Search Results

Search found 5295 results on 212 pages for 'transaction scope'.

Page 163/212 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• Is this way of using Excel 2007 Pivot table for BI scalable ?

  - by Sim

  Hi all, Background: We need to consolidate sales data across the country to do analysis Our Internet connection/IT expertise/IT investment is not quite strong, therefore full BI solution is out of question I tried several SaaS BI solution (GoodData, ZohoReports) and while they're good, they seem not to fully support what we need We're looking at 'bout 2 millions record for every 2 months My current approach Our (10) sites currently gathers data from all their branches and consolidate them into 1 Excel file with Pivot table and embed source data In HQ, I will request 10 sites to send back those Excel files periodically We will import those Excel to our MSSQL server There will be a master Excel file, that will also have the same pivot table (as those came from site Excel file), and datasource is the MSSQL server More details For testing, I currently use MSSQL 2008 Express on my laptop So far, I imported our transactions for the past 2 months and there are 2 millions+ row in 1 table in MSSQL (we just use 1 table, corresponding to our common pivot table structure). DB size is ~ 600 MB In the master Excel file, if not including the source data, it's just < 10MB. Including the source data will increase the size to 60 MB (so I supposed Office 2007 automatically zip the data ?) I try using the Pivot (drag-and-drop fields) and the performance so far is OK (my laptop specs: C2D T7200, 3GB RAM, Windows XP) So my question is : If we're looking at full year transaction (roughly 15 millions rows in MSSQL 2008 Express, 3.6 GB in size), is there any issue with that 15 million rows in 1 table in SQL Express ? Is there any performance issue with the pivot table at that time ? Can it still embed the source data ? (I google-ed but didn't find the maximum size of source data Excel 2007 can embed) Any other suggestions on how we can better do this ? Given that we can't afford the full BI solution, any light-weight/budget/SaaS BI that you can recommend ? Thanks

  Read the article

• ASP.NET Session State SQL Server 2008 R2 Freezes with High CPU Usage

  - by jtseng

  Our ASP.Net website uses SQL Server as the session state provider. We currently host the database on SQL Server 2005 since it does not play well on 2008 R2. We would like to know why, and how to fix it. hardware setup Our current session state server has SQL Server 2005 with the files hosted on a single local disk. It is one of our oldest servers since it has served us well, and we never felt the need to upgrade it. The database is about 2 GB holding 6000 sessions. (The sessions are a little big, but we need it.) We have another server with SQL Server 2008 R2 with a much faster CPU, much more RAM, and a much faster hard disk. situation One day, we have a huge surge in traffic. The transaction log growth on SQL Server freezes the server for 10's of seconds, allowing only a few requests through in minutes. So we load up the new server with ASPState with very large data and log files and point all of our applications to the new server. It chugs along fine for about 5 minutes, and then the CPU usage jumps up to 50% of the 16 cores that Standard Edition can use and freezes for 10's of seconds at a time. The files do not record any autogrowth events. The disk queue is nice and low. RAM usage is low. CPU usage on our old server has never been higher than 5%. What happened on the new server? Alternatively, I would like to hear success stories with ASP.NET session state server running on SQL Server 2008 R2 with an average write load of 30MB/sec with bursts up to 200MB/sec.

  Read the article

• centos 6.3 kvm external ip forwarding to guests

  - by user1111702

  I have a centos 6.3 server with kvm installed. The server has 4 external ips and one NIC. 176.9.xxx.xx1 176.9.xxx.xx2 176.9.xxx.xx3 176.9.xxx.xx4 I use the following configuration ifcfg-eth0 as slave to ifcfg-br0 the configuration in ifcfg-eth0 is DEVICE=eth0 ONBOOT=yes BRIDGE=br0 HWADDR=14:da:e9:b3:8b:99 and in the ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static BROADCAST=176.9.xxx.xxx IPADDR=176.9.xxx.xx1 NETMASK=255.255.255.0 SCOPE="peer 176.9.xxx.xxx" and I have 3 more aliases for br0 , br0:1 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx2 NETMASK=255.255.255.248 ONBOOT=yes br0:2 to get the trafic from the third external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx3 NETMASK=255.255.255.248 ONBOOT=yes br0:3 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx4 NETMASK=255.255.255.248 ONBOOT=yes The above settings work fine and I recieve the trafic from all the external ips. My problem is that I want to pass the trafic from external ip to specific virtual guest on my server. ie trafic that comes from 176.9.xxx.xxx2 must pass to virtual machine 1 176.9.xxx.xxx3 must pass to virtual machine 2 176.9.xxx.xxx4 must pass to virtual machine 3 Can you please help me how to achieve this ? What are the settings on the host and what should I do to the guests. Thank you in advance

  Read the article

• How to export SQL Server data from corrupted database (with disk write error)

  - by damitamit

  IT realised there was a disk write error on our production SQL Server 2005 and hence was causing the backups to fail. By the time they had realised this the nightly backup was old, so were not able to just restore the backup on another server. The database is still running and being used constantly. However DBCC CheckDB fails. Also the SQL Server backup task fails, Copy Database fails, Export Data Wizard fails. However it seems all the data can be read from the tables (i.e using bcp etc) Another observation I have made is that the Transaction Log is nearly double the size of the Database. (Does that mean all the changes arent being written to the MDF?) What would be the best plan of attack to get the database to a state where backups are working and the data is safe? Take the database offline and use the MDF/LDF to somehow create the database on another sql server? Export the data from the database using bcp. Create the database (use the Generate Scripts function on the corrupt db to create the schema on the new db) on another sql server and use bcp again to import the data. Some other option that is the right course of action in this situation? The IT manager says the data is safe as if the server fails, the data can be restored from the mdf/ldf. I'm not sure so insisted that we start exporting the data each night as a failsafe (using bcp for example). IT are also having issues on the hardware side of things as supposedly the disk error in on a virtualized disk and can't be rebuilt like a normal raid array (or something like that). Please excuse my use of incorrect terminology and incorrect assumptions on how Sql Server operates. I'm the application developer and have been called to help (as it seems IT know less about SQL Server than I do). Many Thanks, Amit

  Read the article

• rsnapshot - not correctly archiving mysql databases

  - by Tiffany Walker

  My rsnapshot configuration: snapshot_root /.snapshots/ backup /home/user localhost/ backup_script /usr/local/backup_mysql.sh localhost/mysql/ Using this file: NOW=$(date +"%m-%d-%Y") # mm-dd-yyyy format FILE="" # used in a loop ### Server Setup ### #* MySQL login user name *# MUSER="root" #* MySQL login PASSWORD name *# MPASS="YOUR-PASSWORD" #* MySQL login HOST name *# MHOST="127.0.0.1" #* MySQL binaries *# MYSQL="$(which mysql)" MYSQLDUMP="$(which mysqldump)" GZIP="$(which gzip)" # get all database listing DBS="$($MYSQL -u $MUSER -h $MHOST -p$MPASS -Bse 'show databases')" # start to dump database one by one for db in $DBS do FILE=$BAK/mysql-$db.$NOW-$(date +"%T").gz # gzip compression for each backup file $MYSQLDUMP --single-transaction -u $MUSER -h $MHOST -p$MPASS $db | $GZIP -9 > $FILE done It dumps the databases under / I then tried with the following: http://bash.cyberciti.biz/backup/rsnapshot-remote-mysql-backup-shell-script/ I got: rsnapshot hourly ---------------------------------------------------------------------------- rsnapshot encountered an error! The program was invoked with these options: /usr/bin/rsnapshot hourly ---------------------------------------------------------------------------- ERROR: backup_script /usr/local/backup_mysql.sh returned 1 WARNING: Rolling back "localhost/mysql/" ls -la /.snapshots/hourly.0/localhost/mysql total 8 drwxr-xr-x 2 root root 4096 Nov 23 17:43 ./ drwxr-xr-x 4 root root 4096 Nov 23 18:20 ../ What exactly am I doing wrong? EDIT: # /usr/local/backup_mysql.sh *** Dumping MySQL Database *** Database> information_schema..cphulkd..eximstats..horde..leechprotect..logaholicDB_ns1..modsec..mysql..performance_schema..roundcube..test.. *** Backup done [ files wrote to /.snapshots/tmp/mysql] *** root@ns1 [~]# ls -la /.snapshots/tmp/mysql total 8040 drwxr-xr-x 2 root root 4096 Nov 23 18:41 ./ drwxr-xr-x 3 root root 4096 Nov 23 18:41 ../ -rw-r--r-- 1 root root 1409 Nov 23 18:41 cphulkd.18_41_45pm.gz -rw-r--r-- 1 root root 113522 Nov 23 18:41 eximstats.18_41_45pm.gz -rw-r--r-- 1 root root 4583 Nov 23 18:41 horde.18_41_45pm.gz -rw-r--r-- 1 root root 71757 Nov 23 18:41 information_schema.18_41_45pm.gz -rw-r--r-- 1 root root 692 Nov 23 18:41 leechprotect.18_41_45pm.gz -rw-r--r-- 1 root root 2603 Nov 23 18:41 logaholicDB_ns1.18_41_45pm.gz -rw-r--r-- 1 root root 745 Nov 23 18:41 modsec.18_41_45pm.gz -rw-r--r-- 1 root root 138928 Nov 23 18:41 mysql.18_41_45pm.gz -rw-r--r-- 1 root root 1831 Nov 23 18:41 performance_schema.18_41_45pm.gz -rw-r--r-- 1 root root 3610 Nov 23 18:41 roundcube.18_41_45pm.gz -rw-r--r-- 1 root root 436 Nov 23 18:41 test.18_41_47pm.gz MySQL Backup seems fine.

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• Calendar booking issue - Exchange 2003 and 2010

  - by NaOH

  In our organization we are running Exchange 2003 and 2010 simultaneously, with the hopes of migrating everyone to Exchange 2010 sometime within the next few months. Everyone is using Outlook 2010. Recently, we had an issue with transaction log storage on the Exchange 2003 server. This was resolved, but for some reason no meeting rooms on the Exchange 2003 server will automatically book meetings any longer. I have played around with this for a while, changing calendar permissions, turning resource scheduling off and back on, etc. No dice. My next step was to try migrating a resource to the Exchange 2010 server. After doing so, and setting it up as a Room, enabling Auto-Accept and removing the EnableDirectBooking registry entry on my PC, I can book a meeting with this room. If EnableDirectBooking is enabled, I get an error message stating: "Meeting Room" declined your meeting because it is recurring. You must book each meeting separately with this resource. This is despite the fact that the meeting I'm attempting to create has no recurrence. Now, I have also created a new test Room from scratch on the Exchange 2010 server, and I can book a meeting with this Room regardless of whether or not I have the EnableDirectBooking reg entry in place. All users here have this registry entry, and I'd rather not have to figure out how to push something out to remove it from every PC. Rather, I'd like to figure out what's different between the configurations of these two meeting rooms so that I could book a meeting room regardless of whether EnableDirectBooking is enabled or not. Any ideas, anyone? Thanks!

  Read the article

• python mysqldb - mysql server gone away - can't reconnect

  - by david.barkhuizen

  When attempting to import a bunch of data into mysql tables using python and mysqldb, I run into the following error '2006 - mySQL Server has gone away', and then I am unable to reconnect again within the script. I am iniitially re-using a connection object across transactions ( delineated by conn.commit() ), then when I first encounter this exception, if I create a new connection by calling MySQLdb.connect(), this new connection also fails with the same exception. This error does not occur immediately, I can pump a fair amount of data into the db, but then faithfully occurs after I have inserted a couple thousand records, so roughly once the db has committed a certain transaction volume, it always falls over like this. If I rerun the script, WITHOUT restarting the db server. then it resumes where it left off, pumps in some data, then falls over again. Before recommendations to change time-out timings, does anyone know why I am not able to establish a new connection after the initial failure ? - Even if I try a couple of times waiting a couple of seconds between each. (btw, I'm running Windows 7, mysql server 5.1.48, mysqldb 1.2.3.gamma.1, python 2.6)

  Read the article

• Firefox proxy authentication with Kerberos: one service ticket per connection (Linux)

  - by Dari

  I am trying to enable proxy authentication via Kerberos for Firefox. The setup is: Active Directory domain (for LDAP and Kerberos; this works and I can log in the computer and get Kerberos tickets without problems) Microsoft Windows witness machine (on which Firefox runs fine with no ticket problem) CentOS 6.3 system with Firefox (the tests were performed with both the 10.0.1 ESR found in the CentOS package repositories and the 15.0.1 downloaded from Mozilla's website) BlueCoat proxy with Kerberos authentication enabled For the moment, Firefox requests an element of a website, gets an HTTP error code of "407 Proxy Authentication Required" from the proxy, gets a ticket granting service (TGS) from the domain for the proxy and performs the request again while passing the ticket. The transaction runs fine. However, when more elements are requested (in parallel), Firefox requests one more ticket per proxy connection. And this takes many DNS queries, Kerberos interactions with domain controllers and costs a lot of time (for example, the home page of Adobe takes several minutes to load and at the end, I have about 30 valid Kerberos tickets). I am stuck on this since a while, and help would be greatly appreciated. Minor information: the CentOS operating system is virtualized with VMware Player 3.1.3, but I do not think this would be a game changer.

  Read the article

• How should I perform database maintenance on a 24x7 system

  - by solublefish

  I'm a software developer who inherited a part-time DBA role. I'm responsible for an application backed by a small, high-volume 24x7 database on SQL Server 2008. While there's other stuff in the DB, the critical piece is a 50GB, 7.5M row table that serves 100K requests/sec during peak load, and about half that at "night". This is 99%+ read traffic, but the writes are constant, and required. I need to be able to perform periodic maintenance without a maintenance window. Say an index rebuild, a job to purge old data, Windows Update, or hardware upgrade. Most of the advice I've seen is along the lines of "MAKE a maintenance window." While I appreciate the sentiment, I hope there's another way. If it will solve this problem, I do have the ability to purchase new hardware or modify the database, the clients (a set of web services servers), and much of the application code (ADO.NET + ASP.NET). I've been thinking along the lines of using the warm spare (or a 3rd server) to do the maintenance, and then "swap" it into production. 1 Synchronize the spare by restoring backups, including a current transaction log. 2 Perform the maintenance tasks. 3 Reconfigure clients to connect to the spare server. Existing connections are finished within a minute or so. 4 The spare server is now the production server. The problem remaining is that the new production server is now out of date by however long it took to perform maintenance. Is there some way that the original production server can be made to queue up changes and merge them to the spare between steps 2 and 3? Any other ideas?

  Read the article

• Virus cleanup + dying drive = XP Automatic Updates crashing in esent.dll

  - by quack quixote

  Background I'm doing system recovery on an old WinXP SP1 system brought to me on suspicion of virus infection. After taking preliminary backups, I used MalwareBytes to detect and clean the infection. I might've even gotten it all. In the process, I've discovered (a) the system drive is showing signs of impending failure, and (b) the owner has been using the system's old crusty IE-6 instead of the up-to-date Firefox I've provided for him. So naturally, thinking I had a relatively stable system, I tried to hit the Windows Update site to install IE-8, in case further training doesn't stick. The update site told me it needed to update the installer, and I started that process. Soon after, wuauclt.exe started crashing, reporting addresses in module esent.dll. There's a Microsoft KB (910437) on a problem with that DLL, so I downloaded the hotfix and installed. The crashing did not stop. I attempted to install SP3 from the offline installer, but that didn't fix the issue either. The system is reporting a few hard drive / IDE controller errors, but they don't correlate to the crashes, so they aren't the direct cause. I've also attempted to rollback to the time between the infection removal and the first crashes, but that doesn't help. Question The hotfix I tried to install dealt with problem in transaction logs of the Extensible Storage Engine (ESE) database. I suspect this issue is similar, but that the database itself (whatever the ESE database is) is corrupted. Is there a way to clean or clear this database so that system operation returns to normal? Can someone enlighten me as to what the ESE database actually is, and where it resides? Can I just locate some files and delete them to bring this under control?

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

• Virus cleanup; Windows Automatic Updates service crashes in esent.dll

  - by quack quixote

  Background I'm doing system recovery on an old WinXP SP1 system brought to me on suspicion of virus infection. After taking preliminary backups, I used MalwareBytes to detect and clean the infection. I might've even gotten it all. In the process, I've discovered (a) the system drive is showing signs of impending failure, and (b) the owner has been using the system's old crusty IE-6 instead of the up-to-date Firefox I've provided for him. So naturally, thinking I had a relatively stable system, I tried to hit the Windows Update site to install IE-8, in case further training doesn't stick. The update site told me it needed to update the installer, and I started that process. Soon after, wuauclt.exe started crashing, reporting addresses in module esent.dll. There's a Microsoft KB (910437) on a problem with that DLL, so I downloaded the hotfix and installed. The crashing did not stop. I attempted to install SP3 from the offline installer, but that didn't fix the issue either. The system is reporting a few hard drive / IDE controller errors, but they don't correlate to the crashes, so they aren't the direct cause. I've also attempted to rollback to the time between the infection removal and the first crashes, but that doesn't help. Question The hotfix I tried to install dealt with problem in transaction logs of the Extensible Storage Engine (ESE) database. I suspect this issue is similar, but that the database itself (whatever the ESE database is) is corrupted. Is there a way to clean or clear this database so that system operation returns to normal? Can someone enlighten me as to what the ESE database actually is, and where it resides? Can I just locate some files and delete them to bring this under control?

  Read the article

• Delayed internet access

  - by Joel Coel

  When I (and presumably my users) first start up or log in to my computer I can't get internet access until several minutes after logging in. Internet pages like serverfault.com will time out. During this time I can access internal web servers. Sometimes pinging the gateway seems to fix the problem. I'm using Windows 7 on this machine with wifi, and the problem seems limited to the wifi network, which is on a separate vlan. The wired network does not share the problem, but I know it's not the wifi connection itself because the internal sites work. The wifi access point is attached to a 3Com 4200 switch, with the port set for vlan 2 untagged, vlan 1 tagged. The 4200 has a fiber connection to a 3Com 4900SX fiber switch that acts almost as a router here. The fiber connection is vlan 1 untagged vlan 2 tagged at both ends. The gateway is then attached to a different 4200 (vlan 1 untagged, vlan 2 tagged) that has a similar fiber connection to the 4900SX. vlan 2 has 192.168.8.0/22 IPs, vlan 1 has 10.1.0.0/16 IPs. The 4900SX has an interface for both vlans (10.1.1.1/192.168.8.1), as does the gateway (10.1.1.5/192.168.8.5). There is one dchp server for both vlans on the same switch as the gateway. It chooses a dhcp scope based on the interface used by the 4900sx to forward the dhcp request. There is also a network access list on the 4900sx set to deny all vlan2 traffic to any 10.1.x.x host, with exceptions made for a few servers, including dhcp, 4900sx, and the gateway. I think that about covers it. Any ideas on why internet access would be delayed like this?

  Read the article

• VNC Address Book - Window Invisible? Working as intended?

  - by user1445967

  I have VNC Server and VNC Viewer on the same PC with Windows 7 Ultimate x64. Is VNC Address Book supposed to have a main application window? I can't tell if this is bugged or working as intended. When I start VNC Address book, it creates an item in the task list and also an icon in the notification area. If I click the task list item once, nothing happens. If I click again, it disappears from the task list but remains in the notification area**. If I right-click the icon on the notification area, there is an option 'open address book', which if chosen, creates the item in the task list again, with the exact same behavior. If I left or right click on the address book icon, I have ways to connect to servers in the address book. However I have no way to add/remove/edit servers in the address book. **Note that this behavior is identical to that of an application with a main window where there is an option to 'minimize to system tray / notification area'. Only here, no main window is visible, ever. If fixing this problem is beyond the scope of this site, that's fine, but at this point I have no real way to tell if the program is malfunctioning on my pc or if it is far more minimalist than I expected. There appears to be no forum on realvnc.com where I can ask about this, perhaps this is to prevent me from getting any help unless I pay to register?

  Read the article

• Shortcut to "printer and faxes" on another computer

  - by Doltknuckle

  I have a print server running windows server 2008 that has about 50 printers on it. In windows XP, I was able to connect to the server using the UNC name and make a shortcut to the "printers and faxes" folder. (For the record, I know that it really isn't a folder, but that's outside the scope of this question.) I have recently switched to windows 7 and I find that the jump lists are really useful. One of the things I want to do is make it easy to connect to that server's "printers and faxes" folder. I would like to use something like a shortcut that I can open and go immediately to that location. The problem is that windows 7 doesn't have a way to create a shortcut like you could in WinXP. They have a button on the toolbar that says "view remote printers" which sends you to the correct folder. I'd like to avoid having to type out the server name. I also can't use the "view network" link in windows explorer. Our organization has over 6,000 machines and viewing the network lists all of them. This is all about saving time by using the minimum number of mouse clicks and key presses in normal operation. Does anyone have any suggestions?

  Read the article

• Apache2: Limit simultaneous requests & throttle bandwidth per IP/client?

  - by xentek

  I want to limit simultaneous requests & throttle bandwidth per IP/Client on a single apache vhost. In other words, I want to ensure that this site, which hosts large media files, doesn't get hammered by someone trying to download everything all at once (just happened the other night). I'd like to limit the outgoing transfer speed overall for this site, as well as limit the number of connections a single IP can make to the server to a sane default (i.e. within normal browser limits for multiple requests so page loads aren't effected too much). Bonus points if I can actually scope it to file types (i.e. leave web files alone, but apply these rules to just the media files). We're running Ubuntu 9.04 on all the servers, and have two apache/php servers being load balanced via Round Robin by a squid proxy server. MySQL is running on its own box as well. We've got plenty of bandwidth to give them, so I don't really want overall caps, but just want to throttle the amount of memory/CPU it takes to serve this site. There other sites on these servers that we don't want to apply these rules too, just want to keep this one from hogging all the resources. Let me know if you need more info! Thanks in advance for your suggestions!

  Read the article

• CentOS 5 : error in installing php-imap

  - by TMMDev

  can someone please help me with this CentOS 5 question? I am trying to install php-imap, i tried yum install php-imap but I am getting the following output: Loaded plugins: fastestmirror, priorities, security Loading mirror speeds from cached hostfile * base: centos.hostingxtreme.com * epel: mirror.steadfast.net * extras: mirror.team-cymru.org * updates: mirror.beyondhosting.net Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php-imap.x86_64 0:5.1.6-44.el5_10 set to be updated --> Processing Dependency: php-common = 5.1.6-44.el5_10 for package: php-imap --> Finished Dependency Resolution php-imap-5.1.6-44.el5_10.x86_64 from updates has depsolving problems --> Missing Dependency: php-common = 5.1.6-44.el5_10 is needed by package php-imap-5.1.6-44.el5_10.x86_64 (updates) Error: Missing Dependency: php-common = 5.1.6-44.el5_10 is needed by package php-imap-5.1.6-44.el5_10.x86_64 (updates) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package. I already have php-common installed, I ran "yum install php-common" and got the following output Loaded plugins: fastestmirror, priorities, security Loading mirror speeds from cached hostfile * base: centos.hostingxtreme.com * epel: mirror.steadfast.net * extras: mirror.team-cymru.org * updates: mirror.beyondhosting.net Setting up Install Process Package matching php-common-5.1.6-44.el5_10.x86_64 already installed. Checking for update. Nothing to do how can I fix this problem?

  Read the article

• Only tunnel certain applications via OpenVPN

  - by jinjin

  Hi, I've purchased a VPN solution, it works correctly when I have "redirect-gateway def1" in the configuration file (routing all traffic through the VPN). However when I remove that line from the configuration file, I am still able to ping-out of the machine (ping -I tap0), however I cannot ping the IP assigned to the machine (it's a public ip), i get the error: Destination Host Unreachable. I only want to have certain applications sending traffic through the VPN tunnel (eg: ZNC, irssi), all of which i can select which IP they use. However they can't recieve any data, making the tunnel essentially useless to me when disabling redirect-gateway. Any ideas on how to allow specific applications use the tunnel, without of forcing everything to go through it? My configuration file is as follows: dev tap remote #.#.#.# float #.#.#.# port 5129 comp-lzo ifconfig #.#.#.# 255.255.255.128 route-gateway #.#.#.# #redirect-gateway def1 secret key.txt cipher AES-128-CBC The output of ifconfig -a when the tunnel is connected: tap0 Link encap:Ethernet HWaddr 00:ff:47:d3:6d:f3 inet addr:#.#.#.# Bcast:#.#.#.# Mask:255.255.255.255 inet6 addr: <snip> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:612 errors:0 dropped:0 overruns:0 frame:0 TX packets:35 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:25704 (25.1 KiB) TX bytes:6427 (6.2 KiB) EDIT: the Bcast:#.#.#.# (ifconfig) is different from route-gateway #.#.#.# (openvpn) if that makes any difference.

  Read the article

• Suddenly getting lock timeouts with MySQL

  - by Marc Hughes

  We've got a web app hosted on Amazon Web services. Our database is a multi-az RDS MySQL server running 5.1.57 and 3-4 app servers talk to it. Today, we started seeing a lot of errors along the lines of "Lock wait timeout exceeded; try restarting transaction" - almost 1% of POST requests are seeing this. There have been no modifications to the code running on the site. There have been no schema changes. We haven't had a big spike in traffic. I've been looking at the processes running, and none seem out of control. I tried scaling our RDS instance from a small to a large, with no effect. Two days ago, Amazon had some outages. As part of the recovery from that, our RDS server, and our app servers ended up in different availability zones, but all within the same region. But yesterday, everything was fine so I'm not convinced that's related. The lock timeouts are in different types of requests and occur in different InnoDB tables. I have noticed the number of open connections jumped when we started seeing problems, but they may be a symptom and not a cause. What are my next steps in debugging this?

  Read the article

• MySQL slave server from dumps

  - by HTF

  I've created a slave server from live machine which is acting as a master now. I use the following procedure to create it: mysqldump --opt -Q -B --master-data=2 --all-databases > dump.sql then I imported this dump on the new machine, applied the "CHANGE MASTER TO..." directive with a log file/position from the dump. Please note that I have around 8000 databases and I didn't stop the master while the dumps were running. The replication works fine but is this a properly method for creating a slave server? I'm planning to promote this slave to a master (different location) so I would like to make sure that there is a 100% data consistency between the servers. I've found this article where it says: The naive approach is just to use mysqldump to export a copy of the master and load it on the slave server. This works if you only have one database. With multiple database, you'll end up with inconsistent data. Mysqldump will dump data from each database on the server in a different transaction. That means that your export will have data from a different point in time for each database. Thank you

  Read the article

• SQL 2008 R2 replication error: The process could not connect to Distributor

  - by Lance Lefebure

  I have two servers running SQL 2008 R2 Standard, each with an instance named "MAIN". I have a small test database on my primary server (one table, 13 rows) that I want to replicate to a second server as a proof-of-concept for some larger databases that I want to replicate. I set up the primary server to be a publisher and distributor, and set the database to do transactional replication. I copied the data to the second server via a backup/restore, not via a snapshot (which I'll have to do with the larger databases due to database size and limited bandwidth). I followed the instructions here: http://gnawgnu.blogspot.com/2009/11/sql-2008-transactional-replication-and.html Now on the subscriber, I go under Replication / Local Subscriptions / Right click / Properties on my subscription to the DB. The status of the last synchronization shows a status of: "The process could not connect to Distributor 'PRIMARYSERVER\MAIN'." Data IS replicating from the primary to the secondary. Any record I add on the primary shows up on the secondary server within seconds. Is the Distributor part of the Snapshot system that I'm not using, or is it part of the transaction replication stuff? Thanks, Lance

  Read the article

• On Windows machines, what is the typical toolchain for remote maintenance?

  - by Hanno Fietz

  I need to deploy PHP and Python code and the appropriate environment (web server, db server) to remote Windows systems, and I don't know what toolchain would be the equivalent to ssh, scp, bash and the like. So, basically, what I need to be able to do is the following: access remote Windows with the appropriate privileges in a secure manner, like I routinely do with ssh (I don't even know whether that would be a text or graphic interface on Windows). remotely install software: Apache or IIS, MySQL or Postgres, Python or PHP copy files from remote (the application we're deploying) remotely configure the machine to run regular tasks (e. g. checking for updates to the application) automate tasks like downloading files from a designated place The main question is probably how I get onto the machine securely in the first place, and then the rest is general Windows admin knowledge, which probably is too broad a scope to fit into one question. I have years of experience with maintaining Linux boxes and I have used tools of varying sophistication on those, ranging from plain scping of PHP files to deployment of Java application containers and even full VMs with Vagrant. On Windows, I'm a complete noob, and I don't even know where to start. I have installed Apache, MySQL , PHP on a desktop machine maybe twice in my life, that's about it. Bonus points for things that work from a Linux machine at my end, but I could run a VM and do everything from there.

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >