Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 163/286 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

  • Set up Linux box as WAP for MyBookLive?

    - by AcidFlask
    I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

    Read the article

  • DHCP Relay setup in ubuntu server

    - by jerichorivera
    I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

    Read the article

  • Variable TTL inside a LAN

    - by user140783
    I recently discovered that ping my local router, returns different TTL values??. The ping 3 switch must pass through before reaching the router, there may be the problem? 192.168.1.99 is the IP of my router , a Cisco WRT120N Thank you! Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=190 Respuesta desde 192.168.1.99: bytes=32 tiempo=29ms TTL=3 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=117 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=131 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=111 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=240 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=51 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=190 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=66 Traceroute G:\Documents and Settings\Administrador>tracert 192.168.1.99 Traza a la dirección maxi2011 [192.168.1.99] sobre un máximo de 30 saltos: 1 <1 ms <1 ms <1 ms maxi2011 [192.168.1.99] Traza completa. G:\Documents and Settings\Administradorping 192.168.1.99 Haciendo ping a 192.168.1.99 con 32 bytes de datos: Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=190 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=190 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=117 Respuesta desde 192.168.1.99: bytes=32 tiempo<1m TTL=117 Estadísticas de ping para 192.168.1.99: Paquetes: enviados = 4, recibidos = 4, perdidos = 0 (0% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms G:\Documents and Settings\Administrador

    Read the article

  • Wake on Lan Remote not waking PC while the PC does receive the packet.

    - by Nycrea
    Over the last couple of weeks, I have been trying to set up WOL from a remote location. When I use my laptop to wake the machine locally, it works just fine. (for some reason, when I try to wake from my phone with an app called "WOL wake on lan" it does not work locally either, but I'll get to that later) Anyway, when the machine is turned on, and I let it 'listen' for incoming magic packets (with a program called "WOL magic packet sender") on my specified port, it does receive them, though when turned off, the machine does not wake. When sending from phone, either locally or via 3G remotely, it does receive but does not wake as well. Because the machine does receive them when turned on and listening, but does not wake when turned off, I am convinced the cause of the problem is my receiving PC, rather than the router or the sender. Some extra info: The receiving machine is a PC running Windows 7 64bit. My router is the Netgear JWNR2000v2. I have the port I use forwarded to my PC's static IP in the router. If anyone could help, or just share your own story with the same problem, maybe we can work this out. Thanks a lot in advance.

    Read the article

  • Blocking of certain file downloads

    - by Philip Fourie
    I have a problem where I cannot completely download a certain file from a server. The file is 1.9MB in size but only 68% is downloaded and then it hangs. I tried and these cases, which failed: Downloaded the file with HTTP Downloaded the file with FTP Moved the file to different FTP and web servers behind the ISA firewall Tried with IIS 6.0 & IIS 7.0 Multiple download clients. Which included FireFox, FileZilla (on Windows) and wget (on Linux) This worked: Downloading other files from the same location on the server. Both bigger and smaller and in size than the original. FTP and HTTP worked. Earlier version of this file (.DLL) works. It is as if the content of this file has an influence on this file being served. Network architecture: Client Machine - Internet (ISP) - ISA Server - IIS 7.0 The only constants are the ISP, Cisco router and the ISA server. Is it possible that something is rejecting the download because of the contents of the file? I am hoping ISA is the culprit... I am not a ISA expert is there somewhere I can look to establish if it is indeed ISA causing this? Update: Splitting the file into two parts with a hex editor results in one half of the file being served correctly and the other part not. Zipping the file results in the file being downloaded successfully. However this is not an option for this particular scenario. Renaming the file and its extension also doesn't work. Update 2009/10/22: It does NOT seems to be ISA that is causing this problem. We connected a laptop (running IIS) on an available public IP and still the file download to 68% before it hanged. The two remaining components are the ISP and the Cisco 800 series router. Anyone knows about an issue on the router perhaps?

    Read the article

  • Vmware Workstation, Win7 host, Ubuntu guests with Nat + Host-only networks but they cannot connect to the Internet

    - by Ikon
    I have a Win7 host machine with Vmware Workstation. In the workstation I have 3 Ubuntu installed. All 3 Ubuntu guests have a Nat network - to access the internet without asking the router for a local address - and a Host-only network - to connect all Ubuntu quests and the host in a private network for internal communication, without touching the router. When I try to make any of the Ubuntu quests to get data from the internet - assuming that they would figure out that the Nat-ed interface can access the requested data - they fail and report that there is no route to my query. If I disconnect the 2nd interface on the Ubuntu guests with the Host-only network and restart networking, they start to know the route to the internet. Odd, during the installation of the guests they asked which of the 2 given interfaces - with Nat and Host-only config - should be used to get updates during installation and they oddly managed to get the updates. Not so after the installation has finished and rebooted. I have checked the Virtual Network Editor that the Nat interface should use my real network card to access the net, so there should be no problem. I wish not to use the router's dhcp service to give the Ubuntu quests an address, and also I don't want the guests to be accessable from the local network directly, but only by the host - that's the Host-only network is for. Any suggestions? Edit: 192.168.189.0 is the Nat interface and 192.168.7.0 is the Host-only. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.7.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.189.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.189.2 0.0.0.0 UG 100 0 0 eth0

    Read the article

  • Find routers IP address on the other side

    - by corsiKa
    Here's the basic setup of my network In this diagram: 1: The internet c: cable 2: Wireless router w: wireless connection 3: A win7 box with internet connection sharing enabled 4: A wireless router, but I'm only using its LAN capabilities to connect box 5 to the internet. 5: A win7 box, the computer I'm using to make this post. So its internet works just fine. Now if I'm on box 5, and I ping 192.168.1.1, I hit 4. If I'm on box 3 and I ping 192.168.1.1, I hit 2. Now obviously box 3 does not think 4's IP address is 192.168.1.1, or I wouldn't be able to connect to the internet. Okay, now that you know as much as I do about my network, here's my question: If I was on box 3, how would I determine the IP address of 4? Basically I'm running a webserver on box 5 and want to access this webserver on box 3 and other boxes. So that's the end goal. If there's other information there that can help, I'd appreciate it. Thanks!

    Read the article

  • How to set a static route for an external IP address

    - by HorusKol
    Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

    Read the article

  • .htaccess with godaddy not working in subdomain

    - by explorex
    Hi, i have a site uploaded to shared subdomain (which is inside a folder). and htaccess is not working. please get details from here. EDIT::copied from stack overflow Hi, i uploaded as website to a subdomain, and every page is not working except the front page please check it here. what could be the possible reason? i shoud have 8 pages in front level and many more on admin level but i am getting 404 error as you can see, does anyone has idea or suggestion? UPDATE:: .htaccess file RewriteEngine On RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] RewriteRule ^.*$ index.php [NC,L] UPDATE to url rounting i do have few url router like below BUT i dont have any default router $router->addRoute( 'get-destination', new Zend_Controller_Router_Route('destination/get/:id/:dest-name', array( 'controller' => 'destination', 'action' => 'get', 'id' => 'id', 'dest-name' => 'dest-name' )) ); just to make look cooler and on my navigation (which is loaded from xml i have) something like <nav> <home> <label>HOME</label> <controller>index</controller> <action>index</action> <route>default</route> </home> since i was getting url problem from where url was routed and please check phpinfo at http://websmartus.com/demo/globaltours/public_html/phpinfo.php

    Read the article

  • VMware Workstation Bridged Network Host UnReachable

    - by user2097818
    VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

    Read the article

  • Port(s) not forwarding?

    - by user11189
    I have cable internet service through Charter Communications and feed two desktop computers through a Linksys RP614v3 router. One system is my wife's running WinXP Home Edition and the other is mine, running Vista Home Premium (sp1). I have port forwarding configured in the Linksys so I can access the Vista system remotely using TightVNC. Initially, it worked great and I was able to remotely tend email and access local files while out of town for work. Lately, the cable internet service appears to flicker intermittently and upon return, my Mailwasher program loses ability to access the net and I've been unable to make the remote connection. When I reset the port forwarded for email in the router control panel, Mailwasher functionality returns but as I'm home when that happens, I have no easy way to check remote access until the next time I'm on the road or at work. I'm at my wit's end -- the TightVNC client accesses fine from my wife's system from behind the modem/router setup but I don't know how to maintain whatever gets reset when I fiddle with the control panel and the need to do so at all is new. I accessed it fine for a week off and on while out of town a month ago and now I can't leave home and access it from work an hour later.

    Read the article

  • SBS 2008 - DNS Forwarders timing out.

    - by Moif Murphy
    Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

    Read the article

  • Cant ping ip on LAN. Port forward works fine though.

    - by Anoop
    I have a Solaris 11 machine running inside the LAN. It is a default install. I can access the machine and ping it if I ssh into my router (if it matters, it is running dd-wrt). I cannot ping the Solaris machine using ip address from any other machine inside the LAN. But if I setup port forwarding everything works perfectly fine. I can also use the port forward from outside the LAN (from my office) - which is good and how I want it to be. I can SSH and ping and do pretty much everything else from outside as well as inside but only as long as I have the port forwarded from my router. Why would I not be able to ping or ssh or even access the Solaris 11 machine from within the LAN - I have checked and couldn't find any firewall running on the Solaris 11 box. I even tried disabling every known firewall on the router (dd-wrt, it had something like SPI firewall running). I even tried setting a static IP for my Solaris box but all in vain! Please help me understand how and why this happens!! Thanks.

    Read the article

  • Servers - Buying New vs Buying Second-hand

    - by Django Reinhardt
    We're currently in the process of adding additional servers to our website. We have a pretty simple topology planned: A Firewall/Router Server infront of a Web Application Server and Database Server. Here's a simple (and technically incorrect) diagram that I used in a previous question to illustrate what I mean: We're now wondering about the specs of our two new machines (the Web App and Firewall servers) and whether we can get away with buying a couple of old servers. (Note: Both machines will be running Windows Server 2008 R2.) We're not too concerned about our Firewall/Router server as we're pretty sure it won't be taxed too heavily, but we are interested in our Web App server. I realise that answering this type of question is really difficult without a ton of specifics on users, bandwidth, concurrent sessions, etc, etc., so I just want to focus on the general wisdom on buying old versus new. I had originally specced a new Dell PowerEdge R300 (1U Rack) for our company. In short, because we're going to be caching as much data as possible, I focussed on Processor Speed and Memory: Quad-Core Intel Xeon X3323 2.5Ghz (2x3M Cache) 1333Mhz FSB 16GB DDR2 667Mhz But when I was looking for a cheap second-hand machine for our Firewall/Router, I came across several machines that made our engineer ask a very reasonable question: If we stuck a boat load of RAM in this thing, wouldn't it do for the Web App Server and save us a ton of money in the process? For example, what about a second-hand machine with the following specs: 2x Dual-Core AMD Opteron 2218 2.6Ghz (2MB Cache) 1000Mhz HT 16GB DDR2 667Mhz Would it really be comparable with the more expensive (new) server above? Our engineer postulated that the reason companies upgrade their servers to newer processors is often because they want to reduce their power costs, and that a 2.6Ghz processor was still a 2.6Ghz processor, no matter when it was made. Benchmarks on various sites don't really support this theory, but I was wondering what server admin thought. Thanks for any advice.

    Read the article

  • LAN Webserver not accessible through PPTP VPN

    - by Joe
    I have this LAN Network with 10 clients and one server. The server has 4 virtual machines and a BIND DNS Server. When the router assigns an IP through the DHCP , it also gives the ip of the DNS Server, to resolve internal domains. Everything apparently works fine, the clients being able to access the server's vm's resources, but I also have to create the possibility of remote access. I installed the PPTP VPN on the server, and the vpn clients would get the same ip address range as the router's dhcp is assigning. Apparently everything is fine here also, except the fact that when we connect through the vpn , we cannot access the webserver on port 80 ( the webserver being one of the server's VM ). The iptables on the webserver has been turned off for testing purposes and the router's firewall is directing all the external traffic to the server. Can somebody suggest a solution to this? Extra details : VPN Server : PPTP Server Centos 6.3 x64 VPN Client : Windows 7 default PPTP VPN Connection The client is successfully connected to the server, everything works ( FTP/MYSQL/SSH/DNS ) , except the fact that when I try to access the webserver IP on the browser, it won't work.Pinging it works perfectly.

    Read the article

  • Problem with connecting two different networks

    - by tanascius
    I have two networks: 192.168.13.0/24 (blue) and 192.168.15.0/24 (green). Computer A is connected to the 13-net, only. Computer B has two interfaces, one in each network. There is third computer that acts like a router and connects the 13-net to the 15-net (only in this direction). Now, I'd like to ping 192.168.15.100 from computer A to B. Unfortunately there is never a reply. But when I use a hub instead of a switch it works. In my opinion the ping packet travels through the switch to the router (which is the default route/gateway for A). The router sends the packet back to the switch to B. Probably B receives it on its 15-net interface but answers with it's 15th interface? Is this possible? The problem is, that B may have only a gateway 192.168.13.50 - but I am not really sure of it (B is a embedded system with limited configuration possibilities). Can anyone explain what happens here? Thank you!

    Read the article

  • Setting up a home network

    - by Mat Richardson
    I'm trying to get my head around how to do this with the equipment I have. Here's how it is.. I have an old laptop that has server 2003 installed on it. This has no wireless NIC, but I have a spare wireless router that I can wire to it. We have a virgin wireless router which provides the home with internet access. What I would like to do it make resources on the server 2003 machine available to the rest of the devices in the home - specifically a couple of laptops running windows 7. Ideally I'd like to be able to use the laptop as a fileserver but maybe also offer application virtualization. In the first instance however, I'd like to create a file server with the laptop and allow connections to it by the other machines. Virtualisation is just a 'nice to have'... Given the hardware I have is this possible? Can you point me in the right direction how to do what I want if this is the case?

    Read the article

  • Remotely port forward/launch process or a client-less remote desktop app?

    - by DC177E
    I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

    Read the article

  • Need to set up a proxy on Linksys E3200 to filter home internet

    - by Justin Amberson
    the fact that I have a Linksys E3200 may not be important. I can configure the router through the web interface, but I don't know the things I will be toggling are called. I already do simple port forwarding to access applications on my Mac remotely. So router admin is not something I technically need explained. I'm looking to running a proxy on my home computer, that filters all HTTP traffic that goes through my router. So if my daughter is on her iPad and accesses Safari, my Mac will be the judge of the validity of the request. I need something like NetNanny I guess, but local. Actually, anything that can just filter all port 80 traffic that runs locally, but maybe validates with a password? I truly truly hope this question falls within the bounds of Serverfault. I'm not a total internet newb but I'm at a loss for what to Google. If possible answer this question: Is there a webapp that can listen on port 80, and validate requests to port 80 with a password? If so, can I forward all traffic on port 80 to my Mac, to be re-routed to the user? Is this the same as a VPN? Thank you for your help. Justin

    Read the article

  • Static DHCP binding

    - by Alex
    Good time of day, SF people. I have created a manual DHCP binding entry on a Cisco router so that a client would always get leased to it. The clients wants to get the same address on both of his dual-boot linux systems. He tries to get an IP address leased and he succeeds on one of the dual-boot operating systems. When he reboots to another one he gets a lease for a completely different one. I don't get it. The MAC addresses are the same (we checked in ifconfig, so what could be happening here? Why is the router confused? Or is it something else? Also, how can I check DHCP server IP address who I have got an IP address from (on Linux)? Configuration on Cisco: ip dhcp pool MANUAL_BINDING0001 host 192.168.0.64 255.255.255.0 hardware-address dead.beef.1337 dns-server 192.168.8.11 default-router 192.168.0.254 domain-name verynicedomainigothere.cn PS. Is it mandatory to use client-name configuration line?

    Read the article

  • Why would my network slow down?

    - by monkthemighty
    The network at my work has about 40 computers on it and a quite a few printers. When there are a lot of people working the network will be slow. I can test the ping between my computer and the router and it will keep rising, sometimes to the point that it times out. The router we are using is running Ubuntu on a atom processor and it has 4gb of ram. When the network slows the process Ksoftirq will be using most if not all of the processing power. I have found that Ksoftirq is a process that handles irq requests. Also when the network slows down I have captured packets from the router and using tshark and looked at it using wireshark on my laptop. With the capture show a lot of packets with TCP Dup ACK and TCP Retransmissions. The destinations of the TCP Dup and TCP retransmissions are to most of the computers on the network but there are some that are far more than others. What could this problem be caused by?

    Read the article

  • Convert Console Output to Array

    - by theundertaker
    Using netsh wlan show networks mode=bssid on Windows CMD yields a listing of available wireless networks. Is it possible to convert the list, which looks something like this: Interface name : Wireless Network Connection There are 11 networks currently visible. SSID 1 : Custom Gifts Memphis Network type : Infrastructure Authentication : Open Encryption : WEP BSSID 1 : 00:24:93:0c:49:e0 Signal : 16% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 6 9 12 18 24 36 48 54 SSID 2 : airportthru Network type : Adhoc Authentication : Open Encryption : None BSSID 1 : 62:4c:fe:9c:08:18 Signal : 53% Radio type : 802.11g Channel : 10 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 3 : belkin.ffe Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 08:86:3b:9c:8f:fe Signal : 23% Radio type : 802.11n Channel : 1 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 4 : 3333 Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 00:0f:cc:6d:ba:ac Signal : 18% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 22 24 36 48 54 BSSID 2 : 06:02:6f:c3:06:27 Signal : 20% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 5 : linksys Network type : Infrastructure Authentication : Open Encryption : None BSSID 1 : 98:fc:11:69:35:46 Signal : 38% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 6 : iHub_0060350392e0 Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 00:c0:02:7d:5f:4e Signal : 18% Radio type : 802.11g Channel : 11 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 7 : TopFlight Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 00:14:6c:7a:c4:70 Signal : 16% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 8 : 2WIRE430 Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : b8:e6:25:cb:56:a1 Signal : 16% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 9 : LUBIN Network type : Infrastructure Authentication : WPA-Personal Encryption : TKIP BSSID 1 : 00:13:10:8d:a7:32 Signal : 65% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 10 : TV2 Network Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : b8:c7:5d:07:6e:cf Signal : 79% Radio type : 802.11n Channel : 11 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 11 : guywork Network type : Infrastructure Authentication : Open Encryption : WEP BSSID 1 : 00:18:e7:cf:02:20 Signal : 15% Radio type : 802.11n Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 ... into an array using JavaScript or C#? I know it is but it seems like it may be rather difficult. Are there other avenues of obtaining such network information in the requested format? A JavaScript object would be perfect.

    Read the article

  • Windows 7 Status Menu style Window

    - by Mason Blier
    Hey all, I'm working on a project and I'm wondering how to get a type of window common in Windows's wireless controls, as shown in the screen shot below: http://cybernetnews.com/wp-content/uploads/2008/10/windows-7-wireless.jpg There's no close or maximize buttons, but the border is still present. My tools include Expression Blend 3 and Visual Studio 08. I was also wondering what the font used on these are, as it doesn't seem to be the normal Tahoma found in Office 7. Thanks, Mason

    Read the article

  • Other than UDP Broadcast or Multicast, what other methods can I use on a WiFI network to discover co

    - by Gubatron
    I've implemented a simple ping/pong protocol to discover other computers connected to the same WiFI router. This works fine on many routers, but it seems some public routers have UDP traffic blocked or disabled. What other options do I have to discover the computers connected to the router? I was thinking of brute forcing TCP attempts (trying to open connections to all possible IPs on my subnetwork) but this would be very costly and I would have to cycle several times and still not find every machine that's recently connected to the network.

    Read the article

  • How do I create a custom network connection entry?

    - by David Brown
    I have a Sprint MiFi 3G router that exposes its current signal strength over HTTP. I've developed a very simple tray application that displays this. However, what I would really like to do is create a custom network connection entry so the router's 3G signal strength (along with the current network version) displays when clicking on the network connections tray icon (in Windows 7, at least). Is it possible to do this with a shell extension or something (preferably in C#)? If so, how?

    Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >