Search Results

Search found 4628 results on 186 pages for 'gridview editing'.

Page 167/186 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

• How to transition to Comcast with static IP address [migrated]

  - by steveha

  I have my own email server in my house, on a static IP address. I have had business DSL for over a decade, but I also now have Comcast business Internet. I want to transition from the DSL to the Comcast, and I have some questions. I have a domain name, my own mail server, and a firewall (a PC with two network interfaces, running Devil-Linux). I need to make sure I understand how to set up the Comcast cable box, and how to set up my firewall. First, do I need to change any settings in the cable box? Currently I have only used the cable box by plugging in a laptop, with the laptop doing DHCP. I think I can leave the box alone but I would like to make sure. Second, I'm not sure I understand the instructions Comcast gave me for setting up the firewall. My DSL provider gave me the following information: static IP address, net mask, gateway, and two DNS servers. Comcast gave me: static IP address, routable static IP address, net mask, and two DNS servers, and told me to put the "static IP address" as the "gateway" on the firewall. Is this just Comcast-speak here? Does "routable static IP address" mean the same thing as "static IP address" in my DSL setup, the end-point address that I should publish in the DNS MX records for my email server? Or should I publish the "static IP address", and Comcast will then route all its traffic over the cable box? My plan is: first, I'm going to configure another firewall, so I have one firewall for the DSL and one for the Comcast (rather than madly editing settings to switch back and forth). Then I will publish the new Comcast static IP address as a backup email server address in the DNS MX records, wait a while to let it propagate, and then switch my home over from the DSL to the Comcast. Then I'll change DNS to make that the primary mail address and the DSL the secondary, let that go a while and make sure it seems reliable. Then I'll remove the DSL from the DNS MX records completely, and finally shut down the DSL service. (I thought about keeping the DSL as a backup, but the reason I'm leaving DSL is that it has become unreliable; and I have heard that Comcast business Internet is reliable.) Final question, any advice for me? Anything you think might be useful, helpful, or educational. Thanks.

  Read the article

• In search of a network file system with extended caching to speed up file access

  - by Brecht Machiels

  I'm running a small home server that stores my documents. The disks in this server are in a RAID 1 configuration (using Linux md) and it's also periodically being backup up to an external hard drive to make sure I don't lose them. However, I'm always accessing the files from other computers on the home network using an SMB share, and this results in a considerable speed penalty (especially when connected over WLAN). This is quite annoying when editing large files, such as digital camera RAWs, for example. I've been looking for a solution to this problem. It would have to offer some kind of local caching to speed up the file access. The client would preferably not keep a copy of all data on the server, as it consists of a very large collection of photographs, most of which I will not access frequently. Instead, it should only cache the accessed files and sync the changes back in the background. Ideally, it would also do some smart read-ahead (cache the files that are in the same directory as the currently opened file, for examples), but I suppose that's asking a bit much. Synchronization should be automatic (on file change). Conflicting file changes (at the same time on different clients) are unlikely to happen in my use case, but I would prefer if they are handled properly (notification to the user). I've come across the following options, so far: something similar to Dropbox. iFolder seems to be the only thing that comes close, but its reputation (stability) and requirements put me off. A distributed file system such as OpenAFS. I'm not sure this will speed up file access. It is probably overkill for what I need. Maybe NFS or even Samba offer these possibilities. I read a bit about Windows' Offline Files, but its operation seems limited (at least on Windows XP). As this is just for personal use, I'm not willing to spend a lot of money. A free solution would be preferred. Also, the server needs to run on Linux, and I need a client for at least Windows.

  Read the article

• MySQL: Pacemaker cannot start the failed master as a new slave?

  - by quanta

  I'm going to setup failover for MySQL replication (1 master and 1 slave) follow this guide: https://github.com/jayjanssen/Percona-Pacemaker-Resource-Agents/blob/master/doc/PRM-setup-guide.rst Here're the output of crm configure show: node serving-6192 \ attributes p_mysql_mysql_master_IP="192.168.6.192" node svr184R-638.localdomain \ attributes p_mysql_mysql_master_IP="192.168.6.38" primitive p_mysql ocf:percona:mysql \ params config="/etc/my.cnf" pid="/var/run/mysqld/mysqld.pid" socket="/var/lib/mysql/mysql.sock" replication_user="repl" replication_passwd="x" test_user="test_user" test_passwd="x" \ op monitor interval="5s" role="Master" OCF_CHECK_LEVEL="1" \ op monitor interval="2s" role="Slave" timeout="30s" OCF_CHECK_LEVEL="1" \ op start interval="0" timeout="120s" \ op stop interval="0" timeout="120s" primitive writer_vip ocf:heartbeat:IPaddr2 \ params ip="192.168.6.8" cidr_netmask="32" \ op monitor interval="10s" \ meta is-managed="true" ms ms_MySQL p_mysql \ meta master-max="1" master-node-max="1" clone-max="2" clone-node-max="1" notify="true" globally-unique="false" target-role="Master" is-managed="true" colocation writer_vip_on_master inf: writer_vip ms_MySQL:Master order ms_MySQL_promote_before_vip inf: ms_MySQL:promote writer_vip:start property $id="cib-bootstrap-options" \ dc-version="1.0.12-unknown" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1341801689" property $id="mysql_replication" \ p_mysql_REPL_INFO="192.168.6.192|mysql-bin.000006|338" crm_mon: Last updated: Mon Jul 9 10:30:01 2012 Stack: openais Current DC: serving-6192 - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, 2 expected votes 2 Resources configured. ============ Online: [ serving-6192 svr184R-638.localdomain ] Master/Slave Set: ms_MySQL Masters: [ serving-6192 ] Slaves: [ svr184R-638.localdomain ] writer_vip (ocf::heartbeat:IPaddr2): Started serving-6192 Editing /etc/my.cnf on the serving-6192 of wrong syntax to test failover and it's working fine: svr184R-638.localdomain being promoted to become the master writer_vip switch to svr184R-638.localdomain Current state: Last updated: Mon Jul 9 10:35:57 2012 Stack: openais Current DC: serving-6192 - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, 2 expected votes 2 Resources configured. ============ Online: [ serving-6192 svr184R-638.localdomain ] Master/Slave Set: ms_MySQL Masters: [ svr184R-638.localdomain ] Stopped: [ p_mysql:0 ] writer_vip (ocf::heartbeat:IPaddr2): Started svr184R-638.localdomain Failed actions: p_mysql:0_monitor_5000 (node=serving-6192, call=15, rc=7, status=complete): not running p_mysql:0_demote_0 (node=serving-6192, call=22, rc=7, status=complete): not running p_mysql:0_start_0 (node=serving-6192, call=26, rc=-2, status=Timed Out): unknown exec error Remove the wrong syntax from /etc/my.cnf on serving-6192, and restart corosync, what I would like to see is serving-6192 was started as a new slave but it doesn't: Failed actions: p_mysql:0_start_0 (node=serving-6192, call=4, rc=1, status=complete): unknown error Here're snippet of the logs which I'm suspecting: Jul 09 10:46:32 serving-6192 lrmd: [7321]: info: rsc:p_mysql:0:4: start Jul 09 10:46:32 serving-6192 lrmd: [7321]: info: RA output: (p_mysql:0:start:stderr) Error performing operation: The object/attribute does not exist Jul 09 10:46:32 serving-6192 crm_attribute: [7420]: info: Invoked: /usr/sbin/crm_attribute -N serving-6192 -l reboot --name readable -v 0 The full logs: http://fpaste.org/AyOZ/ The strange thing is I can starting it manually: export OCF_ROOT=/usr/lib/ocf export OCF_RESKEY_config="/etc/my.cnf" export OCF_RESKEY_pid="/var/run/mysqld/mysqld.pid" export OCF_RESKEY_socket="/var/lib/mysql/mysql.sock" export OCF_RESKEY_replication_user="repl" export OCF_RESKEY_replication_passwd="x" export OCF_RESKEY_test_user="test_user" export OCF_RESKEY_test_passwd="x" sh -x /usr/lib/ocf/resource.d/percona/mysql start: http://fpaste.org/RVGh/ Did I make something wrong?

  Read the article

• why can't I open a port on Win 7? is it the app's fault?

  - by rjnagle

  I am having problems opening a port from one Windows PC on my local network. On Windows 7 computer ("Computer A") I running Calibre, an ebook management program that has something called an "ebook content server" . In essence, it serves via the web a content catalog. From Computer A, I can access the content server on localhost. ie. http://127.0.0.1:8787 calls up the content server successfully. With ipconfig I have confirmed that its local IP address is 192.168.1.106 From Computer B (a Vista Machine) I can ping 192.168.1.106 I have tried opening/editing a port in the Windows Firewall several times. In Windows firewall -- Allowed Programs in Control Panel, I see a listing for Calibre (with both Home/Work and PUblic checked) In details, I see Name: Calibre, Port Number 8787, Protocol TCP If I use the Advanced Security configuration screen for the firewall, I created an Inbound Rule on Computer A for Calibre (with the settings I indicated). If I run this command line on Computer A, I see: netstat -a -n TCP 0.0.0.0:554 0.0.0.0:0 LISTENING TCP 0.0.0.0:664 0.0.0.0:0 LISTENING TCP 0.0.0.0:2869 0.0.0.0:0 LISTENING TCP 0.0.0.0:3306 0.0.0.0:0 LISTENING TCP 0.0.0.0:5357 0.0.0.0:0 LISTENING TCP 0.0.0.0:6570 0.0.0.0:0 LISTENING TCP 0.0.0.0:6580 0.0.0.0:0 LISTENING TCP 0.0.0.0:8787 0.0.0.0:0 LISTENING TCP 0.0.0.0:10243 0.0.0.0:0 LISTENING TCP 192.168.1.106:63020 74.125.227.51:80 TIME_WAIT TCP [::]:80 [::]:0 LISTENING TCP [::]:135 [::]:0 LISTENING TCP [::]:443 [::]:0 LISTENING TCP [::]:445 [::]:0 LISTENING TCP [::]:554 [::]:0 LISTENING TCP [::]:2869 [::]:0 LISTENING TCP [::]:5357 [::]:0 LISTENING TCP [::]:6570 [::]:0 LISTENING TCP [::]:6580 [::]:0 LISTENING TCP [::]:10243 [::]:0 LISTENING TCP [::]:49152 [::]:0 LISTENING TCP [::]:49153 [::]:0 LISTENING TCP [::]:49154 [::]:0 LISTENING TCP [::]:49155 [::]:0 LISTENING TCP [::]:49170 [::]:0 LISTENING And lots of other junk, but this seems relevant, I see port 80 is open (I run xampp apache web server for windows on Machine A) This is the only time I see port 8787 referenced from the netstat commmand. From Windows Computer B, I can, ping 192.168.1.106 and even view http://drupal.local (on Computer A) and http://192.168.1.106/ (which goes to the Xampp config screen on Computer A). But I cannot access via Computer B htttp://192.168.1.106:8787 or htttp://computerhosta:8787 So what is going wrong? Is this a problem with the Calibre application or have I incorrectly opened the port? What things could possibly interfere with the opening of this port? On a sidenote, I have tried using telnet from Computer B to see if port 80 or 8787 is open for 192.168.1.106. I get no reply for either one. Thanks.

  Read the article

• Profiles and using the local profile for a domain user

  - by Harry

  I’m having some trouble with profiles and would like to reach out for some help. I’ve tried to do some research to help myself along, but I’m not making much progress on my own. I’ve pretty much taken over the sys admin duties for my small lab, I don’t have much experience to justify it besides I’m the only with the time and dedication to go at it (The environment was in a state of disrepair). My network and domain I look over are extremely small by most standards, about 10 users at a time. They are pretty intensive activity on the network, and we do work with fairly large files. None of the network is online, which is nice at the moment because it allows me not to have another headache. On to my profile problem, I have set up roaming profiles for the users in the network. Now after a little research, I think I will be switching this to a hybrid of folder redirection and roaming profiles as this seems to best practice. I also don’t want the users having to wait for a long time if they have a bloated profile. Now I’ve finally got a build working using MDT. We have Mac Pros, and it wasn’t fun getting everything to play nice. The way I did this was by setting up a reference computer and installing all the software and tools that each user would need and editing the settings preferences to how we would need them. I think used MDT to do a sys prep and capture to create the image of my reference computer. Using the reference image I can push out my images to the rest of the desktops in my environment. The issue I’m having is when we join the computer to domain. The user can login and operate fine on the computer, but I’d like a more. When the user is logged on with their domain user name they lose a lot of the icons I had on my reference image, as well as the desktop background and some other miscellaneous settings. I would love to have the user log on using their domain user name and see the icons and desktop environment as I had it setup on the reference computer. I’m not sure if it is possible, or something simple that I’m missing, but any help would be greatly appreciated!

  Read the article

• Windows 7 playback of dvr-Microsoft files stutters

  - by Jim Lynn

  I've just had to install Windows 7 on my Media Center machine because my Vista installation had a faulty drive. I've got the latest drivers that I can find - Intel 945GM integrated Graphics, Realtek audio drivers. Things are working OK with one exception. Playback of old recordings, from dvr-Microsoft format files, is choppy. The picture freezes for a fraction of a second, then quickly catches up. The sound is uninterrupted and doesn't pause. These freezes happen once every 5 seconds or so. It's very regular. Playback of Live TV from the digital tuner is perfectly smooth. DVD playback is perfectly smooth. As an experiment, I used the MPEG editing package VideoReDo to create a small test file in three different formats. This program takes the raw MPEG streams and repackages them into the desired container. I took the same clip and created three files in three formats: dvr-Microsoft (Microsoft's old recorded TV format); mpg (standard MPEG); and ts (raw MPEG transport stream of the kind often produced by PVRs). When these three files are played back under Windows 7, the mpg and ts files play smoothly, but the dvr-Microsoft file stutters. The last piece of data I have is that two other Windows 7 machines can play back dvr-Microsoft files smoothly with no stuttering. One is a netbook, with less grunt than the media centre. So there must be something specific about my Media Center machine that's causing the problem. Does anyone have any idea where I can look now? I don't know much about AV software, codecs, filter graphs etc. but I suspect that's where the problem lies. Rendering the video isn't the problem, but extracting the streams is. How would I go about diagnosing the problem? Edited to add: I just used the GraphStudio tool to look at the filter graph on the offending PC. The filter graph it uses by default for dvr-Microsoft looks identical to the other machines, and, interestingly, when I play the files using GraphStudio they run smoothly. Under Windows Media Player and Windows Media Center they stutter. I'd like to see the filter graph for Windows Media Player but GraphStudio won't show it. It looks like Windows Media Player and WMC are using a different decoding path to GraphStudio. Edited again to add: Today I purchased a new HDTV. The same Media Center driving the TV at 1080p is now playing back the old Recorded TV files smoothly, without stuttering. So whatever the cause of the original problem, using a different resolution seems to have removed the problem. It might also explain why nobody else has had this problem. I doubt many people use Media Centre with a 14in portable TV.

  Read the article

• Populating ComboBoxDataColumn items and values

  - by MarceloRamires

  I have a "populate combobox", and I'm so happy with it that I've even started using more comboboxes. It takes the combobox object by reference with the ID of the "value set" (or whatever you want to call it) from a table and adds the items and their respective values (which differ) and does the job. I've recently had the brilliant idea of using comboboxes in a gridview, and I was happy to notice that it worked JUST LIKE a single combobox, but populating all the comboboxes in the given column at the same time. ObjComboBox.Items.Add("yadayada"); //works just like ObjComboBoxColumn.Items.Add("blablabla"); But When I started planning how to populate these comboboxes I've noticed: There's no "Values" property in ComboBoxDataColumn. ObjComboBox.Values = whateverArray; //works, but the following doesn't ObjComboBoxColumn.Values = whateverArray; Questions: 0 - How do I populate it's values ? (I suspect it's just as simple, but uses another name) 1 - If it works just like a combobox, what's the explanation for not having this attribute ? -----[EDIT]------ So I've checked out Charles' quote, and I've figured I had to change my way of populating these bad boys. Instead of looping through the strings and inserting them one by one in the combobox, I should grab the fields I want to populate in a table, and set one column of the table as the "value", and other one as the "display". So I've done this: ObjComboBoxColumn.DataSource = DTConfig; //Double checked, guaranteed to be populated ObjComboBoxColumn.ValueMember = "Code"; ObjComboBoxColumn.DisplayMember = "Description"; But nothing happens, if I use the same object as so: ObjComboBoxColumn.Items.Add("StackOverflow"); It is added. There is no DataBind() function. It finds the two columns, and that's guaranteed ("Code" and "Description") and if I change their names to nonexistant ones it gives me an exception, so that's a good sign. -----[EDIT]------ I have a table in SQL Server that is something like code  |  text —————    1    | foo    2    | bar It's simple, and with other comboboxes (outside of gridviews) i've successfully populated looping through the rows and adding the texts: ObjComboBox.Items.Add(MyDataTable.Rows[I]["MyColumnName"].ToString()); And getting every value, adding it into an array, and setting it like: ObjComboBox.Values = MyArray; I'd like to populate my comboboxColumns just as simply as I do with comboboxes.

  Read the article

• How to troubleshoot performance issues of PHP, MySQL and generic I/O

  - by jbx

  I have a WordPress based website running on a shared hosting. Its response time is very decent (around 2s to retrieve the HTML page and 5s to load all the resources). I was planning to move it to a dedicated virtual server (Ubuntu 12.04 LTS), which should theoretically improve things and make them more consistent given its not shared. However I observed severe performance degredation, with the page taking 10seconds to be generated. I ruled out network issues by editing /etc/hosts on the server and mapping the domain to 127.0.0.1. I used the Apache load tester ab to get the HTML, so JS, CSS and images are all excluded. It still took 10 seconds. I have Zpanel installed on the server which also uses MySQL, and its pages come up quite fast (1.5s) and also phpMyAdmin. Performing some queries on the wordpress database directly through phpMyAdmin returns them quite fast too, with query times in the 10 to 30 millisecond region. Memory is also sufficient, with only 800Mb being used of the 1Gb physical memory available, so it doesn't seem to be a swap issue either. I have also installed APC to try to improve the PHP performance, but it didn't have any effect. What else should I look for? What could be causing this degradation in performance? Could it be some kind of I/O issue since I am running on a cloud based virtual server? I wish to be able to raise the issue with my provider but without showing actual data from some diagnosis I am afraid he will just blame my application. UPDATE with sar output (every second) when I did an HTTP request: 02:31:29 CPU %user %nice %system %iowait %steal %idle 02:31:30 all 0.00 0.00 0.00 0.00 0.00 100.00 02:31:31 all 2.22 0.00 2.22 0.00 0.00 95.56 02:31:32 all 41.67 0.00 6.25 0.00 2.08 50.00 02:31:33 all 86.36 0.00 13.64 0.00 0.00 0.00 02:31:34 all 75.00 0.00 25.00 0.00 0.00 0.00 02:31:35 all 93.18 0.00 6.82 0.00 0.00 0.00 02:31:36 all 90.70 0.00 9.30 0.00 0.00 0.00 02:31:37 all 71.05 0.00 0.00 0.00 0.00 28.95 02:31:38 all 14.89 0.00 10.64 0.00 2.13 72.34 02:31:39 all 2.56 0.00 0.00 0.00 0.00 97.44 02:31:40 all 0.00 0.00 0.00 0.00 0.00 100.00 02:31:41 all 0.00 0.00 0.00 0.00 0.00 100.00 My suspicion that this comes from I/O related issue is also because a caching plugin I use to reduce the amount of queries to the database, by precompiling PHP pages is actually making things worse instead of better. It seems that file access is making things worse instead.

  Read the article

• Use launchctl to fire an AppleScript script periodically

  - by Daktari

  I have written an AppleScript that lets me back up a particular file. The script runs fine inside AppleScript Editor: it does what it's supposed to do perfectly. So far so good. Now I'd like to run this script at timed intervals. So I use launchctl & .plist to make this happen. That's where the trouble starts. the script is loaded at set interval by launchctl the AppleScript Editor (when open) brings its window (with that script) to the foreground but no code is executed when AppleScript Editor is not running, nothing seems to be happening at all Any ideas as to why this is not working? -- After editing (as per Daniel Beck's suggestions) my plist now looks like: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>KeepAlive</key> <false/> <key>Label</key> <string>com.opera.autosave</string> <key>ProgramArguments</key> <array> <string>osascript</string> <string>/Users/user_name/Library/Scripts/opera_autosave_bak.scpt</string> </array> <key>StartInterval</key> <integer>30</integer> </dict> </plist> and the AppleScript I'm trying to run: on appIsRunning(appName) tell application "System Events" to (name of processes) contains appName end appIsRunning --only run this script when Opera is running if appIsRunning("Opera") then set base_path to "user_name:Library:Preferences:Opera Preferences:sessions:" set autosave_file to "test.txt" set autosave_file_old to "test_old.txt" set autosave_file_older to "test_older.txt" set autosave_file_oldest to "test_oldest.txt" set autosave_path to base_path & autosave_file set autosave_path_old to base_path & autosave_file_old set autosave_path_older to base_path & autosave_file_older set autosave_path_oldest to base_path & autosave_file_oldest set copied_file to "test copy.txt" set copied_path to base_path & copied_file tell application "Finder" duplicate file autosave_path delete file autosave_path_oldest set name of file autosave_path_older to autosave_file_oldest set name of file autosave_path_old to autosave_file_older set name of file copied_path to autosave_file_old end tell end if

  Read the article

• Enterprise Tape Backup solutions

  - by Tom O'Connor

  I'm currently attempting to re-architect a backup solution where I'm working. We've got 2 NAS devices, one in the office, one in the datacentre. The servers in the DC back up to the DC NAS, which is then replicated to the Office NAS. The office NAS exports shares as CIFS and NFS, this bit is fine. At some point, I'll have to expand our storage capacity, currently we've got about 1.4TB of storage space, which is about 96% full. Previously, the tape backup was a script that ran tar a few times and squirted data onto a tape. It worked, but was by no means a perfect solution. Restores are a bit of a pest, adding new data to the backup requires editing the script as root. It's just all a bit non-ideal. I've been evaluating a number of "enterprise" ready backup solutions, such as Yosemite Backup from Barracuda, Acronis Backup/Restore, and something from Arkeia. In the process of evaluating these, I've found 2 big problems. Not all of them allow backup of mounted devices (such as a NFS mounted NAS) Many of these applications don't like our tape device. For the most part, (1) is essential. Our NAS has a feeble processor and can't run applications like backup agents. I suspect that the biggest problem is the tape device, which is a HP C7438A DAT72 connected via USB. Questions: Has anyone else got an USB DAT72 device working with similar software? Is there a better way to back up data from an "appliance" NAS device on which you can't run an agent? Would I be totally out of my mind to specify a cheap HP or Dell server with a couple of 1TB hard disks, and a SAS card to then talk to an HP Ultrium (or similar) device? The biggest drawback to this would be cost (400ish for the server, 200 for the SAS connectivity and 1700 for a LTO4 device) Notes: I'd love to be able to say that I'd get rid of tapes entirely, and use some form of hard disk backup. In a previous job, we had LaCie USB drives, which were decidedly unreliable.

  Read the article

• RAID 50 24Port Fast Writes Slow Reads - Ubuntu

  - by James

  What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

  Read the article

• Adding ComboBoxItem to a combobox inside a user control (XAML/WPF)

  - by byte

  I am currently learning to create custom controls in WPF. I successfully created a simple custom control using a Label and a Text Box. I was able to allow setting the Label text by DependencyProperty. Now I am creating a user control that has a ComboBox. I need to allow adding items to this ComboBox from outside the control. To achieve this, I tried exposing a DependencyProperty of type ItemsCollection and it will allows access to the ComboBox's Items property (the DP in my control sample is named 'CbItems'). But I get errors because Items property of Combobox is ReadOnly. Control XAML <UserControl x:Class="MyWpfApp.Controls.MyControl" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Height="Auto" Width="Auto"> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition /> <ColumnDefinition /> </Grid.ColumnDefinitions> <Label Grid.Column="0" Content="{Binding FieldLabel}"></Label> <ComboBox Name="cmb" Grid.Column="1" Width="150"></ComboBox> </Grid> </UserControl> MainWindow XAML <Window x:Class="MyWpfApp.Window1" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:ctl="clr-namespace:MyWpfApp.Controls" Title="Window1" Height="300" Width="300"> <Grid> <ctl:MyControl> <ctl:MyControl.CbItems> <ComboBoxItem>Hello</ComboBoxItem> <ComboBoxItem>World</ComboBoxItem> <ComboBoxItem>Hi</ComboBoxItem> </ctl:LobCombox.CbItems> </ctl:LobCombox> </Grid> </Window> I would like to know what the correct way is to achieve this functionality. I believe the answer to this might also help with other controls like GridView etc Many Thanks

  Read the article

• Optimal setup for ASUS P6X58D Premium BIOS (no OC)?

  - by rumtscho

  Normally, I'd trust the mainboard manufacturer to choose the best options as defaults. But I had trouble with the board, because even with Quick Boot enabled, it booted twice as slowly as a Pentium 4 Celeron. Then I changed lots of options at once (most of them weren't explained in the manual, just mentioned with a single sentence) and the boot time is only marginally worse than the Pentium 4 (54 sec against 46 sec from button to pw entering screen). Now I don't know if I have turned something off which should have stayed on. I guess I even won't be able to boot from a CD now, because even though it is present in the boot sequence, I took off a timeout I think it needs to check whether there is a disk in the drive. The second reason is that I don't have an internal HDD, only a SSD. I forgot my sources blush but I am under the impression that today's BIOS and OS options are geared toward booting from a HDD, which is often less than optimal when one boots from a SSD, especially when there are functions which cause avoidable writing cycles, as a SSD wears out after too many writing cycles. Most of the things I've read concern the OS, but there are some BIOS-relevant options too. I am especially confused about the disk mode. The board supports AHCI, IDE-simulation and RAID, but of the different articles I've read, there is a proponent for each and no clear arguments for any. So can one tell me which options are important in general and which are important for a SSD-only system? I don't want to overclock the CPU, so you don't have to say anything about this (yes I know the board is meant for OC:)). I am thinking of overclocking the RAM, since they sold me 1600er heatsinked modules which are running at 1066 now, but I'm not sure yet about that. The rest of the system: i7-930, Intel X25-m G2, 6 GB RAM, GTS 250, some no-name Blue-ray ROM. 2 external HDDs over USB 2.0. Lots of other USB-connected hardware (12 devices I think), no SATA 3 drives (will disabling the controller have an impact on performance?), no LAN, only WiFi. Lucid Lynx 64 bit, no dual boot, no virtual installations. The main uses of the system are: managing and playing/showing all the media stored on the external disks, lots of image manipulation, some video editing, a bit of (non-demanding) gaming, rarely development. Lots of Internet surfing too, but this shouldn't have much impact on performance.

  Read the article

• ASP.NET Client to Server communication

  - by Nelson

  Can you help me make sense of all the different ways to communicate from browser to client in ASP.NET? I have made this a community wiki so feel free to edit my post to improve it. Specifically, I'm trying to understand in which scenario to use each one by listing how each works. I'm a little fuzzy on UpdatePanel vs CallBack (with ViewState): I know UpdatePanel always returns HTML while CallBack can return JSON. Any other major differences? ...and CallBack (without ViewState) vs WebMethod. CallBack goes through most of the Page lifecycle, WebMethod doesn't. Any other major differences? IHttpHandler Custom handler for anything (page, image, etc.) Only does what you tell it to do (light server processing) Page is an implementation of IHttpHandler If you don't need what Page provides, create a custom IHttpHandler If you are using Page but overriding Render() and not generating HTML, you probably can do it with a custom IHttpHandler (e.g. writing binary data such as images) By default can use the .axd or .ashx file extensions -- both are functionally similar .ashx doesn't have any built-in endpoints, so it's preferred by convention Regular PostBack (System.Web.UI.Page : IHttpHandler) Inherits Page Full PostBack, including ViewState and HTML control values (heavy traffic) Full Page lifecycle (heavy server processing) No JavaScript required Webpage flickers/scrolls since everything is reloaded in browser Returns full page HTML (heavy traffic) UpdatePanel (Control) Control inside Page Full PostBack, including ViewState and HTML control values (heavy traffic) Full Page lifecycle (heavy server processing) Controls outside the UpdatePanel do Render(NullTextWriter) Must use ScriptManager If no client-side JavaScript, it can fall back to regular PostBack with no JavaScript (?) No flicker/scroll since it's an async call, unless it falls back to regular postback. Can be used with master pages and user controls Has built-in support for progress bar Returns HTML for controls inside UpdatePanel (medium traffic) Client CallBack (Page, System.Web.UI.ICallbackEventHandler) Inherits Page Most of Page lifecycle (heavy server processing) Takes only data you specify (light traffic) and optionally ViewState (?) (medium traffic) Client must support JavaScript and use ScriptManager No flicker/scroll since it's an async call Can be used with master pages and user controls Returns only data you specify in format you specify (e.g. JSON, XML...) (?) (light traffic) WebMethod Class implements System.Web.Service.WebService HttpContext available through this.Context Takes only data you specify (light traffic) Server only runs the called method (light server processing) Client must support JavaScript No flicker/scroll since it's an async call Can be used with master pages and user controls Returns only data you specify, typically JSON (light traffic) Can create instance of server control to render HTML and sent back as string, but events, paging in GridView, etc. won't work PageMethods Essentially a WebMethod contained in the Page class, so most of WebMethod's bullet's apply Method must be public static, therefore no Page instance accessible HttpContext available through HttpContext.Current Accessed directly by URL Page.aspx/MethodName (e.g. with XMLHttpRequest directly or with library such as jQuery) Setting ScriptManager property EnablePageMethods="True" generates a JavaScript proxy for each WebMethod Cannot be used directly in user controls with master pages and user controls Any others?

  Read the article

• Enable PostBack for a ASP.NET User Control

  - by Steven

  When I click my "Query" the values for my user controls are reset. How do I enable PostBack for my user control? myDatePicker.ascx <%@ Control Language="vb" CodeBehind="myDatePicker.ascx.vb" Inherits="Website.myDate" AutoEventWireup="false" %> <%@ Register assembly="AjaxControlToolkit" namespace="AjaxControlToolkit" tagprefix="asp" %> <asp:TextBox ID="DateTxt" runat="server" ReadOnly="True" /> <asp:Image ID="DateImg" runat="server" ImageUrl="~/Calendar_scheduleHS.png" EnableViewState="True" EnableTheming="True" /> <asp:CalendarExtender ID="DateTxt_CalendarExtender" runat="server" Enabled="True" TargetControlID="DateTxt" PopupButtonID="DateImg" DefaultView="Days" Format="ddd MMM dd, yyyy" EnableViewState="True"/> myDatePicker.ascx Partial Public Class myDate Inherits System.Web.UI.UserControl Public Property SelectedDate() As Date? Get Dim o As Object = ViewState("SelectedDate") If o = Nothing Then Return Nothing End If Return Date.Parse(o) End Get Set(ByVal value As Date?) ViewState("SelectedDate") = value End Set End Property End Class Default.aspx <%@ Page Language="vb" AutoEventWireup="false" CodeBehind="Default.aspx.vb" Inherits="Website._Default" EnableEventValidation="false" EnableViewState="true" %> <%@ Register TagPrefix="my" TagName="DatePicker" Src="~/myDatePicker.ascx" %> <%@ Register Assembly="AjaxControlToolkit" Namespace="AjaxControlToolkit" TagPrefix="ajax" %> <%@ Register Assembly="..." Namespace="System.Web.UI.WebControls" TagPrefix="asp" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> ... <body> <form id="form1" runat="server"> <div class="mainbox"> <div class="query"> Start Date<br /> <my:DatePicker ID="StartDate" runat="server" EnableViewState="True" /> End Date <br /> <my:DatePicker ID="EndDate" runat="server" EnableViewState="True" /> ... <div class="query_buttons"> <asp:Button ID="Button1" runat="server" Text="Query" /> </div> </div> <asp:GridView ID="GridView1" ... > </form> </body> </html> Default.aspx.vb Imports System.Web.Services Imports System.Web.Script.Services Imports AjaxControlToolkit Protected Sub Page_Load(ByVal sender As Object, _ ByVal e As EventArgs) Handles Me.Load End Sub Partial Public Class _Default Inherits System.Web.UI.Page Protected Sub Button1_Click(ByVal sender As Object, _ ByVal e As EventArgs) Handles Button1.Click GridView1.DataBind() End Sub End Class

  Read the article

• Passwordless ssh failed when login using username

  - by Aczire

  I was trying to setup Hadoop and was stumbled on passwordless ssh to localhost. I am getting a password prompt when trying to connect using ssh username@hostname format. But there is no problem connecting to the machine like ssh localhost or ssh hostname.com. Tried ssh-copy-id user@hostname but it did not work. Using CentOS 6.3 as normal user, I neither have root access or am a sudoer so editing any files like sshd_config is not possible (not even cat the sshd_config file contents). I hope the user login is possible since I can do login without password to localhost, right? Please advise, Here is the ssh debug output. [[email protected] ~]$ ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to hostname.com [::1] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type -1 debug1: identity file /home/user/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_dsa debug1: Server accepts key: pkalg ssh-dss blen 434 Agent admitted failure to sign using the key. debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_rsa debug1: Next authentication method: password [email protected]'s password:

  Read the article

• return a line of grid view in ModalPopupExtender

  - by Meysam Javadi

  hi i use ModalPopupExtender from AjaxControlToolkit to show a panel. my panel have something like this: <asp:Panel ID="pnlSearchPlan" runat="server" style="background-color:#ffffdd;border-width:3px;border-style:solid;border-color:Gray;padding:3px;width:400px;"> <asp:ScriptManager ID="ScriptManager1" runat="server"> </asp:ScriptManager> <cc1:ModalPopupExtender ID="UpdatePanel1_ModalPopupExtender" runat="server" TargetControlID="linkToPopup" PopupControlID="pnlSearchPlan" BackgroundCssClass="ModalBackColor" DropShadow="true" OkControlID="tbnSelect" OnOkScript="onOk()" CancelControlID="btnCancel"> </cc1:ModalPopupExtender> <asp:UpdatePanel ID="UpdatePanel1" runat="server"> <ContentTemplate> <table width="100%" dir="rtl"> <tr> <td >owner</td> <td> <asp:TextBox ID="txtCriteria" runat="server" ></asp:TextBox> <asp:Button ID="btnOk" runat="server" Text="ok" onclick="btnOk_Click" /> <asp:Button ID="tbnSelect" runat="server" Text="select" onclick="tbnSelect_Click" /> <asp:Button ID="btnCancel" runat="server" Text="close" /> </td> </tr> <tr> <td colspan="2"> </asp:RadioButtonList> </td> </tr> <tr> <td colspan="2" align="center"> <pcal:CustomGridView ID="gdvPlan" runat="server" CellPadding="4" ForeColor="Black" GridLines="Vertical" BackColor="White" BorderColor="#DEDFDE" BorderStyle="None" BorderWidth="1px"> <RowStyle BackColor="#F7F7DE" /> <FooterStyle BackColor="#CCCC99" /> <PagerStyle BackColor="#F7F7DE" ForeColor="Black" HorizontalAlign="Right" /> <SelectedRowStyle BackColor="#CE5D5A" Font-Bold="True" ForeColor="White" /> <HeaderStyle BackColor="#6B696B" Font-Bold="True" ForeColor="White" /> <AlternatingRowStyle BackColor="White" /> </pcal:CustomGridView> </td> </tr> </table> </ContentTemplate> </asp:UpdatePanel> </asp:Panel> now want return one cell of gridview after ModalPopupExtender is closed, is this possible without postback? is there any way to return value after close?

  Read the article

• List repositories from multiple projects in Trac using mod_python

  - by Steffen Eriksen

  Currently working on a customized webpage that shows the available projects I have in Trac (1.0.1). I am using mod_python to connect the trac interface. I found a standard page for this, but it didn't show listing of repositories. The page showed some variables to link to the different projects, but I can't find variables to the different repositories inside the projects. I have set up the webpage from reading this: http://trac.edgewall.org/wiki/TracInterfaceCustomization (under Site Appearance) Short summary; editing ../conf.d/trac.conf: PythonOption TracEnvParentDir /parent/dir/of/projects PythonOption TracEnvIndexTemplate /path/to/template And making a template file I can edit at /path/to/template: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:py="http://genshi.edgewall.org/" xmlns:xi="http://www.w3.org/2001/XInclude"> <head> <title>Available Projects</title> </head> <body> <h1>Available Projects</h1> <ul> <dl> <li py:for="project in projects" py:choose=""> <a py:when="project.href" href="$project.href" title="$project.description">$project.name</a> ## <dd> WANT TO ADD CODE HERE! </dd> <py:otherwise> <small>$project.name: <em>Error</em> <br /> ($project.description)</small> </py:otherwise> </li> </dl> </ul> </body> </html> So... The code I want to add is something like: <dd py:for="repos in project.repository" py:choose=""> <a py:when="repos.href" href="$repos.href"> $repos.name</a> </dd> I can't figure out where to add the variables, or if there already exists some variables I can use. After searching through the files it seemed like main.py had something to do with the variables (/usr/local/Trac-1.0.1/trac/web/main.py), but at first look it didn't seem easy to just add more variables. Is there a simple way to find the rest of the variables ? And how hard is it to add more variables? Will it perhaps be easier to do this an alternative way ? All I need is to link to the repositories dynamically

  Read the article

• Proper Imaging Procedures to Restore and Deploy Image with Separate System Reserved Partition

  - by alharaka

  UPDATE: As per my experience here, no one responded. If I do not hear back from TechNet forum members about it, I will post a bounty here, if it makes a difference. I have banged my head against a wall for what seems like all week. I am going to explain my simple procedure, and how none of it, absolutely none, seems to work afterword despite few alternatives and everyone on the internet telling assuming this is how to do it. Diskpart Commands to Create FS Structure REM Select the disk targeted for deployment. REM REM NOTE: Usually disk 0, but drive failure can make it external USB REM media. This will erase the drive regardless! select disk 0 REM Remove previous formatting. clean REM Create System Reserved partition bootloader and files. create partition primary size=100 REM Format the volume format fs=ntfs label="System Reserved" quick override noerr REM Assign the System Reserved partition the D: mount for now assign letter=C REM The main system partition, size not specified to occupy whole drive. create partition primary REM Format the volume format fs=ntfs quick override noerr REM Assign the OS partition the D: mount for now assign letter=D REM Make this the active/bootable partition. sel disk 0 sel partition 1 active REM Close out the diskpart session. exit Now, I thought this was madness, but it turns out the System Reserved partition and standard "System Partition" (C:, commonly both the boot and system volumes where you find the Windows directory AND the bootmgr/ntldr hardware files, this is where Windows 7 diverges) as mounted in the Windows PE session where I run these commands do not matter. See reference here. Since this needs to be BitLocker-ready, enter this crappy System Reserved partition that is separate 100MB of awesome that goes before the regular boot volume. I do this, then I proceed to the next step. Deploy System Reserved and Normal System Images REM C is still the "System Reserved Partition", and the image is just like it sounds. imagex /apply G:\images\systemreserved.wim 1 C: REM D is now what will be the C: system partition on reboot, supposedly. imagex /apply G:\images\testimage.wim 1 D: Reboot the system Now, the images I just captured should look good. This is not even sysprepped, but reapplying the same fscking image I prepared on the same reference workstation hours before. Problem is I get 0xc000000e could not detect the accessible boot device \Windows\system32\winload.exe or different kinds of nonsense revolving around being able to find the boot volume with all the right files. I try different variations of things, now none of them work. I tried repairs with bcdboot, with a fresh System Reserved partition or not, bootrec, and maually editing the damn BCD store with bcdedit. I tried finalizing the above process with and without bootsect /nt60 C: /force. I need to wrap up and automate this procedure. What am I doing wrong that does not make the image happy, but really just miserable.

  Read the article

• How to enable caching on Apache / Ubuntu Linux?

  - by Jim Mischel

  I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

  Read the article

• Arguments for moving from LINQtoSQL to Nhibernate?

  - by sah302

  Backstory: Hi all, I just spent a lot of time reading many of the LINQ vs Nhibernate threads here and on other sites. I work in a small development team of 4 people and we don't even have really any super experienced developers. We work for a small company that has a lot of technical needs but not enough developers to implement them (and hiring more is out of the question right now). Typically our projects (which individually are fairly small) have been coded separately and weren't really layered in anyway, code wasn't re-used, no class libraries, and we just use the LINQtoSQL .dbml files for our pojects, we really don't even use objects but pass around values and stuff, the only time we use objects is when inserting to a database (heck not even querying since you don't need to assign it to a type and can just bind to gridview). Despite all this as I said our company has a lot of technical needs, no one could come to us for a year and we would have plenty of work to implement requested features. Well I have decided to change that a bit first by creating class libraries and actually adding layers to our applications. I am trying to meet these guys halfway by still using LINQtoSQL as the ORM yet and still use VB as the language. However I am finding it a b***h of a time dealing with so many thing in LINQtoSQL that I found easy in Nhibernate (automatic handling of the session, criteria creation easier than expression trees, generic an dynamic querying easier etc.) So... Question: How can I convince my lead developers and other senior programmers that switching to Nhibernate is a good thing? That being in control of our domain objects is a good thing? That being able to implement interfaces is a good? I've tried exlpaining the advantages of this before but it's not understood by them because they've never programmed in a true OO & layered way. Also one of the counter arguments to this I can see is sqlMetal generates those classes automatically and therefore it saves a lot of time. I can't really counter that other than saying spending more time on infrastructure to make it more scalable and flexible is good, but they can't see how. Again, I know the features and advantages (somewhat enough I believe) of each, but I need arguments applicable to my context, hence why I provided the context. I just am not a very good arguer I guess. (Caveat: For all the LINQtoSQL lovers, I may just not be super proficient as LINQ, but I find it very cumbersome that you are required to download some extra library for dynamic queries which don't by default support guid comparisons, and I also find the way of updating entitites to be cumbersome as well in terms of data context managing, so it could just be that I suck hehe.)

  Read the article

• configuring slime in emacs

  - by CodeKingPlusPlus

  I am in the process of configuring slime for emacs. So far I have read about basic functionality for common lisp such as C-c C-q which invokes the command slime-close-parens-at-point which places the proper number of parens where your mouse is. Another command that seemed cool was invoked by C-c C-c and it would pass the code you are editing in a buffer to the REPL, and "compile" it. Why won't these commands work for me? Anyway, I have downloaded slime via M-x list-packages and do not seem to have this functionality (C-h w and then any of these commands tells me that these commands do note exist). So, I saw a bunch of other slime extensions such as slime-repl', 'slime-fuzzy' and 'hippie-expand-slime'. So I again usedM-x list-packages` and downloaded them. Still I did not have these commands. Here is the content of my emacs file relevant to slime: ;;;Common Lisp and Slime (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-20130626.1151") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-repl-201000404") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/hippie-expand-slime-20130226.1656") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-fuzzy-20100404") (require 'slime) (setq slime-lisp-implementations `((sbcl ("/usr/bin/sbcl")) (ecl ("/usr/bin/ecl")) (clisp ("/usr/bin/clisp" "-q -I")))) (require 'slime-repl) (require 'slime-fuzzy) (require 'hippie-expand-slime) When I execute M-x slime I get the following message in the inferior-lisp buffer where I can execute common lisp code (however, shouldn't this be the slime-repl since I required it?): STYLE-WARNING: redefining EMACS-INSPECT (#<BUILT-IN-CLASS T>) in DEFMETHOD STYLE-WARNING: Implicitly creating new generic function STREAM-READ-CHAR-WILL-HANG-P. WARNING: These Swank interfaces are unimplemented: (DISASSEMBLE-FRAME SLDB-BREAK-AT-START SLDB-BREAK-ON-RETURN) ;; Swank started at port: 46533. Then a slime-error buffer is created with the contents: Invalid protocol message: Symbol "CREATE-REPL" not found in the SWANK package. Line: 1, Column: 28, File-Position: 28 Stream: #<SB-IMPL::STRING-INPUT-STREAM {10056B9C33}> (:emacs-rex (swank:create-repl nil) "COMMON-LISP-USER" t 5) How should I modify my emacs file to give me the functionality of those commands? In my emacs file am I not loading the necessary files? Do I need to install an additional package? If you need more information let me know! All help is much appreciated!

  Read the article

• DNS settings for resolving Host name to IP not working?

  - by Hasas Ali Khan

  I want to access my IIS hosted application over LAN. First I installed a DNS server. The DNS configuration steps are: Go to DNS Manager - right click on System Name - click on configure a DNS Server. DNS Server wizard open -, click on next button - Select radio button "forward lookup zone" click on next button. In the second window. click on radio button "The server maintains the zone" and then click next. Give the zone name "example.com" Click on radio button, "Do Not allow dynamic updates". and then click next button. In the next window, click on radio button "No it should not forward query" and then click next button. Complete the configure a DNS server wizard and then click on finish button. After it is managing the DNS records: In DNS server wizard. open tree of forward lookup zone and right click on the new zone name "example.com" - properties and click on "Start of authority" and write values on text boxes serial number=1 primary server=systemname.domainname responsible person=hostmaster.domainname Click on server name, highlight domain name, click on edit button and enter IP address of the server where I host my application. Highlight new zone name and right click on it and click "New Host" option. In this window there are three text boxes: Name(user parent name if blank)=scoring Fully Qualified Domain Name=scoring.example.com IP Address= My IP Address and check on "Create associated pointer(PTR) record" and click on "Add Host" Host button and then click done button. I have host header for my application is "scoring" on port 80 and its working fine on server my application setting are I have change its, Advance setting --> Application Pool Identity --> Local System application can access on server with host name "scoring" but it can not access on machines on LAN. When I change LAN machine host file that is under, C:/windows/system32/driver/etc/host and edit it and enter host name with hosted machine IP like this: scoring 192.168.1.20 By making these changes I can run the application over LAN machines as I mentioned above DNS setting by which I can run App over LAN with out editing the client's host file. What mistake am I doing in this configuration?

  Read the article

• Notepad++: Adding color highlighting for PHP functions?

  - by Jebego

  I've recently begun using Notepad++, and have found a part of its styling functionality that confuses me. I'm currently attempting to color all of PHP's defined functions (such as count(), strlen(), etc.). In the Settings-Style Configurator, you cannot add a new style for such a function list. Instead, I have begun editing the stylers.xml and langs.xml. To add the new coloring, in langs.xml, I've modified the php section to the following: <Language name="php" ext="php php3 phtml" commentLine="//" commentStart="/*" commentEnd="*/"> <Keywords name="instre1">[default keywords]</Keywords> <Keywords name="instre2">[my function list]</Keywords> </Language> The [default keywords] and [my function list] are replaced with wordlists. I've also edited the php section in stylers.xml to look like the following: <LexerType name="php" desc="php" ext=""> <WordsStyle name="QUESTION MARK" styleID="18" fgColor="FF0000" bgColor="FDF8E3" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="DEFAULT" styleID="118" fgColor="000000" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="STRING" styleID="119" fgColor="FF0000" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="STRING VARIABLE" styleID="126" fgColor="FF0000" bgColor="FEFCF5" fontName="" fontStyle="1" fontSize="" /> <WordsStyle name="SIMPLESTRING" styleID="120" fgColor="FF0000" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="WORD" styleID="121" fgColor="008040" bgColor="FEFCF5" fontName="" fontStyle="1" fontSize="" keywordClass="instre1">True False</WordsStyle> <WordsStyle name="NUMBER" styleID="122" fgColor="FF0000" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="VARIABLE" styleID="123" fgColor="0080FF" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="COMMENT" styleID="124" fgColor="FF8040" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="COMMENTLINE" styleID="125" fgColor="FF8040" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="OPERATOR" styleID="127" fgColor="8000FF" bgColor="FEFCF5" fontName="" fontStyle="0" fontSize="" /> <WordsStyle name="FUNCTIONS" styleID="128" fgColor="000080" bgColor="FEFCF5" fontName="" fontStyle="1" fontSize="" keywordClass="instre2"></WordsStyle> </LexerType> The changed part is the last "FUNCTIONS" line. When I restart Notepad++ and go into the Settings-Style Configurator section, under the php language, the FUNCTIONS style exists. I can change the style's color, and can see the entire keyword list under 'Default Keywords'. However, it is not changing the coloring of the words in my code. When I edit the WORD style, which contains stuff like 'if', 'and', and 'true', things change accordingly in my code. Any ideas on how to make this work?

  Read the article

• ASP.NET ObjectDataSource, change CommandName property of FromView Button

  - by Tone

  I have an ObjectDataSource that I'm using with a FormView, and it works fine, but i want to change one small thing. On the FormView the button that fires the update has the CommandName attribute set to "Update," but I would like to change that attribute to something other than "Update" - when I do change that attribute the update no longer works. The reason I want to do this is I have multiple FormViews on the same page and need to have multiple update buttons. Below is my code: FormView: <asp:FormView ID="fvGeneralInfo" runat="server" DataSourceID="objInstructorDetails" CssClass="Gridview" OnItemCommand="fvGeneralInfo_ItemCommand" DefaultMode="Edit"> <EditItemTemplate> <table> .... <tr> <td style="text-align:right;"> <asp:Label runat="server" ID="lblGeneralInfoMessage" Text="General Info updated successfully" Visible="false" /> </td> <td> <asp:Button runat="server" ID="btnUpdateGeneralInfo" ValidationGroup="UpdateGeneralInfo" Text="Update" CommandName="Update" /> <asp:Button runat="server" ID="btnCancelGeneralInfo" Text="Cancel" CommandName="CancelGeneralInfo" /> </td> </tr> </table> </EditItemTemplate> </asp:FormView> ObjectDataSource: <asp:ObjectDataSource ID="objInstructorDetails" runat="server" TypeName="AIMLibrary.BLL.Instructor" SelectMethod="GetInstructorDetails" InsertMethod="InsertInstructor" UpdateMethod="UpdateInstructor" OnInserting="objInstructorDetails_OnInserting" OnUpdating="objInstructorDetails_OnUpdating" > <SelectParameters> <asp:QueryStringParameter Name="InstructorId" QueryStringField="InstructorId" /> </SelectParameters> <UpdateParameters> <asp:Parameter Name="instructorId" Type="Int32" /> <asp:Parameter Name="firstName" Type="String" DefaultValue="" /> <asp:Parameter Name="middleName" Type="String" DefaultValue="" /> <asp:Parameter Name="lastName" Type="String" DefaultValue="" /> <asp:Parameter Name="phone" Type="String" DefaultValue="" /> <asp:Parameter Name="email" Type="String" DefaultValue="" /> <asp:Parameter Name="addressLine1" Type="String" DefaultValue="" /> <asp:Parameter Name="addressLine2" Type="String" DefaultValue="" /> <asp:Parameter Name="city" Type="String" DefaultValue="" /> <asp:Parameter Name="state" Type="String" DefaultValue="" /> <asp:Parameter Name="zip" Type="String" DefaultValue="" /> <asp:Parameter Name="abcBoardNumber" Type="String" DefaultValue="" /> </UpdateParameters> </asp:ObjectDataSource>

  Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >