Search Results

Search found 1489 results on 60 pages for 'peter carrero'.

Page 17/60 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• VMXNET3 nic loses the ability to update ARP table after N hours

  - by Peter

  I have a fedora 18 VM that stops updating the arp table on eth1 after running for a number of hours to days. There are other VMs on the same hypervisor that can access all of the same networks without issue. A tcpdump of the offending NIC shows only ARP broadcasts but no responses. None of the other VMs on the vDS see the ARP broadcasts from the offending NIC. The only way I can currently solve the problem is to reboot the VM and then everything works for a while. I've tried changing the port on the vDS and even flipping the network configurations after I lose eth1's ARP table, but the ARP problem follows eth1 but I can access the machines that were originally on eth1. If I statically add the arp entries for machines on the same subnet I have no problems with connectivity. The Hypervisor is an HP BL49X series with flex-10 network modules. Has anyone seen anything like this before?

  Read the article

• KB2494088 Always Fails : How to get it to install (or stop trying to)?

  - by Peter K.

  I have a problem where KB2494088 (a SQL Server 2008 R2 patch) continually fails to install when I reboot my system. Downloading the manual patch and trying to apply it says: The SQL Server patch package is part of a general distribution release (GDR). This package cannot be applied since this SQL Server feature has already been patched. To continue, you must install a higher version of the SQL Server patch. Most other posts (this, this) suggest it's either a failed (or cancelled) past installation or requires a SQL server repair. I've looked at registry settings and tried the repair option, but nothing seems to work.

  Read the article

• Open Microsoft Publisher Document on Linux

  - by Peter

  I'm pretty sure the options consist of Just don't do it (use a nice open standard file format). Not great when someone sends you something. Translate the format on Windows. I think you need Publisher, the viewer won't even print. But you can download a trial version for a once off (been there, done that). Submit the file for online translation to PDF. www.pdfonline.com/convert-pdf/ Use a Windows VM, wine, crossover office, Win4Lin, or otherwise run Publisher "under" linux. What I really want to do is convert it to something nicer natively under Linux.

  Read the article

• nginx url rewriting: difference between break and last

  - by Peter

  I don't understand the difference between break and last (flags of rewrite). The documentation is rather abstruse. I've tried to switch between the two in some of my configs, but I couldn't spot any difference in behavior. Can someone please explain these flags in more detail? Preferably with an example that shows different behavior when flipping one flag to another.

  Read the article

• CentOS 6.3 X86_64 RAM detection

  - by Peter

  I have a machine with 8GB ram (BIOS sees it, so my motherboard and CPU supports it), and I installed CentOS 6.3 on it. When it starts up, it only see 3.1GB. uname says: 2.6.32-279.1.1.el6.x86_64 #1 SMP BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000cf65f000 (usable) BIOS-e820: 00000000cf65f000 - 00000000cf6e8000 (ACPI NVS) BIOS-e820: 00000000cf6e8000 - 00000000cf6ec000 (usable) BIOS-e820: 00000000cf6ec000 - 00000000cf6ff000 (ACPI data) BIOS-e820: 00000000cf6ff000 - 00000000cf700000 (usable) dmesg | grep -i memory says: initial memory mapped : 0 - 20000000 init_memory_mapping: 0000000000000000-00000000cf700000 Reserving 129MB of memory at 48MB for crashkernel (System RAM: 3319MB) PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 PM: Registered nosave memory: 00000000cf65f000 - 00000000cf6e8000 PM: Registered nosave memory: 00000000cf6ec000 - 00000000cf6ff000 Memory: 3184828k/3398656k available (5152k kernel code, 1016k absent, 212812k reserved, 7166k data, 1260k init) please try 'cgroup_disable=memory' option if you don't want memory cgroups Initializing cgroup subsys memory Freeing initrd memory: 16136k freed Non-volatile memory driver v1.3 agpgart-intel 0000:00:00.0: detected 8192K stolen memory crash memory driver: version 1.1 Freeing unused kernel memory: 1260k freed Freeing unused kernel memory: 972k freed Freeing unused kernel memory: 1732k freed Update: Memtest see all the 8GB, and dmidecode -t 17 | grep Size too. But free -m still see only 3.1 GB. Question: How can I repair/modify the system, to see all the 8GB RAM? Thanks in advance!

  Read the article

• Linux-Mint Maya Mate loses Alt-F1 menu and Alt-F2 run-dialog with Compiz

  - by Peter.O

  I like the Linux-Mint 13 Mate Alt-F1 menu and the Alt-F2 run-dialog, but as soon as I installed Compiz those keys became non-functional. Conpiz has a Gnome compaatibility settings panel which allows you to set these keys, but using that Compix settings panel did not make any diference (probably because Mate is not Gnome, strictly speaking)... Is there some way to get those two shortcut keys back into acton with Compiz?

  Read the article

• Kickstart based installation of RHEL 6.4 from USB

  - by Peter

  I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

  Read the article

• Windows application for tracking web pages?

  - by Peter Mortensen

  Can you recommend a stand-alone Windows application (that excludes Firefox plug-ins) for alerting when web pages change their content?

  Read the article

• Wrong PC-projector resolution in Windows 7

  - by peter.olsson

  I'm connecting a PC-projector (Benq MP721) to a Windows 7 Professional laptop (HP 6730b). All the output settings on the laptop, including the laptop screen, changes to 1024x768 (which the projector supports). However the projector says it receives 1360x768 and asks me to change the resolution to 1024x768. I'm using mirrored display. The laptop is 1024x768 The screen resolution in the control panel says 1024x768 The Intel graphics card utilities says 1024x768 The driver for the projector is a Generic PnP Monitor Is there anything in Windows 7 that would convert my 4:3 resolution to wide screen automatically?

  Read the article

• How can I run Gnome or KDE locally in Cygwin?

  - by John Peter Thompson Garcés

  Apparently it is possible to do this using cygwin ports, as can be seen in screenshots. I followed this how-to to get apt-cygports set up, and I used it to install gnome-session. This how-to supposedly gives the commands needed to run Gnome or KDE, but whenever I try to run Gnome, a blank X-window pops up and then quickly disappears. Here is the terminal output: $ startx /usr/bin/dbus-launch gnome-session xauth: file /home/jpthomps/.serverauth.4168 does not exist Welcome to the XWin X Server Vendor: The Cygwin/X Project Release: 1.10.3.0 OS: Windows 7 Service Pack 1 [Windows NT 6.1 build 7601] (WoW64) Package: version 1.10.3-12 built 2011-08-22 XWin was started with the following command line: /usr/bin/X :0 -auth /home/jpthomps/.serverauth.4168 (II) xorg.conf is not supported (II) See http://x.cygwin.com/docs/faq/cygwin-x-faq.html for more information LoadPreferences: /home/jpthomps/.XWinrc not found LoadPreferences: Loading /etc/X11/system.XWinrc LoadPreferences: Done parsing the configuration file... winDetectSupportedEngines - DirectDraw installed, allowing ShadowDD winDetectSupportedEngines - Windows NT, allowing PrimaryDD winDetectSupportedEngines - DirectDraw4 installed, allowing ShadowDDNL winDetectSupportedEngines - Returning, supported engines 0000001f winSetEngine - Using Shadow DirectDraw NonLocking winScreenInit - Using Windows display depth of 32 bits per pixel winFinishScreenInitFB - Masks: 00ff0000 0000ff00 000000ff Screen 0 added at virtual desktop coordinate (0,0). MIT-SHM extension disabled due to lack of kernel support XFree86-Bigfont extension local-client optimization disabled due to lack of shared memory support in the kernel (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 winPointerWarpCursor - Discarding first warp: 637 478 (--) 5 mouse buttons found (--) Setting autorepeat to delay=500, rate=31 (--) Windows keyboard layout: "00000409" (00000409) "US", type 4 (--) Found matching XKB configuration "English (USA)" (--) Model = "pc105" Layout = "us" Variant = "none" Options = "none" Rules = "base" Model = "pc105" Layout = "us" Variant = "none" Options = "none" winBlockHandler - pthread_mutex_unlock() winProcEstablishConnection - winInitClipboard returned. winClipboardProc - DISPLAY=:0.0 winClipboardProc - XOpenDisplay () returned and successfully opened the display. xinit: XFree86_VT property unexpectedly has 0 items instead of 1 xinit: connection to X server lost waiting for X server to shut down winClipboardProc - winClipboardFlushWindowsMessageQueue trapped WM_QUIT message, exiting main loop. winClipboardProc - XDestroyWindow succeeded. winClipboardProc - Clipboard disabled - Exit from server winDeinitMultiWindowWM - Noting shutdown in progress

  Read the article

• Cannot Access a Shared Folder Using Windows 2008

  - by peter

  Hi All, I have a NAS drive, and this is sharing some folders. I cannot access those folders from a windows 2008 machine which is on the network. The are both connected to the same network switch. e.g. if I go like this, \\server\ or \\server\folder I get the message 'windows cannot access \\server check the spelling, click diagnose' etc. Error code: 0x80004005 The thing is that I can connect to this shared drive from a windows 7 laptop connected wirelessly to the same network. I can ping the server from windows 2008, but only if I use the IP address, not the server name.

  Read the article

• mdadm raid5 recover double disk failure - with a twist (drive order)

  - by Peter Bos

  Let me acknowledge first off that I have made mistakes, and that I have a backup for most but not all of the data on this RAID. I still have hope of recovering the rest of the data. I don't have the kind of money to take the drives to a recovery expert company. Mistake #0, not having a 100% backup. I know. I have a mdadm RAID5 system of 4x3TB. Drives /dev/sd[b-e], all with one partition /dev/sd[b-e]1. I'm aware that RAID5 on very large drives is risky, yet I did it anyway. Recent events The RAID become degraded after a two drive failure. One drive [/dev/sdc] is really gone, the other [/dev/sde] came back up after a power cycle, but was not automatically re-added to the RAID. So I was left with a 4 device RAID with only 2 active drives [/dev/sdb and /dev/sdd]. Mistake #1, not using dd copies of the drives for restoring the RAID. I did not have the drives or the time. Mistake #2, not making a backup of the superblock and mdadm -E of the remaining drives. Recovery attempt I reassembled the RAID in degraded mode with mdadm --assemble --force /dev/md0, using /dev/sd[bde]1. I could then access my data. I replaced /dev/sdc with a spare; empty; identical drive. I removed the old /dev/sdc1 from the RAID mdadm --fail /dev/md0 /dev/sdc1 Mistake #3, not doing this before replacing the drive I then partitioned the new /dev/sdc and added it to the RAID. mdadm --add /dev/md0 /dev/sdc1 It then began to restore the RAID. ETA 300 mins. I followed the process via /proc/mdstat to 2% and then went to do other stuff. Checking the result Several hours (but less then 300 mins) later, I checked the process. It had stopped due to a read error on /dev/sde1. Here is where the trouble really starts I then removed /dev/sde1 from the RAID and re-added it. I can't remember why I did this; it was late. mdadm --manage /dev/md0 --remove /dev/sde1 mdadm --manage /dev/md0 --add /dev/sde1 However, /dev/sde1 was now marked as spare. So I decided to recreate the whole array using --assume-clean using what I thought was the right order, and with /dev/sdc1 missing. mdadm --create /dev/md0 --assume-clean -l5 -n4 /dev/sdb1 missing /dev/sdd1 /dev/sde1 That worked, but the filesystem was not recognized while trying to mount. (It should have been EXT4). Device order I then checked a recent backup I had of /proc/mdstat, and I found the drive order. md0 : active raid5 sdb1[0] sde1[4] sdd1[2] sdc1[1] 8790402048 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] I then remembered this RAID had suffered a drive loss about a year ago, and recovered from it by replacing the faulty drive with a spare one. That may have scrambled the device order a bit...so there was no drive [3] but only [0],[1],[2], and [4]. I tried to find the drive order with the Permute_array script: https://raid.wiki.kernel.org/index.php/Permute_array.pl but that did not find the right order. Questions I now have two main questions: I screwed up all the superblocks on the drives, but only gave: mdadm --create --assume-clean commands (so I should not have overwritten the data itself on /dev/sd[bde]1. Am I right that in theory the RAID can be restored [assuming for a moment that /dev/sde1 is ok] if I just find the right device order? Is it important that /dev/sde1 be given the device number [4] in the RAID? When I create it with mdadm --create /dev/md0 --assume-clean -l5 -n4 \ /dev/sdb1 missing /dev/sdd1 /dev/sde1 it is assigned the number [3]. I wonder if that is relevant to the calculation of the parity blocks. If it turns out to be important, how can I recreate the array with /dev/sdb1[0] missing[1] /dev/sdd1[2] /dev/sde1[4]? If I could get that to work I could start it in degraded mode and add the new drive /dev/sdc1 and let it resync again. It's OK if you would like to point out to me that this may not have been the best course of action, but you'll find that I realized this. It would be great if anyone has any suggestions.

  Read the article

• Vantec NexStar NAS Enclosures - Writing large files

  - by peter

  I have one of these 'Vantec NexStar LX - NST-475LX-BK' drive enclosures. It is a NAS device. When I write a file to the device using eSata, or a SMB share I cannot write files over 4GB. I think this is because the drive is formatted with FAT32. But when I access the device using FTP it doesn't matter. I can write files of any size. E.g. I wrote one on there last night which was 30GB. Does this make any sense? Why? I guess the most important thing for me is data integrity.

  Read the article

• Why is IIS7 not compressing my static files?

  - by Peter Evjan

  I am trying to get IIS to compress jquery.js (and all other static files, but using jquery as the example here) on my localhost, but something goes wrong. The funny part is that when I look in my %SystemDrive%\inetpub\temp\IIS Temporary Compressed Files\MySiteName, I see the jquery.js file there, and its size is 24 KB. But in the browser, according to the Net tab on Firebug, the size is 69 kb. I've tried the following: - Checked that my browser accept compression. I found "Accept-Encoding gzip, deflate" in the request header via Firebug - Enabling Failed Request Tracing. Nothing turns up in the %SystemDrive%\inetpub\logs\FailedReqLogFiles folder after I do my request though.

  Read the article

• VMware and Windows Activation

  - by Peter M

  Yesterday I installed Slysoft's Virtual CloneDrive in order to mount an iso for some software installation on my host system (XP Pro SP3) This morning I fired up VMware and made a linked clone of an existing XP vm in order to do some software testing. This is the sort of thing that I do all the time, and the base XP vm that I clone was activated a long long time ago. The surprise today was that the newly cloned vm was no longer activated and XP cited major changes in hardware as the reason. I repeated the test with a full clone of the base system and got the same message. I then started up my base vm and it seemed to be activated, yet another vm (which I fully cloned from the base vm a long time ago) now started reporting that XP was not activated. At this point I guessed that Virtual DriveClone might have been the source of my hardware differences so I uninstalled it and rebooted. After this I made a new linked clone and full clone of the base vm and XP did not complain about not being activated. So I seem to be back to where I was before installing Virtual DriveClone with the exception that that one particular XP vm continues to complain about activation (even though 4 or 5 other XP vm's are fat and happy) Now to my questions: Why would adding Virtual CloneDrive to the host system affect XP activation on the vm's? From their point of view I would have thought that the environment had not changed as I had not enabled any new hard drives in their systems. Or is adding a hard drive to the host system enough to upset XP activation? Since this event, one of my fully cloned vm's is still reporting that XP is not activated even though I have removed Virtual CloneDrive. Is there anyway to convince XP that it is on the same system as yesterday? Or are my only options to do an activation or restore the vm from a previous backup?

  Read the article

• Buffer Overflow errors when reading ConfigDelay and Manufacturer info from registry

  - by peter

  Hi All, This is a strange driver error which doesn't make a lot of sense to me. I am running an application developed in C# .NET which our company develops. I was monitoring the application using process monitor and noticed that it accesses the registry a lot. The output on Process Monitor looks like this, Operation Result Path RegQueryValue Success HKLM\System\CurrentControlSet\Enum\SWMUXBUS\SW_MODEM\7&6c4af30&0&5&0004\Driver RegQueryValue Success HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\Properties RegQueryValue Success HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\Default RegQueryValue Success HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\InactivityScale RegQueryValue Name Not Found HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\PowerDelay RegQueryValue Name Not Found HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\ConfigDelay RegQueryValue Buffer Overflow HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\Manufacturer RegQueryValue Buffer Overflow HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\Model RegQueryValue Name Not Found HKLM\System\CurrentControlSet\Control\Class\{4D36E96D-E325-11CE-BFC1-08002BE10318}\0000\Version The app is reading this stuff every 5 seconds from the registry, so I would ask a few questions, 1) What is this stuff 2) Why is the app reading this stuff 3) Why is it saying 'Buffer Overflow' 4) Could this cause performance problems for my app? From what I can see the app does not explicitly read this stuff, so I think this relates to a driver on the machine (which is a netbook)

  Read the article

• Loss of feature set with VMware EVC

  - by Peter

  If I have two machines both 3rd Generation AMD Opteron, one Shanghai & one Istanbul and I can vMotion between them. Does it buy me anything to enable EVC at the 3rd Generation AMD level? Will I lose any CPU features? My thoughts are, I can enable EVC 3rd Generation with running VMs and I can't enable 2nd Generation EVC with running VMs. I figure there won't be a lose in any features because if there was a reduction in feature set then I couldn't enable EVC with running VMs.

  Read the article

• How to set up that specific domains are tunneled to another server

  - by Peter Smit

  I am working at an university as research assistant. Often I would like to connect from home to university resources over http or ssh, but they are blocked from outside access. Therefore, they have a front-end ssh server where we can ssh into and from there to other hosts. For http access they advise to set up an ssh tunnel like this ssh -L 1234:proxyserver.university.fi:8080 publicsshserver.university.fi and put the proxy settings of your browser to point to port 1234 All nice and working, but I would not like to let all my other internet traffic go over this proxy server, and everytime I want to connect to the university I have to do this steps again. What would I like: - Set up a ssh tunnel everytime I log in my computer. I have a certificate, so no passwords are needed - Have a way to redirect some wildcard-domains always through the ssh-server first. So that when I type intra.university.fi in my browser, transparently the request is going through the tunnel. Same when I want to ssh into another resource within the university Is this possible? For the http part I think I maybe should set up my own local transparent proxy to have this easily done. How about the ssh part?

  Read the article

• Baseline upload speed for streaming video on demand?

  - by Peter Turner

  Is there a table that shows what is necessary for streaming video on demand? Specifically what I'm trying to do is stream Video on Demand to 50-100 people. I'm flexible with the format, but I'd like text on the screen to be legible (i.e. not 320x240). If someone knows of a calculator or something that would let me figure out exactly how I need to structure my video and ISP that'd be handy too.

  Read the article

• 7-Zip on multi-core computers

  - by Peter Mortensen

  Does 7-Zip take advantage of multiprocessor or multi-core systems? For example, would there be a close to 16 times speed-up on a 16 core system assuming no disk or memory bottlenecks? Or is it is limited to 2 threads (2 times speed-up on systems with more than one CPU or core)?

  Read the article

• multi-user rvm gem install failure when called from CloudFormation::Init

  - by Peter Mounce

  I've taken an Amazon Linux AMI (based on CentOS) and installed RVM (1.10.3) to it in multi-user fashion (see {1} below). I used that to install ruby 1.9.3-p125, rubygems 1.8.17, and bundler 1.1 as the baseline requirements for most things I'm going to be using the instances for. I've captured that instance to an AMI, and am now launching it via CloudFormation, with some CloudFormation::Init commands. One of them is to use s3cmd to pull down a private gem from S3, and the next one, the one that fails, is to install that gem. It fails with an error message 2012-03-15 16:53:20,201 [ERROR] Command 20_install_gems (/usr/local/rvm/rubies/ruby-1.9.3-p125/bin/gem install ./*.gem) failed 2012-03-15 16:53:20,202 [DEBUG] Command 20_install_gems output: /usr/local/rvm/rubies/ruby-1.9.3-p125/bin/gem:12:in `require': no such file to load -- rubygems (LoadError) from /usr/local/rvm/rubies/ruby-1.9.3-p125/bin/gem:12 Now, that happens during the cfn-init execution - I assume, but haven't checked yet, that cfn-init is being run with an environment different from that of ec2-user (there are no other users on the instance). If I run gem install mygem.gem in an interactive session then that works fine. So, my question really, is what should I do to make this work for cfn-init? Have I correctly set up rvm as multi-user? I've confirmed that cfn-init is being run as the root user, with his restricted environment. How should I source the /etc/profile.d/rvm.sh into root's sessions? {1} My semi-automated rvm installation steps (run in interactive session as ec2-user): sudo bash -s stable < <(curl -s https://raw.github.com/wayneeseguin/rvm/master/binscripts/rvm-installer ) sudo gpasswd -a ec2-user rvm # iconv-devel is baked into centos' glibc sudo yum install -y autoconf automake bison bzip2 gcc-c++ git libffi-devel libtool libxml2-devel libxslt-devel libyaml-devel make openssl-devel patch readline readline-devel zlib zlib-devel source /etc/profile.d/rvm.sh rvm list known # in a new session: rvm install ruby-1.9.3-p125 rvm use 1.9.3 --default gem update --system # gems required by public_web-awareness gem install aws-sdk bundler cocaine sinatra echo -e "gem: --no-ri --no-rdoc\n" > /home/ec2-user/.gemrc # delete unnecessary documentation files rm -rf `gem env gemdir`/doc sudo -s sudo echo -e "gem: --no-ri --no-rdoc\n" > /etc/skel/.gemrc sudo echo -e "gem: --no-ri --no-rdoc\n" > /etc/gemrc # ctrl + d out of the sudo session Some environment information: [ec2-user@ip ~]$ echo $PATH /usr/local/rvm/gems/ruby-1.9.3-p125/bin:/usr/local/rvm/gems/ruby-1.9.3-p125@global/bin:/usr/local/rvm/rubies/ruby-1.9.3-p125/bin:/usr/local/rvm/bin:/usr/local/bin:/bin:/usr/bin:/usr/local/sbin:/usr/sbin:/sbin:/opt/aws/bin:/home/ec2-user/bin [ec2-user@ip ~]$ echo $GEM_HOME /usr/local/rvm/gems/ruby-1.9.3-p125 [ec2-user@ip ~]$ echo $GEM_PATH /usr/local/rvm/gems/ruby-1.9.3-p125:/usr/local/rvm/gems/ruby-1.9.3-p125@global [ec2-user@ip ~]$ echo $BUNDLE_PATH [ec2-user@ip ~]$ gem list *** LOCAL GEMS *** aws-sdk (1.3.6) bundler (1.1.0) cocaine (0.2.1) httparty (0.8.1) json (1.6.5) multi_json (1.1.0) multi_xml (0.4.1) nokogiri (1.5.1, 1.5.0) rack (1.4.1) rack-protection (1.2.0) rake (0.9.2) sinatra (1.3.2) tilt (1.3.3) uuidtools (2.1.2) yamler (0.1.0)

  Read the article

• Problem with single quotes in man pages

  - by Peter

  When I ssh into my Debian Lenny server and open a man page, single quotes appear to be messed up. Example from the man page of apt-get: If no package matches the given expression and the expression contains one of ´.´, ´?´ or ´*´ then it is assumed to be a POSIX regular expression, and it is applied to all package names in the database. Any matches are then installed (or removed). Note that matching is done by substring so ´lo.*´ matches ´how-lo´ and ´lowest´. If this is undesired, anchor the regular expression with a ´^´ or ´$´ character, or create a more specific regular expression. I'm on Mac OS X and using xterm. If I use Terminal, the problem doesn't happen. My locale is configured correctly as far as I can see: $ locale LANG=en_US.UTF-8 LC_CTYPE="en_US.UTF-8" LC_NUMERIC="en_US.UTF-8" LC_TIME="en_US.UTF-8" LC_COLLATE="en_US.UTF-8" LC_MONETARY="en_US.UTF-8" LC_MESSAGES="en_US.UTF-8" LC_PAPER="en_US.UTF-8" LC_NAME="en_US.UTF-8" LC_ADDRESS="en_US.UTF-8" LC_TELEPHONE="en_US.UTF-8" LC_MEASUREMENT="en_US.UTF-8" LC_IDENTIFICATION="en_US.UTF-8" LC_ALL= I'm not sure what's wrong with my environment, and I have no idea what to check next. I'd appreciate help.

  Read the article

• How do I get classic page search back for Opera 10.5?

  - by Peter Mortensen

  I have upgraded to Opera 10.51 (from Opera 9.64). How do I get search in a page (Ctrl + F) to use a dialog box (as in 9.64) instead of the modal jumping around? (I have to press Esc in order to be able navigate with the arrow keys again and this clears the highlight of a match).

  Read the article

• Is it easy to update ubuntu beta to ubuntu final release?

  - by Peter Smit

  At this moment I am preparing a virtual server to host a web application which needs php5.3 The virtual server base image is always Hardy (8.04 LTS). There is no php5.3 until the upcoming release in a few days: Lucid (9.04 LTS). I am seeing to options: - waiting until the final version is released and then start preparing this server - Now upgrading to the beta (do-release-upgrade --devel-release) and when the final release has come upgrading to that For time constraints I would prefer the second option. I only can't find whether it will be easy to upgrade from a beta to the 'clean' final release. Is this possible in an easy way. Will it have any drawback for security or will there be any traces left of it being ever a beta release? Note: the server will not go into production before the LTS is really installed.

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >