Search Results

Search found 7114 results on 285 pages for 'hope'.

Page 176/285 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• Single m0n0wall - Two LAN Subnets - How To Setup

  - by SnAzBaZ

  I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

  Read the article

• Configure a Windows PC as network appliance w/o monitor, keyboard and mouse

  - by Joshua Lim

  I intend to use a small form factor PC with Windows 7 Professional installed as a network appliance attached directly to my customer's LAN without connecting a monitor, keyboard or mouse. How should I configure the networking for my PC so that I can access it via say my laptop? I figure that I can do it 2 ways. Attach my laptop to the PC using a crossover cable? Connect via RDP and configure networking. Configure an IP address on the PC before I deliver it to the customer place. At the customer's place, attach the PC to LAN and connect to the IP address which I previously configured from my laptop or from one of the customer's workstations. I know the first way is doable, but is the second way possible? I'm sorry if this question sounds ridiculous - I am Delphi programmer but a novice on networking. Finally, if possible, I hope to make the configuration process web based as I wouldn't like to reveal the fact that I am using Win7 Pro for the network appliance!

  Read the article

• How to set up a PRIVATE vimwiki on Dropbox.com

  - by Zongheng Yang

  Hi everyone, I assume those who are reading this page know what vimwiki and dropbox.com are and what they are for, so I might directly go into my confusion. The common way of setting a PRIVATE vimwiki on dropbox is simply let your vimwiki directories be under Dropbox folder (but not Dropbox/Public/ because it would be PUBLIC). Dropbox allows directly viewing html with dropbox.com/* url: for example a index.html can be accessed by url https://dl-web.dropbox.com/get/Wiki/html/index.html?w=bfead71a, being added after the file name a specified string, ?w=bfead71a. Hence, if inside index.html there is reference to A.html, which is located in the same folder index.html is in, it has to be accessed using some url like https://dl-web.dropbox.com/get/Wiki/html/index.html?w=SPECIFIED_STRING. But it is seemingly impossible to hack vimwiki in order to make the hrefs in converted htmls corrected in this way. Is there some approach that can resolve this problem? I hope I make myself clear. Had you any questions, please ask me for further explanations. Thank you!

  Read the article

• IIS 7.5 truncating POST body containing JSON data with ASP.NET MVC 3

  - by Guneet Sahai

  I'm facing a problem which I hope is a configuration thing with IIS but is right now giving a lot of trouble. Basically I have a controller that accepts a JSON and does some processing. While it generally works fine, but every now and then when the system has some load I get an error. After some painful debugging, we figured the incoming JSON gets truncated which causes the deserialzer to fail. To narrow down the problem - we wrote a simple controller that accepts a JSON and tries to deserialize it. In case it fails it just logs it. This works fine but when I hit it using a load testing tool (JMeter) it throws the same error (truncation) for a few requests. The # of failures increased when I increase parallel connections. It starts showing with 150 concurrent requests. We are running IIS 7 on windows 2008 server with ASP.Net MVC 3 with more or less default configuration of IIS. More information available in my question below http://stackoverflow.com/questions/12662282/content-length-of-http-request-body-size

  Read the article

• Strange 400 error with IIS 7.5 and a webservice?

  - by Juw

  Ok, this is a longshot. I have been pondering this for hours. I have no clue how to solve this. But maybe someone here can recognize the problem and point me to right direction. I have an IIS 7.5 server and a MSSQL database on a different server. On the IIS server there is a webservice that communicates with the MSSQL server. The problem is that when there is data that the MSSQL server needs to send back to the webservice and the webservice delivers that back to the webbrowser (JSON) i get a 400 error. Looking through the logs for the IIS there is just a 400....nothing more. When i put in a call to the service in my browsers URL field i get this: "The server encountered an error processing the request. Please see the service help page for constructing valid requests to the service." There is NOTHING wrong with how i call the webservice. It has worked before on a different server (a dev server). Do someone have a clue on what this can be about? 400 means malformed URL...it isn´t. And why is that when there are no data to return to the user...everything works. But when there is data fetched from the MSSQL DB...the 400 error shows up. Hope someone have some tips how to solve it. Thanx in advance.

  Read the article

• Understanding Authorized Access to your Google Account

  - by firebush

  I'm having trouble understanding what I'm am granting to sites when they have "Authorized Access to my Google Account." This is how I see what has authorized access: Log into gmail. Click on the link that is my name in the upper-right corner, and from the drop-down select Account. From the list of links to the left, select Security. Click on Edit next to Authorized applications and sites. Authenticate again. At the top of the page, I see a set of sites that have authorized access to my account in various ways. I'm having trouble finding out information about what is being told to me here. There's no "help" link anywhere on the page and my Google searches are coming up unproductive. From the looks of what I see there, Google has access to my Google calendar. I feel comfortable about that, I think. But other sites have authorization to "Sign in using your Google account". My question is, what exactly does that authorization mean? What do the sites that have authorization to "Sign in using my Google account" have the power to do? I hope that this simply means that they authorize using the same criterion that gmail does. I assume that this doesn't grant them the ability to access my email. Can someone please calm my paranoia by describing (or simply pointing me to a site that describes) what these terms mean exactly? Also, if you have any thoughts about the safety of this feature, please share. Thanks!

  Read the article

• Implementing an isolated guest WLAN via IPSec VPN on Windows

  - by sysadmin1138

  We are attempting to set up a guest WLAN network that is isolated from the rest of our network. This is proving difficult due to a couple of technical reasons. My first choice was to use a separate VLAN, on which our Firewall's handy WLAN port would handle DHCP, DNS and the network isolation we need. Unfortunately, due to the fact that our main office and our Internet connection itself are in different locations connected by way of a Metro Ethernet connection, I'm at the mercy of our ISP for VLAN transit. They won't pass a second VLAN between our two sites. And my hardware doesn't support 802.1ad "Q-in-Q", which would also solve this problem. So I can't use the VLAN method for isolation. At least not without spending money. As our Firewall can handle IPSec site-to-site VPN connections, I hope it is possible to connect a Server 2008R2 (standard) server I have in the office location to the WLAN and provide gateway services to the firewall. Thusly: Unfortunately, I don't know if it is possible to connect the two this way. The firewall has a pretty flexible IPSec/L2TP implementation (I've used it to connect iPads in the wild), but is neither Kerberized or supports NTLM. The Connection Security Rules view on the Windows server seems to get close to what I think needs to be done, but I'm failing on figuring out how to get it to do what I need it to do. Is this even possible, or do I need to pursue alternate solution?

  Read the article

• Windows is very slow with my new SSD

  - by Maksym H.

  I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

  Read the article

• Setting up ssh config file with id_rsa through tunnel

  - by Rubens

  I've been struggling to set up a valid configuration to open a connection with a second machine, passing through another one, and using an id_rsa (which requests me a password) to connect to the third machine. I've asked this question in another forum, but I've received no answer that could be considered very helpful. The problem, better described, goes as follows: Local machine: user1@localhost Intermediary machine: user1@inter Remote target: user2@final I'm able to do the entire connection using pseudo-tty: ssh -t inter ssh user2@final (this will ask me the password for the id_rsa file I have in machine "inter") However, for speeding things up, I'd like to set my .ssh/config file, so that I can simply connect to machine "final" using: ssh final What I've got so far -- which does not work -- is, in my .ssh/config file: Host inter User user1 HostName inter.com IdentityFile ~/.ssh/id_rsa Host final User user2 HostName final.com IdentityFile ~/.ssh/id_rsa_2 ProxyCommand ssh inter nc %h %p The id_rsa file is used to connect to the middle machine (this requires me no password typing), and id_rsa_2 file is used to connect to machine "final" (this one requests a password). I've tried mixing up some LocalForward and/or RemoteForward fields, and putting the id_rsa files in both first and second machines, but I could not seem to succeed with no configuration whatsoever. Hope somebody can help me here! Regards! P.S.: the thread I've tried to get some help from: http://www.linuxquestions.org/questions/linux-general-1/proxycommand-on-ssh-config-file-4175433750/

  Read the article

• Undeliverable e-mail message from [email protected]

  - by QGfisher

  I am responsible for IT for a small charity and we have a problem with a few individuals who e-mail us on our hosted e-mail addresses. The individual is on btconnect and our server is also on BT broadband and using MSExchange. I understand that the message from [email protected] are generated by Exchange but can't tell whether this is a problem with our server (seems unlikely as most people send and receive e-mails perfectly well) or with the sender's server. I have copied a sample test message below and would be very grateful if somebody can explain what is causing this problem. I have * the personal details - hope that's acceptable but I don't want to compromise the individual's identity/security. ----- Original Message ----- From: "System Administrator" To: "****" <****.***@btconnect.com Sent: Tuesday, April 06, 2010 3:26 PM Subject: Undeliverable: Test Message Your message To: ***** Subject: Test Message Sent: Tue, 6 Apr 2010 15:25:59 +0100 did not reach the following recipient(s): ***@quiltersguild.org.uk on Tue, 6 Apr 2010 15:26:07 +0100 The e-mail account does not exist at the organization this message was sent to. Check the e-mail address, or contact the recipient directly to find out the correct address.

  Read the article

• configure a Macbook Pro to use external monitor at boot (Debian Linux)

  - by Eric

  In the spirit of reuse, I've installed Debian (version 6.0.5 "squeeze") on my wife’s old Macbook Pro (circa 2009 or so), to repurpose it for various tasks. The catch is the display is flaky. It will last a random amount of time, between 2 minutes and 2 hours, before freezing and graying out. This is a known issue with that generation of MBP. Fortunately it’s no problem for me, as I plan to use it with an external monitor anyway. Which brings us to the problem: How do I configure this thing to output to the external display by default, and hopefully disable the built-in LCD? The ideal solution would be to modify a setting in the EFI (BIOS), but I’m not holding out much hope for that. Next best thing would be a kernel option I can pass to the NVIDIA driver. What won’t work is a solution that doesn’t give me a display until X starts. I need to have console access, especially given that the built-in LCD is dying, and any day now might give out completely. So far I haven’t been able to find anything online. lspci says I’ve got an NVIDIA GeForce 9400M Help is much appreciated! Eric PS if this question is better suited to the Unix & Linux area, pls advise and I will move it.

  Read the article

• How to connect 2 routers (Asmax and D-link)

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• CIFS Mounting Permissions

  - by malco

  I have an issue that I;m going round in circles with, I hope you can help. The Set up: Server 1 (CIFS Client) - CentOS 6.3 AD integrated uing Samba/Winbind & idmap_ad Server 2 (CIFS Server) - CentOS 6.3 AD integrated uing Samba/Winbind & idmap_ad All users (apart from root) are AD authenticated and this, including groups, etc works happily. What's working: I have created a share on Server 2: [share2] path = /srv/samba/share2 writeable = yes Permissions on the share: drwxrwx---. 2 root domain users 4096 Oct 12 09:21 share2 I can log into a Windows machine as user5 (member of domain users) and everything works as it should, for example: If I create a file it shows the correct permissions and attributes on both the MS and the Linux sides. Where I Fall Down: I mount the share on Server 1 using: # mount //server2/share2 /mnt/share2/ -o username=cifsmount,password=blah,domain=blah Or using fstab: //server2/share2 /mnt/share2 cifs credentials=/blah/.creds 0 0 This mounts fine, but.... If I log su, or log onto server 1 as a normal user (say user5) and try to create a file I get: #touch test touch test touch: cannot touch `test': Permission denied Then if I check the folder the file was created but as the cifsmount user: -rw-r--r--. 1 cifsmount domain users 0 Oct 12 09:21 test I can rename, delete, move or copy stuff around as user5, I just can't create anything, what am I doing wrong? I'm guessing it's something to do with the mount action as when I log onto server2 as user5 and access the folder locally it all works as it should. Can anyone point me in the right direction?

  Read the article

• Rebuilding LVM after RAID recovery

  - by Xiong Chiamiov

  I have 4 disks RAID-5ed to create md0, and another 4 disks RAID-5ed to create md1. These are then combined via LVM to create one partition. There was a power outage while I was gone, and when I got back, it looked like one of the disks in md1 was out of sync - mdadm kept claiming that it only could find 3 of the 4 drives. The only thing I could do to get anything to happen was to use mdadm --create on those four disks, then let it rebuild the array. This seemed like a bad idea to me, but none of the stuff I had was critical (although it'd take a while to get it all back), and a thread somewhere claimed that this would fix things. If this trashed all of my data, then I suppose you can stop reading and just tell me that. After waiting four hours for the array to rebuild, md1 looked fine (I guess), but the lvm was complaining about not being able to find a device with the correct UUID, presumably because md1 changed UUIDs. I used the pvcreate and vgcfgrestore commands as documented here. Attempting to run an lvchange -a y on it, however, gives me a resume ioctl failed message. Is there any hope for me to recover my data, or have I completely mucked it up?

  Read the article

• Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

  - by Paul Taylor

  I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

  Read the article

• Office Compatibility Pack and File Permissions

  - by hymie

  MS isn't my thing, so I hope somebody can give me a pointer. We have a Windows domain, with a Server-2003-SP1-Enterprise file server. One of the specific files is a MS Excel 2007 (XLSX) file created by user LK. In the "Security" preferences setting, about a half-dozen users (including me) have access to this file. LK is the owner and has "full control", while the rest of us have "Read" , "Read & Execute", and "Write" permission. LK is also the owner of the directory that this file resides in. I don't know if that's relevant. So far so good. My desktop machine has Windows XP SP3 , and Excel 2003 SP3 , and the "Office Compatibility Pack" which lets me read and write the new XLSX files. However, whenever I write the file, the permissions are changed. The newly-written file only has permissions for LK and me, and both are "Full control" So in short, what am I doing wrong, and how should I set this up to do it right, keeping the permissions on the file that were there when I started?

  Read the article

• esx5 debian VM vlan setup

  - by Kstro21

  i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

  Read the article

• Generic/Text Printer on Windows 7 not prompting for file name

  - by Trevor Tippins

  Hope someone can shed some light on this. I am downloading reports from an AIX-based system by directing them to a TT printer which the terminal emulator (MultiView 2000) intercepts and directs to the default printer on the local system. This local printer is configured as a vanilla Generic/Text printer attached to a FILE port. When I print from AIX, the output is spooled down and the local printer prompts for a file name into which to save the file...but not under Windows 7. This has worked fine for many years, on both Win2K and WinXP. However, on Windows 7 the output gets spooled as a file into spool\PRINTERS (and looks as expected) but the print job then hangs with a status of "Error - Printing" and never prompts for a file name. I have to cancel the job. The Generic/Text printer works as expected with other applications. I have tried setting the printer to print directly rather than spooling but this only serves to hang the terminal session too. I've also tried to run the emulator in Windows 2000 Compatibility Mode and as Administrator in case it was something like that but with no luck. As you might expect, it does work fine in XP Mode (as long as I print to a printer defined therein and not the host's printer) but operationally this isn't going to be an option. Obviously this emulation software is a decade old (at least) and I could just cross/upgrade all the users (at a cost) but, before I do so, has anyone seen this sort of behaviour before and found some sort of fix? Remote OS: AIX 5 Client OS: Windows 7 Pro (32-bit) Printer: Generic/Text on a FILE port TE Software: MultiView 2000 (32-bit) Thanks in advance.

  Read the article

• Recover data from Dynamic Disk (MBR) bigger than 2TB

  - by Helder

  Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

  Read the article

• running a command as root with /bin/su and without gives different results

  - by n00bInCpp

  Some background: I have a machine with SLES 11 installed. I am running a bash script that one of its lines is /bin/su $USER -c SOME_CMD. Unfortunately, the SOME_CMD that comes after the -c keeps failing, no matter if USER=root or any different user. However, if /bin/su $USER -c part is omitted then everything runs smoothly. Moreover, I have run the script on RHEL5 and it worked fine. Anyway, my question is why does it happen? If it is a permissions problems then why when I run this as root with /bin/su and without I get different results? P.S. apologize if somebody else has asked it before, I have done many googling and got nothing that satisfies. Thanks in advance, n00bInCpp EDIT Okay, I figured it out, I hope so. Instead of running /bin/su I used /user/bin/sudo -u $MY_USER_1 MY_ENV_VAR="/home/user1" SOME_CMD. I don't understand why I have to use sudo, though. I am used to run a command as a different user using su and not worrying about permissions problems, but I guess it doesn't work like that on SLES 11/SuSE. Anyhow, thanks to everyone who wanted to or helped me.

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• no A record show in the answer section in dig results

  - by eric low

  To check the record for the domain, run dig with domain name as the parameter. dig example.com any I get the below result. Why there is no A record show in the result. What did i do wrong during the setup. Please advice what suppose to look into it. Hope everyone can help me to resolve the case asap. ; <<>> DiG 9.9.3-P2 <<>> example.com any ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 44674 ;; flags: qr rd ra; QUERY: 1, ANSWER: 8, AUTHORITY: 4, ADDITIONAL: 1 ;; OPT PSEUDOSECTION: ; EDNS: version: 0, flags:; udp: 4096 ;; QUESTION SECTION: ;example.com. IN ANY ;; ANSWER SECTION: example.com. 3489 IN MX 100 biz.mail.com. example.com. 3482 IN NS ns1.domain.com. example.com. 3482 IN NS ns2.domain.com. ;; AUTHORITY SECTION: example.com. 3482 IN NS ns2.domain.com. example.com. 3482 IN NS ns1.domain.com. ;; Query time: 0 msec ;; SERVER: xxx.252.xxx.xxx#53(xxx.252.xxx.xxx) ;; WHEN: Wed Oct 30 04:48:34 CDT 2013 ;; MSG SIZE rcvd: 349

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• How can I remedy the always-on-top window problem?

  - by GateKiller

  Sorry for the vague title but this one is hard to explain so bear with me please. I'm using Windows Vista at work for web development and sometimes when I Click or Alt-Tab to background window, the window will get focus but it will not be brought to the front. In order to bring the window to the front, I have to click on the applications border (when the resize cursor appears) and the window will then jump to the front. I've had this problem for about a year now and it happens at least a dozen times a day, but it doesn't do this all the time - seems random. I hope I have explained the issue fully (and you've understood it) and would appreciate any constructive answers or comments to solve this problem. Example: If I Alt-Tab from Google Chrome to Notepad and this problem randomly occurs, Google Chrome will remain in front of Notepad, however, I will be able to type text into Notepad while the window is behind Google Chrome. Clicking on Notepad's content area will not bring it to the front but clicking it's window border will. Video Exampe http://vimeo.com/19388998 In this video, I clicked from Google Chome to UltraEdit and chrome stayed in font, but as you can see, I can still type in UltraEdit. I'm starting to believe that this could be a bug in Google Chrome so I'll continue to watch if this between other applications.

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >