Search Results

Search found 4786 results on 192 pages for 'traffic shaping'.

Page 167/192 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

• Simple vLAN setup

  - by Logan Bissonnette

  I have a basic lab environment set up to try and get 2 vLANs working in hyper-v. I have the following equipment 1 hyper-v server 1 Desktop PC 1 Managed Switch (d-link DES-3052P) 1 cheap router (DI-604) My end goal is to have 1 VM and the desktop on one vLAN with internet, and 1 VM on a separate vLAN with internet access. I am having troubles getting an internet connection to both vLANs. The switch does not have the ability to have asynchronous vLANs. This is my switch configuration Port 1 - Trunk Port - Connected to router Port 2 - Trunk Port - Connected to hyper-v Server Port 3 - Access Port- Connected to Desktop Within hyper-v I have 1 switch and 2 VMs. When the VMs are set up to use vlan ID 1, everything works fine. As soon as a VM is set up to use vlan ID 2, they lose all network connection and cannot communicate with the router anymore. I believe this is because the router is not vLAN aware. Can anyone help me with what settings need to be set up on my switch? I believe I want an egress rule so traffic leaving towards the router is untagged, is that right? If not, any ideas or hints as to what needs to be set up?

  Read the article

• Finding Bluetooth link key in Windows 7, to double pair a device on dualboot computer

  - by Ilari Kajaste

  How can I dig up the Bluetooth link key for a paired device in Windows 7? Is this something that is dependent on the Bluetooth stack I'm using (Toshiba), or is there a generic place to store these in Windows 7? Note: I'm not talking about the six-digit code usually typed by the user during pairing - that is worthless since it's discarded after pairing process. What I mean is the 128-bit link key that the devices exchange during pairing, and use thereafter to encrypt all their Bluetooth traffic. Background: I dualboot Windows 7 / Ubuntu on my laptop, and I would like to have my phone paired to both OS's. Since the dualbooting computer has only one Bluetooth adapter and thus only one Bluetooth address, I cannot do two pairings to the phone, since on the second pairing (Windows) the phone just replaces the previous pairing (Linux) to the same Bluetooth address. A thread on Ubuntu forums pointed me to what I have to do - pair first on Linux, then on Windows, and then replace the link key on Linux side with the one Windows negotiated. I can find the Linux side pairing key from /var/lib/Bluetooth/[BD_ADDR]/linkkeys - no problems there. However, on Windows side I can't find the key. According to the forum post, on Windows side the key should be in SYSTEM\ControlSet002\services\BTHPORT\Parameters\Keys\[BD_ADDR] but while that registry key does exist, it has no subkeys. (And a similar registry path in ControlSet001 didn't have any subkeys either.) One thing I've been instructed to do is to capture all events during pairing with Sysinternals Process Monitor. I did this, but I haven't been able to find any useful information from the captured events, not even by exporting the data to a huge XML and grepping that with the BD_ADDRs (with or without colons). So how could I find the link key for a paired device in Windows 7? Some reference information: Wikipedia: Bluetooth, Security Now: Bluetooth security

  Read the article

• When should NTPd broadcast/broadcastclient be used instead of client/server or peer modes?

  - by Luke404

  The NTP deamon if often used in its simplest mode, which is client/server: you specify one or more server directives in your ntp.conf and your clients will use those servers. In addition to that, when you run your own NTP servers, it is good practice to peer them together, so if one of them looses connectivity to its upstream servers, it will get time from its peers. But NTPd can also work with broadcast and/or multicast distribution of time data, with the documentation stating: broadcast and multicast modes are intended for configurations involving one or a few servers and a possibly very large client population The documentation also says elsewhere: It is possible and frequently useful to configure a host as both broadcast client and broadcast server. A number of hosts configured this way and sharing a common broadcast address will automatically organize themselves in an optimum configuration based on stratum and synchronization distance. I can see one obvious administrative benefit: you don't have to manually specify and update your list of NTP servers in the clients ntp.conf, so to me it looks tempting to use broadcast mode even for a small client population (say 5+ clients with 3~4 servers). I expect network traffic to be a little higher with broadcasts instead of client/server associations, but given the usual gigabit ethernet LAN the impact should be negligible unless you have a very very large number of hosts in the same broadcast domain. At the end of the day, when should broadcast mode be used or avoided? Are there pros and cons I haven't seen?

  Read the article

• Proxy auto-config dnsResolve doesn't seem to resolve subdomains

  - by HorusKol

  We're running on a Windows domain, and have a DNS to control computer names on our intranet. The following PAC works great for basic hostnames on our intranet - but we're setting up some subdomain-like names (example, redesign.buildbox), and it isn't resolving these. These subdomains are resolvable through other means (such as nslookup). Other than checking to see if the host has ".buildbox" or other domain, is there a way to make it work? Maybe I could try appending the Windows domain to host (can you concatenate strings in a PAC)? function FindProxyForURL(url, host) { // If IP address is internal or hostname resolves to internal IP, send direct. var resolved_ip = dnsResolve(host); if (isInNet(resolved_ip, "129.2.2.0", "255.255.255.128")) return "DIRECT"; if (isInNet(resolved_ip, "10.1.1.0", "255.255.255.0")) return "DIRECT"; if (isInNet(resolved_ip, "150.1.2.0", "255.255.255.248")) return "DIRECT"; // All other traffic uses below proxies, in fail-over order. return "PROXY 192.111.222.111:8080; DIRECT"; }

  Read the article

• Performance data collection for short-running, ephemeral servers

  - by ErikA

  We're building a medical image processing software stack, currently hosted on various AWS resources. As part of this application, we have a handful of long-running servers (database, load balancers, web application, etc.). Collecting performance data on those servers is quite simple - my go-to- recipe of Nagios (for monitoring/notifications) and Munin (for collection of performance data and displaying trends) will work just fine. However - as part of this application, we are constantly starting up and terminating compute instances on EC2. In typical usage, these compute instances start up, configure themselves, receive a job from a message queue, and then get to work processing that job, which takes anywhere from 15 minutes to over 8 hours. After job completion, these instances get terminated, never to be heard from again. What is a decent strategy for collecting performance data on these short-lived instances? I don't necessarily need monitoring on them - if they fail for whatever reason, our application will detect this and handle re-starting the job on another instance or raising the flag so an administrator can take a look at things. However, it still would be useful to collect information like CPU (user, idle, iowait, etc.), memory usage, network traffic, disk read/write data, etc. In our internal database, we track the instance ID of the machine that runs each job, and it would be quite helpful to be able to look up performance data for a specific instance ID for troubleshooting and profiling. Munin doesn't seem like a great candidate, as it requires maintaining a list of munin nodes in a text file - far from ideal for an environment with a high amount of churn, and for the short amount of time each node will be running, I'd rather keep the full-resolution data indefinitely than have RRD water down the data over time. In the end, my guess is that this will require a monitoring engine that: uses a database (MySQL, SQLite, etc.) for configuration and data storage exposes an API for adding/removing hosts and services Are there other things I should be thinking about when evaluating options? Perhaps I'm over-thinking this, though, and just ought to run sar at 1-minute intervals on these short-lived instances and collect the sar db files prior to termination.

  Read the article

• Router reporting failed admin login attempts from home server

  - by jeffora

  I recently noticed in the logs of my home router that it relatively regularly lists the following entry: [admin login failure] from source 192.168.0.160, Monday, June 20,2011 18:13:25 192.168.0.160 is the internal address of my home server, running Windows Home Server 2011. Is there anyway I can find out what specifically is trying to login to the router? Or is there some explanation for this behaviour? (not sure if this belongs here or on superuser...) [Update] I've run both Wireshark and netmon for a while on my home server. Wireshark captured the traffic, but didn't really show anything useful (or nothing I could make use of). A simple HTTP GET request is sent from the server (192.168.0.160) to the router (192.168.0.1), from a seemingly random port (I've seen examples from 50068, 52883), and it appears to do it twice in quick succession (incrementing port by 1), about every hour. Running netstat around the time of the failure didn't show anything (probably too long after anyway). I tried using netmon as it categorises by process, so I thought it might show a corresponding process for the port. Unfortunately, this comes in under the 'unknown' category, meaning it's basically just a slower, less useful Wireshark. I know there's not much to go on here, but does this help in anyway?

  Read the article

• Slow browsing through IE on Windows Server 2012

  - by Volodymyr

  We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

  Read the article

• Windows VPN always disconnects after < 3 minutes, only from my network

  - by hemp

  First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

  Read the article

• what are valid 'ack' values?

  - by WileECanisLatrans

  having an issue with a vendor who claims the cause of a problem is an invalid 'ack' value in the tcp data. I'm using java so I didn't write this layer. I used snoop to capture the traffic on the wire and am using wireshark to display the data. Here is what is happening. After receiving a multi-packet(5) message I see a multi-pack(3) response. The first packet in the response has a value for 'ack' that is different than the 'ack' value in the other two packets. The vendor claims this data is suspect. I've provided sample data below. I'm not a tcp expert so I don't know if this is a problem or not. I've tried to find something on valid ack values and it seems to me the value should be 80018 but that doesn't mean the 78345 is wrong. I found this on the web and it seems to apply but I'm not sure: "the ack value of any data segment is considered valid as long as it does not acknowledge data ahead of the next segment to send". Thanks for your help. My understanding is the vendor has written their own tcp layer. * source seq ack len * vendor 75465 10924 0 * vendor 75465 10924 1440 * vendor 76905 10924 1440 * vendor 78345 10924 1440 * vendor 79785 10924 233 * me 10924 78345 0 * me 10924 80018 0 * me 10924 80018 197

  Read the article

• Painless deployment of a Django app (port from Drupal). Do I have to switch to a VPS?

  - by Monden

  I'm about to complete porting my Drupal based community site to Django. My Drupal site is hosted at a shared hosting (Dreamhost) for last 4 years, and stability & performance has been satisfactory. The site gets around 5k unique visitors with 70-80k page views a day. This will be my first deployment of a Django application and I'm not comfortable with managing my own VPS. I use Ubuntu as a dev. server, but I don't have experience with it at the production env. I have an unrelated internal CRM app (Django) that I host with Webfaction. However security and performance isn't an issue as it's only accessed by 5 people. Unfortunately, I don't have much time to learn and maintain a VPS at this moment. I would like to know if I can host a site with this much traffic at Webfaction's shared environment? How would performance differ in comparison to Linode or Slicehost? Google AppEngine isn't an option at the moment as I'll be using my current Postgresql database.

  Read the article

• which virtualization technology is right for me?

  - by Chris

  I need a little help with this getting this sorted out. I want to setup a linux virtual server that I can use to run both sever and desktop systems. I want a linux system that is minimalist in nature as all the main os will be doing is acting as a hypervisor. The system I'm trying to setup will be running a file server, windows 7, ubuntu 10.04, windows xp and a firewall/gateway security system. All the client OS'es accessing and storing files on the file server. Also all network traffic will be routed through the gateway guest os. The file sever will need direct disk access while the other guests can run one disk images. All of this will be running on the same computer so I wont be romoting in to access the guests OS'es. Also if possible I would like to be able to use my triple head setup in the guest OS'es. I've looked at Xen, kvm and virtualbox but I don't know which is the best for me. I'm really debating between kvm and virtual box as kvm seem to support direct hardware access.

  Read the article

• How to minimize the risk of employees spreading critical information?

  - by Industrial

  Hi everyone, What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

  Read the article

• trying to route between two openvpn clients

  - by user42055

  I have two openvpn clients on the 10.0.1.0 (client1) and 192.168.0.0 (client2) subnets with the server's openvpn connection having the ip 192.168.150.1 The server has ip forwarding enabled. Currently, client1's vpn ip is 192.168.150.10 and the P-t-P ip is 192.168.150.9 I have created the following static route on client1: route add -net 10.0.1.0 netmask 255.255.255.0 gw 192.168.150.9 The routing table on client1 looks like this: Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.150.1 192.168.150.9 255.255.255.255 UGH 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 I thought this would be correct to allow traffic from client1 to reach computers on client2's network, but it does not work. Is 192.168.150.9 (the P-t-P address) the correct one to be routing through ? I tried using 192.168.150.1 but I couldn't create the route. I hope this is clear.

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• pptp server 2003 hands out gateway from nic not dhcp server

  - by Pete

  I have created a pptp RRAS server for a handful of clients to connect to. I would like them to use the servers default gateway (.1) for internet access. They are able to successfully connect (& see LAN) but it then cuts them off the internet. I understand that all internet traffic would be routed through the pptp server but that's ok since I have enough pipe. The problem seems to be that: the clients gateway shows as their assigned RAS ip. The clients assigned DNS settings seem to be what is set to the servers nic not what I have specified in dhcp (which is the same server). DHCP relay agent properties points to the nic DHCP is running on (192.168.100.163). .1 is gateway in nic hw properties & dhcp. I have different dns secondary & third entries on my nic properties than what dhcp is configured for. The problem is that I have a 10.10.1.x network that people can not see if they uncheck the gateway option but, they are then unable to see our other hosted sites on the internet.

  Read the article

• dom0 enable IPv6 for guests

  - by user98651

  I am looking at deploying IPv6 to my virtual machines. Right now I have v6 working great on the dom0 using a 6in4 provided by Hurricane Electric as I do not have native v6. However, I would like to distribute some of the /48 I am receiving to the domUs (/64 per machine would be ideal, but I am open to your suggestions). Static configuration on the domU side is fine. All I want to accomplish is getting the traffic to pass through the dom0 to the domU. To say the least, I'm still trying to wrap my head around all the virtual interfaces and bridges Xen creates. Yes, I have Googled around for this a bit and have not found anything great. I tried using two "vif-route6" bash scripts with no luck (possibly due to my ignorance with Xen networking). I am still stuck (mainly in how to configure the dom0). I would like to imagine this problem is relatively easy to solve and I look forward to your suggestions and help! Edited post to clarify my end goal: getting IPv6 to domU guests. I am completely open to suggestions but am hoping for something other than setting up a tunnel for every guest.

  Read the article

• Windows/IIS Hosting :: How much is too much?

  - by bsisupport

  I have 4 Windows 2003 servers running IIS 6. These servers host a bunch of unique web sites (in that they are all different in build/architecture/etc). The code behind these sites range from straight HTML, classic ASP, and 1.1/2.0/3.x flavors of .NET. Some (most) of the sites use a SQL backend, which is hosted on one or two different servers – not the IIS servers themselves. No virtualization on these servers and no load balancing for these particular sites. The problem I’m running into is coming up with some baseline metrics to determine, or basically come up with a “baseline score” to know when a web server has reached its hosting limit. Today, some basic information about each server is used: how much bandwidth does the server pump out, hard drive space availability, and basic (very basic) RAM & CPU utilization (what it looks like at peak traffic times.) I would be grateful if those of you that are 1000x smarter than I am could indulge me with your methods of managing IIS environments. Whether performance monitoring specifics, “score” determination as I’m trying to determine, or the obvious combination of both. Thanks in advance.

  Read the article

• Requests are making it to my app server, but not into node.js -- why?

  - by Zane Claes

  I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

  Read the article

• LDAP SSL connect problem

  - by juergen

  I set up a test domain for my LDAP SSL tests and it is not working. I am using Windows Server 2008 R2 SP 1. I came so far: 1. i generated and installed my self signed certificate on the test domain controller 2. on the server i can log into ldap over SSL with the MS ldp.exe tool. 3. using ldp.exe on a client that is no in this domain the login fails with error 0x51 = "failed to connect". (i don't have a client computer that is in this domain right now) 4. I testet the certificate by using it in the IIS on the test server and I can reach the default page of the test server over SSL. (from the client that is not in the domain) 5. analysing the traffic between client and server I can see that the server is sending a certificate to the client. why isn't this working on my client computer?

  Read the article

• In APC+PHP, how much RAM is too much? Is it okay to set apc.shm_size to many GB?

  - by Jeremy Clarke

  On our server we have a LOT of RAM for our traffic levels (16GB). The HTTP processes regularly eat up all CPU and need to be restarted without even getting close to using swap memory, so I'm looking for ways to spend RAM to ease the load on Apache (and/or help the seperate MySQL server which may be breaking Apache). I have many WordPress installs on the HTTPD instance so APC sometimes uses as much as 900MB of ram (according to the apc.php charts). Just in case I have apc.shm_size set to 1600MB which is more than it needs but not more than I can spare. This means there is usually lots of extra RAM available to APC but also very little turnover and fragmentation is never more than 1%. Is this dangerous? Should I be slimming down APC to less than 1GB just on principle? Should I be expecting some turnover within APC in the name of bringing it's overall footprint down? Having so much memory devoted to APC means that in top/htop every single httpd process shows ~1.9GB in the VIRT memory column. Obviously this is shared memory and not used per-process, but could it be hurting our server? NOTE: The problem with the server remains unclear but the effect is that about 60 times a day all 8 CPU's fill up to 100% and everything stops working until Monit sees that Apache is broken and restarts it (Monin also saves the MySQL server). I'm not sure if APC is even part of the problem but I'm trying to optimize everything just in case.

  Read the article

• iTunes Home Sharing only works one way between 2 Windows XP PC's on the same LAN

  - by scunliffe

  Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the Windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

  Read the article

• openvpn port 53 bypasses allows restrictions ( find similar ports)

  - by user181216

  scenario of wifi : i'm using wifi in hostel which having cyberoam firewall and all the computer which uses that access point. that access point have following configuration default gateway : 192.168.100.1 primary dns server : 192.168.100.1 here, when i try to open a website the cyberoam firewall redirects the page to a login page (with correct login information, we can browse internet else not), and also website access and bandwidth limitations. once i've heard about pd-proxy which finds open port and tunnels through a port ( usually udp 53). using pd-proxy with UDP 53 port, i can browse internet without login, even bandwidth limit is bypassed !!! and another software called openvpn with connecting openvpn server through udp port 53 i can browse internet without even login into the cyberoam. both of softwares uses port 53, specially openvpn with port 53, now i've a VPS server in which i can install openvpn server and connect through the VPS server to browse internet. i know why that is happening because with pinging on some website(eb. google.com) it returns it's ip address that means it allows dns queries without login. but the problem is there is already DNS service is running on the VPS server on port 53. and i can only use 53 port to bypass the limitations as i think. and i can not run openvpn service on my VPS server on port 53. so how to scan the wifi for vulnerable ports like 53 so that i can figure out the magic port and start a openvpn service on VPS on the same port. ( i want to scan similar vulnerable ports like 53 on cyberoam in which the traffic can be tunneled, not want to scan services running on ports). improvement of the question with retags and edits are always welcomed... NOTE : all these are for Educational purpose only, i'm curious about network related knowledge.....

  Read the article

• openvpn port 53 bypasses allows restrictions ( find similar ports)

  - by user181216

  scenario of wifi : i'm using wifi in hostel which having cyberoam firewall and all the computer which uses that access point. that access point have following configuration default gateway : 192.168.100.1 primary dns server : 192.168.100.1 here, when i try to open a website the cyberoam firewall redirects the page to a login page (with correct login information, we can browse internet else not), and also website access and bandwidth limitations. once i've heard about pd-proxy which finds open port and tunnels through a port ( usually udp 53). using pd-proxy with UDP 53 port, i can browse internet without login, even bandwidth limit is bypassed !!! and another software called openvpn with connecting openvpn server through udp port 53 i can browse internet without even login into the cyberoam. both of softwares uses port 53, specially openvpn with port 53, now i've a VPS server in which i can install openvpn server and connect through the VPS server to browse internet. i know why that is happening because with pinging on some website(eb. google.com) it returns it's ip address that means it allows dns queries without login. but the problem is there is already DNS service is running on the VPS server on port 53. and i can only use 53 port to bypass the limitations as i think. and i can not run openvpn service on my VPS server on port 53. so how to scan the wifi for vulnerable ports like 53 so that i can figure out the magic port and start a openvpn service on VPS on the same port. ( i want to scan similar vulnerable ports like 53 on cyberoam in which the traffic can be tunneled, not want to scan services running on ports). improvement of the question with retags and edits are always welcomed... NOTE : all these are for Educational purpose only, i'm curious about network related knowledge.....

  Read the article

• Remote Desktop fails after VPN connection

  - by Samet Sorgut

  The local computer (comp 1) is connected to a remote computer (comp 2) with Remote Desktop. On the remote computer (comp 2), I try to establish an VPN connection to a different remote computer (comp 3). Once I try to establish the VPN connection from the remote computer (comp 2) to the second remote computer (comp 3), Remote Desktop freezes on comp 1. It is not possible to connect to comp 2 again via Remote Desktop. What can be done to connect to this remote computer (comp 2) after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest? EDIT: I want to use the internet connection of the VPN, so all traffic should go over the VPN but still RDP working. My IP: 100.0.0.1 The IP where I'm connecting via RDP: 200.0.0.20 (Mask: 255.255.255.192, Gateway: 200.0.0.193) Where the 200.0.0.1 connects to VPN the IP of the VPN is: 65.254.61.250 Will routing like this help (Command is issued in 200.0.0.20, the RDP location): route ADD 65.254.61.250 MASK 255.255.255.192 200.0.0.193 Couldn't add gives the error: The route addition failed: The parameter is incorrect. I tried before connecting to VPN.

  Read the article

• Developing high-performance and scalable zend framework website [on hold]

  - by Daniel

  We are going to develop an ads website like http://www.gumtree.com/ (it will not be like this one but just to give you an ideea) and we are having some issues regarding performance and scalability. We are planning on using Zend Framework for this project but this is all that I'm sure off at this point. I don't think a classic approch like Zend Framework (PHP) + MySQL + Memcache + jQuery (and I would throw Doctrine 2 in there to) will fix result in a high-performance application. I was thinking on making this a RESTful application (with Zend Framework) + NGINX (or maybe MongoDB) + Memcache (or eAccelerator -- I understand this will create problems with scalability on multiple servers) + jQuery or maybe throw Backbone.js in there, a CDN for static content, a server for images and a scalable server for the requests and the rest. My questions are: - What do you think about my approch? - What solutions would you recommand for developing an high performance, scalable application expected to have a lot of traffic using PHP(Zend Framework 2)...I would be interested in your approch. I should note that I'm a Zend developer, I'm working with Zend for over 3 years, this is why I'm choosing it.

  Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >