Search Results

Search found 18594 results on 744 pages for 'computer science student'.

Page 166/744 | < Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >

  • Microsoft mouse screws up my power settings

    - by Patriot
    Running a new computer with Windows 7 and 64-bit OS. Had a wireless Logitech mouse that worked perfectly with this set up. The mouse was old, and the buttons were sticking and causing double clicks, so I bought a new Microsoft Mobile Wireless 3000 mouse to replace it. The new mouse works perfectly, but now my screen saver is disabled and my computer won't go into sleep mode after 15 minutes as per my power setting. If I hook the Logitech mouse back up, screen saver works fine and computer goes to sleep as it should. Am I missing something, or is Microsoft's mouse just junk. Got no software with the new mouse, so no drivers seem available.

    Read the article

  • Network tries to reindentify itself now and then

    - by Don Young
    When the computer starts up it connects itself to the router (ZTE 4G router) automatically, but after I have surfed the web for a while, it tries to identify itself, meaning you get that little blue circle next to the little screen at the corner. When browsing it does not cause any problems, but if I'm streaming a video the video will then stop, I'll have to refresh the page to make the video start again. And if I'm playing a game, LoL for example, the game will freeze for about 2 seconds then continue again (due to lost connection to the internet). I have no virus on my computer, although I had before. I have reset my router, restarted my computer, updated my ethernet driver, checked so that the IPv4 is set on automatic and tried different router channels. I have had this router for a few months and the problem just started recently. Here is the ipconfig screen:

    Read the article

  • Command line, determine 64 or 32 bit?

    - by svnpenn
    I need to reinstall Windows on a laptop. I have the product key (its on the laptop), and I know it is Windows 7 Home Premium. I need a way to determine if 64-bit or 32-bit Windows is installed, so that I can download the correct one from Microsoft. The computer is messed up so I do not have access to Windows to check it with systeminfo. I took out the hard drive and hooked it to another computer, but when I run systeminfo it just gives information for the host computer, I did not see a way to change this.

    Read the article

  • Win8 x64 Laptop (Samsung) unable to boot after installing Ubuntu

    - by user285872
    I posted here a while back and no one was able to help me so I am going to try to explain my problem better. I have a Samsung series 7 Ultrabook and I connected a USB optical drive with an Ubuntu 14.04 installation disc. I did not set or change any of my partitions, however, as I mainly wanted to just be able to boot from the disc and fool around with Ubuntu. Upon restarting my computer I get a blue-screen message saying: Recovery Your PC needs to be repiared The Boot configuration date file is missing some required information. File: \BCD Error Code: 0xc000000d You'll need to use the recovery tools on your installing media. If you don't have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. However I am never given the option to even try to boot to anything. When I turn my computer on the optical drive spins and then after a moment or two comes to a halt. I turned off safeboot and switched it to CSM (I believe that is what it is called) mode, and that makes it so when I turn my computer on it takes me to a Windows Recovery screen. I am able to change the date I want to recover and view all the applications installed, however upon recovering Windows says "All boot options are tried. Press key to recover with factory image using Recovery or any other keys for next boot loop iteration." It seems to be stuck in a loop. Can someone please help me?! I'm so confused and nothing is working!

    Read the article

  • Ubuntu 12.04 (dual boot with Windows 7), doesn't boot after I deleted some files from Windows. What can I do?

    - by sacha
    The Ubuntu 12.04 I have installed (in Dual-Boot with Windows 7) using WUBI worked perfectly for over a month. Then it informed me that I ran out of space on the hard drive and I assumed it was because my hard drive on Windows was full. I logged into Windows and deleted the whole New Volume D. But now the problem is that it is not possible to log into Ubuntu but in Windows it's possible. I really paid attention about not deleting important files in Windows. When i try to log into Ubuntu : _either it does not go far and i have to restart the computer _or it goes until the loading time and a message says something like "[...] Graphics could not be detected [...]" and they ask to choose between 4 options including "Start with poor Graphics", "Reconfigure Graphics", "Troubleshoot" and "Restart the computer". But none of the options run and i also have to restart the computer manually from that point I have plenty of useful files in Ubuntu so i want to find another way to solve the problem instead of Uninstall/Reinstall Ubuntu. I want to know what happened ? And how to make it work ?

    Read the article

  • Which one to select for my future career; Java, C#, Azure or Apex?

    - by user636195
    Hi folks, This time, I am going to studying Masters in Computer Science in U.S.A after a week. I have been doing my B.Sc for the past three years and after my freshman year I started working on projects (in C# and very rarely in Java) for the past two years.(i.e while I was a second and third year student). Now I am in a college where all of the programming courses are going to be taken in Java only (using Eclipse) and I am going to stay in this college for 8 months on campus and then fully employed for two years in other companies as a CPT. I really love to work on Microsoft products because, for me, they are simple and easy to use and understand. My future plan is to work in Cloud computing and be a Cloud based business owner in the near future. Since the college is going to teach us and let us do every project in Java, I was confused which programming language to use that will help me and enhance me in my career, and of course I wanted to select the one I liked to do everytime. I also heard a lot about Azure (Microsoft’s ) and Apex (Salesforce.com’s cloud computing programming language). Would you please give me your advice and recommendation based on my situation? Should I have to study only Java, or should I have to study C# or Azure beside Java on my own? The reason I asked this is because, since I have no clue how Azure works and how long it will take me to know the language, I am really confused which one to select (Java Vs C# and Azure Vs Apex or if there is any popular and mostly used Cloud Computing langauge). Do you think I can get a job in cloud computing if I study Azure or Apex by my own without experience? There is also one issue I want to consider which is a short term issue is. i.e Salary. Since I have to pay my student loan, I also need to get a good job which will let me pay my loan within two years. But, as I said, my long term plan is, get experience in Cloud Computing (from programming to administrative part,i.e every area of cloud computing) and then have my own business may be within 5-10 years. What do you think? Thank you for your time.

    Read the article

  • certificate program on database management [closed]

    - by gcc
    I am third year computer engineer student. I want take certificate at database management. However, In my country, there is no available course. Where can I learn any certificate program which is available via Internet ? Can you recommend me any program with one-two sentence to explain why I should participate in ? Note : exam should be online course & book should be available via Internet

    Read the article

  • What's a good way to get an IT internship? [closed]

    - by user1419715
    I'm a second year CS student who's worked really hard to build and expand my skills. I've spent the past week now trying to find a place to volunteer (i.e. work for FREE) so I can get a little bit of in-the-door experience with web development. I have a portfolio with several decent projects, a handful of languages and other hard/soft skills that employers constantly say they're clamoring for. I can't even get people to take my calls. This is me offering to work for them for FREE, remember. I'm in a reputable program at a respected school, get decent grades and...yeah, I've worked really hard to be presentable. On the rare occassions I actually get to speak to somebody at a design firm they hedge and do everything they can to get me off the phone. Nobody's ever expressed even the slightest interest in taking me on. The answer to the experience problem is supposed to be "you need to spend a year or two building up a big portfolio of projects on your own" so that employers will be impressed. I've done that. Websites, standalone apps, etc.. Nobody will even look at my resume, though. Question: Why does there seem to be so little interest in taking on upaid interns in the world of IT? Update: Sorry you all think I'm too aggressive or angry. It wasn't my intent to be a jerk to people while asking them for their opinions. That said, how would you feel if employer after employer turned you down cold when you offered yourself to them without asking for remuneration? One can't even get an unpaid job in this economy now, it seems. How am I going about my search? I find web firms in my area and contact them via email with a brief sales pitch of myself and a resume attached. Then a couple of days later I follow up with a phone contact. Nobody--anywhere--is advertising for interns of any kind. If there were I'm sure there'd be about 500 resumes per position, even unpaid. I've had good experiences in the past with cold-calling firms for actual paid jobs in other industries (hiring is a pain in the ass process and a call like this can show initiative while reducing a busy employer's need to do all the hiring overhead work), so I thought volunteering would work at least as well. My skills are pretty good for a CS student and include the usual suspects: HTML/CSS/Javascript, Python, Java, C, C#/.Net etc etc. I made a point on my resume to tie each ability claim to a project as well. Oh, and regarding the "working for free still costs the employer money" argument: that's an excellent point I hadn't though of. But it means...what? I have to pay the employer for the privilege of working there now?

    Read the article

  • Does programmable hardware exist to allow hardware to be programmed by computers?

    - by agentbanks217
    I am a programmer and I have never really dealt with the hardware of anything, only software. I want to start building things that I can control from my computer using programming. My question is are there such devices on the market that have a programmable interface or API? For example, I want to build a automated window blinds opening/closing device, and I would like to be able to control it from my computer e.g. writing an app or some code to schedule them when to open and close. I would like to know if there are any devices that can be programmed to do that (the computer part)? Thanks!

    Read the article

  • The Ashpocalypse

    Melange is the open source web app that runs Google Summer of Code ™ each year. It is being developed and maintained by a volunteer team of student...

    Read the article

  • Copy/Pasting data from SQL Server to Excel splits up text into multiple columns?

    - by Paul
    I've got a problem pasting data from the result grid of SQL Server 2005 to an excel 2007 spreadsheet. I have a query in SQL Server that returns 2 columns (a number column and a text column) On one computer here i can happily copy (right-click copy) and then just right-click and paste into an excel spreadsheet. no problem. On another computer here when i try and paste into excel it splits the text column up and pastes the text into multiple columns based on spaces between words. For example if one of the rows has... Paste me please ...in it then when pasting into excel it splits the text and pastes each work into a seperate column within excel. We've tried comparing options in both SQL Server & excel with the computer it works fine on but can see no differences. Any ideas welcome Thanks

    Read the article

  • RDC not working from outside

    - by Cotten
    I've set up Remote Connection according to : http://windows.microsoft.com/is-IS/windows7/allow-remote-desktop-connections-from-outside-your-home-network That is, Allow remote connections to the computer you want to access. Make sure Remote Desktop is able to communicate through your firewall. Find the IP address of the computer on your home network that you want to connect to. Open your router's configuration screen and forward TCP port 3389 to the destination computer's IP address. Find your router's public IP address so that Remote Desktop can find it on the Internet. When I'm inside the LAN, RDC works flawlessly. When I try to connect to the ip given by my ISP it cannot connect. I've setup port forwarding for 3389 on my netgear router. Thanks!

    Read the article

  • Motherboard not recognizing memory anymore

    - by root
    I bought some new RAM and installed it on my motherboard. But, the BIOS would not post. There's an LED on my motherboard that shows error codes, and it showed the error: No usable memory detected. So, I removed the new memory and reinstalled the old memory, thus restoring the computer back to its original configuration. But, the BIOS still would not post, still giving the error: No usable memory detected. I've ensured that the memory and power headers are seated properly. I've tried all possible combinations of memory slots, and I've also reset the CMOS, but the error remains the same. The computer was working fine before I tried upgrading the memory, and I originally assembled the computer myself. What are some possible causes of this problem?

    Read the article

  • two shops network

    - by edward
    okay so, I just opened up two shops in my hometown. The two stores is about 6 blocks apart, connecting them by wire is not really feasible in cost wise. What kind of network topology should I use for my small shops, there will be 5 computers, one is the sales computer ,another 4 as mentioned is the guest computer. I want the sales and guest computers network to be seperated. Both shops have same computers. The guest computers serves up simple website that has my shop catalog on it, I'm thinking of using a web server. So, how am i suppose to setup these networks, im planning to add in more computers in the future. Is it I need to station a single server at a shop, and all the computer connected to it? or is there any more effective methods? I'm no networking expert, would love to hear some advice.

    Read the article

  • Pc not booting, no video output, hard drive noises

    - by bullettime
    My computer suddenly stopped booting up. I just came back from a week long trip, and it was working fine before I left. When I power up the computer now, it seems to power up just fine (leds on, fans working), but then there's no output on the screen at all, and there's a noise that seems to be coming from the HD, like it is trying to read something. After the noise starts, it does 6 cycles and then stops. I'm not sure but I don't think it did this noise when the pc was still working. I tried using the onboard video card instead but it made no difference. What could be wrong with my computer?

    Read the article

  • I would like to pipe output of find into input list of scp, how?

    - by user13184
    I'm a novice linux user and I am trying to send a long list of files from one computer to another. The argument list is too long, so I am using find. I am having trouble setting up the expression, though. Can someone help? Here is what I would normally type for a short argument list. scp ./* phogan@computer/directory... Here's I think this might translate into with find. scp find . -name "*" phogan@computer/directory... Maybe I could use piping? Any suggestions would help. Thanks in advance.

    Read the article

  • ubuntu 13.10 liveboot/installer loads dots, then does nothing

    - by user200245
    Problem: When I load an Ubuntu 13.10 (64-bit) live USB / installer on my laptop, the purple Ubuntu screen with the white dots appears, the dots turn orange (indicating its loading), then after a few seconds the screen turns completely black and nothing else happens. I can not install Ubuntu 13.10 on this computer. What I've Tried: I've re-downloaded the .iso file from canonical. I've burned the .iso to the USB using the default linux usb image writer, and the Windows programs YUMI and Linux Live USB Creator; same thing happens each time. Yes, I'm sure my computer is 64 bit. I'm currently running Linux Mint 15 on it, which runs perfectly. It's a Sager NP7330 / Clevo w230st. extra info A few months I installed Ubuntu 13.04 on this machine, which installed perfectly. Normally I'd install that then dist-upgrade to 13.10, HOWEVER this computer is only a few months old and the wireless/network drivers for my network card were not implemented until kernel 3.11 (which comes w ith 13.10). I tried manually downloading kernel 3.11 and installing it (on 13.04), however the wireless card nor ethernet card still did work with Ubuntu 13.04. So my only real hope is to get 13.10 working. Does anyone know what's up with this?

    Read the article

  • What can cause a black or blank screen when pressing logout or switch user in windows 7

    - by Medran
    The situation I have here is related to a brand new dell machine with a GTX260 video card. Put simply after one user logs in when that user either 'switch users' or 'logs out' windows goes to a black/blank screen. The TV screen that is used with this computer previously functioned fine with fast user switching on an XP machine. The new computer is windows 7. The TV is not outputting any error messages like 'no signal' or anything else that would be displayed if the computer was off. You can fix the problem by cycling the input on television, after cycling the input the welcome screen appears as normal. What I want to know is what on earth is windows doing that would cause the video card to stop sending the same signal to the monitor when the user logs off or switches users. I mean as far as I can tell the resolution is identical between windows and the welcome screen. Or perhaps if somebody has experienced this before a fix would be great too.

    Read the article

  • Do I really need to reboot for AD changes to be applied?

    - by stimms
    Every time I request a permission change the IT group at my company instructs me to wait 20 minutes and reboot the computer. I cannot believe that in this day and age you still need to reboot the computer to clear whatever cache stores the permissions locally. It feels like something out of the NT 4 days. Do you actually still need to reboot the computer? Is a logout/login sufficient? Is there still a long time(20 minutes) for the changes to propagate through the AD tree?

    Read the article

  • MS 2008 R2 Drops Remote Desktop Sessions in 10 seconds or less every time

    - by mike42
    I'm adding a new 64-bit server to our domain. Everything seems fine except when accessing the machine using remote desktop, after a few seconds the connection is lost. The error message is "This computer can't connect to the remote computer." "Try connecting again. If the problem continues, contact the owner of the remote computer or your network administrator." A similar result with Telnet on port 3389. I am able to connect but if I hit a key the connection to host lost. The event log shows the successful login. No errors. Any ideas?

    Read the article

  • lshw not showing network

    - by triunenature
    Output: {User}@{Computer}:~$ sudo lshw -class network {User}@{Computer}:~$ Another Test: {User}@{Computer}:~$ lspci 00:00.0 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: NVIDIA Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: NVIDIA Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a2) 00:02.0 USB controller: NVIDIA Corporation MCP61 USB 1.1 Controller (rev a3) 00:02.1 USB controller: NVIDIA Corporation MCP61 USB 2.0 Controller (rev a3) 00:04.0 PCI bridge: NVIDIA Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: NVIDIA Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: NVIDIA Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: NVIDIA Corporation MCP61 Ethernet (rev a2) <<---- Network Card???? 00:08.0 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2) 00:08.1 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 FireWire (IEEE 1394): LSI Corporation FW322/323 (rev 70) 02:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9500 GT] (rev a1) If you look at 00:07.0 I believe that is the network card. However lshw doesnt show it. I mainly need information on network speed 10MBpS/100MBsP/1000MBpS Though knowing why my system isn't working would be nice.

    Read the article

  • Workgroup connection: You may not have permission

    - by Afiefh
    I have two Windows XP computers connected through an Ad-Hoc network, computer A creates the network and B connects to it. Both computers are on the Mshome network and have file and printer sharing enabled, and they can ping one another through the adhoc network. The result is that computer A can see computer B, but B cannot see A in the workgroup. But when A tries to access B I get a "you might not have permission to access" error telling me to contact the administrator. I tries to google the error, but most posts talk about problems connecting different versions of Windows to each other. I tried turning off the firewalls on both machines and checking if the required services are running. Nothing helped. Please excuse my ignorance on Windows networking, I haven't used Windows in around 10 years.

    Read the article

  • How to forward traffic using iptables rules?

    - by ProbablePattern
    I am new to iptables and I have been doing Google searches for a few days now without finding a good solution to this problem. I have computer A with a public ip address (say 192.0.2.1) that can access the Internet unrestricted. I have another computer B with a private ip address (192.168.1.1) that can only access computer A. How do I use iptables to forward network traffic from B through A to the Internet? I need to use http, ftp, and https in order to use apt-get with sudo. Both computers run Ubuntu linux. I have tried using Squid but I think it is far too complicated for what I need to do.

    Read the article

  • Setting up remote filesystem access without root privileges

    - by Luke Massa
    OK here's the situation. I have a computer A with complete admin access, and computer B (actually an account I login to) with very limited access. I am trying to make it so I can access a device on computer A (an external harddrive) on B. If I had more access to B, I would just mount the device on B, but I can't do that. I can ssh both directions, so theoretically I can copy data both directions, so it should be possible. I think a NFS might be helpful for me, but from what I've looked at, they all require the client to at some point perform a "mount" operation, something my client can't do. Thoughts?

    Read the article

  • Help trying/downloading ubuntu

    - by koolomwee
    I can't try ubuntu. Every time i put in my disk and press try, it shows the ubuntu sign with the dots under it than it shows a command screen basically blinking saying that it closed and canceled applications belonging to ubuntu... Than I tried to download it from the disk... same thing. Than, because I have windows, I tried to download it from the website and it worked. I rebooted my computer and went into the Ubuntu option just to find a blinking command screen again... How do I get ubuntu to work? What does happen (with the command screen) is that it shows commands that are blinking to fast for me to read the whole thing, and then it stops after like a minute or two of blinking. The only thing I do get to read is that Ubuntu commanded some applications to shut down. In the CD one it only has like 5 error messages, and when I reboot and select Ubuntu, there are over a hundred error messages. With the live-cd I have to shut down my computer to use it again. With the reboot and clicking ubuntu option it reboots by itself. I expect it to actually start up with no error messages. UPDATE I've been trying to start Ubuntu for the last couple of days, and I noticed on my last try that it said "SIGNAL 15 RECEIVED"... It also said that it's stopping Bluetooth and all other programs, and that its rebooting Maybe that'll help a little with answering my question... thanks :) this also might help: computer brand/model: HP Windows 7 Home Premium Service Pack 1, HPE240f graphics card: ATI Radeon HD 5570 I also wrote the same question here: https://answers.launchpad.net/wubi/+question/194537 might help a little more with information

    Read the article

< Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >