Search Results

Search found 5346 results on 214 pages for 'before filter'.

Page 169/214 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

  • iptables : how to allow incoming ftp traffic?

    - by logansama
    Hi, Still fighting my way through the jungle that is called iptables. I have managed to allow FTP access outside of our LAN: both these would work. NOTE: eth0 is the LAN interface and eth1 is the WAN interface. iptables -t filter -A FORWARD -i eth0 -p tcp --dport 20:21 -j ACCEPT or iptables -A FORWARD -i eth0 -o eth1 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But when i connect to a external FTP server i manage to log in and all is fine until it wishes to List the directory content. Then nothing happens as the data is blocked, due to the fact that i do not have a rule set up to allow it! (my last rule on the FORWARD chain is to block all traffic) I have tried a gazillion rules (many of which i did not understand) to try and allow the FTP traffic back through my server. One such rule for example was: iptables -A FORWARD -i eth1 -o eth0 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But i cannot get the List to work. It just times out after a while. Would anyone perhaps know how to build a rule which would allow FTP to List / allow such traffic back? Or have a link to sources i could work through? Thank you,

    Read the article

  • Problems forwarding port 3306 on iptables with CentOS

    - by BoDiE2003
    Im trying to add a forward to the mysql server at 200.58.126.52 to allow the access from 200.58.125.39, and Im using the following rules (its my whole iptables of the VPS of my hosting). I can connect locally at the server that holds the mysql service as localhost, but not from outside. Can someone check if the following rules are fine? Thank you # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp -s 200.58.125.39 --dport 3306 -j ACCEPT -A INPUT -p tcp -s 200.58.125.39 --sport 1024:65535 -d localhost --dport 3306 -m state --state NEW,ESTABLISHED -j ACCEPT -A OUTPUT -p tcp -s localhost --sport 3306 -d 200.58.125.39 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT COMMIT And this is the output of the connection trial. [root@qwhosti /home/qwhosti/public_html/admin/config] # mysql -u user_db -p -h 200.58.126.52 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on '200.58.126.52' (113)

    Read the article

  • OpenVPN server will not redirect traffic

    - by skerit
    I set up an OpenVPN server on my VPS, using this guide: http://vpsnoc.com/blog/how-to-install-openvpn-on-a-debianubuntu-vps-instantly/ And I can connect to it without problems. Connect, that is, because no traffic is being redirected. When I try to load a webpage when connected to the vpn I just get an error. This is the config file it generated: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca ca.crt cert server.crt key server.key dh dh1024.pem push "route 10.8.0.0 255.255.255.0" push "redirect-gateway" comp-lzo keepalive 10 60 ping-timer-rem persist-tun persist-key group daemon daemon This is my iptables.conf # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *raw :PREROUTING ACCEPT [37938267:10998335127] :OUTPUT ACCEPT [35616847:14165347907] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *nat :PREROUTING ACCEPT [794948:91051460] :POSTROUTING ACCEPT [1603974:108147033] :OUTPUT ACCEPT [1603974:108147033] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth1 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j MASQUERADE COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *mangle :PREROUTING ACCEPT [37938267:10998335127] :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616847:14165347907] :POSTROUTING ACCEPT [35680187:14169930490] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *filter :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616848:14165347947] -A INPUT -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A FORWARD -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 -A FORWARD -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A OUTPUT -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 COMMIT # Completed on Sat May 7 13:09:44 2011

    Read the article

  • tftpd starts randomly

    - by Mutant
    A few days ago my Little Snitch filter starts popping up tftpd. I'd never seen this before, so I immediately start freaking out thinking my Mac has been compromised. I can't find anything unusual on the system. The process usually dies before I can trace it (little snitch never allowed the connection just left the popup up). I finally caught it once, and found this: [10:32]: sudo lsof -nlP | fgrep tftp Password: tftpd 1924 18446744 cwd DIR 1,3 1326 2 / tftpd 1924 18446744 txt REG 1,3 29856 163979456 /usr/libexec/tftpd tftpd 1924 18446744 txt REG 1,3 600576 163686622 /usr/lib/dyld tftpd 1924 18446744 txt REG 1,3 303300608 189014898 /private/var/db/dyld/dyld_shared_cache_x86_64 tftpd 1924 18446744 0u IPv4 0x34a76100fcbb06e3 0t0 UDP *:55818 tftpd 1924 18446744 2u IPv4 0x34a76100f1113c53 0t0 UDP *:69 [10:32]: ps ax | fgrep 1924 1924 ?? S 0:00.00 /usr/libexec/tftpd -i /private/tftpboot 1949 s000 S+ 0:00.00 fgrep 1924 For the life of me I can't figure out what is starting this. Nothing in cron, launchdaemons, etc. Google searches haven't yielded much either. The connection IP is different each time. So my question is: Has anyone seen anything like this before?

    Read the article

  • What's a good solution for file-tagging in linux?

    - by julien
    I've been looking for a way to tag my files and search/filter them based on those tags. Here are my (updated) requirements : any file readable by the user can be tagged freely a user can search for files matching one or several tags files can be moved around without losing the previously associated tags the system could be backed up easily no dependencies on any desktop environment if any gui is involved, there must be a cli fallback I've been hoping for some basic filesystem & coreutils hackery to handle this, but I haven' thought about this hard enough yet. Meanwhile I'll review beagle and metatracker, which have been mentionned here, and see how they perform. Ok so beagle has huge gnome dependencies, and tracker is okish, but still has some dependencies I don't like... Been doing some more research, and the way to go could very well be extended file attributes. That's a native solution for most recent filesystems, but they aren't very well supported yet (most coreutils destroys them by default, cp for example needs the -a flag to preserve them). Would like to hear some thoughts on using them while I try my hand at some hacks myself, eventhough this might warrant a new question.

    Read the article

  • How to quickly check if two columns in Excel are equivalent in value?

    - by mindless.panda
    I am interested in taking two columns and getting a quick answer on whether they are equivalent in value or not. Let me show you what I mean: So its trivial to make another column (EQUAL) that does a simple compare for each pair of cells in the two columns. It's also trivial to use conditional formatting on one of the two, checking its value against the other. The problem is both of these methods require scanning the third column or the color of one of the columns. Often I am doing this for columns that are very, very long, and visual verification would take too long and neither do I trust my eyes. I could use a pivot table to summarize the EQUAL column and see if any FALSE entries occur. I could also enable filtering and click on the filter on EQUAL and see what entries are shown. Again, all of these methods are time consuming for what seems to be such a simple computational task. What I'm interested in finding out is if there is a single cell formula that answers the question. I attempted one above in the screenshot, but clearly it doesn't do what I expected, since A10 does not equal B10. Anyone know of one that works or some other method that accomplishes this?

    Read the article

  • ADSL2+ - High sync-rate, good line attenuation, but low noise margin and slow speeds

    - by Mark Pim
    I've been with my ISP (IdNet) for a few months and have been getting some good speeds, but in the last week the speed has dramatically decreased (from 15 Mbps+ to around 0.2 Mbps). This happens at all times of day, not just peak periods. Obviously I've done all I can to isolate problems my end - only one PC is connected to the router (via ethernet cable) and no other background programs are using the network etc. I've raised the issue with the ISP and they've suggested trying a new ADSL filter to see if that is casuing the problem, but I thought it would also be good to get the opinion of superuser on possible causes or other troubleshooting I can do. Here are the juicy stats :) My router (Netgear DGN1000) reports: Downstream Upstream Connection Speed 17602 kbps 1062 kbps Line Attenuation 17.9 db 8.6 db Noise Margin 6.0 db 6.1 db I used RouterStats and it seems to show those figures stay fairly consistent all the time I ran the BT speedtest and it reported: download speed of 164 kbps, out of a max achievable of 21000 kbps upload speed of 859 kbps, out of 1048 kbps DSL connection rate 17719 kbps down and 1048 kbps up IP Profile of 15000 kbps Is there any more troubleshooting I can do? Does this look like a problem with my equipment / wiring or with BT's line? Any advice would be great :)

    Read the article

  • Strange File-Server I/O Spikes - What Is Causing This?

    - by CruftRemover
    I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

    Read the article

  • Steps to debugging web site latency and timeout issues

    - by Paperjam
    I have a client who has multiple offices around the country, all of which share the same Internet connection via their WAN. One specific office for this client is experiencing severe latency and timeout issues with my web site. Most, but not all, of the latency occurs on a specific ASPX page where multiple postbacks are made while populating cascading dropdown lists (rapid form submits). The latency is sporadic and can be anywhere from a few seconds to a full timeout. There is no indication that the timeouts are occurring on the server's end. The IT guy for this client is having trouble narrowing down the problem. Since it is affecting only one location for one client, I am led to believe it is not something with my site but something specific to that location. He's measured ping times while using the site and has noticed no real variance in ping times even when the page has timed out. I believe this may be being caused by some sort of Internet filter that doesn't like rapid form submits, but beyond a hunch I haven't a clue. My question is what things should I tell the IT guy to look for? While I'm not trying to provide active tech support for this issue, I would at least like to glean an understanding of what is going on and try to offer some sort of advice. Thank you.

    Read the article

  • Strategy for Incremental Datasource fetchings in Excel

    - by user1352530
    I am in an scenario with a table that is refresh by a third app every week. I need to keep accumulating all data in Excel, using an ODBC connection to the database. I am wondering Approach 1: Is there a way to force Excel to append results for every update (this update would be triggered according to a parameter that indicates week)? I tried to define the table for which the connection loads using a dynamic reference but once is anchored first time, table position is never redefined Approach 2: Use an ETL to accumulate all weekly results into a staging table and then connect Excel to it in real time. But, I would need a mechanism for caching old data, as I cannot grow exponentially the time Excel opens. Imagine after 10 years, Excel would need to update at opening 10 years fo data before showing it. Is there a way to store already fetched data and increment it at real time (when book is opened) by selecting new data (with a query/filter of something) Thanks EDIT: Maybe it's better to ask it that way: What is the optimal strategy for a table that keeps growing and needs to be read in real time by Excel? I just don't want to fetch absolutely all data after some months...

    Read the article

  • Possible for linux bridge to intercept traffic?

    - by A G
    I have a linux machine setup as a bridge between a client and a server; brctl addbr0 brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1 0.0.0.0 ifconfig eth2 0.0.0.0 ip link set br0 up I also have an application listening on port 8080 of this machine. Is it possible to have traffic destined for port 80 to be passed to my application? I have done some research and it looks like it could be done using ebtables and iptables. Here is the rest of my setup: //set the ebtables to pass this traffic up to ip for processing; DROP on the broute table should do this ebtables -t broute -A BROUTING -p ipv4 --ip-proto tcp --ip-dport 80 -j redirect --redirect-target DROP //set iptables to forward this traffic to my app listening on port 8080 iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 8080 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1/1 //once the flows are marked, have them delivered locally via loopback interface ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 //enable ip packet forwarding echo 1 > /proc/sys/net/ipv4/ip_forward However nothing is coming into my application. Am I missing anything? My understanding is that the target DROP on the broute BROUTING chain will push it up to be processed by iptables. Secondly, are there any other alternatives I should investigate? Edit: IPtables gets it at nat PREROUTING, but it looks like it drops after that; the INPUT chain (in either mangle or filter) doesn't see the packet.

    Read the article

  • Save and restore multiple layers within a Photoshop action that flattens

    - by SuitCase
    I'm editing comic pages with layers - "background", "foreground", "lineart" and "over lineart". I have a Photoshop action that includes a Mode-Bitmap command, which requires the image to be flattened. I need this part of the action because I use the Halftone Screen method of reducing the greyscale image to bitmap on the "background" layer, creating a certain effect. I am pretty sure there is no filter or anything else that gives the same effect. After the mode is changed to bitmap, my action changes things back to greyscale for further changes. This poses a problem. I only want to do the bitmap mode change on the background layer, and after I do the change I want to restore the layer structure as it was - with the foreground, lineart and over lineart layers back above the now-halftoned background. My current method of saving these layers and restoring them is clumsy. My action is able to automatically save the "foreground" layer by selecting it, cutting it, then pasting it back in after the mode changing is over. But, for the "ink" and "over ink" layers, I have to manually cut these layers, paste them into a new document, and later re-cut and re-paste after running my action. This is so clunky! What I would like to know is if it's possible to set aside my layers in an automated way, and then bring them back in, also in an automated way. An ugly (but functional) solution would be to replicate my actions of creating new documents and pasting them temporarily there, but I don't think Photoshop allows you to do things outside of your current document with an action. It seems to me that the only way to do what I want is to use the "hack" of incorporating the clipboard into the action as a clever hack, but that leaves me stuck as I have two more layers that can't fit onto that same clipboard. Help or suggestions would be appreciated. I can keep on doing it manually, but to have a comprehensive action would save me a ton of time.

    Read the article

  • SNMP query - operation not permitted

    - by jperovic
    I am working on API that reads a lot of data via SNMP (routes, interfaces, QoS policies, etc...). Lately, I have experienced a random error stating: Operation not permitted Now, I use SNMP4J as core library and cannot really pinpoint the source of error. Some Stackoverflow questions have suggested OS being unable to open sufficient number of file handles but increasing that parameter did not help much. The strange thing is that error occurs only when iptables is up and running. Could it be that firewall is blocking some traffic? I have tried writing JUnit test that mimicked application's logic but no errors were fired... Any help would be appreciated! Thanks! IPTABLES *nat :PREROUTING ACCEPT [2:96] :POSTROUTING ACCEPT [68:4218] :OUTPUT ACCEPT [68:4218] # route redirect za SNMP Trap i syslog -A PREROUTING -i eth0 -p udp -m udp --dport 514 -j REDIRECT --to-ports 33514 -A PREROUTING -i eth0 -p udp -m udp --dport 162 -j REDIRECT --to-ports 33162 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT ..... # SNMP -A INPUT -p udp -m state --state NEW -m udp --dport 161 -j ACCEPT # SNMP trap -A INPUT -p udp -m state --state NEW -m udp --dport 162 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 33162 -j ACCEPT ..... -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT

    Read the article

  • Enabling http access on port 80 for centos 6.3 from console

    - by Hugo
    Have a centos 6.3 box running on Parallels and I'm trying to open port 80 to be accesible from outside tried the gui solution from this post and it works, but I need to get it done from a script. Tried to do this: sudo /sbin/iptables -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT sudo /sbin/iptables-save sudo /sbin/service iptables restart This creates exactly the same iptables entries as the GUI tool except it does not work: $ telnet xx.xxx.xx.xx 80 Trying xx.xxx.xx.xx... telnet: connect to address xx.xxx.xx.xx: Connection refused telnet: Unable to connect to remote host UPDATE: $ netstat -ntlp (No info could be read for "-p": geteuid()=500 but you should be root.) Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:6379 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:37439 0.0.0.0:* LISTEN - tcp 0 0 :::111 :::* LISTEN - tcp 0 0 :::22 :::* LISTEN - tcp 0 0 ::1:631 :::* LISTEN - tcp 0 0 :::60472 :::* LISTEN - $ sudo cat /etc/sysconfig/iptables # Generated by iptables-save v1.4.7 on Wed Dec 12 18:04:25 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [5:640] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT # Completed on Wed Dec 12 18:04:25 2012

    Read the article

  • Allow outgoing connections for DNS

    - by Jimmy
    I'm new to IPtables, but I am trying to setup a secure server to host a website and allow SSH. This is what I have so far: #!/bin/sh i=/sbin/iptables # Flush all rules $i -F $i -X # Setup default filter policy $i -P INPUT DROP $i -P OUTPUT DROP $i -P FORWARD DROP # Respond to ping requests $i -A INPUT -p icmp --icmp-type any -j ACCEPT # Force SYN checks $i -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Drop all fragments $i -A INPUT -f -j DROP # Drop XMAS packets $i -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # Drop NULL packets $i -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # Stateful inspection $i -A INPUT -m state --state NEW -p tcp --dport 22 -j ACCEPT # Allow established connections $i -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow unlimited traffic on loopback $i -A INPUT -i lo -j ACCEPT $i -A OUTPUT -o lo -j ACCEPT # Open nginx $i -A INPUT -p tcp --dport 443 -j ACCEPT $i -A INPUT -p tcp --dport 80 -j ACCEPT # Open SSH $i -A INPUT -p tcp --dport 22 -j ACCEPT However I've locked down my outgoing connections and it means I can't resolve any DNS. How do I allow that? Also, any other feedback is appreciated. James

    Read the article

  • The script not working as expected files dump path

    - by user3319390
    I have a script needs to be dump matching cname from my file contains and then matching scode to dump file to $cname/$year/$month/$day/ into files like access and error logs #!/bin/sh #base_dir="/home/vizion/Desktop" path="/home/vizion/Desktop/adn_DF9D_20140515_0005.log" name=$(basename "$path" ".log") for x in *.log; do year=${x:9:4}; month=${x:13:2}; day=${x:15:2}; done while read -r line do cname=$(echo ${line} | awk '{split($7,c,"/"); print c[3]}') scode=$(echo ${line} | awk -F"[ ]" '{print $9}') [[ ! -d "$cname/$year/$month/$day" ]] && mkdir -p "$cname/$year/$month/$day/" [[ ( ${scode} -ge 200 ) && ( ${scode} -le 399 ) ]] && { # [[ ! -d "$cname/$year/$month/$day" ]] && mkdir -p "$cname/$year/$month/$day/" echo ${line} >> /home/vizion/Desktop/$cname/$year/$month/$day/${cname}_${name}_access.log } [[ ( ${scode} -ge 400 ) && ( ${scode} -le 599 ) ]] && { [[ ! -d "$cname/$year/$month/$day" ]] && mkdir -p "$cname/$year/$month/$day" echo ${line} >> ${cname}_${name}_error.log } done < $path i am able to filter logs but not not dumping the exact location It's going other locations suggest to me correction in script

    Read the article

  • Allow SFTP in iptables

    - by Kevin Orriss
    I have just purchased a VPS from linode and am going through the setup guide. I have everything running (apache2, php, mysql etc) but I am being denied access via SFTP when using fileZilla to upload a file. Now this is my second time installing the server as I missed a section out the first time. I was able to connect to my server through SFTP on filezilla the first time and the thing I missed out was adding a new user and editing the iptables in the firewall. So it would seem that the guide I have been following has blocked SFTP but allowed SSH. Here is the iptables file: *filter # Allow all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accept all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow all outbound traffic - you can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allow HTTP and HTTPS connections from anywhere (the normal ports for websites and SSL). -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allow SSH connections # # The -dport number should be the same port number you set in sshd_config # -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # Log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT All I would like is a line I need to put in there which allows SFTP over port 22. Thank you for reading this.

    Read the article

  • How to control/check CheckPoint rules changes (and another System events)

    - by user35115
    I need to check/control all system events on many CheckPoint FW1 - don't misunderstand - not rules triggering, but events such admins log on, rules changes and etc. I found out that I can make an log export using 2 methods: Grab logs Use special script that redirect Checkpoint log entries to syslog, FW1-Loggrabber But it's not clear for me does such logs also contain information that i need (admins log on, rules changes)? And If yes is it possible to filter events? I also suppose, that if system bases on *nix platform it must be a ploy - use based functions of the system to do what i want. Unfortunately i don't know where to "dig". May be you know? Updated: New info "FW-1 can pipe its logs to syslog via Unix's logger command, and there are third party log-reading utilities" So, the main question is how do my task in the best way? Has anybody already resolved such problem? P.S. I' m new with CheckPoint, so all information will be useful for me. Thank you.

    Read the article

  • Google Apps routing to different servers, depending on domain

    - by Philip
    We are investigating Google Apps for Education for our group of schools. Currently, each school uses their own Exchange (2003) server. Each school has its own domain which I have added to Google Apps as additional domains. I would like to start transitioning certain staff and some new pupils over to Google Apps to start testing. In this interim phase, I need mail to be routed through Google Apps and then, if no appropriate mail box is found, route on to the individual schools depending on the recipient. I do know that it is possible to route mail that does not have an appropriate Google Apps mail account to a single server - under "Settings / E-mail Settings / General Settings / Routing / E-mail routing". This works well for a single organisation where all the extra mail is destined for one place. I do know that it is possible to set up Routes, under "Settings / E-mail Settings / Hosts" and then use rules, found under "Settigns / E-mail Settings / General Settings / Routing / Receiving Routing". I can then filter based on e-mail domain and forward on to the necessary server. My problem with this, as I understand it, is that it ignores the users that have Google Apps accounts set up and sends all mail to the Exchange server. Are there any solutions for this predicament? Many thanks!

    Read the article

  • Locate devices within a building

    - by ams0
    The situation: Our company is spread between two floors in a building. Every employee has a laptop (macbook Air or MacbookPro) and an iPhone. We have static DHCP mappings and DNS resolution so every mobile gets a name like employeeiphone.example.com, every macbook air gets a employeelaptop.example.com and every macbook pro gets a employeelaptop.example.com on the Ethernet interface (the wifi gets a dynamic IP from a small range dedicated for the purpose). We know each and every MAC address of phones and laptops, since we do DHCP static mapping (ISC DHCP server runs on linux). At each floor we have a Netgear stack of two switches, connected via 10GB fiber to each other. No VLANs so far. At every floor there are 4 Airport Extreme making a single SSID network with WPA2 authentication. The request: Our CTO wants to know who is present at which floor. My solution (so far): Every switch contains an table listing MAC address and originating port. On each switch stack, all the MAC addresses coming from the other floor are listed as coming on port 48 (the fiber link). So I came up with: 1) Get the table from each switch via SNMP 2) Filter out the ones associated with port 48 3) Grep dhcpd.conf, removing all entries not *laptop and not *iphone 4) Match the two lists for each switch, output in JSON or XML 5) present the results on a dashboard for all to see I wrote it in bash with a lot of awk and sed, it kinda works but I always have for some reason stale entries in the switch lookup tables, making it unreliable; some people may have put their laptop to sleep, their iphones drop connections after a while, if not woken up and so on..I searched left and right, we are prepared to spend a little on the project too (RFIDs?), does anybody do something similar? I can provide with the script if needed (although it's really specific to our switches and naming scheme). Thanks! p.s. perhaps is this a question for stackoverflow? please move if it so.

    Read the article

  • Identifying test machines in analytics logs

    - by RTigger
    We're just beginning to add analytics to our SaaS application, to begin (among other things) billing clients based on usage. The problem we're running into is there's a few circumstances where our support team will simulate a log in into production to try to reproduce reported issues with a client's configuration. When they log in, an entry will be made into our analytics logs that their specific account has logged in, which we use to calculate billing. A few ideas we had to solve this: 1) We log IP addresses as well as machine keys for each PC that logs in - we could filter out known IP addresses and/or machine keys belonging to support. The drawback is we have to maintain a list of keys / addresses manually. 2) If support (or anyone else internal) runs our application in debug mode (as opposed to release), it will not report analytics. This is fine, as long as support / anyone else remembers to switch to debug mode. 3) Include some sort of reg key / similar setting required to be set when configuring a production system in order to send analytics. Again, fine, as long as our infrastructure team remembers to set the reg key or setting. All of these approaches require some sort of human involvement, which we all know can be iffy at best. Has anyone run into a similar situation? Is there an automated approach to this problem? (PS Of course, we shouldn't be testing in production, but there are a few one-off instances with customer set up that we can't reproduce without logging in as them in production. This is the only time we do so, and this is the case I'm talking about in this question.)

    Read the article

  • Shell script to block proftp failled attempt

    - by Saif
    Hello, I want to filter and block failed attempt to access my proftp server. Here is an example line from the /var/log/secure file: Jan 2 18:38:25 server1 proftpd[17847]: spy1.XYZ.com (93.218.93.95[93.218.93.95]) - Maximum login attempts (3) exceeded There are several lines like this. I would like to block any attempts like this from any IP twice. Here's a script I'm trying to run to block those IPs. tail -1000 /var/log/secure | awk '/proftpd/ && /Maximum login/ { if (/attempts/) try[$7]++; else try[$11]++; } END { for (h in try) if (try[h] > 4) print h; }' | while read ip do /sbin/iptables -L -n | grep $ip > /dev/null if [ $? -eq 0 ] ; then # echo "already denied ip: [$ip]" ; true else logger -p authpriv.notice "*** Blocking ProFTPD attempt from: $ip" /sbin/iptables -I INPUT -s $ip -j DROP fi done how can I select the IP with "awk". with the current script it's selecting "(93.218.93.95[93.218.93.95])" this line completely. But i only want to select the IP.

    Read the article

  • Iptables - forward email ports?

    - by Emmet Brown
    im trying to open some local ports (LAN) and then re-direct them to another server (WAN) using iptables. Here is my config: #WAN allow-hotplug eth1 auto eth1 iface eth1 inet static #Tarjeta red WAN address 192.168.2.2 gateway 192.168.2.1 netmask 255.255.255.0 #LAN allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.16.6 netmask 255.255.255.0 network 192.168.16.0 broadcast 192.168.16.255 I try this: iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 110 -j DNAT --to 200.40.30.218:110 iptables -A FORWARD -p tcp -i eth0 -o eth1 -d 200.40.30.218 --dport 110 -j ACCEPT iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 25 -j DNAT --to 200.40.30.218:25 iptables -A FORWARD -p tcp -i eth0 -o ethq -d 200.40.30.218 --dport 25 -j ACCEPT but, it did not work. i also try changeing eth0 to eth1 (and eth1 to eth0) but nothing happened. Starting Nmap 5.00 ( http://nmap.org ) at 2011-10-03 14:44 UYST Interesting ports on 192.168.16.6: Not shown: 997 closed ports PORT STATE SERVICE 22/tcp open ssh 111/tcp open rpcbind 8080/tcp open http-proxy Im running debian. Can u guys help me to check what is happening? edit: IPTABLES-SAVE # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *mangle :PREROUTING ACCEPT [139993:77867651] :INPUT ACCEPT [139385:77761761] :FORWARD ACCEPT [186:12071] :OUTPUT ACCEPT [173556:74341650] :POSTROUTING ACCEPT [173734:74352988] COMMIT # Completed on Mon Oct 3 15:43:14 2011 # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *nat :PREROUTING ACCEPT [1649:190626] :POSTROUTING ACCEPT [6729:339646] :OUTPUT ACCEPT [6697:337660] -A PREROUTING -i eth0 -p tcp -m tcp --dport 110 -j DNAT --to-destination 200.40.30.218:110 -A PREROUTING -i eth0 -p tcp -m tcp --dport 25 -j DNAT --to-destination 200.40.30.218:25 COMMIT # Completed on Mon Oct 3 15:43:14 2011 # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *filter :INPUT ACCEPT [138307:77066136] :FORWARD ACCEPT [168:11207] :OUTPUT ACCEPT [172288:73655708] -A FORWARD -d 200.40.30.218/32 -i eth0 -o eth1 -p tcp -m tcp --dport 110 -j ACCEPT -A FORWARD -d 200.40.30.218/32 -i eth0 -o ethq -p tcp -m tcp --dport 25 -j ACCEPT COMMIT # Completed on Mon Oct 3 15:43:14 2011 Regards

    Read the article

  • With Ubuntu 12.04 unlike 11.04 Wine installed application start menu links are missing

    - by Ron Whites
    With Ubuntu 12.04 and wine 1.4 unlike ubuntu 11.04 with wine 1.2.2 installed application start menu links are missing. For instance with Ubuntu 11.04 including Wine I can install one of our Windows applications and then can go to Applications Wine Programs Semantic Designs TestCoverage Documentation to bring up the documentation for how to run our tool. Unfortunately with Ubuntu 12.04 the Applications menu is gone and going to Dash I do see "Recent Apps and more apps" but my installed Wine application and related documentation link is shown present, even though the wine uninstaller shows in present. I found this online suggestion and tried using the gnome "main menu"... Windows key to launch the Dash. Enter "Main Menu" in the search field and open the old Edit Main Menu app. Select the Category (aka Unity Dash Filter) you want the item in. Name the Dash/Launcher Item Add the Command to launch said app With "mainmenu" then get down to the TestCoverage Documentation and I could see a command link in properties of .. env WINEPREFIX="/home/sdtest/.wine" wine C:\windows\command\start.exe /Unix /home/sdtest/.wine/dosdevices/c:/users/sdtest/Start\ Menu/Programs/Semantic\ Designs/Test\ Coverage/Java\ 1.7\ Documentation.lnk BUT I could not execute this link to view the installed documentation. So I copied the link properties into a file, set it as executable, and ran it as a bash script and the documentation came up! So why can't I use this link under main menu?

    Read the article

  • Configuring iptables rules for HAProxy and others

    - by MLister
    I have the following relevant settings for HAProxy: defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 500 contimeout 5s clitimeout 15s srvtimeout 15s frontend public bind *:80 option http-server-close option http-pretend-keepalive option forwardfor # ACLs ... I have three backends (including a Nginx server) configured in HAProxy, all listening on different ports of 127.0.0.1. And my iptables config is this: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT My questions are: Would the above iptables config work with the settings/options in my HAProxy config? I am also runnning a postgres and a redis server on the same machine, what settings do I need to adjust for these two to enable them work with iptables?

    Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >