Search Results

Search found 17336 results on 694 pages for 'richard long'.

Page 169/694 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

  • Wireless router blocking some sites while using ethernet is fine

    - by Micke
    I'm using Windows 7 and my router is a wireless Apple Airport Express that is approximately two years old. Suddenly I can't access some sites (for example www.sthlm.friskissvettis.se, or www.vegetarian-shoes.co.uk, some streamed tv-shows on svtplay.se, and a number of other random sites) when connecting to internet with my router. It worked good until recently and I'm fairly sure this problem emerged when my ISP upgraded from 10/10mbit to 100/10mbit speed. Most other sites like facebook and google works fine. When using my network cable to connect to internet everything works fine and I can access these sites. Firmware is current and I've tried reseting the router to factory defaults. Tried different browsers, and I can't ping the "blocked" sites either. Tracert www.sthlm.friskissvettis.se starts with 10.0.0.1 and continues through a number of long addresses until it says timeout. The last working address before timeout was sth-tcy-ipcore01-ge-0-2-0.neq.dgcsystems.net [83.241.252.13], if it matters. Tracert www.vegetarian-shoes.co.uk also eventually gives me a timeout. When the network cable is plugged in, I still get timeout on tracert www.sthlm.friskissvettis.se even though I can access the site in Chrome. Weird. www.vegetarian-shoes.co.uk doesn't give me a tracert timeout when the cable is plugged in, and I can access the site as usual. I've tried changing DNS servers to use opendns servers instead, but to no use. I've tried pinging these two sites with a lower MTU packet size (with this method: http://www.richard-slater.co.uk/archives/2009/10/23/change-your-mtu-under-vista-or-windows-7/), but still can't access them through ping... I don't know what to do anymore.... any suggestions???

    Read the article

  • "Learning" Linux

    - by Strider
    I've been interested in computers for a long time and have fiddled with a lot of stuff which includes Linux. I started out with Red Hat when I was young (around 13) and lost all data, converting a FAT32 drive to something else. Later it was Knoppix which was really helpful in recovery and such. Then, it was Ubuntu. Also, I fiddled with Arch for some time, but, it breaks too often for my liking (maybe, I should have been more careful). Anyway, currently I use Ubuntu 9.04. I want to dig deeper into the Linux world now. I want to learn how things work and use the terminal more. I am a programmer as well, so, it will help a lot. So, the thing I wanted to ask were: Good books to learn and understand Linux Good habits to use Linux more efficiently. Good tools about which I should know. Amount of time you set aside to learn about new things each day. As a programmer, how do you setup and use Linux efficiently. Long list. I will be grateful to the answerers.

    Read the article

  • Need troubleshooting advice for intermittent dns problems with requests on isp nameservers

    - by Mnebuerquo
    I've been having some intermittent dns problems with a web server, where certain isp's dns servers don't have my hostnames in cache and fail to look them up. At the same time, queries to opendns for those hostnames resolve correctly. It's intermittent, and it always works fine for me, so it's hard to identify the problem when someone reports connectivity problems to my site. My website is on a server running linux with Plesk. My dns records are configured with plesk (so my server is its own dns master). Domain name is registered with godaddy. I'm not real knowledgeable about dns, so I don't really know how to begin with troubleshooting. I've started learning to use dig, but while I can read the manpage to learn the syntax, I don't really know what questions to ask. Since the problem is intermittent I haven't been able to really catalog many symptoms. Symptoms I have observed: Certain people repeatedly reported intermittent problems connecting to my website. This was only from certain networks. (Ex: One guy could connect reliably from his office but not his home.) Sometimes I notice my browser taking a long time looking up the hostname for my site (Firefox shows a message in the status bar at the bottom). For me this is in the ten second range. ssh connections from anywhere to my server take a long time to connect but then seem to work fine once connected. So hopefully the folks on serverfault can point me to a good beginner tutorial for understanding dns, and suggest troubleshooting questions to ask next time one of my users reports connectivity problems.

    Read the article

  • bind9 dlz/mysql at ubuntu segfault libmysqlclient.so

    - by Theos
    I have a big problem. I installed the bind9 nameserver to three different computer. two Ubuntu 10.04.4 LTS, and one Ubuntu 11.10 I compiled it 9.7.0, 9.7.3, 9.9.0 with this method: ./configure --prefix=/usr --sysconfdir=/etc/bind --localstatedir=/var \ --mandir=/usr/share/man --infodir=/usr/share/info \ --enable-threads --enable-largefile --with-libtool --enable-shared --enable-static \ --with-openssl=/usr --with-gssapi=/usr --with-gnu-ld \ --with-dlz-mysql=yes --with-dlz-bdb=no \ --with-dlz-filesystem=yes --with-geoip=/usr make make install After the set up for dlz/mysql, the BIND server is working perfetctly until 5-30 minute long. Ahter i got segfault. I resolve temporaly the problem with a simple process watchdog, and if the named is stopped, the watchdog is restart it, but this is not a good idea in long therm. My log output is: messages: Apr 13 19:33:51 dnsvm kernel: [ 8.088696] eth0: link up Apr 13 19:33:58 WATCHDOG: named not running. Restarting Apr 13 19:35:08 dnsvm kernel: [ 87.082572] named[1027]: segfault at 88 ip b71c4291 sp b5adfe30 error 4 in libmysqlclient.so.16.0.0[b714e000+1aa000] Apr 13 19:35:08 WATCHDOG: named not running. Restarting Apr 13 19:35:08 dnsvm kernel: [ 87.457510] named[1423]: segfault at 68 ip b71d6122 sp b52f0a40 error 4 in libmysqlclient.so.16.0.0[b7160000+1aa000] Apr 13 19:35:09 WATCHDOG: named not running. Restarting Apr 13 19:41:56 dnsvm kernel: [ 494.838206] named[1448]: segfault at 88 ip b731c291 sp b5436e30 error 4 in libmysqlclient.so.16.0.0[b72a6000+1aa000] Apr 13 19:41:57 WATCHDOG: named not running. Restarting Apr 13 19:57:26 dnsvm kernel: [ 1424.023409] named[2976]: segfault at 88 ip b72d1291 sp b6beee30 error 4 in libmysqlclient.so.16.0.0[b725b000+1aa000] Apr 13 19:57:26 WATCHDOG: named not running. Restarting Apr 13 20:11:56 dnsvm kernel: [ 2294.324663] named[6441]: segfault at 88 ip b7357291 sp b6473e30 error 4 in libmysqlclient.so.16.0.0[b72e1000+1aa000] Apr 13 20:11:57 WATCHDOG: named not running. Restarting syslog: http://pastebin.com/hjUyt8gN the first server is a native, normal x64 server (u1004lts), the second is virtualised server (u11.10) the third is also virtualised (10.04lts) This servers is only for dns providing with mysql server db. But the problem is be with all server, and all bind version. named.conf: http://pastebin.com/zwm1yP7V Can anybody help me, or any good idea?

    Read the article

  • Is this memory compatible with this motherboard???

    - by ClarkeyBoy
    Hi, I have a Foxconn P35AP-S as seen here. I need to get some more RAM since I only have 1 2GB stick. The current one is 1066MHz. I would like to get the memory situated here: www.scan.co.uk/Products/6GB-(3x2GB)-Corsair-XMS3-Classic-DDR3-PC3-10666-(1333)-Non-ECC-Unbuffered-CAS-7-7-7-20-165V memory. It is 6GB of Corair 1333MHz memory. According to the motherboard website it is able to take 1333MHz, but it says oc** next to it (which means achieved when overclocked). So my question is: are they still compatible without overclocking, or does the motherboard require overclocking to be compatible? If it requires overclocking (which I have no idea how to do) can anyone recommend any other memory (in the region of 6GB) which the motherboard is compatible with? I'd rather it were from Scan, but to be honest it doesnt need to be. Many thanks in advance. Regards, Richard Edit: I just realised that the motherboard has a maximum capacity of 4GB of RAM. Scrap the RAM given above, I'd like to go for something like that but only 4GB. Edit: Scrap that last edit - its only if I go for DDR3 that I need to take this into account. DDR2 is a maximum of 8GB.

    Read the article

  • Need to get SMTP server on MS Server 2003

    - by Matt Dawdy
    Long story short, client paid networking company to move their website in house. Now I have to figure out how to email out from their website even though they don't have an SMTP server. At least until I install one. Their email is hosted with Gmail right now (the client's domain through Google App for Your Domain). I changed my code to connect as one of their users "[email protected]" and send email. Worked great for about 12 hours. All of a sudden none of the automated emails are going out now, and google is sending the emails back saying that it is a permanent failure and Message Rejected. The link they direct me to, http://mail.google.com/support/bin/answer.py?answer=69585 is telling me that our emails look like spam. They aren't. They are emails we send to out clients about the status of their applications. Seriously, they are NOT spam. So...long story short is out the window, sorry...but I need to get an SMTP server setup inside their domain that I can send emails out of. This thing won't need to receive emails ever, and really only needs 1 email account customercare. What can I do? Will I have to have the networking company open a port in the firewall? Is there one built into Server 2003?

    Read the article

  • Maxtor 500GB external hard drive not being detected but power is going to it?

    - by ClarkeyBoy
    I have 2 * Maxtor Onetouch 4 Lite 500GB external hard drives (part no. 9NT2A4-500). They both used to work fine on my old laptop (an Acer) but I have not used them for about a year, since my laptop was stolen and I got this one (also an Acer [Aspire 7738G]). I have one plugged into the mains with one of the leads I believe was supplied with them. It appears to be receiving power as it is warm and the power light (on the unit itself) is on; also the mains adapter is fairly warm. I also have it plugged into my laptop with a USB lead which I have tested on my mp3 player (so I know it works). However my hard drive is not showing on my computer. I have tried checking for new hardware, installing the software that was supplied with it, checking drive letters in case it is registered as C: or something stupid, checking for problems etc... I can't find any cause for it to do this. It does appear to be starting up and, possibly, shutting down and restarting constantly (that's what it sounds like altho I can't be certain). I have had both hard drives stored in different places for the last year and they're both doing the same thing.. if it was only one then I'd guess it had got damaged or corrupted or something but since it is both I doubt this is it. The only things in common with both of them are the leads and the laptop, however I know the USB lead works and guess the mains lead works as there is power going to the unit. Has anyone come across this before or does anyone have any idea what the cause / solution to the problem is? Any help would be greatly appreciated. Regards, Richard

    Read the article

  • Why does just splitting an Ethernet cable not work?

    - by Sin Jeong-hun
    I thought the Ethernet is logically a one-line communication bus (for argument's sake, I am excluding hubs). All machines attached on the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why would splitting one Ethernet line from my home router into two and connecting two computers not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room, and I had put a computer in another room (also my room, though). Since a wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

    Read the article

  • Websites down EC2 inaccessible via SSH CPU utilisation 100% last few hours - what should I do?

    - by fuzzybee
    I have multiple websites hosted on 1 single EC2 instance. 1 website "abc" were down for a few hours, sometimes threw database connection error and sometimes just took too long to respond. 1 website "def" were incredibly slow but still up and running the rest of the websites had the same symptoms has "abc" I can afford 15 min or less down time for "def". Should I then (in AWS console) reboot my instance or create an AMI image from my instance and launch it and associate my elastic IP to the new instance or "launch more like this" Background on what may have happened to my ec2 The last time I made changes for 21 hours ago. A cronjob to create snapshots ran around 19 hours ago and it has been running for a long time. Google Analytics shows traffic to my websites such as kidlander.sg has been nothing exceptional. Is there any other actions I should take or better options I could have? (I have already contacted AWS support but their turnaround is 12 hours so I appreciate all the help I could get) Update I got everything back up and running and CPU utilisation back to normal, around 30%. There is 1 difference between "def" and "abc" as well as my other websites "def"'s database is hosted on RDS "abc"'s database is hosted on an EC2 instance (different from my web server instance) configured by myself Nevertheless, I checked the EC2 instance I'm using as MySQL server yesterday and it was absolutely fine during the incident low CPU ultilisation I could log in using linux command line

    Read the article

  • Apache no longer starts at Windows boot up

    - by w3d
    I have Apache installed as part of XAMPP - local test server. It is configured as a Windows (XP) Service. Startup type is "Automatic". For a long time now it has always started when Windows boots up, but recently this has stopped happening. I now need to start it manually via the XAMPP Control Panel - at which point it appears to start up perfectly OK. The only recent updates to the machine (that I recall) are Windows Updates - none of which appear to have "known issues" that relate to this. And updates to Google Chrome. Any ideas what could prevent Apache from starting automatically at Windows (XP) boot up? EDIT#1 There are 2 related Errors in my system event log regarding the Service Control Manager: Timeout (30000 milliseconds) waiting for the Apache2.2 service to connect. The Apache2.2 service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. When I manually start the Apache server after boot up there are 2 "information" events stating that it was "sent a start control" and that it "entered the running state". Although I notice it appears to take 19 seconds between the start control being sent and entering a running state - according to the event log. So, maybe 30 seconds during boot up isn't long enough (anymore) for Apache to start??

    Read the article

  • Windows 7 Not Starting and System Repair Not Loading

    - by Mark
    I have a Dell Inspiron 1545 running Windows 7 When turning on my PC I keep receiving a black screen with the option to use System Repair or Start Normally. Both options lead me to the System Repair background except no matter how long I wait the system restore options never show up. Choosing F8 and running all of the options including safe mode encounters the same result above. I tried to to use 2 system recovery disks 32x and 64x I downloaded and both lead to similiar results. When I choose System Repair running from the disk the System Repair Question asking to select a language pops ups but after this no matter how long I wait no other options appear. Next after restarting and selecting F8 (after hitting f12 and running from CD) I choose 'Run From Safe Mode with Command Prompt' I am able to run all of the options from System Restore with differing results: Startup Repair: Choosing this ends up in system repair indefinitely (left running 12 hrs) System Restore: Does Nothing. PC thinks for a second and then stops. When selecting ShutDown I see an error message stating there are no restore points. System Image Recovery: Service Cannot be started in Safe Mode Windows Memory Diagnostic: Runs test but then leads to system repair background which never loads system repair Command Prompt: chkdsk /r -Cannot Lock Current Drive...write protected. chkdsk /f -Cannot Lock Current Drive...write protected. bootcfg - Cannot open Boot.Ini file bootcfg - Ran all 3 (rebuildBcd, FixMbr and Fixboot) but PC still goes to System Repair background with no repair options popping up upon restart (without recovery CD). I'm on the verge of purchasing a boot utility disk for $50 unless there is anything else short of "take it to a computer shop" that somebody can suggest I try.

    Read the article

  • Why do most songs in my media collection play twice? - Corrupt media?

    - by Dean
    Problem: Whether I'm playing the media with Rhythmbox on Ubuntu, Winamp on Windows, or my Nokia N95's media player, most of my audio files (OK, maybe only 40%) play twice. Info: I have a 500GB external 2.5" WD HDD, with a 150GB primary FAT32 partition labeled MUSIC. Inside this, I have about 500 folders containing about 10,000 MP3/WMA/M4A/WAV files. I manage the drive using Ubuntu 9.10, and frequently copy data to/from it using RSYNC, or on windows, TotalCopy. The visual output is different in each media player, but it behaves as if the 1 MP3 has the same song on it twice, and as soon as it ends it begins again. Winamp shows that the song goes for 2x as long as it should, The N95's media player shows the progress bar off the right-hand-side of the screen when it begins playing (then jumps back to the left, then continues along...). Rhythmbox doesn't show me how long the song is, nor does the progress bar move along the screen. Plea: It seams to me somewhere along the lines my collection has become corrupt... but where? And how? and please someone tell me I can fix it!! TIA, Dean.

    Read the article

  • Is there any way to send Outlook meeting requests from a non-default calendar?

    - by rbeier
    Hi, We have a user with two Outlook accounts. [email protected] is of type Exchange; [email protected] is of type IMAP/SMTP. Both are actually on our Exchange server; but since an Outlook profile can only have one Exchange account, the second one is set up as IMAP. The user would like to send a meeting request from her xyz.com account, so the "from" address appears as [email protected]. Unfortunately that doesn't work. If she creates the meeting in her xyz.com calendar, the meeting request still goes out through her Exchange account, [email protected]. The meeting request "compose message" window has an Account dropdown below the Send button, but this has no effect. Before she sends the invitation, a warning appears: "Responses to this meeting request will not be tallied because this meeting is not in your main Calendar folder. Is this OK?" Is there any workaround for this? We're using Outlook 2007 and Exchange 2003 SP2. Thanks, Richard

    Read the article

  • Value of Itanium over x86_64 for Oracle Deployment

    - by Antitribu
    We are looking at a new environment to run our Oracle Database running on SUSE (potentially migrating to RedHat). Our database is approximately 100GB and performs adequately on our current hardware (x86_64) with approximately 6GB of ram allocated to it. We are growing quickly however and will require more performance shortly. Given the cost of Oracle licenses we would like to maximize the value from each license by choosing the most appropriate CPU to run the software on. The questions are: Are there substantial benefits to looking at Itanium hardware, are there any drawbacks? Is there a point where Itanium starts to scale out better? What are the long term support options for Itanium? Given the dominance of x86 would it be safer long term to stick with x86? On average what would be the performance benefit of implementing an Oracle database on Itanium over x86_64? Is this an issue at all or will other factors (IO/RAM) cap out first? If anyone can point me towards some solid documentation on comparisons between the two platforms that provides good case analysis of when to choose which I'm more than happy to accept that as an answer.

    Read the article

  • Overheating Toshiba Satellite L300

    - by ldigas
    A coleague of mine's having trouble with his new Toshiba Satellite L300 ... I tool a kook at it, and indeed it's hot as hell. I couldn't hold my hand on it for too long. He says it also has a tendency to turn itself off (WinXP 32bit running) with no forewarning. Hasn't happened to me while I was using it, but that wasn't long anyways. The first guess was it was too dirty ... problem is it's new, came out of a package a quarter of a year ago. Kept in a clean environment (office). Looks clean. No dust in sight. Second guess is that the fan wasn't working properly, cause indeed it has intervals of working, and non working. But when I listen to it, it sounds like normal usage. I took a SpeedFan measurement, and it reports temp. up to 85 Celsius ... which is definitely too high. Anyone knows what else I could do to it ? It is under warranty and it will go to the service, but I thought if there is something we can do, as to avoid carrying it there / be without it for a week ...

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • prevalent, recurring hardrive failure intel macbook from 2006/2007

    - by SimonSalman
    Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

    Read the article

  • Painfully slow login to AD bound Mac OS X Leopard machine when off home network

    - by GeeBee
    Dear all Just looking for a little help with this problem that seems to trip a lot of people up and is causing me no end of grief. I have a number of fully patched OS X Leopard machines that are bound to my AD (Server 2003). When on the home network, logging in seems swift and works as expected. When users take the machines off site, login can take 5 minutes or more. The user adds correct credentials but the desktop does not appear for a very long time. Outside the office, I have tried logging in using a local Admin account, switching off Airport and then logging in using an AD account. In this situation login is immediate again. It all seems as if Leopard is finding a suitable wireless network, spending far too long looking for the Domain before eventually giving up and using the cached credentials instead. I have read that disabling Bonjour on the machine will stop this problem (i have not yet tested) http://www.macwindows.com/leopardAD.html#111607z ...but I am reluctant to use this "Solution" as I would like to be able to use Bonjour on the local network as well as having AD-bound machines. However, is disabling Bonjour really the only answer? Is there not some time-out setting somewhere that could be amended to stop Leopard spending forever looking for home? Any help would be very gratefully received Thanks Gordon

    Read the article

  • Macbook Pro - 15" with i7 processor - Any problems with heat?

    - by webworm
    You may have already heard about the review done by the folks at PC Authority in Australia, where they had an i7 MacBook Pro that got up to 100 degrees Celsius during benchmarking. Here is the URL in case you have not read it. http://www.pcauthority.com.au/News/172791,macbook-pro-helps-core-i7-hit-100-degrees.aspx In any case, I was considering purchasing a 15" Macbook Pro with the i7 processor and the NVIDIA GeForce GT330M with 512 video memory. Having read how hot the computer got I started to become hesitant about purchasing. My main concern is long term damage to the computer due to excessive heat. I plan to use the MacBook Pro as a development machine where I will be running Windows 7 within VMWare Fusion or Virtual Box. Within the VM I will be running IIS, SQL Server, Visual Studio and SharePoint Server. Hence why I would like to have the power of the i7 processor. That is why I wanted to check with actually owners of the MacBooks with the i7 processor and see what their experiences have been. Have you noticed excessive heat? How does your Macbook handle process intensive apps over long periods of time? Thank you!

    Read the article

  • How do hdparm's -S and -B options interact?

    - by user697683
    These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

    Read the article

  • How to set CA cert file for LDAP backend server in smbpasswd configuration

    - by hayalci
    I am having a problem with smbpasswd, an LDAP backend server and SSL/TLS certificates. The client machine that I run smbpasswd on is a Debian Etch machine, and the Ldap server is Sun DS running on Solaris. All the following occurs on the client. When I disable SSL, by setting "ldap ssl = no" in smb.conf, the smbpasswd program works without errors. When I set "ldap ssl = start tls", the following messages are printed by smbpasswd and there is a long timeout period before any password is asked by it Failed to issue the StartTLS instruction: Connect error Connection to LDAP server failed for the 1 try! ..... long delay ..... New SMB password: Retype new SMB password: Failed to issue the StartTLS instruction: Connect error Connection to LDAP server failed for the 1 try! smbpasswd: /tmp/buildd/openldap2-2.1.30/libraries/liblber/io.c:702: ber_get_next: Assertion `0' failed. Aborted I conducted some tests with "ldapsearch -ZZ". It was not working at first, but after I added the TLS_CACERT line to /etc/ldap/ldap.conf, /etc/libnss-ldap.conf and /etc/pam_ldap.conf, it started working. So relevant TLS sections in all those files are: ssl start_tls tls_checkpeer no tls_cacertfile /path/to/ca-root.pem TLS_CACERT /path/to/ca-root.pem But the smbpasswd program continued giving the error. I tried creating /etc/smbldap-tools/smbldap.conf file with following content (after consulting debian docs for smbldap-tools package) But as I see, smbpasswd comes with samba-common package and does not use the configuration for smbldap-tools utilities. verify="optional" cafile="/path/to/ca-root.pem" My question is: How can I set which SSL CA Certificate is used by smbpasswd program ?

    Read the article

  • Looking for an application to record audio and video on a linux "embedded" device

    - by Luke404
    I am working with a linux x86 device with limited CPU resources (as a prototype we just use a pentium-m netbook). We'd like to record video from one V4L2 device (we'll probably end up using just USB Video Class devices like all modern webcams) and one audio stream from an ALSA source. The thing will not have screen and keyboard, and obviously no X11 environment. Goals are: do as little work as possible to cope with little cpu resources - for example I'd like to record video in the native MJPEG I get out of the UVC devices encoding audio to MPEG3 Layer-2 (aka mp2) is ok since it let us save a lot of space (compared to raw pcm samples) and does use little cpu power I don't mind loosing some video frames here and there (UVC devices do that) as long as I can get audio and video streams syncronized not require user input to start the thing (a python script takes care of initialization, startup, shutdown, etc...) be able to open the resulting files for postprocessing without too much effort (ie, if mplayer or vlc can play it, it's fine) So far the only app I found that could be started from command line and record V4L2 video + ALSA audio is mencoder but I'm having some difficulties with it. It should be able to do that but I cannot record audio and video together - just one of the two. And if I use two different processes to record to two different files I have no means to get them in sync (audio is more or less always correct, but video framerate will vary over time and it seems to lack timestamps to correctly play it back to the correct time). Long story short, how do you record an unconverted MJPEG stream (from an UVC device) and an audio stream (from an ALSA device, possibly encoding to any standard format) using a command line tool, to a single file (MPEG or any other container), keeping audio and video in sync?

    Read the article

  • How can I recover a Fedora 12 installation that is showing signs of disk errors?

    - by Bob Cross
    I am currently overseas (i.e., very far from my normal library of tools) and my primary machine that would normally act as the data server in the performance test that we're trying to run is failing to boot to Fedora 12 properly. This is a machine that, as of yesterday, was booting fine. However, this morning, very strange portions of the boot process were complaining with messages such as "unexpected 0x0 in rpcbind" and "bad file descriptor" (I don't have the error in front of me - scavenged a windows installation to get onto serverfault). Eventually, the boot hung for a long time at the NFS service and then brought up what looked like the KDE login screen but neither the mouse nor keyboard functioned. In olden days, I would try to get to a point where I could manage to run fsck and pray that the bad sectors would come back into alignment just long enough for me to scrape the critical data off of the machine. However, now that we live in the future, it seems like our options in situations like this should be a little more varied. Is there a way to recover a Fedora 12 installation with bad disk sectors that won't boot properly? For completeness, I am comfortable working with bootable recovery distros-on-CD and such but I don't know which one is likely to work best with modern Fedora. In the absence of guidance, I'm frantically torrenting the Fedora 12 Live CD and DVD, hoping to try rescue mode before tomorrow morning.

    Read the article

  • What to look for in a reliable backup hard disk?

    - by Senthil
    I want to buy an internal hard disk and use a docking station along with it for backing up important data. The size will be around 500GB to 1TB. I have a budget and several models fit into it. So far, they only seem to vary in size, speed and brand. These are the only things I can compare from the specs. I guess asking for which brand is best is completely subjective so I won't do that. I want my disk to have long life and be reliable. Doesn't matter if it is somewhat slow. Size: Should I go for the one with highest size within my budget? Will higher density cause problems? Or should I go for a moderately sized one? Does the number of platters have an impact? Speed: I do not want high performance. I want it to be reliable and last long. I am definitely not going to choose the expensive 10,000 rpm ones. Should I go for 5400 or 7200? Do these numbers affect longevity and reliability? Are there any other technical and objective factors that I should look for?

    Read the article

  • Can't log in using second domain controller when first DC is unreachable

    - by rbeier
    Hi, We're a small web development company. Our domain has two DCs: a main one (BEEHIVE, 192.168.3.20) in the datacenter and a second one (SPHERE2, 10.0.66.19) in the office. The office is connected to the datacenter via a VPN. We recently had a brief network outage in the office. During this outage, we weren't able to access the domain from our office machines. I had hoped that they would fail over to the DC in the office, but that didn't happen. So I'm trying to figure out why. I'm not an expert on Active Directory so maybe I'm missing something obvious. Both domain controllers are running a DNS server. Each office workstation is configured to use the datacenter DC as its primary DNS server, and the office DC as its secondary: DNS Servers . . . . . . . . . . . : 192.168.3.20 10.0.66.19 Both DNS servers are working, and both domain controllers are working (at least, I can connect to them both using AD Users + Computers). Here are the SRV records that point to the domain controllers (I've changed the domain name but I've left the rest alone): C:\nslookup Default Server: beehive.ourcorp.com Address: 192.168.3.20 set type=srv _ldap._tcp.ourcorp.com Server: beehive.ourcorp.com Address: 192.168.3.20 _ldap._tcp.ourcorp.com SRV service location: priority = 0 weight = 100 port = 389 svr hostname = beehive.ourcorp.com _ldap._tcp.ourcorp.com SRV service location: priority = 0 weight = 100 port = 389 svr hostname = sphere2.ourcorp.com beehive.ourcorp.com internet address = 192.168.3.20 sphere2.ourcorp.com internet address = 10.0.66.19 Does anyone have any ideas? Thanks, Richard

    Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >