Search Results

Search found 5712 results on 229 pages for 'j random coder'.

Page 174/229 | < Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• How can I remedy the always-on-top window problem?

  - by GateKiller

  Sorry for the vague title but this one is hard to explain so bear with me please. I'm using Windows Vista at work for web development and sometimes when I Click or Alt-Tab to background window, the window will get focus but it will not be brought to the front. In order to bring the window to the front, I have to click on the applications border (when the resize cursor appears) and the window will then jump to the front. I've had this problem for about a year now and it happens at least a dozen times a day, but it doesn't do this all the time - seems random. I hope I have explained the issue fully (and you've understood it) and would appreciate any constructive answers or comments to solve this problem. Example: If I Alt-Tab from Google Chrome to Notepad and this problem randomly occurs, Google Chrome will remain in front of Notepad, however, I will be able to type text into Notepad while the window is behind Google Chrome. Clicking on Notepad's content area will not bring it to the front but clicking it's window border will. Video Exampe http://vimeo.com/19388998 In this video, I clicked from Google Chome to UltraEdit and chrome stayed in font, but as you can see, I can still type in UltraEdit. I'm starting to believe that this could be a bug in Google Chrome so I'll continue to watch if this between other applications.

  Read the article

• jdbc4 CommunicationsException

  - by letronje

  I have a machine running a java app talking to a mysql instance running on the same instance. the app uses jdbc4 drivers from mysql. I keep getting com.mysql.jdbc.exceptions.jdbc4.CommunicationsException at random times. Here is the whole message. Could not open JDBC Connection for transaction; nested exception is com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: The last packet successfully received from the server was25899 milliseconds ago.The last packet sent successfully to the server was 25899 milliseconds ago, which is longer than the server configured value of 'wait_timeout'. You should consider either expiring and/or testing connection validity before use in your application, increasing the server configured values for client timeouts, or using the Connector/J connection property 'autoReconnect=true' to avoid this problem. For mysql, the value of global 'wait_timeout' and 'interactive_timeout' is set to 3600 seconds and 'connect_timeout' is set to 60 secs. the wait timeout value is much higher than the 26 secs(25899 msecs). mentioned in the exception trace. I use dbcp for connection pooling and here is spring bean config for the datasource. <bean id="dataSource" destroy-method="close" class="org.apache.commons.dbcp.BasicDataSource" > <property name="driverClassName" value="com.mysql.jdbc.Driver"/> <property name="url" value="jdbc:mysql://localhost:3306/db"/> <property name="username" value="xxx"/> <property name="password" value="xxx" /> <property name="poolPreparedStatements" value="false" /> <property name="maxActive" value="3" /> <property name="maxIdle" value="3" /> </bean> Any idea why this could be happening? Will using c3p0 solve the problem ?

  Read the article

• Recover badly recorded DVDs

  - by CesarGon

  A few years ago (2003-2005) I bought a Sony USB external DVD recorder for my Dell laptop and I used it to burn a lot of discs. Much later, when I tried to use one of these discs, I realised that I could not read it. The disc behaved as if it was scratched or dirty. I tried on a couple of different DVD drives but got the same effect. Sadly, all the discs that I burnt with that recorder suffer from the same problem. Edit. When I read one of these discs with ImgBurn, I get lots of unrecovered read errors in multiple sectors, even at 1x speed. The sectors that cause read errors seem to be quite random; it's not always the same one. I have no idea what could be wrong with the discs. I doubt that they are scratched or dirty; it would be too much of a coincidence that all the discs that I burnt with that recorder got damaged at the same time. Also, they don't show any physical defects. Is there any way to diagnose what the problem is and, hopefully, recover the contents of the discs? Many thanks.

  Read the article

• Understanding Microsoft Word Formatting Behavior. Does anyone?

  - by deemer

  This isn't a question about how to do something (well, not directly), but rather an inquiry to see if anyone understands why MS Word behaves the way it does with respect to formatting from a design perspective. This is also admittedly a rant about Word. This is a question that has plagued me, well, every time I open a document in Word, and covers a lot of individual topics, so I'll restrict the discussion here to two concrete behaviors that baffle me. 1) Backspacing over whitespace changes the format of preceding text. This seems to most often occur when the preceding text is a header or list number. The strangest thing about this is the new format of the changed text usually doesn't appear anywhere else in the document. 2) Numbered lists count almost at random. I am working on a document today where the list numbers count as follows: 1, 2, 2, 3, 3. The lettering in the sublists go like this 1: a, 2: a, 2: b c d, 3: e f g, 3: a. Clicking on each number or letter highlights the other numbers or letters that Word thinks it is related to, which are scattered around the document pretty heavily. Attempts to renumber the list have so far proven fruitless, as Word seems to maintain these associations through clipboard copies, etc. Why could this even happen?

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  EDIT: I can only mark one answer as the correct one but the actual solution was a combination of two comments (updating the BIOS to A15 AND installing the Sigmatel audio drivers). I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

• To what extent is size a factor in SSD performance?

  - by artif

  To what extent is the size of an SSD a factor in its performance? In my mind, correct me if I'm wrong, a bigger SSD should be, everything else being equal, faster than a smaller one. A bigger SSD would have more erase blocks and thus more leeway for the FTL (flash translation layer) to do garbage collection optimization. Also there would be more time before TRIM became necessary. I see on Wikipedia that it remarks that "The performance of the SSD can scale with the number of parallel NAND flash chips used in the device" so it seems throughput also increases significantly. Also many SSDs contain internal caches of some sort and presumably those caches are larger for correspondingly large SSDs. But supposing this effect exists, I would like a quantitative analysis. Does throughput increase linearly? How much is garbage collection impacted, if at all? Does latency stay the same? And so on. Would the performance of a 8 GB SSD be significantly different from, for example, an 80 GB SSD assuming both used high quality chips, controllers, etc? Are there any resources (webpages, research papers, presentations, books, etc) that discuss correlations between SSD performance (4 KB random write speed, latency, maximum sequential throughput, etc) and size? I realize this does not really sound like a programming question but it is relevant for what I'm working on (using flash for caching hard drive data) which does involve programming. If there is a better place to ask this question, eg a more hardware oriented site, what would that be? Something like the equivalent of stack overflow (or perhaps a forum) for in-depth questions on hardware interfaces, internals, etc would be appreciated.

  Read the article

• Why is my cron daemon is being killed every few minutes?

  - by user113215

  As of about a week ago, my cron daemon refuses to stay running. I'm using Debian 6 x64 on an OpenVZ virtual machine. Running something like pgrep cron shows that the daemon isn't running. I start the service with service cron start or /etc/init.d/cron start and it launches, but it disappears from the running process list after a few minutes (varying anywhere between 1 - 30 minutes before the process is killed again). Using strace -f service cron start, I can see that the process is being killed for some reason: nanosleep({60, 0}, <unfinished ...> +++ killed by SIGKILL +++ There's nothing relevant in /var/log/syslog, /var/log/messages, /var/log/auth.log, or /var/log/kern.log to explain why the the process is dying. The system has at least 800 MB of free memory, and cat /proc/loadavg returns 0.22 0.13 0.04 so resources shouldn't be the issue. With cron running, free -m reports: total used free shared buffers cached Mem: 1024 211 812 0 0 0 -/+ buffers/cache: 211 812 Swap: 0 0 0 I also tried removing and reinstalling the cron package using apt-get. Update: I initially thought the problem was a resource issues. I erased my entire VPS and started from a fresh Debian image. There is now nothing else running on the system, but even from a clean install my cron daemon is still being killed at random. What else should I check? How do I find out what's killing my crond?

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Configuring Vmware virtual machines to run under different IPs and PC specs

  - by Alex

  Right now I'm using a simple VmWare virtual machine with preinstalled Win 7. The IP is assigned automatically (it's the same as main OS IP). Is it possible to create several virtual machines that have different hardware specifications and different IP addresses? Here is what I mean regarding these issues: Specs: Certainly, you can easily change some specifications in the Settings menu (RAM size, HDD size), but what about advanced settings? For example: advanced settings for the Processor: is it AMD (2500+,4000+, etc.. ) or Intel (core 2, Pentium, etc..) Ram - is it Corsair 4 Gb 1333 Mhz or Kingston 2 x 2 Gb 866Mhz or something else? Hdd - Is it Seagate Barracuda 80 gb 5400 Rpm or is it Samsung 500Gb 7200 Rpm or some random SSD? Programs that work under a Virtual Machine shouldn't have a clue if that's a VmWare or not. IPs: Every program that's launched under main OS use the real IP: 93.56.xx.xx All programs that are launched under virtual machine A use IP 1: 74.78.xx.xx All programs that are launched under virtual machine B use IP 2: 84.159.xx.xx I believe that you have to use either VPN or Proxy to solve this problem. The Sum Up: The idea is to create 2-3 independent virtual machines with different hardware specifications and IP addresses. Programs that work under a certain Virtual Machine shouldn't have a clue if that's a VmWare or the real PC. Any ideas/tips or experience regarding configuration will be appreciated!

  Read the article

• What Windows app can sort a huge XML file?

  - by Torben Gundtofte-Bruun

  I have some enormous XML-based configuration files, with 125000 lines in them. The problem is that they are auto-generated by the system I use, and "child" tags are in a random order within their respective parent tag. This means that a diff comparison is impossible. I want to recursively sort all tags within a parent tag by the value in name="". Some parent tags only appear once and don't have a name="" parameter; these should be sorted by the tag name itself. Once the files are sorted like this, they can be compared quite easily using normal tools. We are currently using ExamXML which can match unsorted XML files, but it fails because the files are too big. Is there an application that can do this? (Windows much preferred; Linux only as a last resort) I do not want to dive into development or XSLT jobs. I am thinking that someone must have made a simple sorting tool like this already - I just can't find it using Google. Update: With help from this site, I created a small package that I want to share: XML-Sorter_v0.3.zip Update: Follow-up question here.

  Read the article

• Xen virtual host can reach some sites but not others

  - by Tun H S Lee

  Okay, this is killing me. Debian Squeeze, Xen 4.0, brand new install. No iptables rules whatsoever except for the ones added by the default xen bridge script. Dom0 can reach the entire world, no problems. DomU can receive packets from some hosts, but not from others. For instance, if I ping Host A, it works fine. If I ping Host B, the DomU reports 100% packet loss. The hosts are random, but consistent (even after reboots). I can see no pattern to why some work and others don't. In fact, in some cases, different virtual hosts on the same server (an other server at a different data center) are divided; some work and others do not. I can reboot (DomU or Dom0 too) and the same hosts will work or fail as before. If I tcpdump on the Host B while pinging from the DomU, everything looks fine. It sees the echo request coming in and says it's sending one back. However, if I tcpdump peth0 on the Dom0, it never sees the echo reply. Any ideas what could be happening? I'm tearing my hair out here.

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• DSL Connection drops

  - by user60024

  Ok, I just moved so I had to switch from Cable to DSL. I know very little about computers or internet connections and such, so I had AT&T come out to the new house to set up their highest speed. When they got here, they told me that I needed to downgrade to 3.5mbps because I was too far away. Well we did and everything was going great for two days until I started experiencing random disconnects which have been happening now for about 2 to 3 weeks. I am using a N300 Wireless Dual Band ADSL2+ Modem Router and my ethernet cable is hooked directly into my computer from it. I recently started to notice that it disconnects around 5:30 and 8:30, which may be because a lot of people are on their computers(?) and that it works perfectly fine, almost, all the time if I'm not playing a game. During this time, when I try to load up World of Warcraft the Internet light disappears and the DSL light begins blinking. (So maybe it's too much for the modem and it resets?) Other than that it is amazing, but I'd like to try and fix some of these problems. If you need more information, let me know on how to get it for you and what to do. Thanks for the help!

  Read the article

• Some Emails incoming to Outlook 2007 are blank, same emails work fine on webmail, iphone, etc

  - by Funran

  This is a pretty easy problem to describe. Basically users who have just been upgraded to Outlook 2007 (yeah I know 2010 is out), are not receiving SOME emails (from outside our domain, ie hotmail, yahoo). Receiving is not the correct word, these emails come in, along with their attachments, subjects, to/from line, etc. But the body is blank. If the same user goes into their webmail, iphone, blackberry instead, they can read the message fine. It's clear to me that something in Outlook 2007 is not generating the body correctly, so it just strips it. I just don't know WHY. Our mail server was recently upgraded to Exchange 2010, users on 2010 running outlook 2003 are working fine, it's just the random emails for users using 2007. I hope I made that clear enough, thank you for any future help guys. EDIT: I don't see rft, but i swear I've seen it before. Here is the view source on a recent email. <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"><html><head> <meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1"> <meta name="GENERATOR" content="MSHTML 8.00.6001.19120"> <DEFANGED_style_0 <="" style=""> </head> <body bgcolor="#ffffff"> <p><DEFANGED_DIV><font color="#0000ff" size="2" face="Calibri">MS,</font></p><DEFANGED_DIV> <p><DEFANGED_DIV><font color="#0000ff" size="2" face="Calibri">Could you tell me please what the legal descrip &amp; Topo Quad name is for this Monroe P.ID Site?</font></p><DEFANGED_DIV> <p><DEFANGED_DIV><em><font color="#0000ff" size="2" face="Calibri">Thanks, Henry Roye</font></em></p><DEFANGED_DIV></body></html>

  Read the article

• SFTP access without hassle

  - by enobayram

  I'm trying to provide access to a local folder for someone over the internet. After googling around a bit, I've come to the conclusion that SFTP is the safest thing to expose through the firewall to the chaotic and evil world of the Internet. I'm planning to use the openssh-server to this end. Even though I trust that openssh will stop a random attacker, I'm not so sure about the security of my computer once someone is connected through ssh. In particular, even if I don't give that person's user account any privileges whatsoever, he might just be able to "su" to, say, "nobody". And since I was never worried about such things before, I might have given some moderate privileges to nobody at some point (not sudo rights surely!). I would of course value your comments about giving privileges to nobody in the first place, but that's not the point, really. My aim is to give SFTP access to someone in such a sandboxed state that I shouldn't need to worry about such things (at least not more so than I should have done before). Is this really possible? Am I speaking nonsense or worried in vain?

  Read the article

• Redmine does not return the web page

  - by m0skit0

  I migrated a Redmine installation from an Ubuntu machine to a Debian one (both 32-bits), and now for some reason, for some users it doesn't return the page but only a 200 OK message. Here is the flow (from Wireshark): GET /issues/142 HTTP/1.1 Host: debian:3000 User-Agent: Mozilla/5.0 (X11; Ubuntu; Linux i686; rv:17.0) Gecko/20100101 Firefox/17.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate Connection: keep-alive Cookie: _redmine_session=BAh7DCIQX2NzcmZfdG9rZW4iMStIM1RBNTlNelZVUXlUazgrR1pUNGUvNGdEbytUZzRyMVFSUnBvNGhlSDg9Ihd0aW1lbG9nX2luZGV4X3NvcnQiEnNwZW50X29uOmRlc2MiD3Nlc3Npb25faWQiJThiMDk0MzVhOTEzYTI0MzVjOGEzYTRmNDU0NzcwMTAwIgx1c2VyX2lkaQoiFmlzc3Vlc19pbmRleF9zb3J0IgxpZDpkZXNjIg1wZXJfcGFnZWlpIgpxdWVyeXsHOg9wcm9qZWN0X2lkaQc6B2lkaQo%3D--8588c221c0642a12f396239455fb702aec14c9c9; my_wiki_session=f70ae11e1c533c86f0e039d63cf3f69c; my_wikiUserID=1; my_wikiUserName=Yasin Cache-Control: max-age=0 HTTP/1.1 200 OK Connection: Keep-Alive Date: Wed, 12 Dec 2012 16:30:16 GMT Server: WEBrick/1.3.1 (Ruby/1.8.7/2010-08-16) Content-Length: 0 As you can see, I get nothing from the server. This is mostly random because this blank page happens sometimes for some users, and for other users it almost never returns the page... I'm absolutely lost here. Any idea about what can be the cause? Thanks in advance!

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• Symantec Antivirus Corporate -- two problems

  - by Alex C.

  We have a Windows network with a domain and about 50 clients. A few months ago, we installed Symantec Antivirus, Corporate Edition ver. 10.1.8.8000. There are two problems. The larger problem is that the software isn't very good at stopping viruses. In the last month, four different machines have become infected with those viruses that masquerade as antivirus software. Two machines I was able to clean with MalWareBytes. The other two were hopeless, and I had to reinstall Windows. Is there something I can do to make the Symantec product more effective? As far as I can tell, it successfully updates definitions nightly and pushes the definitions to the clients. The smaller problem is that the Symantec client applications sometimes initiate scans at random (and inappropriate) times. One of my co-workers complained to me yesterday that her computer was running very slow. I looked at the scan history and found that Symantec had scanned the computer three times during the past two days, and each time during the workday. No threats were found. Not sure why it's doing this, but I'd like it to stop. Any help would be appreciated. Thanks.

  Read the article

• Ubuntu on VPS becomes unresponsive: BUG: soft lockup - CPU#0 stuck for 22s

  - by Bhante Nandiya

  We have a VPS running Ubuntu, on Xen. The problem is this, about once a day, for about 20-50 minutes, at a random time, the server becomes completely unresponsive to the outside world. After this period, it becomes responsive again, as if nothing had happened, it doesn't lose uptime, it doesn't restart. It just starts responding again as if it had been in suspended animation. These outages occur under conditions of non-exceptional memory and cpu, for example 70% mem, 5% cpu. I have stopped all non-essential services so the usage is very even. These outages don't particularly occur during times of increased memory/cpu (during daily tasks), they sometimes occur at times of very low cpu use (<2%), but in the past also occured during swapping. These blackouts have been occurring both under Ubuntu 12.04 LTS, and Ubuntu 14.04 LTS - no change at all (I upgraded Ubuntu specifically to see if it helped this problem). It is possible to log into our webhosts site, and use their administration console to see error messages from during this time. Presumably, these messages are from the Xen virtualization, the main message goes like this: BUG: soft lockp - CPU#0 stuck for 22s! [ksoftireqd/0:3] (repeats many times) SysRq : Emergency Sync (Sometimes this is the only message in the console) Others seen previously under different load situations include: BUG: soft lockup - CPU#0 stuck for 22s! [swapper/0:0] (repeated many times) or: INFO: rcu_sched detected stall on CPU 0 (t=15000 jiffies) (repeated many times with t getting bigger) From googling around I've tried various kernel parameters such as nohz=off and acpi=off to no avail. All tech support has said is that other Ubuntu installations are not suffering the same problem. Anyone got any ideas or experience with this problem?

  Read the article

• Are there any tools to migrate your files, applications, and settings to a new Windows computer?

  - by calbar

  I've decided to upgrade my laptop on a regular basis and one of my main concerns is recreating my entire Windows 7 environment every time I do this. I'm talking toolbar positions, login settings, start menu items, applications and all their customizations... everything but my drivers. It literally takes weeks to fully recreate my working environment, not to mention the risk of user error or just simply forgetting "how I liked it." I'm assuming I won't find something as painless as Apple's Migration Assistant for Windows, but maybe there's something out there that can at least package up your apps and their settings? Bonus points if you can point it to your personal files, too - whatever's the quickest way to get from one machine to the next. I intend to install Windows fresh to remove bloatware on every machine that I buy, then selectively install the drivers I need. Something that accommodates loading my old apps into this newly prepared environment would be ideal. One random point of concern is in regard to application settings that refer to old hardware. I'm not sure if there's anything that can be done about this. If you have any thoughts, feel free to share. Thanks for your help!

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• Cisco configuration for public library internet

  - by AlternateZ

  I'm a C/C++ computer programmer turned IT support guy working for a public library. My day is usually spent helping random grandparents learn how to use email, so my networking knowledge is limited to what I can glean from google. Here's the situation. We have a public library with 20 PCs on a LAN and also public wifi access. Previously we were running all of this on 1 ADSL connection and people complained about low speeds. We hired a networking company to set up a Cisco dual-WAN router for us, and purchased an additional ADSL connection. The intention was to give the LAN PCs a guaranteed amount of bandwidth each, and then let the wifi users split the rest. The results were far worse than what we expected, and all we got from the company was excuses and they've since washed their hands of us. During busy periods, net performance on the LAN PCs are so poor that attaching files to gmail etc often times out and fails - far from the "guaranteed amount of bandwidth each" that we hope for! Sometimes it feels like performance is worse than before when we had 1 ADSL link and an unconfigured router? Anyways, surely this is a problem encountered a million times over across the world? (Sharing internet across many users effectively.) What are standard solutions for something like this? I admit to not even knowing the right jargon to google for (load balancing?) I'd appreciate any links to resources/guides that might help me get a better understanding of the problem/solutions, and perhaps some stories of your own experience in solving similar problems. This will help us evaluate and negotiate with network consultants in the future. If its relevant, our router config contains a section "policy-map" with "bandwidth percent" for each class of user (LAN, wifi), and "fair queue".

  Read the article

• NGINX returning 404 error on a valid url

  - by Harrison

  We have a site that runs PHP-FPM and NGINX. The application sends invitations to site members that are keyed with 40 character random strings (alphanumerics only -- example below). Today for the first time we ran into an issue with this approach. The following url: http://oursite.com/notices/response/approve/1960/OzH0pedV3rJhefFlMezDuoOQSomlUVdhJUliAhjS is returning a 404 error. This url format has been working for 6 months now without an issue, and other urls following this exact format continue to resolve properly. We have a very basic config with a simple redirect to a front controller, and everything else has been running fine for a while now. Also, if we change the last character from an "S" to anything other than a lower-case "s", no 404 error and the site handles the request properly, so I'm wondering if there's some security module that might see something wrong with this specific string... Not sure if that makes any sense. We are not sure where to look to find out what specifically is causing the issue, so any direction would be greatly appreciated. Thanks! Update: Adding a slash to the end of the url allowed it to be handled properly... Would still like to get to the bottom of the issue though. Solved: The problem was caused by part of my configuration... Realized I should have posted, but was headed out of town and didn't have a chance. Any url that ended in say "css" or "js" and not necessarily preceded by a dot (so, for example, http://site.com/response/somerandomestringcss ) was interpreted as a request for a file and the request was not routed through the front controller. The problem was my regex for disabling logging and setting expiration headers on jpgs, gifs, icos, etc. I replaced this: location ~* ^.+(jpg|jpeg|gif|css|png|js|ico)$ { with this: location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { And now urls ending in css, js, png, etc, are properly routed through the front controller. Hopefully that helps someone else out.

  Read the article

< Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >