Search Results

Search found 5636 results on 226 pages for 'abcs extension'.

Page 175/226 | < Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >

• Can't install MailParse on cpanel server

  - by Tom

  Hi, I've got a linux vps running CentOs 5.5 (cpanel/whm), I've installed MailParse via Module Installers section on whm, and it did install it, the end of setup log: running: make INSTALL_ROOT="/root/tmp/pear-build-root/install-mailparse-2.1.5" install Installing shared extensions: /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions/no-debug-non-zts-20090626/ running: find "/root/tmp/pear-build-root/install-mailparse-2.1.5" | xargs ls -dils 508718 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5 508745 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr 508746 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib 508747 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php 508748 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions 508749 4 drwxr-xr-x 2 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions/no-debug-non-zts-20090626 508744 196 -rwxr-xr-x 1 root root 193502 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so Build process completed successfully Installing '/usr/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so' install ok: channel://pecl.php.net/mailparse-2.1.5 Extension mailparse enabled in php.ini The mailparse.so object is not in /usr/local/lib/php/extensions/no-debug-non-zts-20090626 Now, when i try to use mailparse functions using php i get the following error: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/local/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so' - /usr/local/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so: cannot open shared object file: No such file or directory in Unknown on line 0 What should i do?

  Read the article

• TCP: Address already in use exception - possible causes for client port? NO PORT EXHAUSTION

  - by TomTom

  Hello, stupid problem. I get those from a client connecting to a server. Sadly, the setup is complicated making debugging complex - and we run out of options. The environment: *Client/Server system, both running on the same machine. The client is actually a service doing some database manipulation at specific times. * The cnonection comes from C# going through OleDb to an EasySoft JDBC driver to a custom written JDBC server that then hosts logic in C++. Yeah, compelx - but the third party supplier decided to expose the extension mechanisms for their server through a JDBC interface. Not a lot can be done here ;) The Symptom: At (ir)regular intervals we get a "Address already in use: connect" told from the JDBC driver. They seem to come from one particular service we run. Now, I did read all the stuff about port exhaustion. This is why we have a little tool running now that counts ports and their states every minute. Last time this happened, we had an astonishing 370 ports in use, with the count rising to about 900 AFTER the error. We aleady patched the registry (it is a windows machine) to allow more than the 5000 client ports standard, but even then, we are far far from that limit to start with. Which is why I am asking here. Ayneone an ide what ELSE could cause this? It is a Windows 2003 Server machine, 64 bit. The only other thing I can see that may cause it (but this functionality is supposedly disabled) is Symantec Endpoint Protection that is installed on the server - and being capable of actinc as a firewall, it could possibly intercept network traffic. I dont want to open a can of worms by pointing to Symantec prematurely (if pointing to Symantec can ever be seen as such). So, anyone an idea what else may be the cause? Thanks

  Read the article

• Postfix not working

  - by user1488723

  A while ago I installed the postfix mail server on my ubuntu 10.04 VPS. At the time it was working good but now it's just stopped working. I was trying to enable SASL authentification and somewhere it must have went really wrong. I've studied the postfix main.cf and done everything in an orderly fashion to ensure that it is nothing wrong. I also have Dovecot installed and configured dovecot.conf to run with Postfix. If I try to do telnet localhost 25 while logged in on the server I just get: Connection closed by foreign host. If I try to do telnet mail.example.com 25 "from the outside" I get: telnet: Unable to connect to remote host: No route to host And when I check the server log after the failed attempts I see this: Jun 28 15:49:31 msv postfix/smtpd[11839]: initializing the server-side TLS engine Jun 28 15:49:31 msv postfix/smtpd[11839]: connect from localhost.localdomain[127.0.0.1] Jun 28 15:49:31 msv postfix/smtpd[11839]: warning: SASL: Connect to /var/spool/postfix/private/auth failed: Connection refused Jun 28 15:49:31 msv postfix/smtpd[11839]: fatal: no SASL authentication mechanisms Jun 28 15:49:32 msv postfix/master[11598]: warning: process /usr/lib/postfix/smtpd pid 11839 exit status 1 Jun 28 15:49:32 msv postfix/master[11598]: warning: /usr/lib/postfix/smtpd: bad command startup -- throttling main.cf file looks like this: smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no append_dot_mydomain = no delay_warning_time = 4h myhostname = mail.example.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mydomain = example.com myorigin = $mydomain mydestination = $mydomain relayhost = mynetworks = 127.0.0.1 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all smtpd_use_tls = yes smtpd_tls_loglevel = 2 smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_tls_CAfile = /etc/postfix/ssl/cacert.pem smtpd_sasl_auth_enable = yes smtpd_client_restrictions = permit_sasl_authenticated, permit_mynetworks, reject_unauth_destination smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks smtpd_recipient_restrictions = permit_sasl_authenticated, reject_unauth_destination broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = /var/spool/postfix/private/auth smtpd_sasl_security_options = noanonymous Dovecot.conf file looks like this: protocols = imap imaps disable_plaintext_auth = no log_timestamp = "%b %d %H:%M:%S " ssl = yes ssl_cert_file = /etc/postfix/ssl/smtpd.crt ssl_key_file = /etc/postfix/ssl/smtpd.key mail_location = maildir:~/mail mail_access_groups = mail auth_username_chars = abcdefghijklmnopqrstuvwxyz protocol imap { imap_client_workarounds = delay-newmail tb-extra-mailbox-sep } auth default { mechanisms = plain login passdb pam { } userdb passwd { } socket listen { client { path = /var/spool/postfix/private/auth user = postfix group = postfix mode = 0660 } } }

  Read the article

• Can Safari 5.1 for Mac OS display favicons for bookmarks in the Bookmarks Bar?

  - by Greg R.

  When bookmarking a web site, most contemporary browser will display the site's favicon next to the bookmark, both in the bookmark view and the bookmark toolbar. This is a useful feature. In the bookmark toolbar you can edit the name of the bookmark to be blank, effectively leaving the favicon there as an easily identifiable "button" from which to launch the bookmark. This allows you to make more effective user of the space in the bookmark toolbar. I use this approach effectively in Firefox, Chrome, and IE. For example, here is a portion of my Bookmarks Toolbar from Firefox: However, in Safari, no favicon is ever displayed for bookmarks. In the full bookmark view only a generic globe icon is displayed. In the Bookmark Bar in Safari, no icon at all is displayed. Which means the habit of removing the bookmark name & leaving the favicon is useless. Here's what the same configuration (synced between browsers via Xmarks) looks like in Safari. That blank space is where the favicons should be. The boomark is there -- if you hover over it, the blank space changes color to indicate the presence of a bookmark and a tool tip will with the URL will pop up after about two seconds. However, it's really quite unusable. So. The question: is there an extension, plug-in, or modification of some sort that will enable the display of favicons for bookmarks in Safari (OS X Lion 10.7.3 , Safari version 5.1.3)?

  Read the article

• Enabling CURL on Ubuntu 11.10

  - by Afsheen Khosravian

  I have installed curl: sudo apt-get install curl libcurl3 libcurl3-dev php5-curl and I have updated my php.ini file to include(I also tried .so): extension=php_curl.dll To test if curl is working I created a file called testCurl.php which contains the following: <?php echo ‘<pre>’; var_dump(curl_version()); echo ‘</pre>’; ?> When I navigate to localhost/testCurl.php I get an error: HTTP Error 500 Heres a snippet from the error log: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/php_curl.dll' - /usr/lib/php5/20090626+lfs/php_curl.dll: cannot op$ PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/sqlite.so' - /usr/lib/php5/20090626+lfs/sqlite.so: cannot open sha$ [Sun Dec 25 12:10:17 2011] [notice] Apache/2.2.20 (Ubuntu) PHP/5.3.6-13ubuntu3.3 with Suhosin-Patch configured -- resuming normal operations [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/` Can anyone help me to get curl working? The problem was with the original test code. I used a new test file containing this and curl is now working: <?php ## Test if cURL is working ## ## SCRIPT BY WWW.WEBUNE.COM (please do not remove)## echo '<pre>'; var_dump(curl_version()); echo '</pre>'; ?>

  Read the article

• How can I override mod-php5's .php mapping to php4-cgi per VirtualHost or Directory?

  - by geocoo

  I am running Debian Linux with apache2 and libapache2-mod-php5 5.3.3-7. I have one VirtualHost which requires php4. So I researched and compiled php4-cgi. However, I cannot seem to: Override mod-php5's mapping of .php in that vhost (or even globally, without disabling php completley). Even find where that mapping is made, in hope of disabling it and enabling mod-php5 or php4-cgi per vhost. This is my php4-cgi mapping (Inside the one php4 vhost): ScriptAlias /php4 /usr/local/php4/bin <Directory /usr/local/php4/bin> Options +ExecCGI +FollowSymLinks </Directory> <Directory /www/test> AddHandler php4-cgi-script .php Action php4-cgi-script /php4/php Options +ExecCGI </Directory> This does not work, mod-php5 still runs all .php files in that vhost/directory. If I change the file extension in the AddHandler above from .php to .php4, then .php4 files do run php4-cgi as expected, but I can't change all the files in the app to .php4. I thought maybe I could disable the mod-php5's mapping in my vhost or directory, then do my cgi-config (as above) but many combinations of these in different contexts did not work: RemoveHandler .php RemoveType .php php_flag engine off (this seems to even disable my php4-cgi so that wont work) The only other place I can find any mapping is in /etc/mime.types, but commenting out the relevant lines and restarting apache2 does not affect mod-php5's .php mapping. I have searched as much as I can, it is now a mystery to me. Any help or direction would be greatly appreciated.

  Read the article

• Win7 Credential manager and accessing SQL Server from outside of the domain

  - by David Lively

  My SQL Server is set to use windows authentication. If I am connected to the domain directly from my Win7 Ultimate x64 machine, SQL Management Studio (SSMS) will let me authenticate with Windows authentication. However, if I am connected via the VPN (from a different machine that is not joined to the domain), it won't. If I start SSMS with the following command line: C:\Windows\system32>runas /netonly /user:domainname\username "C:\Program Files (x86)\Microsoft SQL...\ssms.exe" then connecting to the SQL Server (which is in the domain) with Windows Authentication works fine. I'd like to save these credentials so that I don't have to launch SSMS from the command line, or modify the shortcut. I know I can use the SysInternals ShellRunAs extension to do this, but I again have to enter my domain username and password each time, and shift+right-click to see that menu option. The Windows Credential Manager seems designed to solve this problem, and works for network shares. However, it doesn't seem to work for SSMS. Any suggestions? I've tried using the /savecred option with runas to create the necessary credentials, but that appears to be incompatible with the /netonly option. Running the above command line with the addition of /savecred just displays the runas help screen. Grrr. Argh.

  Read the article

• MAMP Pro .xip.io, fixing urls with htaccess

  - by user3540018

  I've got all my websites set up with MAMP Pro. For instance, I got it set up, so when I go to example.com, the browser displays the website that's set up on my iMac. Now, I wanna get MAMP Pro to work so I can view my website on my other computers/devices (which are all hooked up on the same network.) So far all I had to do is check the checkbox "via Xip.io (LAN only)", and now I can view my website on my other computers/devices within my LAN by simply going to example.com.10.0.1.13.xip.io. Problem is, whenever I'm on this other computer/device, when I click on the links, I get 404 error. ie. whenever I go to example.com/news, I get the 404. But when I go to example.com.10.0.1.13.xip.io/news, THEN I get the right page. So in order to solve my problem I need to rewrite the urls. So whenever someone clicks on a link ie. goes straight to example.com/news, he'll go to example.com.10.0.1.13.xip.io/news. I don't want to change all the links in my MySQL file, but I believe I can do it simply with the htaccess file. I've opened the htaccess file and added the last two lines, but it just doesn't work. <IfModule mod_rewrite.c> RewriteEngine On # Send would-be 404 requests to Craft RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/(favicon\.ico|apple-touch-icon.*\.png)$ [NC] RewriteRule (.+) index.php?p=$1 [QSA,L] RewriteCond %{HTTP_HOST} ^example\.com RewriteRule ^(.*)$ http://www.example.com.10.0.1.13.xip.io/$1 [R=permanent,L] </IfModule> Or perhaps I don't need to change the htaccess file, is there something that I could be missing in the MAMP Pro settings, or perhaps a MAMP extension that I need?

  Read the article

• Problem installing SQLite3 RubyGem on Ubuntu

  - by misbehavens

  I am having a problem trying to install the SQLite3 RubyGem. Here's what I'm doing: $ sudo gem install --remote sqlite3-ruby Here's the output: Building native extensions. This could take a while... ERROR: Error installing sqlite3-ruby: ERROR: Failed to build gem native extension. /usr/bin/ruby1.8 extconf.rb checking for fdatasync() in -lrt... yes checking for sqlite3.h... no *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby1.8 --with-sqlite3-dir --without-sqlite3-dir --with-sqlite3-include --without-sqlite3-include=${sqlite3-dir}/include --with-sqlite3-lib --without-sqlite3-lib=${sqlite3-dir}/lib --with-rtlib --without-rtlib Gem files will remain installed in /usr/lib/ruby/gems/1.8/gems/sqlite3-ruby-1.2.5 for inspection. Results logged to /usr/lib/ruby/gems/1.8/gems/sqlite3-ruby-1.2.5/ext/sqlite3_api/gem_make.out

  Read the article

• Cross OS data recover question, USB drive involved.

  - by Moshe

  Here's the story: A MacBook had OS X 10.4 and Windows XP dual booting using rEFIt. Then the Windows partition gets corrupted and it won't boot. Presumably a virus. There were sensitive files there and those were successfully copied to a USB drive and then 10.5 was installed on the hard drive, formatting the drive in the process. The USB drive's contacts cracked and he data is lost from there, unless it can be resoldered. The issues is that there is too much solder there already. So, how can the data in question be recovered? The files were Microsoft Money (not the latest version) files for the Windows version of the program. Right now, only OS X is installed on the MacBook. Is there Mac based program that can recover the Windows data or am I better off trying to resolder the drive? Does anyone know how to best resolder a USB drive more than once, where the first solder is ther, but detached from the silicon? Also, what format (extension) are Microsoft Money files? In need of help!

  Read the article

• Windows Media Center doesn't see my movies

  - by DrJekyll

  I am trying to configure my Windows Media Center (Windows 7 Ultimate). I selected folder with my movies and added it to the library, but when I went to the movies library, it says "There are no items in this library yet - Windows Media Center is searching for media files in the background...". I have all necessary codecs installed, Windows Media Player opens those movies correctly. When I right click on the file - Open with - Windows Media Center it also plays them without any problem. Any ideas why they don't appear in the libraries? Edit: Movies are coded with divx and xvid codecs and they have ".avi" extension. Windows doesn't have problems playing them. I told Media Center where the files are. I even pointed Windows Media Center to a folder with only one .avi file it still couldn't find anything there. (I have given it quiet some time, even though searching in the directory with only one file shouldn't take more than a few seconds.) When I add a folder with a lot of movies, I get a dialog box "You can wait while media is added or select OK to continue using Windows Media Center.".                                                                        At the end it says it added about 90 movies, but when I go to the libraries, it's still empty.

  Read the article

• Joomla SMTP Configuration Issue

  - by msargenttrue

  I'm having an issue with the SMTP setup of my Joomla website when trying to send mass emails through the CB Mailing (Mass Email) extension. I receive this error: SMTP Error! The following recipients failed: Number of users to whom e-mail was sent: 0 (Total in list: 1) The old version of this websites mass emailer worked fine, however, in order to add Kunena Forum and maintain compatibility I had to make several upgrades to the site. Both the new version and old verson configurations are outlined below. Server for Website: Mac OS X Server 10.4.11, Apache 1.3.4.1, PHP 5.2.3, MySQL 4.1.22 Server for SMTP: Eudora Internet Mail Server 3.3.9 (EIMS Server X) New Configuration: Joomla 1.5.25, Community Builder 1.7.1, CB Paid Subscriptions (CB Subs) 1.2.2, CBMailing 2.3.4, Kunena Forum 1.7.0, Legacy 1.0 plug-in disabled Mail Settings (New Config): Mailer: SMTP Server Mail from: [email protected] From Name: CASPA Sendmail Path: /usr/sbin/sendmail SMTP Authentication: Yes SMTP Security: None SMTP Port: 25 SMTP Username: [email protected] SMTP Password: xxxxxxx SMTP Host: 209.48.40.194 Old Configuration (Working SMTP Configuration): Joomla 1.5.9, Community Builder 1.2, CB Paid Subscriptions (CB Subs) 1.0.3, CB Mailing 2.1, Legacy 1.0 plug-in enabled Mail Settings (Old Config): Mailer: SMTP Server Mail from: [email protected] From Name: CASPA Sendmail Path: /usr/sbin/sendmail SMTP Authentication: Yes SMTP Username: [email protected] SMTP Password: xxxxxxx SMTP Host: 209.48.40.194 (Notice how the older version of Joomla is missing the 2 fields: SMTP Security and SMTP Port) Thanks in advance!

  Read the article

• SSD seems dead after wakeup from Windows Sleep, BIOS stalls but doesn't find it anymore

  - by Abel

  The morning, the following scary scenario happened: I woke up my Windows system Typed in my username and got an error (something like "could not load security xxx", but unsure of exact wording) System auto-restarted after cliking OK It didn't boot up anymore to the SSD with Windows 7 OS (I have another disk I can boot to, but that doesn't see the disk either). Obviously, this happened right after I instantiated a backup procedure, which hasn't succeeded either. The BIOS can't find the drive when I connect to SATA. And it can't find the drive when I connect it to SAS. I have a Dell Workstation T7400, most recent BIOS (version A06), version of SAS Host Bus Adapter BIOS (HBA) is MPTBIOS 6.14.10.00 (2007.09.29) from LSI Logic Corp. Other findings: When connecting to SATA, the DELL Logo screen stays really long (5 minutes) and then at the end of POST it says that a drive is not found When connecting to SAS, the SAS HBA initializing phase takes long (2 minutes, against normally 15 seconds) When running Dell Diagnostics, it doesn't finish and gives the error Exception occurred in module MPCACHE.MDM file "IOAPICSP.ASM" line 1645. I contacted Dell. On their advice I tried different slots and different cables to no avail. I use an APIC battery power, spikes in the power are thus unlikely. My conclusion so far: the disk is dead. I need this disk very badly because it contains the last few days of important development of which not all code was checked in the moment this happened. Are there any ways to recover dead SSD drives? The drive is a new X25-M G2 160GB model SSDSA2M160G2GC 2.5" in an extension bay and has been running without issues for 3 months on SAS.

  Read the article

• How do I correctly SSH port forward using LiveReload on Redhat?

  - by program247365

  Referencing this page: http://feedback.livereload.com/knowledgebase/articles/86280-if-you-edit-files-directly-on-your-server It says you can remotely port forward the LiveReload specific port of 35729, using this command: ssh -L 35729:127.0.0.1:35729 mylogin@myremoteserverIP When I run the -v option, I get: debug1: Local connections to LOCALHOST:35729 forwarded to remote address 127.0.0.1:35729 debug1: Local forwarding listening on ::1 port 35729. debug1: channel 0: new [port listener] debug1: Local forwarding listening on 127.0.0.1 port 35729. debug1: channel 1: new [port listener] debug1: channel 2: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: client_input_channel_req: channel 2 rtype [email protected] reply 1 debug1: Connection to port 35729 forwarding to 127.0.0.1 port 35729 requested. debug1: channel 3: new [direct-tcpip] channel 3: open failed: connect failed: Connection refused debug1: channel 3: free: direct-tcpip: listening port 35729 for 127.0.0.1 port 35729, connect from 127.0.0.1 port 63673, nchannels 4 I thought editing my /etc/services with this line, would work, but it doesn't: livereload 35729/tcp # livereload usage with guard-livereload Every time I attempt to connect with the browser extension, I believe It's getting blocked by my server. What am I missing here? Do I need to edit /etc/services for this to work?

  Read the article

• .NET not processing an XML file in IIS

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at. If I suffix the page .aspx, of course it works fine.

  Read the article

• Strange activity in My Pictures folder: Thumbnail doesn't match actual picture.

  - by Sam152

  After finding an amusing picture on a popular imageboard, I decided to save it. A few days past and I was browsing my images folder when I realised that the thumbnail generated by Windows XP in the thumbnails view did not match the actual image. Here is a comparison image: What's even stranger in this situation is that the parts of the photograph that are different have actually been replaced with what might be the correct background. Furthermore, it is a jpeg (no PNG transparency tricks) that is 343 kilobytes but only 847x847 pixels wide. What could be going on here? Could there be anything malicious in the works, or hidden data? Before anyone asks, I have checked and preformed the following: Deleted Thumbs.db to reload thumbnails. Opened image in different editors. (they appear with the text) Moved image to a different directory. Changed the extension to .rar. All these steps produce the same results. Pre actual posting update: It seems that opening the image in paint, changing the image entirely (deleting entire contents and making a red fill) will still generate the original thumbnail, even after deleting Thumbs.db etc. I'm also hesitant to post the original data, in case there is something malicious or hidden that could be potentially illegal. (Although it would be very beneficial to see if it works on other computers and not just my own).

  Read the article

• Not able to run firefox in a head-less Ubuntu server 9.10

  - by Julio J.

  I need to run Firefox in my server in order to execute some Selenium tests from Hudson. I would love no to have to install a complete gui. So I installed Xvfb in order to fake the Gui (I understand it this way correct me if my assumptions are wrong). After some time trying to make it work, I'm stuck with the next situation: $ sudo Xvfb -ac :99 & [dix] Could not init font path element /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType, removing from list! (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) $ firefox [dix] Could not init font path element /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType, removing from list! [config/dbus] couldn't register object path (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) Xlib: extension "RANDR" missing on display ":99.0". GConf Error: Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /bin/dbus-launch terminated abnormally without any error message) I'm runnig firefox without installing it from the repositories. And I'm getting a socket timeout when I try to run the selenium tests, so I guess the problem is in Firefox and Xvfb. I have installed already the nex package: i gconf-defaults-service - GNOME configuration database system (system defaults service) That in some forums suggest to be a fix, that in my case doesn't work. Any explanation about the problem and ways of solving it without installing a full gui, will be very helpful.

  Read the article

• Terrible noises from subwoofer of ACER Aspire 6930 with Realtek sound chip

  - by OneWorld

  After approximately 5-15 min of listening to music my subwoofer begins to make terrible noises. He's just "coughing". That began after 6 months I had this computer. Now I found out, that I can temporarily fix this problem by "restarting" the audio stream of the application that plays music. For example reloading last.fm page (reloads the flash file). Another way to reset the audio playback is switching the speaker configuration shown below in the screenshot. According to many posts on the internet like http://www.tomshardware.co.uk/forum/52918-20-acer-aspire-6935g-speaker-problem ACER support isn't any help Exchanging hardware doesn't fix the problem Even the later models have this problem Turning off the volume of the subwoofer is not an option to me. I still have warranty (I bought an extension of one year). I already tried about 15 versions of the Realtek driver with no success. I am not sure but MAYBE the problem did not occur on the original windows vista that was shipped with this computer. However, I removed the original windows for good reasons (english). What do you suggest me? Did anyone fix this problem? Maybe by writing a script which resets the audio streams every 5 minutes? Shall I take the effort to deal with the acer support until they give me another model? (I won't have a computer than for a longer time, will spend money on telephone hotlines (1,30 EUR / min)......) Here are additional infos, if they are any help: Windows 7 64 Bit (Original was Windows Vista Home Premium 32 Bit) All specs Audio driver version:

  Read the article

• Hiera datatypes wont load in Puppet

  - by Cole Shores

  I have spent a couple of days on this, followed the instructions on http://downloads.puppetlabs.com/docs/puppetmanual.pdf and even the Puppet Training Advanced Puppet manual. When I run a test against it, the results always come back as 'nil' and Im not sure why. I am running Puppet 3.6.1 Community Edition, with Hiera 1.2.1 on SLES 11. My puppet.conf file at /etc/puppet/puppet.conf consists of: [main] # The Puppet log directory. # The default value is '$vardir/log'. logdir = /var/log/puppet # Where Puppet PID files are kept. # The default value is '$vardir/run'. rundir = /var/run/puppet # Where SSL certificates are kept. # The default value is '$confdir/ssl'. ssldir = $vardir/ssl certificate_revocation = false [master] hiera_config=/etc/puppet/hiera.yaml reporturl = http://puppet2.vvmedia.com/reports/upload ssl_client_header = SSL_CLIENT_S_DN ssl_client_verify_header = SSL_CLIENT_VERIFY # certname = dev-puppetmaster2.vvmedia.com # ca_name = 'dev-puppetmaster2.vvmedia.com' # facts_terminus = rest # inventory_server = localhost # ca = false [agent] # The file in which puppetd stores a list of the classes # associated with the retrieved configuratiion. Can be loaded in # the separate ``puppet`` executable using the ``--loadclasses`` # option. # The default value is '$confdir/classes.txt'. classfile = $vardir/classes.txt # Where puppetd caches the local configuration. An # extension indicating the cache format is added automatically. # The default value is '$confdir/localconfig'. localconfig = $vardir/localconfig my /etc/puppet/hiera.yaml consists of: :backends: yaml :yaml: :datadir: /etc/puppet/hieradata :hierarchy: - common - database I have a directory created in /etc/puppet/hieradata and within it contains: /etc/puppet/hieradata/common.yaml :nameserver: ["dnsserverfoo1", "dnsserverfoo2"] :smtp_server: relay.internalfoo.com :syslog_server: syslogfoo.com :logstash_shipper: logstashfoo.com :syslog_backup_nfs: nfsfoo:/vol/logs :auth_method: ldap :manage_root: true and /etc/puppet/hieradata/database.yaml :enable_graphital: true :mysql_server_package: MySQL-server :mysql_client_package: MySQL-client :allowed_groups_login: extranet_users does anyone have any idea what could be causing Hiera to not load the requested values? I have tried even restarting the Master. Thanks in advance, Cole

  Read the article

• Unable to specify parameters to cvlc in a script

  - by VxJasonxV

  I'm creating a script that issues a few curl commands in order to access a time-protected mms stream link, then set up a relay using cvlc (vlc's command line interface) for my own use on an unencumbered player. The curl aspect of this is working, as I can run as a browser and curl side by side and get the same access url. (It's time locked meaning the stream will work forever, but you have to connect quickly or the URL will time out.) The very end of the script prints the command I will run, which is then followed up by "exec $CMD". When I echo $CMD I get: cvlc --sout '#standard{access=http,mux=asf,dst=0.0.0.0:58194}' mms://[...] Manually Copy/Pasting this command in, verbatim, works perfectly fine, but as part of a script, the cvlc execution output says: [0x9743d0] main interface error: no suitable interface module [0x962120] main libvlc error: interface "globalhotkeys,none" initialization failed [0x9743d0] dummy interface: using the dummy interface module... [0xb16e30] stream_out_standard stream out error: no mux specified or found by extension [0xb16ad0] main stream output error: stream chain failed for `standard{mux="",access="",dst="'#standard{access=http,mux=asf,dst=0.0.0.0:58194}'"}' [0xb11cd0] main input error: cannot start stream output instance, aborting [0xb11f70] signals interface error: Caught Interrupt signal, exiting... Why is --sout behaving one way in a script (non-interactive shell?) vs. another way in the foreground (interactive shell) ?

  Read the article

• FastCGI Error when installing PHP on IIS7.5

  - by ytoledano

  I'm trying to install MediaWiki on a Win2008r2 server, but can't manage to install PHP. Here's what I did: Grabbed a Zip archive of PHP and unzipped it into C:\PHP. Created two subdirs: c:\PHP\sessiondata and c:\PHP\uploadtemp. Granted modify rights to the IUSR account for the subdirs. Copied php.ini-production as php.ini Edited php.ini and made the following changes: fastcgi.impersonate = 1 cgi.fix_pathinfo = 1 cgi.force_redirect = 0 open_basedir = "c:\inetpub\wwwroot;c:\PHP\uploadtemp;C:\PHP\sessiondata" extension = php_mysql.dll extension_dir = "./ext" upload_tmp_dir = C:\PHP\uploadtemp session.save_path = C:\php\sessiondata Install Web server role, selected CGI and HTTP Redirection options. In the Handler Mappings: Added Module Mapping. Entered the following values: Path = *.php, Module = FastCgiModule, Executable = c:\php\php-cgi.exe, Name = PHP via FastCGI. Created a test page into wwwroot directory: phpinfo.php and set the contents like this: < ?php phpinfo(); ? Browsed to http://localhost/phpinfo.php But then I get: HTTP Error 500.0 - Internal Server Error An unknown FastCGI error occured Detailed Error Information Module: FastCgiModule Notification: ExecuteRequestHandler Handler: PHP via FastCGI Error Code: 0x800736b1 Requested URL: http://localhost:80/phpinfo.php Physical Path: C:\inetpub\wwwroot\phpinfo.php Logon Method: Anonymous Logon User: Anonymous Does anyone know what I'm doing wrong here? Thanks.

  Read the article

• Fix Video timelines

  - by Josh

  So, I have been going through and riping all of my DVD's and it seems that the way to get the highest quality out of these is to have DVD Shrink de-encrypt, rip, and decompress, the DVD's. After that I usually end up with a high quality (high size) set of .vob files in a classic DVD structure. Then I use a python script that I wrote to automate the process of finding the title sequence and then combining all of the title sequences' .vob files together into one file(similar to the "copy /b" command in windows), and then changing the extension to .mpg (a more widely supported format then .vob). This allows me to get a high quality rip in about 40 min. The problem comes in playing the files. I need all of the ripped dvd's to play on my media computer using windows media center but windows media center (and vlc for that matter) all think that the video files are anywhere from 5 min. to 0 min. which is not a problem (the video will still play all the way through) but if you want to pause it, when it is unpaused the video will start all the way over (Also fast forward and rewind don't work). I suspect that it is something wrong with the way the timeline is encoded in the video file, various forums on the internet recommended using virtualdub to fix the errors. But when I try to open the file virtual dub says that the file is not in mpeg-1 encoding and may be in mpeg-2. Is there any way to fix this? PS: I am aware that there was a similar question but it hasn't had any activity for 2 months and is dealing more with wmv files.

  Read the article

• How can I make Internet Explorer 6 render Web pages like Internet Explorer 11?

  - by gparyani

  Now, I know that this may seem like a bad question in that I can just upgrade to Internet Explorer 8, but I am sticking with IE6 in that IE8 removes valuable features, like the ability to save favorites offline and the fact that a file path turns into a Windows Explorer window and typing a Web address into Windows Explorer changes it into an IE window. I know that Internet Explorer 6 does a really bad job at rendering some pages. I know of the Google Chrome Frame extension that brings Chrome-style rendering into IE, but that will soon be discontinued. So, I tried another thing: I know that C:\Windows\System32\mshtml.dll contains the Trident rendering engine that is used by IE, so I tried something: I first backed up the original file by renaming it on Windows XP to mshtml-old.dll, then I tried to copy in the DLL from a computer running Windows 7 with Internet Explorer 10. I noticed that, after copying, the system had replaced the new DLL with the old one, but left the one I backed up intact. Is there any way I can get the system to not replace the DLL like that so that I can transfer in IE11's mshtml.dll into Windows XP and make IE6 render like IE11? I'm looking for an answer that describes how to tweak my system to make IE6 render like IE11 (or IE10), not one that tells me to upgrade IE or install another browser. I don't care how tedious the method is, just as long as it works.

  Read the article

• Apache-style multiviews with Nginx

  - by Kenn

  I'm interested in switching from Apache/mod_php to Nginx for some non-CMS sites I'm running. The sites in question are either completely static HTML files or simple PHP, but the one thing they have in common is that I'm currently using Apache's mod_negotiation to serve them up without file extensions. I'm not concerned with actual content negotiation; I'm using this just so I don't have to use file extensions in my URLs. For example, the file at /info/contact.php is accessed via a URL of just /info/contact The actual file is a .php file in that location, but I don't use the extension in the URLs. This gives me slightly shorter, cleaner URLs and also doesn't expose what's essentially a meaningless implementation detail to the user. In Apache, all this takes is enabling mod_negotiation and adding +MultiViews to the Options for the site. In Nginx I gather I'll be rewriting somehow but being new to Nginx, I'm not exactly sure how to do it. These sites are currently working fine proxied from Nginx to Apache, but I'd like to try running them solely with Nginx/fastcgi. They work fine this way as long as I'm using the extensions, so the fastcgi aspect is working great. My concern now is just with removing those extensions. It's important to keep in mind that the filename is not always in the URL, in the case of subdirectories. That is, /foo/bar should look for /foo/bar.php or /foo/bar/index.php /foo/ should look for /foo/index.php Is there a simple way to achieve this with Nginx or should I stick with proxying to Apache?

  Read the article

• How to install the MySQL Ruby Gem on Ubuntu 9.10?

  - by misbehavens

  I am having a problem installing the Ruby Gem for MySQL. This is the command that I am running: sudo gem install mysql and this is the output that I'm getting: Building native extensions. This could take a while... ERROR: Error installing mysql: ERROR: Failed to build gem native extension. /usr/bin/ruby1.8 extconf.rb checking for mysql_query() in -lmysqlclient... no checking for main() in -lm... yes checking for mysql_query() in -lmysqlclient... no checking for main() in -lz... yes checking for mysql_query() in -lmysqlclient... no checking for main() in -lsocket... no checking for mysql_query() in -lmysqlclient... no checking for main() in -lnsl... yes checking for mysql_query() in -lmysqlclient... no checking for main() in -lmygcc... no checking for mysql_query() in -lmysqlclient... no *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby1.8 --with-mysql-config --without-mysql-config --with-mysql-dir --without-mysql-dir --with-mysql-include --without-mysql-include=${mysql-dir}/include --with-mysql-lib --without-mysql-lib=${mysql-dir}/lib --with-mysqlclientlib --without-mysqlclientlib --with-mlib --without-mlib --with-mysqlclientlib --without-mysqlclientlib --with-zlib --without-zlib --with-mysqlclientlib --without-mysqlclientlib --with-socketlib --without-socketlib --with-mysqlclientlib --without-mysqlclientlib --with-nsllib --without-nsllib --with-mysqlclientlib --without-mysqlclientlib --with-mygcclib --without-mygcclib --with-mysqlclientlib --without-mysqlclientlib Gem files will remain installed in /usr/lib/ruby/gems/1.8/gems/mysql-2.8.1 for inspection. Results logged to /usr/lib/ruby/gems/1.8/gems/mysql-2.8.1/ext/mysql_api/gem_make.out What do I need to do in order to get this to install?

  Read the article

< Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >