime line on the server at the time of this email is 07:00:37 up 11:30, 0 users, load average: 14.64, 16.79, 20.07" I don't know, I have tried switching these config values many different times, but nothing seems to work. Please show some light... Thanks

    Read the article

  • got VPN l2l connect between a site & HQ but not traffice using ASA5505 on both ends

    - by vinlata
    Hi, Could anyone see what did I do wrong here? this is one configuration of site1 to HQ on ASA5505, I can get connected but seems like no traffic going (allowed) between them, could it be a NAT issue? any helps would much be appreciated Thanks interface Vlan1 nameif inside security-level 100 ip address 172.30.205.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address pppoe setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 shutdown ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! passwd .dIuXDIYzD6RSHz7 encrypted ftp mode passive dns server-group DefaultDNS domain-name errg.net object-group network HQ network-object 172.22.0.0 255.255.0.0 network-object 172.22.0.0 255.255.128.0 network-object 172.22.0.0 255.255.255.128 network-object 172.22.1.0 255.255.255.128 network-object 172.22.1.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_20_cryptomap extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list inside_nat0_outbound extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list policy-nat extended permit ip 172.30.205.0 255.255.255.0 172.22.0.0 255.255.0.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) 172.30.205.0 access-list policy-nat access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute username errgadmin password Os98gTdF8BZ0X2Px encrypted privilege 15 http server enable http 64.42.2.224 255.255.255.240 outside http 172.22.0.0 255.255.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 190 match address outside_20_cryptomap crypto map outside_map 190 set pfs crypto map outside_map 190 set peer 66.7.249.109 crypto map outside_map 190 set transform-set ESP-3DES-SHA crypto map outside_map 190 set phase1-mode aggressive crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 190 crypto isakmp ipsec-over-tcp port 10000 tunnel-group 66.7.249.109 type ipsec-l2l tunnel-group 66.7.249.109 ipsec-attributes pre-shared-key * telnet timeout 5 ssh 172.30.205.0 255.255.255.0 inside ssh 172.22.0.0 255.255.0.0 outside ssh 64.42.2.224 255.255.255.240 outside ssh 172.25.0.0 255.255.128.0 outside ssh timeout 5 console timeout 0 management-access inside vpdn group PPPoEx request dialout pppoe vpdn group PPPoEx localname [email protected] vpdn group PPPoEx ppp authentication pap vpdn username [email protected] password ********* dhcpd address 172.30.205.100-172.30.205.131 inside dhcpd dns 172.22.0.133 68.94.156.1 interface inside dhcpd wins 172.22.0.133 interface inside dhcpd domain errg.net interface inside dhcpd enable inside ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! end

    Read the article

  • amplified reflected attack on dns

    - by Mike Janson
    The term is new to me. So I have a few questions about it. I've heard it mostly happens with DNS servers? How do you protect against it? How do you know if your servers can be used as a victim? This is a configuration issue right? my named conf file include "/etc/rndc.key"; controls { inet 127.0.0.1 allow { localhost; } keys { "rndc-key"; }; }; options { /* make named use port 53 for the source of all queries, to allow * firewalls to block all ports except 53: */ // query-source port 53; /* We no longer enable this by default as the dns posion exploit has forced many providers to open up their firewalls a bit */ // Put files that named is allowed to write in the data/ directory: directory "/var/named"; // the default pid-file "/var/run/named/named.pid"; dump-file "data/cache_dump.db"; statistics-file "data/named_stats.txt"; /* memstatistics-file "data/named_mem_stats.txt"; */ allow-transfer {"none";}; }; logging { /* If you want to enable debugging, eg. using the 'rndc trace' command, * named will try to write the 'named.run' file in the $directory (/var/named"). * By default, SELinux policy does not allow named to modify the /var/named" directory, * so put the default debug log file in data/ : */ channel default_debug { file "data/named.run"; severity dynamic; }; }; view "localhost_resolver" { /* This view sets up named to be a localhost resolver ( caching only nameserver ). * If all you want is a caching-only nameserver, then you need only define this view: */ match-clients { 127.0.0.0/24; }; match-destinations { localhost; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; /* these are zones that contain definitions for all the localhost * names and addresses, as recommended in RFC1912 - these names should * ONLY be served to localhost clients: */ include "/var/named/named.rfc1912.zones"; }; view "internal" { /* This view will contain zones you want to serve only to "internal" clients that connect via your directly attached LAN interfaces - "localnets" . */ match-clients { localnets; }; match-destinations { localnets; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; // include "/var/named/named.rfc1912.zones"; // you should not serve your rfc1912 names to non-localhost clients. // These are your "authoritative" internal zones, and would probably // also be included in the "localhost_resolver" view above :

    Read the article

  • I have a NGINX server configured to work with node.js, but many times a file of 1.03MB of js is not loaded by various browser and various pc

    - by Totty
    I'm using this in a local LAN so it should be quite fast. The nginx server use the node.js server to serve static files, so it must pass throught node.js to download the files, but that is not a problem when I'm not using the nginx. In chrome with debugger on I can see that the status is: 206 - partial content and it only has downloaded 31KB of 1.03MB. After 1.1 min it turns red and the status failed. Waiting time: 6ms Receiving: 1.1 min The headers in google chrom: Request URL:http://192.168.1.16/production/assembly/script/production.js Request Method:GET Status Code:206 Partial Content Request Headersview source Accept:*/* Accept-Charset:ISO-8859-1,utf-8;q=0.7,*;q=0.3 Accept-Encoding:gzip,deflate,sdch Accept-Language:pt-PT,pt;q=0.8,en-US;q=0.6,en;q=0.4 Connection:keep-alive Cookie:connect.sid=s%3Abls2qobcCaJ%2FyBNZwedtDR9N.0vD4Fi03H1bEdCszGsxIjjK0lZIjJhLnToWKFVxZOiE Host:192.168.1.16 If-Range:"1081715-1350053827000" Range:bytes=16090-16090 Referer:http://192.168.1.16/production/assembly/ User-Agent:Mozilla/5.0 (Windows NT 6.0) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.94 Safari/537.4 Response Headersview source Accept-Ranges:bytes Cache-Control:public, max-age=0 Connection:keep-alive Content-Length:1 Content-Range:bytes 16090-16090/1081715 Content-Type:application/javascript Date:Mon, 15 Oct 2012 09:18:50 GMT ETag:"1081715-1350053827000" Last-Modified:Fri, 12 Oct 2012 14:57:07 GMT Server:nginx/1.1.19 X-Powered-By:Express My nginx configurations: File 1: user totty; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /home/totty/web/production01_server/node_modules/production/_logs/_NGINX_access.txt; error_log /home/totty/web/production01_server/node_modules/production/_logs/_NGINX_error.txt; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## autoindex on; include /home/totty/web/production01_server/_deployment/nginxConfigs/server/*; } File that is included by the previous file: server { # custom location for entry # using only "/" instead of "/production/assembly" it # would allow you to go to "thatip/". In this way # we are limiting to "thatip/production/assembly/" location /production/assembly/ { # ip and port used in node.js proxy_pass http://127.0.0.1:3000/; } location /production/assembly.mongo/ { proxy_pass http://127.0.0.1:9000/; proxy_redirect off; } location /production/assembly.logs/ { autoindex on; alias /home/totty/web/production01_server/node_modules/production/_logs/; } }

    Read the article

  • Can spliting an access database cause printer and reporting issues?

    - by leeand00
    We have a setup in which our users log into an access database using MS Access 2003 over an RDP connection. The user's login to their own machines first using a roaming profile. They then click an rdp connection file on the desktop and login to the remote server, via RDP, where they use MS Access as the shell; they don't have any access to any of explorer.exe features such as the start menu. The database they are logging into is more of an application, and provides functionality for entering data, querying data, and running reports via form based menus. It all worked pretty well until we split the database as it was nearing 2GBs in size. We moved out the payroll data into a separate partition, a database with the same name in a different folder, both of them on the server. Only two tables were moved into this new database partition, and they were re-linked as external tables in the new partition. Now while everything appears to be working fine data-wise after the split, there's a new issue when our users login via RDP and attempt to run reports: often the report will not display and instead the user sees an error about the click event of the form. At first I didn't even know it was printer-related, as we didn't really change anything related to the printers as far as I knew. Confused about the error, I talked to the guy who previously worked here and who was in charge of splitting the database, and he told me to tell the users to set their default printers (on their local machines, not on the server) to the "printer" Microsoft XPS Document Writer which isn't a physical printer at all. This allowed the user's to display their reports, but if they want to print out reports, they are required to go to the File menu and select Print, clicking the print icon on the toolbar takes them to a Save As... dialog as would be expected when using the Microsoft XPS Document Writer as your default printer. It's easy to tell if the user is having a problem because a quick mouseover of the printer icon will yield a tooltip of (none) when they cannot access their reports, and a tooltip of Microsoft XPS Document Writer when they can view the reports. If the user's printer is set to anything other than Microsoft XPS Document Writer as the default on their local machine, then (none) is always displayed when they rdp to the database. The RDP settings are setup to transfer the local printer to the server. Telling the users to do this to print has been more of a band-aid on the whole situation until we find a better solution and an explanation as to why splitting a database would prevent users from printing or even viewing access database reports. Which is why I'm here asking this question. Also of note all the printers on the network now show up on the server so that when the users do click File->Print to print their reports on a physical printer, they have to look through a huge list of printers to find theirs in the dropdown. So the little band-aid fix we have is not ideal. Previously, only the printers on the user's local machine displayed here, and not all the printers on the network. My co-worker seems to think this has something to do with permissions, I personally think it has to do with roaming profiles, and Group Policies which is what I've been reading up on. I really don't know how to fix this or how it is related to splitting the database.

    Read the article

  • File server share access intermittent/slow/machine unstable: win2k8r2

    - by Jack B.
    I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

    Read the article

  • Optimise Apache for EC2 micro instance

    - by Shiyu Sekam
    I'm running apache2 on a EC2 micro instance with ~600 mb RAM. The instance was running for almost a year without problems, but in the last weeks it just keeps crashing, because the server reached MaxClients. The server basically runs few websites, one wordpress blog(not often used), company website(most used) and 2 small sites, which are just internal. The database for the blog runs on RDS, so there's no Mysql running on this web server. When I came to the company, the server already was setup and is running apache + mod_php + prefork. We want to migrate that in the future to a nginx + php-fpm, but it still needs further testing. So for now I have to stick with the old setup. I also use CloudFlare DDOS protection in front of the server, because it was attacked a couple of the times in the last weeks. My company don't want to pay money for a better web server at this point, so I have to stick with the micro instance also. Additionally the code for the website we run is really bad and slow and sometimes a single page load can take up to 15 seconds. The whole website is dynamic and written in PHP, so caching isn't really an option here. It's a customized search for users. I've already turned off KeepAlive, which improved the performance a little bit. My prefork config looks like the following: StartServers 2 MinSpareServers 2 MaxSpareServers 5 ServerLimit 10 MaxClients 10 MaxRequestsPerChild 100 The server just becomes unresponsive after a while running and I've run the following command to see how many connections there are: netstat | grep http | wc -l 75 Trying to restart apache helps for a short moment, but after that a while the apache process(es) become unresponsive again. I've the following modules enabled(output of apache2ctl -M) Loaded Modules: core_module (static) log_config_module (static) logio_module (static) version_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) authz_host_module (shared) deflate_module (shared) dir_module (shared) expires_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK apache2.conf # Security ServerTokens OS ServerSignature On TraceEnable On ServerName "web.example.com" ServerRoot "/etc/apache2" PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive off User www-data Group www-data AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> <Directory /> Options FollowSymLinks AllowOverride None </Directory> DefaultType none HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel warn EnableSendfile On #Listen 80 Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf Include /etc/apache2/ports.conf LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include /etc/apache2/conf.d/*.conf Include /etc/apache2/sites-enabled/*.conf Vhost of main site <VirtualHost *:80> ServerName www.example.com ## Vhost docroot DocumentRoot /srv/www/jenkins/Web ## Directories, there should at least be a declaration for /srv/www/jenkins/Web <Directory /srv/www/jenkins/Web> AllowOverride All Order allow,deny Allow from all </Directory> ## Load additional static includes ## Logging ErrorLog /var/log/apache2/www.example.com.error.log LogLevel warn ServerSignature Off CustomLog /var/log/apache2/www.example.com.access.log combined ## Rewrite rules RewriteEngine On RewriteCond %{HTTP_HOST} !^www.example.com$ RewriteRule ^.*$ http://www.example.com%{REQUEST_URI} [R=301,L] ## Server aliases ServerAlias www.example.invalid ServerAlias example.com ## Custom fragment <Location /srv/www/jenkins/Web/library> Order Deny,Allow Deny from all </Location> <Files ~ "^\.(.+)"> Order deny,allow deny from all </Files> </VirtualHost>

    Read the article

  • File server share access intermittent/slow/machine unstable: win2kr2

    - by Jack B.
    I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

    Read the article

  • Lockdown users on Windows Server 2012

    - by el.severo
    I set up a Active Directory on a server machine with Windows Server 2012 and I'd like to create some users with limitations like Windows Steady State does in Windows XP (locally). Seen already the Windows SteadyState Handbook (with Windows Server 2008), but I'd like to know if anyone has tried this before, the limitations are the following: 1. Prevent locked or roaming user profiles that cannot be found on the computer from logging on 2. Do not cache copies of locked or roaming user profiles for users who have previously logged on to this computer 3. Do not allow Windows to compute and store passwords using LAN Manager Hash values 4. Do not store usernames or passwords used to log on to the Windows Live ID or the domain 5. Prevent users from creating folders and files on drive C:\ 6. Lock profile to prevent the user from making permanent changes 7. Remove the Control Panel, Printer and Network Settings from the Classic Start menu 8. Remove the Favorites icon 9. Remove the My Network Places icon 10. Remove the Frequently Used Program list 11. Remove the Shared documents folder from My Computer 12. Remove control Panel icon 13. Remove the Set Program Access and Defaults icon 14. Remove the Network Connection(Connect To)icon 15. Remove the Printers and Faxes icon 16. Remove the Run icon 17. Prevent access to Windows Explorer features: Folder Options, Customize Toolbar, and the Notification Area 18. Prevent access to the taskbar 19. Prevent access to the command prompt 20. Prevent access to the registry editor 21. Prevent access to the Task Manager 22. Prevent access to Microsoft Management Console utilities 23. Prevent users from adding or removing printers 24. Prevent users from locking the computer 25. Prevent password changes (also requires the Control Panel icon to be removed) 26. Disable System Tools and other management programs 27. Prevent users from saving files to the desktop 28. Hide A Drive 29. Hide B Drive 30. Hide C Drive 31. Prevent changes to Internet Explorer registry settings 32. Empty the Temporary Internet Files folder when Internet Explorer is closed 33. Remove Internet Options 34. Remove General tab in Internet Options 35. Remove Security tab in Internet Options 36. Remove Privacy tab in Internet Options 37. Remove Content tab in Internet Options 38. Remove Connections tab in Internet Options 39. Remove Programs tab in Internet Options 40. Remove Advanced tab in Internet Options 41. Set a home page (Internet Explorer) 42. Restrict the possibility to change desktop image 43. Restrict the possibility to change wallpaper 44. Restrict usb flash drives Any suggestions for this? UPDATE: As @Dan suggested me I'd like to specify that would be applied to a educational scenario where students can login from a computer and want to add some restrictions to them.

    Read the article

  • I am getting a 400 Bad Request error when using Nginx and PHP-FPM, why?

    - by Bob
    I am trying to run a website (that requires PHP - it technically doesn't require MySQL at this time, but it may sometime in the near future as I continue developing it, so I went ahead and installed that as well) using nginx 1.2.4 and PHP-FPM 5.3.3 on Ubuntu 12.04.1 LTS. As far as I know, I haven't done anything wrong, but clearly something is not quite right - I seem to be getting a 400 Bad Request error whenever I try to browse to my website. I've been mostly following one guide, and I've done more or less everything it recommends, except for not setting up PHP-FPM to use a Unix Socket and I used service as opposed to /etc/init.d/ when starting/stopping nginx, PHP, and MySQL. Anyways, here are my relevant configuration files (I have only censored personal/sensitive details, like my domain name - which contains my real name): /etc/nginx/nginx.conf user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 15; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } /etc/nginx/sites-enabled/subdomain.mydomain.net server { listen 80; # listen for IPv4 listen [::]:80; # listen for IPv6 server_name www.subdomain.mydomain.net subdomain.mydomain.net; access_log /srv/www/subdomain.mydomain.net/logs/access.log; error_log /srv/www/subdomain.mydomain.net/logs/error.log; location / { root /srv/www/subdomain.mydomain.net/public; index index.php; } location ~ \.php$ { try_files $uri =400; include fastcgi_params; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/subdomain.mydomain.net/public$fastcgi_script_name; } } All the directories listed in the configuration files above are correct on my server (to the extent of my knowledge). I have not included /etc/php5/fpm/pool.d/www.conf or /etc/php5/fpm/php.ini in this post as they're rather long, but I have posted them on Pastebin: http://pastebin.com/ensErJD8 and http://pastebin.com/T23dt7vM, respectively. Although, the only thing I've changed in either of the two files was in php.ini, where I set expose_php to off so as to hide the .php file extension from users. What can I do to resolve my issue? Please let me know if I need to supply any additional details.

    Read the article

  • Monitor randomly shutting down, computer accepting no input, need to restart to get working

    - by Sebastian Lamerichs
    First off, spec list: OS: Windows 7 Ultimate 64-bit SP1 CPU: i7-4820k @ 3.7GHz (stock) GPU: Two 3GB Radeon HD 7970s @ 1.05GHz Mobo: AsRock X79 Extreme6 HDD: 2TB Seagate Barracuda 7200rpm RAM: 16GB quad-channel Kingston 1600MHz PSU: Antec HCG 900W Monitors: Acer S220HQL 1920x1080 + ViewSonic VA2251 1920x1080. Plugged into different GPUs. My problem is that, on a daily-ish basis, my monitors will turn off and not turn back on. My computer will still be running, GPU/CPU/case fans all still going, but the monitors will not turn back on. Additionally, it seems to cease all network activity. It doesn't seem to log any errors at all. I've verified that this is not a monitor issue, as when I press the num/caps/scroll lock buttons on my keyboard, the lights don't change, so the computer is clearly not accepting input. I have noticed a few other people on the internet with this problem, and some have claimed that it was solved by disabling PCI-Express Link State Power Management, but the issue still occurs for me after this. Whilst my CPU and GPUs both run at 100% 24/7, the temperatures are certainly not at dangerous levels, with the CPU averaging 65°C and the GPUs at 70°C and 78°C average. All components are brand new. I have tried forcing MSI Afterburner to start when Windows starts and to force a constant voltage, as this fixed the issue for a few days for another user, but he reported back saying that it had stopped working properly again, so I'm not putting too much faith in this working. Many people have said to adjust display sleep mode settings, but this will clearly not work, as the keyboard lights would still work if the monitors were the issue. The closest I can get to a log file for this issue is the following Folding@Home logs: 14:45:21:WU01:FS00:0x17:Completed 1120000 out of 2000000 steps (56%) 14:46:43:WU00:FS01:0x17:Completed 480000 out of 2000000 steps (24%) 14:46:49:WU01:FS00:0x17:Completed 1140000 out of 2000000 steps (57%) 14:48:30:WU01:FS00:0x17:Completed 1160000 out of 2000000 steps (58%) 14:49:55:WU01:FS00:0x17:Completed 1180000 out of 2000000 steps (59%) As you can see, the second GPU (FS01) stops computation approximately three and a half minutes before the issue occurs (it should be completing 1% every 80-120 seconds), and the first GPU (FS00) continues for a few minutes more before the logs just end. As far as I can tell, the computer has a network failure at the time the first GPU stops working, the latest IRC message I received from this time was at 14:47:58. That being said, there could have just not been any messages between then and 14:50:00, so I'm going to be connecting a laptop to the same bouncer to double-check if it happens again. The GPUs functioned perfectly well in another computer for a significant period of time, so I'm fairly confident that they aren't the issue, which means that this is being caused by either software or the motherboard, or possibly RAM. I really hope it's software. I heard from a forum board that there was a patch from Microsoft that fixed this problem, but "I've forgot which KB it was or the google search terms I used to find the patch, LOL.", so that's not much help. Haven't seen it mentioned by anyone else on about a dozen threads about this issue either. The computer is plugged in via a surge-protected power board, and I've run several other computers and pieces of hardware through it with no issues, so that is not the cause. I have just set the hard disk to never turn off, although I don't believe that that will solve the issue. Strangely, this has only happened when I'm not at the computer (which is actually a minority of the time). Until today it had only happened when I had not been actively using the computer for 6 hours, but today it happened within 10-30 minutes of me last using the computer actively. I have enabled file logging from MSI Afterburner, so hopefully this will shed some light on the issue, but I'm not too optimistic. I've heard that it could be a motherboard problem, but I figured I should ask around before RMAing it. Any help?

    Read the article

  • BIND no longer responds to AXFR Requests

    - by djsumdog
    Recently we moved our primary external DNS server. It has three caching DNS slaves in front of it provided by our ISP. They've told us they've started getting access denied requests when doing zone transfers (AXFR). If I add in my own IPs to the allow-transfer list, I also get a transfer failed when using dig with the AXFR argument. Here is what my bind configuration looks like: options { directory "/var/lib/named"; dump-file "/var/log/named_dump.db"; zone-statistics yes; statistics-file "/var/log/named.stats"; listen-on-v6 { any; }; notify-source 10.19.0.68 port 53; querylog yes; notify yes; allow-transfer { 127.0.0.1; //localhost 1.1.1.1; //public dns slave 1 2.2.2.2; //public dns slave 2 3.3.3.3; //public dns slave 3 }; also-notify { 1.1.1.1; //public dns slave 1 2.2.2.2; //public dns slave 2 3.3.3.3; //public dns slave 3 }; include "/etc/named.d/forwarders.conf"; }; logging { channel simple_log { file "/var/log/bind.log" versions 10 size 3m; severity info; print-time yes; print-severity yes; print-category yes; }; category default{ simple_log; }; channel log_zone_transfers { file "/var/log/axfr.log" versions 10 size 3m; print-time yes; print-category yes; print-severity yes; }; category xfer-out { log_zone_transfers; }; channel log_notify { file "/var/log/notify.log" versions 10 size 3m; print-time yes; print-category yes; print-severity yes; }; category notify { log_notify; }; channel queries { file "/var/log/queries.log" versions 10 size 30m; print-time yes; severity info; print-category yes; print-severity yes; }; category queries { queries; }; }; zone "." in { type hint; file "root.hint"; }; zone "localhost" in { type master; file "localhost.zone"; }; zone "0.0.127.in-addr.arpa" in { type master; file "127.0.0.zone"; }; include "/etc/named.conf.include"; zone "example.net " { type master; file "/var/lib/named/master/example.net.hosts"; }; zone "example.com " { type master; file "/var/lib/named/master/example.com.hosts"; }; ## -- other master files -- And the errors in the xfer log look like the following: 29-Oct-2012 14:20:02.806 xfer-out: info: client 1.1.1.1#59069: bad zone transfer request: 'example.com./IN': non-authoritative zone (NOTAUTH) I've tried adding allow-transfer parameters directly on the zone files and still get failed transfers. Any idea what I'm doing wrong?

    Read the article

  • Flat File Connection Manager in SSIS package shows "Valid File Name Must be Selected"

    - by Traples
    (Flat File Location) Samba Share | Windows Share (SSIS) _______________________________ | | XP 32bit | Works | Works | | 2003 Serv 32bit | Works | Works | | Vista 64bit | ERROR | Works | | Win 7 64bit | ERROR | Works | | 2008 Serv 64bit | ERROR | Works I created an SSIS package in VS 2008 that parses a flat file from a shared folder and puts the records into a SQL Server db. I recently installed Windows 7 and VS 2008 on a new workstation. When I import the package from TFS and open it, I get the error Validation error. Parse and Import Catalog Flat File: MySSISPackage: The file name "\\shared\flatfile.txt" specified in the connection was not valid. When I open the Flat File Connection Manager Editor, there is an error stating: A valid file name must be selected I can browse to and select the file from inside the editor, but I cannot change any properties, or move away from the General tab because of this error. If I go back to my laptop (Windows XP), where the package was first created, there is no error. Both workstations are on the same domain, and I'm logging in using the same credentials. Any ideas as to why I would receive this error from one workstation and not another? UPDATE: If I take the .dtsx package from the running workstation and load it into SSIS on the server, I get the following errors when it tries to run: Error: The file name "\\shared\flatfile.txt" specified in the connection was not valid. and... Error: Connection "MySSISPackage" failed validation. and... Error: The file name property is not valid. The file name is a device or contains invalid characters. UPDATE 2: a) The Shared folder I'm trying to pull the flat file from is a Samba share on a Unix box. b) If I access the file using SSIS on any 64-bit platform (Windows 7 64-bit, Vista 64-bit, Windows Server 2008) I get the error "A valid file name must be selected." c) Accessing the file using SSIS from 32-bit environments (Windows XP 32-bit, Windows Server 2003 32-bit) there is no problem. d) If I move the file to a shared folder on a Windows server, 64-bit SSIS recognizes the file.

    Read the article

  • Spring 3.0: Unable to locate Spring NamespaceHandler for XML schema namespace

    - by Nick Hristov
    My setup is fairly simple: I have a web front-end, back-end is spring-wired. I am using AOP to add a layer of security on my rpc services. It's all good, except for the fact that the web app aborts on launch: [java] SEVERE: Context initialization failed [java] org.springframework.beans.factory.parsing.BeanDefinitionParsingException: Configuration problem: Unable to locate Spring NamespaceHandler for XML schema namespace [http://www.springframework.org/schema/aop] [java] Offending resource: ServletContext resource [/WEB-INF/gwthandler-servlet.xml] Here is the snippet from my xml config file: <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:aop="http://www.springframework.org/schema/aop" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans.xsd http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop.xsd"> <aop:config> <aop:aspect id="security" ref="securityAspect" > <aop:pointcut id="securedServices" expression="@annotation(com.fb.boog.common.aspects.Secured)"/> <aop:before method="checkSecurity" pointcut-ref="securedServices"/> </aop:aspect> </aop:config> I read over the internets that it may be my classloading the core of the problem. Doubtful, since here is my WEB-INF/lib directory: ./WEB-INF/lib ./WEB-INF/lib/aopalliance-alpha1.jar ./WEB-INF/lib/aspectj-1.6.6.jar ./WEB-INF/lib/commons-collections.jar ./WEB-INF/lib/commons-logging.jar ./WEB-INF/lib/ehcache-core-1.7.0.jar ./WEB-INF/lib/ejb3-persistence.jar ./WEB-INF/lib/hibernate ./WEB-INF/lib/hibernate/antlr.jar ./WEB-INF/lib/hibernate/asm.jar ./WEB-INF/lib/hibernate/bsh-2.0b1.jar ./WEB-INF/lib/hibernate/cglib.jar ./WEB-INF/lib/hibernate/dom4j.jar ./WEB-INF/lib/hibernate/freemarker.jar ./WEB-INF/lib/hibernate/hibernate-annotations.jar ./WEB-INF/lib/hibernate/hibernate-shards.jar ./WEB-INF/lib/hibernate/hibernate-tools.jar ./WEB-INF/lib/hibernate/hibernate.jar ./WEB-INF/lib/hibernate/jtidy-r8-20060801.jar ./WEB-INF/lib/jabsorb ./WEB-INF/lib/jabsorb/jabsorb-1.3.1.jar ./WEB-INF/lib/jta.jar ./WEB-INF/lib/jyaml-1.3.jar ./WEB-INF/lib/postgresql-8.4-701.jdbc4.jar ./WEB-INF/lib/sjsxp.jar ./WEB-INF/lib/spring ./WEB-INF/lib/spring/org.springframework.aop-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.asm-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.aspects-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.beans-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.context-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.context.support-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.core-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.expression-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.instrument-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.instrument.tomcat-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.jdbc-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.jms-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.orm-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.oxm-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.test-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.transaction-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web.portlet-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web.servlet-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web.struts-3.0.0.RELEASE.jar ./WEB-INF/lib/testng-5.11-jdk15.jar ./WEB-INF/web.xml

    Read the article

  • Spring Security - Interactive login attempt was unsuccessful

    - by Taylor L
    I've been trying to track down why Spring Security isn't creating the SPRING_SECURITY_REMEMBER_ME_COOKIE so I turned on logging for org.springframework.security.web.authentication.rememberme. At first glance, the logs make it seem like the login is failing but the login is actually successful in the sense that if I navigate to a page that requires authentication I am not redirected back to the login page. However, the logs appear to be saying the login credentials are invalid. Any ideas as to what is going on? Mar 16, 2010 10:05:56 AM org.springframework.security.web.authentication.rememberme.PersistentTokenBasedRememberMeServices onLoginSuccess FINE: Creating new persistent login for user [email protected] Mar 16, 2010 10:10:07 AM org.springframework.security.web.authentication.rememberme.AbstractRememberMeServices loginFail FINE: Interactive login attempt was unsuccessful. Mar 16, 2010 10:10:07 AM org.springframework.security.web.authentication.rememberme.AbstractRememberMeServices cancelCookie FINE: Cancelling cookie <http auto-config="false"> <intercept-url pattern="/css/**" filters="none" /> <intercept-url pattern="/img/**" filters="none" /> <intercept-url pattern="/js/**" filters="none" /> <intercept-url pattern="/app/admin/**" filters="none" /> <intercept-url pattern="/app/login/**" filters="none" /> <intercept-url pattern="/app/register/**" filters="none" /> <intercept-url pattern="/app/error/**" filters="none" /> <intercept-url pattern="/" filters="none" /> <intercept-url pattern="/**" access="ROLE_USER" /> <logout logout-success-url="/" /> <form-login login-page="/app/login" default-target-url="/" authentication-failure-url="/app/login?login_error=1" /> <session-management invalid-session-url="/app/login" /> <remember-me services-ref="rememberMeServices" key="myKey" /> </http> <authentication-manager alias="authenticationManager"> <authentication-provider user-service-ref="userDetailsService"> <password-encoder hash="sha-256" base64="true"> <salt-source user-property="username" /> </password-encoder> </authentication-provider> </authentication-manager> <beans:bean id="userDetailsService" class="com.my.service.auth.UserDetailsServiceImpl" /> <beans:bean id="rememberMeServices" class="org.springframework.security.web.authentication.rememberme.PersistentTokenBasedRememberMeServices"> <beans:property name="userDetailsService" ref="userDetailsService" /> <beans:property name="tokenRepository" ref="persistentTokenRepository" /> <beans:property name="key" value="myKey" /> </beans:bean> <beans:bean id="persistentTokenRepository" class="com.my.service.auth.PersistentTokenRepositoryImpl" />

    Read the article

  • Troubleshooting .NET "Fatal Execution Engine Error"

    - by JYelton
    Summary: I periodically get a .NET Fatal Execution Engine Error on an application which I cannot seem to debug. The dialog that comes up only offers to close the program or send information about the error to Microsoft. I've tried looking at the more detailed information but I don't know how to make use of it. Error: The error is visible in Event Viewer under Applications and is as follows: .NET Runtime version 2.0.50727.3607 - Fatal Execution Engine Error (7A09795E) (80131506) The computer running it is Windows XP Professional SP 3. (Intel Core2Quad Q6600 2.4GHz w/ 2.0 GB of RAM) Other .NET-based projects that lack multi-threaded downloading (see below) seem to run just fine. Application: The application is written in C#/.NET 3.5 using VS2008, and installed via a setup project. The app is multi-threaded and downloads data from multiple web servers using System.Net.HttpWebRequest and its methods. I've determined that the .NET error has something to do with either threading or HttpWebRequest but I haven't been able to get any closer as this particular error seems impossible to debug. I've tried handling errors on many levels, including the following in Program.cs: // handle UI thread exceptions Application.ThreadException += new ThreadExceptionEventHandler(Application_ThreadException); // handle non-UI thread exceptions AppDomain.CurrentDomain.UnhandledException += new UnhandledExceptionEventHandler(CurrentDomain_UnhandledException); Application.EnableVisualStyles(); Application.SetCompatibleTextRenderingDefault(false); // force all windows forms errors to go through our handler Application.SetUnhandledExceptionMode(UnhandledExceptionMode.CatchException); More Notes and What I've Tried... Installed Visual Studio 2008 on the target machine and tried running in debug mode, but the error still occurs, with no hint as to where in source code it occurred. When running the program from its installed version (Release) the error occurs more frequently, usually within minutes of launching the application. When running the program in debug mode inside of VS2008, it can run for hours or days before generating the error. Reinstalled .NET 3.5 and made sure all updates are applied. Broke random cubicle objects in frustration. Rewritten parts of code that deal with threading and downloading in attempts to catch and log exceptions, though logging seemed to aggravate the problem (and never provided any data). Question: What steps can I take to troubleshoot or debug this kind of error? Memory dumps and the like seem to be the next step, but I'm not experienced at interpreting them. Perhaps there's something more I can do in the code to try and catch errors... It would be nice if the "Fatal Execution Engine Error" was more informative, but internet searches have only told me that it's a common error for a lot of .NET-related items.

    Read the article

< Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >