Search Results

Search found 10936 results on 438 pages for 'monitor refresh rate'.

Page 17/438 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Why is text on my TV monitor all grainy?

  - by searchfgold6789

  I have successfully installed the Catalyst drivers and hooked up my 1080p TV to the Radeon HD 5750's HDMI port and now it is working. There only seems to be one issue - most images appear OK, at least to my eyes, but text is grainy and difficult to read (not sure how well it can be seen in the picture): It works fine with a smaller screen, and hopefully you can see it with the new pictures which are only slightly better, but images are rendered a little funny too. Changing antialiasing does nothing and changing the refresh rate only makes a slight change if any. The small monitor I have works fine. Smaller resolutions such as 1024x768 look OK but are the wrong aspect ratio. I have tried renaming the input mode on the TV to "PC", and that helped... a little bit. Also, I tried a different PC with the same result. Messing around extensively with the ATI Catalyst Control Center also did not help. I am wondering if there is anything else I can try to increase the quality so it is more usable.

  Read the article

• how do I get dual monitors to work properly in Ubuntu 11.10 on a Dell Latitude D630?

  - by wes cook

  I have spent a lot of time trying to get dual monitors to work on Ubuntu 11.10 on my Dell Latitude D630 (nVidia NVS 135m video card). - For starters, the System Displays settings app always only showed one unknown monitor, even though I had the external Acer monitor connected. - So I downloaded and installed the nVidia drivers. According to what I read I would need to only use the nVidia driver app (nVidia X Server Settings), so that's what I've done. (System Displays settings continued to only show a single monitor anyway). - nVidia settings app only showed on monitor until I changed the BIOS setting to use the onboard video for external monitor (not the dock video, which it was set to, even though I don't have a docking station). - The nVidia setting app now recognized both monitors. So, I setup the X Server display config as Separate X screen for both monitors. My laptop screen shows up as AUO 1440x900 and my external monitor as Acer E211H 1920x1080. - Everything seemed like it would work, but the external monitor was just a complete white screen. The external monitor was non-functional, even though sometimes it would show the background image - still nothing would show up over there. - So, I checked the Enable Xinerama box. - Now, after logging out and back in, the wallpaper extends to both screens but I get no taskbar at the bottom or top, no system menus, and I have to press the power button to restart or log off. - After experimenting with all the shells, the only one that shows the menus and taskbars when I log in is Gnome Classic. - This is pretty much the same symptoms as found here: How do I fix 11.10 GUI?. - So, I resign myself to the older shell. - Everything works fine until ... I unplug the external monitor ... this is a laptop after all. - Anyway, after doing some work on the road, I plug back in and I still see both screens and it's functional except, ... - Now, the laptop screen (with the taskbar and menu bar) has 4 black bars at the top that windows cannot cover. The top bar is the menu bar (with Applications, Places, the date and time and the system menu on the right). But the next 3 bars (the same height as the top menu bar) are empty and are just reducing the max size of windows on that screen. - See screenshot here: http://i39.tinypic.com/35d2kh1.png - So ... 1. How do I get rid of those extra 3 black bars? They're taking valuable screen space. 2. (less critical) How do I successfully use both screens in the Ubuntu or Ubuntu 2D shell?

  Read the article

• How can I refresh a document I have open in Excel in read-only mode?

  - by RoboShop

  I have an Excel document that is stored on a SharePoint Server, which I always have open on my computer in read-only mode because I need to refer to it. Every so often, in order to get the latest changes, I have to close down the file and reload it again. Are there any options within Excel 2007 which allow me to simply refresh a document I have open in read-only mode to the latest version on the server? Better still, is there a way where this could be done dynamically, without me having to hit refresh?

  Read the article

• What is the easiest way to make your browser refresh a page every say, 5 seconds?

  - by Oren A

  Is there a browser that supports refreshing a page every say, 5 seconds? Is there an add-on? If not, is there a more simple way than writing a full (C# or Java) program in order to do that? Added: Opera is horrible! I set Stack Overflow to refresh every 5 seconds, but when I click on a post, it refreshes it every 5 secs too! I just wanted the main page to refresh every 5 seconds. Another "Added": apparently it refreshes the current tab, so as long as I open the post in a new tab, it works great.

  Read the article

• gnome-shell failed to launch when dual monitor detected, nvidia card

  - by Terry Hu

  I installed a clean precise. I like gnome-shell so I installed it. It worked well with single monitor. But It does not work well when I go to office, plug my external monitor onto my laptop. I am using nvidia driver. Another colleague is using the same laptop, he can work well with dual monitors. His laptop is ATI graphic card. When I plug my extended monitor cable, I choose GNOME, but actually it goes to gnome 2 classic desktop environment, not GNOME 3. When I disconnect the extended monitor, restart X, I can login with GNOME3. Do I have to choose between GNOME3 and extended monitor? It's a hard choose.

  Read the article

• How do I rotate my monitor using xorg?

  - by user1106405

  I have just installed KUbuntu 12.10, and I am attempting to rotate my monitor 90 deg to the left. When I add the option to rotate, the monitor seems to ignore the directive. I'm currently using dual 02:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) and NVidia driver version 310 My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 304.51 (buildd@komainu) Fri Oct 12 12:53:49 UTC 2012 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 310.14 ([email protected]) Tue Oct 9 13:04:01 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 1280 0 Screen 1 "Screen1" RightOf "Screen0" Screen 2 "Screen2" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Samsung SyncMaster" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 60.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1908WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 1 EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select @1920x1080 +0+0; DFP-0: nvidia-auto-select @1920x720 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-2: nvidia-auto-select +0+0" Option "Rotate" "left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Enable" EndSection Edit: If I delete the xorg.conf and reboot, I am able to rotate my monitor, however, my third monitor is not recognized: Screen 0: minimum 8 x 8, current 3360 x 1200, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 disconnected (normal left inverted right x axis y axis) DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm 1920x1200 60.0*+ 1600x1200 60.0 1280x1024 60.0 1280x960 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-I-3 connected 1440x900+1920+0 (normal left inverted right x axis y axis) 408mm x 255mm 1440x900 59.9*+ 75.0 1280x1024 75.0 60.0 1280x800 59.8 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 640x480 75.0 72.8 59.9

  Read the article

• Pivot Table Does Not Refresh Source

  - by AME

  Typically, when selecting a data source for a pivot table in Excel 2013, it is possible to refresh the table by selecting "refresh table" or "refresh all". This triggers an update in the Pivot Table based on changes in the underlying data source. However, I am running into a case where this functionality does not prompt a refresh of the pivot table. What might be causing the pivot table in Excel 2013 to remain static when selecting "refresh data"?

  Read the article

• ATI card - cannot set refresh rate higher than 60 Hz

  - by KubaV

  I am trying to set refresh rate to 85 Hz or 75 Hz at 1024x768 and 1280x1024. On Windows this works, so my card and monitor have 100% support. xrandr does not work - it gives me configure crtc 1 failed I use FGLRX. Please help Monitor:CRT - HP 92 (manual http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/lpv09818/lpv09818.pdf) G. card: AMD Radeon HD 6450 Sorry for bad english, I am Czech.

  Read the article

• monitor http request from non-browser

  - by Ananth

  hi, I want to monitor http request generated out of a exe. Is there any tool that can help me? Actually, an exe would call my asp.net web page to register a user. The exe constructs the POST data request and calls my page. when the request reaches my web page, I don't see any data. I want to monitor the Request object and the traffic to find the reality. Any help is appreciated. Thanks. ~/Ananth

  Read the article

• Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

  - by John C

  I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

  Read the article

• Why is WSXGA+ 1680x1050

  - by Bart van Heukelom

  Like the title says, why? Why not the more convenient 1600x1000? Likewise, why 1280 x 800 and not 1200x750?

  Read the article

• Windows being placed on wrong monitor

  - by osarusan

  I'm running a fresh install of Ubuntu 12.04x64 (ATI Radeon HD4770 with open source drivers) and I am having trouble getting windows to appear on the right screen. Yesterday I plugged in my secondary monitor and it worked perfectly out of the box, except that for some reason, compiz wants to place windows on the secondary monitor rather than the first. This is a problem because I don't use the secondary monitor 100% of the time, and I don't want windows being placed on it when it is off. Also, it's only some windows that are getting placed there. For example, the "Edit Connections" window from the networking menu is always placed off my primary screen. There are a number of other windows that do the same. While some, like nautilus, always appear on the proper monitor. I played around with Compiz Config Settings Manager and found that if I disable the "Place Windows" plugin, all of the windows appear on the proper monitor -- except that they are placed underneath the Unity Panel, so I have to alt-drag them out each time in order to use them. With out without that plugin, I can't seem to get a sensible setup. The windows are supposed to appear only on the active display, but for some reason Compiz doesn't want to do that with some windows. Does anyone know a fix for this? I'd rather not have to disable and re-enable my monitor every single time I use it...

  Read the article

• Automatically revert to laptop screen when external monitor unplugged

  - by Ryan

  I regularly use an external monitor with my laptop, so when I use it, I usually have the laptop screen disabled when the monitor is connected, and this seems to cause problems when the monitor is disconnected. If the monitor is connected while the laptop screen is disabled, I can't get the X session to show up at all: I can Ctrl+Alt+F1 to open a terminal, and that works fine.. ..but Ctrl+Alt+F7 does nothing. The display is blank, and stays blank. The same thing happens whether I put the computer to sleep with the monitor connected, or if I disconnect while the computer is still awake. Rebooting the computer fixes the issue, as does killing Xorg and starting it again, but both of those are sub-optimal since I lose my current session. I'm currently using the open source graphics driver (xserver-xorg-video-ati). This question looks like it might answer my question, but unfortunately hwinfo is no longer available in the apt repository. Is there a way with current tools to automatically detect when the external monitor is disconnected and switch to the laptop display?

  Read the article

• One monitor getting spilled over into other monitor: how to do a 100% reset of gnome graphics configuration

  - by Paul Nathan

  I had to kill a VMWare process and afterwards, my monitor's configuration is buggy. I have 2 monitors in a side-by-side configuration. My right-hand monitor is the secondary monitor. Upon its right-hand side there are about 50 pixels showing from the left side of the lefthand monitor (ie, as if it was wrapped around). Further, my mouse clicks are registering as about 50 pixels sideways from where they should be. It's as if those 50 pixels between monitors got gobbled. What have I done? I've reset the screen configuration in multiple ways, using xrandr, multiple monitors app, etc. This persists in different side-by-side configurations, and also persists with another user. It does not occur with XFCE. Resetting the Window manager with the Compiz reset WM app does not fix this. I've concluded the burn-to-the-ground approach is likely the best, and would like to do a 100% reset of my graphics settings. It's an Intel integrated chipset. Removing ~/.config/monitors.xml did not work. Also, interestingly, the mouse can mouse-over the 50 errant pixels on the rhs of the right-hand monitor. I hypothesize that it's a compositing problem occurring at the layer where the background, selection, and clicks are caught. Also, inverting the right-hand monitor removes the issue, but renders the screen unusable. Even more datapoints: This happens in KDE as well Sometimes logging into Gnome and running xrandr --output DVI1 --auto resets it, but the issue immediately reappears when I press alt-tab. With Compiz Application Switch turned on, the workspace is 'pushed back' a bit, and the slice on the RHS follows it as well. I'm wondering if it's a flaw in the compiz workspace compositing configuration. I suspect the error was in the compositing configuration. I installed 11.10.

  Read the article

• Automatic switching between monitor configurations

  - by Michael Aquilina

  I have a laptop and an external monitor and i was wondering if there was a simple approach to switching between multiple monitor configurations based on the detected available displays. For example: When i am at home and i plug in my external monitor i would like this to automatically become enabled and the laptop screen to become disabled. As soon as i pull out the display cable for the external monitor, i would like the laptop screen to automatically become enabled. I was expecting this to just "work" just like it does in windows - but it seems to be much harder than that. I am aware of the xrandr command to turn displays on and off but i cannot seem to find a way to get this to work the way i describe above. I had also found this post about switching between multiple monitor configurations and the results seem a bit inconclusive. However i was hoping that with xrandr there would be a simpler solution. For me, the fact that when i pull out my external monitor the screen just goes black and i get an error message is a big issue holding me back from making the complete switch to linux as i move around alot as a student. My OS of choice is currently Kubuntu 12.04 but i am willing to change to something else if it provides a better way of setting up the described setup.

  Read the article

• Eclipse: How do i refresh an entire workspace? F5 doesn't do it.

  - by Jack

  I have a workspace with a bunch of java projects. If i go to File-Refresh, it doesn't really refresh anything (perhaps the currently selected project). How do i get eclipse to refresh all of the projects?

  Read the article

• Can a 10-bit monitor connection preserve all tones in 8-bit sRGB gradients on a wide-gamut monitor?

  - by hjb981

  This question is about color management and the use of a higher color depth, 10 bits per channel (30 bits in total, resulting in 1.07 billion colors, or 1024 shades of gray, sometimes referred to as "deep color") compared to the standard of 8 bits per channel (24 bits in total, 16.7 million colors, 256 shades of gray, sometimes referred to as "true color"). Do not confuse with "32 bit color", which usually refers to standard 8 bit color with an extra channel ("alpha channel") for transparency (used to achieve effects like semi-transparent windows etc). The following can be assumed to be in place: 1: A wide-gamut monitor that supports 10-bit input. Further, it can be assumed that the monitor has been calibrated to its native gamut and that an ICC color profile has been created. 2: A graphics card that supports 10-bit output (and is connected to the monitor via DisplayPort). 3: Drivers for the graphics card that support 10-bit output. If applications that support 10-bit output and color profiles would be used, I would expect them to display images that were saved using different color spaces correctly. For example, both an sRGB and an adobeRGB image should be displayed correctly. If an sRGB image was saved using 8 bits per channel (almost always the case), then the 10-bit signal path would ensure that no tonal gradients were lost in the conversion from the sRGB of the image to the native color space of the monitor. For example: If the image contains a pixel that is pure red in 8 bits (255,0,0), the corresponding value in 10 bits would be (1023,0,0). However, since the monitor has a larger color space than sRGB, sending the signal (1023,0,0) to the monitor would result in a red that was too saturated. Therefore, according to the ICC color profile, the signal would be transformed into a different value with less red saturation, for example (987,0,0). Since there are still plenty of levels left between 0 and 987, all 256 values (0-255) for red in the sRGB color space of the file could be uniquely mapped to color-corrected 10-bit values in the monitor's native color space. However, if the conversion was done in 8 bits, (255,0,0) would be translated to (246,0,0), and there would now only be 247 available levels for the red channel instead of 256, degrading the displayed image quality. My question is: how does this work on Ubuntu? Let's say that I use Firefox (which is color-aware and uses ICC color profiles). Would I get 10-bit processing, thus preserving all levels of an 8-bit picture? What is the situation like for other applications, especially photo applications like Shotwell, Rawtherapee, Darktable, RawStudio, Photivo etc? Does Ubuntu differ from other operating systems (Linux and others) on this point?

  Read the article

• Second Monitor stays black/in power save mode

  - by Rob

  I'm using two Monitors, a Belinea o.display 1 (Recognized as a Rogen Tech Distribution Inc 20" by Ubuntu, but working fine) on the DVI-Output (connected via DVI-to-VGA-adapter) as my primary Monitor and a Dell 19" (Recognized correctly) on the HDMI-output (via HDMI-to-DVI adapter) as secondary monitor. The graphics controller is a GeForce 9500 GS. I'm running a fully updated Ubuntu 13.04 with nouveau 1:1.0.7-0ubuntu1. The problem is that the second monitor (Dell) never seems to come out of standby during boot: the screen stays black and the status led on the monitor stays orange (it's green when it's on). It is correctly recognized an the size of the desktop is set accordingly, it just stays black. Changing any setting via xrandr/arandr/etc. does nothing. The on-screen-menu of the monitor reports it to be in power save mode. When using the proprietary NVIDIA-Drivers, the second monitor works just find. But these drivers cause a lot of other problems on my system, so i would really like to avoid them. On Ubuntu 12.10 i had found a workaround: When moving the relative position of the second monitor slightly down and the up again, it would turn on and function normally: xrandr --output DVI-I-1 --mode 1680x1050 --pos 1280x0 --rotate normal --output HDMI-1 --mode 1280x1024 --pos 0x88 --rotate normal sleep 2 xrandr --output DVI-I-1 --mode 1680x1050 --pos 1280x0 --rotate normal --output HDMI-1 --mode 1280x1024 --pos 0x0 --rotate normal This workaround stop working after the update to 13.04, and now i'm looking for a new solution. Has anyone experienced something similarity? xrandr output: Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 8192 x 8192 DVI-I-1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 433mm x 270mm 1680x1050 60.0*+ 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1024x768 75.1 72.0 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 HDMI-1 connected 1280x1024+1680+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 lshw -c video: *-display Beschreibung: VGA compatible controller Produkt: G96 [GeForce 9500 GS] Hersteller: NVIDIA Corporation Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Version: a1 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress vga_controller bus_master cap_list rom Konfiguration: driver=nouveau latency=0 Ressourcen: irq:16 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:df00(Größe=128) memory:fb000000-fb07ffff Thanks for your help!

  Read the article

• AAC Sample Rate and Bit Rate for High Quality Audio?

  - by marco.ragogna

  What are the AAC Sample Rate and Bit Rate settings to set in order to encode an audio track with a quality comparable to MP3 320kbps? I need to backup a DVD movie, the default settings for AAC are Bitrate (KB/s) 128 Sample Rate (HZ) 44100 should I set Bitrate (KB/s) 320 Sample Rate (HZ) 48000 or the default are already good?

  Read the article

• How can I increase Emacs key repeat rate in OS X Mountain Lion

  - by Rob Jones

  Emacs does not seem to respect the OS's key repeat rate. I'm using emacs in the terminal. I've set the repeat rate to as fast as possible by directly editing the settings in the following file (I restarted after making the change): open ~/Library/Preferences/.GlobalPreferences.plist The rest of the system observes the repeat rate. The terminal works as expected, as does vim. But, when I use emacs I still get the annoyingly slow repeat rate.

  Read the article

• Time based movement Vs Frame rate based movement?

  - by sil3nt

  Hello there, I'm new to Game programmming and SDL, and I have been following Lazyfoo's SDL tutorials. My question is related to time based motion and frame rate based motion, basically which is better or appropriate depending on situations?. Could you give me an example where each of these methods are used?. Another question I have is that, in lazyfoo's two Motion tutorials (FPS based and time based) The time based method showed a much smoother animation while the Frame rate based one was a little hiccupy, meaning you could clearly see the gap between the previous location of the dot and its current position when you compare the two programs. As beginner which method should I stick to?(all I want is smooth animations).

  Read the article

• Monitor System Resources from the Windows 7 Taskbar

  - by Asian Angel

  The problem with most system monitoring apps is that they get covered up with all of your open windows, but you can solve that problem by adding monitoring apps to the Taskbar. Setting Up & Using SuperbarMonitor All of the individual monitors and the .dll files necessary to run them come in a single zip file for your convenience. Simply unzip the contents, add them to an appropriate “Program Files Folder”, and create shortcuts for the monitors that you would like to use on your system. For our example we created shortcuts for all five monitors and set the shortcuts up in their own “Start Menu Folder”. You can see what the five monitors (Battery, CPU, Disk, Memory, & Volume) look like when running…they are visual in appearance without text to clutter up the looks. The monitors use colors (red, green, & yellow) to indicate the amount of resources being used for a particular category. Note: Our system is desktop-based but the “Battery Monitor” was shown for the purposes of demonstration…thus the red color seen here. Hovering the mouse over the “Battery, CPU, Disk, & Memory Monitors” on our system displayed a small blank thumbnail. Note: The “Battery Monitor” may or may not display more when used on your laptop. Going one step further and hovering the mouse over the thumbnails displayed a small blank window. There really is nothing that you will need to worry with outside of watching the color for each individual monitor. Nice and simple! The one monitor with extra features on the thumbnail was the “Volume Monitor”. You can turn the volume down, up, on, or off from here…definitely useful if you have been wanting to hide the “Volume Icon” in the “System Tray”. You can also pin the monitors to your “Taskbar” if desired. Keep in mind that if you do close any of the monitors they will “temporarily” disappear from the “Taskbar” until the next time they are started. Note: If you want the monitors to start with your system each time you will need to add the appropriate shortcuts to the “Startup Sub-menu” in your “Start Menu”. Conclusion If you have been wanting a nice visual way to monitor your system’s resources then SuperbarMonitor is definitely worth trying out. Links Download SuperbarMonitor Similar Articles Productive Geek Tips Monitor CPU, Memory, and Disk IO In Windows 7 with Taskbar MetersUse Windows Vista Reliability Monitor to Troubleshoot CrashesTaskbar Eliminator Does What the Name Implies: Hides Your Windows TaskbarBring Misplaced Off-Screen Windows Back to Your Desktop (Keyboard Trick)How To Fix System Tray Tooltips Not Displaying in Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites

  Read the article

• Authorship tag or Customer reviews to enhance click-through rate

  - by Prashant Singh

  I was first using authorship tag on all the pages of my website. That gave me a pretty decent improvement in the click through rate. However, I have recently added ratings on my website, i.e. all my pages are being rated by the readers and the same has been made available to Google via rich snippets. The result being the image of the author from the google search results has been removed. It shows ratings given by the customers and just writes the name of the author. What will be its impact on the click-through rate ? Is it OK to have the ratings or should I switch back to only authorship tag as I was using in the past ? Please comment if I am unclear in asking my problem. Thanks :)

  Read the article

• Why does my monitor have a black screen but the power light is blinking green?

  - by Chris Vesper

  I have a ViewSonic VA912b 19" display I use as a secondary monitor. When I turn it on, the power light is green for a few seconds, and then switches to blinking green. The display stays black. Windows thinks the monitor is on, as it shows up in the control panel as a second monitor. If I unplug the DVI cable, it displays a "No Signal" message and the power light goes to amber, which means it went to sleep.

  Read the article

• Is there a way to force the monitor to power off in Windows 8?

  - by Rune Jacobsen

  I have googled this a bit and looked at powrprof.dll and PsShutdown but I haven't found a way to do exactly what I want to do. You know that power save option that lets Windows turn off your monitor(s) if you haven't touched the system for x amount of time? Well, I have a PC that needs to be on most of the day (and night), and I have to watch it much of the time, so I can't have a short timeout for automatically turning off the monitor. However, once I leave it for a few hours (happens at varying times of the day), I would like to be able to issue a command that puts the computer in this mode. Not sleep mode, not hibernate mode. Monitor off, that is all. I realize of course I could just turn the physical monitor off. That is not what I want. This Dell monitor takes forever to display a picture from a cold state. If it is turned off by the computer not sending a signal - not so bad. Is there any way for me to do this? As mentioned, the OS can do it, so I would find it really useful if I could do it too. :)

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >