Search Results

Search found 5205 results on 209 pages for 'extra'.

Page 176/209 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• Triple (3) Monitors under Linux

  - by widgisoft

  I have a 3 monitor setup (each 1680x1050) via an Nvidia NVS440 (2 GPUs, 2 outputs per GPU totalling 4 outputs); this works fine under Windows XP,7 but caused considerable headaches under Linux (Ubuntu 9.04). I had previously used an XFX 9600GT and the onboard XFX 9300GS to produce the same result but the card was noisy and power hungry and I was hoping that there was some magical switch in the NVS4400 that got rid of this annoying problem - turns out the NVS440 is just 2 cards on one physical PCB :-p (I searched the net high and low for people using this card under Linux but found nothing, if anything the card uses less power and is fan less so I was to benefit from it either way) Anyway, using either set up there were 5 solutions available: Have 3 separate X instances, all un joined Have 3 separate X instances, adjoined by Xinerama Have 2 separate X instances - One using twin-view, both adjoined by Xinerama Have 2 separate X instances - One using twin-view but no Xinerama Have a single Twin-view setup and leave the 3rd screen unplugged :-p The 4rd option, using 2 separate X instances and twinview (but no xinerama) was the best balance in terms of performance and usability but caused 2 really annoying issues You couldn't control (without altering the shortcuts) which screen an application opened onto - and once it was opened you couldn't move it to another screen without opening up terminal and forcing it to move Nvidia's overriding or falsifying of Xinerama breaks and the 2 screens joined by Twin view behave like a single huge screen causing popups to open in the middle of both screens and maximising of windows stretches to the width of the first 2 screens Firefox can only run one instance as the same user so having multiple firefox windows requires at least 2 users The second option "feels" like the right option, but OpenGL is basically disabled and playing any sort of game or even running anything graphical causes a huge performance drop and instability - even trying to run a basic emulator for gba or gens just causes the system to fall over. It works just enough to stare at your desktop and do nothing but as soon as you start doing some work - opening windows, dragging things around - running multiple copies of firefox it just really feels slow. The last open, only going dual screen works perfectly and everything performs as required, full GPU acceleration - two logical screen spaces - perfect, just make it work across GPUs like windows! :-p Anyway, I know RandR was supposed to pick up the slack when it would introduced GPU objects of sorts to allow multiple GPUs to be stitched together to create one huge desktop at a much deeper layer than Xinerama. I was wondering if this has now been fixed (I noticed X server 1.7 is out) and whether anyone has got it running successfully? Again, my requirements are: One huge desktop to drag any window across Maximising of windows to each screen (as XP does) Running fullscreen apps on the primary screen and disabling the mouse from moving onto the others or on all 3 stretched Finally as a side note; I am aware of the Matrox triple (and dual) head splitter but even the price they go for on eBay is more than I can afford atm, my argument: I shouldn't have to buy extra hardware to get something to work on Linux when it's something that's existed in the windows world for a long time (can you tell I don't get on with X :-p); If I had the cash I'd have bought the latest version of this box already (the new version finally supports large resolutions as the displays I have 1680x1050 each).

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files)

  - by user11955

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• Does 64bit Windows 8 have the same 75% memory-usage limitation for applications as Windows 7?

  - by Barleyman

  64bit Windows 7 (and Windows Vista) have a built-in limit of not being able to use the last 25% of RAM. You will get a low memory warning when you get close to the limit. Even if you disable that warning, applications will run out of memory and crash since the OS will refuse to allocate memory from that last 25%. That was fine when Vista was designed, when machines had 1 GB of total memory, but is pretty daft for today's 8 GB machines. Yes, the system will run cache, etc. on that extra 2 GB, but running out of memory when you have "merely" 2 GB left.... NB: this has nothing to do with the page file. If you limit the page file to a sensible size like 2 GB, you will still see this behavior. The system will cram the page file to the last byte while refusing to touch that 1/4th of the RAM. Does Windows 8 change this behavior? Is there now some fixed minimum free RAM requirement, like 512 MB, or is it still 25%? Can you actually adjust the low memory limit? EDIT: Here is another older post here which discusses this same behavior on Windows 7. There is fixed 25% limit in Windows 7 and I'd like to know if it's still in Windows 8. Windows 7 / Page File Disabled / 12 GB RAM / 2+ GB RAM free and "your computer is running low on memory" Edit2: Here is another link discussing the low memory warning and how to disable it. Note he claims the limit for RAM usage is 80%, not 75%. It would seem to be correct as you can in fact allocate 6.4GB of RAM with 8GB machine. Anything above and beyond that goes to the pagefile, though. http://halflight.com.au/2011/04/06/how-to-disable-low-memory-warnings-and-the-advantages-of-removing-the-page-file/ Edit3: a Here's couple of process explorer screenshots that demonstrate how it goes down. Exhibit1: https://dl.dropbox.com/u/42068601/sysinfo.jpg Exhibit2: https://dl.dropbox.com/u/42068601/sysint2.jpg You can see that Windows 7 will use the memory 6.4GB as the very last resort. I have low memory warning switched off here so programs crashed at the last screenshot allocation. With low memory warning turned on, it starts nagging before you can push OS to use that remaining 1.6GB. The question is not "Is it OK windows does not want to allocate last 20% of RAM because X", it's "Does Windows 8 still behave this way". With 16GB this really becomes dumb.

  Read the article

• Is there a Distributed SAN/Storage System out there?

  - by Joel Coel

  Like many other places, we ask our users not to save files to their local machines. Instead, we encourage that they be put on a file server so that others (with appropriate permissions) can use them and that the files are backed up properly. The result of this is that most users have large hard drives that are sitting mainly empty. It's 2010 now. Surely there is a system out there that lets you turn that empty space into a virtual SAN or document library? What I envision is a client program that is pushed out to users' PCs that coordinates with a central server. The server looks to users just like a normal file server, but instead of keeping entire file contents it merely keeps a record of where those files can be found among various user PCs. It then coordinates with the right clients to serve up file requests. The client software would be able to respond to such requests directly, as well as be smart enough to cache recent files locally. For redundancy the server could make sure files are copied to multiple PCs, perhaps allowing you to define groups in different locations so that an instance of the entire repository lives in each group to protect against a disaster in one building taking down everything else. Obviously you wouldn't point your database server here, but for simpler things I see several advantages: Files can often be transferred from a nearer machine. Disk space grows automatically as your company does. Should ultimately be cheaper, as you don't need to keep a separate set of disks I can see a few downsides as well: Occasional degradation of user pc performance, if the machine has to serve or accept a large file transfer during a busy period. Writes have to be propogated around the network several times (though I suspect this isn't really much of a problem, as reading happens in most places more than writing) Still need a way to send a complete copy of the data offsite occasionally, and this would make it very hard to do differentials Think of this like a cloud storage system that lives entirely within your corporate LAN and makes use of your existing user equipment. Our old main file server is due for retirement in about 2 years, and I'm looking into replacing it with a small SAN. I'm thinking something like this would be a better fit. As a school, we have a couple computer labs I can leave running that would be perfect for adding a little extra redundancy to the system. Unfortunately, the closest thing I can find is Dienst, and it's just a paper that dates back to 1994. Am I just using the wrong buzzwords in my searches, or does this really not exist? If not, is there a big downside that I'm missing?

  Read the article

• joining text files with 600M+ lines

  - by dnkb

  I have two files huge.txt and small.txt. Huge has around 600M rows and it's 14Gigs, each line has four space separated words (tokens) and finally another space separated column with a number. Small has 150K rows with a size of ~3M, a space separated word and a number. Both Files are sorted using the sort command, with no extra options. The words in both files may include apostrophes (') and dashes (-). The deisred output would contain all columns from the huge.txt and the second column (the number) from small txt where the first word of huge.txt and the first word of small.txt match. My attemtpts below failed miserably with the following error: cat huge.txt|join -o 1.1 1.2 1.3 1.4 2.2 - small.txt > output.txt join: memory exhausted What I suspect is that the sorting order isn't right somehow even though the files are pre-sorted using: sort -k1 huge.unsorted.txt > huge.txt sort -k1 small.unsorted.txt > small.txt Problems seem to appear around words that have apostrophes (') or dashes (-). I also tried dictinoary sorting using the -d option bumping into the same error at the end. I see two ways out of this but don't know how to implement any of them. 1) Any tips how to sort the files in a way that the join command considers them to be sorted properly? 2) I was thinking of calculating MD5 or some other hashes of the strings to get rid of the apostrophes and dashes, and do the sorting and joining with the hashes instead of the strings themselves an dat the "translate" back the hashes to strings, but leave the numbers intact at the end of the lines. Since there would be only 150K hashes it's not that bad. What would be a good way to calculate individual hashes for each of the strings? Some AWK magic? See file samples at the end. Thank you! sample of huge.txt had stirred me to 46 had stirred my corruption 57 had stirred old emotions 55 had stirred something in 69 had stirred something within 40 sample of small.txt caley 114881 calf 2757974 calfed 137861 calfee 71143 calflora 154624 calfskin 148347 calgary 9416465 calgon's 94846

  Read the article

• Varnish server in front of nginx server with multiple virtualhosts

  - by Garreth 00

  I have tried to search for a solution for this, but can't find any documentation/tips on my specific setup. My setup: Backendserver: ngnix: 2 different websites (2 top domains) in virtualenv, running gunicorn/python/django Backendserver hardware(VPS) 2gb ram, 8 CPU Databaseserver: postgresql - pg_bouncer Backendserver hardware (VPS) 1gb ram, 8 CPU Varnishserver: only running varnish Varnishserver hardware (VPS) 1gb ram, 8 CPU I'm trying to set up a varnish server to handle rare spike in traffic (20 000 unique req/s) The spike happens when a tv program mention one of the sites. What do I need to do, to make the varnish server cache both sites/domains on my backendserver? My /etc/varnish/default.vcl : backend django_backend { .host = "local.backendserver.com"; .port = "8080"; } My /usr/local/nginx/site-avaible/domain1.com upstream gunicorn_domain1 { server unix:/home/<USER>/.virtualenvs/<DOMAIN1>/<APP1>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain1.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80 default_server; listen 8080; client_max_body_size 4G; server_name www.domain1.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain1; break; } } } My /usr/local/nginx/site-avaible/domain2.com upstream gunicorn_domain2 { server unix:/home/<USER>/.virtualenvs/<DOMAIN2>/<APP2>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain2.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80; listen 8080; client_max_body_size 4G; server_name www.domain2.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain2; break; } } } Right now, If I try the Ip of the varnishserver I only get served domain1.com. Would everything be correct if I change the DNS of the two domain to point to the varnishserver, or is there extra setup before it would work? Question 2: Do I need a dedicated server for varnish, or could I just install varnish on my backendserver, or would the server run out of memory quick?

  Read the article

• Will spreading your servers load not just consume more recourses

  - by Saif Bechan

  I am running a heavy real-time updating website. The amount of recourses needed per user are quite high, ill give you an example. Setup Every visit The application is php/mysql so on every visit static and dynamic content is loaded. Recourses: apache,php,mysql Every second (no more than a second will just be too long) The website needs to be updated real-time so every second there is an ajax call thats updates the website. Recourses: jQuery,apache,php,mysql Avarage spending for single user (spending one minute and visited 3 pages) Apache: +/- 63 requests / responsess serving static and dynamic content (img,css,js,html) php: +/- 63 requests / responses mysql: +/- 63 requests / responses jquery: +/- 60 requests / responses Optimization I want to optimize this process, but I think that maybe it would be just the same in the end. Before implementing and testing (which will take weeks) I wanted to have some second opinions from you guys. Every visit I want to start off with having nginx in the front and work as a proxy to deliver the static content. Recources: Dynamic: apache,php,mysql Static: nginx This will spread the load on apache a lot. Every Second For the script that loads every second I want to set up Node.js server side javascript with nginx in te front. I want to set it up that jquery makes a request ones a minute, and node.js streams the data to the client every second. Recources: jQuery,nginx,node.js,mysql Avarage spending for single user (spending one minute and visited 3 pages) Nginx: 4 requests / responsess serving mostly static conetent(img,css,js) Apache: 3 requests only the pages php: 3 requests only the pages node.js: 1 request / 60 responses jquery: 1 request / 60 responses mysql: 63 requests / responses Optimization As you can see in the optimisation the load from Apache and PHP are lifted and places on nginx and node.js. These are known for there light footprint and good performance. But I am having my doubts, because there are still 2 programs extra loaded in the memory and they consume cpu. So it it better to have less programs that do the job, or more. Before I am going to spend a lot of time setting this up I would like to know if it will be worth the while.

  Read the article

• Sycronizing/deploying scripts across several systems

  - by otto

  I have a few time consuming tasks that I like to spread across several computers. These tasks require running an identical ruby or python script (or series of scripts that call each other) on each machine. The machines will a separate config file telling the script what portion of the task to complete. I want to figure out the best way to syncronize the scripts on these machines prior to running them. Up until now, I have been making changes to a copy of the script on a network share and then copying a fresh copy to each machine when I want to run it. But this is cumbersome and leaves a chance for error ( e.g missing a file on the copy or not clicking "copy and replace"). Lets assume the systems are standard windows machines that are not dedicated to this task and I don't need to run these scripts all the time (so I don't want a solution that runs 24/7 and always keeps them up to date, I'd prefer something that pushes/pulls on command). My thoughts on various options: Simple adaptation of my current workflow: Keep the originals on the network drive, but write a batch file that copies over the latest version of the scripts so everything is a one-click operation. Requires action on each system, but that's not the end of the world (since each one usually needs their configuration file changed slightly too). Put everything in a Mercurial/Git reposotory and pull a fresh copy onto each node. Going straight to the repo from each machine would guarantee a current version (and would have the fringe benefit of allowing edits to the script to be made from any machine). Cons would be that it requires VCS to be installed on each machine and there might be some pains dealing with authentication since I wouldn't use a public repo. Open up write access on a shared folder and write a script to use rsync (or similar) to push the changes out to all of the machines at once. This gets a current version on every machine (though you would have to change the script if you want to omit a machine or add a new one). Possible issue would be that each computer has to allow write access. Dropbox is a reasonable suggestion (and could work well) but I dont want to use an external service and I'd prefer not to have to have dropbox running 24/7 on systems that would normally not need it. Is there something simple that I am missing? Some tool designed expressly for doing this kind of thing? Otherwise I am leaning toward just tying all of the systems into Mercurial since, while it requires extra software, it is a little more robust than writing a batch file (e.g. if I split part of a script into a separate module, Mercurial will know what to do whereas I would have to add a line to the batch file).

  Read the article

• Linux Best Practices

  - by Zac

  I'm a life-long Windows developer switching over to Linux for the first time, and I'm starting off with Ubuntu to ease the learning curve. My new laptop will primarily be a development machine: 6GB RAM, 320 GB HD. I'd like there to be 2 non-root users: (a) Development, which will always be me, and (b) Guest, for anyone else. I assume the root user is added by default, like System Administrator in Windows. (1) I'd like to mount /home to its own partition, but how does this work if I have two user accounts (Development and Guest)? Are there 2 separate /home directories, or do they get shared? Is it possible to allocate more space for Development and only a tiny bit of space for Guest in GRUB2? How?!?! (2) I'm assuming that its okay that all of my development tools (Eclipse & plugins, SVN, JUnit, ant, etc.) and Java will end up getting installed in non-/home directories such as /usr and /opt, but that my Eclipse/SVN workspace will live under my /home directory on a separate partition... any problems, issues, concerns with that? (3) As far as partitioning schemes, nothing too complicated, but not plain Jane either: Boot Partition, 512 MB, in case I want to install other OSes Ubuntu & non-/home file system, 187.5 GB Swap Partition, 12 GB = RAM x 2 /home Partition, 120 GB I don't have any bulky media data (I don't have music or video libraries, this is a lean and mean dev machine) so having 320 GB is like winning the lottery and not knowing what to do with all this space. I figured I'd give a little extra space to the OS/FS partition since I'll be running JEE containers locally and doing a lot of file IO, logging and other memory-instensive operations. Any issues, problems, concerns, suggestions? (4) I was thinking about using ext4; seems to have good filestamping without any space ceiling for me to hit. Any other suggestions for a dev machine? (5) I read somewhere that you need to be careful when you install software as the root user, but I can't remember why. What general caveats do I need to be aware of when doing things (installing packages, making system configurations, etc.) as root vs "Development" user? Thanks!

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Trying to setup virtual hosts on unix PHP on nginx

  - by user1634653

  I have tried to install php5-fpm and Nginx on Ubuntu machine, but I got a problem. When I have only one virtual host on a unix port it is all fine but when I try to add another virtual host Nginx goes to default web page "Welcome to Nginx!" but when I run it on a tcp port example port 9000 it work fine with multisites. It is a fresh install of ubuntu 11.10, Nginx 1.2.3 with php5-fpm installed. It also has extra php installs such as php-apc. I can only give the links to the virtual hosts because I am doing it from a mobile phone. Here are the links for the two virtual hosts I am using: http://ic0nic.co.uk/ic0nic.txt, http://ic0nic.co.uk/sourproxy.txt also I want to use unix port because I find it a whole lot faster. Edit: Here are the nginx configs server { server_name ic0nic.co.uk www.ic0nic.co.uk; root /var/www/ic0nic.co.uk; listen 8080; index index.html index.htm index.php; include conf.d/drop; location / { try_files $uri $uri/ /index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_buffers 8 256k; fastcgi_buffer_size 128k; fastcgi_intercept_errors on; include fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_pass unix:/dev/shm/php-fpm-www.sock; root /var/www/ic0nic.co.uk; } } server { server_name sourproxy.co.uk www.sourproxy.co.uk; root /var/www/sourproxy.co.uk/; listen 8080; index index.html index.htm index.php; include conf.d/drop; location / { try_files $uri $uri/ /index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_buffers 8 256k; fastcgi_buffer_size 128k; fastcgi_intercept_errors on; include fastcgi_params; fastcgi_param SCRIPT_FILENAME /var/www/sourproxy.co.uk$fastcgi_script_name; fastcgi_pass unix:/dev/shm/php-fpm-www.sock; } }

  Read the article

• Recovering from backup without original install media

  - by KGendron

  A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

  Read the article

• Windows Server 2008 R2 bare metal restore to different hardware

  - by S Falken

  Scenario: I have a Windows Server 2008 R2 x64 installation whose main disk drive is now 7 years old and showing signs of age. For the last couple of months it's been displaying increased errors and requirements to run checkdisk. I have successfully created a bare metal restore (BMR) image on a separate data drive on the server, which can be seen from the Windows Recovery console; I tested it by booting to and using the Windows Server installation DVD's recovery utilities. The BMR image includes the system drive with boot partition, system state, and the D:\ drive of the server, which is where I have followed the practice of installing any program that does not require a C:\ installation path. Therefore, the BMR includes both the C:\ and D:\ drives, system state and boot partition. The C:\ drive is a 7-year old Seagate 160GB. The D:\ drive is a rather newer 120GB Western Digital. I have purchased a 128GB solid state Samsung 830 that I want to restore these partitions to, using the BMR. Questions: In the above-referenced article, Microsoft seems to be indicating that I am only able to restore to like-kind hardware, which doesn't help at all and is difficult to believe. Is this really true? I've cleaned these drives up and minimized the size of partition they require. C:\ will need about a 70GB partition, and the data on D:\ will need about 50GB. Will Windows Server backup allow me to restore the BMR to newly-created partitions on the SSD, discarding extra space? I don't need a "how-to": I just need an "is it possible". Justification: Before posting this question, I checked ServerFault articles with the following titles, but none of them were about this exact scenario: Restore SBS 2008 Backup to Same Hardware but Different Disk Configuration Restoring Windows Server 2008 to different hardware - OEM License Restoring II6 server after a hardware failure windows 2008 r2 fail to restore Domain controller failed to restore using windows backup tools How does restore to dissimilar hardware work? Migrating Windows 2008 R2 from a PC to a different PC TFS 2005 Server restore from one hardware to another I also researched Microsoft but only received an oblique answer which was not precisely aimed at my question, at the following URL: http://support.microsoft.com/kb/249694#method3

  Read the article

• How to prevent dual booted OSes from damaging each other?

  - by user1252434

  For better compatibility and performance in games I'm thinking about installing Windows additionally to Linux. I have security concerns about this, though. Note: "Windows" in the remaining text includes not only the OS but also any software running on it. Regardless of whether it comes included or is additionally installed, whether it is started intentionally or unintentionally (virus, malware). Is there an easy way to achieve the following requirements: Windows MUST NOT be able to kill my linux partition or my data disk neither single files (virus infection) nor overwriting the whole disk Windows MUST NOT be able to read data disk (- extra protection against spyware) Linux may or may not have access to the windows partition both Linux and Windows should have full access to the graphics card this rules out desktop VM solutions for gaming I want the manufacturer's windows graphics card driver Regarding Windows to be unable to destroy my linux install: this is not just the usual paranoia, that has happened to me in the past. So I don't accept "no ext4 driver" as an argument. Once bitten, twice shy. And even if destruction targeted at specific (linux) files is nearly impossible, there should be no way to shred the whole partition. I may accept the risk of malware breaking out of a barrier (e.g. VM) around the whole windows box, though. Currently I have a system disk (SSD) and a data disk (HDD), both SATA. I expect I have to add another disk. If i don't: even better. My CPU is a Intel Core i5, with VT-x and VT-d available, though untested. Ideas I've had so far: deactivate or hide other HDs until reboot at low level possible? can the boot loader (grub) do this for me? tiny VM layer: load windows in a VM that provides access to almost all hardware, except the HDs any ready made software solution for this? Preferably free. as I said: the main problem seems to be to provide full access to the graphics card hardware switch to cut power to disks commercial products expensive and lots of warnings against cheap home built solutions preferably all three hard disks with one switch (one push) mobile racks - won't wear of daily swapping be a problem?

  Read the article

• QNAP (469L) with Debian: can't connect to router

  - by agtoever

  I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

  Read the article

• Nginx SSL redirect for one specific page only

  - by jjiceman

  I read and followed this question in order to configure nginx to force SSL for one page (admin.php for XenForo), and it is working well for a few of the site administrators but is not for myself. I was wondering if anyone has any advice on how to improve this configuration: ... ssl_certificate example.net.crt; ssl_certificate_key example.key; server { listen 80 default; listen 443 ssl; server_name www.example.net example.net; access_log /srv/www/example.net/logs/access.log; error_log /srv/www/example.net/logs/error.log; root /srv/www/example.net/public_html; index index.php index.html; location / { if ( $scheme = https ){ rewrite ^ http://example.net$request_uri? permanent; } try_files $uri $uri/ /index.php?$uri&$args; index index.php index.html; } location ^~ /admin.php { if ( $scheme = http ) { rewrite ^ https://example.net$request_uri? permanent; } try_files $uri /index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS on; } location ~ \.php$ { try_files $uri /index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS off; } } ... It seems that the extra information in the location ^~ /admin.php block is unecessary, does anyone know of an easy way to avoid duplicate code? Without it it skips the php block and just returns the php files. Currently it applies https correctly in Firefox when I navigate to admin.php. In Chrome, it downloads the admin.php page. When returning to the non-https website in Firefox, it does not correctly return to http but stays as SSL. Like I said earlier, this only happens for me, the other admins can go back and forth without a problem. Is this an issue on my end that I can fix? And does anyone know of any ways I could reduce duplicate configuration options in the configuration? Thanks in advance! EDIT: Clearing the cache / cookies seemed to work. Is this the right way to do http/https redirection? I sort of made it up as I went along.

  Read the article

• OEM sound card with no drivers or support

  - by randy

  I thought my sound card was going out so I bought a sound card online. Everything seemed to work ok, I do have sound. But after a few months, I noticed the extra software that downloaded with the sound card drivers didn't work. I ended up contacting creative and after a month of e-mail support, they asked for the serial number and/or model number. Their reply back was I had purchased an OEM sound card and they could not provide support for that, and informed me that that is why their drivers and software didn't work. They informed me that I had to contact the company that distributed the sound card and install their software. Is there anything I can do to find out who distributed this sound card, or is there anything I can do to get other features to work? I have 4 speakers and a sub but only 2 speakers produce sound. The only control I have is the volume. Creative's driver update program will find my sound card, download updates and even added software, but if I try to click on a downloaded program like Creative's Toolbox or Media Center, I get an error that it cannot find the devise. That is why I contacted creative in the first place. EDIT Thanks for the responses everyone. Here's an update. I thought I'd go thru my old computer stuff for my classes at school. I have a lot of old stuff saved, boxes and cables and stuff. I found the box the sound card came in. It looks like a box you'd buy at the store, like Best Buy or CompUSA. I worked with creative for such a long time, it went past the point of being able to return it to the junk online store this shipped from. The box did have an install CD, so I thought I'd start over to reinstall the drivers and software that shipped with the card. I noticed that the install would uninstall a program, then reinstall it. so I thought things were working out. But no good. Everything still works but the programs were still bad. I'd get an error trying to load them - not found. I'll look on the card the next time I get a chance and see if I can spot any kind of name on it.

  Read the article

• Create text file named after a cell containing other cell data

  - by user143041

  I tried using the code below for the Excel program on my `Mac Mini using the OS X Version 10.7.2 and it keeps saying Error due to file name / path: (The Excel file I am creating is going to be a template with my formulas and macros installed which will be used over and over). Sub CreateFile() Do While Not IsEmpty(ActiveCell.Offset(0, 1)) MyFile = ActiveCell.Value & ".txt" fnum = FreeFile() Open MyFile For Output As fnum Print #fnum, ActiveCell.Offset(0, 1) & " " & ActiveCell.Offset(0, 2) Close #fnum ActiveCell.Offset(1, 0).Select Loop End Sub What Im trying to do: 1st Objective I would like to have the following data to be used to create a text file. A:A is what I need the name of the file to be. B:2 is the content I need in the text file. So, A2 - "repair-video-game-Glassboro-NJ-08028.txt" is the file name and B2 to be the content in the file. Next, A3 is the file name and B3 is the content for the file, etc. ONCE the content reads what is in cell A16 and B16 (length will vary), the file creation should stop, if not then I can delete the additional files created. This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? 2nd Objective I would like to have the following data to be used to create a text file. A:1 is what I need the name of the file to be. B:B is the content I want in the file. So, A2 - is the file name "geo-sitemap.xml" and B:B to be the content in the file (ignore the .xml file extension in the photo). ONCE the content cell reads what is in cell "B16" (length will vary), the file creation should stop, if not then I can adjust the cells that have need content (formulated content you see in the image is preset for 500 rows). This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? I can Provide the content in the cells that are filled in by excel formulas that are not not to be included in the .txt files. It is ok if it is not possible. I can delete the extra cells that are not populated (based on the data sheet). Please let me know if you need any more additional information or clarity and I will be happy to provide it.

  Read the article

• Windows 7 booting and startup repair issues

  - by aardvark

  I have a MSI FR720 laptop with Windows 7 and Lubuntu partions. For quite a while (6 months or so) I've been having issues booting from my hard drive, it'd take me between 5 minutes and several hours for me to be able to have it recognize the hard drive as a bootable device. I did several disk checks on it, and my hard drive seems in perfect condition, and the fact that booting would usually only work after removing the hard drive and trying to reset it in its slot or lightly shaking it makes me think it had something to do with the connection in the hard drive slot as opposed to the hard drive itself. I was having particular issues with it detecting the hard drive today so I decided to try booting it from an external hard drive dock. It detected it first try and so far has had no problems finding the bootable partitions on my hard drive. When I selected my Windows 7 partition from the boot menu it said that it hadn't been shut down properly last time and needed startup repair. I've done this several times over the last 6 months, so this is hardly unusual. I do startup repair, it fails, and then I try to do a system restore. The system restore also failed, and it says that no files were changed. I restart and try it again. However, this time when I get to the startup repair it's not detecting a Windows OS. I tried clicking next and doing a startup repair but the repair is always failing. If I ignore the startup repair option and instead select "Launch windows normally" it will get to the windows animation, stop halfway through and then crash into a BSoD. I can't read the error on the screen because it immediately switches to back and tries to restart. This is my first time asking a question like this online, so let me know if I need to provide any extra information and I'll do my best to give it I tried using diskpart to find the list of partitions and see if one's labelled as an active partition, but it says that no disk were detected. I can run Lubuntu just fine. I can also see all of my Windows 7 files from it EDIT: The startup repair diagnosis and repair log is this: -- Number of repair attempts: 1 Session details System Disk = Windows directory = AutoChk Run = 0 Number of root causes = 1 Test Performed: Name: Check for updates Result: Completed successfully. Error code = 0x0 Time taken = 15ms Test Performed: Name: System disk test Result: Completed successfully. Error code = 0x0 Time taken = 31ms Root cause found. If a hard disk is installed, it is not responding. -- Any chance that this is a result of me doing this through an external dock through a USB drive?

  Read the article

• 2 servers, high availability and faster response

  - by user17886

  I recently bought a second webserver because I worry about hardware failure of my old server. Now that I have that second server I wish to do a little more then just have one server standby and replicate all day. As long as it's there I might as well get some advantage our of it ! I have a website powered by ubuntu 12.04, nginx, php-fpm, apc, mysql (5.5) and couchdb. Im currently testing configurations where i can achieve failover AND make good use of the extra harware for faster responses / distributed load. The setup I am testing nowinvolves heartbeat for ip failover and two identical servers. Of the two servers only one has a public ip adress. If one server crashes the other server takes over the public ip adress. On an incoming request nginx forwards the request tot php-fpm to either server a of server b (50/50 if both servers are alive). Once the request has been send to php-fpm both servers look at localhost for the mysql server. I use master-master mysql replication for this. The file system is synced with lsyncd. This works pretty well but Im reading it's discouraged by the (mysql) community. Another option I could think of is to use one server as a mysql master and one server as a web/php server. The servers would still sync their filesystem, would still run the same duplicate software (nginx,mysql) but master slave mysql replication could be used. As long as bother servers are alive I could just prefer nginx to listen to ip a and mysql to ip b. If one server is down, the other server could take over the task of the other server, simply by ip switching. But im completely new at this so I would greatly value your expert advice. Is either of the two setups any good ? If you have any thoughts on this please let me know ! PS, virtualisation, hosting on different locations or active/passive setups are not solutions im looking for. I find virtual server either too slow or too expensive. I already have a passive failover on another location. But in case of a crash I found the site was still unreachable for too long due to dns caching.

  Read the article

• HttpWebRequest and Ignoring SSL Certificate Errors

  - by Rick Strahl

  Man I can't believe this. I'm still mucking around with OFX servers and it drives me absolutely crazy how some these servers are just so unbelievably misconfigured. I've recently hit three different 3 major brokerages which fail HTTP validation with bad or corrupt certificates at least according to the .NET WebRequest class. What's somewhat odd here though is that WinInet seems to find no issue with these servers - it's only .NET's Http client that's ultra finicky. So the question then becomes how do you tell HttpWebRequest to ignore certificate errors? In WinInet there used to be a host of flags to do this, but it's not quite so easy with WebRequest. Basically you need to configure the CertificatePolicy on the ServicePointManager by creating a custom policy. Not exactly trivial. Here's the code to hook it up: public bool CreateWebRequestObject(string Url) {    try     {        this.WebRequest =  (HttpWebRequest) System.Net.WebRequest.Create(Url);         if (this.IgnoreCertificateErrors)            ServicePointManager.CertificatePolicy = delegate { return true; };}One thing to watch out for is that this an application global setting. There's one global ServicePointManager and once you set this value any subsequent requests will inherit this policy as well, which may or may not be what you want. So it's probably a good idea to set the policy when the app starts and leave it be - otherwise you may run into odd behavior in some situations especially in multi-thread situations.Another way to deal with this is in you application .config file. Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} <configuration>   <system.net>     <settings>       <servicePointManager           checkCertificateName="false"           checkCertificateRevocationList="false"                />     </settings>   </system.net> </configuration> This seems to work most of the time, although I've seen some situations where it doesn't, but where the code implementation works which is frustrating. The .config settings aren't as inclusive as the programmatic code that can ignore any and all cert errors - shrug. Anyway, the code approach got me past the stopper issue. It still amazes me that theses OFX servers even require this. After all this is financial data we're talking about here. The last thing I want to do is disable extra checks on the certificates. Well I guess I shouldn't be surprised - these are the same companies that apparently don't believe in XML enough to generate valid XML (or even valid SGML for that matter)...© Rick Strahl, West Wind Technologies, 2005-2011Posted in .NET  CSharp  HTTP  

  Read the article

• Map a Network Drive from XP to Windows 7

  - by Mysticgeek

  We’ve received a lot of questions about mapping a drive from XP to Windows 7 to access data easily. Today we look at how to map a drive in Windows 7, and how to map to an XP drive from Windows 7. With the new Homegroup feature in Windows 7, it makes sharing data between computers a lot easier. But you might need to map a network drive so you can go directly into a folder to access its contents. Mapping a network drive may sound like “IT talk”, but the process is fairly easy. Map Network Drive in Windows 7 Note: All of the computers used in this article are part of the same workgroup on a home network. In this first example we’re mapping to another Windows 7 drive on the network. Open Computer and from the toolbar click on Map Network Drive. Alternately in Computer you can hit “Alt+T” to pull up the toolbar and click on Tools \ Map Network Drive. Now give it an available drive letter, type in the path or browse to the folder you want to map to. Check the box next to Reconnect at logon if you want it available after a reboot, and click Finish. If both machines aren’t part of the same Homegroup, you may be prompted to enter in a username and password. Make sure and check the box next to Remember my credentials if you don’t want to log in every time to access it. The drive will map and the contents of the folder will open up. When you look in Computer, you’ll see the drive under network location. This process works if you want to connect to a server drive as well. In this example we map to a Home Server drive. Map an XP Drive to Windows 7 There might be times when you need to map a drive on an XP machine on your network. There are extra steps you’ll need to take to make it work however. Here we take a look at the problem you’ll encounter when trying to map to an XP machine if things aren’t set up correctly. If you try to browse to your XP machine you’ll see a message that you don’t have permission. Or if you try to enter in the path directly, you’ll be prompted for a username and password, and the annoyance is, no matter what credentials you put in, you can’t connect. To solve the problem we need to set up the Windows 7 machine as a user on the XP machine and make them part of the Administrators group. Right-click My Computer and select Manage. Under Computer Management expand Local Users and Groups and click on the Users folder. Right-click an empty area and click New User. Add in the user credentials, uncheck User must change password at next logon, then check Password never expires then click Create. Now you see the new user you created in the list. After the user is added you might want to reboot before proceeding to the next step.   Next we need to make the user part of the Administrators group. So go back into Computer Management \ Local Users and Groups \ Groups then double click on Administrators. Click the Add button in Administrators Properties window. Enter in the new user you created and click OK. An easy way to do this is to enter the name of the user you created then click Check Names and the path will be entered in for you. Now you see the user as a member of the Administrators group. Back on the Windows 7 machine we’ll start the process of mapping a drive. Here we’re browsing to the XP Media Center Edition machine. Now we can enter in the user name and password we just created. If you only want to access specific shared folders on the XP machine you can browse to them. Or if you want to map to the entire drive, enter in the drive path where in this example it’s “\\XPMCE\C$” –Don’t forget the “$” sign after the local drive letter. Then login… Again the contents of the drive will open up for you to access. Here you can see we have two drives mapped. One to another Windows 7 machine on the network, and the other one to the XP computer.   If you ever want to disconnect a drive, just right-click on it and then Disconnect. There are several scenarios where you might want to map a drive in Windows 7 to access specific data. It takes a little bit of work but you can map to an XP drive from Windows 7 as well. This comes in handy where you have a network with different versions of Windows running on it. Similar Articles Productive Geek Tips Find Your Missing USB Drive on Windows XPMake Vista Index Your Network ConnectionsEasily Backup & Import Your Wireless Network Settings in Windows 7Quickly Open Network Connections List in Windows 7 or VistaHow To Find Drives Easily with Desk Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Kill Processes Quickly with Process Assassin Need to Come Up with a Good Name? Try Wordoid StockFox puts a Lightweight Stock Ticker in your Statusbar Explore Google Public Data Visually The Ultimate Excel Cheatsheet Convert the Quick Launch Bar into a Super Application Launcher

  Read the article

• Geek Fun: Virtualized Old School Windows – Windows 95

  - by Matthew Guay

  Last week we enjoyed looking at Windows 3.1 running in VMware Player on Windows 7.  Today, let’s upgrade our 3.1 to 95, and get a look at how most of us remember Windows from the 90’s. In this demo, we’re running the first release of Windows 95 (version 4.00.950) in VMware Player 3.0 running on Windows 7 x64.  For fun, we ran the 95 upgrade on the 3.1 virtual machine we built last week. Windows 95 So let’s get started.  Here’s the first setup screen.  For the record, Windows 95 installed in about 15 minutes or less in VMware in our test. Strangely, Windows 95 offered several installation choices.  They actually let you choose what extra parts of Windows to install if you wished.  Oh, and who wants to run Windows 95 on your “Portable Computer”?  Most smartphones today are more powerful than the “portable computers” of 95. Your productivity may vastly increase if you run Windows 95.  Anyone want to switch? No, I don’t want to restart … I want to use my computer! Welcome to Windows 95!  Hey, did you know you can launch programs from the Start button? Our quick spin around Windows 95 reminded us why Windows got such a bad reputation in the ‘90’s for being unstable.  We didn’t even get our test copy fully booted after installation before we saw our first error screen.  Windows in space … was that the most popular screensaver in Windows 95, or was it just me? Hello Windows 3.1!  The UI was still outdated in some spots.   Ah, yes, Media Player before it got 101 features to compete with iTunes. But, you couldn’t even play CDs in Media Player.  Actually, CD player was one program I used almost daily in Windows 95 back in the day. Want some new programs?  This help file about new programs designed for Windows 95 lists a lot of outdated names in tech.    And, you really may want some programs.  The first edition of Windows 95 didn’t even ship with Internet Explorer.   We’ve still got Minesweeper, though! My Computer had really limited functionality, and by default opened everything in a new window.  Double click on C:, and it opens in a new window.  Ugh. But Explorer is a bit more like more modern versions. Hey, look, Start menu search!  If only it found the files you were looking for… Now I’m feeling old … this shutdown screen brought back so many memories … of shutdowns that wouldn’t shut down! But, you still have to turn off your computer.  I wonder how many old monitors had these words burned into them? So there’s yet another trip down Windows memory lane.  Most of us can remember using Windows 95, so let us know your favorite (or worst) memory of it!  At least we can all be thankful for our modern computers and operating systems today, right?  Similar Articles Productive Geek Tips Geek Fun: Remember the Old-School SkiFree Game?Geek Fun: Virtualized old school Windows 3.11Stupid Geek Tricks: Tile or Cascade Multiple Windows in Windows 7Stupid Geek Tricks: Select Multiple Windows on the TaskbarHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

  Read the article

• Geek Fun: Virtualized Old School Windows – Windows 95

  - by Matthew Guay

  Last week we enjoyed looking at Windows 3.1 running in VMware Player on Windows 7.  Today, let’s upgrade our 3.1 to 95, and get a look at how most of us remember Windows from the 90’s. In this demo, we’re running the first release of Windows 95 (version 4.00.950) in VMware Player 3.0 running on Windows 7 x64.  For fun, we ran the 95 upgrade on the 3.1 virtual machine we built last week. Windows 95 So let’s get started.  Here’s the first setup screen.  For the record, Windows 95 installed in about 15 minutes or less in VMware in our test. Strangely, Windows 95 offered several installation choices.  They actually let you choose what extra parts of Windows to install if you wished.  Oh, and who wants to run Windows 95 on your “Portable Computer”?  Most smartphones today are more powerful than the “portable computers” of 95. Your productivity may vastly increase if you run Windows 95.  Anyone want to switch? No, I don’t want to restart … I want to use my computer! Welcome to Windows 95!  Hey, did you know you can launch programs from the Start button? Our quick spin around Windows 95 reminded us why Windows got such a bad reputation in the ‘90’s for being unstable.  We didn’t even get our test copy fully booted after installation before we saw our first error screen.  Windows in space … was that the most popular screensaver in Windows 95, or was it just me? Hello Windows 3.1!  The UI was still outdated in some spots.   Ah, yes, Media Player before it got 101 features to compete with iTunes. But, you couldn’t even play CDs in Media Player.  Actually, CD player was one program I used almost daily in Windows 95 back in the day. Want some new programs?  This help file about new programs designed for Windows 95 lists a lot of outdated names in tech.    And, you really may want some programs.  The first edition of Windows 95 didn’t even ship with Internet Explorer.   We’ve still got Minesweeper, though! My Computer had really limited functionality, and by default opened everything in a new window.  Double click on C:, and it opens in a new window.  Ugh. But Explorer is a bit more like more modern versions. Hey, look, Start menu search!  If only it found the files you were looking for… Now I’m feeling old … this shutdown screen brought back so many memories … of shutdowns that wouldn’t shut down! But, you still have to turn off your computer.  I wonder how many old monitors had these words burned into them? So there’s yet another trip down Windows memory lane.  Most of us can remember using Windows 95, so let us know your favorite (or worst) memory of it!  At least we can all be thankful for our modern computers and operating systems today, right?  Similar Articles Productive Geek Tips Geek Fun: Remember the Old-School SkiFree Game?Geek Fun: Virtualized old school Windows 3.11Stupid Geek Tricks: Tile or Cascade Multiple Windows in Windows 7Stupid Geek Tricks: Select Multiple Windows on the TaskbarHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

  Read the article

• Creating packages in code – Execute SQL Task

  The Execute SQL Task is for obvious reasons very well used, so I thought if you are building packages in code the chances are you will be using it. Using the task basic features of the task are quite straightforward, add the task and set some properties, just like any other. When you start interacting with variables though it can be a little harder to grasp so these samples should see you through. Some of these more advanced features are explained in much more detail in our ever popular post The Execute SQL Task, here I’ll just be showing you how to implement them in code. The abbreviated code blocks below demonstrate the different features of the task. The complete code has been encapsulated into a sample class which you can download (ExecSqlPackage.cs). Each feature described has its own method in the sample class which is mentioned after the code block. This first sample just shows adding the task, setting the basic properties for a connection and of course an SQL statement. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, "localhost", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Set required properties taskHost.Properties["Connection"].SetValue(taskHost, sqlConnection.ID); taskHost.Properties["SqlStatementSource"].SetValue(taskHost, "SELECT * FROM sysobjects"); For the full version of this code, see the CreatePackage method in the sample class. The AddSqlConnection method is a helper method that adds an OLE-DB connection to the package, it is of course in the sample class file too. Returning a single value with a Result Set The following sample takes a different approach, getting a reference to the ExecuteSQLTask object task itself, rather than just using the non-specific TaskHost as above. Whilst it means we need to add an extra reference to our project (Microsoft.SqlServer.SQLTask) it makes coding much easier as we have compile time validation of any property and types we use. For the more complex properties that is very valuable and saves a lot of time during development. The query has also been changed to return a single value, one row and one column. The sample shows how we can return that value into a variable, which we also add to our package in the code. To do this manually you would set the Result Set property on the General page to Single Row and map the variable on the Result Set page in the editor. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, "localhost", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Add variable to hold result value package.Variables.Add("Variable", false, "User", 0); // Get the task object ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask; // Set core properties task.Connection = sqlConnection.Name; task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = 'sysrowsets'"; // Set single row result set task.ResultSetType = ResultSetType.ResultSetType_SingleRow; // Add result set binding, map the id column to variable task.ResultSetBindings.Add(); IDTSResultBinding resultBinding = task.ResultSetBindings.GetBinding(0); resultBinding.ResultName = "id"; resultBinding.DtsVariableName = "User::Variable"; For the full version of this code, see the CreatePackageResultVariable method in the sample class. The other types of Result Set behaviour are just a variation on this theme, set the property and map the result binding as required. Parameter Mapping for SQL Statements This final example uses a parameterised SQL statement, with the coming from a variable. The syntax varies slightly between connection types, as explained in the Working with Parameters and Return Codes in the Execute SQL Taskhelp topic, but OLE-DB is the most commonly used, for which a question mark is the parameter value placeholder. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, ".", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Get the task object ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask; // Set core properties task.Connection = sqlConnection.Name; task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = ?"; // Add variable to hold parameter value package.Variables.Add("Variable", false, "User", "sysrowsets"); // Add input parameter binding task.ParameterBindings.Add(); IDTSParameterBinding parameterBinding = task.ParameterBindings.GetBinding(0); parameterBinding.DtsVariableName = "User::Variable"; parameterBinding.ParameterDirection = ParameterDirections.Input; parameterBinding.DataType = (int)OleDBDataTypes.VARCHAR; parameterBinding.ParameterName = "0"; parameterBinding.ParameterSize = 255; For the full version of this code, see the CreatePackageParameterVariable method in the sample class. You’ll notice the data type has to be specified for the parameter IDTSParameterBinding .DataType Property, and these type codes are connection specific too. My enumeration I wrote several years ago is shown below was probably done by reverse engineering a package and also the API header file, but I recently found a very handy post that covers more connections as well for exactly this, Setting the DataType of IDTSParameterBinding objects (Execute SQL Task). /// <summary> /// Enumeration of OLE-DB types, used when mapping OLE-DB parameters. /// </summary> private enum OleDBDataTypes { BYTE = 0x11, CURRENCY = 6, DATE = 7, DB_VARNUMERIC = 0x8b, DBDATE = 0x85, DBTIME = 0x86, DBTIMESTAMP = 0x87, DECIMAL = 14, DOUBLE = 5, FILETIME = 0x40, FLOAT = 4, GUID = 0x48, LARGE_INTEGER = 20, LONG = 3, NULL = 1, NUMERIC = 0x83, NVARCHAR = 130, SHORT = 2, SIGNEDCHAR = 0x10, ULARGE_INTEGER = 0x15, ULONG = 0x13, USHORT = 0x12, VARCHAR = 0x81, VARIANT_BOOL = 11 } Download Sample code ExecSqlPackage.cs (10KB)

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >