Search Results

Search found 4620 results on 185 pages for 'serial over lan'.

Page 165/185 | < Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >

• python extract from switch output

  - by household2

  I have some info back from a LAN switch as below Vlan 1 is administratively down, line protocol is down Vlan 2 is up, line protocol is up Helper address is 192.168.0.2 Vlan 3 is up, line protocol is up Helper address is not set Vlan 4 is up, line protocol is up Helper address is 192.168.0.2 Vlan 5 is down, line protocol is down Helper address is 192.168.0.2 Vlan 6 is down, line protocol is down Helper address is not set Helper address is not set And the output I'm trying for is Vlan 1,admin down,n/a Vlan 2,up/up, 192.168.0.2 Vlan 3, up/up, not set Vlan 4, up/up, 192.168.0.2 Vlan 5, down/down, 192.168.0.2 Vlan 6, down/down, not set So the helper isn't always there (line 1) sometimes it's set sometimes it isn't, sometimes there are two lines (last Vlan - I only need 1) and the Vlan can have states of admin down, up/up, up/down (not here) and down down. So using Python and pexpect I can get the above output, but I'm having difficulty parsing out the consecutive lines. I've tried enumerate and then use key+1 for the next line, but the fact that there can be 0,1 or 2 lines following the Vlan screws me. Any ideas please?

  Read the article

• Time Service will not start on Windows Server - System error 1290

  - by paradroid

  I have been trying to sort out some time sync issues involving two domain controllers and seem to have ended up with a bigger problem. It's horrible. They are both virtual machines (one being on Amazon EC2), which I think may complicate things regarding time servers. The primary DC with all the FSMO roles is on the LAN. I reset its time server configuration like this (from memory): net stop w32time w23tm /unregister shutdown /r /t 0 w32tm /register w32tm /config /manualpeerlist:”0.uk.pool.ntp.org,1.uk.pool.ntp.org,2.uk.pool.ntp.org,3.uk.pool.ntp.org” /syncfromflags:manual /reliable:yes /update W32tm /config /update net start w32time reg QUERY HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Config /v AnnounceFlags I checked to see if it was set to 0x05, which it was. The output for... w32tm /query /status Leap Indicator: 0(no warning) Stratum: 1 (primary reference - syncd by radio clock) Precision: -6 (15.625ms per tick) Root Delay: 0.0000000s Root Dispersion: 10.0000000s ReferenceId: 0x4C4F434C (source name: "LOCL") Last Successful Sync Time: 10/04/2012 15:03:27 Source: Local CMOS Clock Poll Interval: 6 (64s) While this was not what was intended, I thought I would sort it out after I made sure that the remote DC was syncing with it first. On the Amazon EC2 remote replica DC (Windows Server 2008 R2 Core)... net stop w32time w32tm /unregister shutdown /r /t 0 w32time /register net start w32time This is where it all goes wrong System error 1290 has occurred. The service start failed since one or more services in the same process have an incompatible service SID type setting. A service with restricted service SID type can only coexist in the same process with other services with a restricted SID type. If the service SID type for this service was just configured, the hosting process must be restarted in order to start this service. I cannot get the w32time service to start. I've tried resetting the time settings and tried to reverse what I have done. The Ec2Config service cannot start either, as it depends on the w32time service. All the solutions I have seen involve going into the telephony service registry settings, but as it is Server Core, it does not have that role, and I cannot see the relationship between that and the time service. w32time runs in the LocalService group and this telephony service which does not exist on Core runs in the NetworkService group. Could this have something to do with the process (svchost.exe) not being able to be run as a domain account, as it now a domain controller, but originally it ran as a local user group, or something like that? There seem to be a lot of cases of people having this problem, but the only solution has to do with the (non-existant on Core) telephony service. Who even uses that?

  Read the article

• Using Supermicro IPMI behind a Proxy?

  - by Stefan Lasiewski

  This is a SuperMicro server with a X8DT3 motherboard which contains an On-board IPMI BMC. In this case, the BMC is a Winbond WPCM450). I believe many Dell servers use this a similar BMC model. A common practice with IPMI is to isolated it to a private, non-routable network. In our case all IPMI cards are plugged into a private management LAN at 192.168.1.0/24 which has no route to the outside world. If I plug my laptop into the 192.168.1.0/24 network, I can verify that all IPMI features work as expected, including the remote console. I need to access all of the IPMI features from a different network, over some sort of encrypted connection. I tried SSH port forwarding. This works fine for a few servers, however, we have close to 100 of these servers and maintaining a SSH client configuration to forward 6 ports on 100 servers is impractical. So I thought I would try a SOCKS proxy. This works, but it seems that the Remote Console application does not obey my systemwide proxy settings. I setup a SOCKS proxy. Verbose logging allows me to see network activity, and if ports are being forwarded. ssh -v -D 3333 [email protected] I configure my system to use the SOCKS proxy. I confirm that Java is using the SOCKS proxy settings. The SOCKS proxy is working. I connect to the BMC at http://192.168.1.100/ using my webbrowser. I can log in, view the Server Health, power the machine on or off, etc. Since SSH verbose logging is enabled, I can see the progress. Here's where it get's tricky: I click on the "Launch Console" button which downloads a file called jviewer.jnlp. JNLP files are opened with Java Web Start. A Java window opens. The titlebar says says "Redirection Viewer" in the title bar. There are menus for "Video" "Keyboard" "Mouse", etc. This confirms that Java is able to download the application through the proxy, and start the application. 60 seconds later, the application times out and simply says "Error opening video socket". Here's a screenshot. If this worked, I would see a VNC-style window. My SSH logs show no connection attempts to ports 5900/5901. This suggests that the Java application started the VNC application, but that the VNC application ignores the systemwide proxy settings and is thus unable to connect to the remote host. Java seems to obey my systemwide proxy settings, but this VNC application seems to ignore it. Is there any way for me to force this VNC application to use my systemwide proxy settings?

  Read the article

• Internet Explorer keeps asking for NTLM credentials in Intranet zone

  - by Tomalak

  Long text, sorry for that. I'm trying to be as specific as possible. I'm on Windows 7 and I experience a very frustrating Internet Explorer 8 behavior. I'm in a company LAN with some intranet servers and a proxy for connecting with the outside world. On sites that are clearly recognized as being "Local Intranet" (as indicated in the IE status bar) I keep getting "Windows Security" dialog boxes that ask me to log in. These pages are served off an IIS6 with "Integrated Windows Security" enabled, NTFS permits Everyone:Read on the files themselves. If I enter my Windows credentials, the page loads fine. However, the dialog boxes will be popping up the next time, regardless if I ticked "Remember my credentials" or not. (Credentials are stored in the "Credential Manager" but that does not make any difference as to how often these login boxes appear.) If I click "Cancel", one of two things can happen: Either the page loads with certain resources missing (images, styleheets, etc), or it does not load at all and I get HTTP 401.2 (Unauthorized: Logon Failed Due to Server Configuration). This depends on whether the logon box was triggered by the page itself, or a referenced resource. The behavior appears to be completely erratic, sometimes the pages load smoothly, sometimes one resource triggers a logon message, sometimes it does not. Even simply re-loading the page can result in changed behavior. I'm using WPAD as my proxy detection mechanism. All Intranet hosts do bypass the proxy in the PAC file. I've checked every IE setting I can think of, entered host patterns, individual host names, IP ranges in every thinkable configuration to the "Local Intranet" zone, ticked "Include all sites that bypass the proxy server", you name it. It boils down to "sometimes it just does not work", and slowly I'm losing my mind. ;-) I'm aware that this is related to IE not automatically passing my NTLM credentials to the webserver but asking me instead. Usually this should only happen for NTLM-secured sites that are not recognized as being in the "Intranet" zone. As explained, this is not the case here. Especially since half of a page can load perfectly and without interruption and some page's resources (coming from the same server!) trigger the login message. I've looked at http://support.microsoft.com/kb/303650, which gives the impression of describing the problem, but nothing there seems to work. And frankly, I'm not certain if "manually editing the registry" is the right solution for this kind of problem. I'm not the only person in the world with an IE/intranet/IIS configuration, after all. I'm at a loss, can somebody give me a hint?

  Read the article

• Getting problem while capturing image through web cam in Java -OpenCV code.

  - by Chetan

  Hi.. I am developing Face detector using OpenCV library in java... I have written sample code for this,but it is giving Error while capturing image. can any one help please. Here is the code import java.awt.; import java.awt.event.; import java.awt.image.MemoryImageSource; import hypermedia.video.OpenCV; @SuppressWarnings("serial") public class FaceDetection extends Frame implements Runnable { ///Main method. public static void main(String[] args) { //System.out.println( "\nOpenCV face detection sample\n" ); new FaceDetection(); } // program execution frame rate (millisecond) final int FRAME_RATE = 1000/30; OpenCV cv = null; // OpenCV Object Thread t = null; // the sample thread // the input video stream image Image frame = null; // list of all face detected area Rectangle[] squares = new Rectangle[0]; //** Setup Frame and Object(s). FaceDetection() { super( "Face Detection" ); // OpenCV setup cv = new OpenCV(); //cv.capture(1, 1, 100); cv.capture( 320, 240 ); cv.cascade( OpenCV.CASCADE_FRONTALFACE_ALT ); // frame setup this.setBounds( 100, 100, cv.width, cv.height ); this.setBackground( Color.BLACK ); this.setVisible( true ); this.addKeyListener( new KeyAdapter() { public void keyReleased( KeyEvent e ) { if ( e.getKeyCode()==KeyEvent.VK_ESCAPE ) { // ESC : release OpenCV resources cv.dispose(); System.exit(0); } } } ); // start running program t = new Thread( this ); t.start(); } // Draw video frame and each detected faces area. public void paint( Graphics g ) { // draw image g.drawImage( frame, 0, 0, null ); // draw squares g.setColor( Color.RED ); for( Rectangle rect : squares ) g.drawRect( rect.x, rect.y, rect.width, rect.height ); } @SuppressWarnings("static-access") public void run() { while( t!=null && cv!=null ) { try { t.sleep( FRAME_RATE ); // grab image from video stream cv.read(); // create a new image from cv pixels data MemoryImageSource mis = new MemoryImageSource( cv.width, cv.height, cv.pixels(), 0, cv.width ); frame = createImage( mis ); // detect faces squares = cv.detect( 1.2f, 2, OpenCV.HAAR_DO_CANNY_PRUNING, 20, 20 ); // of course, repaint repaint(); } catch( InterruptedException e ) {;} } } } Error while starting capture : device 0

  Read the article

• How to read MAC address with python

  - by getjoefree

  Earlier, I could read MAC address with awk tools in Windows or Windows PE 4.0, but now it don't support Windows PE 4.0 64-bit. I want to get this result "set mac=A4BADB9D1E8E" with python 2.6, who could help to me. As follows: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" > D:\LOG\WINMAC.BAT getmac.sed: /Realtek/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; } and "ipconfig -all" command log as bellows ipconfig -all >mac.log Ethernet adapter Ethernet: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : WKSCN.WISTRON Description . . . . . . . . . . . : Realtek PCIe FE Family Controller Physical Address. . . . . . . . . : 24-B6-FD-1F-41-E7 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes --------------------------------------- we can get Physical Address when plug in lan cable, but not plug the network cable, it is impossible to obtain IP address.

  Read the article

• Windows 7 extremely slow login, exchange performance, printer enumeration, etc...

  - by Jeff

  Background: I have a fresh copy of Windows 7 Professional x64 on a Dell Latitude E6500. The laptop has 8GB RAM, 250GB drive, and all Intel peripherals (net/wifi/graphics). All available Windows updates, as well as hardware drivers are installed. The IT folks where I work joined the computer to our Windows 2003-based Active Directory domain. There are no errors in any logs that we've looked at, and Group Policy templates appear to have applied properly. Problem: Every time I turn on or reboot the computer, it takes between 2 to 10 (all times are actual) minutes after successfully typing my username/password to get to my desktop. My login script does not always run. Sometimes I get a black screen, and a couple of minutes later the login script will pop up and take up to 10 minutes to complete. I can get around this by hitting cntrl-shift-esc and running explorer.exe from the Task Manager. The login script continues to hang, but I can minimize it and go on about my business. Either way, it generally throws errors prior to completing. I often get slow or failed connectivity to Exchange via Outlook. When I bring up printer dialogs, they take several minutes to populate, and block the calling app while doing so. Copies to SMB shares are very slow. On my home network, everything works fine. On both the work network and home network, I can use remote internet resources just fine. Web pages pull up, remote VPN's are fine, I can max out bandwidth on SpeakEasy Speed Test. I can get almost max bandwidth transferring FTP/HTTP over a LAN. Another symptom of the problem is that when I first log in, the work network shows as "Identifying" for a long time in the Network and Sharing Center, and will often then change to the name of the work domain, but say "Unauthenticated Network". Note that this computer previously ran Windows Vista with none of these problems. Attempts to Fix: Installed the Win7 admin pack Uninstalled/reinstalled all hardware drivers Verified Active Directory DNS settings (Vista works relatively well on the same network) Reset all TCP/IP settings on all adapters using the netsh commands to do so Disabled ipv6 on all adapters Disable wifi adapter while on work network Locked the network card to 100/Full, 1000/Full; also tried Auto Added various important addresses to hosts file (exchange, dns, ad) -- removed when didn't help My background is a jpeg (sounds unrelated but there is apparently a win7 login bug related to solid color background) More I have forgotten The IT staff at my company indicated they believe this is due to having Windows 2003 AD servers and not having any Windows 2008 R2 AD servers. Other than that, they have no advice or assistance to offer other than a rebuild (already tried that once with similar symptoms), or downgrade to Vista. Any thoughts out there?

  Read the article

• Lion built-in VPN client times out connecting to Windows 2003 PPTP server

  - by beporter

  I have a new iMac with OS X 10.7 (Lion) on it that refuses to connect to a PPTP-based VPN server (running Windows 2003 SBS). To shortcut past a lot of questions: There is a Dell workstation running Windows 7 on the same LAN as the Mac that is able to establish a PPTP connection to the same VPN server using the same credentials. That would seem to rule out any possible problems with the server, the port forwards on the server's firewall, the internet connection between the two, and the router local to the Dell and iMac. Here's a "verbose" dump of the PPP log from the iMac: Tue Sep 6 10:13:11 2011 : using link 0 Tue Sep 6 10:13:11 2011 : Using interface ppp0 Tue Sep 6 10:13:11 2011 : Connect: ppp0 socket[34:17] Tue Sep 6 10:13:11 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0, interfaceIndex: 0, Protocol: None, Private Port: 0, Public Address: 45f6f181, Public Port: 0, TTL: 0. Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0 inconsistent. is Connected: 1, Previous interface: 4, Current interface 0 Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0 initialized. is Connected: 1, Previous publicAddress: (0), Current publicAddress 45f6f181 Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0 fully initialized. Flagging up Tue Sep 6 10:13:14 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:17 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:20 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:23 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:26 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:29 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:32 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:35 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:38 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:41 2011 : LCP: timeout sending Config-Requests Tue Sep 6 10:13:41 2011 : Connection terminated. Tue Sep 6 10:13:41 2011 : PPTP disconnecting... Tue Sep 6 10:13:41 2011 : PPTP clearing port-mapping for en0 Tue Sep 6 10:13:41 2011 : PPTP disconnected The error seems to be focused around the line, LCP: timeout sending Config-Requests, but I haven't had any luck in finding troubleshooting information for this. I've tried completely deleting the entire VPN "connection" from the Network prefpane and recreating it from scratch. I am certain the connection details are correct because they exactly match what successfully connects from the Win7 machine sitting next to the iMac. Any suggestions?

  Read the article

• Reality behind wireless security - the weakness of encrypting

  - by Cawas

  I welcome better key-wording here, both on tags and title, and I'll add more links as soon as possible. For some years I'm trying to conceive a wireless environment that I'd setup anywhere and advise for everyone, including from big enterprises to small home networks of 1 machine. I've always had the feeling using any kind of the so called "wireless security" methods is actually a bad design. I'm talking mostly about encrypting and pass-phrasing (which are actually two different concepts), since I won't even considering hiding SSID and mac filtering. I understand it's a natural way of thinking. With cable networking nobody can access the network unless they have access to the physical cable, so you're "secure" in the physical way. In a way, encrypting is for wireless what walling (building walls) is for the cables. And giving pass-phrases is adding a door with a key. But the cabling without encryption is also insecure. Someone just need to plugin and get your data! And while I can see the use for encrypting data, I don't think it's a security measure in wireless networks. As I said elsewhere, I believe we should encrypt only sensitive data regardless of wires. And passwords should be added to the users, always, not to wifi. For securing files, truly, best solution is backup. Sure all that doesn't happen that often, but I won't consider the most situations where people just don't care. I think there are enough situations where people actually care on using passwords on their OS users, so let's go with that in mind. For being able to break the walls or the door someone will need proper equipment such as a hammer or a master key of some kind. Same is true for breaking the wireless walls in the analogy. But, I'd say true data security is at another place. I keep promoting the Fonera concept as an instance. It opens up a free wifi port, if you choose so, and anyone can connect to the internet through that, without having any access to your LAN. It also uses a QoS which will never let your bandwidth drop from that public usage. That's security, and it's open. And who doesn't want to be able to use internet freely anywhere you can find wifi spots? I have 3G myself, but that's beyond the point here. If I have a wifi at home I want to let people freely use it for internet as to not be an hypocrite and even guests can easily access my files, just for reading access, so I don't need to keep setting up encryption and pass-phrases that are not whole compatible. I'll probably be bashed for promoting the non-usage of WPA 2 with AES or whatever, but I wanted to know from more experienced (super) users out there: what do you think? Is there really a need for encryption to have true wireless security?

  Read the article

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either.

  Read the article

• Allow anonymous upload for Vsftpd?

  - by user15318

  I need a basic FTP server on Linux (CentOS 5.5) without any security measure, since the server and the clients are located on a test LAN, not connected to the rest of the network, which itself uses non-routable IP's behind a NAT firewall with no incoming access to FTP. Some people recommend Vsftpd over PureFTPd or ProFTPd. No matter what I try, I can't get it to allow an anonymous user (ie. logging as "ftp" or "anonymous" and typing any string as password) to upload a file: # yum install vsftpd # mkdir /var/ftp/pub/upload # cat vsftpd.conf listen=YES anonymous_enable=YES local_enable=YES write_enable=YES xferlog_file=YES #anonymous users are restricted (chrooted) to anon_root #directory was created by root, hence owned by root.root anon_root=/var/ftp/pub/incoming anon_upload_enable=YES anon_mkdir_write_enable=YES #chroot_local_user=NO #chroot_list_enable=YES #chroot_list_file=/etc/vsftpd.chroot_list chown_uploads=YES When I log on from a client, here's what I get: 500 OOPS: cannot change directory:/var/ftp/pub/incoming I also tried "# chmod 777 /var/ftp/incoming/", but get the same error. Does someone know how to configure Vsftpd with minimum security? Thank you. Edit: SELinux is disabled and here are the file permissions: # cat /etc/sysconfig/selinux SELINUX=disabled SELINUXTYPE=targeted SETLOCALDEFS=0 # sestatus SELinux status: disabled # getenforce Disabled # grep ftp /etc/passwd ftp:x:14:50:FTP User:/var/ftp:/sbin/nologin # ll /var/ drwxr-xr-x 4 root root 4096 Mar 14 10:53 ftp # ll /var/ftp/ drwxrwxrwx 2 ftp ftp 4096 Mar 14 10:53 incoming drwxr-xr-x 3 ftp ftp 4096 Mar 14 11:29 pub Edit: latest vsftpd.conf: listen=YES local_enable=YES write_enable=YES xferlog_file=YES #anonymous users are restricted (chrooted) to anon_root anonymous_enable=YES anon_root=/var/ftp/pub/incoming anon_upload_enable=YES anon_mkdir_write_enable=YES #500 OOPS: bad bool value in config file for: chown_uploads chown_uploads=YES chown_username=ftp Edit: with trailing space removed from "chown_uploads", err 500 is solved, but anonymous still doesn't work: client> ./ftp server Connected to server. 220 (vsFTPd 2.0.5) Name (server:root): ftp 331 Please specify the password. Password: 500 OOPS: cannot change directory:/var/ftp/pub/incoming Login failed. ftp> bye With user "ftp" listed in /etc/passwd with home directory set to "/var/ftp" and access rights to /var/ftp set to "drwxr-xr-x" and /var/ftp/incoming to "drwxrwxrwx"...could it be due to PAM maybe? I don't find any FTP log file in /var/log to investigate. Edit: Here's a working configuration to let ftp/anonymous connect and upload files to /var/ftp: listen=YES anonymous_enable=YES write_enable=YES anon_upload_enable=YES anon_mkdir_write_enable=YES

  Read the article

• Two network adapters on Ubuntu Server 9.10 - Can't have both working at once?

  - by Rob

  I'm trying to set up two network adapters in Ubuntu (server edition) 9.10. One for the public internet, the other a private LAN. During the install, I was asked to pick a primary network adapter (eth0 or eth1). I chose eth0, gave the installer the details listed below in the contents of /etc/network/interfaces, and carried on. I've been using this adapter with these setting for the last few days, and every thing's been fine. Today, I decide it's time to set up the local adapter. I edit the /etc/network/interfaces to add the details for eth1 (see below), and restart networking with sudo /etc/init.d/networking restart. After this, attempting to ping the machine using it's external IP address fails, but I can ping it's local IP address. If I bring eth1 down using sudo ifdown eth1, I can successfully ping the machine via it's external IP address again (but obviously not it's internal IP address). Bringing eth1 back up returns us to the original problem state: external IP not working, internal IP working. Here's my /etc/network/interfaces (I've removed the external IP information, but these settings are unchanged from when it worked) rob@rhea:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary (public) network interface auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx network xxx.xxx.xxx.xxx broadcast xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx # The secondary (private) network interface auto eth1 iface eth1 inet static address 192.168.99.4 netmask 255.255.255.0 network 192.168.99.0 broadcast 192.168.99.255 gateway 192.168.99.254 I then do this: rob@rhea:~$ sudo /etc/init.d/networking restart * Reconfiguring network interfaces... [ OK ] rob@rhea:~$ sudo ifup eth0 ifup: interface eth0 already configured rob@rhea:~$ sudo ifup eth1 ifup: interface eth1 already configured Then, from another machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for [external ip]: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), Back on the Ubuntu server in question: rob@rhea:~$ sudo ifdown eth1 ... and again on the other machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Ping statistics for [external ip]: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms So... what am I doing wrong?

  Read the article

• Configuring OpenLDAP as a Active Directory Proxy

  - by vadensumbra

  We try to set up an Active Directory server for company-wide authentication. Some of the servers that should authenticate against the AD are placed in a DMZ, so we thought of using a LDAP-server as a proxy, so that only 1 server in the DMZ has to connect to the LAN where the AD-server is placed). With some googling it was no problem to configure the slapd (see slapd.conf below) and it seemed to work when using the ldapsearch tool, so we tried to use it in apache2 htaccess to authenticate the user over the LDAP-proxy. And here comes the problem: We found out the username in the AD is stored in the attribute 'sAMAccountName' so we configured it in .htaccess (see below) but the login didn't work. In the syslog we found out that the filter for the ldapsearch was not (like it should be) '(&(objectClass=*)(sAMAccountName=authtest01))' but '(&(objectClass=*)(?=undefined))' which we found out is slapd's way to show that the attribute do not exists or the value is syntactically wrong for this attribute. We thought of a missing schema and found the microsoft.schema (and the .std / .ext ones of it) and tried to include them in the slapd.conf. Which does not work. We found no working schemata so we just picked out the part about the sAMAccountName and build a microsoft.minimal.schema (see below) that we included. Now we get the more precise log in the syslog: Jun 16 13:32:04 breauthsrv01 slapd[21229]: get_ava: illegal value for attributeType sAMAccountName Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SRCH base="ou=oraise,dc=int,dc=oraise,dc=de" scope=2 deref=3 filter="(&(objectClass=\*)(?sAMAccountName=authtest01))" Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SRCH attr=sAMAccountName Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SEARCH RESULT tag=101 err=0 nentries=0 text= Using our Apache htaccess directly with the AD via LDAP works though. Anyone got a working setup? Thanks for any help in advance: slapd.conf: allow bind_v2 include /etc/ldap/schema/core.schema ... include /etc/ldap/schema/microsoft.minimal.schema ... backend ldap database ldap suffix "ou=xxx,dc=int,dc=xxx,dc=de" uri "ldap://80.156.177.161:389" acl-bind bindmethod=simple binddn="CN=authtest01,ou=GPO-Test,ou=xxx,dc=int,dc=xxx,dc=de" credentials=xxxxx .htaccess: AuthBasicProvider ldap AuthType basic AuthName "AuthTest" AuthLDAPURL "ldap://breauthsrv01.xxx.de:389/OU=xxx,DC=int,DC=xxx,DC=de?sAMAccountName?sub" AuthzLDAPAuthoritative On AuthLDAPGroupAttribute member AuthLDAPBindDN CN=authtest02,OU=GPO-Test,OU=xxx,DC=int,DC=xxx,DC=de AuthLDAPBindPassword test123 Require valid-user microsoft.minimal.schema: attributetype ( 1.2.840.113556.1.4.221 NAME 'sAMAccountName' SYNTAX '1.3.6.1.4.1.1466.115.121.1.15' SINGLE-VALUE )

  Read the article

• Virtual Network Interface and NAT disables localhost access for MySQL and Apache

  - by Interarticle

  I'm running an Ubuntu Server 12.04, and recently I configured it to do NAT for my laptop. Since the server has only one NIC, I followed instructions online to create a virtual network device (eth0:0) that has a LAN IP address, then further configured iptables and UFW to allow internet sharing. However, just a few days ago, I discovered that one of the PHP pages hosted on the server failed for no apparent reason. A little digging revealed that the MySQL server started refusing connections from localhost. The same happened with a page (PhpMyAdmin) that was configured to be accessible only from localhost (in Apache2). The error, as shown by $mysql --protocol=tcp -u root -p looks like ERROR 1130 (HY000): Host '<host name of eth0>' is not allowed to connect to this MySQL server However, the funny thing is, I configured the mysql server to allow root access from localhost (only). Moreover, the mysql server listens only on 127.0.0.1:3306, as shown by: sudo netstat -npa | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 1029/mysqld which means that the connection could have only come from 127.0.0.1 (Note that MySQL is working because I can still connect to it via unix domain sockets) In effect, it seems that all tcp connections originating from 127.0.0.1 to 127.0.0.1 appear to any local daemon to come from the eth0 IP address. Indeed, apache2 allowed me to access PhpMyAdmin after I added allow <eth0 IP address>. The following are my network configurations (redacted): /etc/hosts: 127.0.0.1 localhost 211.x.x.x <host name of eth0> <server name> #IPv6 Defaults follows .... /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 211.x.x.x netmask 255.255.255.0 gateway 211.x.x.x dns-nameservers 8.8.8.8 # dns-* options are implemented by the resolvconf package, if installed dns-search xxxxxxx.com hwaddress ether xx:xx:xx:xx:xx:xx auto eth0:0 iface eth0:0 inet static address 192.168.57.254 netmask 255.255.254.0 broadcast 192.168.57.255 network 192.168.57.0 /etc/ufw/sysctl.conf: #Uncommented the following lines net/ipv4/ip_forward=1 net/ipv6/conf/default/forwarding=1 /etc/default/ufw: DEFAULT_FORWARD_POLICY="ACCEPT" #Changed DROP to ACCEPT /etc/init/internet-sharing.conf (upstart script I wrote), section pre-start script: iptables -A FORWARD -o eth0 -i eth0:0 -s 192.168.57.22 -m conntrack --ctstate NEW -j ACCEPT iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE Note again that my problem here is that programs cannot access localhost tcp services, from the server itself, and that access is blocked because the services have access control allowing only 127.0.0.1. I have no problem connecting (as in TCP connections) to services via tcp, even if the services listen only on 127.0.0.1. I do NOT want to connect to the services from another computer.

  Read the article

• Passive FTP on Windows Server 2008 R2 using the IIS7 FTP-Server

  - by ntor

  Hello serverFault-community! During the last few days I have been setting up a Windows Server 2008 R2 in a VMware. I installed the standard FTP-Server on it by using the Webserver (IIS)-role. Everything works fine with accessing my FTP-Site with ftp://localhost in Firefox. I can also get access to it via the local IP of my Server. Actually everything works fine in my LAN. But here's my problem: I want to get access "from outside", using the external IP or a dyndns-URL. I have a LinkSys-Router in front of my Server, therefore I'm forwarding all the important ports. If you may now think "this idiot has probably forgotten some ports", I must dissappoint you. It even works getting access to my Server-Website and messing around in some WebInterfaces. The problem is my passive FTP (active works for me). I always get a timeout, when e.g. FileZilla waits for a response to the LIST-command. The one big thing I don't get, is, why my Server sends a response to the PASV-command, naming a port like 40918, even if I have restricted the data port range for my passive FTP ( in the IIS-Manager) to e.g. [5000-5009]. I simply don't want to open and forward all possible data ports! And another thing is, I can't specify a static external IP-adress for my server, since I don't own any. I hope I have explained my problem in a comprehensible way. If not, simply ask by posting a comment! LG ntor PS: I have already mainly tried following articles: Out Of Band FTP 7 shows "Operation timed out" How to Configure Windows Firewall for a Passive Mode FTP Server ServerFault --- Passive ftp on Server 2008 --- EDIT: --- There is one idea rising up in my mind: When I use FileZilla to connect by passive mode I always get something like this: 227 Entering Passive Mode (192,168,1,102,160,86) According to a Rhinosof-article FZ tries to connect on port "160*256+86 = 41046", although I have restricted the data ports (as mentioned above). Could this be caused by the router, that doesn't forward out-ports directly, but uses different ones? (-- The IP-Adress given is the local one, since I'm not able to define a static external in the IIS-Mgr)

  Read the article

• Eclipselink read complex object model in an ordered way

  - by Raven

  Hi, I need to read a complex model in an ordered way with eclipselink. The order is mandantory because it is a huge database and I want to have an output of a small portion of the database in a jface tableview. Trying to reorder it in the loading/quering thread takes too long and ordering it in the LabelProvider blocks the UI thread too much time, so I thought if Eclipselink could be used that way, that the database will order it, it might give me the performance I need. Unfortunately the object model can not be changed :-( The model is something like: @SuppressWarnings("serial") @Entity public class Thing implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; private String name; @OneToMany(cascade=CascadeType.ALL) @PrivateOwned private List<Property> properties = new ArrayList<Property>(); ... // getter and setter following here } public class Property implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; @OneToOne private Item item; private String value; ... // getter and setter following here } public class Item implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; private String name; .... // getter and setter following here } // Code end In the table view the y-axis is more or less created with the query Query q = em.createQuery("SELECT m FROM Thing m ORDER BY m.name ASC"); using the "name" attribute from the Thing objects as label. In the table view the x-axis is more or less created with the query Query q = em.createQuery("SELECT m FROM Item m ORDER BY m.name ASC"); using the "name" attribute from the Item objects as label. Each cell has the value Things.getProperties().get[x].getValue() Unfortunately the list "properties" is not ordered, so the combination of cell value and x-axis column number (x) is not necessarily correct. Therefore I need to order the list "properties" in the same way as I ordered the labeling of the x-axis. And exactly this is the thing I dont know how it is done. So querying for the Thing objects should return the list "properties" "ORDER BY name ASC" but of the "Item"s objects. My ideas are something like having a query with two JOINs. Joing Things with Property and with Item but somehow I was unable to get it to work yet. Thank you for your help and your ideas to solve this riddle.

  Read the article

• Why is my router not routing?

  - by dwj

  Starting a week and half ago my router stopped working with my cable modem. I went to sleep with it working and woke up with it not. I swapped in another router and am still having issues; I was gone for 10 days so now I'm back to trying to figure it out. While I was gone I left everything (cable modem, router, and computer) powered off. My setup: Comcast Ambit cable modem (from Comcast) Netgear WGR614 v4 router -- replaced with Linksys WRT54GS v1.1 Windows XP SP3 other computers, all currently unplugged The modem is using the firmware (ver 2.105.2001) provided by Comcast; hardware version 1.3 The Linksys router is using FW ver 4.71.4 (latest for this release of HW), factory defaults I am only using the wired connections; no wireless. I have swapped out all of the cat5 cable. If I plug my computer directly into the cable modem, I can ping by name or number. Everything works perfectly. If I plug my computer into the router and the router into the modem, I cannot access anything outside of my local network. This is the exact setup I've used for the past 5 years; there were no changes in the past year. Now here's the interesting part: I can log into the Linksys router and get status information from it; everything appears good. Using the Diagnostics, I can run ping and traceroute to any site on the internet. These work perfectly. From my computer, I can ping the router and the modem. However, I cannot ping anything on the internet by with name or number. If I plug in another computer, I can ping it successfully. I've included two transcripts below that show these two attempts. Addresses, DNS, gateways, etc. look good. I cannot access the internet through either router. I am at a loss here. Suggestions? Help! Computer to Router to Cable Modem C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:21:55 PM Lease Expires . . . . . . . . . . : Tuesday, March 23, 2010 10:21:55 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Ping request could not find host google.com. Please check the name and try again . C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\ Computer to Cable Modem Directly C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 DHCP Server . . . . . . . . . . . : 68.87.76.10 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:18:50 PM Lease Expires . . . . . . . . . . : Monday, March 22, 2010 11:12:31 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Pinging google.com [74.125.19.99] with 32 bytes of data: Reply from 74.125.19.99: bytes=32 time=20ms TTL=55 Reply from 74.125.19.99: bytes=32 time=17ms TTL=55 Reply from 74.125.19.99: bytes=32 time=28ms TTL=55 Reply from 74.125.19.99: bytes=32 time=18ms TTL=55 Ping statistics for 74.125.19.99: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 17ms, Maximum = 28ms, Average = 20ms C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=17ms TTL=55 Reply from 74.125.19.104: bytes=32 time=16ms TTL=55 Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 16ms, Maximum = 18ms, Average = 17ms C:\

  Read the article

• How can I connect DLNA devices through NAT?

  - by Bob

  I have a Windows 7 PC running Serviio as a DLNA server. I have a Samsung I9100G running Skifta as a DLNA renderer (client). My network topology: At the moment, I can connect and watch my videos fine if the phone is on router #2. The server is on a wired network with #2. Router #1 is 192.168.1.1, router #2 is 192.168.2.1 (192.168.1.2) and router #3 is 192.168.3.1 (192.168.1.3). In other words, each router has its own subnet, using NAT - their "modem" port is connected with a "LAN" port on the modem/router 1. What I want to do is be able to connect to the DLNA server if the renderer is connected to router #1/#3 - #1 is on the WAN side of #2, while #3 is even further separated. I'll settle for just #1 working, though. Normally, I would just forward the appropriate ports, and everything would work fine. However, (apparently) DLNA uses UPnP, which I am unfamiliar with. I tried enabling UPnP on router #2, but that did not seem not change anything. It's a Belkin F5D7230-4 6000 - there's reported issues with UPnP on F5D7230-4 7000. UPnP is already enabled on router #1 - a Billion BiPAC 7700N. I've also tried the built in DLNA renderer/server/controller on my phone, Samsung AllShare. It can see the server on router #2 and browse files, but has issues playing or downloading them. It also can't see the server on the other two networks. I'm currently using Skifta/s "local" mode. "Remote" mode requires an account, which I don't really want to create if not necessary. Is it possible too do what I'm trying to do? If no, are there workarounds? If yes, how do I do it? Is my server the issue? The renderer (client)? The router(s)? My method? I can change just about anything except the routers.

  Read the article

• Please Explain Drupal schema and drupal_write_record

  - by Aaron

  Hi. A few questions. 1) Where is the best place to populate a new database table when a module is first installed, enabled? I need to go and get some data from an external source and want to do it transparently when the user installs/enables my custom module. I create the schema in {mymodule}_schema(), do drupal_install_schema({tablename}); in hook_install. Then I try to populate the table in hook_enable using drupal_write_record. I confirmed the table was created, I get no errors when hook_enable executes, but when I query the new table, I get no rows back--it's empty. Here's one variation of the code I've tried: /** * Implementation of hook_schema() */ function ncbi_subsites_schema() { // we know it's MYSQL, so no need to check $schema['ncbi_subsites_sites'] = array( 'description' => 'The base table for subsites', 'fields' => array( 'site_id' => array( 'description' => 'Primary id for site', 'type' => 'serial', 'unsigned' => TRUE, 'not null' => TRUE, ), // end site_id 'title' => array( 'description' => 'The title of the subsite', 'type' => 'varchar', 'length' => 255, 'not null' => TRUE, 'default' => '', ), //end title field 'url' => array( 'description' => 'The URL of the subsite in Production', 'type' => 'varchar', 'length' => 255, 'default' => '', ), //end url field ), //end fields 'unique keys' => array( 'site_id'=> array('site_id'), 'title' => array('title'), ), //end unique keys 'primary_key' => array('site_id'), ); // end schema return $schema; } Here's hook_install: function ncbi_subsites_install() { drupal_install_schema('ncbi_subsites'); } Here's hook_enable: function ncbi_subsites_enable() { drupal_get_schema('ncbi_subsites_site'); // my helper function to get data for table (not shown) $subsites = ncbi_subsites_get_subsites(); foreach( $subsites as $name=>$attrs ) { $record = new stdClass(); $record->title = $name; $record->url = $attrs['homepage']; drupal_write_record( 'ncbi_subsites_sites', $record ); } } Can someone tell me what I'm missing?

  Read the article

• How do I protect a low budget network from rogue DHCP servers?

  - by Kenned

  I am helping a friend manage a shared internet connection in an apartment buildling with 80 apartments - 8 stairways with 10 apartments in each. The network is laid out with the internet router at one end of the building, connected to a cheap non-managed 16 port switch in the first stairway where the first 10 apartments are also connected. One port is connected to another 16 port cheapo switch in the next stairway, where those 10 apartments are connected, and so forth. Sort of a daisy chain of switches, with 10 apartments as spokes on each "daisy". The building is a U-shape, approximately 50 x 50 meters, 20 meters high - so from the router to the farthest apartment it’s probably around 200 meters including up-and-down stairways. We have a fair bit of problems with people hooking up wifi-routers the wrong way, creating rogue DHCP servers which interrupt large groups of the users and we wish to solve this problem by making the network smarter (instead of doing a physical unplugging binary search). With my limited networking skills, I see two ways - DHCP-snooping or splitting the entire network into separate VLANS for each apartment. Separate VLANS gives each apartment their own private connection to the router, while DHCP snooping will still allow LAN gaming and file sharing. Will DHCP snooping work with this kind of network topology, or does that rely on the network being in a proper hub-and-spoke-configuration? I am not sure if there are different levels of DHCP snooping - say like expensive Cisco switches will do anything, but inexpensive ones like TP-Link, D-Link or Netgear will only do it in certain topologies? And will basic VLAN support be good enough for this topology? I guess even cheap managed switches can tag traffic from each port with it’s own VLAN tag, but when the next switch in the daisy chain receives the packet on it’s “downlink” port, wouldn’t it strip or replace the VLAN tag with it’s own trunk-tag (or whatever the name is for the backbone traffic). Money is tight, and I don’t think we can afford professional grade Cisco (I have been campaigning for this for years), so I’d love some advice on which solution has the best support on low-end network equipment and if there are some specific models that are recommended? For instance low-end HP switches or even budget brands like TP-Link, D-Link etc. If I have overlooked another way to solve this problem it is due to my lack of knowledge. :)

  Read the article

• Issue with VMWare vSphere and NFS: re occurring apd state

  - by Bastian N.

  I am experiencing issues with VMWare vSphere 5.1 and NFS storage on 2 different setups, which result in an "All Path Down" state for the NFS shares. This first happened once or twice a day, but lately it occurs much more frequent, as specially when Acronis Backup jobs are running. Setup 1 (Production): 2 ESXi 5.1 hosts (Essentials Plus) + OpenFiler with NFS as storage Setup 2 (Lab): 1 ESXi 5.1 host + Ubuntu 12.04 LTS with NFS as storage Here is an example from the vmkernel.log: 2013-05-28T08:07:33.479Z cpu0:2054)StorageApdHandler: 248: APD Timer started for ident [987c2dd0-02658e1e] 2013-05-28T08:07:33.479Z cpu0:2054)StorageApdHandler: 395: Device or filesystem with identifier [987c2dd0-02658e1e] has entered the All Paths Down state. 2013-05-28T08:07:33.479Z cpu0:2054)StorageApdHandler: 846: APD Start for ident [987c2dd0-02658e1e]! 2013-05-28T08:07:37.485Z cpu0:2052)NFSLock: 610: Stop accessing fd 0x410007e4cf28 3 2013-05-28T08:07:37.485Z cpu0:2052)NFSLock: 610: Stop accessing fd 0x410007e4d0e8 3 2013-05-28T08:07:41.280Z cpu1:2049)StorageApdHandler: 277: APD Timer killed for ident [987c2dd0-02658e1e] 2013-05-28T08:07:41.280Z cpu1:2049)StorageApdHandler: 402: Device or filesystem with identifier [987c2dd0-02658e1e] has exited the All Paths Down state. 2013-05-28T08:07:41.281Z cpu1:2049)StorageApdHandler: 902: APD Exit for ident [987c2dd0-02658e1e]! 2013-05-28T08:07:52.300Z cpu1:3679)NFSLock: 570: Start accessing fd 0x410007e4d0e8 again 2013-05-28T08:07:52.300Z cpu1:3679)NFSLock: 570: Start accessing fd 0x410007e4cf28 again As long as the issue occurred once or twice a day it really wasn't a problem, but now this issue has impact on the VMs. The VMs get slow or even hang, resulting in a reset through vCenter in the production environment. I searched the web extensively and asked in forums, but till now nobody was able to help me. Based on blog posts and VMWare KB articles I tried the following NFS settings: Net.TcpipHeapSize = 32 Net.TcpipHeapMax = 128 NFS.HartbeatFrequency = 12 NFS.HartbeatMaxFailures = 10 NFS.HartbeatTimeout = 5 NFS.MaxQueueDepth = 64 Instead of NFS.MaxQueueDepth = 64 I already tried other settings like NFS.MaxQueueDepth = 32 or even NFS.MaxQueueDepth = 1. Unfortunately without any luck. It would be great if someone could help me on this issue. It is really annoying. Thanks in advance for all the help. [UPDATE] As I explained in the comment below, here is the network setup: On the production setup the NFS traffic is bound to a separate VLAN with ID 20. I am using a HP 1810 24 Port Switch. The OpenFiler system is connected to the VLAN with 4 Intel GbE NICs with dynamic LACP. The ESXis both have 4 Intel GbE NICs using 2 static LACP trunks containing 2 NICs each. One pair is connected to the regular LAN and the other one to the VLAN 20. And here is a screenshot of the vSwitch: Switch configuration: Port configuration: On the lab setup its a single Intel NIC on each side without VLAN, but with different IP subnet.

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• How to grow to be global sysadmin of an organization?

  - by user64729

  Bit of a non-technical question but I have seen questions of the career development type on here before so hopefully it is fine. I work for a fast growing but still small organization (~65 employees). I have been their external sysadmin for a while now, looking after hosted Linux servers and infrastructure. In the past 12 months I have been transforming into the internal sysadmin for our office too. I'm currently studying Cisco CCNA to cover the demands of being an internal sysadmin and looking after the office LAN, routers, switches and VPNs. Now they want me to look after the global sysadmin function of the organization as a whole. The organization has 3 offices in total, 2 in the UK and 1 in the US. I work in one of the UK offices. The other offices are primarily Windows desktops with AD domain shops. My office is primarily a Linux shop with a file-server and NFS/NIS (no AD domain for the Windows desktops yet but it's in the works). Each other office has a sysadmin which in theory I am supposed to supervise but in reality each is independent. I have a very competent junior sysadmin working with me who shares the day-to-day tasks and does some of the longer term projects with my supervision. My boss has asked me how to grow from being the external sysadmin to the global sysadmin. I am to ponder this and then report back to him on how to achieve this. My current thoughts are: Management training or professional development - eg. reading books such as "Influencer" and "7 Habits". Also I feel I should take steps to improving communication skills since a senior person is expected to talk and speak out more often. Learn more about Windows and Active Directory - I'm an LPI-certified guy and have a lot of experience in Linux (Ubuntu or desktop, Debian/Ubuntu as server). Since the other offices are mainly Windows-domains it makes sense to skill-up in that area so I can understand what the other admins are talking about. Talk to previous colleagues who have are are in this role already - to try and get the benefit of their experience. Produce an "IT Roadmap" or similar that maps out where we want the organization to be and when, plotted out over the next couple of years with regards to internal and external infrastructure. I have produced a "Security roadmap" already which does cover some of these things. I guess this can summed up as "thinking more strategically"? I'd appreciate comments from anyone who has been through a similar situation, thanks.

  Read the article

• configure squid3 to set up a web proxy in ubuntu12.04

  - by Gnijuohz

  I am in a LAN and have to use a proxy given to access the web in a very limited way. I can't even use google, github.com or SE sites. However I can use ssh to log into a server, which I have root access so basically I can do anything I want with it. So I was thinking that maybe I could use that server as a proxy so I can visit sites through it. I tested it using ssh -vT [email protected] which gave a proper response. And In my computer I can't do this. Also I tried downloading something from the gun.org using wget, which can't be done in my computer too. And it succeeded on that server. I don't know if that's enough to say that this server have full access to the Internet. But I assumed so and I installed squid3 on it. After trying some while, I failed to get it working. I got this after I run squid3 -k parse 2012/07/06 21:45:18| Processing Configuration File: /etc/squid3/squid.conf (depth 0) 2012/07/06 21:45:18| Processing: acl manager proto cache_object 2012/07/06 21:45:18| Processing: acl localhost src 127.0.0.1/32 ::1 2012/07/06 21:45:18| Processing: acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 2012/07/06 21:45:18| Processing: acl localnet src 10.1.0.0/16 # RFC1918 possible internal network 2012/07/06 21:45:18| Processing: acl SSL_ports port 443 2012/07/06 21:45:18| Processing: acl Safe_ports port 80 # http 2012/07/06 21:45:18| Processing: acl Safe_ports port 21 # ftp 2012/07/06 21:45:18| Processing: acl Safe_ports port 443 # https 2012/07/06 21:45:18| Processing: acl Safe_ports port 70 # gopher 2012/07/06 21:45:18| Processing: acl Safe_ports port 210 # wais 2012/07/06 21:45:18| Processing: acl Safe_ports port 1025-65535 # unregistered ports 2012/07/06 21:45:18| Processing: acl Safe_ports port 280 # http-mgmt 2012/07/06 21:45:18| Processing: acl Safe_ports port 488 # gss-http 2012/07/06 21:45:18| Processing: acl Safe_ports port 591 # filemaker 2012/07/06 21:45:18| Processing: acl Safe_ports port 777 # multiling http 2012/07/06 21:45:18| Processing: acl CONNECT method CONNECT 2012/07/06 21:45:18| Processing: http_port 3128 transparent vhost vport 2012/07/06 21:45:18| Starting Authentication on port [::]:3128 2012/07/06 21:45:18| Disabling Authentication on port [::]:3128 (interception enabled) 2012/07/06 21:45:18| Disabling IPv6 on port [::]:3128 (interception enabled) 2012/07/06 21:45:18| Processing: cache_mem 1000 MB 2012/07/06 21:45:18| Processing: cache_swap_low 90 2012/07/06 21:45:18| Processing: coredump_dir /var/spool/squid3 2012/07/06 21:45:18| Processing: refresh_pattern ^ftp: 1440 20% 10080 2012/07/06 21:45:18| Processing: refresh_pattern ^gopher: 1440 0% 1440 2012/07/06 21:45:18| Processing: refresh_pattern -i (/cgi-bin/|?) 0 0% 0 2012/07/06 21:45:18| Processing: refresh_pattern (Release|Packages(.gz)*)$ 0 20% 2880 2012/07/06 21:45:18| Processing: refresh_pattern . 0 20% 4320 2012/07/06 21:45:18| Processing: ipcache_high 95 2012/07/06 21:45:18| Processing: http_access allow all I deleted some allow and deny rules and added http_access allow all so that all the request would be allowed. After configuring my computer, I got this error: Access control configuration prevents your request from being allowed at this time. Please contact your service provider if you feel this is incorrect. And the log in the server showed that my TCP requests had all been denied. So, first of all, is what I am trying to do achievable? If so, how to configure the squid in the server so that I use it as a proxy to surf the Internet? My computer and the server both run Ubuntu11.04. Thanks for any help~

  Read the article

• Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem

  - by zchads

  Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem. Hardware Information: Buffalo Wireless Router/access point, Model: WZR-HP-G300NH-AP DSL Modem: Generic (actually not sure of manufacture). Service Provider: TOT (Thailand) Laptop-1: Windows XP and Belkin PCMIA Network Card Laptop-2: Windows XP unknown network card & Wifi Laptop-3: Windows 7 unknown network card & Wifi Outline of Problem/actions taken: After a recent power failure the router and laptop-1 connected to router were no longer able to access the internet. Actions taken to try and recover internet access: Using Laptop-1 tried to configure Router with PPPoe settings using software from Router Manufacture. During the installation process a Timeout error was experienced, unable to connect to WAN. Used Internet Explorer to communicate directly with Router using IP address. Changed settings to use PPPoe settings given by ISP. Router was not able to communicate with Internet. Repeated steps 1-4 again with no success. Reset Router and DSL modem. Repeated steps 1-4 again still no success. Tried connecting Laptop-1 directly to DSL to gain access to internet to research problem. No Network connection with DSL could be established…connection would be established for a second and then be lost and didn’t appear long enough to actually connect to DSL. Replugged LAN back into Router and connection was regained with laptop-1. Replugged Laptop-1 directly into DSL and again unable to establish network connection. Uninstalled network card and all of its drivers on Laptop-1. Reinstalled network card and drivers and tried connecting directly to DSL. Still unable to make network connection. Plugged DSL into Laptop-3 and Internet connection was established. Being Laptop-3 does not have a CD-Rom, Laptop-2 was tried to connect to the router. With Laptop-2 steps 1-7 ended up being repeated without success. Tried plugging Laptop-2 directly into DSL and again no network connection could be established. Using Laptop-3 with a direct connection to DSL downloaded latest Router FW. Installed router FW using Laptop-1. Tired the installation process again without success. Being desperate reinstalled OS on Laptop-1 still not success. Tried using “ipconfig” with router to see what was going on without success. With laptop-1 connected to DSL went through the “ipconfig /…” inputs to see if anything made a difference. Being the network card was not able to make a connection this provide very little information “media disconnected”. So now I have a router and two laptops which are unable to connect to the internet and sure could use some advice/help.

  Read the article

< Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >