Search Results

Search found 1193 results on 48 pages for 'cisco pix'.

Page 17/48 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Can IOS be upgraded on a Cisco Catalyst 6509 switch without downtime?

  - by Massimo

  There's this Cisco Catalyst 6509 switch with 2 (two) supervisor modules; one of them is active, the other is (almost always) in standby. We need to upgrade IOS; current version is 12.2.something (I can check exactly which one, if this does matter). Can this be done without service interruption? Something like "upgrade the standby supervisor, activate it, upgrade the other one"?

  Read the article

• How to auto dial 9+Number on Cisco 7941 redial?

  - by NotDan

  Is it possible to set up a Cisco 7941 phone to dial 9 before the redial number? When I view missed calls, and try to redial one of the numbers, it always fails because it doesn't dial 9 first. I have to write the number down and then manually dial the 9 and then the number.

  Read the article

• Is there Muticast routing support on a Cisco 3750?

  - by mrtechalot

  We have a switch (Cisco WS-C3750G-48TS) with only a C3750-IPBASE-M image (not a 'C3750-IPSERVICES-M' license). Is there any kind of multicast support here? All I need it to do is route multicast packets to an RP (ip pim sparse-mode). Do we really need the service (C3750-IPSERVICES-M) license/image?. The uplink switch is running C3750-IPSERVICES-M, but this switch doesn't seem to carry any ability to configure multicast on an interface.

  Read the article

• What is the purpose of the QAbstractButton::checkStateSet() method?

  - by darkadept

  I'm writing my own 4 state button and I'm not quite sure what to put in the checkStateSet() method, if anything. Here is what I've got so far: SyncDirectionButton::SyncDirectionButton(QWidget *parent) : QAbstractButton(parent) { setCheckable(true); setToolTip(tr("Click to change the sync direction")); _state = NoSync; } void SyncDirectionButton::paintEvent(QPaintEvent *e) { static QPixmapCache::Key noneKey; static QPixmapCache::Key bothKey; static QPixmapCache::Key leftKey; static QPixmapCache::Key rightKey; QPainter p(this); QPixmap pix; if (checkState() == SyncLeft) { if (!QPixmapCache::find(leftKey, &pix)) { pix.load(":/icons/sync-left.png"); leftKey = QPixmapCache::insert(pix); } } else if (checkState() == SyncBoth) { if (!QPixmapCache::find(rightKey, &pix)) { pix.load(":/icons/sync-right.png"); rightKey = QPixmapCache::insert(pix); } } else if (checkState() == SyncRight) { if (!QPixmapCache::find(bothKey, &pix)) { pix.load(":/icons/sync-both.png"); bothKey = QPixmapCache::insert(pix); } } else if (checkState() == NoSync) { if (!QPixmapCache::find(noneKey, &pix)) { pix.load(":/icons/application-exit.png"); noneKey = QPixmapCache::insert(pix); } } p.drawPixmap(0,0,pix); } SyncDirectionButton::DirectionState SyncDirectionButton::checkState() const { return _state; } void SyncDirectionButton::setCheckState(DirectionState state) { setChecked(state != NoSync); if (state != _state) { _state = state; } } QSize SyncDirectionButton::sizeHint() const { return QSize(180,90); } void SyncDirectionButton::checkStateSet() { } void SyncDirectionButton::nextCheckState() { setCheckState((DirectionState)((checkState()+1)%4)); }

  Read the article

• Any problems usinga GoDaddy SSL certificate on a Cisco ASA firewall?

  - by Richard West

  I need to purchase and install a SSL certificate on my Cisco ASA firewall. This will allow my VPN users to connect to my ASA without receiving the certificate error from the untrusted self assigned SSL certificate that is currently on the ASA. I had good experiences with the SSL certificates that GoDaddy sells. However, I'm concerned about using them. On my web servers I have to also install GoDaddy's "intermediate certificate bundle". On the ASA I do not think that I will be able to preform anything like this. I do not fully understand what the "intermediate certificate bundle" does, but obviously it's important. So my question is can I use a GoDaddy SSL certificate on an ASA without my users getting any type of warning or error about connecting to a site that using an untrusted SSL certificate. I need this to be as simple as possible for my end users and warning messages are always scary :) Thanks!

  Read the article

• Cisco ASA 5510 ASDM: Setting up multiple public static ip addresses on a single interface and route

  - by ssjaken

  HI, i have a cisco ASA 5510 using ASDM version 6.3 We have a webserver that is been written very specifically and i was given super direct "DO NOT DEVIATE" directions. This server has to get traffic from 3 different PUBLIC ip's that we own. (our isp gave use a block of 12 static addresses) on 4 different ports. there are the directions i was given externalIP1:22 - 172.17.5.50:22 - SSH externalIP1:443 - 172.17.5.50:23040 - SIT externalIP2:443 - 172.17.5.50:33040 - STAGE externalIP3:443 - 172.17.5.50:43040 - PROD My first question is, using ASDM (my contract employer demands i use ASDM over CLI) how do i get three public addresses to work on one interface. We are authenticating on PPPoE. I know create a virtual interface with the static address but when i do i cannot ping the address from another offsite machine. secondly, where would i put the traffic redirect in. would i go ahead and create ACL's or just make NAT routes. Thanks.

  Read the article

• network is not available even when cisco vpn client is connected. wrong route?

  - by javapowered

  I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

  Read the article

• How to redirect logs from Cisco firewall to a specific file ?

  - by nitins

  We need to redirect the logs from our Cisco firewall(SA520-K9) to syslogd server(it's a CentOS server). The settings are done on the firewall. But the messages from firewall are going to /var/log/messages and console instead of /var/log/firewall.log which is our requirent. *.info;mail.none;authpriv.none;cron.none /var/log/messages authpriv.* /var/log/secure mail.* -/var/log/maillog cron.* /var/log/cron *.emerg * uucp,news.crit /var/log/spooler local7.* /var/log/firewall.log This is our syslog config file. Any advices ?

  Read the article

• Cisco login on-failure using syslog doesn't show username on failure?

  - by Jim

  interesting issue I am running into. I am trying to get syslog rmeote logging working with a Cisco switch. i have it working and logging for both on-success and on-failure. However when it is a failed login attempt it does not show the user name that tried to log in in the logs? Here is what the log looks like after a failed login: %SEC_LOGIN-4-LOGIN_FAILED: Login failed [user: ] [Source: 10.0. 0.6] [localport: 23] [Reason: Login Authentication Failed] Here is what I ahve in the sh run: login block-for 60 attempts 3 within 60 login delay 1 login on-failure log login on-success log archive log config logging enable notify syslog contenttype plaintext logging trap notifications logging facility local4 logging 10.0.0.8 aaa new-model aaa authentication login default local group tacacs+ aaa authorization config-commands aaa authorization exec default local group tacacs+

  Read the article

• How to statically configure DNS servers on a Cisco router when the WAN interface uses DHCP?

  - by Massimo

  I have a Cisco router (model 887VA, IOS 15.4) used to connect a LAN to the Internet via ADSL. The WAN interface uses DHCP: interface ATM0.1 point-to-point ip address dhcp I need the router to use a statically-defined DNS server for name resolution: ip name-server A.B.C.D However, the router insists on using the DNS servers supplied by the ISP via DHCP: Router#ping www.google.com Translating "www.google.com"...domain server (<ISP DNS>) [OK] Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 173.194.116.208, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 ms How can I tell the router to ignore the ISP-supplied DNS servers and only use the statically-configured one?

  Read the article

• How to get access to console to reset Cisco 3750?

  - by genehack

  I acquired two Cisco 3750 switches from another part of my organization. I was able to complete the standard password/config reset procedure on one without any issues -- boot it, put it into express config mode, telnet in, reset the passwords, etc. The second one doesn't ever boot to the point where it displays anything on the console. When power cycled, the 'SYST' light flashes green a few times, then comes on a solid green and stays lit. None of the other lights ever flash or light up. Holding down the 'MODE' button for up to 30 seconds produces no noticeable effects. Nothing ever comes out on the console. Since I was able to configure the first one without any problems, I know my connectinon is good -- console port configured right, good cable, etc. Is this just a hardware problem with the switch? Is there any way I can recover from this and get the switch back into a state where I can configure it?

  Read the article

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• Why do Cisco IOS routers hang in the middle of large downloads?

  - by cjavapro

  After a few years in use. We have seen Cisco 871 and 851 routers that would hang if you had a single download that was more than 100M large. It is intermittent. Sometimes the problem goes away, sometimes it happens on very small downloads (just a 10KB web page). It seems that the just about all the downloads eventually finish, but the bigger the download the longer the hang. Is there a way to resolve this? (short of router replacement which is what we have been doing)

  Read the article

• No Internet access while being connected to VPN using Cisco VPN Client 5.

  - by szeldon

  Hi, I have an access to corporate VPN using Cisco VPN Client 5.0.00:0340, but when I'm connected to it, I don't have an Internet access. I'm using Windows XP SP3. As it was suggested here http://forums.speedguide.net/showthread.php?t=209167 , I tried to enable "Allow local LAN Access" but it doesn't work. I also tried a second solution - deleting entry using "route" command, but it didn't help. I used "route delete 192.168.100.222". It's a third day of my attempts to solve this issue and I don't have an idea what else to do. I'm not very experienced in VPN stuff, but I know something about networking. Basing on my knowledge, I think that it's theoretically possible to achieve Internet access using my local network and only corporate stuff to be routed using VPN connection. I think that theoretically this should look like this: every IP being inside by corporation - VPN interface IP every other IP - my ethernet interface I've tried many possibilities of how to change those routes, but neither of them work. I'd really appreciate any help. My route configuration before connecting to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 192.168.101.254 192.168.100.222 10 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 1 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 3 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 192.168.101.254. =========================================================================== My route configuration after connection to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport 0x170006 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 10.251.6.1 10.251.6.51 1 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.0 255.255.255.0 10.251.6.1 10.251.6.51 10 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.1.150.10 255.255.255.255 192.168.101.254 192.168.100.222 1 10.251.6.0 255.255.255.0 10.251.6.51 10.251.6.51 20 10.251.6.51 255.255.255.255 127.0.0.1 127.0.0.1 20 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 10.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 10 192.168.100.0 255.255.254.0 10.251.6.1 10.251.6.51 10 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 10 213.158.197.124 255.255.255.255 192.168.101.254 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 30 224.0.0.0 240.0.0.0 10.251.6.51 10.251.6.51 20 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 10 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 10.251.6.1. ===========================================================================

  Read the article

• Cisco IOS router config -- how to disable SSH / SNMP on all but loopback address?

  - by chris

  Sorry for the naive question; a quick reading of the cisco docs doesn't answer this question... So I've got a router (say for the sake of argument a 4500 running IOS 15.x) It has interfaces in 3 different subnets -- 10.0.0.1/24, 10.0.1.1/24, and 10.0.2.1/24 It also has a loopback address of 172.16.0.33 How do I make it so that SSH / SNMP and other administrative traffic works on the 172 address but doesn't work on the IP addresses I wish to only use for L3 forwarding? Ideally this can be done by disabling the control plane access to these interfaces not just by using an ACL, but whatever, I don't actually care that much as long as it works... Thanks!

  Read the article

• VPN is working, except for DNS lookups. Firewall (Cisco ASA 5505) issue?

  - by macke

  I've got the following set up: LAN -> DHCP / DNS / VPN server (OSX 10.6) -> Cisco ASA 5505 -> WAN Connecting to the LAN via VPN works fine. I get all the details properly and I can ping any host on the internal network using their IP. However, I can't do any host lookups whatsoever. I've looked through the logs on and found this nugget in the firewall log: 3 Sep 08 2010 10:46:40 305006 10.0.0.197 65371 portmap translation creation failed for udp src inside:myhostname.local/53 dst inside:10.0.0.197/65371 Port 53 is dns services, no? Because of that log entry, I'm thinking that the issue is with the firewall, not the server. Any ideas? Please keep in mind that I have very little knowledge and experience with this kind of firewall and the little experience I do have is with the ASDM GUI console, not the CLI console.

  Read the article

• Cisco access list logging. Why is there a difference between IPv4 and IPv6?

  - by growse

  I've got a Cisco 877 router. I've got an IPv4 access list and an IPv6 access list set up and configured similar to this: interface Dialer1 ... ip access-group INTERET-IN ipv6 traffic-filter IPV6-IN Each of these access lists has a final rule of deny ip/ipv6 any any log. However, in my syslog I notice that there's a difference in formatting between the two types of entries. IPv4 will say: %SEC-6-IPACCESSLOGP: list INTERNET-IN denied udp 88.89.209.63(137) -> 1.2.3.4(137), 1 packet Whereas the IPv6 list will say %IPV6_ACL-6-ACCESSLOGNP: list IPV6-IN/240 denied 59 2001:0:5EF5:79FD:14F9:B773:3EBA:3EE3 (Dialer1) -> 2001:800:1000:0::1, 8 packets Both have broadly the same information, but the IPv6 log entry is missing the protocol type and port, both of which are very useful if I'm trying to troubleshoot connectivity. Why is this? How do I get IPv6 deny logs to display the protocol and port used, if any?

  Read the article

• Cisco WLAN Controller not pushing out DHCP addresses, what else could it be?

  - by Name

  On our Cisco WLAN Controller web interfaces, in Controller Interfaces, I have made a new interface with these settings: VLAN Identifier 202 IP Address 172.16.202.1 Netmask 255.255.255.0 Gateway 172.16.202.254 Primary DHCP Server 172.16.100.3 Secondary DHCP Server 172.16.100.2 Port: LAG I've also made a new WLAN and assigned it to the above interface. I have saved changes. But our wireless devices, although they seem to authenticate with the WLAN fine, they always get stuck on "obtaining DHCP address", so it seems the WLAN Controller isn't pushing out DHCP addresses to our devices. We do have a DHCP scope for the above in Windows Server 2008 R2 and everything there seems fine. If I connect a device with a static address (e.g. 172.16.202.10), it will connect. Stuck on what to do :(

  Read the article

• PARTNER WEBCAST (June 4): Enhance Customer experience with Nimble Storage SmartStack for Oracle with Cisco

  - by Zeynep Koch

  Live Webcast: Enhance Customer experience with Nimble Storage SmartStack for Oracle with Cisco A webcast for resellers who sell Oracle workloads to customers  Wednesday, June 4, 2014, 8:00 AM PDT /11 AM EDT  Register today Nimble Storage SmartStack™ for Oracle provides pre-validated reference architecture that speed deployments and minimize risk.  IT and Oracle administrators and architects realize the importance of underlying Operating System, Virtualization software, and Storage in maintaining services levels and staying in budget.  In this webinar, you will learn how Nimble Storage SmartStack for Oracle provides a converged infrastructure for Oracle database online transaction processing (OLTP) and online analytical processing (OLAP) environments with Oracle Linux and Oracle VM. SmartStack delivers the performance and reliability needed for deploying Oracle on a single symmetric multiprocessing (SMP) server or if you are running Oracle Real Application Clusters (RAC) on multiple nodes. Nimble Storage SmartStack for Oracle with Cisco can help you provide: Improved Oracle performance Stress-free data protection and DR of your Oracle database Higher availability and uptime Accelerate Oracle development and improve testing All for dramatically less than what you’re paying now Presenters: Doan Nguyen, Senior Principal Product Marketing Director, Oracle Vanessa Scott , Business Development Manager, Cisco Ibrahim “Ibby” Rahmani, Product and Solutions Marketing, Nimble Storage Join this event to learn from our Nimble Storage and Oracle experts on how to optimize your customers' Oracle environments. Register today to learn more!

  Read the article

• PARTNER WEBCAST (June 4): Enhance Customer experience with Nimble Storage SmartStack for Oracle with Cisco

  - by Zeynep Koch

  Live Webcast: Enhance Customer experience with Nimble Storage SmartStack for Oracle with Cisco A webcast for resellers who sell Oracle workloads to customers  Wednesday, June 4, 2014, 8:00 AM PDT /11 AM EDT  Register today Nimble Storage SmartStack™ for Oracle provides pre-validated reference architecture that speed deployments and minimize risk.  IT and Oracle administrators and architects realize the importance of underlying Operating System, Virtualization software, and Storage in maintaining services levels and staying in budget.  In this webinar, you will learn how Nimble Storage SmartStack for Oracle provides a converged infrastructure for Oracle database online transaction processing (OLTP) and online analytical processing (OLAP) environments with Oracle Linux and Oracle VM. SmartStack delivers the performance and reliability needed for deploying Oracle on a single symmetric multiprocessing (SMP) server or if you are running Oracle Real Application Clusters (RAC) on multiple nodes. Nimble Storage SmartStack for Oracle with Cisco can help you provide: Improved Oracle performance Stress-free data protection and DR of your Oracle database Higher availability and uptime Accelerate Oracle development and improve testing All for dramatically less than what you’re paying now Presenters: Doan Nguyen, Senior Principal Product Marketing Director, Oracle Vanessa Scott , Business Development Manager, Cisco Ibrahim “Ibby” Rahmani, Product and Solutions Marketing, Nimble Storage Join this event to learn from our Nimble Storage and Oracle experts on how to optimize your customers' Oracle environments. Register today to learn more!

  Read the article

• How to whitelist external access to an internal webserver via Cisco ACLs?

  - by Josh

  This is our company's internet gateway router. This is what I want to accomplish on our Cisco 2691 router: All employees need to be able to have unrestricted access to the internet (I've blocked facebook with an ACL, but other than that, full access) There is an internal webserver that should be accessible from any internal IP address, but only a select few external IP addresses. Basically, I want to whitelist access from outside the network. I don't have a hardware firewall appliance. Until now, the webserver has not needed to be accessible externally... or in any case, the occasional VPN has sufficed when needed. As such, the following config has been sufficient: access-list 106 deny ip 66.220.144.0 0.0.7.255 any access-list 106 deny ip ... (so on for the Facebook blocking) access-list 106 permit ip any any ! interface FastEthernet0/0 ip address x.x.x.x 255.255.255.248 ip access-group 106 in ip nat outside fa0/0 is the interface with the public IP However, when I add... ip nat inside source static tcp 192.168.0.52 80 x.x.x.x 80 extendable ...in order to forward web traffic to the webserver, that just opens it up entirely. That much makes sense to me. This is where I get stumped though. If I add a line to the ACL to explicitly permit (whitelist) an IP range... something like this: access-list 106 permit tcp x.x.x.x 0.0.255.255 192.168.0.52 0.0.0.0 eq 80 ... how do I then block other external access to the webserver while still maintaining unrestricted internet access for internal employees? I tried removing the access-list 106 permit ip any any. That ended up being a very short-lived config :) Would something like access-list 106 permit ip 192.168.0.0 0.0.0.255 any on an "outside-inbound" work?

  Read the article

• How can I configure multiple default gateways on a CISCO Router?

  - by Spirit

  Does any one knows a way to configure a cisco router with multiple gateways - multiple gateways of last resort? I've tried adding a gateway of last resort twice (with different metric) but only one is shown: Router(config)# ip route 0.0.0.0 0.0.0.0 2.2.2.2 10 Router(config)# ip route 0.0.0.0 0.0.0.0 3.3.3.3 100 And the show ip route output was: Router# show ip route Gateway of last resort is 2.2.2.2 to network 0.0.0.0 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, FastEthernet0/0 3.0.0.0/24 is subnetted, 1 subnets C 3.3.3.0 is directly connected, FastEthernet0/1 32.0.0.0/30 is subnetted, 1 subnets C 32.2.2.0 is directly connected, Serial0/2/0 S* 0.0.0.0/0 [10/0] via 2.2.2.2 The point is that i cannot see the other route with higher distance metric? Anyone has a sugestion? I mean will this config work if the link on 2.2.2.2 fails? Will the router choose the other network 3.3.3.3, if the link 2.2.2.2 fails?

  Read the article

• How do you change a Cisco ASA 5510 management interface?

  - by Sam Sanders

  I want to add a redundant interface to my Cisco ASA 5510. The management interface is currently using Ethernet0/1 (10.1.25.254/24) one of the interface I want to use for the redundant interfaces. So I wanted to setup Management0/0 as the new management interface. The other interface I want to use is Ethernet0/2 (10.1.0.254/24) for the redundant interface. The Ethernet0/3 (10.1.251.5/24) interface is not going to be part of the redundant interface. I gave the Management0/0 an IP address of 10.1.254.5, and was able to connect a win7 box to Management0/0 and use 10.1.254.5 as a gateway; and ping another address on the (10.1.251.0/24) network, but I can't ping the interface (10.1.254.5) itself. I also can't use ASDM/SSH to log onto the ASA at 10.1.254.5. I setup rules in Configuration Device Management Management Access ASDM/HTTPS/Telnet/SSH. That look like the original rules for the Ethernet0/1 interface. The last thing I can think to try would be to change the Configuration Device Management Management Access Management Interface. I'm a bit nervous about changing it, the description of it is a bit vague. What it's going to do if I change it? What is the correct way to change a management interface?

  Read the article

• Cisco 851 (IOS) router: FastEthernet 4 (WAN) got the shutdown flag.

  - by cjavapro

  At a customer location there was a Cisco 851 router (which uses IOS). The PCs on location were all of a sudden unable to connect. We came on site and found that FastEthernet 4 (the WAN port) was "administratively down". We ran these commands to resolve it config t interface fa4 no shutdown exit exit write Now the mystery is how the shutdown flag got there in the first place? The router was on battery backup... but during the outage it was power cycled by the customer. It is possible that there was a short outage by the ISP and that the power cycle caused the shutdown flag to come up. There may have been a hack or an attack pattern that caused the shutdown flag to come up. There may have been a hack or an attack pattern that the router to become unavailable and then caused the shutdown flag to be added on startup. Question: Does anybody have any clues? or at least remember that they had a shutdown flag come up on their WAN port also?

  Read the article

• Two cisco gigabit switches refuse to link to each other. Any idea why?

  - by Prody

  I have 3 Linksys SR2024 switches which are basically non-managed 24 port Gbit + 2 miniGBIC. I now had to add another switch to the network, and my provider didn't have the SR2024 switch anymore, so I got the Cisco SLM2024 which was a bit more expensive. It's pretty much the same thing but with management (that I don't need). So I've connected the SLM2024 to a SR2024 via Cat6 cable, and for some strange reason, I get no link. If I connect any machine with a Gbit NIC to both switches, it links with 1Gbit autonegotiated. If I connect the SLM2024 to a non-Gbit switch (I have a cheap 4port ASUS switch), it will link just fine on 100Mbit full duplex. Since the SLM2024 has management, I've tried to see if something is misconfigured on it's side, but it's not, it advertises 1Gbit and lower. (hence the machines connecting succesfully at 1Gbit). Since the SR2024 that I'm trying to connect it to also connects successfully with another SR2024 and other Gbit machines, it means that it advertises Gbit too. But for some reason when I link the SR2024 to the SLM2024 I get no link. Please note that I've properly tested the wire. Does anyone have any idea what's wrong?

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >