Search Results

Search found 8552 results on 343 pages for '14 04'.

Page 175/343 | < Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >

  • HDD bad sectors with OS

    - by Michael Z
    I wonder is that possible for OS to make bad sectors on Hard Drive? Preface: I have bought new HDD on 1Tb WB Caviar Black. I have installed new OS on ext4 partition Ubuntu 12.04.1 LTS. After few days S.M.A.R.T. of the Ubuntu's Disk Utility show that my hard has bad sectors! I have checked on S.M.A.R.T. immediately after installing OS - all was OK. During new OS working I have noticed some strange with HDD - all OS was freezed from 20 sec to 1 min and I have heard like HDD's engine restarting. At the dmes I have found something like this: [40085.407947] ata1.00: device reported invalid CHS sector 0

    Read the article

  • Lustre - issues with simple setup

    - by ethrbunny
    Issue: I'm trying to assess the (possible) use of Lustre for our group. To this end I've been trying to create a simple system to explore the nuances. I can't seem to get past the 'llmount.sh' test with any degree of success. What I've done: Each system (throwaway PCs with 70Gb HD, 2Gb RAM) is formatted with CentOS 6.2. I then update everything and install the Lustre kernel from downloads.whamcloud.com and add on the various (appropriate) lustre and e2fs RPM files. Systems are rebooted and tested with 'llmount.sh' (and then cleared with 'llmountcleanup.sh'). All is well to this point. First I create an MDS/MDT system via: /usr/sbin/mkfs.lustre --mgs --mdt --fsname=lustre --device-size=200000 --param sys.timeout=20 --mountfsoptions=errors=remount-ro,user_xattr,acl --param lov.stripesize=1048576 --param lov.stripecount=0 --param mdt.identity_upcall=/usr/sbin/l_getidentity --backfstype ldiskfs --reformat /tmp/lustre-mdt1 and then mkdir -p /mnt/mds1 mount -t lustre -o loop,user_xattr,acl /tmp/lustre-mdt1 /mnt/mds1 Next I take 3 systems and create a 2Gb loop mount via: /usr/sbin/mkfs.lustre --ost --fsname=lustre --device-size=200000 --param sys.timeout=20 --mgsnode=lustre_MDS0@tcp --backfstype ldiskfs --reformat /tmp/lustre-ost1 mkdir -p /mnt/ost1 mount -t lustre -o loop /tmp/lustre-ost1 /mnt/ost1 The logs on the MDT box show the OSS boxes connecting up. All appears ok. Last I create a client and attach to the MDT box: mkdir -p /mnt/lustre mount -t lustre -o user_xattr,acl,flock luster_MDS0@tcp:/lustre /mnt/lustre Again, the log on the MDT box shows the client connection. Appears to be successful. Here's where the issues (appear to) start. If I do a 'df -h' on the client it hangs after showing the system drives. If I attempt to create files (via 'dd') on the lustre mount the session hangs and the job can't be killed. Rebooting the client is the only solution. If I do a 'lctl dl' from the client it shows that only 2/3 OST boxes are found and 'UP'. [root@lfsclient0 etc]# lctl dl 0 UP mgc MGC10.127.24.42@tcp 282d249f-fcb2-b90f-8c4e-2f1415485410 5 1 UP lov lustre-clilov-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 2 UP lmv lustre-clilmv-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 3 UP mdc lustre-MDT0000-mdc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 4 UP osc lustre-OST0000-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 5 UP osc lustre-OST0003-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 Doing a 'lfs df' from the client shows: [root@lfsclient0 etc]# lfs df UUID 1K-blocks Used Available Use% Mounted on lustre-MDT0000_UUID 149944 16900 123044 12% /mnt/lustre[MDT:0] OST0000 : inactive device OST0001 : Resource temporarily unavailable OST0002 : Resource temporarily unavailable lustre-OST0003_UUID 187464 24764 152636 14% /mnt/lustre[OST:3] filesystem summary: 187464 24764 152636 14% /mnt/lustre Given that each OSS box has a 2Gb (loop) mount I would expect to see this reflected in available size. There are no errors on the MDS/MDT box to indicate that multiple OSS/OST boxes have been lost. EDIT: each system has all other systems defined in /etc/hosts and entries in iptables to provide access. SO: I'm clearly making several mistakes. Any pointers as to where to start correcting them?

    Read the article

  • Clone a 2TB WD Green internal drive with bad sectors to a 3TB partitioned external

    - by ron
    I have a 2TB WD Black drive and would like to simply do a straight clone from a failing 3TB drive to it. Both are SATA. Will I be able to just install the new drive alongside the faulty one and then do the clone/rescue attempt with ddrescue or is there a better method? The faulty internal drive mentioned has bed sectors although am usually able to boot into Windows 7 Ultimate with it and navigate and access all my programs. I have been attempting some trials with an Ubuntu Live CD using ddrescue but am not sure I'm doing it right. I have a 3TB WD my book essential external which is GPT and have created a separate 2TB partition on it which I am trying to clone to. I assume I need to format the new drive first to NTFS? Can I do that via the Ubuntu Rescue Remix 12-04 live DVD that I've been booting with?

    Read the article

  • ioncube not load after upgrading to php 5.4

    - by amir
    i am afraid that i broke somthing in my vps :/ i hope you can help me. i am on ubuntu-12.04-x86. and i moved to new vps so i tryied to upgrade the php to the news version from 5.3 to 5.4. anyway after installing i get this messages: fild loading /usr/lib/php5/20090626+lfs/ioncube_loader_lin_5.3.so /usr/php5/20090625+lfs/ioncube_loader_lin_5.3.so: undefined synbol: php_body_wri php 5.4.8-1~presise+1 (cli) (built(oct 29 2012) i need to mention that the server is working and php also working but when i do phpinfo there is no "with the ionCube PHP Loader v4.0.14, Copyright (c) 2002-2011, by ionCube Ltd." which was before :/ i installed with this guide:http://www.upubuntu.com/2012/03/how-to-upgrade-install-php-540-under.html i need to worry?

    Read the article

  • Very High Network out in ec2 instance

    - by Jatin
    I launched an ubuntu-14.04-64bit instance in Amazon EC2 two days back. And I started Tomcat 7.0.54 in that instance and deployed my application war files. It has no other software installed other than tomcat and the default ones. In the past 2 days, its shows 858 GB of Data Transfer(Network Out) from that instance. I have attached a graph of Amazon CloudWatch Metric "Network Out" My application does not do any data download/upload. Its a Java Spring application and the front end is in HTML&Javascript. My application traffic was very low (less than 20 hits) in those 2 days. Is there a way to find out why these data transfers happened and also to find what data has been transferred. If you can see in graph, network out was 20gb per minute. Some more info: Network in was negligible CPU Utilization was very high Everything else was low

    Read the article

  • AWStats log format for tomcat access logs which has X-Forwarded-For

    - by Nix
    What should be the AWStats log format for below tomcat access logs ? I tried these formats but the external IP addresses are not coming into AWStats reports. LogFormat="%host %other %logname %time1 %methodurl %code %bytesd %refererquot %uaquot %referer %other %other" LogFormat="%other %other %logname %time1 %methodurl %code %bytesd %refererquot %uaquot %host_proxy" tomcat valve settings: pattern="%h %l %{USER_ID}s %t &quot;%r&quot; %s %b &quot;%{Referer}i&quot; &quot;%{User-Agent}i&quot; &quot;X-Forwarded-For=%{X-Forwarded-For}i&quot; &quot;JSESSIONID=%{JSESSIONID}c&quot; %D" Log entry: 127.0.0.1 - - [04/Nov/2013:13:39:55 +0000] "GET / HTTP/1.1" 200 12345 "https://www.google.com/url?some_url" "Mozilla/5.0 (Windows NT 6.3; WOW64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/30.0.1599.101 Safari/537.36" "X-Forwarded-For=real_ip, proxy_server_internal_ip" "JSESSIONID=-" 12345

    Read the article

  • Debian is equal to Ubuntu

    - by rkmax
    The title of the question is confusing, and does not explain my point well. I've always used Ubuntu server from version 10.04 and never had problem, now I have 4 machines with ubuntu 12.04.1 LTS installed on them and I found that under any circumstances where there is a high burden throws me a problem and machine crashes constantly. the most common is CPU#X stuck for Ns! Now I wonder if the administration of Debian is equal to that of ubuntu, regarding Servicos, packages, folders structure for example I would like to know if the services are installed in the same manner using invoke-rc.d, which handles additional security, including for not giving blind caning. I've been looking for a comparison chart but have not found anything yet, something between Debian 6.0.6 and Ubuntu 12.04 also the most common "hiccups" when you install the system

    Read the article

  • Mount "Macrium Reflect" on a partition, boot from there?

    - by b e
    Can Macrium's Reflect recovery CD be mounted/used with GRUB ? If the cd can be 'put' (loaded/mounted/...) in a partition, then the only disc needed would be the actual recovery disc, which could be on an external hard drive, or even on the same machine in another partition, thus allowing on to recover using only what's on the machine itself. I have WXPpro and Xubuntu8.04 double mounted, really happy with them together, use each right now to fix problems with the other when they come up. Also have a partition for the Reflect CD, but I just can't get it to load from Grub, which would be great... Thanks for any thoughts, probably someone has already done this I know !

    Read the article

  • Passenger package not found after adding phusion repo Ubuntu 12.04

    - by speshak
    I'm trying to install the official Passenger (and Nginx) packages from Phusion on an Ubuntu 12.04.3 server. I have the following in /etc/apt/sources.list.d/passenger: deb https://oss-binaries.phusionpassenger.com/apt/passenger precise main Even after running apt-get update there is no passenger package found by apt. I did verify that the package info appears in /var/lib/apt/lists/oss-binaries.phusionpassenger.com_apt_passenger_dists_precise_main_binary-amd64_Packages but at this point I'm at a loss as to why the package isn't available via apt-get. There are some packages (libapache2-mod-passenger, passenger-docs) that are available. These packages seem to also exist in universe, but apt-cache show lists both locations.

    Read the article

  • Authentication issues setting up iRedMail on Debian

    - by Sergio Rinaudo
    I'm setting up an exchange server using iRedMail. Following the official iRedMail installation guide (http://www.iredmail.org/install_iredmail_on_debian.html) and the Digital Ocean guide (https://www.digitalocean.com/community/articles/how-to-install-iredmail-on-ubuntu-12-04-x64) I was able to install iRedMail without any problems, so I have all the services up and running. I can configure domains and emails using iRedAdmin BUT I have problem both sending and receiving email, what I get from Roundcube is 'Authentication error' when trying to send an email. Also I can't receive anything. I also tried to connect to the mx server using telnet, it connects, but after the STARTTLS command, when I start to write "MAIL FROM:" the connection is lost. Something in the configuration is not working (at the moment I have the configuration written by the iRedMail installation) but I do not know where, I hope someone can enlight me! Thank you

    Read the article

  • Why standard, virtual host Drupal 7 config causes 403 (Forbidden) in Apache2?

    - by drupality
    Virtual host declaration causing the problem (source): <VirtualHost *:80> ServerAdmin admin@d7 DocumentRoot /vagrant/d7 ServerName www.d7.local ServerAlias d7.local RewriteEngine On RewriteOptions inherit <Directory /vagrant/d7> Order allow,deny Allow from all </Directory> <Directory /vagrant> Order allow,deny Allow from all </Directory> </VirtualHost> error logs: [Mon Nov 04 12:23:11.947082 2013] [authz_core:error] [pid 2471] [client 10.0.2.2:58238] AH01630: client denied by server configuration: /vagrant/d7/ I have no idea why this isn't work... With above rule I have forbidden on drupal site and apache welcome page too (index.html) ls -ld /vagrant/d7 command output: drwxrwxrwx 1 vagrant vagrant 8192 Nov 4 10:05 /vagrant/d7

    Read the article

  • CPanel: Every url is being redirected to http://:2083

    - by Frank
    On my cpanel server, I restored about 50 accounts from crashed cpanel server. All of the sites were working fine, but suddenly without changing anything, every site started to get redirected to url "http://:2083/"., There is nothing in logs, no errors. when i do wget it says: wget grinfeld.com.br --2012-09-04 13:18:23-- http://grinfeld.com.br/ Resolving grinfeld.com.br... 198.101.221.254 Connecting to grinfeld.com.br|198.101.221.254|:80... connected. HTTP request sent, awaiting response... 301 Moved Location: https://:2083/ [following] https://:2083/: Invalid host name.

    Read the article

  • "Cannot allocate memory" while no process seems to be using up memory

    - by omat
    I am not competent on server issues, any help is much appreciated. When try to start a python/django shell on a linux box, I am getting OSError: [Errno 12] Cannot allocate memory. free -m seems to confirm I am out of memory: total used free shared buffers cached Mem: 590 560 29 0 3 37 -/+ buffers/cache: 518 71 Swap: 0 0 0 But I cannot see what is eating up the memory with top or ps aux: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 20 0 24336 908 0 S 0.0 0.2 0:00.68 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0.0 0.0 0:04.85 ksoftirqd/0 How can I identify the leak? Thanks. BTW, I am not sure if it is relevant, but the machine I am talking about is an AWS EC2 instance with Ubuntu 12 running.

    Read the article

  • SSH from Windows Vista to Ubuntu (using cwrsync)

    - by user39141
    Newbie questoin but I can't seem to figure it out. Using cwrsync which in turn calls ssh.exe from a Windows Vista box to Ubuntu. For below, user in ubuntu is 'linuxuser' and user on Windows box is 'winuser' - remote box is 'linuxhost' and windows box is 'winhost' Exported keys such that on the remote box /home/linuxuser/.ssh/authorized_keys is correctly populated. Problem is when I launch ssh it tries to write to /home/winuser/.ssh instead of /cygdrive/home/users/winuser/.ssh as below. c:\Program Files (x86)\cwRsync\binssh linuxuser@linuxhost Could not create directory '/home/winuser/.ssh'. The authenticity of host 'linuxhost (192.168.1.105)' can't be establish ed. RSA key fingerprint is 67:10:a9:49:6e:a3:2b:4a:a0:e0:b7:75:76:da:c3:04. Are you sure you want to continue connecting (yes/no)? Host key verification failed.

    Read the article

  • iptables 1.4 and passive FTP on custom port

    - by Cracky
    after the upgrade from debian squeeze to wheezy I've got a problem with passive FTP connection. I could narrow it to be iptables related, as I could connect via FTP w/o problems after adding my IP to the iptables ACCEPT rule. Before the upgrade I was able just to do modprobe nf_conntract_ftp ports=21332 and adding iptables -A THRU -p tcp --dport 21332 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT now..it doesn't help anymore. The INPUT rule is being triggered as I can see in the counter, but the directory listing is the last thing it does. Setting up a passive-port range is the last thing I want to do, I dislike open ports. I also tried the trick with helper mod by adding following rule before the actual rule for 21332 iptables -A THRU -p tcp -i eth0 --dport 21332 -m state --state NEW -m helper --helper ftp-21332 -j ACCEPT but it doesn't help and is even not being triggered according to counter. The rule in the next line (w/o helper) is being triggered.. here some info: # iptables --version iptables v1.4.14 # lsmod |grep nf_ nf_nat_ftp 12460 0 nf_nat 18242 1 nf_nat_ftp nf_conntrack_ftp 12605 1 nf_nat_ftp nf_conntrack_ipv4 14078 32 nf_nat nf_defrag_ipv4 12483 1 nf_conntrack_ipv4 nf_conntrack 52720 7 xt_state,nf_conntrack_ipv4,xt_conntrack,nf_conntrack_ftp,nf_nat,nf_nat_ftp,xt_helper # uname -a Linux loki 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux # iptables-save # Generated by iptables-save v1.4.14 on Sun Jun 30 03:54:28 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :BLACKLIST - [0:0] :LOGDROP - [0:0] :SPAM - [0:0] :THRU - [0:0] :WEB - [0:0] :fail2ban-dovecot-pop3imap - [0:0] :fail2ban-pureftpd - [0:0] :fail2ban-ssh - [0:0] -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -p tcp -m multiport --dports 21,21332 -j fail2ban-pureftpd -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN FIN,SYN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,ACK FIN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags ACK,URG URG -j DROP -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -j BLACKLIST -A INPUT -j THRU -A INPUT -j LOGDROP -A OUTPUT -j ACCEPT -A OUTPUT -s 93.223.38.223/32 -j ACCEPT -A BLACKLIST -s 38.113.165.0/24 -j LOGDROP -A BLACKLIST -s 202.177.216.0/24 -j LOGDROP -A BLACKLIST -s 130.117.190.0/24 -j LOGDROP -A BLACKLIST -s 117.79.92.0/24 -j LOGDROP -A BLACKLIST -s 72.47.228.0/24 -j LOGDROP -A BLACKLIST -s 195.200.70.0/24 -j LOGDROP -A BLACKLIST -s 195.200.71.0/24 -j LOGDROP -A LOGDROP -m limit --limit 5/sec -j LOG --log-prefix drop_packet_ --log-level 7 -A LOGDROP -p tcp -m tcp --dport 25 -m limit --limit 2/sec -j LOG --log-prefix spam_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 80 -m limit --limit 2/sec -j LOG --log-prefix web_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 22 -m limit --limit 2/sec -j LOG --log-prefix ssh_blacklist --log-level 7 -A LOGDROP -j REJECT --reject-with icmp-host-prohibited -A THRU -p icmp -m limit --limit 1/sec -m icmp --icmp-type 8 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 25 -j ACCEPT -A THRU -i eth0 -p udp -m udp --dport 53 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 110 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 143 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 465 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 585 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 993 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 995 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 2008 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 10011 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 21332 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 30033 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-ssh -j RETURN -A fail2ban-ssh -j RETURN COMMIT # Completed on Sun Jun 30 03:54:28 2013 So, as I said, I have no problems with connecting when adding my IP to go through..but that's not a solution as noone except me can connect anymore~ If someone got an idea what the problem is, please help me! Thanks Cracky

    Read the article

  • Weird Apache Access Logs

    - by user38480
    I see repeated requests like these in my Apache Access Logs and they have been eating up all my CPU. I have a normal WordPress installation. All i changed in the Apache Configuration was changing the DocumentRoot from /var/www/html to /var/www for both ssl and the default configuration. Also, the file referenced in the requests(updatedll.jpeg) does not exist on my server and also isn't referenced in the source code served by any page of the web application. Could this be a security threat? What are these actually and what can i do to stop them. I changed the ip address of my server. They still kept coming. Meaning that somebody is actually hitting the domain name and not the ip address. Why does my server send a 301 for these requests? Shouldn't it be sending a 404? Is it because Wordpress is installed in my root directory and the .htaccess file present for Wordpress is sending a 301 redirect? My disk access logs also seem to have high peaks intermittently. But nobody is actually accessing the site. I see no access logs except these below. Also, i see that all the requests seem to be coming from one of the following 5 ip addresses. 201.4.132.43 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/4.0; BTRS103681; GTB7.5; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; InfoPath.2; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; AskTbATU3/5.15.29.67612; BRI/2)" 187.40.241.48 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; GTB7.5; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729)" 186.56.134.132 - - [05/Jun/2014:07:35:10 -0400] "GET /updatedll.jpg HTTP/1.0" 301 428 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322)" 71.223.252.14 - - [05/Jun/2014:07:35:13 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; BTRS31756; GTB7.5; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; .NET4.0C; .NET4.0E; InfoPath.2)" 85.245.229.167 - - [05/Jun/2014:07:35:14 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; Trident/7.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MAAU; .NET4.0C; BRI/2; .NET4.0E; MAAU)"

    Read the article

  • Why isn't VIM storing macros across sessions?

    - by dotancohen
    In VIM 7.3 on Ubuntu Server 12.04.1, VIM forgets macros and registers after closing. I do have set nocompatible in .vimrc and the command :set viminfo? gives this result: viminfo='100,<50,s10,h What might be preventing the macros and registers from being stored across close / open? Note that I am not interested in storing mappings for long term use in .vimrc. Rather, sometimes (such as during refactoring) I need to perform a simple operation on a few files and I find it easier to do in VIM than with Perl. I just need the macros and registers stored across open / close, which I do have working on other servers. Thanks.

    Read the article

  • Dos-based printing from NT to unix/linux.

    - by SHW
    I need help for the below mentioned scenario: A Dot-matrix printer is physically connected to the Linux machine ( e.g. Ubuntu-10.04 , it can be any unix/linux flavour) From this linux machine, when I take a RDP to the Windows NT-4.0 TS, I run the DOS-based application. Now I want to print few pages from this DOS-based application to the Ubuntu's printer, When I am in RDP-Session. When I followed the samba-printing documentation, I am able to print from GUI-based apps like Notepad, MS WORD and so forth; but not able to print from the command prompt of Windows. Any idea how to do this ? [ WINDOWS MACHINE IS STRICTLY NT-4.0 2000 TS ]

    Read the article

  • Server unresponsive, messages shown on console but not in log files

    - by raistlin majere
    I'm using Ubuntu Server 10.04.4, and once in a while the server hangs (once a month) and is totally unresponsive. The tty is flooded with messages like these. The problem is that these messages are not in my log files after reboot. How to log these messages so that I can analyze them later? In the current logs I can't see anything that would tell me why this is happening. I would also appreciate if anybody can tell from those messages what's going on. This server is a guest virtual machine. The host server is also Ubuntu server 10.04 with KVM/QEMU.

    Read the article

  • Logical move of a server to UK, what do I do with the SSL certificates

    - by flyfishr64
    I have been asked to move a rails application from the US to the UK. This involves bringing up the rails stack on Ubuntu 8.04.4; that's completed. I'm stumped with the SSL configuration though. The plan was to bring this server up with the same domain name but temporarily use a subdomain (app2.xxx.com instead of app.xxx.com) during the move and for testing, then rename it to app.xxx.com when we're ready for the cutover (does that make sense?). In the meantime, we need a new cert for the app2 subdomain. So to generate a CSR, I need a server key but do I need a new one, or should I copy the one from the existing production server?

    Read the article

  • Mac OSX DHCP Stopped Working [on hold]

    - by Jesse James Richard
    Tethering a Raspberry PI to a MacBook (Mavericks) via ethernet is proving to be a real pain. This worked for about a day. My MacBook required a rare reboot and once it came back up the Pi won't get an address. I've confirmed it's not a problem with the Pi. It's a problem with the MacBook for sure. It's basically just stopped giving out IPs. I've read as much as I've found about how to fix this friggin' problem, but I've thus far come up blank. Internet sharing Wi-fi Ethernet enabled, and/or Edited /etc/bootpd.plist as described here (http://www.jacquesf.com/2011/04/mac-os-x-dhcp-server/ - this worked initially and now no longer does) Pi connected directly to the router has no problems. My MacBook DHCP server will no longer give out addresses. Any help would be much appreciated.

    Read the article

  • Unable to change IP address for eth0 without restart in Ubuntu

    - by Rodnower
    I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

    Read the article

  • Chef command to create new ec2 instance with second ebs volume attached and mounted instead of the default ephemeral volume?

    - by runamok
    We currently use this command to create a new ec2 instance with chef: knife ec2 server create --node-name=prod-apache-1 --availability-zone us-east-1c --image ami-3d4ff254 --distro ubuntu12.04-gems --groups "default" --ssh-key foo --identity-file ~/.ssh/id_rsa --ssh-user ubuntu --flavor m1.small After this command we then run further chef commands to finish provisioning the server. I was wondering if it would be possible while first setting up the instance I wanted a 100 gb volume created and mounted at /mnt and to have the ephemeral storage mounted at /tmp or /mnt-ephemeral instead. If not what further commands in chef would you advise running? I know how to do this via the aws console and can probably figure out how to do it via the ec2 command line tools but I am knew to chef and a bit overwhelmed.

    Read the article

  • How can I create a bootable DVD iso from a USB drive?

    - by Kiada
    There seems to be a lot of questions / answers about doing the reverse, but not as much info for USB - DVD. Problem I created a bootable USB drive using YUMI. The USB drive is working great, and contains the following: Linux Mint 13 Linux Mint Debian Debian 6 Ubuntu 12.04.1 Fedora 17 A bit of a mix of DVD and Live versions. I have a spindle of DVD+R DL blank DVD's. I would like to create a bootable .iso from this USB drive so I can burn multiple copies of it to pass around to friends! I've created an iso using Folder2ISO, but it coastered my DVD because it wasn't bootable. I don't really want to waste a whole spindle! How would you go about doing such a thing?

    Read the article

  • How to create a new user group and add user to it in Ubuntu 12.04

    - by Omal Lasitha
    My OS is Ubuntu 12.04.1 Desktop version (32bit). I want to create a new group called restricted which allows its users to use Audio devices and Video devices only, and I want to add a user called visitors to that group. By using Users and Groups, I was able to create a new user account called visitors, and a new group called restricted. But I can't figure out how to add those settings to the group restricted, and add the visitors user account to that group. I tried Google-ing, but every search result was about accessing root privileges and all, and I couldn't find answers on this specific topic.

    Read the article

< Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >