Search Results

Search found 2628 results on 106 pages for 'martin pain'.

Page 17/106 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• NIC Bonding/balance-rr with Dell PowerConnect 5324

  - by Branden Martin

  I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

  Read the article

• moving to a new dedicated server and need advice on the new setup

  - by Eric Martin

  I currently have a dedicated server that we have outgrown and we are moving to another server. Our current setup was a 8gb W2008R2 server running a W2008R2 IIS virtual machine using VMWare. We are moving to a 2 cpu 24 gb server with W2012 R2 on Hyper-V. On our virtual machine we are running iis 7.5 and sql server. Sql Server seems to want to eat up all the memory so I had to cap it at 2gb, which doesn't seem sufficient. My question is, when I move the virtual machine to the new server, should I create 2 virtual machines, one for sql server and one for IIS? Or should I leave them both on the same virtual machine? Or even, put the Sql Server on the dedicated server and run the IIS in the vm? I'd like some input on how this should be done, I've not got the experience needed to make the right call. Thanks!

  Read the article

• Bacula backup on Linux, restore on FreeBSD

  - by Martin Orda

  I'd like to migrate my storage server from Linux (Debian) to FreeBSD. Biggest part of this is restoring backups saved on Linux to tape volumes on the newly installed FreeBSD. Unfortunately I don't have anywhere to test this on at the moment but I'd like to ask you if you're aware of any incompatiblities or Bacula specific settings that should be used to make this as smooth of a process as possible.

  Read the article

• 1GB cached memory - Do I need more RAM?

  - by Martin

  The server runs well but I wonder if I should get more RAM. I only have a few MB of "free" memory and 1.2GB of "cached" memory: free: total used free shared buffers cached Mem: 3945 3893 51 0 28 1216 -/+ buffers/cache: 2648 1296 Swap: 3895 857 3038 I learned that cached memory is used while it's free and not. Is the cached value an indicator for the need of more RAM? cat /proc/meminfo 1 day after flushing the cache: MemTotal: 4040048 kB MemFree: 32844 kB Buffers: 18956 kB Cached: 1249092 kB SwapCached: 161576 kB Active: 3611328 kB Inactive: 189104 kB SwapTotal: 3989496 kB SwapFree: 2894200 kB Dirty: 20520 kB Writeback: 0 kB AnonPages: 2523496 kB Mapped: 217744 kB Slab: 70940 kB SReclaimable: 36756 kB SUnreclaim: 34184 kB PageTables: 99648 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 6009520 kB Committed_AS: 6401716 kB VmallocTotal: 34359738367 kB VmallocUsed: 18852 kB VmallocChunk: 34359719439 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB top: top - 17:20:10 up 112 days, 3:06, 1 user, load average: 1.01, 1.62, 1.48 Tasks: 208 total, 1 running, 207 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.6%sy, 0.0%ni, 97.5%id, 1.3%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 4040048k total, 3953108k used, 86940k free, 16348k buffers Swap: 3989496k total, 1095712k used, 2893784k free, 1235436k cached

  Read the article

• Is it possible to use XP visual styles (*.msstyles) or Windows Blinds in a thinapp portable applicat

  - by Camilo Martin

  It's been a while since I made a portable (Office 2007) Thinapp application, and since then I've uninstalled VMWare from my machine to free up space, so I'd like to know if someone already knows the answer to this before I set up everything again to try it. I'm thinking of installing a visual style (*.msstyles, for XP) along with the application to thinapp before post-setup capture. Failing that, maybe I'll try with visual mods such as Windows Blinds. The purpose is to be able to run a portable application with a specific visual style. So my question is: Is it possible? (I believe it somehow is, since VirtualBox does something similar to XP Mode) If it is, will it work on a computer with the "classic" Windows style? If it's not, will it work with another virtualization software? (Xenocode?) If it's not possible with *.msstyles, will it work with visual mods such as Windows Blinds? Thanks for any input! (P.S.: Awfully tagged due to lack of relevant tags or 100+ rep to create a tag :P)

  Read the article

• Subnet calculator for MS Excel

  - by Martin

  I quite often use the handy subnet calculator here: http://www.subnet-calculator.com/ Which I find very useful. However, does anyone have details/a link for a version of this that offers similar functionality but is in an excel spreadsheet. I could then include it in a worksheet and I wouldn't have to keep visiting the website. Also handy if I don't have internet access - which can often be the case when I need it. Many thanks

  Read the article

• PCI-express - is there a typo in the Intel 5500 overview

  - by Martin

  The overview for the 5500 and 5520 chipsets state that there is a total bandwidth of up to 48GB/s on each PCI Express x8 interface. http://www.intel.com/products/server/chipsets/5500-5520/5500-5520-overview.htm My understanding (admittedly from wikipedia) is that PCI-e Gen 2 runs at 500MB/s per lane. The 5520 has 36 lanes, and so would be limited to a total of 18GB/s. Am I missing something here, or is Intel's claimed 48GB/s a typo that should say 18GB/s ?

  Read the article

• Incremental backups from Rackspace Cloud Files to Amazon Glacier

  - by Martin Wilson

  Is there a software product/module (open-source or commercial) that can provide incremental backups from Rackspace Cloud Files to Amazon Glacier? We are looking for something that will provide the following functionality (or achieve the same result, i.e. a cost-effective backup strategy for files stored in Rackspace Cloud Files): Work out which files have been added to or modified in a Rackspace Cloud account (since the last backup). Create a ZIP (or similar) of these files and store them in Amazon Glacier. Keep a record of which files are in which ZIPs. Ideally, restore either a single file or all files from Glacier back into Rackspace.

  Read the article

• How can I use two Internet connections in Ubuntu?

  - by Martin

  My goal is to be able to do something like this: curl google.com --interface ppp0 curl google.com --interface p2p2 ppp0 is a DSL connection, and p2p2 is a separate direct Internet connection. Currently I can only get one of these to work at a time. When I enable one, the other one stops working. /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # DSL auto p2p1 iface p2p1 inet manual auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig p2p1 up # line maintained by pppoeconf provider dsl-provider # DIRECT auto p2p2 iface p2p2 inet dhcp ifconfig: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 p2p1 Link encap:Ethernet inet6 addr: fe80::20a:ebff:fe21:99c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p2p2 Link encap:Ethernet inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20a:ebff:fe17:1249/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ppp0 Link encap:Point-to-Point Protocol inet addr:53.193.231.167 P-t-P:53.193.224.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 10.0.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 53.193.224.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 p2p2 By default, only ppp0 works. If I run "route add default gw 192.168.1.1 p2p2" then I can use p2p2 but ppp0 stops working. If I then run "route add default gw 53.193.224.1 ppp0" then I can use ppp0 again but p2p2 stops working. What can I do to be able to use both interfaces selectively?

  Read the article

• How to backup blog running on posterous.com

  - by Martin Vobr

  I'd like to backup content of my blog which is powered by posterous.com. I'd like to save all texts and images to the local disk. Ability to browse it offline is a plus. What I've already tried: wget wget -mk http://myblogurl It downloads the first page with list of posts, then stops with "20 redirections exceeded" message. WinHttpTrack It downloads the first page with redirection to the www.posterous.com home page instead of real page content. Edit: The url of the site I'm trying to backup is blog.safabyte.net

  Read the article

• Implications of using many USB web cameras

  - by Martin

  I'm looking into connecting multiple low resolution USB webcams to a single computer. What implications might this have on performance? How does, for example, four 320x240 cameras fare against a single 640x480 camera? I'm not well versed in the architecture of the USB interface, what are the performance caveats? By performance I mean how would it affect the time to read the image data from multiple cameras compared to a single one.

  Read the article

• Advance DNS - Redirecting Emails to new webhost

  - by Martin

  I am not to sure if this question belongs here but I will surely find out soon enough. I have two web hosts (Not sure why it has been setup this way but it has). I do not want to use the original web host to handle the emails as the Data that we get from them is 500 mb which is already full with hosting the website. The second web host has an unlimited data plan and was created so we could use this host for the email accounts. Now the problem is I have reset the Advance DNS Zone records on both accounts and I am not sure what they were before. (Silly me should have taken a backup of how it was setup before hand I know) Emails were working before and going to the second hosts server now they are going to the first host but it has no email addresses setup for use so all emails are bouncing saying that the address does not exist. Host 1 IP: 192.185.96.110 Host 2 IP: 27.54.88.66 So far I have changed the Advanced DNS Zone record on Host 1 with the following: A Record: mail.australisinstitute.qld.edu.au - 27.54.88.66 I have not made any changes on Host 2 and both hosts have the default MX Records. If I need to provide any more information I can but I just hope someone can decipher what I have said haha. Cheers in advance!

  Read the article

• Problem to connect to MySQL server (error #2002) in PHP

  - by Martin

  I installed ZWAMP 1.0.7 (on Windows 7), but I'm having a weird problem. I can't connect to my MySQL server from any PHP script. If I try to use MySQL command line everything works fine but PHPMyAdmin retruns error #2002. I'm not sure whether it's important or not but MySQL server is not able to create socket file. I don't know what's the problem but I think everything is configured in my.cnf properly. Do you have any ideas?

  Read the article

• Why does StackExchange store images in imgur rather than its own servers? [migrated]

  - by martin's

  I am trying to understand the technical (and business) logic behind taking such an approach. Certainly SE isn't short of server or bandwidth resources. I don't think imgur is a CDN, so that can't be the reason. On the one hand one is giving up local control (meaning your files, your hardware) of the content. On the other, you don't have to use your own bandwidth, storage and resources. Then again, you depend on someone else for the reliability and up-time of your service.

  Read the article

• Setting up Apache and PHP on Mac OS X Snow Leopard

  - by Martin Bean

  I've recently purchased an Apple iMac. Unfortunately, enabling Apache and PHP has thrown up some problems. I enabled Mac's built-in Web Sharing through System Preferences, at which point I got an output and could add HTML files to my user directory. However, PHP files were being displayed rather than interpreted. I then discovered this is because PHP isn't enabled by default on Mac's Apache set-up. After a quick Google search, I came across this page: http://developer.apple.com/mac/articles/internet/phpeasyway.html I proceeded to the section, Enabling PHP in Apache, copying and pasting the following code snippet into a new Terminal window and hitting Return: set admin_email to (do shell script "defaults read AddressBookMe ExistingEmailAddress") user_www=$HOME/Sites filename=php-test user_index=${user_www}/${filename}.php user_db=${user_www}/${filename}-db.sqlite3 # NOTE: Having a writeable database in your home directory can be a security risk! conf=`apachectl -V | awk -F= '/SERVER_CONFIG/ {print \$2}'| sed 's/"//g'` conf_old=$conf.$$ conf_new=/tmp/php_conf.new touch $user_db chmod a+r $user_index chmod a+w $user_db chmod a+w $user_www echo "Enabling PHP in $conf ..." sed '/#LoadModule php5_module/s/#LoadModule/LoadModule/' $conf | sed "s^[email protected]^<b>\$admin_email</b>^" > $conf_new echo "(Re)Starting Apache ..." osascript <<EOF do shell script "/bin/mv -f $conf $conf_old; /bin/mv $conf_new $conf; /usr/sbin/apachectl restart" with administrator privileges EOF Unfortunately, this has completed thrown Apache and now nothing is being served; instead I'm receiving "Failed to open page" errors because it cannot connect to the server, despite Web Sharing still being active in System Preferences. So therefore I guess my question is this: how can I undo the changes made by the copy-and-pasting of the above code snippet? Admittedly, I don't understand what the above did; I just thought it looked like a Terminal command and tried it. I have no experience in setting up Apache on Mac OS X (and I've only installed XAMPP and WampServer on Windows). So any points on reversing the aforementioned, and then successfully enabling PHP would be great. EDIT: I've discovered, via Console, the following error message is being recorded when trying to browse to 127.0.0.1... (org.apache.httpd) Throttling respawn: Will start in 10 seconds no listening sockets available, shutting down Unable to open logs (org.apache.httpd[13453]) Exited with exit code: 1 Does this point any more to the issue? EDIT #2: I'm now getting this in Console... 15/02/2010 21:24:14 osascript[3597] Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found. Did find: /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper

  Read the article

• Thunderbird confused about EPS attachments

  - by Martin

  Sometimes, when I receive (Thunderbird 2.0.0.23 on OS X 10.5) emails with an EPS attachement sent from Mail OS X 10.4, I cannot open the EPS file. Thunderbird shows me 1 file, that can't be opened with any software but text edit. But, if I forward the email to myself, the forwarded email then has 2 files of the same name. One of the 2 forwarded files can be opened as expected. What can be wrong here?

  Read the article

• find command in Linux

  - by Martin

  My goal is to find all pdf files on a remote machine, so I resort to the useful command find. So I type find ~ *.pdf or find ~ "*.pdf" and I get nothing. I do the same on my machine and I get nothing. I do a regular search from the menu on my machine and I find quite a few pdf files. Would somebody please tell me what am I doing wrong?

  Read the article

• Forwarding email to mydomain.com

  - by Martin

  Newbie question: I've got the following set up, the server 2008, the iis and the smtp. I've my mydomain.com set up with DNS pointing to my public ip, www and smtp both. Now I'll be sending alot of emails from my web app to people and this works fine. What I also want is for people to be able to send us email. Please point me in the right direction. Primary objective: [email protected] -- [email protected] Secondary objective, for extra love: [email protected] -- [email protected] and [email protected] -- [email protected] Do I need a popserver? Any tutorials people can recommend? Addition: And the MX. I've also pointed the MX record to my ip.

  Read the article

• What's the downsides of Running Ubuntu 9.10 32bit on AMD64 Processor

  - by Omar Dolaimy

  Hi, I was thinking about installing Ubuntu 9.10 32bit on a DELL Inspiron 1501 with 64bit processor Laptop. Since It's was real pain to me to run Java Browser plugin, Flash Plugin, J2ME Toolkit, and many other tools. But It was 90% OK with me. This was Ubuntu 8.10 (a year ago), And now the Ubuntu 9.10 came and I'm thinking about installing the 32 bit on it and get rid of the pain. Is there a downside for that?? considering that the display card is not supported now so exclude this from your calculation, I will never play REAL games on it and I'm not a big fan of Compiz effects. I'm not here to ask about the performance (which is about 15%+ for the 64bit only), I just want compatibility!

  Read the article

• How do I figure out what is changing the userWorkstations attribute in Active Directory?

  - by Martin

  I just took over the IT for a medium sized business with a three domain controllers (2003/2008 Standard) and whenever I create a new user, after some time the user account cannot log into most machines on the network. I have traced this back to the "Log On To..." area becoming populated with a small list of machines. Even when I set the option to all computers, this list comes back after some time. I started hunting for vbs and ps1 scripts with the word "workstations" in them on all domain controllers to see if there is some kind of script to blame, but I have thus far come up empty handed. Is there a known software suite that can cause this (Microsoft Forefront, etc)? How can I figure out what is causing this list to change?

  Read the article

• mini linux for browsing media playing

  - by Martin Beckett

  I'm looking for a small linux install (<100Mb) that can just run a browser and ideally a media player. It's to fit in a spare recovery partition on my laptop and be a quick boot for non-work stuff when I'm on the road. I have used Puppy-linux and DSL before but they have lots of stuff I don't need. Is there something like these that just concentrates on running a browser in the way xbmc does for videos? ps. The size requirement was to fit in the existing 100Mb win7 recovery partition, but that can be resized. The main idea was something that booted very quickly without the 10min wait while windows does all the corporate stuff and realizes it isn't on the LAN - and could be shutdown instantly.

  Read the article

• Migrate data from SQL Compact to SQL Server 2008

  - by Martin

  I need to do a one-time migration of data from SQL Server Compact Edition to SQL Server 2008 Express Edition. I'm looking for a tool to do this kind of migration. I've tried using Import and Export Data in SQL Server, but it doesn't let me import from SQL Server Compact Edition. Anyone knows of a easy way to do it?

  Read the article

• Debugging IO limitation

  - by Martin F

  I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

  Read the article

• Configuring Apache reverse proxy

  - by Martin

  I have loadbalancer server and edges. I am trying to configure reverse proxy in order to hide the backend servers PL1,2,3. PL 1,2,3 are not located in same subnet. They are located in different locations. PL1 Lb1 -> PL2 PL3 I tried to configure Apache reverse proxy but it is not sending request to PL1,2,3. Reverse proxy worked only when I configured apache to send request to local server on other port. ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /PL1 http://PL1server.com/ ProxyPassReverse /PL1 http://PL1server.com/ The above configuration did not worked. Could you help me to solve the issue. Or is there other proxy types like Squid,Socks5 to solve this issue. Does the reverse proxy fails if we use IP address or domain URL in ProxyPass and ProxyPassReverse ?

  Read the article

• Connecting to a remote mysql server from a windows machine (XP)

  - by Samuel Martin

  I am trying to connect to mysql server which is installed on my home pc from another pc. I allowed all connection in mysql configuration. There's no firewall blocking on the pc I am trying to connect from. I used the command- mysql -h Some.Host.IP -u SomeUser -p SomePassword I am getting- ERROR 2003 (HY000): Can't connect to MySQL server on 'Some.Host.IP' (10060) I can connect through php!! What's the problem? How do I solve it?

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >