Search Results

Search found 693 results on 28 pages for 'mutli wan'.

Page 17/28 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• What's constitute an entry on the IPTables and how to find out which client it is originated from

  - by cbd

  I have a Billion BiPac 7700N Modem/Router/Access Point and I connect another router (TP-Link TL-WR1043ND) in wan-bypass mode to extend the wireless coverage. Lately, I noticed that the connection through TP-Link has been dropping out quite regularly. Having read some posts on the Internet, I checked system log on 7700N and found that there are…

  Read the article

• Edimax wireless router is not providing DNS services correctly

  - by Nathan Fellman

  I have an Edimax router that is set up to connect to the internet via L2TP on cable, and on the LAN side it's set up as a DHCP server. The DHCP server gives correct IP addresses, but it sets itself up as the DNS server. However, it doesn't provide the DNS service. I am sure that it's a problem with the router, because I have two computers on…

  Read the article

• SNMP counter issues with cisco RV082

  - by Chance

  Does anyone else poll this router with SNMP? We are using firmware version: 2.0.0.19-tz We are having problems with the traffic counters, some of them appear to be implemented as 16 bit counter instead of 32 bit counters. The reason this is causing problems is that they roll over (at 65,000) to 0 in less than our minute polling cycle, really…

  Read the article

• Asterisk: Forcing a sip peer to connect via ipv6?

  - by growse

  I've got an asterisk server that connects to an upstream provider over a WAN. The upstream provider supports both IPv4 and IPv6 connectivity, and the asterisk server is behind a NAT. When asterisk connects to the upstream sip peer via IPv6, everything works perfectly. The issue I have is that when I configure the asterisk server IPv6…

  Read the article

• website not accessible with IIS6 while NAT is configured in Windows 2003

  - by Mohammed Rizwan

  I have Windows2003 server configured with IIS 6. Until now it was working fine, but since I enabled NAT for my users to access the internet via this server, the website becomes unavailable. Note that I have two nics on the server one is WAN and 2nd is for LAN. Both IPs are behind the firewall. If I stop the NAT then the website is…

  Read the article

• How to format HDD with MHDD Tool.

  - by PP

  I have copied MHDD application on a bootable CD and i wan to use it to low level format my HDD which had some bad sectors on it. so how can mark these badsecotrs using MHDD application? Pluse can i partition/format my HDD using MHDD because after low level format i want to setup window xp on that drive. can some one explain me…

  Read the article

• Updating Cisco VPN config to add vpnc support

  - by Igor Kuzmitshov

  I have a Cisco 1841 configured for VPN connections of two types: Peer-to-peer for partners' routers (IPsec) — using different crypto isakmp key and crypto map with set peer, set transform-set, match address for every peer (same map name, different priorities). That crypto map name is added to the WAN interface. Client access…

  Read the article

• Ubuntu Server 12.04 as a router. Problem with DNS

  - by Lorenzo

  I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean…

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is…

  Read the article

• CISCO 2911 Router configuration

  - by bala

  Device cisco 2911 router configuration support is required please. I have exchange server 2010 configured and working without any errors the problem is in cisco router configuration when exchange server sends emails out the receives WAN IP not the public ip. I have configured RDNS lookups with our MX record IP addesses that…

  Read the article

• How to tell Windows 7 to ignore a default gateway

  - by zildjohn01

  I currently have 2 network cards in my PC -- one connected to an internal network on a router with a disconnected WAN port (10.x.x.x), and one connected to the internet through a consumer router (192.168.0.x). Windows seems to recognize them correctly (my "Network and Sharing Center" lists them as "No Internet" and…

  Read the article

• Access Other Computer via ADSL Modem and Router

  - by Sohail

  My network configuration is like this ISP - Modem - Router - Computer and the same goes for my friend. We want to share large files or to access each other's computer. The Passwords to login to the web page of each other modems are known. I mean, we can access each other Modem Web GUI easily ( because we know the…

  Read the article

• Installing router - failed to verify router settings

  - by Andi

  I'm trying to install a TP-Link wireless router. I am using a modem an have a PPPoE connection. I connected the router to the computer and the modem, but in the last step of the Easy Setup it says " Failed to verify router settings. 1. Please check the WAN connection type and parameters. 2. Please check your…

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the…

  Read the article

• Urgent SSH Local Port Redirection

  - by Salina Odelva

  Hi, everyone. I have a shell account but the admin has restricted ssh access to the server. The server is listening on 0.0.0.0:22 but the firewall blocks any incoming attempts to this port. He says he is doing maintenance but I don't believe him and I need to backup my stuff with ssh. My question is that:…

  Read the article

• Monitoring bandwidth/latency/jitter between 2 sites?

  - by TheCleaner

  I have 2 sites connected via an MPLS network and I'd like to do the following: setup a host on each end that can "talk" back and forth between each other and somehow report/log what kind of throughput, jitter, latency, etc. they are experiencing between each other in 5 minute intervals. Something…

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user53864

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to…

  Read the article

• Apache doesn't autostart because vpn isn't up yet.

  - by Col. Shrapnel

  I have a FreeBSD8 server, and VPN connection to my ISP. I use mpd5 and it works fine. A have an Apache server whch works fine, if I start it manually, after VPN is get up. But when I add it to rc.conf autostart, it fail to start, saying (49) can't assign requested address: make_sock could not…

  Read the article

• Microsoft Forefront Management Gateway 2010 - Which topology to choose for monitoring only server?

  - by MadBoy

  Hello, I've installed Forefront and wanted to use it as monitoring traffic solution until we decide to put it as a router. I've 2 nic's assigned to this virtual machine. One NIC has connected port which is "mirror port" of our WAN redirected on switch so it sees all the network traffic flying…

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other…

  Read the article

• Port based bandwidth shaping

  - by nixnotwin

  I have an interent connection with the speed of 4000k bits up and down. I want to do port based traffic shaping on a ubuntu machine, which acts as router. eth0 is the WAN interface. This is how I would like to allocate bandwidth: For ports 80 and 445 the bandwidth usage can go upto 90% For…

  Read the article

• Cisco T1 Routing Help

  - by Joseph

  Thanks to someone on this site I was able to get the Serial0/0 interface up. I now have: DCD=up DSR=up DTR=up RTS=up CTS=up My next challenge seems to be in the routing and/or PC ip setup. This are the pertinent details from L3: WAN Network: 6.59.186.60/30 Level3 Side: 6.59.186.61…

  Read the article

• Google Docs: Tie the Form with a Spreadsheet to email addresses and responses?

  - by Nick Gorbikoff

  Hello. I'm just trying to figure out if I'm doing something wrong or it's not possible. I created a small form ( I'm trying to get current mailing addresses from my friends and relatives - since I lost my address book) and it ties to a Google Spreadsheet. I sent out a sample to my work…

  Read the article

• faking NAT with a VMware distributed switch across multiple hosts

  - by romant

  I need to construct a NAT for certain machines within the network. Wish to do this with dvSwitch - as it seems the logical way of attacking the problem as in this scenario there's just under 30 hosts. In order for the NAT'ed VM's to have access to the 'real' network. I am providing a…

  Read the article

• My D-Link's Ethernet bridge downlink just got 10-30x slower?

  - by Jay Levitt

  TL;DR: I unplugged my network to move my desk, and now downloading via my DIR-655's Ethernet LAN bridge is 10-30x slower than the Ethernet switch it's plugged into. Background My network is SMC cable modem <-> Cisco firewall <-> Netgear switch <-> D-Link WiFi† …

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >