Search Results

Search found 10207 results on 409 pages for 'ethernet switch'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 17/409 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

  • What's required to enable communication between two IP ranges located behind one switch?

    - by Eric3
    Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

    Read the article

  • Lagging digital tv over ethernet

    - by Steve
    I have a HD Home Run TV over ethernet device, which connects the aerial to my router, and from there the router connects to my PC over about 15m of 100Mbps ethernet cable. The TV output lags every second. It does not do so for a computer much closer to the router. It is odd to me that the network rate is around 7Mbps on a 100Mbps cable. I am not downloading or streaming anything else on the affected computer. Is this lag caused by the speed of the cable, the length of the cable, or interference on the cable? I am considering swapping the ethernet cable with shielded ethernet cable.

    Read the article

  • convert home phone wiring to Ethernet

    - by aaa
    can i convert phone wiring in walls to act as only Ethernet network cause the phone wiring is not in use and not connected to the phone company so there is no voltage in the wires i remove the wall plate and i find 6 wires blue,blue/white,green,green/white,orange,orange/white , and i know that Ethernet use 8 here is what i am thinking get Ethernet cable cut it in half and attach wires from wall to the first computer and the same with the other computer so if this is possible do i just attach wires in the same color and ignore brown wire or do i have to rearrange wires , and how much the speed will be thank you in advance

    Read the article

  • convert home phone wiring to Ethernet

    - by aaa
    can i convert phone wiring in walls to act as only Ethernet network cause the phone wiring is not in use and not connected to the phone company so there is no voltage in the wires i remove the wall plate and i find 6 wires blue,blue/white,green,green/white,orange,orange/white , and i know that Ethernet use 8 here is what i am thinking get Ethernet cable cut it in half and attach wires from wall to the first computer and the same with the other computer so if this is possible do i just attach wires in the same color and ignore brown wire or do i have to rearrange wires , and how much the speed will be thank you in advance

    Read the article

  • Have you considered switch from Windows to OS X?

    - by Oscar Reyes
    For several years I wanted to move from Windows to OSX. Mainly because back then Windows95/98/2000 were terrible options. Now I have finally put my hands on this. Just when Vista and Win7 seems to redeem all the mistakes from their predecessors. The most terrible rant is the lack of the following keys: PageUp, PageDown, Home, End, Supr Not having those made my first programming day terrible on OSX. I don't regret switching, but somehow I expected something else. So: Have you considered switch to mac? What has stopped you? What is holding you back? If you have switched already, are you willing to comeback? (Now I run XP/Vista/Ubuntu/OSX in the same machine, yeah!!)

    Read the article

  • Why do we have to use break in switch

    - by trejder
    Who decided, and basing on what concepts, that switch construction (in many languages) has to be, like it is? Why do we have to use break in each statement? Why do we have to write something like this: switch(a) { case 1: result = 'one'; break; case 2: result = 'two'; break; default: result = 'not determined'; break; } I've noticed this construction in PHP and JS, but there are probably many other languages that uses it. If switch is an alternative of if, why we can't use the same construction for switch, as for if? I.e.: switch(a) { case 1: { result = 'one'; } case 2: { result = 'two'; } default: { result = 'not determined'; } } It is said, that break prevents execution of a blocks following current one. But, does someone really run into situation, where there was any need for execution of current block and following ones? I didn't. For me, break is always there. In every block. In every code.

    Read the article

  • Can't install wireless driver or get ubuntu to recognize ethernet cable

    - by Catherine
    I'm brand new to Ubuntu and I'm tearing my hair out trying to figure out how to connect to the internet. When I try to activate the Broadcom STA wireless driver, it says "Sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log." So I try the steps detailed here http://ubuntuforums.org/showthread.php?t=1967515&highlight=jockey Problem is, I can't connect to the internet via ethernet cable either. I tested the cable with another laptop and it works just fine. I don't know what to do. Any help is greatly appreciated.

    Read the article

  • Making a language switch main menu button in Drupal

    - by Let_Me_Be
    I have a bilingual site in Drupal. The problem is that I hate the language switch block taking up so much space (sometimes the only thing in the sidebar is the language switch block). So what I would love to have is language switch menu item, that would point to the other language (other then the current one). Something like this: | Home | Projects | BlaBla | | Cesky | after swith: | Domu | Projekty | Blabla | | English | Is that possible without writing a whole new module?

    Read the article

  • The Switch Workshop, by Red Gate and Re-Wired Group

    Customers don’t just buy a product — they switch from something else. And customers don’t just leave a product — they switch to something else. It’s in these switching moments that the deepest customer insights can be found. On the 25th of July, a select group of 32 people will attend a unique, hands-on, full-day workshop at Red Gate to learn about “The Switch”. ‘Disturbing Development’Grant Fritchey & the DBA Team present the latest installment of the Top 5 hard-earned lessons of a DBA – read it now

    Read the article

  • Open Source or Low Cost Layer 7 ("Content") Switch?

    - by Rob
    I have several web servers that host a number of different applications and web sites. I want to make it easy to host apps or parts of web sites on different servers (e.g. example.com/foo might be on one physical server and example.com/bar might be on another). We do this Apache redirects right now, but that gets messy fast and in any case we have other problems we want to solve, such as throttling requests from individual clients, and reducing dependency on specific physical hosts. Is there an open source or low cost layer 7 switch that would be suitable for this sort of task? I was hoping to find something like a stripped down Linux VMware guest/appliance built for this purpose, but haven't seen anything suitable out there so far.

    Read the article

  • Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

    - by Donal
    I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

    Read the article

  • Unable to ping inside or outside network with default gateway 0.0.0.0

    - by agentroadkill
    I've been around here before and I could usually piece together everything to more or less get myself up and running, but this time I'm truly stumped. I'm trying to connect my new 14.04 install to a network, and I'm forced to be behind my college's router. Now I've tested the vary cable that is right now plugged into my Ubuntu box on a Windows, Mac OS X, and even my friend's Ubuntu 14.04 box, and they all connect no problem. I've been trying to track this down for about two days, but every time I get close to it, the bug jumps to some other piece of my connection. Anyway, as it sits ifconfig -a gives: eth2 Lninkencap:Ethernet HWaddr:00:1f:bc:08:31:1d inet addr:10.32.51.51 Bcast:10.32.51.155 Mask: 255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 RX bytes:0 TX bytes:0 as well as the local loopback, but I'm assuming that is not an issue here. sudo dhclient -v eth2 returns: Listening on LPF/<hardware address of my integrated NIC, above> Sending on <same> Sending on Socket/fallback DHCPREQUEST of 10.32.51.51 on eth2 to 255.255.255.255 port 67 (xid=0x6f4a66ba) <two more lines of same> DHCPDISCOVER on eth2 to 255.255.255.255 port 67 interval 3 (xid=0x156f9fb4) <many more of above with varying intervals> No DHCPOFFERS received. Trying recorded lease 10.32.51.51 RTNETLINK answers: File exists bound: renewal in <large number> seconds If I then try ping 8.8.8.8, I get: connect: Network is unreachable /etc/resolv.conf only contains the two lines telling you not to edit it, while /etc/network/interfaces only has the loopback interface block in it. I've tried commenting out the "option rfc3442" line in /etc/dhcp/dhclient.conf which seemed to fix this issue for many people, as well as adding the line send vendor-class-indentifier "MSFT5.0" to dhclient.conf as well to tell the router I'm a windows box, in case they don't like Linux. Finally, route -n reveals: Destination Gateway Genmask Flags Metric Ref Use Iface 10.32.51.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 I would like to apologize in advance for the doubtless butchered text alignment, but I'm obviously typing this all by hand, reading from the terminal as I type commands. I'm hoping this is an interesting problem, and not something I blithely stumbled past in my (apparent) over-confidence. TIA! Quick addendum before posting: The activity light on the ethernet port are lit and one blinks during boot, but they rarely (and seemingly randomly) do so afterwards (both are dark) even while running dhclient in the foreground. When I had the Ubuntu box tethered to my MacBook earlier, I got what looked like a normal power/uplink blinking pattern, but was unable to ping one from the other.

    Read the article

  • How to connect Ethernet on Ubuntu (with auto-detection)

    - by user12285
    It's been well over six months but I have the same router SmartAX MT880d with Ethernet, and the exact same problem : no internet, even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. I'm a total beginner with Ubuntu. My internet works great in Windows but does not work in Ubuntu. Sorry if I don't use the right (technical) terminology to explain my issue. English is not my mother tongue. For 2 weeks, I've been doing reading on the web and forums and the ubuntuguide.org to name a few, but to no avail. Now I see no other solution but to ask for help. My problem is that I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files. E.g.: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm concerned that I might put figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem? Is the subnet 255.255.255.0? Gateway 192.168.1.1? I'm confused as I can also see a different IP starting with 155131*** (is it an account number?) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • Sharing an internet connection through the Ethernet port

    - by Bob Cunningham
    I have a small living room PC (Bohica, running fully-updated Ubuntu 10.10/Maverick) connected to my HDTV that I use for web browsing and media streaming. It connects via WiFi (wlan0) to my Fedora server (Snafu) that in turn connects to the internet. I use static addressing, and everything has been working fine. I just got a Blu-ray player, and I'd like to give it wired network access to the internet via Bohica's available wired ethernet port (eth0). So far, I haven't been to get eth0 and the network configured to get the Blu-ray player talking to the internet. Here's my wlan0 configuration: ip4 addr: 192.168.0.100 mask: /24 (255.255.255.0) gateway: 192.168.0.4 (fedora box) The Blu-ray player is set to an IP of 192.168.0.98/24, with the same gateway as above. I want eth0 set to an IP of 192.168.0.99/24, but when I do this using nm-connection-editor I lose internet access (the system tries to use eth0 as the default internet access interface). How do I get my blu-ray player to talk to the internet through Bohica, and do so without disrupting my current (working) network? Thanks. Edit: Here's the relevant output from nm-tool with the Blu-ray player connected: $ nm-tool NetworkManager Tool State: connected - Device: eth0 Type: Wired Driver: forcedeth State: disconnected Default: no HW Address: 90:FB:A6:2C:94:32 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on - Device: wlan0 [wlan0] Type: 802.11 WiFi Driver: ndiswrapper State: connected Default: yes HW Address: 00:26:5A:C0:D0:05 IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.4

    Read the article

  • How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

    - by user12285
    Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • How do I install Intel ethernet drivers?

    - by Pat
    I just bought a Lenovo T420, I booted the live CD and couldn't connect to my wireless router so I figured I needed the drivers for it. I have the last version of Ubuntu(12.04). It's a Intel® 82579 Gigabit Ethernet Controller So I went on intel's website and downloaded the Drivers for Linux and compiled them with make install. Here's the tutorial I followed: Linux Driver Install I have a few question though, What are these doing : modprobe e1000e ifconfig eth0 up dhclient eth0 ping intel.com As far as what I've read, modprobe seems to add the driver to the list of drivers for the kernel, but is that operation only good for one session? The two other lines, I don't understand either what they are doing. What does he mean at the end when he mentions : Note: Whenever the kernel version is upgraded you will need rebuild this driver. And are these steps permanent? Or do I have to add them to some boot.conf file for everytime I boot. Anyways, the steps worked for me and I have established a connection with my router, I just need to know if I need to do additional steps to keep the driver permanently etc.

    Read the article

  • Intermittent wired network issues in 14.04

    - by Tommy Brunn
    Since yesterday, my wired network connection has been dropping for a couple of seconds every 30 seconds or so. To my knowledge, I had not made any changes to my network. Output of ifconfig -a: ? ~ ifconfig -a eth0 Link encap:Ethernet HWaddr 6c:f0:49:b9:b1:7f inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:feb9:b17f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11597 errors:0 dropped:0 overruns:0 frame:0 TX packets:9783 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10101682 (10.1 MB) TX bytes:1215142 (1.2 MB) Interrupt:48 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:96691 errors:0 dropped:0 overruns:0 frame:0 TX packets:96691 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13594355 (13.5 MB) TX bytes:13594355 (13.5 MB) lspci |grep Ethernet: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) Pinging my router: ? ~ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.435 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.571 ms ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable 64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=1.03 ms And the output of route: ? ~ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 1 0 0 eth0 Some messages from /var/logs/syslog: ? ~ tail -f /var/log/syslog Jun 6 10:37:34 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:34 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:37 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:37 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:39 lolbox dhclient: XMT: Solicit on eth0, interval 8660ms. Jun 6 10:37:39 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:39 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:47 lolbox dhclient: XMT: Solicit on eth0, interval 16820ms. Jun 6 10:37:47 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:47 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:04 lolbox dhclient: XMT: Solicit on eth0, interval 34410ms. Jun 6 10:38:04 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:04 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13045 Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:37:34 lolbox whoopsie[1133]: online Jun 6 10:38:16 lolbox whoopsie[1133]: offline Jun 6 10:38:16 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:38:16 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13044 Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:38:16 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:17 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:17 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:17 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:18 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13160 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13161 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:38:18 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:18 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:18 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:18 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:18 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:18 lolbox dhclient: All rights reserved. Jun 6 10:38:18 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:18 lolbox dhclient: Jun 6 10:38:19 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:19 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:19 lolbox dhclient: All rights reserved. Jun 6 10:38:19 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:19 lolbox dhclient: Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:38:19 lolbox dhclient: Bound to *:546 Jun 6 10:38:19 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:38:19 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv6 state changed nbi -> preinit6 Jun 6 10:38:19 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on Socket/fallback Jun 6 10:38:19 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3fc9376d) Jun 6 10:38:19 lolbox dhclient: XMT: Solicit on eth0, interval 1020ms. Jun 6 10:38:19 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:19 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:38:20 lolbox dhclient: bound to 192.168.0.16 -- renewal in 41481 seconds. Jun 6 10:38:20 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:38:20 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:38:20 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:38:20 lolbox dhclient: XMT: Solicit on eth0, interval 2110ms. Jun 6 10:38:20 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:20 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:38:21 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:38:21 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:38:21 lolbox whoopsie[1133]: online Jun 6 10:38:21 lolbox ntpdate[13217]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:38:21 lolbox ntpdate[13217]: no servers can be used, exiting Jun 6 10:38:22 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:38:22 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:38:22 lolbox dhclient: XMT: Solicit on eth0, interval 4080ms. Jun 6 10:38:22 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:22 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:26 lolbox dhclient: XMT: Solicit on eth0, interval 8450ms. Jun 6 10:38:26 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:26 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:35 lolbox dhclient: XMT: Solicit on eth0, interval 16630ms. Jun 6 10:38:35 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:35 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:51 lolbox dhclient: XMT: Solicit on eth0, interval 34860ms. Jun 6 10:38:51 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:51 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:58 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:38:58 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13161 Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:22 lolbox whoopsie[1133]: online Jun 6 10:39:04 lolbox whoopsie[1133]: offline Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:39:04 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:39:04 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13160 Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:39:04 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:05 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:05 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:05 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:06 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13270 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13271 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:39:07 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:07 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:07 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:07 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:07 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:07 lolbox dhclient: All rights reserved. Jun 6 10:39:07 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:07 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:08 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:08 lolbox dhclient: All rights reserved. Jun 6 10:39:08 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:08 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Bound to *:546 Jun 6 10:39:08 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:39:08 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:39:08 lolbox kernel: [ 1446.098590] type=1400 audit(1402043948.002:75): apparmor="DENIED" operation="signal" profile="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=13273 comm="nm-dhcp-client." requested_mask="send" denied_mask="send" signal=term peer="/sbin/dhclient" Jun 6 10:39:08 lolbox kernel: [ 1446.098599] type=1400 audit(1402043948.002:76): apparmor="DENIED" operation="signal" profile="/sbin/dhclient" pid=13273 comm="nm-dhcp-client." requested_mask="receive" denied_mask="receive" signal=term peer="/usr/lib/NetworkManager/nm-dhcp-client.action" Jun 6 10:39:08 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:39:08 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on Socket/fallback Jun 6 10:39:08 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3e0183b9) Jun 6 10:39:08 lolbox dhclient: XMT: Solicit on eth0, interval 1050ms. Jun 6 10:39:08 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:39:08 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:39:09 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:39:09 lolbox dhclient: bound to 192.168.0.16 -- renewal in 35498 seconds. Jun 6 10:39:09 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:39:09 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:39:09 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:10 lolbox dhclient: XMT: Solicit on eth0, interval 2180ms. Jun 6 10:39:10 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:10 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:39:10 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:39:10 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:39:10 lolbox whoopsie[1133]: online Jun 6 10:39:10 lolbox ntpdate[13339]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:39:10 lolbox ntpdate[13339]: no servers can be used, exiting Jun 6 10:39:11 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:39:11 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:39:12 lolbox dhclient: XMT: Solicit on eth0, interval 4350ms. Jun 6 10:39:12 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:12 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:16 lolbox dhclient: XMT: Solicit on eth0, interval 8740ms. Jun 6 10:39:16 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:16 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:17 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:17 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:25 lolbox dhclient: XMT: Solicit on eth0, interval 17610ms. Jun 6 10:39:25 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:25 lolbox dhclient: IA_NA status code NoAddrsAvail.

    Read the article

  • cisco 2900xl - SNMP - Get mac address of device connected to an interface

    - by ankit
    Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

    Read the article

  • How to disable monitor auto detection in Windows 7?

    - by Jay Yother
    I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

    Read the article

  • Limit Windows PC Network/Internet Throughput

    - by Jon Cram
    I have a Vista x64 machine on a fairly fast Internet connection and either buggy drivers for the onboard Ethernet or faulty onboard Ethernet hardware. If I sustain too high a throughput on the Ethernet connection the network connection within Windows fails and I have to restart the machine to restore connectivity. I don't believe I can fix this issue (I'm erring towards faulty hardware) but would like to mitigate the effects by limiting my network throughput. I'm in a position where I would like to download a 5GB file from the Internet (a game install via Steam) and am certain that as this will take a few hours I will not be able to complete the download before my network connection within Windows fails. From downloading content through a BitTorrent client I have found that by limiting the download throughput to around 150 kilobytes per second I can maintain a steady network connection. I can't directly limit the throughput of the download through the Steam client and would instead like to find out how I can limit the throughput of my Ethernet connection within Windows. Any suggestions on how I can achieve this?

    Read the article

  • Increase data transfer speed through bonding/lacp?

    - by Matteo
    I want to maximize the throughput of a data transfer between two servers. The copy will be made at the application layer using Robocopy. To clear things up, please check my Visio schema of the network: FS1---------(SW1)===========(SW2)--------- FS2 SW1 to SW2 is connected through 10 gigabit Fiber Channel ethernet FS1 to SW1 is connected through 1 gigabit ethernet FS2 to SW2 is connected through 1 gigabit ethernet I first idea I've come up with is to use LACP, so I could use two Gigabit Ethernet between each server and the switch. A collegue told me that LACP is for availability and not performance, so he reckon this solution will not work. Is he right? Do I have other options? Thank you very much

    Read the article

  • OpenVPN Server Ethernet Bridging Question

    - by Hooplad
    Hello All, I am having a difficult time properly configuring an ethernet bridge using OpenVPN 2.0.9 install on CentOS 5 ( VPN server ). The goal that I am trying to complete is to connect a VM ( instance running on the same CentOS machine ) acting as a Microsoft Business Contact Manager server. I would then like this "BCM server" to serve Windows XP clients on 192.168.1.0/24 network as well as clients connecting from VPN ( 10.8.0.0/24 ). The setup as it is now was based off a known working configuration. The problem with the working configuration was that it would allow to the client to connect and access everything running on the VPN server ( SVN, Samba, VM Server ) but not any computers on the 192.168.1.0/24 network. I must disclose that the VPN server is behind a router/firewall. Ports are being forwarded correctly ( again, clients were able to connect to the VPN server with no problem. netcat confirms the udp port is open as well ). current ifconfig output br0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 inet addr:192.168.1.169 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:5eff:fe4d:3ac2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:846890 errors:0 dropped:0 overruns:0 frame:0 TX packets:3072351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42686842 (40.7 MiB) TX bytes:4540654180 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:882641 errors:0 dropped:0 overruns:0 frame:0 TX packets:1781383 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:82342803 (78.5 MiB) TX bytes:2614727660 (2.4 GiB) Interrupt:169 eth1 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:650 errors:0 dropped:0 overruns:0 frame:0 TX packets:1347223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67403 (65.8 KiB) TX bytes:1959529142 (1.8 GiB) Interrupt:233 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:17452058 errors:0 dropped:0 overruns:0 frame:0 TX packets:17452058 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94020256229 (87.5 GiB) TX bytes:94020256229 (87.5 GiB) tap0 Link encap:Ethernet HWaddr DE:18:C6:D7:01:63 inet6 addr: fe80::dc18:c6ff:fed7:163/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3086 errors:0 dropped:166 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:315099 (307.7 KiB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:192.168.177.1 Bcast:192.168.177.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:192.168.55.1 Bcast:192.168.55.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) current route table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.55.0 * 255.255.255.0 U 0 0 0 vmnet8 192.168.177.0 * 255.255.255.0 U 0 0 0 vmnet1 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 current iptables output Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination server_known_working.conf local banshee port 1194 proto udp dev tap0 ca ca.crt cert banshee_server.crt key banshee_server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 192.168.1.0 255.255.255.0" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 4 The following is the current CentOS server config file. server_ethernet_bridged.conf ( current ) local 192.168.1.169 port 1194 proto udp dev tap0 ca ca.crt cert server.crt key server.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.1.169 255.255.255.0 192.168.1.200 192.168.1.210 push "route 192.168.1.0 255.255.255.0 192.168.1.1" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 6 The following is one of the client's config file that was used with the known working configuration. client.opvn client dev tap proto udp remote XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca client.crt cert client.crt key client.key tls-auth client.key 1 verb 3 I have tried the HOWTO provided by OpenVPN as well as others http://www.thebakershome.net/openvpn%5Ftutorial?page=1 with no success. Any help or suggestions would be appreciated.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >