logical domains - Page 164

Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

- by Shoshomiga

I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

Read the article

Can Remote Desktop Services be deployed and administered by PowerShell alone, without a Domain in WIndows Server 2012 and 2012 R2?

- by Warren P

Windows Server 2008 R2 allowed deployment of Terminal Server (Remote Desktop Services) without a domain, and without any insistence on domains. This was very useful, especially for standalone virtual or cloud deployments of a server that is managed remotely for a remote client who has no need or desire for any ActiveDirectory or Domain features. This has become steadily more and more difficult as Microsoft restricts its technologies further and further in each Windows release. With Windows Server 2012, configuring licensing for Remote Desktop Services, is more difficult when not on a domain, but possible still. With Windows Server 2012 R2 (at least in the preview) the barriers are now severe: The Add/Remove Roles and Features wizard in Windows Server 2012 R2 has a special RDS deployment mode that has a rule that says if you aren't on a domain you can't deploy. It tells you to create or join a domain first. This of course comes in direct conflict with the fact that an Active Directory domain controller should not be the same machine as a terminal server machine. So Microsoft's technology is not such much a Cloud Operating System as a Cluster of Unwanted Nodes, needed to support the one machine I actually WANT to deploy. This is gross, and so I am trying to find a workaround. However if you skip that wizard and just go check the checkboxes in the main Roles/Features wizard, you can deploy the features, but the UI is not there to configure them, and when you go back to the RDS configuration page on the roles wizard, you get a message saying you can not administer your Remote Desktop Services system when you are logged in as a Local-Computer Administrator, because although you have all admin priveleges you could have (in your workgroup based system), the RDS configuration UI will not accept those credentials and let you continue. My question in brief is, can I still somehow, obtain the following end result: I need to allow 10-20 users per system to have an RDS (TS) session. I do not need any of the fancy pants RDS options, unless Microsoft somehow depends on those features being present. I believe I need the "RDS Session Host" as this is the guts of "Terminal Server". Microsoft says it is "full Windows desktop for Remote Desktop Services client. I need to configure licensing so that the Grace Period does not expire leaving my RDS non functional, so this probably means I need a way to configure TS CALs. If all of the above could technically be done with the judicious use of the PowerShell, I am prepared to even consider developing all the PowerShell scripts I would need to do the above. I'm not asking someone to write that for me. What I'm asking is, does anyone know if there is a technical impediment to what I want to do above, other than the deliberate crippling of the 2012 R2 UI for Workgroup users? Would the underlying technologies all still work if I manipulate and control them from a PowerShell script? Obviously a 1 word Yes or No answer isn't that useful to anyone, so the question is really, yes or no, and why? In the case the answer is Yes, then how.

Read the article

MS DPM 2007: Testing the Recovery for a Production Domain

- by NewToDPM

Hi everybody! MS DPM 2007 is a new technology in my company, and so am I to the product. We have a classic Microsoft domain with two DCs, Exchange 2007 and a couple Web/MS SQL servers. I have deployed DPM one month ago on the domain, and after fixing the various issues I got with the replicas inconsistence and adapting the schedule and retention range to the server storage pool size, I can say the backup system is working correctly (no errors) as of today. However, there is one problem: we did not attempt to restore from the backups yet, which is a big no-no of course. I'm not sure about the way I should handle this, my main concern being Exchange and the System State of the DCs. From my understanding, DPM can only protect AND restore data on a server which is part of the same domain as the backup server. If I restore the System State (containing Active Directory) and the Exchange Storage Groups on a testing server, I am afraid it would completely disturb the domain functioning (for example, having two primary DCs on the domain). I am thinking about building a second DPM server on a testing separate domain which would mirror the replicas and then restore it on testing servers from this new domain. Is it the right way to handle the data recovery testing? How did you do on your domain when you first deployed DPM? I'd be grateful for any link/documentation or advice. Thank you in advance for your help! EDIT: Two options seem possible so far: i. Create another DC/Exchange server in the alternate location; ii. Create a separate domain in the alternate location and setup a trust between this domain and the production one. The option i is certainly the best but implies setting up a secondary Exchange server, with a dedicated public IP address so that if Exchange #1 dies, we can still send emails with Exchange #2. I don't know how complex this can be and would need to discuss it with my colleagues. The option ii would only fit the testing purposes. My only question regarding this is: if my production and DPM servers are part of domain A, and there is a trust between domains A and B, can I restore a domain A content to any domain B server?

Read the article

Enterprise IPv6 Migration - End of proxypac ? Start of Point-to-Point ? +10K users

- by Yohann

Let's start with a diagram : We can see a "typical" IPv4 company network with : An Internet acces through a proxy An "Others companys" access through an dedicated proxy A direct access to local resources All computers have a proxy.pac file that indicates which proxy to use or whether to connect directly. Computers have access to just a local DNS (no name resolution for google.com for example.) By the way ... The company does not respect the RFC1918 internally and uses public addresses! (historical reason). The use of internet proxy explicitly makes it possible to not to have problem. What if we would migrate to IPv6? Step 1 : IPv6 internet access Internet access in IPv6 is easy. Indeed, just connect the proxy in Internet IPv4 and IPv6. There is nothing to do in internal network : Step 2 : IPv6 AND IPv4 in internal network And why not full IPv6 network directly? Because there is always the old servers that are not compatible IPv6 .. Option 1 : Same architecture as in IPv4 with a proxy pac This is probably the easiest solution. But is this the best? I think the transition to IPv6 is an opportunity not to bother with this proxy pac! Option 2 : New architecture with transparent proxy, whithout proxypac, recursive DNS Oh yes! In this new architecture, we have: Explicit Internet Proxy becomes a Transparent Internet Proxy Local DNS becomes a Normal Recursive DNS + authorative for local domains No proxypac Explicit Company Proxy becomes a Transparent Company Proxy Routing Internal Routers reditect IP of appx.ext.example.com to Company Proxy. The default gateway is the Transparent Internet proxy. Questions What do you think of this architecture IPv6? This architecture will reveal the IP addresses of our internal network but it is protected by firewalls. Is this a real big problem? Should we keep the explicit use of a proxy? -How would you make for this migration scenario? -And you, how do you do in your company? Thanks! Feel free to edit my post to make it better.

Read the article

Single domain name potentially resolving to multiple servers

- by Jace

first time here at Server Fault, and I apologize in advance that this domain stuff is not really my strength. Any and all suggestions are much appreciated. I am completely lost and incredibly tired! I've inherited an incredibly convoluted system from my predecessor, and I'm trying to find a way to solve it - or I need to be told that it just isn't possible. I've got an old site on ServerA (some kind of Linux distribution), with the domain SomeDomain.com There is a new site sitting on ServerB (Ubuntu), with the intention of having SomeDomain.com to serve it in the future (it is replacing the old site) ServerA also has a web app that is currently in use by other departments within the company (accessible at SomeDomain.com/web-app/) The goal: To have SomeDomain.com and all extensions of this domain name (sub-domains, URL's etc.) serve the new site on ServerB. BUT, the URL SomeDomain.com/web-app/ must serve the Web App on ServerA. The Catch: The ServerA is a shared server with a hosting company with VERY limiting restrictions in place - I cannot adjust DNS settings (apart from Name servers - but cannot set A records or anything, I have full access to ServerB to do as I wish). Therefore the web-app MUST be served from SomeDomain.com/web-app/ and not from a sub-domain or anything. These limitations make migrating the web-app from Server A to Server B rather undesirable, AND this web-app will be replaced in the near future, so it isn't worth the effort right now. Therefore, ultimately I will want 1 domain name to resolve to Server B's IP address most of the time, but in the event that the URL is SomeDomain.com/web-app/, it should resolve to Server A's IP. Note: The domain names don't, technically, have to resolve to one IP or another - but ultimately the URL's must stay consistent Some things I have tried: I've looked into mod_rewrite and .htaccess to try and achieve this effect, but it doesn't look like it's going to work for me - but I may have done it wrong (On Server B, I just checked if the request URI was /web-app/ and tried to serve the /web-app/ folder on Server A) I do have the ability to modify the name servers on both servers I am not able to make a sub domain on Server A that points back to Server A (I assume because the hosting company's servers use the URL to determine what site the serve). I figured this could be good as I'd could set an A record on Server B to point to the web app on Server A - but alas, Server A requires SomeDomain.com. If there is any more information I can give, please let me know. I need a nudge in the right direction, ideas or a solution.

Read the article

PC will POST whenever feels likes it

- by kyrpas

I'm really sick of my PC and I'd love to throw it off the 5th floor but unfortunately I don't have this luxury right now. The issues started when I moved to a new house about 2 months ago. I didn't have this problem before. Case: Arctic Cooling Silentium T1 with embedded Fusion 550 Eco 80 PSU. M/B: ASRock A790GMH/128M Gfx: ATI Radeon HD 5770 Here's what's happening almost on a daily basis: I wake up in the morning, switch on the PC and all the fans start spinning. 9/10 the graphics fan stays on 100% and I know it won't post. If I'm lucky, ATI's fan stays on full power for a second, then goes back to normal and I get a normal post but that doesn't happen often. No, instead it's just drives me crazy. When I get no POST I'm trying a lot of different things and what bothers me the most is that they all work. But not always. No... That way I could find out what the hell is going on and we don't want that.. right? So, sometimes it manages to POST if I: remove the keyboard remove the power cable for a few minutes remove the graphics card remove the HDD cables do nothing, just turn it on and off a few times Sometimes it doesn't POST even if I do all of the above. And I end up removing all power cables from the M/B, and connecting all the stuff one by one. Sometimes it works, sometimes it doesn't and I just have to pray and wait. What the hell is that? I'm getting pissed of again just thinking about it. The only solution is to leave it on 24/7 but I don't want to do that. It should be able to turn on and off when I press the power button. I'm not asking much. I'm starting to think there's some weird electricity/power issue but I really don't understand what it is. There's no logical explanation about it. At least I can't find one. Any ideas?

Read the article

turn off disable the performance cache

- by jessie

OK I run a streaming website and my CMS is giving me an error when uploading videos "Failed To Find Flength File" ok so I did some research. The answer I got from the coder was below. I did do all that, but the only thing I could not do is turn off what he refers to as performance cache, talked about in the last sentence... I am on a Cent OS Assuming the script is set up properly, you are probably dealing with some kind of write-caching. Some servers perform write-caching which prevents writing out the flength file or the entire CGITemp file during the upload. The flength file or the CGITemp file do not actually hit the disk until the upload is complete, making it worthless for reporting on progress during the upload. This may be fixed using a .htaccess file assuming your host supports them. Here is a link to an excellent tutorial on using .htaccess files. I strongly recommend giving it a quick read before attempting to install your own .htaccess file. 1. A mod_security module for Apache. To fix it just create a file called .htaccess (that's a period followed by "htaccess") and put the following lines in that file. Upload the file into the directory where the Uber-Uploader CGI ".pl" scripts resides, or in some directory above it (like your server's DOCUMENT_ROOT, i.e. the top-level of your webspace). htaccess files must be uploaded as ASCII mode, not BINARY. You may need to CHMOD the htaccess file to 644 or (RW-R--R--). # Turn off mod_security filtering. SecFilterEngine Off # The below probably isn't needed, # but better safe than sorry. SecFilterScanPOST Off If the above method does not work, try putting the following lines into the file SetEnvIfNoCase Content-Type \ "^multipart/form-data;" "MODSEC_NOPOSTBUFFERING=Do not buffer file uploads" mod_gzip_on No 2. "Performance Cache" enabled on OS X SERVER. If you're running OS X Server and the progress bar isn't working, it could be because of "performance caching." Apparently if ANY of your hosted sites are using performance caching, then by default, all sites (domains) will attempt to. The fix then is to disable the performance cache on all hosted sites.

Read the article

If Nvidia Shield can stream a game via wifi, why can I not do the same via ethernet to any other PC?

- by Enigma

I think it absurd that a wireless game streaming solution is the *first to hit the market when a 1000mbps+ Ethernet connection would accomplish the same feat with roughly 6x the available bandwidth. I can only assume that there must be some reason behind this or a limitation preventing this, but what? 150mbps wifi is in no way superior to a 1000mbps LAN connection aside from well wireless mobility. Not only that but I have a secondary laptop and desktop which should by hardware comparison completely outperform anything the Tegra in the Nvidia Shield can do. Is this all just a marketing scheme to force people to buy the shield for the streaming benefit? Chief among these is that NVIDIA’s Shield handheld game console will be getting a microconsole-like mode, dubbed “Shield Console Mode”, that will allow the handheld to be converted into a more traditional TV-connected console. In console mode Shield can be controlled with a Bluetooth controller, and in accordance with the higher resolution of TVs will accept 1080p game streaming from a suitably equipped PC, versus 720p in handheld mode. With that said 1080p streaming will require additional bandwidth, and while 720p can be done over WiFi NVIDIA will be requiring a hardline GigE connection for 1080p streaming (note that Shield doesn’t have Ethernet, so this is presumably being done over USB). Streaming aside, in console mode Shield will also support its traditional local gaming/application functionality. - http://www.anandtech.com/show/7435/nvidia-consolidates-game-streaming-tech-under-gamestream-brand-announces-shield-console-mode ^ This is not acceptable for me for a number of reasons not to mention the ridiculousness of having a little screen+controller unit sitting there while using a secondary controller and screen instead. That kind of redundant absurdity exemplifies how wrong of a solution that is. They need a second product for this solution without the screen or controller for it to make sense... at which point your just buying a little computer that does what most other larger computers do better. All that is required, by my understanding, is the ability to decode H.264 video compression and transmit control/feedback so by any logical comparison, one (Nvidia especially) should have no difficulty in creating an application for PC's (win32/64 environment) that does the exact same thing their android app does. I have 2 video cards capable of streaming (encoding) H.264 so by right they must be capable of decoding it I would think. I haven't found anything stating plans to allow non-shield owners to do this. Can a third party create this software or does it hinge on some limitation that only Nvidia can overcome? (*) - perhaps this isn't the first but afaik it is the first complete package.

Read the article

HP Proliant G7 hardware RAID configuration automation with ribcl

- by karthik

I have been trying to automate hardware RAID configuration of HP proliant machines before OS installation (So I can not use hpacucli) ssh into iLO3 doesn't have option for RAID configuration I use ribcl but there is no command for RAID config, however I see this under the command GET_EMBEDDED_HEALTH. <STORAGE> <CONTROLLER> <LABEL VALUE="Controller on System Board"/> <STATUS VALUE="OK"/> <CONTROLLER_STATUS VALUE="OK"/> <SERIAL_NUMBER VALUE="50014380215F0070"/> <MODEL VALUE="HP Smart Array P420i Controller"/> <FW_VERSION VALUE="3.41"/> <DRIVE_ENCLOSURE> <LABEL VALUE="Port 1I Box 1"/> <STATUS VALUE="OK"/> <DRIVE_BAY VALUE="04"/> </DRIVE_ENCLOSURE> <DRIVE_ENCLOSURE> <LABEL VALUE="Port 2I Box 0"/> <STATUS VALUE="OK"/> <DRIVE_BAY VALUE="01"/> </DRIVE_ENCLOSURE> <LOGICAL_DRIVE> <LABEL VALUE="01"/> <STATUS VALUE="OK"/> <CAPACITY VALUE="68 GB"/> <FAULT_TOLERANCE VALUE="RAID 0"/> <PHYSICAL_DRIVE> <LABEL VALUE="Port 1I Box 1 Bay 3"/> <STATUS VALUE="OK"/> <SERIAL_NUMBER VALUE="6TA0N3SZ0000B231CYDT"/> <MODEL VALUE="EH0072FAWJA"/> <CAPACITY VALUE="68 GB"/> <LOCATION VALUE="Port 1I Box 1 Bay 3"/> <FW_VERSION VALUE="HPDH"/> <DRIVE_CONFIGURATION VALUE="Configured"/> </PHYSICAL_DRIVE> </LOGICAL_DRIVE> </CONTROLLER> </STORAGE> My question is, is there a way I modify/create this xml piece (say I have 2 Logical drive with one spare) and reboot the server it takes effect ? If this approach is not correct are there any other ways to automate hardware raid config ?

Read the article

How to configure apache's mod_proxy_html to work as an ajax proxy?

- by dcerecedo

I'm trying to build a web site that let's you view and manipulate data from any page in any other website. To do that, I have to bypass 'Allow Origin' problems: i'm loading the other domain's content in an iframe and i have to manipulate its content with javascript downloaded from my domain. My first attempt was to write a simple proxy myself, requesting the other domains page through a server proxy coded in Java that not only serves the content but rebuilds links (src's and href's) in the content so that the content referenced by these links alse get downloaded through my handmade proxy. The result is not bad but has problems with url's in css and scripts. It's then that i realized that mod_proxy_html is supposed to do exactly all this job. The problem is that i cannot figure out how to make it work as expected. Let's suppose my server runs in my-domain.com and to proxy and transform content from another domain i'd make a request like this: my-domain.com/proxy?url=http://another-domain.com/some/content I'd want mod_proxy_html to serve the content and rewrite following URLs in http://another-domain.com/some/content in the following ways: Absolute URLs not from another-domain.com: no rewritting Relative from root urls:/other/content - /proxy?url=http://another-domain.com/other/content Relative urls: other/content - /proxy?url=http://another-domain.com/some/content/other/content Relative to parent urls: ../other/content - /proxy?url=http://another-domain.com/some/other/content The url should be specified at runtime, not configuration time. Can this be achieved with mod_proxy_html? Could anyone provide a simple working configuration to start with? EDIT 1-First approach The following site config will work fine with sites that use absolute url's everywhere like http://www.huffingtonpost.es/. Youc could try on this config on localhost: http://localhost/asset/http://www.huffingtonpost.es/ <VirtualHost *:80> ServerName localhost LogLevel debug ProxyRequests off RewriteEngine On RewriteRule ^/asset/(.*) $1 [P] ProxyHTMLURLMap $1 /asset/ <Location /asset/> ProxyPassReverse / ProxyHTMLURLMap / /asset/ </Location> </VirtualHost> But as explained in the documentation, if I hit a site using relative url's, I'd like to have these rewritten on the html via mod_proxy_html. So I shoud change the Location block as follows: <Location /asset/> ProxyPassReverse / #Depending on your system use one line or the other #Ubuntu: #SetOutputFilter proxy-html #any other system: ProxyHTMLEnable On ProxyHTMLURLMap / /asset/ </Location> ...which doesn't seem to work. Comments, hints and ideas welcome!

Read the article

USB hard drive not recognized

- by user318772

Until recently I was using the portable USB hard drive in my win 7 laptop and ubuntu laptop. Suddenly now none of the laptops recognize it. This is the message i get by doing lsusb... Bus 001 Device 004: ID 1058:1010 Western Digital Technologies, Inc. Elements External HDD Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 003 Device 002: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub fdisk doesn't show the external hard drive Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004a743 Device Boot Start End Blocks Id System /dev/sda1 * 2048 152111103 76054528 83 Linux /dev/sda2 152113150 156301311 2094081 5 Extended /dev/sda5 152113152 156301311 2094080 82 Linux swap / Solaris when i do testdisk TestDisk 6.14, Data Recovery Utility, July 2013 Christophe GRENIER <[email protected]> http://www.cgsecurity.org TestDisk is free software, and comes with ABSOLUTELY NO WARRANTY. Select a media (use Arrow keys, then press Enter): >Disk /dev/sda - 80 GB / 74 GiB - ST980825AS Disk /dev/sdb - 2199 GB / 2048 GiB testdisk-> Intel->analyse I get partition error Disk /dev/sdb - 2199 GB / 2048 GiB - CHS 2097152 64 32 Current partition structure: Partition Start End Size in sectors Partition: Read error Here is the output of dmesg [11948.549171] Add. Sense: Invalid command operation code [11948.549177] sd 2:0:0:0: [sdb] CDB: [11948.549181] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.550489] sd 2:0:0:0: [sdb] Invalid command failure [11948.550495] sd 2:0:0:0: [sdb] [11948.550499] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.550505] sd 2:0:0:0: [sdb] [11948.550508] Sense Key : Illegal Request [current] [11948.550514] Info fld=0x0 [11948.550519] sd 2:0:0:0: [sdb] [11948.550525] Add. Sense: Invalid command operation code [11948.550531] sd 2:0:0:0: [sdb] CDB: [11948.550534] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.551870] sd 2:0:0:0: [sdb] Invalid command failure [11948.551876] sd 2:0:0:0: [sdb] [11948.551880] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.551885] sd 2:0:0:0: [sdb] [11948.551888] Sense Key : Illegal Request [current] [11948.551895] Info fld=0x0 [11948.551900] sd 2:0:0:0: [sdb] [11948.551905] Add. Sense: Invalid command operation code [11948.551911] sd 2:0:0:0: [sdb] CDB: [11948.551914] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 If possible i want to retrive at least some data from this hard drive. If thats not possible I would like to format it and use it. Any help will be greatly appreciated Thanks

Read the article

Network unreachable on Ubuntu guest after trying to set up a host only network on Virtualbox

- by gkb0986

I have a Mac OS X host and a bunch of guests including Ubuntu and Arch Linux. I was trying to set up a host-only network at eth1 to let me ssh into the system. But now eth0 isn't working properly either. Ubuntu can no longer connect to remote hosts or browse the internet. It tells me that the network is unreachable. What's gone wrong here? I've included some diagnostics below. $ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10968 errors:0 dropped:0 overruns:0 frame:0 TX packets:10968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:897264 (897.2 KB) TX bytes:897264 (897.2 KB) Other diagnostic commands and the output: $sudo lspci -n 00:00.0 0600: 8086:1237 (rev 02) 00:01.0 0601: 8086:7000 00:01.1 0101: 8086:7111 (rev 01) 00:02.0 0300: 80ee:beef 00:03.0 0200: 8086:100e (rev 02) 00:04.0 0880: 80ee:cafe 00:05.0 0401: 8086:2415 (rev 01) 00:06.0 0C03: 106B:003F 00:07.0 0680: 8086:7113 (REV 08) 00:0D.0 0106: 8086:2829 (REV 02) $sudo lshw -c network *-network DISABLED description: Ethernet interface product: 82540EM Gigabit Ethernet Controller vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 logical name: eth0 version: 02 serial: 08:00:27:7d:22:df size: 1Gbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k8-NAPI duplex=full firmware=N/A latency=64 link=no mingnt=255 multicast=yes port=twisted pair speed=1Gbit/s resources: irq:19 memory:f0000000-f001ffff ioport:d010(size=8) $lsmod Module Size Used by nls_utf8 12557 1 isofs 40257 1 vboxsf 43743 2 vesafb 13844 1 snd_intel8x0 38570 2 snd_ac97_codec 134869 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97275 2 snd_intel8x0,snd_ac97_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi rfcomm 47604 0 snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event bnep 18281 2 bluetooth 180113 10 rfcomm,bnep ppdev 17113 0 psmouse 97519 0 snd_timer 29990 2 snd_pcm,snd_seq joydev 17693 0 snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq vboxvideo 12622 1 serio_raw 13211 0 snd 79041 11 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd vboxguest 235498 7 vboxsf parport_pc 32866 0 drm 241971 2 vboxvideo i2c_piix4 13301 0 snd_page_alloc 18529 2 snd_intel8x0,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usbhid 47238 0 hid 99636 1 usbhid e1000 108589 0

Read the article

Mac OSX 10.8 Server DNS Domain Routing

- by Oldek

I just cant seem to figure out the logic in how to configure my Mac Server. So I have set up an DNS, which will take the domain and all subdomains and point towards an IP. File: db.mydomain.com (in /var/named/) mydomain.com. 10800 IN SOA mydomain.com. admin.mydomain.com. ( 2012110903 ; serial 3600 ; refresh (1 hour) 900 ; retry (15 minutes) 1209600 ; expire (2 weeks) 86400 ; minimum (1 day) ) 10800 IN NS mydomain.com. 10800 IN A 10.0.1.2 www.mydomain.com. 10800 IN A 10.0.1.2 So I want all of these requests to be requested to the 10.0.1.2 server, as I run 2 servers in my cluster. This one has always handled the requests, and now I want to add a server in between. So the server in between will get all the signals from my router which NAT the trafic coming from outside. So after setting this up and trying to point my port 80 towards my new server which will be the middle point, it doesn't work. Is it even possible to do it this way? First server: Mac Second server: Linux So what I try to achieve once more: 1. User goes to mydomain.com or www.mydomain.com 2. User request gets handled by my first server 3. First server refers to a local server, which is only available locally (it is configured to allow requests on port 80 and handle them) 4. Second server receives signal 5. Second server returns a request (either directly send to user or send through first server, whichever is most secure and configurable) I also want to be able to set up domains that lead to other servers in the future, and some that are only available within the VPN. (If that changes anything) I hope some kind soul could help me with this, it is really cumbersome for my mind to get the logic here. Do I have to configure my other server in any way? /Marcus

Read the article

Can't recover hard drive

- by BreezyChick89

My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

Read the article

unable to connect site to different port

- by JohnMerlino

I have a domain was registered at godaddy named http://mysite.com/. I logged into godaddy and I went to All Products Domains Domain Management. I clicked on the appropriate domain and it took me to the Domain Details page. I clicked Launch under DNS Manager and it took me to the Zone File Editor. I noticed that notify.mysite.com was pointing to an IP address pointing to a dead server, so I switched it to an operating server. Then I pinged the domain to see where it was pointing to and it was correctly pointing to the working server. So I copied the default configuration under sites-available: sudo cp default notify.mysite.com. And then I made some edits to it to have it point to a different document root to serve files at a different port: Listen 1740 Listen 64.135.xx.xxx:1740 #I also tried this as well: NameVirtualHost 64.135.xx.xxx:1740 <VirtualHost 64.135.xx.xxx:1740> ServerAdmin [email protected] ServerName notify.mysite.com DocumentRoot /var/www/test/public <Directory /var/www/test/public> Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> Then I enabled the virtual host. Then I went to the document root and added an index.html file with some text in it. Then I restarted apache. The restart gave no errors. Then I type the correct domain in URL: http://notify.mysite.com:1740/ and I get: Oops! Google Chrome could not connect to notify.mysite.com:1740 Somehow it took out all my other sites. Now even the ones that were responding on port 80 are no longe responding, even though I did not touch the virtual hosts for them. I get this message now: Oops! Google Chrome could not connect to mysite.com However, ping responds: ping mysite.com PING mysite.com (64.135.12.134): 56 data bytes 64 bytes from 64.135.12.134: icmp_seq=0 ttl=49 time=20.839 ms 64 bytes from 64.135.12.134: icmp_seq=1 ttl=49 time=20.489 ms The result of telnet: $ telnet guarddoggps.com 80 Trying 64.135.12.134... telnet: connect to address 64.135.12.134: Connection refused telnet: Unable to connect to remote host

Read the article

web.xml not reloading in tomcat even after stop/start

- by ajay

This is in relation to:- http://stackoverflow.com/questions/2576514/basic-tomcat-servlet-error I changed my web.xml file, did ant compile , all, /etc/init.d/tomcat stop , start Even then my web.xml file in tomcat deployment is still unchanged. This is build.properties file:- app.name=hello catalina.home=/usr/local/tomcat manager.username=admin manager.password=admin This is my build.xml file. Is there something wrong with this:-    <project name="My Project" default="compile" basedir=".">   <property file="build.properties"/> <property file="${user.home}/build.properties"/>   <property name="app.name" value="myapp"/> <property name="app.path" value="/${app.name}"/> <property name="app.version" value="0.1-dev"/> <property name="build.home" value="${basedir}/build"/> <property name="catalina.home" value="../../../.."/>  <property name="dist.home" value="${basedir}/dist"/> <property name="docs.home" value="${basedir}/docs"/> <property name="manager.url" value="http://localhost:8080/manager"/> <property name="src.home" value="${basedir}/src"/> <property name="web.home" value="${basedir}/web"/>       <path id="compile.classpath">     <fileset dir="${catalina.home}/bin"> <include name="*.jar"/> </fileset> <pathelement location="${catalina.home}/lib"/> <fileset dir="${catalina.home}/lib"> <include name="*.jar"/> </fileset> </path>   <taskdef resource="org/apache/catalina/ant/catalina.tasks" classpathref="compile.classpath"/>   <property name="compile.debug" value="true"/> <property name="compile.deprecation" value="false"/> <property name="compile.optimize" value="true"/>   <target name="all" depends="clean,compile" description="Clean build and dist directories, then compile"/>   <target name="clean" description="Delete old build and dist directories"> <delete dir="${build.home}"/> <delete dir="${dist.home}"/> </target>   <target name="compile" depends="prepare" description="Compile Java sources">  <mkdir dir="${build.home}/WEB-INF/classes"/> <javac srcdir="${src.home}" destdir="${build.home}/WEB-INF/classes" debug="${compile.debug}" deprecation="${compile.deprecation}" optimize="${compile.optimize}"> <classpath refid="compile.classpath"/> </javac>  <copy todir="${build.home}/WEB-INF/classes"> <fileset dir="${src.home}" excludes="**/*.java"/> </copy> </target>   <target name="dist" depends="compile,javadoc" description="Create binary distribution">  <mkdir dir="${dist.home}/docs"/> <copy todir="${dist.home}/docs"> <fileset dir="${docs.home}"/> </copy>  <jar jarfile="${dist.home}/${app.name}-${app.version}.war" basedir="${build.home}"/>  </target>   <target name="install" depends="compile" description="Install application to servlet container"> <deploy url="${manager.url}" username="${manager.username}" password="${manager.password}" path="${app.path}" localWar="file://${build.home}"/> </target>   <target name="javadoc" depends="compile" description="Create Javadoc API documentation"> <mkdir dir="${dist.home}/docs/api"/> <javadoc sourcepath="${src.home}" destdir="${dist.home}/docs/api" packagenames="*"> <classpath refid="compile.classpath"/> </javadoc> </target>   <target name="list" description="List installed applications on servlet container"> <list url="${manager.url}" username="${manager.username}" password="${manager.password}"/> </target>   <target name="prepare">  <mkdir dir="${build.home}"/> <mkdir dir="${build.home}/WEB-INF"/> <mkdir dir="${build.home}/WEB-INF/classes"/>  <copy todir="${build.home}"> <fileset dir="${web.home}"/> </copy>   <mkdir dir="${build.home}/WEB-INF/lib"/>    </target>   <target name="reload" depends="compile" description="Reload application on servlet container"> <reload url="${manager.url}" username="${manager.username}" password="${manager.password}" path="${app.path}"/> </target>   <target name="remove" description="Remove application on servlet container"> <undeploy url="${manager.url}" username="${manager.username}" password="${manager.password}" path="${app.path}"/> </target> </project>

Read the article

Simple Self Join Query Bad Performance

- by user1514042

Could anyone advice on how do I improve the performance of the following query. Note, the problem seems to be caused by where clause. Data (table contains a huge set of rows - 500K+, the set of parameters it's called with assums the return of 2-5K records per query, which takes 8-10 minutes currently): USE [SomeDb] GO SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO CREATE TABLE [dbo].[Data]( [x] [money] NOT NULL, [y] [money] NOT NULL, CONSTRAINT [PK_Data] PRIMARY KEY CLUSTERED ( [x] ASC )WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = ON) ON [PRIMARY] ) ON [PRIMARY] GO The Query select top 10000 s.x as sx, e.x as ex, s.y as sy, e.y as ey, e.y - s.y as y_delta, e.x - s.x as x_delta from Data s inner join Data e on e.x > s.x and e.x - s.x between xFrom and xTo --where e.y - s.y > @yDelta -- when uncommented causes a huge delay Update 1 - Execution Plan <?xml version="1.0" encoding="utf-16"?> <ShowPlanXML xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Version="1.2" Build="11.0.2100.60" xmlns="http://schemas.microsoft.com/sqlserver/2004/07/showplan"> <BatchSequence> <Batch> <Statements> <StmtSimple StatementCompId="1" StatementEstRows="100" StatementId="1" StatementOptmLevel="FULL" StatementOptmEarlyAbortReason="GoodEnoughPlanFound" StatementSubTreeCost="0.0263655" StatementText="select top 100
s.x as sx,
e.x as ex,
s.y as sy,
e.y as ey,
e.y - s.y as y_delta,
e.x - s.x as x_delta
from Data s 
 inner join Data e
 on e.x > s.x and e.x - s.x between 100 and 105
where e.y - s.y > 0.01
" StatementType="SELECT" QueryHash="0xAAAC02AC2D78CB56" QueryPlanHash="0x747994153CB2D637" RetrievedFromCache="true"> <StatementSetOptions ANSI_NULLS="true" ANSI_PADDING="true" ANSI_WARNINGS="true" ARITHABORT="true" CONCAT_NULL_YIELDS_NULL="true" NUMERIC_ROUNDABORT="false" QUOTED_IDENTIFIER="true" /> <QueryPlan DegreeOfParallelism="0" NonParallelPlanReason="NoParallelPlansInDesktopOrExpressEdition" CachedPlanSize="24" CompileTime="13" CompileCPU="13" CompileMemory="424"> <MemoryGrantInfo SerialRequiredMemory="0" SerialDesiredMemory="0" /> <OptimizerHardwareDependentProperties EstimatedAvailableMemoryGrant="52199" EstimatedPagesCached="14561" EstimatedAvailableDegreeOfParallelism="4" /> <RelOp AvgRowSize="55" EstimateCPU="1E-05" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Compute Scalar" NodeId="0" Parallel="false" PhysicalOp="Compute Scalar" EstimatedTotalSubtreeCost="0.0263655"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> <ColumnReference Column="Expr1004" /> <ColumnReference Column="Expr1005" /> </OutputList> <ComputeScalar> <DefinedValues> <DefinedValue> <ColumnReference Column="Expr1004" /> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[y] as [e].[y]-[SomeDb].[dbo].[Data].[y] as [s].[y]"> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> </DefinedValue> <DefinedValue> <ColumnReference Column="Expr1005" /> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x]"> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> </DefinedValue> </DefinedValues> <RelOp AvgRowSize="39" EstimateCPU="1E-05" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Top" NodeId="1" Parallel="false" PhysicalOp="Top" EstimatedTotalSubtreeCost="0.0263555"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="1" ActualExecutions="1" /> </RunTimeInformation> <Top RowCount="false" IsPercent="false" WithTies="false"> <TopExpression> <ScalarOperator ScalarString="(100)"> <Const ConstValue="(100)" /> </ScalarOperator> </TopExpression> <RelOp AvgRowSize="39" EstimateCPU="151828" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Inner Join" NodeId="2" Parallel="false" PhysicalOp="Nested Loops" EstimatedTotalSubtreeCost="0.0263455"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="0" ActualExecutions="1" /> </RunTimeInformation> <NestedLoops Optimized="false"> <OuterReferences> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OuterReferences> <RelOp AvgRowSize="23" EstimateCPU="1.80448" EstimateIO="3.76461" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="1" LogicalOp="Clustered Index Scan" NodeId="3" Parallel="false" PhysicalOp="Clustered Index Scan" EstimatedTotalSubtreeCost="0.0032831" TableCardinality="1640290"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="15225" ActualEndOfScans="0" ActualExecutions="1" /> </RunTimeInformation> <IndexScan Ordered="false" ForcedIndex="false" ForceScan="false" NoExpandHint="false"> <DefinedValues> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </DefinedValue> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </DefinedValue> </DefinedValues> <Object Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Index="[PK_Data]" Alias="[e]" IndexKind="Clustered" /> </IndexScan> </RelOp> <RelOp AvgRowSize="23" EstimateCPU="0.902317" EstimateIO="1.88387" EstimateRebinds="1" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Clustered Index Seek" NodeId="4" Parallel="false" PhysicalOp="Clustered Index Seek" EstimatedTotalSubtreeCost="0.0263655" TableCardinality="1640290"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="15224" ActualExecutions="15225" /> </RunTimeInformation> <IndexScan Ordered="true" ScanDirection="FORWARD" ForcedIndex="false" ForceSeek="false" ForceScan="false" NoExpandHint="false" Storage="RowStore"> <DefinedValues> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </DefinedValue> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </DefinedValue> </DefinedValues> <Object Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Index="[PK_Data]" Alias="[s]" IndexKind="Clustered" /> <SeekPredicates> <SeekPredicateNew> <SeekKeys> <EndRange ScanType="LT"> <RangeColumns> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </RangeColumns> <RangeExpressions> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[x] as [e].[x]"> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> </RangeExpressions> </EndRange> </SeekKeys> </SeekPredicateNew> </SeekPredicates> <Predicate> <ScalarOperator ScalarString="([SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x])>=($100.0000) AND ([SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x])<=($105.0000) AND ([SomeDb].[dbo].[Data].[y] as [e].[y]-[SomeDb].[dbo].[Data].[y] as [s].[y])>(0.01)"> <Logical Operation="AND"> <ScalarOperator> <Compare CompareOp="GE"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="($100.0000)" /> </ScalarOperator> </Compare> </ScalarOperator> <ScalarOperator> <Compare CompareOp="LE"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="($105.0000)" /> </ScalarOperator> </Compare> </ScalarOperator> <ScalarOperator> <Compare CompareOp="GT"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="(0.01)" /> </ScalarOperator> </Compare> </ScalarOperator> </Logical> </ScalarOperator> </Predicate> </IndexScan> </RelOp> </NestedLoops> </RelOp> </Top> </RelOp> </ComputeScalar> </RelOp> </QueryPlan> </StmtSimple> </Statements> </Batch> </BatchSequence> </ShowPlanXML>

Read the article

SharePoint 2010 – Central Admin tooling to create host header site collections

- by eJugnoo

Just like SharePoint 2007, you can create host-header based site collections in SharePoint 2010 as well. It means, that you do not necessarily need to create a site-collection under a managed path like /sites/, you can create multiple root-level site collections on same web-application/port by using host-header site collections. All you need to do is point your domain or sub-domain to your web-application and create a matching site-collection that you want. But, just like in 2007, it is something that you do by using STSADM, and is not available on Central Admin UI in 2010 as well. Yeah, though you can now also use PowerShell to create one: C:\PS>$w = Get-SPWebApplication http://sitename C:\PS>New-SPSite http://www.contoso.com -OwnerAlias "DOMAIN\jdoe" -HostHeaderWebApplication $w -Title "Contoso" -Template "STS#0" This example creates a host header site collection. Because the template is provided, the root Web of this site collection will be created. .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } I’ve been playing with WCM in SharePoint 2010 more and more, and for that I preferred creating hosts file entries for desired domains and create site-collections by those headers – in my dev environment. I used PowerShell initially, but then got interested to build my own UI on Central Admin instead. Developed with Visual Studio 2010 So I used new Visual Studio 2010 tooling to create an empty SharePoint 2010 project. Added an application page (there is no option to add _Admin page item in VS 2010 RC), that got created in Layouts “mapped” folder. Created a new Admin mapped folder for 14-“hive”, and moved my new page there instead. Yes, I didn’t change the base class for page, its just that it runs under _admin, but it is indeed a LayoutsPageBase inherited page. To introduce a action-link in Central Admin console, I created following element: 1: <Elements xmlns="http://schemas.microsoft.com/sharepoint/"> 2: <CustomAction 3: Id="CreateSiteByHeader" 4: Location="Microsoft.SharePoint.Administration.Applications" 5: Title="Create site collections by host header" 6: GroupId="SiteCollections" 7: Sequence="15" 8: RequiredAdmin="Delegated" 9: Description="Create a new top-level web site, by host header" > 10: <UrlAction Url="/_admin/OfficeToolbox/CreateSiteByHeader.aspx" /> 11: </CustomAction> 12: </Elements> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Used Reflector to understand any special code behind createpage.aspx, and created a new for our purpose – CreateSiteByHeader.aspx. From there I quickly created a similar code behind, without all the fancy of Farm Config Wizard handling and dealt with alternate implementations of sealed classes! Goal was to create a professional looking and OOB-type experience. I also added Regex validation to ensure user types a valid domain name as header value. Below is the result… Release @ Codeplex I’ve released to WSP on OfficeToolbox @ Codeplex, and you can download from here. Hope you find it useful… -- Sharad

Read the article

How to use jQuery Date Range Picker plugin in asp.net

- by alaa9jo

I stepped by this page: http://www.filamentgroup.com/lab/date_range_picker_using_jquery_ui_16_and_jquery_ui_css_framework/ and let me tell you,this is one of the best and coolest daterangepicker in the web in my opinion,they did a great job with extending the original jQuery UI DatePicker.Of course I made enhancements to the original plugin (fixed few bugs) and added a new option (Clear) to clear the textbox. In this article I well use that updated plugin and show you how to use it in asp.net..you will definitely like it. So,What do I need? 1- jQuery library : you can use 1.3.2 or 1.4.2 which is the latest version so far,in my article I will use the latest version. 2- jQuery UI library (1.8): As I mentioned earlier,daterangepicker plugin is based on the original jQuery UI DatePicker so that library should be included into your page. 3- jQuery DateRangePicker plugin : you can go to the author page or use the modified one (it's included in the attachment),in this article I will use the modified one. 4- Visual Studio 2005 or later : very funny :D,in my article I will use VS 2008. Note: in the attachment,I included all CSS and JS files so don't worry. How to use it? First thing,you will have to include all of the CSS and JS files into your page like this: <script src="Scripts/jquery-1.4.2.min.js" type="text/javascript"></script> <script src="Scripts/jquery-ui-1.8.custom.min.js" type="text/javascript"></script> <script src="Scripts/daterangepicker.jQuery.js" type="text/javascript"></script> <link href="CSS/redmond/jquery-ui-1.8.custom.css" rel="stylesheet" type="text/css" /> <link href="CSS/ui.daterangepicker.css" rel="stylesheet" type="text/css" /> <style type="text/css"> .ui-daterangepicker { font-size: 10px; } </style> Then add this html: <asp:TextBox ID="TextBox1" runat="server" Font-Size="10px"></asp:TextBox><asp:Button ID="SubmitButton" runat="server" Text="Submit" OnClick="SubmitButton_Click" /> <span>First Date:</span><asp:Label ID="FirstDate" runat="server"></asp:Label> <span>Second Date:</span><asp:Label ID="SecondDate" runat="server"></asp:Label> As you can see,it includes TextBox1 which we are going to attach the daterangepicker to it,2 labels to show you later on by code on how to read the date from the textbox and set it to the labels Now we have to attach the daterangepicker to the textbox by using jQuery (Note:visit the author's website for more info on daterangerpicker's options and how to use them): <script type="text/javascript"> $(function() { $("#<%= TextBox1.ClientID %>").attr("readonly", "readonly"); $("#<%= TextBox1.ClientID %>").attr("unselectable", "on"); $("#<%= TextBox1.ClientID %>").daterangepicker({ presetRanges: [], arrows: true, dateFormat: 'd M, yy', clearValue: '', datepickerOptions: { changeMonth: true, changeYear: true} }); }); </script> Finally,add this C# code: protected void SubmitButton_Click(object sender, EventArgs e) { if (TextBox1.Text.Trim().Length == 0) { return; } string selectedDate = TextBox1.Text; if (selectedDate.Contains("-")) { DateTime startDate; DateTime endDate; string[] splittedDates = selectedDate.Split("-".ToCharArray(), StringSplitOptions.RemoveEmptyEntries); if (splittedDates.Count() == 2 && DateTime.TryParse(splittedDates[0], out startDate) && DateTime.TryParse(splittedDates[1], out endDate)) { FirstDate.Text = startDate.ToShortDateString(); SecondDate.Text = endDate.ToShortDateString(); } else { //maybe the client has modified/altered the input i.e. hacking tools } } else { DateTime selectedDateObj; if (DateTime.TryParse(selectedDate, out selectedDateObj)) { FirstDate.Text = selectedDateObj.ToShortDateString(); SecondDate.Text = string.Empty; } else { //maybe the client has modified/altered the input i.e. hacking tools } } } This is the way on how to read from the textbox,That's it!. FAQ: 1-Why did you add this code?: <style type="text/css"> .ui-daterangepicker { font-size: 10px; } </style> A:For two reasons: 1)To show the Daterangepicker in a smaller size because it's original size is huge 2)To show you how to control the size of it. 2- Can I change the theme? A: yes you can,you will notice that I'm using Redmond theme which you will find it in jQuery UI website,visit their website and download a different theme,you may also have to make modifications to the css of daterangepicker,it's all yours. 3- Why did you add a font size to the textbox? A: To make the design look better,try to remove it and see by your self. 4- Can I register the script at codebehind? A: yes you can 5- I see you have added these two lines,what they do? $("#<%= TextBox1.ClientID %>").attr("readonly", "readonly"); $("#<%= TextBox1.ClientID %>").attr("unselectable", "on"); A:The first line will make the textbox not editable by the user,the second will block the blinking typing cursor from appearing if the user clicked on the textbox,you will notice that both lines are necessary to be used together,you can't just use one of them...for logical reasons of course. Finally,I hope everyone liked the article and as always,your feedbacks are always welcomed and if anyone have any suggestions or made any modifications that might be useful for anyone else then please post it at at the author's website and post a reference to your post here.

Read the article

Adobe Photoshop Vs Lightroom Vs Aperture

- by Aditi

Adobe Photoshop is the standard choice for photographers, graphic artists and Web designers. Adobe Photoshop Lightroom & Apple’s Aperture are also in the same league but the usage is vastly different. Although Photoshop is most popular & widely used by photographers, but in many ways it’s less relevant to photographers than ever before. As Lightroom & Aperture is aimed squarely at photographers for photo-processing. With this write up we are going to help you choose what is right for you and why. Adobe Photoshop Adobe Photoshop is the most liked tool for the detailed photo editing & designing work. Photoshop provides great features for rollover and Image slicing. Adobe Photoshop includes comprehensive optimization features for producing the highest quality Web graphics with the smallest possible file sizes. You can also create startling animations with it. Designers & Editors know how important precise masking is, PhotoShop lets you do that with various detailing tools. Art history brush, contact sheets, and history palette are some of the smart features, which add to its viability. Download Whether you’re producing printed pages or moving images, you can work more efficiently and produce better results because of its smooth integration across other adobe applications. Buy supporting layer effects, it allows you to quickly add drop shadows, inner and outer glows, bevels, and embossing to layers. It also provides Seamless Web Graphics Workflow. Photoshop is hands-down the BEST for editing. Photoshop Cons: • Slower, less precise editing features in Bridge • Processing lots of images requires actions and can be slower than exporting images from Lightroom • Much slower with editing and processing a large number of images Aperture Apple Aperture is aimed at the professional photographer who shoots predominantly raw files. It helps them to manage their workflow and perform their initial Raw conversion in a better way. Aperture provides adjustment tools such as Histogram to modify color and white balance, but most of the editing of photos is left for Photoshop. It gives users the option of seeing their photographs laid out like slides or negatives on a light table. It boasts of – stars, color-coding and easy techniques for filtering and picking images. Aperture has moved forward few steps than Photoshop, but most of the editing work has been left for Photoshop as it features seamless Photoshop integration. Aperture Pros: Aperture is a step up from the iPhoto software that comes with every Mac, and fairly easy to learn. Adjustments are made in a logical order from top to bottom of the menu. You can store the images in a library or any folder you choose. Aperture also works really well with direct Canon files. It is just $79 if you buy it through Apple’s App Store Moving forward, it will run on the iPad, and possibly the iPhone – Adobe products like Lightroom and Photoshop may never offer these options It is much nicer and simpler user interface. Lightroom Lightroom does a smashing job of basic fixing and editing. It is more advanced tool for photographers. They can use it to have a startling photography effect. Light room has many advanced features, which makes it one of the best tools for photographers and far ahead of the other two. They are Nondestructive editing. Nothing is actually changed in an image until the photo is exported. Better controls over organizing your photos. Lightroom helps to gather a group of photos to use in a slideshow. Lightroom has larger Compare and Survey views of images. Quickly customizable interface. Simple keystrokes allow you to perform different All Lightroom controls are kept available in panels right next to the photos. Always-available History palette, it doesn’t go when you close lightroom. You gain more colors to work with compared to Photoshop and with more precise control. Local control, or adjusting small parts of a photo without affecting anything else, has long been an important part of photography. In Lightroom 2, you can darken, lighten, and affect color and change sharpness and other aspects of specific areas in the photo simply by brushing your cursor across the areas. Photoshop has far more power in its Cloning and Healing Brush tools than Lightroom, but Lightroom offers simple cloning and healing that’s nondestructive. Lightroom supports the RAW formats of more cameras than Aperture. Lightroom provides the option of storing images outside the application in the file system. It costs less than photoshop. Download Why PhotoShop is advanced than Lightroom? There are countless image processing plug-ins on the market for doing specialized processing in Photoshop. For example, if your image needs sophisticated noise reduction, you can use the Noiseware plug-in with Photoshop to do a much better job or noise removal than Lightroom can do. Lightroom’s advantages over Aperture 3 Will always have better integration with Photoshop. Lightroom is backed by bigger and more active user community (So abundant availability for tutorials, etc.) Better noise reduction tool. Especially for photographers the Lens-distortion correction tool is perfect Lightroom Cons: • Have to Import images to work on them • Slows down with over 10,000 images in the catalog • For processing just one or two images this is a slower workflow Photoshop Pros: • ACR has the same RAW processing controls as Lightroom • ACR Histogram is specialized to the chosen color space (Lightroom is locked into ProPhoto RGB color space with an sRGB tone curve) • Don’t have to Import images to open in Bridge or ACR • Ability to customize processing of RAW images with Photoshop Actions Pricing and Availability Get LightRoomGet PhotoShop Latest version Of Photoshop can be purchased from Adobe store and Adobe authorized reseller and it costs US$999. Latest version of Aperture can be bought for US$199 from Apple Online store or Mac App Store. You can buy latest version of LightRoom from Adobe Store or Adobe Authorized reseller for US$299. Related posts:Adobe Photoshop CS5 vs Photoshop CS5 extended Web based Alternatives to Photoshop 10 Free Alternatives for Adobe Photoshop Software

Read the article

Setup Remote Access in Windows Home Server

- by Mysticgeek

One of the many awesome features of Windows Home Server, is the ability to access your server and other computers on your network remotely. Today we show you the steps to enable Remote Access to your home server from anywhere you have an Internet connection. Remote Access in Windows Home Server has a lot of great features like uploading and downloading files from shared folders, accessing files from machines on your network, and controling machines remotely (on supported OS versions). Here we take a look at the basics of setting it up, choosing a domain name, and verifying you can connect remotely. Setup Remote Access in Windows Home Server Open the Windows Home Server Console and click on Settings. Next select Remote Access, it is off by default, just click the button to turn it on. Wait while your router is configured for remote access, when it’s complete click Next. Notice that it will enable UPnP, if you don’t wish to have that enabled, you can manually forward the correct ports. If you have any problems with the router being automatically configured, we’ll be taking a look at a more detailed troubleshooting guide in the future. The router is successfully configured, and we can continue to the next process of configuring our domain name. The Domain Name Setup Wizard will start. Notice you will need a Windows Live ID to set it up –which is typically your hotmail address. If you don’t already have one, you can get one here. Type in your Live ID email address and password and click Next… Agree to the Home Server Privacy Statement and the Live Custom Domains Addendum. If you’re concerned about privacy and want to learn more about the domain addendum, make sure to read about it before agreeing. There is nothing abnormal to point out about either statement, but if this is your first time setting it up, it’s good to review the information. Now choose a name for the domain. You should select something that is easy to remember and identifies your home server. The name can contain up to 63 characters, numbers, letters, and hyphens…and must begin and end with a letter or number. When you have the name figured out click the Confirm button. Note: You can only register one domain name per Live ID. If the name isn’t already taken, you’ll get a confirmation message indicating it’s god to go. The wizard is complete and you can now access the home server from the URL provided. A few other things to point out after you’ve set it up…under Domain Name click on the Details button… Which pulls up the domain detail information and you can refresh the data to verify everything is working correctly. Or you can click the Configure button and then change or release your current domain name. Under Web site settings, you can change you site page headline to whatever you want it to be. Accessing Home Server Remotely After you’ve gotten everything setup for your home server domain, you can begin to access it when you’re away from home. Simply type in the domain address you created in the previous steps. The start page is rather boring…and to start accessing your data, click the Log On button in the upper right hand corner. Then enter in your home server credentials to gain access to your files, folders, and network computers. You won’t be able to log in with your administrator user account however, to protect security of your network. Once you’re logged in, you’ll be able to access different parts of your home server shares and network computers. Conclusion Now that you have Remote Access setup, you should be able to access and manage your files easily. Being able to access data from your home server remotely is great when you need to get certain files while on the road. The web UI is pretty self explanatory, works best in IE as ActiveX is required, and is smooth and easy to work with. In future articles we’ll be covering a lot more regarding remote access, including more of the available features, troubleshooting connection issues, and enabling access for other users. Similar Articles Productive Geek Tips GMedia Blog: Setting Up a Windows Home ServerHow to Remote Desktop to the Actual Server Console on Windows 2003Use Windows Vista Aero through Remote Desktop ConnectionAccess Your MySQL Server Remotely Over SSHShare Ubuntu Home Directories using Samba TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Penolo Lets You Share Sketches On Twitter Visit Woolyss.com for Old School Games, Music and Videos Add a Custom Title in IE using Spybot or Spyware Blaster When You Need to Hail a Taxi in NYC Live Map of Marine Traffic NoSquint Remembers Site Specific Zoom Levels (Firefox)

Read the article

Mobile HCM: It’s not the future, it is right now

- by Natalia Rachelson

Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} A guest post by Steve Boese, Director Product Strategy, Oracle I’ll bet you reached for your iPhone or Android or BlackBerry and took a quick look at email or Facebook or last night’s text messages before you even got out of bed this morning. Come on, admit it, it’s ok, you are among friends here. See, feel better now? But seriously, the incredible growth and near-ubiquity of increasingly powerful, capable, and for many of us, essential in our daily lives mobile devices has profoundly changed the way we communicate, consume information, socialize, and more and more, conduct business and get our work done. And if you doubt that profound change has happened, just think for a moment about the last time you misplaced your iPhone. The shivers, the cold sweats, the panic... We have all been there. And indeed your personal experiences with mobile technology echoes throughout the world - here are a few data points to consider: Market research firm IDC estimates 1.8 billion mobile phones will be shipped in 2012. A recent Pew study reports 46% of Americans own a smartphone of some kind. And finally in the USA, ownership of tablets like the iPad has doubled from 10% to 19% in the last year. So truly for the Human Resources leader, the question is no longer, ‘Should HR explore ways to exploit mobile devices and their always-on nature to better support and empower the modern workforce?’, but rather ‘How can HR best take advantage of smartphone and tablet capability to provide information, enable transactions, and enhance decision making?’. Because even though moving HCM applications to mobile devices seems inherently logical given today’s fast-moving and mobile workforces, and its promise to deliver incredible value to the organization, HR leaders also have to consider many factors before devising their Mobile HCM strategy and embarking on mobile HR technology projects. Here are just some of the important considerations for HR leaders as you build your strategies and evaluate mobile HCM solutions: Does your organization provide mobile devices to the workforce today, and if so, will the current set of deployed devices have the necessary capability and ecosystems to support your mobile HCM initiatives? Will you allow workers to use or bring their own mobile devices, (commonly abbreviated as ‘BYOD’), and if so are your IT and Security organizations in agreement and capable of supporting that strategy? Do you know which workers need access to mobile HCM applications? Often mobile HCM capability flows down in an organization, with executives and other ‘road-warrior’ types having the most immediate needs, followed by field sales staff, project managers, and even potential job candidates. But just as an organization will have to spend time understanding ‘who’ should have access to mobile HCM technology, the ‘what’ of the way the solutions should be deployed to these groups will also vary. What works and makes sense for the executive, (company-wide dashboards and analytics on an iPad), might not be as relevant for a retail store manager, (employee schedules, location-level sales and inventory data, transaction approvals, etc.). With Oracle Fusion HCM, we are taking an approach to mobile HR that encompasses not just the mobile solution needs for the various types of worker, but also incorporates the fundamental attributes of great mobile applications - the ability to support end-to-end transactions, apps that respond with lightning-fast speed, with functions that are embedded in a worker’s daily activities, and features that can be mashed-up easily with other business areas like Finance and CRM. Finally, and perhaps most importantly for the Oracle Fusion HCM team, delivering mobile experiences that truly enhance, enable, and empower the mobile workforce, and deliver on the design mantras of the best-in-class consumer applications, continues to shape and drive design decisions. Mobile is no longer the future, it is right now, and the cutting-edge HR leader of today will need to consider how mobile fits her HCM technology strategy from here on out. You can learn more about our ideas and plans for Oracle Fusion HCM mobile solutions at https://fusiontap.oracle.com/.

Read the article

Request Limit Length Limits for IIS’s requestFiltering Module

- by Rick Strahl

Today I updated my CodePaste.net site to MVC 3 and pushed an update to the site. The update of MVC went pretty smooth as well as most of the update process to the live site. Short of missing a web.config change in the /views folder that caused blank pages on the server, the process was relatively painless. However, one issue that kicked my ass for about an hour – and not foe the first time – was a problem with my OpenId authentication using DotNetOpenAuth. I tested the site operation fairly extensively locally and everything worked no problem, but on the server the OpenId returns resulted in a 404 response from IIS for a nice friendly OpenId return URL like this: http://codepaste.net/Account/OpenIdLogon?dnoa.userSuppliedIdentifier=http%3A%2F%2Frstrahl.myopenid.com%2F&dnoa.return_to_sig_handle=%7B634239223364590000%7D%7BjbHzkg%3D%3D%7D&dnoa.return_to_sig=7%2BcGhp7UUkcV2B8W29ibIDnZuoGoqzyS%2F%2FbF%2FhhYscgWzjg%2BB%2Fj10ZpNdBkUCu86dkTL6f4OK2zY5qHhCnJ2Dw%3D%3D&openid.assoc_handle=%7BHMAC-SHA256%7D%7B4cca49b2%7D%7BMVGByQ%3D%3D%7D&openid.claimed_id=http%3A%2F%2Frstrahl.myopenid.com%2F&openid.identity=http%3A%2F%2Frstrahl.myopenid.com%2F&openid.mode=id_res&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.ns.sreg=http%3A%2F%2Fopenid.net%2Fextensions%2Fsreg%2F1.1&openid.op_endpoint=http%3A%2F%2Fwww.myopenid.com%2Fserver&openid.response_nonce=2010-10-29T04%3A12%3A53Zn5F4r5&openid.return_to=http%3A%2F%2Fcodepaste.net%2FAccount%2FOpenIdLogon%3Fdnoa.userSuppliedIdentifier%3Dhttp%253A%252F%252Frstrahl.myopenid.com%252F%26dnoa.return_to_sig_handle%3D%257B634239223364590000%257D%257BjbHzkg%253D%253D%257D%26dnoa.return_to_sig%3D7%252BcGhp7UUkcV2B8W29ibIDnZuoGoqzyS%252F%252FbF%252FhhYscgWzjg%252BB%252Fj10ZpNdBkUCu86dkTL6f4OK2zY5qHhCnJ2Dw%253D%253D&openid.sig=h1GCSBTDAn1on98sLA6cti%2Bj1M6RffNerdVEI80mnYE%3D&openid.signed=assoc_handle%2Cclaimed_id%2Cidentity%2Cmode%2Cns%2Cns.sreg%2Cop_endpoint%2Cresponse_nonce%2Creturn_to%2Csigned%2Csreg.email%2Csreg.fullname&openid.sreg.email=rstrahl%40host.com&openid.sreg.fullname=Rick+Strahl A 404 of course isn’t terribly helpful – normally a 404 is a resource not found error, but the resource is definitely there. So how the heck do you figure out what’s wrong? If you’re just interested in the solution, here’s the short version: IIS by default allows only for a 1024 byte query string, which is obviously exceeded by the above. The setting is controlled by the RequestFiltering module in IIS 6 and later which can be configured in ApplicationHost.config (in \%windir\system32\inetsvr\config). To set the value configure the requestLimits key like so: <configuration> <security> <requestFiltering> <requestLimits maxQueryString="2048"> </requestLimits> </requestFiltering> </security> </configuration> This fixed me right up and made the requests work. How do you find out about problems like this? Ah yes the troubles of an administrator? Read on and I’ll take you through a quick review of how I tracked this down. Finding the Problem The issue with the error returned is that IIS returns a 404 Resource not found error and doesn’t provide much information about it. If you’re lucky enough to be able to run your site from the localhost IIS is actually very helpful and gives you the right information immediately in a nicely detailed error page. The bottom of the page actually describes exactly what needs to be fixed. One problem with this easy way to find an error: You HAVE TO run localhost. On my server which has about 10 domains running localhost doesn’t point at the particular site I had problems with so I didn’t get the luxury of this nice error page. Using Failed Request Tracing to retrieve Error Info The first place I go with IIS errors is to turn on Failed Request Tracing in IIS to get more error information. If you have access to the server to make a configuration change you can enable Failed Request Tracing like this: Find the Failed Request Tracing Rules in the IIS Service Manager. Select the option and then Edit Site Tracing to enable tracing. Then add a rule for * (all content) and specify status codes from 100-999 to capture all errors. if you know exactly what error you’re looking for it might help to specify it exactly to keep the number of errors down. Then run your request and let it fail. IIS will throw error log files into a folder like this C:\inetpub\logs\FailedReqLogFiles\W3SVC5 where the last 5 is the instance ID of the site. These files are XML but they include an XSL stylesheet that provides some decent formatting. In this case it pointed me straight at the offending module: Ok, it’s the RequestFilteringModule. Request Filtering is built into IIS 6-7 and configured in ApplicationHost.config. This module defines a few basic rules about what paths and extensions are allowed in requests and among other things how long a query string is allowed to be. Most of these settings are pretty sensible but the query string value can easily become a problem especially if you’re dealing with OpenId since these return URLs are quite extensive. Debugging failed requests is never fun, but IIS 6 and forward at least provides us the tools that can help us point in the right direction. The error message the FRT report isn’t as nice as the IIS error message but it at least points at the offending module which gave me the clue I needed to look at request restrictions in ApplicationHost.config. This would still be a stretch if you’re not intimately familiar, but I think with some Google searches it would be easy to track this down with a few tries… Hope this was useful to some of you. Useful to me to put this out as a reminder – I’ve run into this issue before myself and totally forgot. Next time I got it, right?© Rick Strahl, West Wind Technologies, 2005-2010Posted in ASP.NET Security

Read the article

SQL SERVER – PAGEIOLATCH_DT, PAGEIOLATCH_EX, PAGEIOLATCH_KP, PAGEIOLATCH_SH, PAGEIOLATCH_UP – Wait Type – Day 9 of 28

- by pinaldave

It is very easy to say that you replace your hardware as that is not up to the mark. In reality, it is very difficult to implement. It is really hard to convince an infrastructure team to change any hardware because they are not performing at their best. I had a nightmare related to this issue in a deal with an infrastructure team as I suggested that they replace their faulty hardware. This is because they were initially not accepting the fact that it is the fault of their hardware. But it is really easy to say “Trust me, I am correct”, while it is equally important that you put some logical reasoning along with this statement. PAGEIOLATCH_XX is such a kind of those wait stats that we would directly like to blame on the underlying subsystem. Of course, most of the time, it is correct – the underlying subsystem is usually the problem. From Book On-Line: PAGEIOLATCH_DT Occurs when a task is waiting on a latch for a buffer that is in an I/O request. The latch request is in Destroy mode. Long waits may indicate problems with the disk subsystem. PAGEIOLATCH_EX Occurs when a task is waiting on a latch for a buffer that is in an I/O request. The latch request is in Exclusive mode. Long waits may indicate problems with the disk subsystem. PAGEIOLATCH_KP Occurs when a task is waiting on a latch for a buffer that is in an I/O request. The latch request is in Keep mode. Long waits may indicate problems with the disk subsystem. PAGEIOLATCH_SH Occurs when a task is waiting on a latch for a buffer that is in an I/O request. The latch request is in Shared mode. Long waits may indicate problems with the disk subsystem. PAGEIOLATCH_UP Occurs when a task is waiting on a latch for a buffer that is in an I/O request. The latch request is in Update mode. Long waits may indicate problems with the disk subsystem. PAGEIOLATCH_XX Explanation: Simply put, this particular wait type occurs when any of the tasks is waiting for data from the disk to move to the buffer cache. ReducingPAGEIOLATCH_XX wait: Just like any other wait type, this is again a very challenging and interesting subject to resolve. Here are a few things you can experiment on: Improve your IO subsystem speed (read the first paragraph of this article, if you have not read it, I repeat that it is easy to say a step like this than to actually implement or do it). This type of wait stats can also happen due to memory pressure or any other memory issues. Putting aside the issue of a faulty IO subsystem, this wait type warrants proper analysis of the memory counters. If due to any reasons, the memory is not optimal and unable to receive the IO data. This situation can create this kind of wait type. Proper placing of files is very important. We should check file system for the proper placement of files – LDF and MDF on separate drive, TempDB on separate drive, hot spot tables on separate filegroup (and on separate disk), etc. Check the File Statistics and see if there is higher IO Read and IO Write Stall SQL SERVER – Get File Statistics Using fn_virtualfilestats. It is very possible that there are no proper indexes on the system and there are lots of table scans and heap scans. Creating proper index can reduce the IO bandwidth considerably. If SQL Server can use appropriate cover index instead of clustered index, it can significantly reduce lots of CPU, Memory and IO (considering cover index has much lesser columns than cluster table and all other it depends conditions). You can refer to the two articles’ links below previously written by me that talk about how to optimize indexes. Create Missing Indexes Drop Unused Indexes Updating statistics can help the Query Optimizer to render optimal plan, which can only be either directly or indirectly. I have seen that updating statistics with full scan (again, if your database is huge and you cannot do this – never mind!) can provide optimal information to SQL Server optimizer leading to efficient plan. Checking Memory Related Perfmon Counters SQLServer: Memory Manager\Memory Grants Pending (Consistent higher value than 0-2) SQLServer: Memory Manager\Memory Grants Outstanding (Consistent higher value, Benchmark) SQLServer: Buffer Manager\Buffer Hit Cache Ratio (Higher is better, greater than 90% for usually smooth running system) SQLServer: Buffer Manager\Page Life Expectancy (Consistent lower value than 300 seconds) Memory: Available Mbytes (Information only) Memory: Page Faults/sec (Benchmark only) Memory: Pages/sec (Benchmark only) Checking Disk Related Perfmon Counters Average Disk sec/Read (Consistent higher value than 4-8 millisecond is not good) Average Disk sec/Write (Consistent higher value than 4-8 millisecond is not good) Average Disk Read/Write Queue Length (Consistent higher value than benchmark is not good) Note: The information presented here is from my experience and there is no way that I claim it to be accurate. I suggest reading Book OnLine for further clarification. All of the discussions of Wait Stats in this blog is generic and varies from system to system. It is recommended that you test this on a development server before implementing it to a production server. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

Read the article

CodePlex Daily Summary for Sunday, March 07, 2010

CodePlex Daily Summary for Sunday, March 07, 2010New ProjectsAlgorithminator: Universal .NET algorithm visualizer, which helps you to illustrate any algorithm, written in any .NET language. Still in development.ALToolkit: Contains a set of handy .NET components/classes. Currently it contains: * A Numeric Text Box (an Extended NumericUpDown) * A Splash Screen base fo...Automaton Home: Automaton is a home automation software built with a n-Tier, MVVM pattern utilzing WCF, EF, WPF, Silverlight and XBAP.Developer Controls: Developer Controls contains various controls to help build applications that can script/write code.Dynamic Reference Manager: Dynamic Reference Manager is a set (more like a small group) of classes and attributes written in C# that allows any .NET program to reference othe...indiologic: Utilities of an IndioNeural Cryptography in F#: This project is my magistracy resulting work. It is intended to be an example of using neural networks in cryptography. Hashing functions are chose...Particle Filter Visualization: Particle Filter Visualization Program for the Intel Science and Engineering FairPólya: Efficient, immutable, polymorphic collections. .Net lacks them, we provide them*. * By we, we mean I; and by efficient, I mean hopefully so.project euler solutions from mhinze: mhinze project euler solutionsSilverlight 4 and WCF multi layer: Silverlight 4 and WCF multi layersqwarea: Project for a browser-based, minimalistic, massively multiplayer strategy game. Part of the "Génie logiciel et Cloud Computing" course of the ENS (...SuperSocket: SuperSocket, a socket application framework can build FTP/SMTP/POP server easilyToast (for ASP.NET MVC): Dynamic, developer & designer friendly content injection, compression and optimization for ASP.NET MVCNew ReleasesALToolkit: ALToolkit 1.0: Binary release of the libraries containing: NumericTextBox SplashScreen Based on the VB.NET code, but that doesn't really matter.Blacklist of Providers: 1.0-Milestone 1: Blacklist of Providers.Milestone 1In this development release implemented - Main interface (Work Item #5453) - Database (Work Item #5523)C# Linear Hash Table: Linear Hash Table b2: Now includes a default constructor, and will throw an exception if capacity is not set to a power of 2 or loadToMaintain is below 1.Composure: CassiniDev-Trunk-40745-VS2010.rc1.NET4: A simple port of the CassiniDev portable web server project for Visual Studio 2010 RC1 built against .NET 4.0. The WCF tests currently fail unless...Developer Controls: DevControls: These are the version 1.0 releases of these controls. Download the individually or all together (in a .zip file). More releases coming soon!Dynamic Reference Manager: DRM Alpha1: This is the first release. I'm calling it Alpha because I intend implementing other functions, but I do not intend changing the way current functio...ESB Toolkit Extensions: Tellago SOA ESB Extenstions v0.3: Windows Installer file that installs Library on a BizTalk ESB 2.0 system. This Install automatically configures the esb.config to use the new compo...GKO Libraries: GKO Libraries 0.1 Alpha: 0.1 AlphaHome Access Plus+: v3.0.3.0: Version 3.0.3.0 Release Change Log: Added Announcement Box Removed script files that aren't needed Fixed & issue in directory path Stylesheet...Icarus Scene Engine: Icarus Scene Engine 1.10.306.840: Icarus Professional, Icarus Player, the supporting software for Icarus Scene Engine, with some included samples, and the start of a tutorial (with ...mavjuz WndLpt: wndlpt-0.2.5: New: Response to 5 LPT inputs "test i 1" New: Reaction to 12 LPT outputs "test q 8" New: Reaction to all LPT pins "test pin 15" New: Syntax: ...Neural Cryptography in F#: Neural Cryptography 0.0.1: The most simple version of this project. It has a neural network that works just like logical AND and a possibility to recreate neural network from...Password Provider: 1.0.3: This release fixes a bug which caused the program to crash when double clicking on a generic item.RoTwee: RoTwee 6.2.0.0: New feature is as next. 16649 Add hashtag for tweet of tune.Now you can tweet your playing tune with hashtag.Visual Studio DSite: Picture Viewer (Visual C++ 2008): This example source code allows you to view any picture you want in the click of a button. All you got to do is click the button and browser via th...WatchersNET CKEditor™ Provider for DotNetNuke: CKEditor Provider 1.8.00: Whats New File Browser: Folders & Files View reworked File Browser: Folders & Files View reworked File Browser: Folders are displayed as TreeVi...WSDLGenerator: WSDLGenerator 0.0.0.4: - replaced CommonLibrary.dll by CommandLineParser.dll - added better support for custom complex typesMost Popular ProjectsMetaSharpSilverlight ToolkitASP.NET Ajax LibraryAll-In-One Code FrameworkWindows 7 USB/DVD Download Toolニコ生アラートWindows Double ExplorerVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2Caliburn: An Application Framework for WPF and SilverlightArkSwitchMost Active ProjectsUmbraco CMSRawrSDS: Scientific DataSet library and toolsBlogEngine.NETjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryIonics Isapi Rewrite FilterFarseer Physics EngineFasterflect - A Fast and Simple Reflection APIFluent Assertions

Search Results

Search found 4509 results on 181 pages for 'logical domains'.

Page 164/181 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171 | Next Page >

- by Shoshomiga

- by Warren P

- by NewToDPM

- by Yohann

- by Jace

- by kyrpas

- by jessie

- by Enigma

- by karthik

- by dcerecedo

- by user318772

- by gkb0986

- by Oldek

- by BreezyChick89

- by JohnMerlino

- by ajay

- by user1514042

- by eJugnoo

- by alaa9jo

- by Aditi

- by Mysticgeek

- by Natalia Rachelson

- by Rick Strahl

- by pinaldave

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171 | Next Page >