Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 166/287 | < Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >

  • Remove a known network from Windows 8

    - by Edward Brey
    When Windows 8 detects a network based on the assigned IP address, netmask, default gateway, etc., it remembers the network along with the setting you give it as a public or private network. If you change the configuration of a network (e.g. reconfigure your router), Windows may determine you are on a new network and assign it a name of Network 2 or YourAPN 2. This less-than-friendly name shows up in many places in the Windows 8 UI, but unlike the good old days of Windows 7, there doesn't appear to be any UI to merge or delete these networks. What's the best way to merge or delete networks you don't want?

    Read the article

  • Why is my ethernet interface in promiscuous mode

    - by nhed
    I read that seeing a flag of M in netstat -i is the way to tell which of your interfaces is in promiscuous mode I run it and I see that eth1 is in promiscuous mode $ netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth1 1500 0 1770161198 0 0 0 57446481 0 0 0 BMRU lo 16436 0 97501566 0 0 0 97501566 0 0 0 LRU This seems to be the case on all the machines I checked (All Centos6.0, both virtual and physical), any idea why ethernet devices would be in such a mode unless someone was running any pcap based app (sudo lsof | grep pcap shows nothing)? I did not see any mention of promiscuous in any of the config files (sudo grep -r promis /etc) Any ideas what puts the interface into that mode and why? p.s. most of the posts I see seem to be security related, this is not that

    Read the article

  • Why are my downloads up to ~1500KByte/sec only, when the ADSL connection locks at 13611Kbit/s?

    - by leladax
    No uploading is going on other than the overhead of downloading which appears to be not high for the abilities of the connection: Only about 30-40KByte/s when the router locks at 1012Kb/s and other direct uploads or uploading overheads can reach more than 100KByte/sec so I don't think it's a congestion at uploading that is doing it. Is there something I miss? Because I assume 13611Kbit/s should be ~1701Kbyte/sec. Is it an overheard at the ADSL level I don't understand? Could it be the ISP doing it? If it's active throttling it can't be on single connections since 2 high speed connections still go up to ~1500KByte/sec. It's not an example on torrents or other complex situations. The tests were on Ethernet, but I doubt the results would be different on wireless. I wonder if the settings of those connections at my end could be doing it, e.g. MTU settings, though I haven't touched the defaults of a common Realtek NIC.

    Read the article

  • Storage replication/mirror over WAN

    - by galitz
    Hello, We are looking at storage replication between two data centers (600km apart) to support an active-passive cluster design for disaster recovery. The OS layer will be mostly Windows Server 2003/2008 with some OpenSuSE Linux used for performance monitoring on VMWare or possibly XenServer. The primary application service to replicate is Nvision. Datacenter 1 will have two storage systems for local active-passive or perhaps active-active replication with Datacenter 2 used as a last resport disaster recovery site. We have a handle on most aspects, but I am looking for specific recommendations on storage platforms that can handle remote replication cleanly. Thanks.

    Read the article

  • What are good and bad jitter times for a LAN

    - by garyb32234234
    Ive just ran jperf (frontend to iperf) on our network between 2 workstations, its recorded jitter between 0.033ms and 0.048ms. Is this good or bad? Are there more variables that i would need to consider to make the decision? EDIT: TCP/IP Ethernet LAN 43 PCs 1 server, 100Mbits main switch, various small 8 port switches, test was done using UDP, Its a Windows Domain. I want to instal a few voip softphones on the workstations, see how many i can use that reliably work, im testing a few different workstations around the network to see where the best quality network paths are. Will also change some equipment if i identify bad connections.

    Read the article

  • Laptop loses signal from WiFi router, but mobile phone holds it fine

    - by Anton
    Hi, I have an extremely weird issue with my WiFi router. Both Ubuntu & Windows 7 can connect to it fine, but after 5-10 minutes browser (any one) stops opening pages and tells me it cannot resolve host address. But, at the same time, tools like Skype or BitTorrent work without any issues. I can also browse Internet on my mobile phone connected to the very same router. If I reset router it helps, but after 5-10 minutes I see just the same problem... Ubuntu tells me that WiFi signal is lost (mobile sees it), Windows 7 just won't let me browse anywhere. Can anyone give me a suggestion on this, please? Thanks

    Read the article

  • Unidentified network: How to configure TCP/IPv4 for Win7?

    - by Zolomon
    When I try to connect to internet I keep getting the error "Unidentified network". I've tried numerous attempts at restoring access without success. IP release, flushing DNS cache, reinstalling NIC, reactivating NIC, resetting router and so on... I've read several times that it's my default gateway that's wrong. Currently I've had automatic IP/DNS configuration set without any problems, and then it stopped working for some reason. Anyone know how I specify the IP? My subnetmask is 255.255.255.0, default gateway is 192.168.0.1 but I have no idea how to determine what IP I should set. I use a D-Link DIR-655 and other computers on the network have IPs like 192.168.0.194, next is 192.168.0.197. (I'm completely lost and am trying to cool down after two weekends of debugging filled with despair.)

    Read the article

  • Bypass network stack. Which options do we have? Pros and cons of each option [on hold]

    - by javapowered
    I'm writing trading application. I want to bypass network stack in Linux but I don't know how this can be done. I'm looking for complete list of options with pros and cons of each of them. The only option I know - is to buy solarflare network card which supports OpenOnLoad. What other options should I consider and what is pros and cons of each of them? Well the question is pretty simple - what is the best way to bypass network stack? upd: OpenOnload It achieves performance improvements in part by performing network processing at user-level, bypassing the OS kernel entirely on the data path. Intel DDIO to allow Intel® Ethernet Controllers and adapters to talk directly with the processor cache of the Intel® Xeon® processor E5. What's key difference between these techologies? Do they do roughly the same things? I much better like Intel DDIO because it's much easy to use, but OpenOnload required a lot of installation and tuning. If good OpenOnload application is much faster than good Intel DDIO application?

    Read the article

  • How to use a Network adapter only for a specific Connection on Win7?

    - by Tokk
    Hey, Guys I've got several network adapter in my PC (from LAN, WLAN, VPN etc...) and what I want to accomplish is that some specific adresses use the VPN adapter, while all others use eiter LAN or WLAN. (So for example http://win-server/ is using VPN, while www.google still uses LAN connection.) I've want to solve this with the Windows settings and not the VPN settings to make sure I can do it with every VPN-Provider. Thank You

    Read the article

  • How can I port forward over a VPN NAT?

    - by Charlie
    I have a multi-site VPN currently running with pfSense boxes and currently using OpenVPN. However I can change the OS and VPN type if need be. The main router has a 10.13.0.0/16 subnet and a series of public IPs For example, a branch has a 10.12.1.0/24 subnet How can I port forward NAT traffic on a public IP of the main router to a server behind the NAT of the second? So for instance port 95 on a public IP assigned to the main router forwards to 10.12.1.102 on the other router. Is this even possible? Currently my setup works great but only for intertnal traffic

    Read the article

  • Be your own cloud [closed]

    - by Jedi
    I have reasonably many electronic gadgets that can go LAN or WI-FI. But how do you share and/or syncronize all your files among them? Well, between my laptops and my desktop I use Dropbox. A nice way to share files among computers. But what if your HDD on your laptop is not large enough to carry music, pictures and films. Normally you would buy an extern USB HDD and store them there, but then you cannot reach the files from other computers which are not connected to the USB device. Many would say I should use a solution like a cloud with a disc station or something like that. But my needs are follows: A mass storage which can be reached among devices (laptops, desktops, iPhone, Android phone, XBox or Playstation). Has low power requirements and is silent. Can be reached inside home and it would be nice if it could be reached outside home as well. Cheap I have looked around and I have found an wireless router which can share a USB device: D-Link Wireless N HD Media Router. I thought it would be an interesting solution for a simple local cloud solution. D-Link uses a little program called SharePort Plus which mount the USB device to your computer. Unfortunately is the transfer rate to the USB storage device rather disappointing. The transfer rate was 5.8 Mbps even though the distance between the laptop and the router was 2 meter. The same is happening when I use cable from the computer to the router. Another thing is that SharePort Plus only allows one computer be connected to the device at a time. The last thing was something I could live with. I have search on the Internet for other solutions and found this video from Synology. I'm not sure if their solution is the right one. I think a disc station connected to my home LAN could the right solution. What have you done in your home to store and share files among your computers and game consoles?

    Read the article

  • WDS (Wireless Distribution System) not work

    - by xdevel2000
    I've a dlink di-524 as main router (192.168.0.1) connected to Internet and a second router (192.168.0.2), a tplink wr841n, with WDS enabled and correctly configured to "join" with dlink. After I connect via wireless a laptop (192.168.0.100) to tplink and both work good but with the laptop I can't go to Internet. It seems as WDS not work. With the laptop I can only ping the tplink but other ping (the dlink or other LAN computer not responding). What's the problem? Perhaps also the dlink must have the WDS option? Thanks.

    Read the article

  • How do I stop someone from saturating my line & wasting CPU cycles

    - by JoshRibs
    My web host shows inbound & outbound traffic with mrtg. I have a steady 3.5mbps inbound traffic from Nigeria. Even assuming the source IPs & destination ports are blocked with Iptables & verifying nothing is listening on those ports, will the traffic still always pass through the switch & "get" to my server (where my server wastes CPU cycles "dropping" the packets)? Assuming I was setup with a hardware firewall, the traffic would still show in mrtg assuming the firewall is behind the switch? So is there any way to stop someone from saturating your 100mbps line, if they also have a 100mbps line? Other than filing an abuse complaint with the kind folks in Nigeria?

    Read the article

  • Lenovo tools for windows 7: can't re-enable wireless

    - by pcampbell
    Consider a netbook - Lenovo S10e with Windows 7 and the S10 Lenovo power management tools. Machine has factory BIOS. Fn+F5 is the key combo to toggle the wireless radio on/off. The tool allows the disabling fine; works as expected. The problem is that the re-enable doesn't work, or is confusing on how to re-enable. Previously tried without success: Fn-F5 Fn-Ctrl-F5 Fn-Shift-F5 Fn-Alt-F5 Here's the onscreen display: Question: How can you re-enable the wireless radio using the Function key on a Lenovo netbook?

    Read the article

  • Set 802.1Q tagged port on VLAN1 on Dell PowerConnect switch

    - by Javier
    I'm having big troubles when adding this Dell switch to my network. Here we use several VLANs to segment traffic. All switches (3com and DLink mostly) have configured the same VLANs, most ports are 'untagged' and belong to a single VLAN, except for the ports used to join together the switches (in a star topology), these ports belong to all VLANs and use 802.1Q tags. So far, it works really well. But on this new switch (a Dell PowerConnect 5448), the settings are very different (and confusing). I have configured the same VLANs, an the uplink ports are set in 'general' mode (supposed to be fully 802.1Q compliant), I can set the VLAN membership as 'T' on these ports for all VLANs except VLAN 1. It always stay as 'U' on VLAN 1. Any ideas?

    Read the article

  • OpenVZ multiple networks on CTs

    - by user6733
    I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

    Read the article

  • PHP application failed to connect after a network plugged back in

    - by tntu
    My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

    Read the article

  • Testifying rasing net.core.somaxconn can make a difference

    - by petermolnar
    I got into an argument on the net.core.somaxconn parameter: I was told that it will not make any difference if we change the default 128. I believed this might be enough proof: "If the backlog argument is greater than the value in /proc/sys/net/core/somaxconn, then it is silently truncated to that value" http://linux.die.net/man/2/listen but it's not. Does anyone know a method to testify this with two machines, sitting on a Gbit network? The best would be against MySQL, LVS, apache2 ( 2.2 ), memcached.

    Read the article

  • Ubuntu - wireless connection works great but wired is totally dead

    - by Dan
    I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

    Read the article

  • Connecting to Aerohive AP's from Laptops running Win. 7 using authentication from a Windows 2008 domain server

    - by user264116
    I have deployed a wireless network using Aerohive access points. 2 of them are set up as radius servers. I want my users to be able to use the same user name and password they use when they log onto our domain. They are able to do this from android devices or computers running Windows 8. It will not work on Windows 7 machines. How do I remedy this situation, keeping in mind that the machines are personal machines not company owned and I will have no way to change their hardware or software.

    Read the article

  • Internet setup for my office

    - by prakash
    We have two internet connections to our office and our current setup is like this.. The internet connections require pppoe log in so i take each cable and plug it into a wifi router and configure the router to log in to the pppoe and then plug in a cable from the router to a switch and distribute the internet throughout my office. The problem with this setup is it is really hard to monitor and im not able to monitor who is hogging internet usage and what he or she is actually using it for. apart from this we also have a nas setup which is routed through another switch . Could someone please throw a little light on how i can restructure this setup for easy monitoring and better transparency... ? each wan router is connected to a different switch and is distributed to users accordingly.. we have around 40 users in the office.. we want to setup a single linux box to which i want to connect the two wan connections and from there distribute it to all our users.... im looking for a solution where we do not have to invest more that buying a single pc and a couple of nics

    Read the article

  • Ubuntu, connecting to WLAN

    - by Holly
    Hello, I successfully installed Ubuntu onto my usb hard drive. However, I'm not sure what the issue is with my internet. I'm not familiar enough with ubuntu to know whether this is a problem with recognizing my wireless card or with my internet, etc. So I suppose my question is, how do I tell whether it's recognizing my wireless card? (Network manager isn't showing any wireless signals, though I wasn't sure if it was supposed to. ) And, if it's not working, how do I go about troubleshooting that issue? Thanks!

    Read the article

  • How to combine AWS and dedicated external servers?

    - by rfw21
    I have an extensive network of servers all currently hosted on AWS EC2. For reasons of cost I plan to gradually migrate to dedicated servers where possible. So: How can I best combine AWS and non-AWS servers in my network? Ideally, I should be able to assign internal IP addresses to the external servers, include them in AWS security groups and ensure that all private traffic between my AWS servers and external servers is secure.

    Read the article

  • WGet from one site on a server to another site on the same server

    - by JoshReedSchramm
    Hey all, I've recently been asked to administer a couple ubuntu boxes running web servers. I'm a dev by trade so if this question is fairly noob please forgive. We have about a dozen sites running on this box. 2 of our sites need to talk back and forth over a restful api. Unfortunately we are having issues with the sited connection to each other via wget. When we try and run wget manually from the command line from the server pointing to a site also on that server it hangs and eventually times out. If we do the same thing from outside the server to the same site on the server it works. Is there something that could be preventing sites on the same server from communicating with each other? The same thing happens pinging the site from the server.

    Read the article

< Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >