Search Results

Search found 23950 results on 958 pages for 'ie8 64 bit'.

Page 165/958 | < Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• XP VM not detecting USB keyboard or mouse from Windows 7 host

  - by Ian Kemp

  I've been using a Windows XP Pro VM (32-bit, SP3) for months on my work PC (Windows 7 64-bit) with no problems, with a PS/2 keyboard and a standard optical USB mouse. Today I copied this VM onto my home PC, which is also Windows 7 64-bit but with a G15 USB keyboard and MX518 USB mouse. For some reason the VM does not accept input from the keyboard or mouse, which makes it almost impossible to use. (Unity works but is not an option). Both my home and work PC are running VMware player 3.1.0. My keyboard and mouse show up as USB devices in the bottom-right of the VMware Player window, and if I click them I have the standard option to "Connect (Disconnect from host)". I have selected this option for the keyboard, and then the VM happily accepts keyboard input, but of course my host PC no longer does. It seems like VMware is seeing my keyboard and mouse as USB devices and not input devices. I've tried sending the keyboard input to the guest and reinstalling VMware Tools, but that achieved nothing. I'm certain it's a problem with the VM, and not the XP install, as I also can't use F12 to enter the VMware BIOS when the VM is powering up.

  Read the article

• program to track recent saved files or downloads?

  - by DiegoDD

  Back to windows XP times, i used a program named Ava Find that can find any file in the system, but a really nice feature it had, called "scout bot" that automatically finds new files, that is, recently created. More info here: AvaFind For example, if i saved or downloaded a file (in any program), but i cant remember its name or where i put it, i just simply looked at the scoutbot list, and it showed me the most recent files, and then i could just open them from there, or jump to their path. Since i changed to windows 7 (passing through vista), the program no longer works. It simply keeps indexing forever and never finds anything. I don't know if it is not compatible with win 7 itself, or because the fact that my windows 7 is 64 bit. I already tried to contact the Avafind creators, but they never answered, and the program seems to be no longer supported (although the site still works). Now, is there a similar program that finds RECENT files? e.g. listing the most recently saved files, system-wide (or even limiting it to some folders, discs)? And that of course, that is confirmed to work with win 7 64 bit. I know that there are many programs that can find any file, like everything, but what i want is to find recent files and their paths, without knowing their name or e. "everything" also can sort results by date, which is almost what i need, simply to look for part of the file name or extension, and get the most recent one. but if i get to many results, it takes a while, plus, i STILL need to know the name or at least extension of the file. What i want is simply a "Most recently Saved files" tool. i.e., a replacement for Scout Bot in Ava Find. Do you know any alternative?

  Read the article

• Windows 7 Paging file apparently not being used

  - by Daniel F.

  I'm running Windows 7 Home Premium 32bit on a mobo with 24GB RAM. Of those 24GB, 20GB are assigned as a RAMDISK via ASRock XFastRAM. This RAMDISK has the drive letter X assigned to it. On X:\ I'm storing the temporary files folder, as well as pagefile.sys. Pagefile.sys has 6GB of size. The X:\ has usually around 14GB free space, so the temporary files are negligible, it's mostly the browsers which are storing their caches on there. Now my issue is that Firefox is crashing a lot on me, no error message pops up, but I know that this is because it's out of memory. I could kind of live with that, but now that I switched from using Eclipse to Android Studio, I know that I'm in trouble, because Java isn't capable of allocating, and Android Studio, together with the Java instances it launches, is quite a memory hog. So I tried to figure out what's wrong, and apparently Windows isn't swapping out memory onto the paging file. While my applications are crashing (firefox) / not starting (java vm's), the paging file is only using constantly around 15% of its size (checked with the performance monitor). 15% equals to 1GB aprox. I know that the correct solution would be to switch to 64 bit Windows, but I had to use the 32 bit version because of driver issues which I had about two years ago, and I guess that I'll have them again if I reformat and install the 64 bit version. Also, the machine is running quite stable, the only issue is the memory, so I'd like to use it as it is (as the apps are installed and configured) Is there a way to make Windows use the paging file more efficiently? None of my processes require more than 1GB, I'd just like it to swap out some seldomly used stuff, like GoogleCrashHandler.exe and stuff like that in order to have "more physical memory avaliable". Is that possible?

  Read the article

• Running batch file through a service.

  - by wallz

  I'm trying to schedule a batch file to run through a third party application, however the output file doesn't get created in the directory. If I run the .BAT file from the command line, it works and the file gets created. Also using the Windows Schedule will also succeed. Basically, the 3rd party software will schedule the .BAT file and it shows success within the 3rd party user interface. The difference between running from the command prompt and the software, is that the software will use its Windows service to launch the batch. The 3rd party software will show success since it was able to successfully call the .BAT file to run, however it has no control of the other EXE's that's being called within the script. I'm able to run a simple .BAT file in the 3rd party software, for example a copy command. The .BAT I'm having problems with calls a compiled EXE which launches Excel to create a file to a location. The .bat file calls something.exe, which then calls Excel.exe: C:\something.exe -o D:\filename.xlsm C:\filename.xlsm refresh_pivot Do you think it's a permissions issue? I used Process Monitor to verify any Access Denied errors but everything seems to be working according to the trace. It worked on a non-64-bit OS, I'm currently using Win2008 64-bit.

  Read the article

• Why can't I mount an image hosted on a read-only HFS+ partition via Boot Camp?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• Why is windows not able to create a system partition?

  - by hughes

  I'm reinstalling Windows 7 64 bit, and I encountered an issue I've never seen before. I have a legit copy of Win 64 Professional, and I've installed it probably a half dozen times on this machine in the past without a problem. Googling the error only brings me to issues with people who are upgrading to win7. The drive itself seems to not have a problem. I can mount it on other systems and I can create an NTFS partition on it on other machines. I can install Ubuntu on it without any issues. Additionally, if I try using my alternate backup hard drive, the installer gives the same error. I have run diskpart from the setup page and clean seems to report that all is well. However, I cannot get past the screen below, which says Setup was unable to create a new system partition or locate an existing system partition. This happens regardless of whether or not the disk space is already allocated. What is causing this? How do I solve or get past this?

  Read the article

• Why do disk images hosted on a read-only HFS+ partition behave differently?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Route web traffic through a separate iterface

  - by tkane

  I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Screen randomly goes blue/black/white

  - by FubsyGamer

  Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

  Read the article

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Second CPU missing of Dual Core

  - by Zardoz

  My Lenovo T61 has a dual core CPU. I just noticed that under Ubuntu 10.10 only one CPU is recognized. I know that once both CPUs worked. Not sure since when the second CPU is missing. Maybe since the last kernel update. Currently I am using linux-image-2.6.35-23-generic (for x86_64). What can I do to enable the second CPU again? Here the ouput of /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping : 6 cpu MHz : 800.000 cache size : 3072 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 4189.99 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: Any help is welcome. I really need that CPU power for my work here.

  Read the article

• apache segmentation error

  - by lush

  I can't start Apache with the following errors: [root@web]# /etc/init.d/httpd start Starting httpd: /bin/bash: line 1: 19232 Segmentation fault /usr/sbin/httpd [root@web]# /usr/sbin/apachectl -k start /usr/sbin/apachectl: line 102: 19919 Segmentation fault $HTTPD $OPTIONS $ARGV I use webmin control panel and I've already tried re-installing Apache from scratch. Can someone advise what else I should try to do? Many thanks. UPDATE: The only line is always written in the error logs which seems not to be very important: [Mon Nov 14 19:00:09 2011] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) UPDATE 2: I've recently had the error below in the logs. Looks like some modules are incompatible, so I've just disabled these extensions: fileinfo and mcrypt in my php.ini. I should be able to start the web server without them. PHP Warning: PHP Startup: fileinfo: Unable to initialize module\nModule compiled with module API=20050922, debug=0, thread-safety=0\nPHP compiled with module API=20060613, debug=0, thread-safety=0\nThese options need to match\n in Unknown on line 0 PHP Warning: Module 'mcrypt' already loaded in Unknown on line 0 UPDATE 3: [root@web]# file /usr/sbin/httpd /usr/sbin/httpd: ELF 64-bit LSB shared object, AMD x86-64, version 1 (SYSV), for GNU/Linux 2.6.9, stripped [root@web]# uname -m x86_64

  Read the article

• Multiple copies off the same printer on Windows 7 from PrintUIEntry

  - by Kev

  I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

  Read the article

• disk partition centos

  - by FlourishDNA

  I am setting up server for hosting two WordPress which has size of around 70GB. I have already installed CentOS as OS and I would like to partition the Disk. Is there any tool which can help me or can someone guide me though the process as I am not expert is SSH commands. Here are some output that might help. OS: CentOS release 6.3 fdisk -l Disk /dev/xvdb: 214.7 GB, 214748364800 bytes 255 heads, 63 sectors/track, 26108 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b91e0 Device Boot Start End Blocks Id System Disk /dev/xvda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e542c Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/vg_flourish-lv_root: 16.7 GB, 16718495744 bytes 255 heads, 63 sectors/track, 2032 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_flourish-lv_swap: 4227 MB, 4227858432 bytes 255 heads, 63 sectors/track, 514 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 df Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_flourish-lv_root 16070076 758184 14495560 5% / tmpfs 958500 0 958500 0% /dev/shm /dev/xvda1 495844 31926 438318 7% /boot df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_flourish-lv_root 16G 741M 14G 5% / tmpfs 937M 0 937M 0% /dev/shm /dev/xvda1 485M 32M 429M 7% /boot Thanks

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• VirtualName-based local development host behind corporate proxy (MAMP)

  - by geerlingguy

  I am behind a corporate proxy server/firewall, and this firewall seems to not be too happy with my idea of local development. On my home computer (Mac/Leopard), I have MAMP running, with a rule in /etc/hosts that directs dev.example.com to 127.0.0.1, and I have a virtualhost set up in the httpd.conf file which works great for me. However, at work, I set up the exact same configuration, but am not able to access dev.example.com, likely due to some address/DNS translation going on via the proxy server. Here are the relevant details from Terminal: $ ping dev.example.com PING dev.example.com (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.025 ms $ host dev.example.com Host dev.example.com not found: 3(NXDOMAIN) I've tried adding dev.example.com to the list of bypass addresses in System Preferences (the 'Bypass proxy settings for these Hosts & Domains' list), but that had no effect. Is there any way I can develop locally using name-based hosts at work? I can access localhost, but can't get to the dev.example.com (or any other custom virtualhosts) here at work, which complicates other matters related to the sites on which I'm working...

  Read the article

• Exim, hot to route local mail to other adress

  - by kheraud

  I have setuped an Exim4 server on my debian wheezy server. This mail server only sends mail coming from localhost. The purpose is sending mail for my website. I have cron tasks and other services generating mails for root user. These mails are not stored in /var/mail as before, but sent by exim to [email protected]. I try to make exim send mails for root to [email protected] rather than [email protected]. I tried adding a .forward in /root with [email protected] as content. I tried also changing /etc/aliases with root: [email protected]. The fact is that routing works for root@localhost but not for root which is resolved as [email protected] I tested how routing is resolved with exim -bt : root@srv02:~# exim -bt root@localhost R: system_aliases for root@localhost R: dnslookup for [email protected] [email protected] <-- root@localhost router = dnslookup, transport = remote_smtp host gmail-smtp-in.l.google.com [173.194.67.27] MX=5 host alt1.gmail-smtp-in.l.google.com [74.125.143.27] MX=10 host alt2.gmail-smtp-in.l.google.com [74.125.25.27] MX=20 host alt3.gmail-smtp-in.l.google.com [173.194.64.27] MX=30 host alt4.gmail-smtp-in.l.google.com [74.125.142.27] MX=40 root@srv02:~# exim -bt root R: dnslookup for [email protected] [email protected] router = dnslookup, transport = remote_smtp host aspmx.l.google.com [173.194.78.27] MX=1 host alt1.aspmx.l.google.com [74.125.143.27] MX=5 host alt2.aspmx.l.google.com [74.125.25.27] MX=5 host alt4.aspmx.l.google.com [74.125.142.27] MX=10 host alt3.aspmx.l.google.com [173.194.64.27] MX=10 I bet this is a matter of how my server is configured (rather than how exim is configured). But to understand well I would like to have a solution for both : how to have root resolved as root@localhost ? how to have [email protected] routed to [email protected] ?

  Read the article

• Migrating ODBC information through a batch file

  - by DeskSide

  I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• File corruption (bad checksums) in large files copied to VMware guest

  - by AllanA

  In setting up a development lab, I've got a desktop system running ESXi 4.1.0 (free license) on SATA RAID 0 (already purchased and configured when I started this job; I'm open to hardware input as it pertains to my problem.) Its guests so far include two Win2008 Server R2 64-bit VMs and on Ubuntu 10.04 64-bit VM. I'm installing onto the Windows servers. We've been copying off some fairly large files (over a gigabyte) for an installation, hoping to install more quickly from a (virtual) hard drive than from the network for from BD-ROM. The problem is that they keep coming up with different checksums from the originals. The file sizes are the same, but md5sum reports different numbers (and so does the installer, as it refuses to continue when the checksums don't match.) I've tried copying directly from the BD-ROM (attaching the OS drive to the host system's physical drive). I've tried copying the large files onto a co-worker's Windows machine from his Blu-Ray drive; when I do that, the checksums match. But when I copy from his machine to the VM guest over a network share, the checksums no longer match. Thinking this meant a corrupt destination drive, I deleted it in vSphere and added another freshly created drive. The problem persists. I'm not sure what to try next.

  Read the article

• Windows XP Freezes

  - by Jim Fell

  Hello. I'm running a machine with Windows XP Professional 64-bit. Every so often, it will freeze for no apparent reason. That is, everything stops responding, except the mouse. I can move the mouse around, but I can't click on anything. Keyboard input is also not accepted/received when this problem occurs. The three-finger salute fails to bring up the Task Manager. Even pressing the power button on my computer fails to shut it down. The only way out of this that I have found is to hard-reboot the machine (i.e. pull power or hold power button in for 10 seconds). This problem was occurring on the system when it had all its updates and after a fresh install when not everthing was quite yet updated. I've run the Scandisk utility and the latest version Memtest86 that supports 64-bit architecture; neither found any errors. The last time this happened was on a fresh install of Windows. Only Nero Essentials, Avast antivirus (disabled), Firefox, and Spybot were installed. I was not running Nero, Firefox, or Spybot at the time, and Avast was disabled, so I'm pretty certain this is a Windows issue. Is anybody familiar with this problem or have any pointers? Thanks.

  Read the article

< Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >