Search Results

Search found 5398 results on 216 pages for 'xorg conf'.

Page 162/216 | < Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• NetBeans Hangs on New Project Creation

  - by Jason

  When creating a New Project in NetBeans, it hangs on the creation screen; Screenshot I'm running Netbeans 7.0.1 on Xubuntu 13.04. Java -version prints: java version "1.7.0_25" OpenJDK Runtime Environment (IcedTea 2.3.10) (7u25-2.3.10-1ubuntu0.13.04.2) OpenJDK 64-Bit Server VM (build 23.7-b01, mixed mode) /usr/lib/jvm/ contains the following folders; java-1.5.0-gcj-4.7-amd64 java-6-openjdk-amd64 java-7-openjdk-common java-1.6.0-openjdk-amd64 java-6-openjdk-common java-1.7.0-openjdk-amd64 java-7-openjdk-amd64 I tried editing /usr/share/netbeans/7.0.1/etc/netbeans.conf with the following (as was suggested in another post); netbeans_jdkhome="/usr/lib/jvm/java-7-openjdk-amd64/jre/" But that didn't work. Instead, NetBeans then presented an error on the loading splash when it reached "Turning on Modules..." claiming the JDK was missing. Both NetBeans and the OpenJDK Java 7/6 Runtimes were installed through the Ubuntu Software Centre. I've also tried uninstalling and reinstalling both Java and NetBeans. Any help would be greatly appreciated, thanks!

  Read the article

• Make the sound louder in Lubuntu

  - by Andrew

  I have a Toshiba r835 running Lubuntu 11.10. Turning the volume slider up all the way doesn't give very loud sound. I've tried typing alsamixer in a terminal and turning up all the levels there to maximum, but the speakers are still fairly quiet. Is there a simple way to increase maximum volume in software? I understand that there are physical limits to the sound the laptop's speakers can produce, but I suspect my maximum volume is limited by software. EDIT: This is exactly the type of solution I'm looking for. However, it doesn't work for me. What I did: sudo pico /etc/asound.conf This file does not exist, so I create a new one, containing: pcm.!default { type plug slave.pcm "softvol" } pcm.softvol { type softvol slave { pcm "dmix" } control { name "Pre-Amp" card 0 } min_dB -5.0 max_dB 20.0 resolution 6 } I reboot the machine, and type alsamixer. I use my left/right arrow keys to inspect the various volume options. I expect to see a new option, called Pre-Amp, but I don't see one. This fix seems to work for other people. Why doesn't this fix work for me?

  Read the article

• LTS 12.04.1 will not resolve domain.local websites

  - by user108502

  I have done a brand new installation of the Ubuntu server (v12.10) with bind configured to have a dns zone of gdos.local and apache configured for said domain. With a brand new installation of Ubuntu desktop LTS I try to connect to www.gdos.local and all I get is: Server not found Firefox can't find the server at www.gdos.local. Check the address for typing errors such as ww.example.com instead of www.example.com However if I change the domain to gdos.tmp and type in www.gdos.tmp, I get the internal website. If I change it to mybusiness.local , I get the same error message. If I use a Microsoft os, this works fine, all three domains resolve to a webpage. I have searched the internet flat for the past week on dns issues but have not come up with a solution. I have followed instructions from removing dnsmasq to editing like resolv.conf (in some very strange places) and I still have no joy on getting the .local domain extension to work. I can safely say the issue is not with the server but with the desktops because if the issue was server related the Microsoft OS's would not resolve it either. I have done several installs of the desktop in an effort to make sure that I did not break anything while trying to fix this. Please can anyone point to a workable solution for fixing the .local domain extension. Thank you Mark Hollander

  Read the article

• What am I doing wrong in my config for MySql?

  - by Knight Hawk3

  When I load my my.conf with the config at the bottom Mysql fails to start and prints no errors. I am running Arch Linux (Updated) with the latest MySQL (5.5) and the latest nginx (Well latest in the repository, Not sure how to check. Only installed it today) I will give you any info you ask for. Thanks for helping! # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/run/mysqld/mysqld.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/run/mysqld/mysqld.sock skip-locking key_buffer = 16K max_allowed_packet = 1M table_cache = 4 sort_buffer_size = 64K read_buffer_size = 256K read_rnd_buffer_size = 256K net_buffer_length = 2K thread_stack = 64K # Don’t listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (using the “enable-named-pipe” option) will render mysqld useless! # #skip-networking server-id = 1 # Uncomment the following if you want to log updates #log-bin=mysql-bin # Uncomment the following if you are NOT using BDB tables skip-bdb # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = /var/lib/mysql/ #innodb_data_file_path = ibdata1:10M:autoextend #innodb_log_group_home_dir = /var/lib/mysql/ #innodb_log_arch_dir = /var/lib/mysql/ # You can set .._buffer_pool_size up to 50 – 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 16M #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 5M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 skip-innodb [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 1M sort_buffer_size = 1M [myisamchk] key_buffer = 1M sort_buffer_size = 1M [mysqlhotcopy] interactive-timeout So what is my silly error?

  Read the article

• Can't complete dropbox installation from behind proxy in Ubuntu 11.10

  - by Mark Jones

  Problem: My PC on campus sits behind a proxy (requiring authentication) and I can't setup Dropbox. I am convinced that this is a proxy issue as I can't setup Ubuntu one either (but I don't use Ubuntu One so that is not a problem). I have looked at the Ubuntu One fix but it seems to be to modify settings explicitly related to Ubuntu One. I can install the nautilus-dropbox package (compiled from source and from .deb package from website and from software centre) but once I click OK from the "Dropbox Installation" dialog box (prompting me to download the proprietary daemon) the installation just freezes with the OK button pressed. When I look at its process in System Monitor its waiting channel is inet_wait_for_connect. I have set the following proxy directives thus far: Added mj22:**@proxy.waikato.ac.nz:80 information to network proxy settings under network in settings. Added http_host and http_port variables under gconf-editor-system-proxy Added 'host', 'authentication_password' 'authentication_user' and ticked 'user authentication' and 'use_http_proxy' under gconf-editor-system-http_proxy Added export http_proxy="http://mj22:**@proxy.waikato.ac.nz:80/" to /etc/bash.bashrc Added Acquire::http::proxy "http://mj22:**@proxy.waikato.ac.nz:80/"; to /etc/apt/apt.conf (which is what I imagine is letting Software Center retrieve packages). (where ** is my password) I have also added the equivalent ftp and https lines for the above entries. I get the internet fine and Software Centre can download packages but thats it. Related issues: The software centre can't fetch reviews (but can download packages). When trying to add an online account in Gnome 3 a dialog pop up appears with "Error getting a Request Token: Cannot connect to proxy (proxy.waikato.ac.nz)" Updates: After some time (10mins ish) Dropbox shows an error dialog box that reads: Trouble connecting to Dropbox servers. Maybe your internet connection is down, or you need to set you http_proxy environment variable. Is there a way I can see what environment variables are currently set?

  Read the article

• apt-get upgrade stuck at the same package

  - by decibyte

  Current status I've started to suspect this is not an Ubuntu issue, but related to the internet connection here at my work. Until I'm sure, Im leaving my question below: Original question I'm stuck, can't upgrade my system. Running sudo apt-get upgrade gives me the following: mmm@alalunga:~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: ginn libgrip0 linux-generic-pae linux-headers-generic-pae linux-image-generic-pae The following packages will be upgraded: apport apport-gtk bind9-host build-essential dhcp3-client dhcp3-common dnsutils eog evince evince-common firefox firefox-branding firefox-dbg firefox-globalmenu firefox-gnome-support firefox-locale-en gimp gimp-data gir1.2-totem-1.0 glib-networking glib-networking-common glib-networking-services gnupg gpgv icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-6-plugin icedtea-netx icedtea-netx-common icedtea-plugin isc-dhcp-client isc-dhcp-common libapache2-mod-php5 libart-2.0-2 libbind9-80 libdns81 libevince3-3 libgimp2.0 libisc83 libisccc80 libisccfg82 liblwres80 libssl-dev libssl-doc libssl1.0.0 libtotem0 linux-firmware linux-libc-dev openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssl php-pear php5-cli php5-common php5-curl php5-dev php5-gd php5-mysql php5-xsl policykit-1-gnome python-apport python-django python-gst0.10 python-problem-report resolvconf thunderbird thunderbird-globalmenu thunderbird-gnome-support totem totem-common totem-mozilla totem-plugins xserver-xorg-input-synaptics 74 upgraded, 0 newly installed, 0 to remove and 5 not upgraded. Need to get 317 MB/327 MB of archives. After this operation, 1.481 kB of additional disk space will be used. Do you want to continue [Y/n]? Get:1 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:2 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:3 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:4 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:5 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:6 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:7 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] 9% [7 openjdk-6-jre-headless 27,3 MB/27,3 MB 100%] It keeps downloading the package openjdk-6-jre-headless, then does nothing for a while (hanging on what's the last line above), then download the package again. It's at its 13th download attempt at the moment of writing. The actual downloads seem to be done just fine, but whatever it does after downloading seems to be failing. I tried removing openjdk-6, but then it wanted to install openjdk-7 instead, with the same result, hanging at openjdk-7-jre-headless instead. I also tried changing servers from my local (Danish) to the main server. No luck. It's also keeping me from upgrading alle the other packages. What to do? Update After following instructions in the answer by @lpanebr, it is now stuck at the linux-firmware package. So, maybe it's a more general problem than being related to specific package(s)? Although it did download some packages without problems before getting stuck at linux-firmware.

  Read the article

• bluetooth daemon not running at startup

  - by ffaxer

  I'm trying to connect a bluetooth mouse to my Xubuntu system using Blueman (v. 1.21) Problem seems to be bluetoothd not running at startup, so blueman refuses to start, only a dialog appears: "Bluez daemon is not running, blueman-manager cannot continue." On my system, bluetoothd will run only as root (sudo), so my current workaround is simply to sudo bluetoothd manually, which works fine but id like to have it run at startup so that my mouse is just working without any interaction from me, if possible. If i try to start bluetoothd as non-root it reports: Bluetooth deamon 4.91 Unable to get on D-Bus In the startup scripts i found the same bluetoothd script in all runlevels and init.d: DAEMON=/usr/sbin/bluetoothd test -f /usr/sbin/bluetoothd || exit 0 # bluetoothd normally starts up by udev rules. it needs dbus to function, log_progress_msg "bluetoothd" pkill -TERM bluetoothd || true log_progress_msg "bluetoothd" I looked in /etc/udev/rules.d/ but no reference to bluetoothd. Further i have already tried with no luck: Editing /etc/dbus-1/system.d/bluetooth.conf to include my user (essentially copying the part that was for root): I tried it while both keeping the root policy and without, still, no luck! Editing /etc/pam.d/common-session and /etc/pam.d/gdm to include the line: session optional pam_ck_connector.so In the case of common-session it was already there but with a "nox11" which i tried removing. No luck no luck. Btw, I'm confused as to which session manager I'm using, since i have both xfce4-session and gdm-session-worker running. Anyways, hope someone is savvy enough to figure it out or bring some hints, otherwise i sincerely apologize for wasting your time! I'll sign off with uname -a: Linux [mycompname] 3.0.0-9-lowlatency #12ppa1~natty1-Ubuntu SMP PREEMPT Mon Aug 22 06:52:15 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux Peace B)

  Read the article

• Cannot ping any computers on LAN

  - by Timothy

  I havem't been able to find a straight forward answer on this yet. I'm hoping people here are able to help! Keep in mind that I'm a complete beginner at this - this is the first installation i've done for any LINUX systems ever so please keep that in mind when answering this question. We are a complete Windows shop, using nothing but Microsoft products but looking into the value of OpenStalk however have been having problems getting Ubuntu Server installed and speaking to the network. The machine is getting an IP address which is telling me that some sort of DHCP activity is working but I'm not able to ping any computer on our network as well as not able to connect to the internet. Every time I try to ping i'm getting; Destination Host Unreachable I've tried using modifying the resolv.conf file with our static details to match my Windows 7 machine still with no luck. Even tried disabling the firewall on Ubuntu Server 11 and no luck. Any ideas? Please let me know if there is any information you need from the server and I'll post up.

  Read the article

• 11.10 desktop alerts (volume change and terminal bell) stopped working but all other audio still works

  - by FlabbergastedPickle

  All, My sound works just fine in 11.10 64-bit install on HP dm1-4050 Sandy Bridge notebook (e.g. audio works in Banshee, flash, games, browser, Thunderbird email notification, etc.), but the core desktop notifications (e.g. pressing a tab in a terminal where there is more than one option should trigger a terminal bell, or changing volume using volume keys should be accompanied with the supporting "quack" that the volume app makes) do not work. I've intentionally disabled login sound as explained here on ask ubuntu but even enabling it back makes no difference. These notifications did work before just fine and I am not sure when did the actually stop working but it must've been fairly recently. Only things I did were trying to install some ppa edge xorg drivers for my intel card (a separate issue) but also reverted them all with ppa-purge once I discovered they did not improve anything. Other thing I did was check volume settings with alsamixer and did alsactl store for the soundcard after I did some experimenting with volume settings for PCM (on my laptop PCM at 100% crackles so I had to lower it and make pulseaudio ignore its setting as per ask ubuntu's page). That said, neither of these should have any bearing on the said notifications since the volume is up and they clearly work everywhere else but the core desktop events. The system ready drum sound when Ubuntu boots and user reaches the login screen also does not work. The guest login behaves exactly same as mine. Audio works (including the login sound since I've not disabled it for the guest account), but no quacks when changing the volume or terminal bell sounds... I've tried copying ubuntu sounds to /usr/share/sounds/ as suggested on ask ubuntu and that did not work. I also tried using dconf-editor to check sound theme settings and tried both freedesktop (which is what it was set to) and ubuntu, as suggested on ask ubuntu. This did not work either. I tried purging the ~/.pulse folder and the /tmp/*pulse* entries, rebooting and restarting pulseaudio with -D flag. While audio came back on and behaved just fine in all aspects (e.g. one can adjust volume levels, play music, games, in-browser sound stuff, and other app alerts) except for the system ready drum sound (at the login screen), and any system event (terminal bell and volume change quack sound). It is interesting that the quack sound works inside system settings-sound when adjusting levels there, but it does not when volume is changed via top bar's volume settings... I do recall that at one point yesterday when I was restarting pulseaudio the quacks that accompany volume change did start working but I have no idea what caused that. This was also when I first realized those alerts were not working. After rebooting it was again gone. I did compile my own 3.0.14-rt31 kernel a little while ago as instructed on one of the wiki's for the 11.10 rt kernel. Everything works as before except for the said sound alerts. I am not sure if this began happening since I started using the rt kernel though and yesterday's momentary ability to hear those quacks while changing the volume make me believe that the kernel is not one responsible for this problem. One more thing I can think of is that I used alsoft-conf tool to configure buffering on the OpenAL (due to TA Spring's choppy audio) and changed in there default audio device to ALSA. I also tried reverting it to Pulseaudio as the only allowed output but the bottom part of the Backend tab always reverts to ALSA even when I select Pulseaudio. The pulseaudio does remain as the only active choice on top. This, however, once again does not make any sense in terms of preventing desktop audio alerts when everything else including OpenAL games plays sound just fine... So, there you have it, as verbose as I could make it :-). I tried all I could find on this issue and had no luck so far... Any ideas?

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• How to update Adobe's software unattendedly?

  - by jubel

  I would like to use unattended-upgrade to update the Adobe Reader, Flash Player and everything else of the Canonical partners. There fore, I added in /etc/apt/apt.conf.d/50unattended-upgrades Unattended-Upgrade::Allowed-Origins { "${distro_id} ${distro_codename}-security"; "${distro_id} ${distro_codename}-updates"; "Canonical ${distro_codename}"; // "${distro_id} ${distro_codename}-proposed"; // "${distro_id} ${distro_codename}-backports"; }; sudo unattended-upgrade --dry-run -d says Initial blacklisted packages: Starting unattended upgrades script Allowed origins are: ['o=Ubuntu,a=oneiric-security', 'o=Ubuntu,a=oneiric-updates', 'o=Canonical,a=oneiric'] Checking: acroread-common (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobe-flash-properties-gtk (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobe-flashplugin (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobereader-deu (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: handbrake-cli (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-stebbins-handbrake-snapshots' label:'HandBrake Snapshots' site:'ppa.launchpad.net' isTrusted:True>"]) Checking: handbrake-gtk (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-stebbins-handbrake-snapshots' label:'HandBrake Snapshots' site:'ppa.launchpad.net' isTrusted:True>"]) Checking: sopcast-player (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-ferramroberto-sopcast' label:'LffL Sopcast' site:'ppa.launchpad.net' isTrusted:True>"]) pkgs that look like they should be upgraded: Fetched 0 B in 0s (0 B/s) blacklist: [] InstCount=0 DelCount=0 BrokenCout=0 No packages found that can be upgraded unattended And it won't update. How can I update the third-party software automatically?

  Read the article

• Problem connecting to isp server using xl2tpd as client. Ubuntu server 13.04

  - by Deon Pretorius

  I have followed guides found on google and ubuntu support pages and can get xl2tpd connection up but only under the following conditions: 1 - ADSL model must be configured and connected to the ISP or 2 - ADSL modem in bridge mode I must have an existing PPPoe connection established. If neither of the above are active xl2tpd wont trigger pppd and connect to the isp and thus tunnel connection fails to connect to the L2TP server of the ISP. Am I doing something wrong; /etc/ppp/options.l2tpd.axxess ipcp-accept-local ipcp-accept-remote refuse-eap refuse-chap require-pap noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute usepeerdns debug lock connect-delay 5000 name (name used for ppp connection) /etc/ppp/pap-secrets # * password (name used for ppp connection as above) * (ppp password supplied by isp) /etc/xl2tpd/xl2tpd.conf [global] ; Global parameters: auth file = /etc/xl2tpd/l2tp-secrets ; * Where our challenge secrets are access control = yes ; * Refuse connections without IP match debug tunnel = yes [lac axxess] lns = 196.30.121.50 ; * Who is our LNS? redial = yes ; * Redial if disconnected? redial timeout = 5 ; * Wait n seconds between redials max redials = 5 ; * Give up after n consecutive failures hidden bit = yes ; * User hidden AVP's? length bit = yes ; * Use length bit in payload? require pap = yes ; * Require PAP auth. by peer require chap = no ; * Require CHAP auth. by peer refuse chap = yes ; * Refuse CHAP authentication require authentication = yes ; * Require peer to authenticate name = BLA85003@axxess ; * Report this as our hostname ppp debug = yes ; * Turn on PPP debugging pppoptfile = /etc/ppp/options.l2tpd.axxess ; * ppp options file for this lac /etc/xl2tpd/l2tp-secrets # Secrets for authenticating l2tp tunnels # us them secret # * marko blah2 # zeus marko blah # * * interop * vzb_l2tp (*** secret supplied by isp) ^ isp server host name Any help will be greatly appreciated

  Read the article

• Unable to access any ubuntu shares from android/windows clients

  - by dan

  I am running Ubuntu 11.04, and cant seem to access any of my shares. Here is the output from testparm-s : Load smb config files from /etc/samba/smb.conf rlimit_max: increasing rlimit_max (1024) to minimum Windows limit (16384) Processing section "[printers]" Processing section "[CanonMG2100AIO]" Processing section "[FreeAgent Drive]" Loaded services file OK. WARNING: You have some share names that are longer than 12 characters. These may not be accessible to some older clients. (Eg. Windows9x, WindowsMe, and smbclient prior to Samba 3.0.) Server role: ROLE_STANDALONE [global] server string = %h server (Samba, Ubuntu) encrypt passwords = No obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = Enter\snew\s\spassword:* %n\n Retype\snew\s\spassword:* %n\n password\supdated\ssuccessfully . username map = /etc/samba/smbusers unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 name resolve order = wins lmhosts host bcast dns proxy = No wins support = Yes usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d [printers] comment = All Printers path = /var/spool/samba create mask = 0700 guest ok = Yes printable = Yes browseable = No [CanonMG2100AIO] comment = Printer Drivers path = /var/lib/samba/printers read only = No guest ok = Yes [FreeAgent Drive] path = /media/FreeAgent Drive read only = No guest ok = Yes smbtree: Server requested plaintext password but 'client plaintext auth' is disabled anonymous failed session setup with NT_STATUS_INVALID_PARAMETER Server requested plaintext password but 'client plaintext auth' is disabled anonymous failed session setup with NT_STATUS_INVALID_PARAMETER and hostname: dekstop I know the spelling of desktop is incorrect. it was a duh moment. Any help would be greatly appreciated.

  Read the article

• Why is Ubuntu offline (except torrents) while Windows is online?

  - by Fahim al Islam

  I am using a static wired connection. Everything was perfect. But suddenly from few hours back I can't access any website. Dropbox, Ubuntu One also can't connect. Ping request is also unsuccessful, but I can download through torrent. I am not trying torrent download and browsing at the same time. So, I think it's not an issue about torrent using all the bandwidth. One important point is that this connection works perfectly on Windows on this same PC (My PC is dual-boot). I have tried the way what izx has suggested (using "sudo sh -c 'echo nameserver 8.8.8.8 /etc/resolv.conf'"), but I'm facing the same problem again. Now I can't even ping 8.8.8.8 and google.com. Though I can ping 74.125.228.2 (which is Google IP address) I can't understand what's happening and why this is happening. I'm new in this website many rules and regulations is unknown to me. So, please don't be bothered for my mistakes. Looking forward for help from anyone. Thanks to all.

  Read the article

• XSF-FO intellisense and national languages with Apache FOP

  - by Lukasz Kurylo

  Some time ago I showed how to get an intellisense and how to configure the FO.NET to acquire national characters inside the generated pdf files. Due to the limitations that I mensioned in my previous post, I started playing with the Apache FOP. In this post I want to show, how to acquire the same result as I showed in the two posts related to FO.NET.   Intellisense   To get the intellisense from the XSL-FO templates set the xsi:schemaLocation the same way I showed it in this post. The only diffrence to FO.NET is that, during generating the document by the code I showed last time we will get an exception:   org.apache.fop.fo.ValidationException: Invalid property encountered on "fo:root": xsi:schemaLocation (See position 6:11)   Fortunatelly there is a very easy way to resolve this without removing the entire attribute along with the intellisense. Add to the FopFactory the ignoreNamespace by:   FopFactory fopFactory = FopFactory.newInstance(); fopFactory.ignoreNamespace(http://www.w3.org/2001/XMLSchema-instance);   Notice that, the url specified in this method this is a namespace for the xmlns:xsi namespace, not xsi.schemaLocation.   Fonts / national characters   This point is a little dfferent to acquire, but not more complicated that it was with FO.NET. To set the fonts in Apache FOP 1.0, we need a configuration file. A sample one can be get from the directory where we unpacked the fop binaries, from conf subdirectory. There is a file called fop.xconf. We must copy this file to our solution. In the simplest way, in the <fonts> tag we can add  <auto-detect/>. Thanks to this, FOP will index all fonts available on the installed operating system. There probably should be no problem, if we have a http handler or a WCF Service on the server that serves the generated pdf documents. In this situation we can use all available fonts on this server.   To use this config file, we must set a path to it:   FopFactory fopFactory = FopFactory.newInstance(); fopFactory.setUserConfig(new File("fop.xconf"));

  Read the article

• Killing a Plesk 11.5 backup process in Ubuntu

  - by Klaaz

  I want to kill a backup process initiated by Plesk in Ubuntu but don't know which processes safely can be killed: ps aux | grep backup root 20505 0.0 0.0 4392 604 ? Ss 01:43 0:00 /bin/sh -c [ -x /opt/psa/admin/sbin/backupmng ] && /opt/psa/admin/sbin/backupmng >/dev/null 2>&1 psaadm 20510 0.0 0.0 30884 1816 ? S 01:43 0:00 /opt/psa/admin/sbin/backupmng psaadm 20511 0.0 0.0 30884 644 ? S 01:43 0:01 /opt/psa/admin/sbin/backupmng psaadm 20512 0.0 0.6 270472 49356 ? S 01:43 0:03 /usr/bin/sw-engine -c /opt/psa/admin/conf/php.ini /opt/psa/admin/plib/backup/scheduled_backup.php --dump 1 root 20517 0.0 14.9 1400124 1214696 ? SN 01:43 0:27 /usr/bin/perl /opt/psa/admin/bin/plesk_agent_manager server --owner-uid=0bd9576c-f832-4362-b4f4-3c1afac22be2 --owner-type=server --dump-rotation=7 --backup-profile-name=serverXL_ --session-path=/opt/psa/PMM/sessions/2013-10-23-014303.864 --output-file=ftp://[email protected]//backup/serverXL/ --ftp-passive-mode root 27423 0.0 0.0 13652 888 pts/2 S+ 10:35 0:00 grep --color=auto backup root 29103 1.0 14.8 1400124 1209760 ? SN 02:16 5:21 /usr/bin/perl /opt/psa/admin/bin/plesk_agent_manager server --owner-uid=0bd9576c-f832-4362-b4f4-3c1afac22be2 --owner-type=server --dump-rotation=7 --backup-profile-name=serverXL_ --session-path=/opt/psa/PMM/sessions/2013-10-23-014303.864 --output-file=ftp://[email protected]//backup/serverXL/ --ftp-passive-mode root 29106 0.0 14.8 1400404 1212456 ? DN 02:16 0:07 /usr/bin/perl /opt/psa/admin/bin/plesk_agent_manager server --owner-uid=0bd9576c-f832-4362-b4f4-3c1afac22be2 --owner-type=server --dump-rotation=7 --backup-profile-name=serverXL_ --session-path=/opt/psa/PMM/sessions/2013-10-23-014303.864 --output-file=ftp://[email protected]//backup/serverXL/ --ftp-passive-mode It seems the FTP process is the culprit?

  Read the article

• After login I only get a terminal window

  - by Ambidex

  First of, let me tell you I'm a n00b at ubuntu. I have updated my Ubuntu mediacenter to a later version of ubuntu, currently at 12.04. I'm working through a lot of updates to get to the latest. But since my first update I got the new login screen (lightdm?) and my autologin wasen't working anymore. So I Googled how I could make lightdm autologin. I've managed this by making my /etc/lightdm/lightdm.conf look as follows: [SeatDefaults] greeter-session=unity-greeter user-session=ubuntu autologin-user=my_user autologin-userutologin-user=-timeout=0 Which seemed to work... But now that it automatically logs in, I seem to get the following type of screen (through nomachine remote desktop client): Sorry... I am unable to post my screenshot here because I do not have the 10 reputation points in askubuntu yet.... darn it... But the screen has a terminal at the top left of the screen (not an actual "window"), and the ubuntu loading screen is still behind it. I've tried running startx as you can see. But, this seems to actually be x server. But if I run unity --reset, it seems that a lot of the desktop gets restored, but... with a lot of errors and warnings and the next time I boot, it's the same story all over again. Also, when I close the terminal window after getting my desktop back, I get thrown back at the login screen. Please bear with my lack of knowledge of ubuntu and it's underlying unix. I thank you in advance.

  Read the article

• Recovering data from /

  - by Abhijit Gavas

  I accidentally installed Ubuntu to one of my data drives from Windows. The drive was a NTFS drive and contained about 80 GB of important data. The size of the drive is 110 GB. Its new file system is ext4. In an attempt to recover the data, I downloaded foremost and tried the following commands: foremost -i / -o /media/281C8DB01C8D7998/Recovery/ -T -v foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v (sda7 is the drive in question.) It appears that with either command, foremost gets stuck reading some file. Here is the console output: abhi@abi-PC:/dev$ foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Foremost version 1.5.7 by Jesse Kornblum, Kris Kendall, and Nick Mikus Audit File Foremost started at Fri Sep 28 20:58:00 2012 Invocation: foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Output directory: /media/281C8DB01C8D7998/Recovery_Fri_Sep_28_20_58_00_2012 Configuration file: /etc/foremost.conf Processing: stdin |------------------------------------------------------------------ File: stdin Start: Fri Sep 28 20:58:00 2012 Length: Unknown Num Name (bs=512) Size File Offset Comment Killed As you can see I have to kill it from system monitor. This approach does not seem to be working. What else could I try to recover the files? Please help. The files are very important and I will be devastated if I cannot recover them.

  Read the article

• Problems with wired ethernet connection Ubuntu 11.10

  - by Andrew Fielden

  After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

  Read the article

• Is a disk/ata timeout exception dangerous?

  - by j-g-faustus

  I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

  Read the article

• Connecting to wireless networks from command line

  - by Balaji

  I need to write a shell script which connects to one of the two available wi-fi connections. One is a un secure connection and the other is secure connection. My question has 2 parts- 1.How to connect to the un-secure (un-encrypted and no password required) connection from command line (or by executing a shell script) when I'm connected to the secure connection? I followed the steps in http://www.ubuntugeek.com/how-to-troubleshoot-wireless-network-connection-in-ubuntu.html for in-secure connection. I put all the commands in a script and executed it (I made sure that interface name and essid are correct) - sudo dhclient -r wlan0 - sudo ifconfig wlan0 up - sudo iwconfig wlan0 essid "UAPublic" - sudo iwconfig wlan0 mode Managed - sudo dhclient wlan0 But nothing happens - I'm not disconnected from the current network and connected to the new one 2.When I want to connect to the secure wi-fi network, I understand from http://askubuntu.com/a/138476/70665 that I need to use wpa_supplicant. But I enter a lot of details in the interface when I connect via UI security : wpa and wpa2 enterprise Authentication : PEAP CA certificate : Equifax... PEAP version : automatic inner authentication : MSCHAPv2 username : password : How to use wpa_supplicant to mention all these details in the command line? The conf file network={ ssid="ssid_name" psk="password" } doesn't work for me.

  Read the article

• Static IP Address on Ubuntu 12.04 Virtual Machine

  - by chrisnankervis

  I've setup a VM running Ubuntu 12.04 specifically for local web development and am having some problems ensuring it has a static IP address. A static IP address is important as I'm using the IP address in my hosts file to assign a .local suffix to addresses used both in browser and to connect to the correct database on the VM. Currently, every time I connect to a new network or my VM is assigned a new IP address I need to reconfigure my whole environment which is becoming quite a pain. It also probably doesn't help that the default-lease-time on the Ubuntu VM is set to 1800 by default. At the moment I'm using VMWare Fusion and the Network Adapter is enabled and set to "Autodetect" under Bridged Networking. I've tried to set a static IP address within the dhcpd.conf using the code below: host ubuntu { hardware ethernet 00:50:56:35:0f:f1; fixed-address: 192.168.100.100; } The fixed-address that I've used is also outside the range specified in the subnet block (which in this case is 192.168.100.128 to 192.168.100.254). I've tried adding and removing the network adapter and restarting my Mac after each time to no avail. Below is an ifconfig of the VM that might be of some help: eth0 Link encap:Ethernet HWaddr 00:50:56:35:0f:f1 inet addr:192.168.0.25 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe35:ff1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1624 errors:0 dropped:0 overruns:0 frame:0 TX packets:416 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:147348 (147.3 KB) TX bytes:41756 (41.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Are there any specific issues with 12.04 that I'm missing? Otherwise has anyone else got any ideas? Thanks in advance.

  Read the article

• Unable To Get Sound Working to External Speaker on HP TouchSmart 320 on 11.04 or 11.10

  - by Schof

  This is an HP TouchSmart 320, model number 320-1200m. I'm using Ubuntu 11.04. Hardware information: root@hp320:/home/mpower# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Generic [HD-Audio Generic], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 root@hp320:~$ cat /proc/asound/card0/codec#0 | grep Codec Codec: IDT 92HD91BXX Sound to headphone jack works properly, but sound to built-in speakers does not work. I have installed Windows, and with Windows 7 installed, all audio hardware works properly, so this isn't a hardware fault. I've looked at https://help.ubuntu.com/community/HdaIntelSoundHowto and have been unable to find my card in http://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio-Models.txt . I have tried adding almost every conceivable model in the line "options snd-hda-intel model=MODEL" line I added to /etc/modprobe.d/alsa-base.conf. Update 2011-11-09 2:31 PM PST: I've gone to Control Center - Sound Preferences to attempt settings that make sound work. The "Hardware" tab shows one device: "Internal Audio 1 Output / 1 Input Analog Stereo Duplex." There are two output profiles listed in the selection box at the bottom of the tag: Analog Stereo Duplex and Analog Stereo Output. Neither cause sound to emit from the speakers. I've also run alsamixer on the command-line and ensured that everything is set to maximum and nothing is muted. Update 2011-11-09 5:15 PM PST: I've replicated the exact same symptoms in 11.10. Update 2011-11-10 11:31 AM PST: I've filed a bug in launchpad: https://launchpad.net/ubuntu/+source/alsa-driver/+bug/888703

  Read the article

• Configuring Samba to allow Use of CUPS printer

  - by Skizz

  Having trouble with samba printing. I have a CUPS printer installed on an Ubuntu 11.04 server and that works great. When I try to configure samba to allow an XP machine to use the printer, it fails when printing. I can install the printer drivers for XP from the server and the printer appears in the XP printer control panels. When I try to print a test page from the XP machine I get this error in the system event log: Jun 27 20:33:29 FatController smbd[3571]: [2012/06/27 20:33:29, 0] rpc_server/srv_netlog_nt.c:603(_netr_ServerAuthenticate3) Jun 27 20:33:29 FatController smbd[3571]: _netr_ServerAuthenticate3: netlogon_creds_server_check failed. Rejecting auth request from client JAMES machine account JAMES$ Here's my smb.conf file: [global] server string = %h (Server) workgroup = SODOR encrypt passwords = true security = user os level = 255 preferred master = yes domain master = yes local master = yes logon path = \\%L\profile\%U logon drive = S: logon home = \\%L\home\%U domain logons = yes map to guest = Never guest ok = no dns proxy = no time server = yes logon script = logon.bat load printers = yes printing = cups printcap name = cups nt acl support = no interfaces = eth1 lo bind interfaces only = yes smb ports = 445 [netlogon] comment = Net Log On path = /home/samba/netlogon guest ok = no read only = yes browseable = no [profile] comment = User Profiles path = /home/samba/profiles read only = no create mask = 0600 directory mask = 0700 browseable = no store dos attributes = yes [printers] comment = All Printers path = /var/spool/samba browseable = yes guest ok = no printable = yes [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes guest ok = no read only = yes write list = root, skizz Anyone know what the problem is and how to fix it? In addition to the above, I also get this error: Jun 27 21:56:35 FatController smbd[3571]: [2012/06/27 21:56:35, 0] printing/print_cups.c:1027(cups_job_submit) Jun 27 21:56:35 FatController smbd[3571]: Unable to print file to `Edward' - client-error-not-authorized which I think is more relevant.

  Read the article

< Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >