Search Results

Search found 3574 results on 143 pages for 'difficult'.

Page 17/143 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Use autocomplete in dropdown cells with Excel 2007?

    - by Martin
    I want to make a survey with Excel and I therefore have defined the cells for the answers as a dropdown cell which only accepts answers from a certain list, e. g.: The two Lists List1 and List2 (yellow cells) are the possible answers for the questions in Block 1.x resp. 2.x (blue) . There might be a block 4 with more questions, which again use List1 for their possible answers. My problem is: I'd like to be able to use the autocompleate feature to fill in the blue cells with the dropdown menu, so that the user only types 5 and it automatically expands to "5: extremely important" or "5: extremely difficult". According to my research on the www, this should be possible if I add the list with possible answers directly above the cells where autocomplete should work (I did this with the green helper cells which could be hidden) . But I have to enter at least 4 characters 5: e to get the autocompleted suggestion. Is there a way to make autocomplete already replace a "5" by the corresponding valid term? As the survey file shall be distributed to a lot of people "outside", I can not use VBA magic because it may be blocked on their computer and might not work. EDIT: it seems to have to do with the numbers I use: If I'd start my List items with A, B, C instead of 1, 2, 3, it would work perfectly. Excel seems to ignore the pure numbers when they are entered and does not try to autocomplete them.. is there a workaround? (I hope it is clear what I want, it seems a little difficult to explain.)

    Read the article

  • Standing and sitting while using a computer at work

    - by Adam Batkin
    I would like to be able to comfortably switch between sitting and standing while at work (I'm a software developer, so I spend most of my day in front of a computer). For the past couple of months I have been using a large elevated stand that sits on my desk (designed expressly for this purpose) containing my keyboard and mouse, and my monitors have been raised as high as possible and aimed upwards. So I can stand all day and I'm pretty comfortable (my right wrist may be at too much of an angle when it's on my mouse, but that's a separate issue). The only problem is that sometimes I want to be able to sit. I can easily place my keyboard and mouse back down under the elevated stand, but I have to look up pretty steeply and that is uncomfortable and makes it difficult to see the screens since they are tilted upwards. My monitor mounts are difficult to adjust quickly/easily, so I can't just re-aim them. I would of course love one of those hydraulic standing/sitting desks (cost isn't the problem). But I'm in a row of "trader-style" desks where it's basically a very long surface with people sitting at 6-foot intervals. What type of equipment do you recommend? I suppose the best thing would be some sort of monitor stand (it must be able to hold 2-3 LCDs) that can easily be lowered and raised. But any other suggestions are also welcome.

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Exchange 2003 inbound routing issue

    - by user565712
    Just recently we started experiencing inbound routing issues. Email adddressed to [email protected] is intermittantly translated to [email protected]. This is happening for several users and, as stated, is intermittant. I don't know where to start looking for the solution. Is this an Exchange issue? A DNS issue? We have a single Exchange server inside our network with an FQDN of server.domain.local with a single SMTP Virtual Server. The Advanced properties of the Delivery tab of the Virt Server has an empty Masquerade Domain textbox and the value for the FDQN text-box is set to the domain itself, domain.com. The DNS record for domain.com is a CNAME entry referencing www.domain.com. Is this somehow related to the problem? I checked the headers of the inbound messages that generated NDRs as a result of being sent to [email protected] and nowhere in the header is www.domain.com mentioned. To make my life even more difficult, we use Postini as a third-party SPAM filtering service. Our MX records point to the Postini servers and Postini delivers the messages to our server. Perhaps it is Postini that is mucking things up? sigh I'm having trouble with this one and the intermittent aspect is making it that much more difficult for me. Any ideas?

    Read the article

  • SQL – NuoDB and Third Party Explorer – SQuirreL SQL Client, SQL Workbench/J and DbVisualizer

    - by Pinal Dave
    I recently wrote a four-part series on how I started to learn about and begin my journey with NuoDB. Big Data is indeed a big world and the learning of the Big Data is like spaghetti – no one knows in reality where to start, so I decided to learn it with the help of NuoDB. You can download NuoDB and continue your journey with me as well. Part 1 – Install NuoDB in 90 Seconds Part 2 – Manage NuoDB Installation Part 3 – Explore NuoDB Database Part 4 – Migrate from SQL Server to NuoDB …and in this blog post we will try to answer the most asked question about NuoDB. “I like the NuoDB Explorer but can I connect to NuoDB from my preferred Graphical User Interface?” Honestly, I did not expect this question to be asked of me so many times but from the question it is clear that we developers absolutely want to learn new things and along with that we do want to continue to use our most efficient developer tools. Now here is the answer to the question: “Absolutely, you can continue to use any of the following most popular SQL clients.” NuoDB supports the three most popular 3rd-party SQL clients. In all the leading development environments there are always more than one database installed and managing each of them with a different tool is often a very difficult task. Developers like to use one tool, which can control most of the databases. Once developers are familiar with one database tool it is very difficult for them to switch to another tool. This is particularly difficult when we developers find that tool to be the key reason for our efficiency. Let us see how to install each of the NuoDB supported 3rd party tools along with a quick tutorial on how to go about using them. SQuirreL SQL Client First download SQuirreL Universal SQL client. On the Windows platform you can double-click on the file and it will install the SQuirrel client. Once it is installed, open the application and it will bring up the following screen. Now go to the Drivers tab on the left side and scroll it down. You will find NuoDB mentioned there. Now right click over it and click on Modify Driver. Now here is where you need to make sure that you make proper entries or your client will not work with the database. Enter following values: Name: NuoDB Example URL: jdbc:com:nuodb://localhost:48004/test Website URL: http://www.nuodb.com Now click on the Extra Class Path tab and Add the location of the nuodbjdbc.jar file. If you are following my blog posts and have installed NuoDB in the default location, you will find the default path as C:\Program Files\NuoDB\jar\nuodbjdbc.jar. The class name of the driver is automatically populated. Once you click OK you will see that there is a small icon displayed to the left of NuoDB, which shows that you have successfully configured and installed the NuoDB driver. Now click on the tab of Alias tab and you can notice that it is empty. Now click on the big Plus icon and it will open screen of adding an alias. “Alias” means nothing more than adding a database to your system. The database name of the original installation can be anything and, if you wish, you can register the database with any other alternative name. Here are the details you should fill into the Alias screen below. Name: Test (or your preferred alias) Driver: NuoDB URL: jdbc:com:nuodb://localhost:48004/test (This is for test database) User Name: dba (This is the username which I entered for test Database) Password: goalie (This is the password which I entered for test Database) Check Auto Logon and Connect at Startup and click on OK. That’s it! You are done. On the right side you will see a table name and on the left side you will see various tabs with all the relevant details from respective table. You can see various metadata, schemas, data types and other information in the table. In addition, you can also generate script and do various important tasks related to database. You can see how easy it is to configure NuoDB with the SQuirreL Client and get going with it immediately. SQL Workbench/J This is another wonderful client tool, which works very well with NuoDB. The best part is that in the Driver dropdown you will see NuoDB being mentioned there. Click here to download  SQL Workbench/J Universal SQL client. The download process is straight forward and the installation is a very easy process for SQL Workbench/J. As soon as you open the client, you will notice on following screen the NuoDB driver when selecting a New Connection Profile. Select NuoDB from the drop down and click on OK. In the driver information, enter following details: Driver: NuoDB (com.nuodb.jdbc.Driver) URL: jdbc:com.nuodb://localhost/test Username: dba Password: goalie While clicking on OK, it will bring up the following pop-up. Click Yes to edit the driver information. Click on OK and it will bring you to following screen. This is the screen where you can perform various tasks. You can write any SQL query you want and it will instantly show you the results. Now click on the database icon, which you see right on the left side of the word User=dba.  Once you click on Database Explorer, you can perform various database related tasks. As a developer, one of my favorite tasks is to look at the source of the table as it gives me a proper view of the structure of the database. I find SQL Workbench/J very efficient in doing the same. DbVisualizer DBVisualizer is another great tool, which helps you to connect to NuoDB and retrieve database information in your desired format. A developer who is familiar with DBVisualizer will find this client to be very easy to work with. The installation of the DBVisualizer is very pretty straight forward. When we open the client, it will bring us to the following screen. As a first step we need to set up the driver. Go to Tools >> Driver Manager. It will bring up following screen where we set up the diver. Click on Create Driver and it will open up the driver settings on the right side. On the right side of the area where it displays Driver Settings please enter the following values- Name: NuoDB URL Format: jdbc:com.nuodb://localhost:48004/test Now under the driver path, click on the folder icon and it will ask for the location of the jar file. Provide the path as a C:\Program Files\NuoDB\jar\nuodbjdbc.jar and click OK. You will notice there is a green button displayed at the bottom right corner. This means the driver is configured properly. Once driver is configured properly, we can go to Create Database Connection and create a database. If the pop up show up for the Wizard. Click on No Wizard and continue to enter the settings manually. Here is the Database Connection screen. This screen can be bit tricky. Here are the settings you need to remember to enter. Name: NuoDB Database Type: Generic Driver: NuoDB Database URL: jdbc:com.nuodb://localhost:48004/test Database Userid: dba Database Password: goalie Once you enter the values, click on Connect. Once Connect is pressed, it will change the button value to Reconnect if the connection is successfully established and it will show the connection details on lthe eft side. When we further explore the NuoDB, we can see various tables created in our test application. We can further click on the right side screen and see various details on the table. If you click on the Data Tab, it will display the entire data of the table. The Tools menu also has some very interesting and cool features like Driver Manager, Data Monitor and SQL History. Summary Well, this was a relatively long post but I find it is extremely essential to cover all the three important clients, which we developers use in our daily database development. Here is my question to you? Which one of the following is your favorite NuoDB 3rd-Party Database Client? (Pick One) SQuirreL SQL Client SQL Workbench/J DbVisualizer I will be very much eager to read your experience about NuoDB. You can download NuoDB from here. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Big Data, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: NuoDB

    Read the article

  • SQL SERVER – Weekly Series – Memory Lane – #033

    - by Pinal Dave
    Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2007 Spatial Database Definition and Research Documents Here is the definition from Wikipedia about spatial database : A spatial database is a database that is optimized to store and query data related to objects in space, including points, lines and polygons. While typical databases can understand various numeric and character types of data, additional functionality needs to be added for databases to process spatial data types. Select Only Date Part From DateTime – Best Practice A very common question which I receive is how to only get Date or Time part from datetime value. In this blog post I explain the same in very simple words. T-SQL Paging Query Technique Comparison (OVER and ROW_NUMBER()) – CTE vs. Derived Table I have received few emails and comments about my post SQL SERVER – T-SQL Paging Query Technique Comparison – SQL 2000 vs SQL 2005. The main question was is this can be done using CTE? Absolutely! What about Performance? It is identical! Please refer above mentioned article for the history of paging. SQL SERVER – Cannot resolve collation conflict for equal to operation One of the very first error I ever encountered in my career was to resolve this conflict. I have blogged about it and I have realized that many others like me who are facing this error. LEN and DATALENGTH of NULL Simple Example Here is the question for you what is the LEN of NULL value? Well it is very easy – just read the blog. Recovery Models and Selection Very simple and easy explanation of the Database Backup Recovery Model and how to select the best option for you. Explanation SQL SERVER Hash Join Hash join gives best performance when two more join tables are joined and at-least one of them have no index or is not sorted. It is also expected that smaller of the either of table can be read in memory completely (though not necessary). Easy Sequence of SELECT FROM JOIN WHERE GROUP BY HAVING ORDER BY SELECT yourcolumns FROM tablenames JOIN tablenames WHERE condition GROUP BY yourcolumns HAVING aggregatecolumn condition ORDER BY yourcolumns NorthWind Database or AdventureWorks Database – Samples Databases In this blog post we learn how to install Northwind database. I also shared the source where one can download this database as that is used in many examples on MSDN help files. sp_HelpText for sp_HelpText – Puzzle A simple quick puzzle – do you know the answer of it? If not, go ahead and read the blog. 2008 SQL SERVER – 2008 – Step By Step Installation Guide With Images When SQL Server 2008 was newly introduced lots of people had no clue how to install SQL Server 2008 and the amount of the question which I used to receive were so much. I wrote this blog post with the spirit that this will help all the newbies to install SQL Server 2008 with the help of images. Still today this blog post has been bible for all of the people who are confused with SQL Server installation. Inline Variable Assignment I loved this feature. I have always wanted this feature to be present in SQL Server. The last time when I met developers from Microsoft SQL Server, I had talked about this feature. I think this feature saves some time but make the code more readable. Introduction to Policy Management – Enforcing Rules on SQL Server If our company policy is to create all the Stored Procedure with prefix ‘usp’ that developers should be just prevented to create Stored Procedure with any other prefix. Let us see a small tutorial how to create conditions and policy which will prevent any future SP to be created with any other prefix. 2009 Performance Counters from System Views – By Kevin Mckenna Many of you are not aware of this fact that access to performance information is readily available in SQL Server and that too without querying performance counters using a custom application or via perfmon. Till now, this fact has remained undisclosed but through this post I would like to explain you can easily access SQL Server performance counter information. Without putting much effort you will come across the system viewsys.dm_os_performance_counters. As the name suggests, this provides you easy access to the SQL Server performance counter information that is passed on to perfmon, but you can get at it via tsql. Customize Toolbar – Remove Debug Button from Toolbar I was fond of SQL Server Debugger feature in SQL Server 2000. To my utter disappointment, this feature was withdrawn from SQL Server 2005. The button of the debugger is similar to a play button and is used to run debugging commands of Visual Studio. Because of this reason, it gets very much infuriating for developers when they are developing on both – Visual Studio and SSMS. Let us now see how we can remove debugging button from SQL Server Management Studio. Effect of Normalization on Index and Performance A very interesting conversation which started from twitter. If you want to read one link this is the link I encourage you to read it. SSMS Feature – Multi-server Queries Using SQL Server Management Studio (SSMS) DBAs can now query multiple servers from one window. It is quite common for DBAs with large amount of servers to maintain and gather information from multiple SQL Servers and create report. This feature is a blessing for the DBAs, as they can now assemble all the information instantaneously without going anywhere. Query Optimizer Hint ROBUST PLAN – Question to You “ROBUST PLAN” is a kind of query hint which works quite differently than other hints. It does not improve join or force any indexes to use; it just makes sure that a query does not crash due to over the limit size of row. Let me elaborate upon it in the blog post. 2010 Do you really know the difference between various date functions available in SQL Server 2012? Here is a three part story where we explored the same with examples: Fastest Way to Restore the Database Difference Between DATETIME and DATETIME2 Difference Between DATETIME and DATETIME2 – WITH GETDATE Shrinking NDF and MDF Files – Readers’ Opinion Shrinking Database always creates performance degradation and increases fragmentation in the database. I suggest that you keep that in mind before you start reading the following comment. If you are going to say Shrinking Database is bad and evil, here I am saying it first and loud. Now, the comment of Imran is written while keeping in mind only the process showing how the Shrinking Database Operation works. Imran has already explained his understanding and requests further explanation. I have removed the Best Practices section from Imran’s comments, as there are a few corrections. 2011 Solution – Puzzle – SELECT * vs SELECT COUNT(*) This is very interesting question and I am very confident that not every one knows the answer to this question. Let me ask you again – Which will be faster SELECT* or SELECT COUNT (*) or do you think this is apples and oranges comparison. 2012 Service Broker and CAP_CPU_PERCENT – Limiting SQL Server Instances to CPU Usage In SQL Server 2012 there are a few enhancements with regards to SQL Server Resource Governor. One of the enhancement is how the resources are allocated. Let me explain you with examples. Let us understand the entire discussion with the help of three different examples. Finding Size of a Columnstore Index Using DMVs One of the very common question I often see is need of the list of columnstore index along with their size and corresponding table name. I quickly re-wrote a script using DMVs sys.indexes and sys.dm_db_partition_stats. This script gives the size of the columnstore index on disk only. I am sure there will be advanced script to retrieve details related to components associated with the columnstore index. However, I believe following script is sufficient to start getting an idea of columnstore index size. Developer Training Resources and Summary Roundup Developer Training - Importance and Significance - Part 1 In this part we discussed the importance of training in the real world. The most important and valuable resource any company is its employee. Employees who have been well-trained will be better at their jobs and produce a better product.  An employee who is well trained obviously knows more about their job and all the technical aspects. I have a very high opinion about training employees and it is the most important task. Developer Training – Employee Morals and Ethics – Part 2 In this part we discussed the most crucial components of training. Often employees are expecting the company to pay for their training and the company expresses no interest in training the employee. Quite often training expenses are the real issue for both the employee and employer. Developer Training – Difficult Questions and Alternative Perspective - Part 3 This part was the most difficult to write as I tried to address a few difficult questions and answers. Training is such a sensitive issue that many developers when not receiving chance for training think about leaving the organization. Developer Training – Various Options for Developer Training – Part 4 In this part I tried to explore a few methods and options for training. The generic feedback I received on this blog post was short and I should have explored each of the subject of the training in details. I believe there are two big buckets of training 1) Instructor Lead Training and 2) Self Lead Training. Developer Training – A Conclusive Summary- Part 5 There is no better motivation than a personal desire to learn new technology. Honestly there is nothing more personal learning. That “change is the only constant” and “adapt & overcome” are the essential lessons of life. One cannot stop the learning and resist the change. In the IT industry “ego of knowing all” and the “resistance to change” are the most challenging issues. A Quick Look at Logging and Ideas around Logging Question: What is the first thing comes to your mind when you hear the word “Logging”? Strange enough I got a different answer every single time. Let me just list what answer I got from my friends. Let us go over them one by one. Beginning Performance Tuning with SQL Server Execution Plan Solution of Puzzle – Swap Value of Column Without Case Statement Earlier this week I asked a question where I asked how to Swap Values of the column without using CASE Statement. Read here: SQL SERVER – A Puzzle – Swap Value of Column Without Case Statement. I have proposed 3 different solutions in the blog posts itself. I had requested the help of the community to come up with alternate solutions and honestly I am stunned and amazed by the qualified entries. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • That Escalated Quickly

    - by Jesse Taber
    Originally posted on: http://geekswithblogs.net/GruffCode/archive/2014/05/17/that-escalated-quickly.aspxI have been working remotely out of my home for over 4 years now. All of my coworkers during that time have also worked remotely. Lots of folks have written about the challenges inherent in facilitating communication on remote teams and strategies for overcoming them. A popular theme around this topic is the notion of “escalating communication”. In this context “escalating” means taking a conversation from one mode of communication to a different, higher fidelity mode of communication. Here are the five modes of communication I use at work in order of increasing fidelity: Email – This is the “lowest fidelity” mode of communication that I use. I usually only check it a few times a day (and I’m trying to check it even less frequently than that) and I only keep items in my inbox if they represent an item I need to take action on that I haven’t tracked anywhere else. Forums / Message boards – Being a developer, I’ve gotten into the habit of having other people look over my code before it becomes part of the product I’m working on. These code reviews often happen in “real time” via screen sharing, but I also always have someone else give all of the changes another look using pull requests. A pull request takes my code and lets someone else see the changes I’ve made side-by-side with the existing code so they can see if I did anything dumb. Pull requests can facilitate a conversation about the code changes in an online-forum like style. Some teams I’ve worked on also liked using tools like Trello or Google Groups to have on-going conversations about a topic or task that was being worked on. Chat & Instant Messaging  - Chat and instant messaging are the real workhorses for communication on the remote teams I’ve been a part of. I know some teams that are co-located that also use it pretty extensively for quick messages that don’t warrant walking across the office to talk with someone but reqire more immediacy than an e-mail. For the purposes of this post I think it’s important to note that the terms “chat” and “instant messaging” might insinuate that the conversation is happening in real time, but that’s not always true. Modern chat and IM applications maintain a searchable history so people can easily see what might have been discussed while they were away from their computers. Voice, Video and Screen sharing – Everyone’s got a camera and microphone on their computers now, and there are an abundance of services that will let you use them to talk to other people who have cameras and microphones on their computers. I’m including screen sharing here as well because, in my experience, these discussions typically involve one or more people showing the other participants something that’s happening on their screen. Obviously, this mode of communication is much higher-fidelity than any of the ones listed above. Scheduled meetings are typically conducted using this mode of communication. In Person – No matter how great communication tools become, there’s no substitute for meeting with someone face-to-face. However, opportunities for this kind of communcation are few and far between when you work on a remote team. When a conversation gets escalated that usually means it moves up one or more positions on this list. A lot of people advocate jumping to #4 sooner than later. Like them, I used to believe that, if it was possible, organizing a call with voice and video was automatically better than any kind of text-based communication could be. Lately, however, I’m becoming less convinced that escalating is always the right move. Working Asynchronously Last year I attended a talk at our local code camp given by Drew Miller. Drew works at GitHub and was talking about how they use GitHub internally. Many of the folks at GitHub work remotely, so communication was one of the main themes in Drew’s talk. During the talk Drew used the phrase, “asynchronous communication” to describe their use of chat and pull request comments. That phrase stuck in my head because I hadn’t heard it before but I think it perfectly describes the way in which remote teams often need to communicate. You don’t always know when your co-workers are at their computers or what hours (if any) they are working that day. In order to work this way you need to assume that the person you’re talking to might not respond right away. You can’t always afford to wait until everyone required is online and available to join a voice call, so you need to use text-based, persistent forms of communication so that people can receive and respond to messages when they are available. Going back to my list from the beginning of this post for a second, I characterize items #1-3 as being “asynchronous” modes of communication while we could call items #4 and #5 “synchronous”. When communication gets escalated it’s almost always moving from an asynchronous mode of communication to a synchronous one. Now, to the point of this post: I’ve become increasingly reluctant to escalate from asynchronous to synchronous communication for two primary reasons: 1 – You can often find a higher fidelity way to convey your message without holding a synchronous conversation 2 - Asynchronous modes of communication are (usually) persistent and searchable. You Don’t Have to Broadcast Live Let’s start with the first reason I’ve listed. A lot of times you feel like you need to escalate to synchronous communication because you’re having difficulty describing something that you’re seeing in words. You want to provide the people you’re conversing with some audio-visual aids to help them understand the point that you’re trying to make and you think that getting on Skype and sharing your screen with them is the best way to do that. Firing up a screen sharing session does work well, but you can usually accomplish the same thing in an asynchronous manner. For example, you could take a screenshot and annotate it with some text and drawings to illustrate what it is you’re seeing. If a screenshot won’t work, taking a short screen recording while your narrate over it and posting the video to your forum or chat system along with a text-based description of what’s in the recording that can be searched for later can be a great way to effectively communicate with your team asynchronously. I Said What?!? Now for the second reason I listed: most asynchronous modes of communication provide a transcript of what was said and what decisions might have been made during the conversation. There have been many occasions where I’ve used the search feature of my team’s chat application to find a conversation that happened several weeks or months ago to remember what was decided. Unfortunately, I think the benefits associated with the persistence of communicating asynchronously often get overlooked when people decide to escalate to a in-person meeting or voice/video call. I’m becoming much more reluctant to suggest a voice or video call if I suspect that it might lead to codifying some kind of design decision because everyone involved is going to hang up the call and immediately forget what was decided. I recognize that you can record and archive these types of interactions, but without being able to search them the recordings aren’t terribly useful. When and How To Escalate I don’t mean to imply that communicating via voice/video or in person is never a good idea. I probably jump on a Skype call with a co-worker at least once a day to quickly hash something out or show them a bit of code that I’m working on. Also, meeting in person periodically is really important for remote teams. There’s no way around the fact that sometimes it’s easier to jump on a call and show someone my screen so they can see what I’m seeing. So when is it right to escalate? I think the simplest way to answer that is when the communication starts to feel painful. Everyone’s tolerance for that pain is different, but I think you need to let it hurt a little bit before jumping to synchronous communication. When you do escalate from asynchronous to synchronous communication, there are a couple of things you can do to maximize the effectiveness of the communication: Takes notes – This is huge and yet I’ve found that a lot of teams don’t do this. If you’re holding a meeting with  > 2 people you should have someone taking notes. Taking notes while participating in a meeting can be difficult but there are a few strategies to deal with this challenge that probably deserve a short post of their own. After the meeting, make sure the notes are posted to a place where all concerned parties (including those that might not have attended the meeting) can review and search them. Persist decisions made ASAP – If any decisions were made during the meeting, persist those decisions to a searchable medium as soon as possible following the conversation. All the teams I’ve worked on used a web-based system for tracking the on-going work and a backlog of work to be done in the future. I always try to make sure that all of the cards/stories/tasks/whatever in these systems always reflect the latest decisions that were made as the work was being planned and executed. If held a quick call with your team lead and decided that it wasn’t worth the effort to build real-time validation into that new UI you were working on, go and codify that decision in the story associated with that work immediately after you hang up. Even better, write it up in the story while you are both still on the phone. That way when the folks from your QA team pick up the story to test a few days later they’ll know why the real-time validation isn’t there without having to invoke yet another conversation about the work. Communicating Well is Hard At this point you might be thinking that communicating asynchronously is more difficult than having a live conversation. You’re right: it is more difficult. In order to communicate effectively this way you need to very carefully think about the message that you’re trying to convey and craft it in a way that’s easy for your audience to understand. This is almost always harder than just talking through a problem in real time with someone; this is why escalating communication is such a popular idea. Why wouldn’t we want to do the thing that’s easier? Easier isn’t always better. If you and your team can get in the habit of communicating effectively in an asynchronous manner you’ll find that, over time, all of your communications get less painful because you don’t need to re-iterate previously made points over and over again. If you communicate right the first time, you often don’t need to rehash old conversations because you can go back and find the decisions that were made laid out in plain language. You’ll also find that you get better at doing things like writing useful comments in your code, creating written documentation about how the feature that you just built works, or persuading your team to do things in a certain way.

    Read the article

  • SQL SERVER – Weekly Series – Memory Lane – #007

    - by pinaldave
    Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2006 Find Stored Procedure Related to Table in Database – Search in All Stored Procedure In 2006 I wrote a small script which will help user  find all the Stored Procedures (SP) which are related to one or more specific tables. This was quite a popular script however, in SQL Server 2012 the same can be achieved using new DMV sys.sql-expression_dependencies. I recently blogged about it over Find Referenced or Referencing Object in SQL Server using sys.sql_expression_dependencies. 2007 SQL SERVER – Versions, CodeNames, Year of Release 1993 – SQL Server 4.21 for Windows NT 1995 – SQL Server 6.0, codenamed SQL95 1996 – SQL Server 6.5, codenamed Hydra 1999 – SQL Server 7.0, codenamed Sphinx 1999 – SQL Server 7.0 OLAP, codenamed Plato 2000 – SQL Server 2000 32-bit, codenamed Shiloh (version 8.0) 2003 – SQL Server 2000 64-bit, codenamed Liberty 2005 – SQL Server 2005, codenamed Yukon (version 9.0) 2008 – SQL Server 2008, codenamed Katmai (version 10.0) 2011 – SQL Server 2008, codenamed Denali (version 11.0) Search String in Stored Procedure Searching sting in the stored procedure is one of the most frequent task developer do. They might be searching for a table, view or any other details. I have written a script to do the same in SQL Server 2000 and SQL Server 2005. This is worth bookmarking blog post. There is an alternative way to do the same as well here is the example. 2008 SQL SERVER – Refresh Database Using T-SQL NO! Some of the questions have a single answer NO! You may want to read the question in the original blog post. I had a great time saying No! SQL SERVER – Delete Backup History – Cleanup Backup History SQL Server stores history of all the taken backup forever. History of all the backup is stored in the msdb database. Many times older history is no more required. Following Stored Procedure can be executed with a parameter which takes days of history to keep. In the following example 30 is passed to keep a history of month. 2009 Stored Procedure are Compiled on First Run – SP taking Longer to Run First Time Is stored procedure pre-compiled? Why the Stored Procedure takes a long time to run for the first time?  This is a very common questions often discussed by developers and DBAs. There is an absolutely definite answer but the question has been discussed forever. There is a misconception that stored procedures are pre-compiled. They are not pre-compiled, but compiled only during the first run. For every subsequent runs, it is for sure pre-compiled. Read the entire article for example and demonstration. Removing Key Lookup – Seek Predicate – Predicate – An Interesting Observation Related to Datatypes This is one of the most important performance tuning lesson on my blog. I suggest this weekend you spend time reading them and let me know what you think about the concepts which I have demonstrated in the four part series. Part 1 | Part 2 | Part 3 | Part 4 Seek Predicate is the operation that describes the b-tree portion of the Seek. Predicate is the operation that describes the additional filter using non-key columns. Based on the description, it is very clear that Seek Predicate is better than Predicate as it searches indexes whereas in Predicate, the search is on non-key columns – which implies that the search is on the data in page files itself. Policy Based Management – Create, Evaluate and Fix Policies This article will cover the most spectacular feature of SQL Server – Policy-based management and how the configuration of SQL Server with policy-based management architecture can make a powerful difference. Policy based management is loaded with several advantages. It can help you implement various policies for reliable configuration of the system. It also provides additional administration assistance to DBAs and helps them effortlessly manage various tasks of SQL Server across the enterprise. 2010 Recycle Error Log – Create New Log file without Server Restart Once I observed a DBA to restaring the SQL Server when he needed new error log file. This was funny and sad both at the same time. There is no need to restart the server to create a new log file or recycle the log file. You can run sp_cycle_errorlog and achieve the same result. Get Database Backup History for a Single Database Simple but effective script! Reducing CXPACKET Wait Stats for High Transactional Database The subject is very complex and I have done my best to simplify the concept. In simpler words, when a parallel operation is created for SQL Query, there are multiple threads for a single query. Each query deals with a different set of the data (or rows). Due to some reasons, one or more of the threads lag behind, creating the CXPACKET Wait Stat. Threads which came first have to wait for the slower thread to finish. The Wait by a specific completed thread is called CXPACKET Wait Stat. Information Related to DATETIME and DATETIME2 There are quite a lot of confusion with DATETIME and DATETIME2. DATETIME2 is also one of the underutilized datatype of SQL Server.  In this blog post I have written a follow up of the my earlier datetime series where I clarify a few of the concepts related to datetime. Difference Between GETDATE and SYSDATETIME Difference Between DATETIME and DATETIME2 – WITH GETDATE Difference Between DATETIME and DATETIME2 2011 Introduction to CUME_DIST – Analytic Functions Introduced in SQL Server 2012 SQL Server 2012 introduces new analytical function CUME_DIST(). This function provides cumulative distribution value. It will be very difficult to explain this in words so I will attempt small example to explain you this function. Instead of creating new table, I will be using AdventureWorks sample database as most of the developer uses that for experiment. Introduction to FIRST _VALUE and LAST_VALUE – Analytic Functions Introduced in SQL Server 2012 SQL Server 2012 introduces new analytical functions FIRST_VALUE() and LAST_VALUE(). This function returns first and last value from the list. It will be very difficult to explain this in words so I’d like to attempt to explain its function through a brief example. Instead of creating a new table, I will be using the AdventureWorks sample database as most developers use that for experiment purposes. OVER clause with FIRST _VALUE and LAST_VALUE – Analytic Functions Introduced in SQL Server 2012 – ROWS BETWEEN UNBOUNDED PRECEDING AND UNBOUNDED FOLLOWING “Don’t you think there is bug in your first example where FIRST_VALUE is remain same but the LAST_VALUE is changing every line. I think the LAST_VALUE should be the highest value in the windows or set of result.” Puzzle – Functions FIRST_VALUE and LAST_VALUE with OVER clause and ORDER BY You can see that row number 2, 3, 4, and 5 has same SalesOrderID = 43667. The FIRST_VALUE is 78 and LAST_VALUE is 77. Now if these function was working on maximum and minimum value they should have given answer as 77 and 80 respectively instead of 78 and 77. Also the value of FIRST_VALUE is greater than LAST_VALUE 77. Why? Explain in detail. Introduction to LEAD and LAG – Analytic Functions Introduced in SQL Server 2012 SQL Server 2012 introduces new analytical function LEAD() and LAG(). This functions accesses data from a subsequent row (for lead) and previous row (for lag) in the same result set without the use of a self-join . It will be very difficult to explain this in words so I will attempt small example to explain you this function. Instead of creating new table, I will be using AdventureWorks sample database as most of the developer uses that for experiment. A Real Story of Book Getting ‘Out of Stock’ to A 25% Discount Story Available Our book was out of stock in 48 hours of it was arrived in stock! We got call from the online store with a request for more copies within 12 hours. But we had printed only as many as we had sent them. There were no extra copies. We finally talked to the printer to get more copies. However, due to festivals and holidays the copies could not be shipped to the online retailer for two days. We knew for sure that they were going to be out of the book for 48 hours. This is the story of how we overcame that situation! Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • SQL SERVER – Auto Complete and Format T-SQL Code – Devart SQL Complete

    - by pinaldave
    Some people call it laziness, some will call it efficiency, some think it is the right thing to do. At any rate, tools are meant to make a job easier, and I like to use various tools. If we consider the history of the world, if we all wanted to keep traditional practices, we would have never invented the wheel.  But as time progressed, people wanted convenience and efficiency, which then led to laziness. Wanting a more efficient way to do something is not inherently lazy.  That’s how I see any efficiency tools. A few days ago I found Devart SQL Complete.  It took less than a minute to install, and after installation it just worked without needing any tweaking.  Once I started using it I was impressed with how fast it formats SQL code – you can write down any terms or even copy and paste.  You can start typing right away, and it will complete keywords, object names, and fragmentations. It completes statement expressions.  How many times do we write insert, update, delete?  Take this example: to alter a stored procedure name, we don’t remember the code written in it, you have to write it over again, or go back to SQL Server Studio Manager to create and alter which is very difficult.  With SQL Complete , you can write “alter stored procedure,” and it will finish it for you, and you can modify as needed. I love to write code, and I love well-written code.  When I am working with clients, and I find people whose code have not been written properly, I feel a little uncomfortable.  It is difficult to deal with code that is in the wrong case, with no line breaks, no white spaces, improper indents, and no text wrapping.  The worst thing to encounter is code that goes all the way to the right side, and you have to scroll a million times because there are no breaks or indents.  SQL Complete will take care of this for you – if a developer is too lazy for proper formatting, then Devart’s SQL formatter tool will make them better, not lazier. SQL Management Studio gives information about your code when you hover your mouse over it, however SQL Complete goes further in it, going into the work table, and the current rate idea, too. It gives you more information about the parameters; and last but not least, it will just take you to the help file of code navigation.  It will open object explorer in a document viewer.  You can start going through the various properties of your code – a very important thing to do. Here are are interesting Intellisense examples: 1) We are often very lazy to expand *however, when we are using SQL Complete we can just mouse over the * and it will give us all the the column names and we can select the appropriate columns. 2) We can put the cursor after * and it will give us option to expand it to all the column names by pressing the Tab key. 3) Here is one more Intellisense feature I really liked it. I always alias my tables and I always select the alias with special logic. When I was using SQL Complete I selected just a tablename (without schema name) and…(just like below image) … and it autocompleted the schema and alias name (the way I needed it). I believe using SQL Complete we can work faster.  It supports all versions of SQL Server, and works SQL formatting.  Many businesses perform code review and have code standards, so why not use an efficiency tool on everyone’s computer and make sure the code is written correctly from the first time?  If you’re interested in this tool, there are free editions available.  If you like it, you can buy it.  I bought it because it works.  I love it, and I want to hear all your opinions on it, too. You can get the product for FREE.  Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Utility, T SQL, Technology

    Read the article

  • Your Job Search Should be More Than Just a New Year's Resolution

    - by david.talamelli
    I love the beginning of a new year, it is a great chance to refocus and either re-evaluate goals you are working to or even set new ones. I don't have any statistics to measure this but I am sure that one of the more popular new year's resolutions in the general workforce is to either get a new job or work to further develop one's career. I think this is a good idea, in today's competitive work force people should have a plan of what they want to do, what role they are after and how to get there. One common mistake I think many people make though is that a career plan shouldn't be a once a year thought. When people finish with the holiday season with their new year's resolution to find a new job fresh in their mind, you can see the enthusiasm and motivation a person has to make something happen. Emails are sent, calls are made, applications are made, networking is happening, etc..... Finding the right role that you are after however can be difficult, while it would be great if that dream role was available just at the time you happened to be looking for it - in reality this is not always the case. Job Seekers need to keep reminding themselves that while sometimes that dream job they are after is available at the same time they are looking, that also a Job search can be a difficult and long process. Many people who set out with the best of intentions in January to find a new job can soon lose interest in a job search if they do not immediately find a role. Just like the Christmas decorations are put away and the photos from New Year's are stored away - a Job Seeker's motivation may slowly decrease until that person finds themselves 12 months later in the same situation in same role and looking for that new opportunity again. Rather than just "going for it" and looking for a role in the month of January, a person's job search or career plan should be an ongoing activity and thought process that is constantly updated and evaluated over the course of the year. It can be hard to stay motivated over an extended period of time, especially when you are newly motivated and ready for that new role and the results are not immediate. Rather than letting your job search fall down the priority list and into the "too hard basket" a few ideas that may keep your enthusiasm fresh Update your resume every 6 months, even if you are not looking for a job - it is easy to forget what you have accomplished if you don't keep your details updated. Also it is good to be prepared and have a resume ready to go in case you do get an unexpected phone call for that 'dream job' you have been hoping for. Work out what you want out of your next role before you begin your job search - rather than aimlessly searching job ads or talking to people - think of the organisations or type of role you would like before you search. If you know what you are looking for it will be much easier to work out how to get there than if you do not know what you want. Don't expect immediate results once you decide to look for another job, things don't always fall into place. Timing and delivery can be important pieces of being selected for a role, companies don't hire every role in January. Have an open mind - people you meet or talk to may not result in immediate results for your job search but every connection may help you get a bit closer to what you are after . These actions will not guarantee a positive result, but in today's competitive work force every little of extra preparation and planning helps. All the best for 2011 and I hope your career plan whatever it may be is a success.

    Read the article

  • SQL SERVER – Shard No More – An Innovative Look at Distributed Peer-to-peer SQL Database

    - by pinaldave
    There is no doubt that SQL databases play an important role in modern applications. In an ideal world, a single database can handle hundreds of incoming connections from multiple clients and scale to accommodate the related transactions. However the world is not ideal and databases are often a cause of major headaches when applications need to scale to accommodate more connections, transactions, or both. In order to overcome scaling issues, application developers often resort to administrative acrobatics, also known as database sharding. Sharding helps to improve application performance and throughput by splitting the database into two or more shards. Unfortunately, this practice also requires application developers to code transactional consistency into their applications. Getting transactional consistency across multiple SQL database shards can prove to be very difficult. Sharding requires developers to think about things like rollbacks, constraints, and referential integrity across tables within their applications when these types of concerns are best handled by the database. It also makes other common operations such as joins, searches, and memory management very difficult. In short, the very solution implemented to overcome throughput issues becomes a bottleneck in and of itself. What if database sharding was no longer required to scale your application? Let me explain. For the past several months I have been following and writing about NuoDB, a hot new SQL database technology out of Cambridge, MA. NuoDB is officially out of beta and they have recently released their first release candidate so I decided to dig into the database in a little more detail. Their architecture is very interesting and exciting because it completely eliminates the need to shard a database to achieve higher throughput. Each NuoDB database consists of at least three or more processes that enable a single database to run across multiple hosts. These processes include a Broker, a Transaction Engine and a Storage Manager.  Brokers are responsible for connecting client applications to Transaction Engines and maintain a global view of the network to keep track of the multiple Transaction Engines available at any time. Transaction Engines are in-memory processes that client applications connect to for processing SQL transactions. Storage Managers are responsible for persisting data to disk and serving up records to the Transaction Managers if they don’t exist in memory. The secret to NuoDB’s approach to solving the sharding problem is that it is a truly distributed, peer-to-peer, SQL database. Each of its processes can be deployed across multiple hosts. When client applications need to connect to a Transaction Engine, the Broker will automatically route the request to the most available process. Since multiple Transaction Engines and Storage Managers running across multiple host machines represent a single logical database, you never have to resort to sharding to get the throughput your application requires. NuoDB is a new pioneer in the SQL database world. They are making database scalability simple by eliminating the need for acrobatics such as sharding, and they are also making general administration of the database simpler as well.  Their distributed database appears to you as a user like a single SQL Server database.  With their RC1 release they have also provided a web based administrative console that they call NuoConsole. This tool makes it extremely easy to deploy and manage NuoDB processes across one or multiple hosts with the click of a mouse button. See for yourself by downloading NuoDB here. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: CodeProject, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology Tagged: NuoDB

    Read the article

  • Production Access Denied! Who caused this rule anyways?

    - by Matt Watson
    One of the biggest challenges for most developers is getting access to production servers. In smaller dev teams of less than about 5 people everyone usually has access. Then you hire developer #6, he messes something up in production... and now nobody has access. That is how it always starts in small dev teams. I think just about every rule of life there is gets created this way. One person messes it up for the rest of us. Rules are then put in place to try and prevent it from happening again.Breaking the rules is in our nature. In this example it is for good cause and a necessity to support our applications and troubleshoot problems as they arise. So how do developers typically break the rules? Some create their own method to collect log files off servers so they can see them. Expensive log management programs can collect log files, but log files alone are not enough. Centralizing where important errors are logged to is common. Some lucky developers are given production server access by the IT operations team out of necessity. Wait. That's not fair to all developers and knowingly breaks the company rule!  When customers complain or the system is down, the rules go out the window. Commonly lead developers get production access because they are ultimately responsible for supporting the application and may be the only person who knows how to fix it. The problem with only giving lead developers production access is it doesn't scale from a support standpoint. Those key employees become the go to people to help solve application problems, but they also become a bottleneck. They end up spending up to half of their time every day helping resolve application defects, performance problems, or whatever the fire of the day is. This actually the last thing you want your lead developers doing. They should be working on something more strategic like major enhancements to the product. Having production access can actually be a curse if you are the guy stuck hunting down log files all day. Application defects are good tasks for junior developers. They can usually handle figuring out simple application problems. But nothing is worse than being a junior developer who can't figure out those problems and the back log of them grows and grows. Some of them require production server access to verify a deployment was done correctly, verify config settings, view log files, or maybe just restart an application. Since the junior developers don't have access, they end up bugging the developers who do have access or they track down a system admin to help. It can take hours or days to see server information that would take seconds or minutes if they had access of their own. It is very frustrating to the developer trying to solve the problem, the system admin being forced to help, and most importantly your customers who are not happy about the situation. This process is terribly inefficient. Production database access is also important for solving application problems, but presents a lot of risk if developers are given access. They could see data they shouldn't.  They could write queries on accident to update data, delete data, or merely select every record from every table and bring your database to its knees. Since most of the application we create are data driven, it can be very difficult to track down application bugs without access to the production databases.Besides it being against the rule, why don't all developers have access? Most of the time it comes down to security, change of control, lack of training, and other valid reasons. Developers have been known to tinker with different settings to try and solve a problem and in the process forget what they changed and made the problem worse. So it is a double edge sword. Don't give them access and fixing bugs is more difficult, or give them access and risk having more bugs or major outages being created!Matt WatsonFounder, CEOStackifyAgile Support for Agile Developers

    Read the article

  • Data breakpoints to find points where data gets broken

    - by raccoon_tim
    When working with a large code base, finding reasons for bizarre bugs can often be like finding a needle in a hay stack. Finding out why an object gets corrupted without no apparent reason can be quite daunting, especially when it seems to happen randomly and totally out of context. Scenario Take the following scenario as an example. You have defined the a class that contains an array of characters that is 256 characters long. You now implement a method for filling this buffer with a string passed as an argument. At this point you mistakenly expect the buffer to be 256 characters long. At some point you notice that you require another character buffer and you add that after the previous one in the class definition. You now figure that you don’t need the 256 characters that the first member can hold and you shorten that to 128 to conserve space. At this point you should start thinking that you also have to modify the method defined above to safeguard against buffer overflow. It so happens, however, that in this not so perfect world this does not cross your mind. Buffer overflow is one of the most frequent sources for errors in a piece of software and often one of the most difficult ones to detect, especially when data is read from an outside source. Many mass copy functions provided by the C run-time provide versions that have boundary checking (defined with the _s suffix) but they can not guard against hard coded buffer lengths that at some point get changed. Finding the bug Getting back to the scenario, you’re now wondering why does the second string get modified with data that makes no sense at all. Luckily, Visual Studio provides you with a tool to help you with finding just these kinds of errors. It’s called data breakpoints. To add a data breakpoint, you first run your application in debug mode or attach to it in the usual way, and then go to Debug, select New Breakpoint and New Data Breakpoint. In the popup that opens, you can type in the memory address and the amount of bytes you wish to monitor. You can also use an expression here, but it’s often difficult to come up with an expression for data in an object allocated on the heap when not in the context of a certain stack frame. There are a couple of things to note about data breakpoints, however. First of all, Visual Studio supports a maximum of four data breakpoints at any given time. Another important thing to notice is that some C run-time functions modify memory in kernel space which does not trigger the data breakpoint. For instance, calling ReadFile on a buffer that is monitored by a data breakpoint will not trigger the breakpoint. The application will now break at the address you specified it to. Often you might immediately spot the issue but the very least this feature can do is point you in the right direction in search for the real reason why the memory gets inadvertently modified. Conclusions Data breakpoints are a great feature, especially when doing a lot of low level operations where multiple locations modify the same data. With the exception of some special cases, like kernel memory modification, you can use it whenever you need to check when memory at a certain location gets changed on purpose or inadvertently.

    Read the article

  • Too complex/too many objects?

    - by Mike Fairhurst
    I know that this will be a difficult question to answer without context, but hopefully there are at least some good guidelines to share on this. The questions are at the bottom if you want to skip the details. Most are about OOP in general. Begin context. I am a jr dev on a PHP application, and in general the devs I work with consider themselves to use many more OO concepts than most PHP devs. Still, in my research on clean code I have read about so many ways of using OO features to make code flexible, powerful, expressive, testable, etc. that is just plain not in use here. The current strongly OO API that I've proposed is being called too complex, even though it is trivial to implement. The problem I'm solving is that our permission checks are done via a message object (my API, they wanted to use arrays of constants) and the message object does not hold the validation object accountable for checking all provided data. Metaphorically, if your perm containing 'allowable' and 'rare but disallowed' is sent into a validator, the validator may not know to look for 'rare but disallowed', but approve 'allowable', which will actually approve the whole perm check. We have like 11 validators, too many to easily track at such minute detail. So I proposed an AtomicPermission class. To fix the previous example, the perm would instead contain two atomic permissions, one wrapping 'allowable' and the other wrapping 'rare but disallowed'. Where previously the validator would say 'the check is OK because it contains allowable,' now it would instead say '"allowable" is ok', at which point the check ends...and the check fails, because 'rare but disallowed' was not specifically okay-ed. The implementation is just 4 trivial objects, and rewriting a 10 line function into a 15 line function. abstract class PermissionAtom { public function allow(); // maybe deny() as well public function wasAllowed(); } class PermissionField extends PermissionAtom { public function getName(); public function getValue(); } class PermissionIdentifier extends PermissionAtom { public function getIdentifier(); } class PermissionAction extends PermissionAtom { public function getType(); } They say that this is 'not going to get us anything important' and it is 'too complex' and 'will be difficult for new developers to pick up.' I respectfully disagree, and there I end my context to begin the broader questions. So the question is about my OOP, are there any guidelines I should know: is this too complicated/too much OOP? Not that I expect to get more than 'it depends, I'd have to see if...' when is OO abstraction too much? when is OO abstraction too little? how can I determine when I am overthinking a problem vs fixing one? how can I determine when I am adding bad code to a bad project? how can I pitch these APIs? I feel the other devs would just rather say 'its too complicated' than ask 'can you explain it?' whenever I suggest a new class.

    Read the article

  • Best way to load application settings

    - by enzom83
    A simple way to keep the settings of a Java application is represented by a text file with ".properties" extension containing the identifier of each setting associated with a specific value (this value may be a number, string, date, etc..). C# uses a similar approach, but the text file must be named "App.config". In both cases, in source code you must initialize a specific class for reading settings: this class has a method that returns the value (as string) associated with the specified setting identifier. // Java example Properties config = new Properties(); config.load(...); String valueStr = config.getProperty("listening-port"); // ... // C# example NameValueCollection setting = ConfigurationManager.AppSettings; string valueStr = setting["listening-port"]; // ... In both cases we should parse strings loaded from the configuration file and assign the ??converted values to the related typed objects (parsing errors could occur during this phase). After the parsing step, we must check that the setting values ??belong to a specific domain of validity: for example, the maximum size of a queue should be a positive value, some values ??may be related (example: min < max), and so on. Suppose that the application should load the settings as soon as it starts: in other words, the first operation performed by the application is to load the settings. Any invalid values for the settings ??must be replaced automatically with default values??: if this happens to a group of related settings, those settings are all set with default values. The easiest way to perform these operations is to create a method that first parses all the settings, then checks the loaded values ??and finally sets any default values??. However maintenance is difficult if you use this approach: as the number of settings increases while developing the application, it becomes increasingly difficult to update the code. In order to solve this problem, I had thought of using the Template Method pattern, as follows. public abstract class Setting { protected abstract bool TryParseValues(); protected abstract bool CheckValues(); public abstract void SetDefaultValues(); /// <summary> /// Template Method /// </summary> public bool TrySetValuesOrDefault() { if (!TryParseValues() || !CheckValues()) { // parsing error or domain error SetDefaultValues(); return false; } return true; } } public class RangeSetting : Setting { private string minStr, maxStr; private byte min, max; public RangeSetting(string minStr, maxStr) { this.minStr = minStr; this.maxStr = maxStr; } protected override bool TryParseValues() { return (byte.TryParse(minStr, out min) && byte.TryParse(maxStr, out max)); } protected override bool CheckValues() { return (0 < min && min < max); } public override void SetDefaultValues() { min = 5; max = 10; } } The problem is that in this way we need to create a new class for each setting, even for a single value. Are there other solutions to this kind of problem? In summary: Easy maintenance: for example, the addition of one or more parameters. Extensibility: a first version of the application could read a single configuration file, but later versions may give the possibility of a multi-user setup (admin sets up a basic configuration, users can set only certain settings, etc..). Object oriented design.

    Read the article

  • Is HttpContextWrapper all that....useful?

    - by bakasan
    I've been going through the process of cleaning up our controller code to make each action as testable. Generally speaking, this hasn't been too difficult--where we have opportunity to use a fixed object, like say FormsAuthentication, we generally introduce some form of wrapper as appropriate and be on our merry way. For reasons not particularly germaine to this conversation, when it came to dealing with usage of HttpContext, we decided to use the newly created HttpContextWrapper class rather than inventing something homegrown. One thing we did introduce was the ability to swap in a HttpContextWrapper (like say, for unit testing). This was wholly inspired by the way Oren Eini handles unit testing with DateTimes (see article, a pattern we also use) public static class FooHttpContext { public static Func<HttpContextWrapper> Current = () => new HttpContextWrapper(HttpContext.Current); public static void Reset() { Current = () => new HttpContextWrapper(HttpContext.Current); } } Nothing particularly fancy. And it works just fine in our controller code. The kicker came when we go to write unit tests. We're using Moq as our mocking framework, but alas var context = new Mock<HttpContextWrapper>() breaks since HttpContextWrapper doesn't have a parameterless ctor. And what does it take as a ctor parameter? A HttpContext object. So I find myself in a catch 22. I'm using the prescribed way to decouple HttpContext--but I can't mock a value in because the original HttpContext object was sealed and therefore difficult to test. I can map HttpContextBase, which both derive from--but that doesn't really get me what I'm after. Am I just missing the point somewhere with regard to HttpContextWrapper? I can find ways to work around the issue, but we are kind of fond of remaining consistent in decoupling using the Function delegate pattern--but it seems like we're not fully grokking intent of the wrapper.

    Read the article

  • bug with varargs and overloading?

    - by pstanton
    There seems to be a bug in the Java varargs implementation. Java can't distinguish the appropriate type when a method is overloaded with different types of vararg parameters. It gives me an error The method ... is ambiguous for the type ... Consider the following code: public class Test { public static void main(String[] args) throws Throwable { doit(new int[]{1, 2}); // <- no problem doit(new double[]{1.2, 2.2}); // <- no problem doit(1.2f, 2.2f); // <- no problem doit(1.2d, 2.2d); // <- no problem doit(1, 2); // <- The method doit(double[]) is ambiguous for the type Test } public static void doit(double... ds) { System.out.println("doubles"); } public static void doit(int... is) { System.out.println("ints"); } } the docs say: "Generally speaking, you should not overload a varargs method, or it will be difficult for programmers to figure out which overloading gets called." however they don't mention this error, and it's not the programmers that are finding it difficult, it's the compiler. thoughts?

    Read the article

  • Product Catalog Schema design

    - by FlySwat
    I'm building a proof of concept schema for a product catalog to possibly replace a very aging and crufty one we use. In our business, we sell both physical materials and services (one time and reoccurring charges). The current catalog schema has each distinct category broken out into individual tables, while this is nicely normalized and performs well, it is fairly difficult to extend. Adding a new attribute to a particular product involves changing the table schema and backpopulating old data. An idea I've been toying with has been something along the line of a base set of entity tables in 3rd normal form, these will contain the facts that are common among ALL products. Then, I'd like to build an Attribute-Entity-Value schema that allows each entity type to be extended in a flexible way using just data and no schema changes. Finally, I'd like to denormalize this data model into materialized views for each individual entity type. This views are what the application would access. We also have many tables that contain business rules and compatibility rules. These would join against the base entity tables instead of the views. My big concerns here are: Performance - Attribute-Entity-Value schemas are flexible, but typically perform poorly, should I be concerned? More Performance - Denormalizing using materialized views may have some risks, I'm not positive on this yet. Complexity - While this schema is flexible and maintainable using just data, I worry that the complexity of the design might make future schema changes difficult. For those who have designed product catalogs for large scale enterprises, am I going down the totally wrong path? Is there any good best practice schema design reading available for product catalogs?

    Read the article

  • SHLoadImageFile(L"\\Program Files\\TrainingApp\\background.png"); whats that L in the argument for?

    - by ashishsony
    Hi, ive been working on c++ on linux for the past 2 years,and switched to windows c++ programming recently. can anyone tell me what that L is there in the argument of the function: SHLoadImageFile(L"\\Program Files\\TrainingApp\\background.png"); and on viewing certain sample code in MSVS C++ i came across hundereds of typedefs like.. LPARAM// typedef LONG_PTR LPARAM... here LONG_PTR is again typedef as __w64 long WPARAM// typedef UINT_PTR WPARAM... so there is a lot of chained typedefs.. I never saw this much of typedef chaining on c++ programming on linux using gcc.. what i want to say is that it just creates more confusion in this way for windows application programming.. while ive seen application programming on linux using frameworks like Qt.. there such things are rarely used.. so is there specific purpose in typedefining again and again on MSVSC++?? for eg.. there are typdefs like typedef int BOOL; whats the use of this when normal bool is available already..?? there are hundred other cases ive come across where just to decide what data type to use becomes so difficult.. it becomes difficult to understand a pre written code in this fashion too.. Thanks.

    Read the article

  • Advice on improving programming skills, learning capabilities?

    - by anonymous-coward1234
    Hi all, After 2,5 years of professional Java programing, I still have problems that make my job difficult and, more importantly - more times that I would like to admit - not enjoyable. I would like to ask for advice by more experienced people on ways that would help me overcome them. These are the problems I have: I do not absorb new knowledge easily. Even when I understand something, after a couple of days I easily forget even basic stuff. Other co-workers, even with the same working experience, when reading new technologies put things easily into "context", and are able to compare in "real time| similar technologies they already have used. I always try to address all the issues to whatever I am doing at one go, which results in me trying to resolve too many problems at the same time, losing completely control. I find it difficult to make my mind on a single problem that I should address first, and even when I do, and find myself throwing away code that I wrote because I started addressing the wrong issue first. As far as architecture and data modeling is concerned, I have difficulty making decisions on what objects must be created, with what hierarchy, interfaces, abstraction etc. I imagine that - to a certain degree - these things come with experience. But after 2,5 years of Java programming, I would expect myself to have come much farther that I have come, both in terms of absorption and experience. Is there a way to improve my learning speed? Any books, methods, advice is welcome.

    Read the article

  • Testing fault tolerant code

    - by Robert
    I’m currently working on a server application were we have agreed to try and maintain a certain level of service. The level of service we want to guaranty is: if a request is accepted by the server and the server sends on an acknowledgement to the client we want to guaranty that the request will happen, even if the server crashes. As requests can be long running and the acknowledgement time needs be short we implement this by persisting the request, then sending an acknowledgement to the client, then carrying out the various actions to fulfill the request. As actions are carried out they too are persisted, so the server knows the state of a request on start up, and there’s also various reconciliation mechanisms with external systems to check the accuracy of our logs. This all seems to work fairly well, but we have difficult saying this with any conviction as we find it very difficult to test our fault tolerant code. So far we’ve come up with two strategies but neither is entirely satisfactory: Have an external process watch the server code and then try and kill it off at what the external process thinks is an appropriate point in the test Add code the application that will cause it to crash a certain know critical points My problem with the first strategy is the external process cannot know the exact state of the application, so we cannot be sure we’re hitting the most problematic points in the code. My problem with the second strategy, although it gives more control over were the fault takes, is I do not like have code to inject faults within my application, even with optional compilation etc. I fear it would be too easy to over look a fault injection point and have it slip into a production environment.

    Read the article

  • does anyone know of good delphi docking components?

    - by X-Ray
    we'd like to add movable panels to an application. presently we've used DevExpress docking library but have found them to be disappointingly quirky & difficult to work with. it also has some limitations that aren't so great. auto-hide, pinning, and moving of pages by drag-and-drop are all features we'd like to use. the built-in delphi docking doesn't seem to be full-featured enough to do the things we need (also see sample below). perhaps i should dig deeper into delphi's docking abilities...my initial impression is that they seem very toolbar-oriented rather than something i can drop a frame into. i'm not experienced at docking topics. my only experience has been with the DevExpress docking library where i needed to programmatically create & dock panels. is it my imagination or are DevExpress's products unduly difficult to use/learn? the DevExpress Ribbon Bar component compared to the d2009 Ribbon Bar was certainly a useful experience. i will migrate to the d2009 Ribbon Bar as soon as convenient to do so. it was refreshingly straight-forward to learn and use. a sharp contrast compared to the DevExpress equivalent. if it takes 4x as longer to make it using the DevExpress equivalent, it's time to change direction. what would you suggest in regard to the docking library? thank you for your suggestions/comments!

    Read the article

  • What is the best software design to use in this scenario

    - by domdefelice
    I need to generate HTML snippets using jQuery. The creation of those snippets depends on some data. The data is stored server-side, in session (where PHP is used). At the moment I achieved this - retrieving the data from the server via AJAX in form of JSON - and building the snippets via specific javascript functions that read those data The problem is that the complexity of the data is getting bigger and hence the serialization into JSON is getting even more difficult since I can't do it automatically. I can't do it automatically because some information are sensible so I generate a "stripped" version to send to the client. I know it is difficult to understand without any code to read, but I am hoping this is a common scenario and would be glad for any tip, suggestion or even design-pattern you can give me. Should I store both a complete and a stripped data on the server and then use some library to automatically generate the JSON from the stripped data? But this also means I have to get the two data synchronized. Or maybe I could move the logic server-side, this way avoiding sending the data. But this means sending javascript code (since I rely on jQuery). Maybe not a good idea. Feel free to ask me more details if this is not clear. Thank you for any help

    Read the article

  • Browser: Continue gif animation after escape is pressed

    - by cottsak
    Firefox (and other browsers i believe) stop gif animation when you click the Stop button or invoke it via the Escape key. I have a text input that on change makes ajax requests to update other elements. As part of this ajaxyness i have an animated gif to show feedback. I also trap the escape key press in this input so as to clear the text field for better UX. My problem is after the escape key is pressed once, none of the ajax gifs animate anymore until the page is refreshed. Does anyone know a workaround? Stuff i've tried: I tried the e.stopPropagation(); and e.cancelBubble = true; in the function handling the e.keyCode == 27 and that didn't seem to work. I suspect that this stops trigging more js events and the browser catches the escape irrespective of js activity. I have the gif showing/hiding via adding/removing a css class so it's difficult to apply the "change gif url to reset" workaround. I dont even know if this works anyway - didn't test it. But it seems difficult. If anyone knows that this works and knows of an easy way to apply the hack with background-image: url(../images/ajax-loader_dotcirclel13x13.gif); css then please let me know.

    Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >