Search Results

Search found 1557 results on 63 pages for 'daniel lorch'.

Page 17/63 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Recover a lost IBM DS4300 SAN password?

  - by Daniel

  I have a pair of IBM DS4300 SAN units that I need to perform a firmware upgrade on. Unfortunately the admin passwords on these units have been lost and now need to be reset. I had hoped the default password of 'infiniti' would work but it seems that it must have been changed. I know the method here is to contact IBM but the cost of that phone call is ludicrous if someone out here knows what they're going to tell me to do. These units are out of warranty and the cost of support is beyond what we have the budget for. Is there an interrupt I can enter during the boot process (similar to a cisco password recovery) or is there a hardware/software tool I require? Please, if anyone has ever gone through the process of an IBM password recovery I’m asking for a little help. EDIT: Just to clarify, the password I need to reset is the one used for serial cable access and not for storage manager. Sorry if I have caused more confusion.

  Read the article

• Airport Extreme roaming setup

  - by Daniel Johansson

  We've got three Apple AirPort extremes and want to setup them as a roaming wlan network on my company. My question is what's the correct setup for this? All three AP:s is supposed to create the same wireless network "MyWlan" and we want roaming supoprt between them so that client can move from floor to floor without having to switch wlan or reconnect. We don't want to use any kind of DHCP or NAT on the AirPorts, only bridge mode. Do we connect the AirPorts to the lan/ethernet using the WAN port or one of the LAN ports? What's the correct settings in the config utility? Have one of the AirPorts create a network and setup the other two to extend the created network from AirPort 1 or have them all create the same network and set the same wlan password?

  Read the article

• Open Office crashes, recovers, crashes again

  - by Daniel R Hicks

  After completely reinstalling my laptop due to apparent registry corruption, I've encountered a problem with Open Office: I open a simple Calc spreadsheet, it comes up normally, but then after anywhere from 5 seconds to several minutes (without even touching the Calc window) OO crashes, then comes up through recovery. If I let it "recover" it will do so and bring the spreadsheet up again, only to repeat the crash scenario again. If I kept clicking "OK" it would apparently do this all day. I reinstalled OO once and the problem went away for awhile, but it came back. I then attempted to "reset" my profile (ie, rename the OO user directory in App Data), but OO crashed during the first startup after that, then resumed the original behavior. If I open the same file using Excel it complains of errors in the file, and "recovers" them, but the "error report" it generates contains no details. If I save the "recovered" file then OO Calc will open it, but the problem returns after saving again. Any ideas? (The system is Vista SP2, running OO 3.4.1) How to reproduce: Start Open Office Calc. Save workspace as "CrashTest.ods" From Task Manager kill Open Office (soffice.exe/bin -- one of each) Double click on the saved "CrashTest.ods" in Explorer. OO puts up a message that recovery will occur -- allow it. When the Calc window comes up, don't touch it -- just wait about 10 seconds. Calc window closes and OO puts up a message that recovery will occur -- from now on the sequence will repeat. I suspect this behavior is limited to a few (recent) versions of OO, and very possibly only Calc. Reported as Open Office Bug 1211094. Sigh!! As much as it irritates me, I'm having to switch over to Excel for several things I used to do with Calc. Excel has a miserable UI, but at least it says up for longer than 10 seconds.

  Read the article

• uploading a python site to httpdocs?

  - by daniel Crabbe

  OK - so we've agreed to host a python site, got the files and not sure where to go next. We use a dedicated server and manage it mainly with plesk which has a tick box for a python support but not sure what this does. This is all the info i have from previous hosts; 10,000 ft overview The site is intended to run on a Linux host, specifically Ubuntu Server (tho it should be fine on most distros). The web framework is CherryPy ( http://cherrypy.org/ ), which is a Python based framework. There is no database as such, instead the data is kept in JS files and loaded by the front end. nicholasbarker.com.c6a4facf0192/www/js/video_content_items.js is a prime example of this. The main site templates are in nicholasbarker.com.c6a4facf0192/www/templates/ They are Cheetah templates ( http://www.cheetahtemplate.org/ ) and here's the file structure i've been sent - Could some explain to me how i'd go about uploading and running this site... Any help welcome! Dc

  Read the article

• Best way to compress avi files for web viewing and best format for view

  - by Daniel

  What is the best tool for reducing the file size of AVI files to post for viewing on the web? Also what is the recommended format?

  Read the article

• mac osX file recovery

  - by Daniel

  I thought that all operating systems would merge folder content when being moved to the same location. Imagine my surprise when that didn't happen and I have hundreds, if not thousands of files that have gone missing and are nowhere to be found. Because they were not "deleted" they are not in the trash bin. I've tried to do some recovery using a program called stellarPheonix but after about a 24hour scan, it didn't recognize any of the raw files (.dng,.arw) as image files and so I couldn't see if they could be recovered. It also didn't show the directory structure, which would be handy. I tried a quick scan, but all it showed was files that were still on the HD, not sure what the point of that is. I've used recover 2000 on Win and it does a good job, does anyone know of anything that works quickly and reliably for this kind of file recovery. (I don't think I should have to do a sector-by=sector for this kind of file loss)

  Read the article

• Windows 7 remote desktop connection does not respond to mouse or keyboard

  - by Daniel Jette

  Pretty much every time I connect to my work PC from home (both running Windows 7), I can see the screen refresh and signs of life (clock changes, notifications pop up), but I cannot interact with the remote machine at all. Mouse and keyboard input are both ignored. If I repeatedly reconnect, I will eventually get a connection that works. I think either a setting on my host machine, VPN client or work network is configured wrong. My home PC is running Windows 7 Professional. My work PC is running Windows 7 Enterprise. My VPN client is Cisco AnyConnect. Is this a problem anyone else has run in to? Any suggestions for settings to tweak?

  Read the article

• RRAS server 2003 one nic vpn encrypted

  - by Daniel Woodhead

  Hi All, I have a a machine installed with Server 2003 standard on it. It is behind a standard adsl router. I have setup RRAS access on it with under the custom setting and selected just vpn as the machine only has one nic installed. I can connect to the server and it all works fine. I'm just wondering where the settings are to say that it is data encrypted. I know in xp when setting up a vpn you can check the option to encrypt the data, but doing this in server 2003 there isn't the option so thought i would try and use rras. The main reason that i want to do this is that xp only allows one connection at a time. Dan

  Read the article

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• kill -9 doesn't work

  - by Daniel

  I have a server with 3 oracle instances on it, and the file system is nfs with netapp. After shutdown the databases, one process for each database doesn't quit for a long time. Each kill -i doesn't work. I tried to truss, pfile it, the command through error. And iostat shows there are lots of IO to the netapp server. So someone said the process was busy writing data to remote netapp server, and before the write complete, it won't quit. So what need to be done was just wait until all the IO was done. After wait for longer time (about 1.5 hours), the processes exit. So my question is: how can a process ignore the kill signal? As far as I know, if we kill -9, it will stop immediately. Do you encounter such situation kill -i doesn't kill the process right away? TEST7-stdby-phxdbnfs11$ ps -ef|grep dbw0 oracle 1469 25053 0 22:36:53 pts/1 0:00 grep dbw0 oracle 26795 1 0 21:55:23 ? 0:00 ora_dbw0_TEST7 oracle 1051 1 0 Apr 08 ? 3958:51 ora_dbw0_TEST2 oracle 471 1 0 Apr 08 ? 6391:43 ora_dbw0_TEST1 TEST7-stdby-phxdbnfs11$ kill -9 1051 TEST7-stdby-phxdbnfs11$ ps -ef|grep dbw0 oracle 1493 25053 0 22:37:07 pts/1 0:00 grep dbw0 oracle 26795 1 0 21:55:23 ? 0:00 ora_dbw0_TEST7 oracle 1051 1 0 Apr 08 ? 3958:51 ora_dbw0_TEST2 oracle 471 1 0 Apr 08 ? 6391:43 ora_dbw0_TEST1 TEST7-stdby-phxdbnfs11$ kill -9 471 TEST7-stdby-phxdbnfs11$ ps -ef|grep dbw0 oracle 26795 1 0 21:55:23 ? 0:00 ora_dbw0_TEST7 oracle 1051 1 0 Apr 08 ? 3958:51 ora_dbw0_TEST2 oracle 471 1 0 Apr 08 ? 6391:43 ora_dbw0_TEST1 oracle 1495 25053 0 22:37:22 pts/1 0:00 grep dbw0 TEST7-stdby-phxdbnfs11$ ps -ef|grep smon oracle 1524 25053 0 22:38:02 pts/1 0:00 grep smon TEST7-stdby-phxdbnfs11$ ps -ef|grep dbw0 oracle 1526 25053 0 22:38:06 pts/1 0:00 grep dbw0 oracle 26795 1 0 21:55:23 ? 0:00 ora_dbw0_TEST7 oracle 1051 1 0 Apr 08 ? 3958:51 ora_dbw0_TEST2 oracle 471 1 0 Apr 08 ? 6391:43 ora_dbw0_TEST1 TEST7-stdby-phxdbnfs11$ kill -9 1051 471 26795 TEST7-stdby-phxdbnfs11$ ps -ef|grep dbw0 oracle 1528 25053 0 22:38:19 pts/1 0:00 grep dbw0 oracle 26795 1 0 21:55:23 ? 0:00 ora_dbw0_TEST7 oracle 1051 1 0 Apr 08 ? 3958:51 ora_dbw0_TEST2 oracle 471 1 0 Apr 08 ? 6391:43 ora_dbw0_TEST1 TEST7-stdby-phxdbnfs11$ truss -p 26795 truss: unanticipated system error: 26795 TEST7-stdby-phxdbnfs11$ pfiles 26795 pfiles: unanticipated system error: 26795

  Read the article

• Issues with Rsync on a NAS

  - by Daniel Fischer

  I'm trying to rsync a few external hard drives over to my new Nas DS412+ but I'm noticing it's stupid slow. I'm trying it via mounting the backup folder via afb on a Mac. I was told this may be the wrong way to do it. I recently just turned on "network backup" on the Synology and am now running rsync over ssh like: rsync -ar --progress . admin@localip:/backup/path Is this the right way to do it now? Will it be faster? Is there something else I can do to make it faster? Edit: I'm getting a ton of: "failed to set permissions" "failed to set times" now that I run it. What do I do?

  Read the article

• KVM Guest with NAT + Bridged networking

  - by Daniel

  I currently have a few KVM Guests on a dedicated server with bridged networking (this works) and i can successfully ping the outside ips i assign via ifconfig (in the guest). However, due to the fact i only have 5 public ipv4 ip addresses, i would like to port forward services like so: hostip:port - kvm_guest:port UPDATE I found out KVM comes with a "default" NAT interface, so added the virtual NIC to the Guest virsh configuration then configured it in the Guest, it has the ip address: 192.168.122.112 I can successfully ping 192.168.122.112 and access all ports on 192.168.122.112 from the KVM Host, so i tried to port forward like so: iptables -t nat -I PREROUTING -p tcp --dport 5222 -j DNAT --to-destination 192.168.122.112:2521 iptables -I FORWARD -m state -d 192.168.122.0/24 --state NEW,RELATED,ESTABLISHED -j ACCEPT telnet KVM_HOST_IP 5222 just hangs on "trying" telnet 192.168.122.112 2521 works [root@node1 ~]# tcpdump port 5222 tcpdump: WARNING: eth0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:43:47.216181 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445777813 ecr 0,sackOK,eol], length 0 23:43:48.315747 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445778912 ecr 0,sackOK,eol], length 0 23:43:49.415606 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445780010 ecr 0,sackOK,eol], length 0 7 packets received by filter 0 packets dropped by kernel [root@node1 ~]# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state NEW,RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT) target prot opt source destination All help is appreciated. Thanks.

  Read the article

• Why do my speakers get distorted randomly on Windows 7?

  - by Daniel Fischer

  I have a studio monitor setup. I have 2 KRK 6's and a Focusrite Firewire Pro 24. Every few hours my speakers sound distorted and my solution has been go to sound levels Properties of Saffire Audio Device Advanced Default Format Toggle to 16 bit then back to 24bit. Why does it screw up every few hours? Sometimes one speaker doesn't output too and this same process resets it but that's more rare. Is this a OS issue or Focusrite Driver Issue?

  Read the article

• Intermittent PHP error: Undefined function <core function>

  - by Daniel

  In the last week I've been coming across an incredibly annoying error on one of Slicehost slices. It appears that every now and then PHP will fail with a fatal error, saying a certain function is undefined. The function changes, but is always a core PHP function e.g. defined(), version_compare(), etc. This problem has occurred while using several different PHP applications - PHPMyAdmin, my own custom built apps, etc, leading me to believe that the problem is not specific to the running code. Here are some details: - Debian Lenny - Apache 2.2.9 - PHP 5.2.6-1+lenny4 with Suhosin-Patch (running eAccelerator 0.9.6) Apache and PHP are installed from Debian packages. Error logs show nothing out of the ordinary. I thought memory might be an issue, but free -m reports upwards of 100MB free almost all the time. Another thing I'm trying to investigate is if the problem might be related to eAccelerator, but testing this theory out is incredibly hard because the issue doesn't appear very often and I've been using eAccelerator for months on this install without any problems up until now. Has anyone ever come across anything like this? Why would PHP report undefined core functions?

  Read the article

• Gigabyte GA-P55A-UD4P won't boot from USB drive with RAID enabled

  - by Daniel Schaffer

  I've got a Windows 7 installation image on my USB hard drive, which is set up to be bootable. I know it works because I've used it on several computers, and it works on the computer I'm trying to install as long as the RAID controller is disabled. However, when I enable the RAID controller and attempt to boot from the USB driver, it hangs for 30-60 seconds and then gives me the "disk boot failure, insert system disk" error like it can't find any OS. Just for laughs, I disabled the RAID controller again and it booted fine. I'm having separate, unrelated issues burning a dvd with the ISO, so I would prefer to get this working.

  Read the article

• Unusual Caching Issue with IE 7/8 and IIS 7

  - by Daniel A. White

  We recently moved a site into production running Server 2008 x64 and IIS 7. The ASP.NET pages apparently load just fine, but when it comes to IE 7 and 8, a weird caching issue has cropped up with the CSS and JavaScript files on the page. On a very sporadic schedule, IE does not get all the files necessary to compose the page (i.e. CSS and JS files). When I manually go to the missing files from the address bar, they come back from local cache as empty. I F5 these source files and magically they come down properly. I refresh the site after loading a few files and the cache seems to hold. This problem has only been reproduced (again, sporadically) on IE 7 and 8 running XP. Chrome and Firefox appear to be immune. We have set IIS to use server-side kernel caching for CSS, JS and images. We also have set to expire content for the App_Themes and Scripts directories to expire immediately. One initial thought it was a SWF loading an FLV on page load. These fixes have not remedied the problem. We had no problems on our staging server which is using Server 2003 and IIS 6. Any ideas would be greatly appreciated. P.S. It sounds similar to this problem: but we do have the Static Content module installed. http://serverfault.com/questions/115099/iis-content-length-0-for-css-javascript-and-images

  Read the article

• Does VPN connection on virtual machine bypass host VPN?

  - by Daniel Valland Torgrimsen

  I wanted to see if i could channel my traffic trough two vpns, so as an experiment i set up a windows xp virtual machine in virtualbox (using NAT shared network setting), connected the host pc(windows 7) to a vpn, and then the virtual machine to another vpn. this seams to work fine. However, my question is, is the traffic sent trough both vpn servers, or is the virtual machines vpn bypassing the host machines vpn connection? thanks.

  Read the article

• Mac OS X file recovery

  - by Daniel

  I thought that all operating systems would merge folder content when being moved to the same location. Imagine my surprise when that didn't happen and I have hundreds, if not thousands of files that have gone missing and are nowhere to be found. Because they were not "deleted" they are not in the trash bin. I've tried to do some recovery using a program called stellarPheonix but after about a 24hour scan, it didn't recognize any of the raw files (.dng,.arw) as image files and so I couldn't see if they could be recovered. It also didn't show the directory structure, which would be handy. I tried a quick scan, but all it showed was files that were still on the HD, not sure what the point of that is. I've used recover 2000 on Win and it does a good job, does anyone know of anything that works quickly and reliably for this kind of file recovery. (I don't think I should have to do a sector-by=sector for this kind of file loss)

  Read the article

• UAC-account-users can't see their mounted network-drives

  - by Daniel

  I wrote a few login batches in the Group Policy Management which mount specified devices to specified usergroups. The batches work as they should as long UAC is disabled. My problem is that the UAC-account-users can't see their mounted network-drives because the login scripts run in elevated context. I tried to fix the problem with PsExec (-l) so that the network-folders are mapped with limited user rigths. But it seems that this won't work. (PsExec is already installed on all computers so it can work local.) Has anyone an idea how to fix that problem? I spended a long time in trying to fix the problem but I did not find any solutions about THIS problem.

  Read the article

• How to use dpkg of busybox

  - by Daniel YC Lin

  I'm trying to install pkg in a limited space embedded system. I use busybox's dpkg. To let dpkg work, I just touch a file touch /var/lib/dpkg/status But, it still can not work. $dpkg -i ntpdate_4.2.4p4+dfsg-8lenny3_sh4.deb dpkg: package ntpdate depends on netbase, which is not installed or flagged to be installed How to flag the netbase as installed?

  Read the article

• Is there any way to detect when nginx has completed a graceful shutdown?

  - by Daniel Vandersluis

  I have a ruby on rails application which is running on passenger and nginx, with one main webserver and multiple application servers. I am trying to update my deployment process in order to minimize (or ideally, remove) any downtime caused by the deployment. The main roadblock right now is that passenger takes some time to restart (ie. reload the application), so in order to get around this, I want to stagger my restarts so that only one app server gets restart at a time. In order to do this without losing any long running passenger processes, I am thinking I need to gracefully shutdown the app server's nginx instance, which will cause it to no longer accept new connections but continue to process the existing ones; as well, HAProxy will detect that the app server is down and route new requests to the other server. However, assuming that there is a long-running process, I am not sure how to detect when the graceful shutdown has completed so that I can start it back up. Since the shutdown is caused by sending a signal (ie. kill -QUIT $( cat /var/run/nginx.pid )), and the kill command will return immediately, I cannot combine commands (ie. kill ... && touch restarted), as the touch command will execute immediately, even if nginx hasn't completed its shutdown. Is there any good way to do this?

  Read the article

• Small domain names

  - by Daniel Moura

  I'm want to register a small domain name. I want it to be easy to use from a mobile phone. The '.com' extension is hard to use because you have to press 'o' then 'm'. Does anyone has any suggestions of small domain extension names and where to buy?

  Read the article

• Moving from Ubuntu desktop to Ubuntu Server via SSH

  - by Daniel Elessedil Kjeserud

  So a little while ago I installed regular Ubuntu for a home server, but that gave me a lot of extra packages. What I should have done was to install Ubuntu Server, since I don't even own a screen to connect to it. Does anybody know of a way to convert my Ubuntu machine to a Ubuntu Server machine in one big swoop? It has to be done over SSH, since I don't have a screen to connect to it, like I said. It's currently running 9.10, about to be upgraded to 10.4.

  Read the article

• PHP-FPM not working with nginx and CentOS

  - by Daniel

  After failing to get FastCGI to work with PHP I have installed the PHP-FPM service which is reported to work out of the box, however PHP files are downloading instead of executing. This is what I have in the nginx.conf file: server { listen 80; server_name pubserver; root /usr/share/nginx/html; location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/nginx/html$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; include /etc/nginx/fastcgi_params; } } The command netstat -tulpn | grep :9000 displays this which suggests PHP-FPM is running: tcp 0 0 127.0.0.1:9000 0.0.0.0:* LISTEN 1058/php-fpm.conf)

  Read the article

• Remap "next song" key in ubuntu to work with spotify and wine

  - by daniel-magnussons

  I want to change song in spotify with a global key in ubuntu. This is possible on windows with a special key on keyboard, the "next song key"(?) How can I remap a key in ubuntu(no "next song" button here) to work as "next song" button? like "ctrl +right key". And how would i do to make this work with spotify, which is running thru wine? Basically i want to know what the ascii code for "next song" button is, and how do i map it to a key combination under ubuntu. And hope it routes this command thru wine without problem. Edit: I don't have the "next song" button on the ubuntu machine.

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >