Search Results

Search found 5464 results on 219 pages for 'j random hacker'.

Page 164/219 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

• Router reporting failed admin login attempts from home server

  - by jeffora

  I recently noticed in the logs of my home router that it relatively regularly lists the following entry: [admin login failure] from source 192.168.0.160, Monday, June 20,2011 18:13:25 192.168.0.160 is the internal address of my home server, running Windows Home Server 2011. Is there anyway I can find out what specifically is trying to login to the router? Or is there some explanation for this behaviour? (not sure if this belongs here or on superuser...) [Update] I've run both Wireshark and netmon for a while on my home server. Wireshark captured the traffic, but didn't really show anything useful (or nothing I could make use of). A simple HTTP GET request is sent from the server (192.168.0.160) to the router (192.168.0.1), from a seemingly random port (I've seen examples from 50068, 52883), and it appears to do it twice in quick succession (incrementing port by 1), about every hour. Running netstat around the time of the failure didn't show anything (probably too long after anyway). I tried using netmon as it categorises by process, so I thought it might show a corresponding process for the port. Unfortunately, this comes in under the 'unknown' category, meaning it's basically just a slower, less useful Wireshark. I know there's not much to go on here, but does this help in anyway?

  Read the article

• Nginx proxy to IIS Connection Timeout

  - by MitMaro

  I am having an issue with random timeouts with a Nginx proxy connecting to an IIS machine. I have been watching a packet capture between the two servers and it seems that the IIS machine is receiving a SYN packet but is not responding with what I think should be an ACK response. Before the timeout occurs there seems to be a slower response from the IIS server. There is no unusual memory or processor usage on the IIS or Nginx machine. Some information on the servers and setup: Nginx Machine: Ubuntu 10.04 64bit Nginx 0.7.65 Amazon EC2 Windows Machine: Windows Server 2008 IIS 7 ASP.net Application in Integrated Mode Nginx Error: 2011/01/10 17:57:40 [error] 8297#0: *30 connect() failed (110: Connection timed out) while connecting to upstream, client: 209.***.***.***, server: secure.example.com, request: "GET /a/path/deliver.aspx HTTP/1.1", upstream: "http://***.***.***.****:****//another/path/deliver.aspx", host: "secure.example.com" WireShark Packets 6521.449528 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477422103 TSER=0 WS=7 6524.443239 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477422403 TSER=0 WS=7 6530.443241 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477423003 TSER=0 WS=7

  Read the article

• Hardware issue, bsod with windows xp irq and strange messages with ubuntu

  - by JP Hellemons

  I have an old Acer T160 and it used to run Windows XP. But I keep getting random BSOD's. I keep seeing IRQ conflicts. I tried to run ubuntu, which runs and keeps running. But sometimes is not responding. Also there are these popups at ubuntu 12.04 that my network cable (which is onboard) is unplugged. But I have no cable in it! and have an usb dongle for wifi. which also seems unstable. have to (auto)reconnect sometimes. So my question is: is it my mobo, power supply or something else? FYI: I had an dvd-rw station which did not open properly, so unplugged the ata and power, als removed the second harddrive. now only have sata harddrive. also removed the extra video card (ati sapphire x1600 pro) so use only onboard video now and still have these issues. EDIT Update: will try with a new PSU (power supply unit of 400watt) the old (factory) one was 300watt. and will use a usb drive which has 12.04 ubuntu on it (made with unetbootin) to format everything and re-install ubuntu. (so also delete mbr partition) will update the day after tomorrow.

  Read the article

• How can I remedy the always-on-top window problem?

  - by GateKiller

  Sorry for the vague title but this one is hard to explain so bear with me please. I'm using Windows Vista at work for web development and sometimes when I Click or Alt-Tab to background window, the window will get focus but it will not be brought to the front. In order to bring the window to the front, I have to click on the applications border (when the resize cursor appears) and the window will then jump to the front. I've had this problem for about a year now and it happens at least a dozen times a day, but it doesn't do this all the time - seems random. I hope I have explained the issue fully (and you've understood it) and would appreciate any constructive answers or comments to solve this problem. Example: If I Alt-Tab from Google Chrome to Notepad and this problem randomly occurs, Google Chrome will remain in front of Notepad, however, I will be able to type text into Notepad while the window is behind Google Chrome. Clicking on Notepad's content area will not bring it to the front but clicking it's window border will. Video Exampe http://vimeo.com/19388998 In this video, I clicked from Google Chome to UltraEdit and chrome stayed in font, but as you can see, I can still type in UltraEdit. I'm starting to believe that this could be a bug in Google Chrome so I'll continue to watch if this between other applications.

  Read the article

• How I can fix the "Display Driver has stopped responding and has recovered"?

  - by Vitor Rangel

  I'm using a GeForce GTX 580, with Windows 7 64-bit. The driver version of the GTX is 301.42. The problem happens after a few minutes, when I'm playing specifc games. It won't happen in all games - And I don't have any idea why these games doesn't work. The games that doesn't work: Battlefield 3, Civilization V, Sniper Elite V2. The games that work: Mass Effect 3, Crysis 2, Team Fortress 2, Left 4 Dead 2, Skyrim, L.A. Noire. As you can see, it's not a problem of "The games that demand more stop working". I've tryed updating the driver of the graphics-card, the bios of the motherboard, even formated my computer (It was needing it) and instaled every driver in the last version possible. This problem happens since I bought my graphics-card, 6 months ago. After a few minutes, from 10 to 20, the pixels in the monitor become strange, with random colors and effects, like it was broken. Then, everything goes black, and the message appears "Display Driver has stopped responding and has recovered". After that, I need to close the game and start again. I am not overclocking, and my temperature never goes higher than 70ºC.

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Recover badly recorded DVDs

  - by CesarGon

  A few years ago (2003-2005) I bought a Sony USB external DVD recorder for my Dell laptop and I used it to burn a lot of discs. Much later, when I tried to use one of these discs, I realised that I could not read it. The disc behaved as if it was scratched or dirty. I tried on a couple of different DVD drives but got the same effect. Sadly, all the discs that I burnt with that recorder suffer from the same problem. Edit. When I read one of these discs with ImgBurn, I get lots of unrecovered read errors in multiple sectors, even at 1x speed. The sectors that cause read errors seem to be quite random; it's not always the same one. I have no idea what could be wrong with the discs. I doubt that they are scratched or dirty; it would be too much of a coincidence that all the discs that I burnt with that recorder got damaged at the same time. Also, they don't show any physical defects. Is there any way to diagnose what the problem is and, hopefully, recover the contents of the discs? Many thanks.

  Read the article

• jdbc4 CommunicationsException

  - by letronje

  I have a machine running a java app talking to a mysql instance running on the same instance. the app uses jdbc4 drivers from mysql. I keep getting com.mysql.jdbc.exceptions.jdbc4.CommunicationsException at random times. Here is the whole message. Could not open JDBC Connection for transaction; nested exception is com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: The last packet successfully received from the server was25899 milliseconds ago.The last packet sent successfully to the server was 25899 milliseconds ago, which is longer than the server configured value of 'wait_timeout'. You should consider either expiring and/or testing connection validity before use in your application, increasing the server configured values for client timeouts, or using the Connector/J connection property 'autoReconnect=true' to avoid this problem. For mysql, the value of global 'wait_timeout' and 'interactive_timeout' is set to 3600 seconds and 'connect_timeout' is set to 60 secs. the wait timeout value is much higher than the 26 secs(25899 msecs). mentioned in the exception trace. I use dbcp for connection pooling and here is spring bean config for the datasource. <bean id="dataSource" destroy-method="close" class="org.apache.commons.dbcp.BasicDataSource" > <property name="driverClassName" value="com.mysql.jdbc.Driver"/> <property name="url" value="jdbc:mysql://localhost:3306/db"/> <property name="username" value="xxx"/> <property name="password" value="xxx" /> <property name="poolPreparedStatements" value="false" /> <property name="maxActive" value="3" /> <property name="maxIdle" value="3" /> </bean> Any idea why this could be happening? Will using c3p0 solve the problem ?

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• configure a Macbook Pro to use external monitor at boot (Debian Linux)

  - by Eric

  In the spirit of reuse, I've installed Debian (version 6.0.5 "squeeze") on my wife’s old Macbook Pro (circa 2009 or so), to repurpose it for various tasks. The catch is the display is flaky. It will last a random amount of time, between 2 minutes and 2 hours, before freezing and graying out. This is a known issue with that generation of MBP. Fortunately it’s no problem for me, as I plan to use it with an external monitor anyway. Which brings us to the problem: How do I configure this thing to output to the external display by default, and hopefully disable the built-in LCD? The ideal solution would be to modify a setting in the EFI (BIOS), but I’m not holding out much hope for that. Next best thing would be a kernel option I can pass to the NVIDIA driver. What won’t work is a solution that doesn’t give me a display until X starts. I need to have console access, especially given that the built-in LCD is dying, and any day now might give out completely. So far I haven’t been able to find anything online. lspci says I’ve got an NVIDIA GeForce 9400M Help is much appreciated! Eric PS if this question is better suited to the Unix & Linux area, pls advise and I will move it.

  Read the article

• Understanding Microsoft Word Formatting Behavior. Does anyone?

  - by deemer

  This isn't a question about how to do something (well, not directly), but rather an inquiry to see if anyone understands why MS Word behaves the way it does with respect to formatting from a design perspective. This is also admittedly a rant about Word. This is a question that has plagued me, well, every time I open a document in Word, and covers a lot of individual topics, so I'll restrict the discussion here to two concrete behaviors that baffle me. 1) Backspacing over whitespace changes the format of preceding text. This seems to most often occur when the preceding text is a header or list number. The strangest thing about this is the new format of the changed text usually doesn't appear anywhere else in the document. 2) Numbered lists count almost at random. I am working on a document today where the list numbers count as follows: 1, 2, 2, 3, 3. The lettering in the sublists go like this 1: a, 2: a, 2: b c d, 3: e f g, 3: a. Clicking on each number or letter highlights the other numbers or letters that Word thinks it is related to, which are scattered around the document pretty heavily. Attempts to renumber the list have so far proven fruitless, as Word seems to maintain these associations through clipboard copies, etc. Why could this even happen?

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• To what extent is size a factor in SSD performance?

  - by artif

  To what extent is the size of an SSD a factor in its performance? In my mind, correct me if I'm wrong, a bigger SSD should be, everything else being equal, faster than a smaller one. A bigger SSD would have more erase blocks and thus more leeway for the FTL (flash translation layer) to do garbage collection optimization. Also there would be more time before TRIM became necessary. I see on Wikipedia that it remarks that "The performance of the SSD can scale with the number of parallel NAND flash chips used in the device" so it seems throughput also increases significantly. Also many SSDs contain internal caches of some sort and presumably those caches are larger for correspondingly large SSDs. But supposing this effect exists, I would like a quantitative analysis. Does throughput increase linearly? How much is garbage collection impacted, if at all? Does latency stay the same? And so on. Would the performance of a 8 GB SSD be significantly different from, for example, an 80 GB SSD assuming both used high quality chips, controllers, etc? Are there any resources (webpages, research papers, presentations, books, etc) that discuss correlations between SSD performance (4 KB random write speed, latency, maximum sequential throughput, etc) and size? I realize this does not really sound like a programming question but it is relevant for what I'm working on (using flash for caching hard drive data) which does involve programming. If there is a better place to ask this question, eg a more hardware oriented site, what would that be? Something like the equivalent of stack overflow (or perhaps a forum) for in-depth questions on hardware interfaces, internals, etc would be appreciated.

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  EDIT: I can only mark one answer as the correct one but the actual solution was a combination of two comments (updating the BIOS to A15 AND installing the Sigmatel audio drivers). I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

• What Windows app can sort a huge XML file?

  - by Torben Gundtofte-Bruun

  I have some enormous XML-based configuration files, with 125000 lines in them. The problem is that they are auto-generated by the system I use, and "child" tags are in a random order within their respective parent tag. This means that a diff comparison is impossible. I want to recursively sort all tags within a parent tag by the value in name="". Some parent tags only appear once and don't have a name="" parameter; these should be sorted by the tag name itself. Once the files are sorted like this, they can be compared quite easily using normal tools. We are currently using ExamXML which can match unsorted XML files, but it fails because the files are too big. Is there an application that can do this? (Windows much preferred; Linux only as a last resort) I do not want to dive into development or XSLT jobs. I am thinking that someone must have made a simple sorting tool like this already - I just can't find it using Google. Update: With help from this site, I created a small package that I want to share: XML-Sorter_v0.3.zip Update: Follow-up question here.

  Read the article

• DSL Connection drops

  - by user60024

  Ok, I just moved so I had to switch from Cable to DSL. I know very little about computers or internet connections and such, so I had AT&T come out to the new house to set up their highest speed. When they got here, they told me that I needed to downgrade to 3.5mbps because I was too far away. Well we did and everything was going great for two days until I started experiencing random disconnects which have been happening now for about 2 to 3 weeks. I am using a N300 Wireless Dual Band ADSL2+ Modem Router and my ethernet cable is hooked directly into my computer from it. I recently started to notice that it disconnects around 5:30 and 8:30, which may be because a lot of people are on their computers(?) and that it works perfectly fine, almost, all the time if I'm not playing a game. During this time, when I try to load up World of Warcraft the Internet light disappears and the DSL light begins blinking. (So maybe it's too much for the modem and it resets?) Other than that it is amazing, but I'd like to try and fix some of these problems. If you need more information, let me know on how to get it for you and what to do. Thanks for the help!

  Read the article

• Xen virtual host can reach some sites but not others

  - by Tun H S Lee

  Okay, this is killing me. Debian Squeeze, Xen 4.0, brand new install. No iptables rules whatsoever except for the ones added by the default xen bridge script. Dom0 can reach the entire world, no problems. DomU can receive packets from some hosts, but not from others. For instance, if I ping Host A, it works fine. If I ping Host B, the DomU reports 100% packet loss. The hosts are random, but consistent (even after reboots). I can see no pattern to why some work and others don't. In fact, in some cases, different virtual hosts on the same server (an other server at a different data center) are divided; some work and others do not. I can reboot (DomU or Dom0 too) and the same hosts will work or fail as before. If I tcpdump on the Host B while pinging from the DomU, everything looks fine. It sees the echo request coming in and says it's sending one back. However, if I tcpdump peth0 on the Dom0, it never sees the echo reply. Any ideas what could be happening? I'm tearing my hair out here.

  Read the article

• Why is my cron daemon is being killed every few minutes?

  - by user113215

  As of about a week ago, my cron daemon refuses to stay running. I'm using Debian 6 x64 on an OpenVZ virtual machine. Running something like pgrep cron shows that the daemon isn't running. I start the service with service cron start or /etc/init.d/cron start and it launches, but it disappears from the running process list after a few minutes (varying anywhere between 1 - 30 minutes before the process is killed again). Using strace -f service cron start, I can see that the process is being killed for some reason: nanosleep({60, 0}, <unfinished ...> +++ killed by SIGKILL +++ There's nothing relevant in /var/log/syslog, /var/log/messages, /var/log/auth.log, or /var/log/kern.log to explain why the the process is dying. The system has at least 800 MB of free memory, and cat /proc/loadavg returns 0.22 0.13 0.04 so resources shouldn't be the issue. With cron running, free -m reports: total used free shared buffers cached Mem: 1024 211 812 0 0 0 -/+ buffers/cache: 211 812 Swap: 0 0 0 I also tried removing and reinstalling the cron package using apt-get. Update: I initially thought the problem was a resource issues. I erased my entire VPS and started from a fresh Debian image. There is now nothing else running on the system, but even from a clean install my cron daemon is still being killed at random. What else should I check? How do I find out what's killing my crond?

  Read the article

• Configuring Vmware virtual machines to run under different IPs and PC specs

  - by Alex

  Right now I'm using a simple VmWare virtual machine with preinstalled Win 7. The IP is assigned automatically (it's the same as main OS IP). Is it possible to create several virtual machines that have different hardware specifications and different IP addresses? Here is what I mean regarding these issues: Specs: Certainly, you can easily change some specifications in the Settings menu (RAM size, HDD size), but what about advanced settings? For example: advanced settings for the Processor: is it AMD (2500+,4000+, etc.. ) or Intel (core 2, Pentium, etc..) Ram - is it Corsair 4 Gb 1333 Mhz or Kingston 2 x 2 Gb 866Mhz or something else? Hdd - Is it Seagate Barracuda 80 gb 5400 Rpm or is it Samsung 500Gb 7200 Rpm or some random SSD? Programs that work under a Virtual Machine shouldn't have a clue if that's a VmWare or not. IPs: Every program that's launched under main OS use the real IP: 93.56.xx.xx All programs that are launched under virtual machine A use IP 1: 74.78.xx.xx All programs that are launched under virtual machine B use IP 2: 84.159.xx.xx I believe that you have to use either VPN or Proxy to solve this problem. The Sum Up: The idea is to create 2-3 independent virtual machines with different hardware specifications and IP addresses. Programs that work under a certain Virtual Machine shouldn't have a clue if that's a VmWare or the real PC. Any ideas/tips or experience regarding configuration will be appreciated!

  Read the article

• Redmine does not return the web page

  - by m0skit0

  I migrated a Redmine installation from an Ubuntu machine to a Debian one (both 32-bits), and now for some reason, for some users it doesn't return the page but only a 200 OK message. Here is the flow (from Wireshark): GET /issues/142 HTTP/1.1 Host: debian:3000 User-Agent: Mozilla/5.0 (X11; Ubuntu; Linux i686; rv:17.0) Gecko/20100101 Firefox/17.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate Connection: keep-alive Cookie: _redmine_session=BAh7DCIQX2NzcmZfdG9rZW4iMStIM1RBNTlNelZVUXlUazgrR1pUNGUvNGdEbytUZzRyMVFSUnBvNGhlSDg9Ihd0aW1lbG9nX2luZGV4X3NvcnQiEnNwZW50X29uOmRlc2MiD3Nlc3Npb25faWQiJThiMDk0MzVhOTEzYTI0MzVjOGEzYTRmNDU0NzcwMTAwIgx1c2VyX2lkaQoiFmlzc3Vlc19pbmRleF9zb3J0IgxpZDpkZXNjIg1wZXJfcGFnZWlpIgpxdWVyeXsHOg9wcm9qZWN0X2lkaQc6B2lkaQo%3D--8588c221c0642a12f396239455fb702aec14c9c9; my_wiki_session=f70ae11e1c533c86f0e039d63cf3f69c; my_wikiUserID=1; my_wikiUserName=Yasin Cache-Control: max-age=0 HTTP/1.1 200 OK Connection: Keep-Alive Date: Wed, 12 Dec 2012 16:30:16 GMT Server: WEBrick/1.3.1 (Ruby/1.8.7/2010-08-16) Content-Length: 0 As you can see, I get nothing from the server. This is mostly random because this blank page happens sometimes for some users, and for other users it almost never returns the page... I'm absolutely lost here. Any idea about what can be the cause? Thanks in advance!

  Read the article

• Some Emails incoming to Outlook 2007 are blank, same emails work fine on webmail, iphone, etc

  - by Funran

  This is a pretty easy problem to describe. Basically users who have just been upgraded to Outlook 2007 (yeah I know 2010 is out), are not receiving SOME emails (from outside our domain, ie hotmail, yahoo). Receiving is not the correct word, these emails come in, along with their attachments, subjects, to/from line, etc. But the body is blank. If the same user goes into their webmail, iphone, blackberry instead, they can read the message fine. It's clear to me that something in Outlook 2007 is not generating the body correctly, so it just strips it. I just don't know WHY. Our mail server was recently upgraded to Exchange 2010, users on 2010 running outlook 2003 are working fine, it's just the random emails for users using 2007. I hope I made that clear enough, thank you for any future help guys. EDIT: I don't see rft, but i swear I've seen it before. Here is the view source on a recent email. <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"><html><head> <meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1"> <meta name="GENERATOR" content="MSHTML 8.00.6001.19120"> <DEFANGED_style_0 <="" style=""> </head> <body bgcolor="#ffffff"> <p><DEFANGED_DIV><font color="#0000ff" size="2" face="Calibri">MS,</font></p><DEFANGED_DIV> <p><DEFANGED_DIV><font color="#0000ff" size="2" face="Calibri">Could you tell me please what the legal descrip &amp; Topo Quad name is for this Monroe P.ID Site?</font></p><DEFANGED_DIV> <p><DEFANGED_DIV><em><font color="#0000ff" size="2" face="Calibri">Thanks, Henry Roye</font></em></p><DEFANGED_DIV></body></html>

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• SFTP access without hassle

  - by enobayram

  I'm trying to provide access to a local folder for someone over the internet. After googling around a bit, I've come to the conclusion that SFTP is the safest thing to expose through the firewall to the chaotic and evil world of the Internet. I'm planning to use the openssh-server to this end. Even though I trust that openssh will stop a random attacker, I'm not so sure about the security of my computer once someone is connected through ssh. In particular, even if I don't give that person's user account any privileges whatsoever, he might just be able to "su" to, say, "nobody". And since I was never worried about such things before, I might have given some moderate privileges to nobody at some point (not sudo rights surely!). I would of course value your comments about giving privileges to nobody in the first place, but that's not the point, really. My aim is to give SFTP access to someone in such a sandboxed state that I shouldn't need to worry about such things (at least not more so than I should have done before). Is this really possible? Am I speaking nonsense or worried in vain?

  Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >