Search Results

Search found 5845 results on 234 pages for 'commit protocol'.

Page 171/234 | < Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >

• Problems with ipsec betwen Cisco ASA 5505 and Juniper ssg5

  - by Oskar Kjellin

  I am trying to set up an ipsec tunnel between our ASA 5505 and a Juniper ssg5. The tunnel is up and running, but I cannot get any data through it. The local network I am on is 172.16.1.0 and the remote is 192.168.70.0. But I cannot ping anything on their netowork. I receive a "Phase 2 OK" when I set up the ipsec. I think this is the part of the config that is applicable. It seems like the data is not routed through the tunnel, but I am not sure... object network our-network subnet 172.16.1.0 255.255.255.0 object network their-network subnet 192.168.70.0 255.255.255.0 access-list outside_cryptomap extended permit ip object our-network object their-network crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer THEIR_IP crypto map outside_map 1 set ikev1 phase1-mode aggressive crypto map outside_map 1 set ikev1 transform-set ESP-3DES-MD5 crypto map outside_map 1 set ikev2 pre-shared-key ***** crypto map outside_map 1 set reverse-route crypto map outside_map interface outside webvpn group-policy GroupPolicy_THEIR_IP internal group-policy GroupPolicy_THEIR_IP attributes vpn-filter value outside_cryptomap ipv6-vpn-filter none vpn-tunnel-protocol ikev1 tunnel-group THEIR_IP type ipsec-l2l tunnel-group THEIR_IP general-attributes default-group-policy GroupPolicy_THEIR_IP tunnel-group THEIR_IP ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key *****

  Read the article

• Apache HTTPD - Segmentation fault when loading mod_jk module

  - by Hans Engel

  I just set up mod_jk with my Apache httpd 2.0.52 installation, but now when I try to start Apache, it has a segmentation fault. I've checked that I am using the mod_jk compiled for 2.0.x.. built against the same version I have, in fact. I've also verified that the path I'm giving to LoadModule is correct, and the permissions and the ownership of the file are the same as the rest of the modules'. When I remove the "LoadModule" command for mod_jk from my httpd.conf, there is no segmentation fault. Nothing shows in Apache's error logs. I have tried restarting the server with this module using both service httpd restart and httpd. These are the last few lines returned of strace httpd -X: gettimeofday({1292100295, 434487}, NULL) = 0 socket(PF_INET6, SOCK_STREAM, IPPROTO_IP) = -1 EAFNOSUPPORT (Address family not supported by protocol) socket(PF_NETLINK, SOCK_RAW, 0) = 3 bind(3, {sa_family=AF_NETLINK, pid=0, groups=00000000}, 12) = 0 getsockname(3, {sa_family=AF_NETLINK, pid=22378, groups=00000000}, [12]) = 0 time(NULL) = 1292100295 sendto(3, "\24\0\0\0\26\0\1\3\307\342\3M\0\0\0\0\0\305\333\267", 20, 0, {sa_family=AF_NETLINK, pid=0, groups=00000000}, 12) = 20 recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"<\0\0\0\24\0\2\0\307\342\3MjW\0\0\2\10\200\376\1\0\0\0"..., 4096}], msg_controllen=0, msg_flags=0}, 0) = 664 recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\24\0\0\0\3\0\2\0\307\342\3MjW\0\0\0\0\0\0\1\0\0\0\10\0"..., 4096}], msg_controllen=0, msg_flags=0}, 0) = 20 close(3) = 0 socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 3 --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV +++ Process 22378 detached Has anyone had a similar problem using Apache 2.0.52 with mod_jk? I might try downloading and building the source for the Apache server and mod_jk myself if there isn't a discovered fix for this.

  Read the article

• LDAP not showing secondary groups

  - by Sandy Dolphinaura

  Currently, I have a LDAP server (running ClearOS if that makes any difference) containing a database of users. So, I went and setup LDAP on a couple of my debian VMs, using libpam-ldapd and I discovered this odd problem. My group/user mapping would show up when running getent group but the secondary groups would not show up when running id . Here is my /etc/nslcd.conf # /etc/nslcd.conf # nslcd configuration file. See nslcd.conf(5) # for details. # The user and group nslcd should run as. uid nslcd gid nslcd # The location at which the LDAP server(s) should be reachable. uri ldaps://10.3.0.1 # The search base that will be used for all queries. base dc=pnet,dc=sandyd,dc=me # The LDAP protocol version to use. #ldap_version 3 # The DN to bind with for normal lookups. binddn cn=manager,ou=internal,dc=pnet,dc=sandyd,dc=me bindpw Me29Dakyoz8Wn2zI # The DN used for password modifications by root. #rootpwmoddn cn=admin,dc=example,dc=com # SSL options ssl on tls_reqcert never # The search scope. #scope sub #filter group (&(objectClass=group)(gidNumber=*)) map group uniqueMember member

  Read the article

• exim configuration: 503 AUTH command used when not advertised

  - by jrdioko

  I'm running a piece of software on a Windows server that sends email notifications via a remote SMTP server. It has very few configuration options, and only supports basic SMTP authentication without SSL/TLS. I have exim4 running on a Debian server that will be the SMTP server for this Windows program. It is set up with default configuration, plus allowing AUTH PLAIN and AUTH LOGIN unencrypted connections. I have successfully sent an email over telnet: telnet servername 25 ehlo test 250-AUTH PLAIN LOGIN ... auth plain XXX 235 Authentication succeeded mail from: ... ... However, the program I want to connect to this server fails to connect. To see why, I ran a packet sniffer during the connection, and see the following session: C: HELO hostname S: 250 Hello hostname C: AUTH LOGIN XXX | XXX S: 503 AUTH command used when not advertised | 500 unrecognized command C: QUIT S: 221 closing connection I'm not familiar enough with the SMTP protocol to understand what's going on here. What do I need to change on my exim4 SMTP server to allow for this connection to be made?

  Read the article

• How to mount vfat drive on Linux with ownership other than root?

  - by Norman Ramsey

  I'm running into trouble mounting an iPod on a newly upgraded Debian Squeeze. I suspect either a protocol has changed or I've tickled a bug, which I don't know where to report. I'm trying to mount the iPod so that I have permission to read and write it. But my efforts come to nothing: $ sudo mount -v -t vfat -o uid=32074,gid=6202 /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control $ sudo umount /mnt $ sudo mount -v -t vfat -o uid=nr,gid=nr /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control As you see, I've tried both symbolic and numberic IDs, but the files persist in being owned by root (and only writable by root). The IDs are really mine; I've had the UID since 1993. $ id uid=32074(nr) gid=6202(nr) groups=6202(nr),0(root),2(bin),4(adm),... I've put an strace at http://pastebin.com/Xue2u9FZ, and the mount(2) call looks good: mount("/dev/sde2", "/mnt", "vfat", MS_MGC_VAL, "uid=32074,gid=6202") = 0 Finally, here's my kernel version from uname -a: Linux homedog 2.6.32-5-686 #1 SMP Mon Jun 13 04:13:06 UTC 2011 i686 GNU/Linux Does anyone know if I should be doing something different, or If there is a workaround, or If this is a bug, where it should be reported?

  Read the article

• running red5 on port 80

  - by ArneLovius

  I have a red5 application http://code.google.com/p/openmeetings that runs under red5, and is accessible on port 5080 and 8443 I've installed it on Ubuntu 10.04 The eventual aim is to have it accessible via https on 443 instead of 8443, but I thought I would initially try on 80 so that any issues were just down to the port configuration and not SSL certificates. I've tried changing the port from 5080 to 80 in the red5.properties file, but it fails to start. In the red5.log I have seen ERROR o.a.coyote.http11.Http11Protocol - Error initializing endpoint java.net.BindException: Permission denied /0.0.0.0:80 In the error.log I have seen ERROR o.a.coyote.http11.Http11Protocol - Error initializing endpoint java.net.BindException: Permission denied /0.0.0.0:80 and ERROR org.red5.server.tomcat.TomcatLoader - Error loading tomcat, unable to bind connector. You may not have permission to use the selected port org.apache.catalina.LifecycleException: Protocol handler initialization failed: java.net.BindException: Permission denied /0.0.0.0:80 There is nothing else installed or running on port 80, so I presume that this is a "needs to be root" situation. I would rather not run an Internet accessible web service as root. I know that Tomcat can run on port 80 by changing “#AUTHBIND=no” to “AUTHBIND=yes” in /etc/default/tomcat6 but I have not been able to find anything similar for red5. Am I on a hiding to nothing, or is there better way than running as root ? Thanks!

  Read the article

• Amazon EC2 Reserved Instances: "Heavy Utilization" clarification

  - by gravyface

  Should be another easy one here, but I need clarification on what they define as "heavy utilization" for Reserved Instance types. From their Website: Heavy Utilization RIs – Heavy Utilization RIs offer the most absolute savings of any Reserved Instance type. They’re most appropriate for steady-state workloads where you’re willing to commit to always running these instances in exchange for our lowest hourly usage fee. With this RI, you pay a little higher upfront payment than Medium Utilization RIs, a significantly lower hourly usage fee, and you’re charged that lower hourly rate for every hour in the Reserved Instance term you purchase. Using Heavy Utilization RIs, you can save up to 41% for a 1-year term and 58% for a 3-year term vs. running On-Demand Instances. If you’re trying to find a break-even utilization, you’re economically advantaged using Heavy Utilization RIs (vs. On-Demand Instances) if you plan to use your instance more than 43% of a 1-year term or 79% of a 3-year term. I'm assuming that, if I'm planning on running a 24/7 Web Server, then regardless of how many resources I consume (bandwidth, cpu cycles, memory), I would want to go with a Heavy Utilization Reserved Instance? This one Web Server in particular will likely barely budge the cpu, but it needs to be up and running 24/7. Not 100% on what they're defining as "heavy".

  Read the article

• Troubleshooting iptables and configuring it to drop the priority of long-term connections

  - by intuited

  I'm somewhat familiar with the general concepts of iptables, and would like to learn it in more detail. I'm hoping that my learning experience can also be useful. The situation: I'm running dd-wrt on my router. Despite its purported QoS skills, I'm still seeing connection latency shoot up hugely whenever there's an ongoing http connection, eg some large download. Under such conditions, it can take 10 seconds or more to load a basic webpage; sometimes the connections are dropped entirely. I've tried adjusting the parameters, dropping the allotted bandwidth for up and download to well under my limit, but nothing seems to work. dd-wrt is configured to use HTB as the QoS algorithm; HFSC, although presented as an option, seems to cause the router to crash, and is rumoured to not actually work on any linux system. I'd like to be able to troubleshoot this issue and hopefully improve the settings that dd-wrt is using, but I'm finding the learning curve a bit overwhelming. For starters I am not sure what HTB actually specifies: is this a set of iptables commands, or do some of those commands specify how HTB is to be used? I would like it to prioritize based on protocol the way that it already supposed to, and in addition I'd like to have it drop the priority of connections which have a high total byte count, say over 400KB. Also tips on utilities that can be run under dd-wrt to get more info on what's going on in there are appreciated. I've tried to get iftop to work but there were issues running curses. I'm leaning towards replacing dd-wrt with openwrt; comments on this strategy are also welcome. I suspect that I would be well advised to get a second router as a standin before trying that. It may be worth noting that my total bandwidth is pretty limited (256Kbit/s).

  Read the article

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• Can an image based backup potentially corrupt data?

  - by ServerAdminGuy45

  I'm considering doing image based backups (Acronis) on production Windows systems during non-peak hours. I'm just wondering if they can potentially lead to application data corruption. Lets say that I have a database that is getting hit pretty hard. Could I potentially have the beginning blocks of the database be commit ed to the image, data inserted into the db (which changes the beginning blocks of the DB on the server but not the image), then the blocks of data committed to the image (leading to an inconsistent state). Here's an example of what I'm trying to illustrate. Imagine a simple data structure which has a number in the front which represents the number of "a"s in a file. The number and data are delimited by a "-". For example: 4-ajjjjjjjajuuuuuuuaoffffa If an "a" is changed, the datastructure resets the number in the begining of the file such as: 3-ajjjjjjjajuuuuuuuboffffa I assume acronis writes block by block being a straight up image so here is what i'm invisioning happening with my database t0: 4-ajjjjjjjajuuuuuuuaoffffa ^pointer is here t1: 4-ajjjjjjjajuuuuuuuaoffffa ^pointer is here (all data before this is comitted to the image) t2: 4-ajjjjjjjajuuuuuuuboffffa ^pointer is here (all data before this is comitted to the image) Also notice how one of the "a"s change to a b. There are only 3 "a"s now t3: 4-ajjjjjjjajuuuuuuuboffffa ^pointer is here (all data before this is comitted to the image) The final image now reads "4-ajjjjjjjajuuuuuuuboffffa", while the true data is "3-ajjjjjjjajuuuuuuuboffffa" leading to a corrupt "database". Basically changes further down the blockchain could be reflected in the image, while important header and synchronization could already be committed. The out of date header information doesn't accurately reflect the structure of the blocks to come.

  Read the article

• VPN on OSX disconnects after precisely 2 minutes and 30 seconds on specific network

  - by Tyilo

  When connecting to my own VPN server on a specific network, called public-network, my Mac disconnects the VPN connection after 2 minutes and 30 seconds. I have performed several tests and this is the result: It works fine until the 2:30 mark It doesn't matter which Mac I use, it still disconnects It doesn't matter which client I use, all of the following does the same: OSX system client, HMA! Pro VPN and Shimo It doesn't matter which protocol I use, at least all of these protocols does the same: PPTP, OpenVPN and L2TP over IPSec The same thing happens using my own VPN server and HMA!'s VPN server. All other clients (Windows/iPhone) can use any of these VPN servers and protocols without problem on public-network On OSX, all the protocols, clients and servers works fine on any other network So it seems that it is the combination of OSX, VPN & public-network that causes this. This is the syslog from my VPN server, when the disconnection happens: Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: EOF or bad error reading ctrl packet length. Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: couldn't read packet header (exit) Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: CTRL read failed Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: Reaping child PPP[31401] Feb 2 12:04:32 raspberrypi pppd[31401]: Hangup (SIGHUP) Feb 2 12:04:32 raspberrypi pppd[31401]: Modem hangup Feb 2 12:04:32 raspberrypi pppd[31401]: Connect time 2.5 minutes. Feb 2 12:04:32 raspberrypi pppd[31401]: Sent 3963649 bytes, received 362775 bytes. Feb 2 12:04:32 raspberrypi pppd[31401]: MPPE disabled Feb 2 12:04:32 raspberrypi pppd[31401]: Connection terminated. Feb 2 12:04:32 raspberrypi pppd[31401]: Exit. Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: Client <ip-adress> control connection finished

  Read the article

• mod_jk problem: Tomcat is probably not started or is listening on the wrong port

  - by Konrad

  Hi, I am running some application on Tomcat 6.0.26. There is Apache in front of web server talking to it over mod_jk. Every few hours when I try to access application browser simply spins, and no content is retrieved. No error is reported in Tomcat logs, but I fond such errors in mod_jk log: [Sun Jul 04 21:19:13 2010][error] ajp_service::jk_ajp_common.c (1758): Error connecting to tomcat. Tomcat is probably not started or is listening on the wrong port. worker=***** failed [Sun Jul 04 21:19:13 2010][info] jk_handler::mod_jk.c (1985): Service error=0 for worker==***** [Sun Jul 04 21:19:13 2010][info] ajp_connection_tcp_get_message::jk_ajp_common.c (955): Tomcat has forced a connection close for socket 46 [Sun Jul 04 21:19:13 2010][info] ajp_connection_tcp_get_message::jk_ajp_common.c (955): Tomcat has forced a connection close for socket 46 [Sun Jul 04 21:19:13 2010][info] ajp_connection_tcp_get_message::jk_ajp_common.c (955): Tomcat has forced a connection close for socket 46 [Sun Jul 04 21:19:13 2010][error] ajp_get_reply::jk_ajp_common.c (1503): Tomcat is down or refused connection. No response has been sent to the client (yet) [Sun Jul 04 21:19:13 2010][error] ajp_get_reply::jk_ajp_common.c (1503): Tomcat is down or refused connection. No response has been sent to the client (yet) [Sun Jul 04 21:19:13 2010][info] ajp_connection_tcp_get_message::jk_ajp_common.c (955): Tomcat has forced a connection close for socket 46 [Sun Jul 04 21:19:13 2010][error] ajp_get_reply::jk_ajp_common.c (1503): Tomcat is down or refused connection. No response has been sent to the client (yet) [Sun Jul 04 21:19:13 2010][info] ajp_connection_tcp_get_message::jk_ajp_common.c (955): Tomcat has forced a connection close for socket 45 [Sun Jul 04 21:19:13 2010][info] ajp_connection_tcp_get_message::jk_ajp_common.c (955): Tomcat has forced a connection close for socket 46 [Sun Jul 04 21:19:13 2010][info] ajp_service::jk_ajp_common.c (1721): Receiving from tomcat failed, recoverable operation attempt=0 my worker is configured in following way: worker.admanagonode.port=8009 worker.admanagonode.host=*****.com worker.admanagonode.type=ajp13 worker.admanagonode.ping_mode=A worker.admanagonode.socket_timeout=60 worker.admanagonode.prepost_timeout=10000 worker.admanagonode.connect_timeout=10000 worker.admanagonode.connection_pool_size=200 worker.admanagonode.connection_pool_timeout=300 worker.admanagonode.retries=20 worker.admanagonode.socket_keepalive=1 worker.admanagonode.cachesize=10 worker.admanagonode.cache_timeout=600 Tomcat has same port number in Connector configuration: <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" address="*********" /> Does any of you has any ideas what i am missing? What can cause such problems? Cheers Konrad

  Read the article

• apache-user & root access

  - by ahmedshaikhm

  I want to develop few scripts in php that will invoke following commands; using exec() function service network restart crontab -u root /xyz/abc/fjs/crontab etc. The issue is that Apache executes script as apache user (I am on CentOS 5), regardless of adding apache into wheel or doing good, the bad and the ugly group assignment does not run commands (as mentioned above). Following are my configurations; My /etc/sudoers root ALL=(ALL) ALL apache ALL=(ALL) NOPASSWD: ALL %wheel ALL=(ALL) ALL %wheel ALL=(ALL) NOPASSWD: ALL As I've tried couple of combination with sudoer & httpd.conf, the recent httpd.conf look something as follows; my httpd.conf User apache Group wheel my PHP script exec("service network start", $a); print_r($a); exec("sudo -u root service network start", $a); print_r($a); Output Array ( [0] => Bringing up loopback interface: [FAILED] [1] => Bringing up interface eth0: [FAILED] [2] => Bringing up interface eth0_1: [FAILED] [3] => Bringing up interface eth1: [FAILED] ) Array ( [0] => Bringing up loopback interface: [FAILED] [1] => Bringing up interface eth0: [FAILED] [2] => Bringing up interface eth0_1: [FAILED] [3] => Bringing up interface eth1: [FAILED] ) Without any surprise, when I invoke restart network services via ssh, using similar user like apache, the command successfully executes. Its all about accessing such commands via HTTP Protocol. I am sure cPanel/Plesk kind of software do use something like sudoer or something and what I am trying to do is basically possible. But I need your help to understand which piece I am missing? Thanks a lot!

  Read the article

• New Windows Server 2008 R2 WIMP running slower than Windows Server 2003

  - by starshine531

  We recently upgraded a WIMP server from Windows Server 2003 (32 bit) to Windows Server 2008 R2 (64 bit). The new server has significantly better hardware than the old server, yet many processes take much longer than the old box. We have a rather complex web application process that normally takes about 7 seconds on the old box, but on the new one it takes 11-12 seconds. That's down from 15.5 seconds it took before I disabled IPV6. This process involves some queries (some of them involve transactions with maybe 3 queries between the start and commit) and creating and emailing some pdfs. Windows updates are current with a more or less fresh machine. This happens consistently even when we have almost no traffic on the site and memory and cpu aren't being hard pressed at all. The only differences between the servers other than the OS and hardware: 1) When available, we used 64 bit versions of programs 2) The new server uses MySQL 5.5 rather than MySQL 5.1 (I did run the mysql_upgrade program and we use InnoDB for the engine) 3) The new server uses PHP Version 5.3.18 rather than PHP Version 5.3.1 4) With the new OS came IIS7 rather than IIS6 of course. What could be causing better hardware to run so much slower? Let me know if you need more details. Thank you.

  Read the article

• Linux group permissions getting overwritten by owner

  - by Andy

  I am not a user of Linux, but I am encountering some permissions problems with it that I hope someone can shed some light on. Bit of background: A colleague of mine has a Linux box (running Debian I believe) with an SVN repository on it. The repository directory and files 'owner' is my colleauge. We are both members of a group called 'users'. He manages several projects both Linux and Windows apps, while I have one Windows app. For the Windows apps, we both use TortoiseSVN via an SSH link to commit/update. Performing the command 'ls -l' shows the repository files and folders on the Linux box to have the following permissions: -rwxrwx--- john users However, when my colleauge commits to the repository, the permissions change to: -rwxrwx--- john john This then means I get 'Permission denied' when trying to access the repository myself as it appears that the group permissions have been overwritten with only 'owner' permissions. To fix this, a 'chown -R' command is applied to the files/folders to set the permissions back to owner/group, but each time he writes to the repository, the issue repeats. I'm not sure if this is solely an SVN problem, or a more fundamental owner/group issue. Anyone any clue on how to stop this happening, or where to go and look? I'm trying to help out my colleague who is having some trouble resolving this issue. Apologies for the vague info, I hope I have conveyed the problem clear enough. Like I say, I am not a Linux user, I have only put down what I have managed to pick up from looking over his shoulder. Thanks for any pointers I can pass on!

  Read the article

• Are HDMI to VGA Adapters Really Device-Specific?

  - by allquixotic

  There are a lot of devices on the market right now (especially mobile devices) with a Micro-HDMI or Mini-HDMI port and no VGA or D-Sub output. Most manufacturers of said devices sell a cable that looks something like this: I have yet to find a cable like this that claims to work on a wide array of devices. In general, these cables claim to work with one specific device only. The way these cables work, I think, is that analog VGA signals are sent from the HDMI port on the device. This should work for devices that have special hardware on the motherboard/GPU capable of driving this. Is it the case that these cables have to be custom designed for each device? Or, is it rather that any device which possesses this special "signaling of analog VGA over the HDMI port" can be made to work with a cable that is physically compatible (i.e. the HDMI end plugs into the device and the VGA end accepts a VGA monitor cable)? Note that I am not looking for a product recommendation, just a conceptual clarification on what exactly these devices are doing. Also, a few remarks: The cables like the one depicted here are not digital to analog converters. I know about these: they are expensive, and they are the ONLY solution if your device only outputs a digital signal and is incapable of driving analog VGA over the HDMI port. The cables like the one depicted here are not straight crossover cables from VGA to HDMI, either. The crossover cables are designed to send a digital HDMI signal over the VGA port's wires; that is, the wire protocol is HDMI (digital) but the physical pinout is the same as VGA, even though nothing analog is happening. Once again, this is not the behavior that, I believe, the devices which I'm talking about in this question are doing. The cabling and devices that this question is about transmit the analog VGA data over the HDMI port (the HDMI port is in the device outputting the data, and the VGA side is the monitor/projector).

  Read the article

• iptables port forwarding works only for localhost

  - by Venki

  Below is my iptables config. I used this for my accessing a node js website running in port 9000 through port 80. This works fine only if access the website through local host / loop back. When I try to use the ip of eth0, which is assigned by my router through dcp. this does not work, when I use ip like 192.168.0.103 to access the website. I am not able to figure what is wrong here, Already burnt a day in this, still not able to figure out :( Edit: ( more information) Earlier, I was using this configuration to develop the website, i had configured the domain name to point to 127.0.0.1 in the /etc/hosts file. It was working fine, but now I am trying to deploy the website in a vps with static ip, This configuration does not work with both static IP. # redirect port 80 to port 9000 *nat :PREROUTING ACCEPT [57:3896] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [4229:289686] :POSTROUTING ACCEPT [4239:290286] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 9000 -A OUTPUT -d 127.0.0.1/32 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 9000 COMMIT # Allow HTTP and HTTPS connections from anywhere (the normal ports for websites and SSL). -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT -A INPUT -p tcp --dport 9000 -j ACCEPT -A INPUT -j REJECT

  Read the article

• rsync over ssh backup failing after relocation of server

  - by OlduvaiHand

  I've got two FreeBSD machines set up; one serves video data and the other is the backup for the first. At this point I've got around 4TB of data. I add files to the video server a few at a time, and was planning to use rsync over ssh to keep the backup machine up to date. I did the initial, large backup with both machines hooked up to the same subnet at the lab with no problems using rsync. Then, when I moved the backup machine off-site (but still on the university network), I attempted a sync without changing anything other than the IP (as the machine is now on a different subnet) and got the following error: 2010/03/22 15:55:21 [1260] rsync: connection unexpectedly closed (6340840244 bytes received so far) [receiver] 2010/03/22 15:55:21 [1260] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [receiver=3.0.7] 2010/03/22 15:55:21 [1258] rsync: connection unexpectedly closed (60 bytes received so far) [generator] 2010/03/22 15:55:21 [1258] rsync error: unexplained error (code 255) at io.c(601) [generator=3.0.7] The script that handles the backup hasn't been changed, nor has the crontab that invokes it. Does anyone have any ideas about what might be causing the hiccup? I was under the impression that it might have something to do with the ssh connection timing out or something along those lines, but am not entirely clear on how to diagnose the cause of the problem.

  Read the article

• Linux Experts Riddle: Network output of 10MB/s on 10GB/s NIC

  - by user150324

  I have two CentOS 6 servers. I am trying to transfer files between them. Source server has 10GB/s NIC nd destination server has 1GB/s NIC. Regardless to the command used nor the protocol, the transfer speed is ~1 Mega byte per second. The goal is at least couple dozens MB per second. I have tried: rsync (also with various encryptions), scp, wget, aftp, nc. Here's some testing results with iperf: [root@serv ~]# iperf -c XXX.XXX.XXX.XXX -i 1 ------------------------------------------------------------ Client connecting to XXX.XXX.XXX.XXX, TCP port 5001 TCP window size: 64.0 KByte (default) ------------------------------------------------------------ [ 3] local XXX.XXX.XXX.XXX port 33180 connected with XXX.XXX.XXX.XXX port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 1.30 MBytes 10.9 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 1.0- 2.0 sec 1.28 MBytes 10.7 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 2.0- 3.0 sec 1.34 MBytes 11.3 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 3.0- 4.0 sec 1.53 MBytes 12.8 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 4.0- 5.0 sec 1.65 MBytes 13.8 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 5.0- 6.0 sec 1.79 MBytes 15.0 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 6.0- 7.0 sec 1.95 MBytes 16.3 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 7.0- 8.0 sec 1.98 MBytes 16.6 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 8.0- 9.0 sec 1.91 MBytes 16.0 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 9.0-10.0 sec 2.05 MBytes 17.2 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.68 MBytes 14.0 Mbits/sec I guess HD is not the bottleneck here.

  Read the article

• Apache 2 proxy for Tomcat 7

  - by hsnm

  Following the how-to, I wanted to make a proxy for traffic to the address /app to be processed by Tomcat 7. I added this to my httpd.conf: LoadModule proxy_module {path-to-modules}/mod_proxy.so LoadModule deflate_module modules/mod_deflate.so ProxyPass /app http://localhost:8081 ProxyPassReverse /app http://localhost:8081 I also have this on my server.xml: <Connector port="8081" enableLookups="false" acceptCount="100" connectionTimeout="20000" proxyName="localhost" proxyPort="80"/> And I have the folder /var/lib/tomcat7/webapps/app with my application files. I restarted both Tomcat 7 and Apache 2 after doing the configurations above. Problem: When navigating to my webpage.com/app, I get the error 500. I consulted apache logs, it says: [warn] proxy: No protocol handler was valid for the URL /app. If you are using a DSO version of mod_proxy, make sure the proxy submodules are included in the configuration using LoadModule. Update: This is running in ubuntu. I resolved this by adding LoadModule proxy_http_module modules/mod_proxy_http.so to my httpd.conf. Now I have another question: How can I make this proxy to work on SSL through port 443?

  Read the article

• Delay NTP Initialisation, Cisco 877W, IOS 12.4(24)T1

  - by Mike Insch

  I have a Cisco 877W which I'm using for my home ADSL connection (and as a refresher in Cisco IOS). I've got a working config in-place with my PPPoA connection coming online correctly, and VLANs and other settings configured as I want them, but I can't crack the NTP configuration. For NTP, I have the following defined ntp server 0.uk.pool.ntp.org source Dialer0 ntp server 1.uk.pool.ntp.org source Dialer0 ntp server 2.uk.pool.ntp.org source Dialer0 ntp server 3.uk.pool.ntp.org source Dialer0 This setup works fine when issued in Global Configuration Mode when the Dialer0 interface (ATM0.1) is up. The configuration fails at startup though: Translating "1.uk.pool.ntp.org"...domain server (208.67.222.222) (208.67.220.220) ntp server 1.uk.pool.ntp.org source Dialer0 ^ % Invalid input detected at "^" marker. This is repeated for the other servers defined. Obviously the DNS lookup for the server(s) fails because the DNS servers cannot be accessed because the external interface is not yet online. Is there a way to delay the NTP configuration until afte the Dialer0 interface is fully initialised? Can the NTP commands be triggered by the Line Protocol on the Dialer0 interface transitioning to the up state? Alternatively, can the NTP commands be delayed for 5 minutes after the router has finished initialising? Any advice, or pointers to useful documentation or examples gratefully received ...

  Read the article

• Is there a small business router that shows bandwidth usage graphs in the admin panel?

  - by Robert Drake

  I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

  Read the article

• Connect to Postgres remotely, open port 5432 for Postgres in iptables

  - by Victor

  I am trying to connect to Postgres remotely but I need to open port 5432 in iptables. My current iptables configuration is as follows: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT What would I have to add in iptables to open the port? I'm trying to install phppgadmin on a different server to access the postgres database. Thank you.

  Read the article

• How can I use two Internet connections in Ubuntu?

  - by Martin

  My goal is to be able to do something like this: curl google.com --interface ppp0 curl google.com --interface p2p2 ppp0 is a DSL connection, and p2p2 is a separate direct Internet connection. Currently I can only get one of these to work at a time. When I enable one, the other one stops working. /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # DSL auto p2p1 iface p2p1 inet manual auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig p2p1 up # line maintained by pppoeconf provider dsl-provider # DIRECT auto p2p2 iface p2p2 inet dhcp ifconfig: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 p2p1 Link encap:Ethernet inet6 addr: fe80::20a:ebff:fe21:99c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p2p2 Link encap:Ethernet inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20a:ebff:fe17:1249/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ppp0 Link encap:Point-to-Point Protocol inet addr:53.193.231.167 P-t-P:53.193.224.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 10.0.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 53.193.224.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 p2p2 By default, only ppp0 works. If I run "route add default gw 192.168.1.1 p2p2" then I can use p2p2 but ppp0 stops working. If I then run "route add default gw 53.193.224.1 ppp0" then I can use ppp0 again but p2p2 stops working. What can I do to be able to use both interfaces selectively?

  Read the article

< Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >