Search Results

Search found 5337 results on 214 pages for 'modal dialog'.

Page 176/214 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• ESXi 4.1 host not recognising existing VMFS datastore

  - by ThatGraemeGuy

  Existing setup: host1 and host2, ESX 4.0, 2 HBAs each. lun1 and lun2, 2 LUNs belonging to the same RAID set (my terminology might be sketchy here). This has been working just fine all along. I added host3, ESXi 4.1, 2 HBAs. If I view Configuration / Storage Adapters, I can see that both HBAs see both LUNs, but if I view Configuration / Storage, I only see 1 datastore. host1/2 can see both LUNs and I have VMs running on both too. I have rescanned, refreshed and even rebooted, but host3 refuses to acknowledge 1 of the datastores. Does anyone know what's going on? Update: I re-installed the host with ESX (not i) 4.0, same version as the existing hosts and it's still not recognising the vmfs. I think I'm going to SVmotion everything off that datastore then format it. Update2: I've created the LUN from scratch and the problem gets even weirder. I've presented the LUN to all 3 hosts, and I can see the LUN in the vSphere client's Configuration / Storage Adapters section on all 3 hosts. If I create a datastore on the LUN via the Configuration / Storage section on host1, it works fine and I can create an empty folder via datastore browser, but the datastore is not seen by the host2 and host3. I can use the Add Storage wizard on host2 and it will see the LUN. At this point the "VMFS Label" column has the label I gave with "(head)" appended. If I try the Add Storage wizard's "Keep the existing signature" option, it fails with an error "Cannot change the host configuration." and a dialog box that says 'Call "HostStorageSystem.ResolveMultipleUnresolvedVmfsVolumes" for object "storageSystem-17" on vCenter Server "vcenter.company.local" failed.' If I try the Add Storage wizard's "Assign a new signature" option on host2, it will complete and the VMFS label will have "snap-(hexnumber)-" prepended. At this point its also visible on host3, but not host1. I have a similar setup in a different datacenter which didn't give me all this trouble.

  Read the article

• Installing WindowsAuthentication breaks authentication / web.config?

  - by Ian Quigley

  I have a clean Windows 2008 R2 box (on a VM) and have installed IIS 7.5 with default options. I then copied a website to it (from Windows 7, IIS 7) and after a little tweaking the website is working fine. The website is currently using and working with Anonymous Authentication. I have gone back to the Windows Components/Sever Manager, Roles - Security and ticked and installed Windows Authentication. When I check my server in IIS (top level above sites) - Authentication, I see Anonymous Authentication (enabled) ASP.NET Impersonation (disabled) Forms Authentication (disbaled) Windows Authentication (enabled) When I check my default website - Authentication, I see as above but "Retrieving status" and an error dialog saying There was an error while performing this operation. Details: Filename c:\inetpub\wwwroot\screwturnwiki\web.config Line number: 96 Error: This configuration section cannot be used in this path. This happens when the section is being locked at the parent level. Locking is either by default (overriderModeDefault="Deny"), or set explicity by a location tag with overrideMode="Deny" or the legacy allowOverride="False". I have tried hand editing the web.config with no success. UN-installing Windows Authentication happily returns my site to working with Anonymous Authentication, and allows me to enable/disable these three options. FYI. I am using ScrewTurnWiki with the Active Directory plug in.

  Read the article

• Windows Media Center doesn't see my movies

  - by DrJekyll

  I am trying to configure my Windows Media Center (Windows 7 Ultimate). I selected folder with my movies and added it to the library, but when I went to the movies library, it says "There are no items in this library yet - Windows Media Center is searching for media files in the background...". I have all necessary codecs installed, Windows Media Player opens those movies correctly. When I right click on the file - Open with - Windows Media Center it also plays them without any problem. Any ideas why they don't appear in the libraries? Edit: Movies are coded with divx and xvid codecs and they have ".avi" extension. Windows doesn't have problems playing them. I told Media Center where the files are. I even pointed Windows Media Center to a folder with only one .avi file it still couldn't find anything there. (I have given it quiet some time, even though searching in the directory with only one file shouldn't take more than a few seconds.) When I add a folder with a lot of movies, I get a dialog box "You can wait while media is added or select OK to continue using Windows Media Center.".                                                                        At the end it says it added about 90 movies, but when I go to the libraries, it's still empty.

  Read the article

• Cannot find network path for computer in workgroup of home Windows XP PCs

  - by John Galt

  VMWare Workstation 6.5 is running as an app on a Windows Vista 64bit PC host. Thanks to Workstation we have 2 guest machines running: TerriVM and MattVM (both of these run Windows XP SP2). We are attempting to get virtual networking configured so we can access the files of both of these VM guest systems from other real PCs connected to this home network. We think we are close but we can't quite get it right... Here is what we've done so far: * On VM Workstation, we set "Host Virtual Network Mapping" to use VMnet0 with the setting "Bridge to an automatically chosen adapter". * On each VM guest (i.e. using Windows explorer on XP), we rightmouse on the C disk, click "Sharing" tab, set shareName to "C_Disk" and check both boxes labeled "Share this folder on the network" and "Allow network users to change my files". Symptoms: On "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \TerriVM\C_Disk and assign drive letter T. We see all the folders on this shared drive and can open files on them. So that is good. On same "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \MattVM\C_Disk and assign drive letter M. We get a message box "_The network path \mattvm\C_Disk could not be found_". Alternatively, we type just \mattvm\ into the Folder box and click "Browse" and get a dialog box where we drill down from "Entire Network" to "Microsoft Windows Network" to "Workgroup" where both TerriVM and MattVM are listed as computers on the network. Clicking the + sign next to MattVM gives an hourglass and never enables the OK button and I have to cancel. In summary, I think we've attempted to share both of these virtual machines using the same techniques and connect to them in similar fashion, but one connects properly and the other machine can be seen but no shared resources on it can be accessed. Can anyone suggest something possibly overlooked or something to try? Thanks so much in advance.

  Read the article

• Attempting to set up xampp and zend server on the same machine

  - by umbregachoong

  I am attempting to set up the zend server and xampp on the same machine but I am running into problems. I came across documentation on the zend site that said you cannot do this. However the folks over at apachefriends said you can. I have since discovered that I can run some of the zendframework examples within xampp by downloading the zendframework2 library and the skeleton app from git and I am doing this right now. However, I would like to know how to set them both up without having any conflicts both for the apache2 server and phpmyadmin. (One of the frustrating things is trying to load phpmyadmin in the deployment dialog by using the zpk tool in Zend). What I did in trying to set up both servers on windows 7 is as follows: First I have tried to set up the httpd conf files separately for each server, xampp running on port 8082 , and zend running on port 8088. At the time xampp would work, but zend server would not. This is after setting up the virtual host files separately for each server. Question 1: Where are the zend server error logs? Earlier, I was able to get both of them running configuring the xampp server httpd-conf file alone, however, I experienced problems with phpmyadmin even after configuring phpmyadmin on xampp to work on a different port other than 3306. Second question here: how to set up the two mysql phpmyadmin instances so they do not conflict with each other? Here is the xampp virtual host section: ##ServerAdmin [email protected] DocumentRoot "C:/xampp/htdocs/" ServerName localhost 8082 ##ServerAlias www.dummy-host.example.com ##ErrorLog "logs/dummy-host.example.com-error.log" ##CustomLog "logs/dummy-host.example.com-access.log" common Here is the zend virtual host section: DocumentRoot "C:\Program Files (x86)\Zend\Apache2/htdocs" ServerName localhost:8088 </VirtualHost> I have looked at this httpd.apache.org/docs/2.2/vhosts/ and this http://survivethedeepend.com/zendframeworkbook/en/1.0/creating.a.local.domain.using.apache.virtual.hosts but I am obviously doing something wrong here. I also have the java sdk running on this machine with tomcat and apache and I have no conflicts- too bad this is not the case for zend server and xampp Thanks umbre gachoong

  Read the article

• How do you do a keyword search the Services.msc (mmc) window in Windows 7?

  - by Warren P

  When you want to run a service, you have very limited capabilities, in all current Windows versions, as far as I can tell. I usually start Services by typing "services.msc" into the Start-Run box, on most versions of Windows, this works. I know how to click the "Name" column in the MMC view of Windows Services. If you know what the first few characters of a service name is, you can usually sort by the name, and type the prefix to scroll the list down (find Windows Search for example). This seems pretty weak to me, so I spent some time searching the interwebs for tools that do a better job of managing services. Usually I have a keyword that I know "fooWare" might be the keyword, and I need to find the (usually badly named) service and start it and stop it. This is often WAY too hard. The best I could do is "NET SERVICES" from the command line, and maybe add a grep in there, but that doesn't list every service, only a few of them. And the MMC snap-in in Win7 now has an Export List button, exporting to csv text file feature which I have used from time to time, to export and then search. I have thought of writing my own tool. I'm hoping a better "service manager" utility exists out there that sysadmins use. I'd like a search box at the top right corner, kind of the same way that the Add-Remove-Programs dialog in Win7 and Vista has a search facility. Does such a services utility exist out there?

  Read the article

• Diagnosing Microsoft SQL Server error 9001: The log for the database is not available.

  - by Scott Mitchell

  Over the weekend a website I run stopped functioning, recording the following error in the Event Viewer each time a request is made to the website: Event ID: 9001 The log for database 'database name' is not available. Check the event log for related error messages. Resolve any errors and restart the database. The website is hosted on a dedicated server, so I am able to RDP into the server and poke around. The LDF file for the database exists in the C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA folder, but attempting to do any work with the database from Management Studio results in a dialog box reporting the same error - 9001: The log for database is not available... This is the first time I've received this error, and I've been hosting this site (and others) on this dedicated web server for over two years now. It is my understanding that this error indicates a corrupt log file. I was able to get the website back online by Detaching the database and then restoring a backup from a couple days ago, but my concern is that this error is indicative of a more sinister problem, namely a hard drive failure. I emailed support at the web hosting company and this was their reply: There doesn't appear to be any other indications of the cause in the Event Log, so it's possible that the log was corrupted. Currently the memory's resources is at 87%, which also may have an impact but is unlikely. Can the log just "become corrupted?" My question: What are the next steps I should take to diagnose this problem? How can I determine if this is, indeed, a hardware problem? And if it is, are there any options beyond replacing the disk? Thanks

  Read the article

• Office 2010 Trusted Locations not working after restart

  - by Josh King

  In Excel 2010, on Windows XP, I am unable to open files - through the open dialog box - from a network drive. The sever has already been added to the Trusted Locations and now most security settings turned down or off. Excel will show "Downloading ..." on that status bar and a progress bar which doesn't progress. We have left Excel sitting in this state for 30+ minutes and no change. A similar problem occurs when saving files to network shares. If we use explorer to navigate to the files and double click them they open flawlessly. No add-ins are active. We also have this problem in Word 2010, but the server was not initially in the Trusted Locations. I added it and it worked until the PC was reset, it now exhibits the same issues as Excel where the server is in the Trusted locations but will not open files. I have tried removing the server from the Trusted Location in both applications, restarting the PC and re-adding them (testing before, after and in-between) and had no luck.

  Read the article

• How do I troubleshoot a problem syncing Google contacts to an iPad?

  - by Daryl Spitzer

  I use my MacBook Pro to sync content onto my wife's iPad. (She doesn't have a computer.) She doesn't want all my contacts from the Address Book app on my MBP. But she does want her Google contacts on her iPad. I've tried the following settings in iTunes: I created a group in my address book called "Claire's" (and put just a couple contacts in it), since if one enables "Sync Address Book Contacts" one either has to select "All" or at least one group. I've double-checked her email address in the dialog that comes up after pressing the "Configure" button. But after syncing, only the couple contacts in the "Claire's" group are in the Contacts app on her iPad. I've checked her Google contacts, and she has over 2000. For some reason they're not syncing. How do I find out why they're not? I looked to see if I could just use an app to do the sync on the iPad, but couldn't find one with good ratings. Do you have one to recommend so I can give up struggling with getting this working in iTunes?

  Read the article

• Windows XP: How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because this (empty) directory is still undeleteable: C:\1\2\Favorites\Wien\What To Do.. I'm guessing because of the ".." at the end, Windows (Explorer and cmd) can't deal with it: Here is what Explorer properties shows: Any ideas?

  Read the article

• Registry remotley hacked win 7 need help tracking the perp

  - by user577229

  I was writing some .VBS code at thhe office that would allow certain file extensions to be downloaded without a warning dialog on a w7x32 system. The system I was writing this on is in a lab on a segmented subnet. All web access is via a proxy server. The only means of accessing my machine is via the internet or from within the labs MSFT AD domain. While writing and testing my code I found a message of sorts. Upon refresing the registry to verify my code changed a dword, instead the message HELLO was written and visible in regedit where the dword value wass called for. I took a screen shot and proceeded to edit my code. This same weird behavior occurred last time I was writing registry code except on another internal server. I understand that remote registry access exists for windows systems. I will block this immediately once I return to the office. What I want to know is, can I trace who made this connection? How would I do this? I suspect the cause of this is the cause of other "odd" behaviors I'm experiencing at work such as losing control of my input director master control for over an hour and unchanged code that all of a sudden fails for no logical region. These failures occur at funny times, whenver I'm about to give a demonstration of my test code. I know this sounds crazy however knowledge of the registry component makes this believable. Once the registry can be accessed, the entire system is compromised. Any help or sanity checking is appreciated.

  Read the article

• Cannot set video resolution above 640x480 after installing Windows XP SP2

  - by waanders

  I've installed Windows XP SP2 on a computer (there was not SP at all). Now the display settings are set back to 640x480 and 4 bits colors. And I can't change it, it's the only option in Settings tab of the Display dialog of Windows. The screen look awful now, how can I solve this problem? UPDATE: Seems to be a problem with the video driver (thanks @Karan and @Hennes). I did run Speccy (PC-Wizard freezes the computer) and this is a part of the log file: Summary Operating System Microsoft Windows XP Professional 32-bit SP3 CPU Intel Celeron Willamette 0.18um Technology RAM 512 MB DDR @ 133MHz (2.5-3-3-6) Motherboard COMPAQ 0838h (FC-478) Graphics Standard Monitor (640x480@1Hz) Hard Drives 19.0GB Maxtor 2B020H1 (PATA) Optical Drives No optical disk drives detected Audio No audio card detected ... Graphics Monitor Name Standard Monitor on Current Resolution 640x480 pixels Work Resolution 640x450 pixels State enabled, primary Monitor Width 640 Monitor Height 480 Monitor BPP 4 bits per pixel Monitor Frequency 1 Hz Device \\.\DISPLAY1 OpenGL Version 1.1.0 Vendor Microsoft Corporation Renderer GDI Generic GLU Version 1.2.2.0 Microsoft Corporation Values GL_MAX_LIGHTS 8 GL_MAX_TEXTURE_SIZE 1024 GL_MAX_TEXTURE_STACK_DEPTH 10 GL Extensions GL_WIN_swap_hint GL_EXT_bgra GL_EXT_paletted_texture GL_EXT_bgra

  Read the article

• Cannot log into Windows XP Embedded after changing computer name

  - by bignis

  Hi everyone, I purchased a tablet pc running Windows XP Embedded. The tablet was used in a medical clinic on a domain. For illustrative purposes, say the computer name was "COMPLEXCOMPUTERNAME". There was an administrator account, so I changed the password on account "COMPLEXCOMPUTERNAME\Administrator" to a blank password. I logged out and logged in successfully with the blank administrator password when the log-in dialog said "Log in to COMPLEXCOMPUTERNAME (this computer)". Next I renamed the computer from COMPLEXCOMPUTERNAME to SIMPLECOMPUTERNAME, which required a reboot. I did so, and I can't log in anymore. The log in screen still just says "Log in to COMPLEXCOMPUTERNAME (this computer)", but the account "COMPLEXCOMPUTERNAME\Administrator" no longer works. I suspect that this is because the computer has been renamed to SIMPLECOMPUTERNAME and it can no longer find the account. The "Log in to" dropdown can't be typed in, so I can't change the computer name Windows is trying to log into. I fear that I'm stuck. Is there a way I can get Windows to log into the computer name that I chose? Thanks! -Mike

  Read the article

• Word 2007 won't run, tries to reinstall, fails with error 1402.

  - by eidylon

  Okay, this problem has been plaguing this computer for a while now. We tried googling, and none of the answers found helped to solve the problem. So, I am now posting the answer here for posterity. Office 2007 Home/Student edition was installed on the computer, running Vista (32-bit). One day, Word just up and stopped working. All the other programs continued to operate as expected. But every time you would click the icon for Word, it would pop up an install dialog, with a message reading "Preparing to install...". After a few minutes of the little progress bar going and going, it errors out, and gives error 1402, something to the effect of unable to access registry key HKEY_Local_Machine\Software\Classes\.wll\.... Searching around, every answer i found had to do with reassigning the permissions on this key, giving full rights to SYSTEM or to Everyone, and propagating the changes down to all sub-keys. When ever this was attempted though, it would tell us that we were unable to access the key due to permissions, even though we had run regedit as Administrator and are logged on with an administrative account. We also tried uninstalling Office and reinstalling it, as well as doing a repair install. Both these attempts also threw the same 1402 error. Also of note was that the executable for Word (winword.exe) was MIA and no longer to be found in the Office install directory.

  Read the article

• Is Cloud Print to blame for my inability to print?

  - by VarLogRant

  I have just moved to the Chrome beta (first 9.something and currently 10.0.648.127) on my Windows 7 64-bit machine, and my good web browsers (Firefox Beta and Chrome) can no longer print, and neither can Komodo Edit. The problem seems to have started when I tried to enable Google Cloud Print. Frustratingly, I can still print from IE 9 RC, and also from other machines in the office, which means the problem is entirely on this Windows machine. When I try to print from Chrome, first time I get the printer dialog, and once I click print, it waits, then pops up "Something went wrong", and each time after, it pops up with "No Printer Found". Under Firefox, I get "An unknown error occurred while printing", as does Komodo. I have printed from these applications before, and have even printed from Google Cloud Print. Once. But then it stopped. I really don't know where to go next in debugging this thing, and the Google results I see tend to be from 2007. I'm not ready for the paperless office yet, so please help!

  Read the article

• How to show "only number" in picture cross-reference in Word 2007 document?

  - by kornelijepetak

  I have many pictures in a document and I reference them very often in text. I don't want to lose the order so I am using Insert - Cross-reference. This opens the cross-reference dialog where I can set Reference type to Picture. For "Insert reference to", there are 5 choices: - Entire caption - Only label and number - Only caption text - Page number - Above/below What I need is a reference that would be inserted like this: [4], and not like this: [Picture 4]; None of these options enable me to do it. Is there any way to make Word 2007 insert a reference to only Caption Number? Note: The document is written in Croatian language which has 7 declension cases, so using "Picture 4" would not be valid in all cases. Actually caption label Picture is set to croatian word "Slika" and when I need to say say "in the picture" I can't because it would be "na Slici 5." and not "na Slika 5." (like Word would make me do). That's why I need to reference only the caption number. Is that possible in Word 2007?

  Read the article

• Can I run Excel 2010 on a server?

  - by Glen Little

  This question is not about a person using Excel on a computer that happens to have an Windows Server OS. And it is not about using any Sharepoint services features! The question is about automated processes that use code (Office Automation) to open Excel files, manipulate them, run calculations, read data, save copies of the file and close the files... all in code. In previous versions of Excel the licensing agreement prevented use on a public server, notes from Microsoft warned about the problems trying to use Office Automation in a server environment, and we were warned that Excel was single threaded and not designed for use on a server. Most of the articles about this were written before Office 2010. But now, Excel 2010 is designed to work on a High Performance Computing server using HPC Services for Excel. One HPC document mentions "Windows HPC Server 2008 R2 includes a comprehensive pop-up manager that can handle occasional dialog boxes and pop-up messages". So my question is... is it now "safe" to run code that automates Excel 2010 on a "normal" server without using the HPC services? If not, can the HPC Services for Excel work on a single server? I don't need the high performance, distributed computing, aspect of HPC Services for Excel... just the ability to run Excel on a server. Can that now be done? Thanks, Glen

  Read the article

• Eclipse on Ubuntu: Rectangles instead of Strings and some Java methods and classes

  - by Claus Hausberger

  after upgrading from Ubuntu 9.04. to 11.04 (new installation), I have weird problems with the Eclipse editor. With the Eclipse PyDev plugin, whenever I typ single quoted strings like 'bla', they appear as rectangles (both the quotes as well as the string). First I thought this was a problem with the PyDev plugin, but it also happens with Java and Scala Plugins. With Java, it happens, for example, when typing System.out.println("bla") and then "out" is shown as rectangles only. Weird is that for about half a second I see "System.out.println" and then the editor changes it to System.[][][].println (not really [] (here I used two brackets), it is shown as rectangles). This is very weird. I've never had this before with any Ubuntu, Java or Eclipse version. Currently, I use: Ubuntu 11.04. Eclipse 3.6 Java 1.6.0_25 The latest plugins for Python (2.1) and Scala (beta 5) where used. Eclipse and Ubuntu Terminal is set to UTF-8. The problem also happens when using KDE instead of Gnome. I doubt is has anything to do with Java as I use the same versions on older Ubuntu installations (10.04, 9.10, etc) at work. It does not happen with Netbeans. But I saw once error dialog message from the Update Manager where there were some rectangles in the error widget. Maybe this is the same problem Any ideas what could be wrong here and how to fix this? Eclipse is unusable but I need this for work and also for Scala and Python (the Eclipse plugins for those are very good now). Claus

  Read the article

• Why is it bad to map network drives in Windows?

  - by Beeblebrox

  There has been some spirited discussion within our IT department about mapping network drives. In particular, it has been said that mapping network drives is A Bad Thing and that adding DFS paths or network shares to your (Windows Explorer/Libraries) Favourites is a far better solution. Why is this the case? Personally I find the convenience of z:\folder to be better than \\server\path\folder', particularly with cmd line and scripting (of course I'm not talking about hard-coded links, naturally!). I have tried searching for pros and cons of mapped network drives, but I haven't seen anything other than 'should the network go down, the drive will be unavailable'. But this is a limitation of any network-accessed storage... I have also been told that mapped network drives poll the network when the network resource is unavailable, however I haven't found more information on this. Wouldn't this still be an issue with other network access mechanisms (that is, mapped Favourites) whenever Windows tries to enumerate the file system (for example, when a file/folder picker dialog is opened)? -- Do network drives poll the network any more than a Windows Explorer library/favourite?

  Read the article

• Why does my DSL modem now need a reboot each time for my laptop to connect?

  - by msorens

  I have a rather peculiar home networking issue. For sometime my home network was purring along fine. I could turn on either of my laptops and they would quickly find and connect to my DSL modem (and thence the internet). Several days ago I unplugged my DSL modem for the first time in months. Upon turning it back on and waiting for the boot to finish, the lights on the panel indicated the DSL modem was fully operational, just as before. But that's not what happened. Not at all. Now when I turn on my Win7 laptop, the network icon in my system tray shows a small starburst; hovering over it the tooltip states "Not connected; connections are available". Clicking it lists several nearby networks including my own network showing a strong signal. If I click to connect, it attempts a connection but then I get a dialog stating "Windows was unable to connect to MyNet.". Turning off wireless on my laptop and turning it back on yields no difference. Running the network troubleshooter (which includes doing a repair on the network connection) yields no difference. The only remedy is to reboot the DSL modem (i.e. unplug it, wait a few seconds, then plug it back in). As soon as it goes online my laptop finds it and connects properly. To add one more twist to the story, this happened to me once before, several months ago. After a couple weeks, the situation resolved itself(!). Everything started working properly again, due to nothing I did. Final note: this problem only affects the wireless connection to the DSL modem. My desktop computer, connected via hardline to the DSL modem, connects fine when I turn it on. Any thoughts on why this is happening or how to fix it?

  Read the article

• Forcing users to change password on first login - Windows Server 2008 R2 Remote Desktop Services

  - by George Durzi

  I'm setting up a demo lab environment in which each demo lab user is assigned 4 accounts to use in the lab. Users access the lab via Remote Desktop to the "client" machine in the lab - exposed at demolab.mydomain.com. The Client machine is a Windows 2008 Server R2 Enterprise Edition server The Remote Desktop Services role is configured on this server Remote Connection settings are configured to allow users to connect with any version of the Remote Desktop Client All accounts are members of the local Administrators and Remote Desktop Users groups All accounts are configured to be forced to change the default password after first login The user is instructed to remote into the lab with an account designated as their main account, and establish 3 more remote desktop sessions within the lab using their 3 other assigned demo lab accounts. When establishing the initial remote desktop connection to the lab using their main account, the user sees the change password dialog as expected. However, after logging in and trying to establish remote desktop connections to the server with their three other accounts, they are prompted that they need to change the password after logging in but can't continue with the login process - they don't see the expected change password experience. After logging in with a primary accounts, it doesn't make a difference if I try establishing a Remote Desktop connection to the environment using the name of the server, e.g. Client, or demolab.mydomain.com. I experimented with changing the settings for Remote Connections to require NLA but that didn't make a different. Appreciate any tips. Thanks

  Read the article

• Everyone can access my Windows 7 Homegroup file shares - Even Windows XP computers.

  - by adriangrigore

  Hi, I have 3 computers in my network, two running Windows 7 and one running Windows XP. I've set up a homegroup on both Windows 7 computers. Also, all computers are in the same Workgroup. The problem is that one of the Windows 7 computers makes all shares accessible to the entire Workgroup instead of just sharing to the Homegroup as it should be. I created the file share in Windows 7 via right-click in the explorer, then click on "Share For" - "Homegroup (Read/Write)" (translated from German, so the actual wording may be different). Also, when I look at the file sharing properties of that folder, Windows Explorer informs me that Users must have a valid account and password for this Computer to access drive shares. Unfortunately this is not true. Being in the same Workgroup is enough to get access. Homegroup restrictions work as expected on my other Windows 7 computer. When trying to browse those shares from the XP computer, I get a dialog asking for a login and password. What might cause homegroup restrictions to fail and how can I fix this?

  Read the article

• How to deploy website in IIS with a host name?

  - by Jayakumar

  I try to host my application in IIS. Below are the steps that I follow: Publish the code and place it in a path. Open IIS, right click on "sites" and select "Add Website". In that dialog I gave the site name and selected the app pool created for the application. I selected the physical path of the published code. I left the IP and port in the binding section without changes. and, finally, gave the host name as fus.km.com. When I try to browse the application the page is not Loading "Internet Explorer cannot display the Page" The machine domain is km.com UPDATE I tried to add the host name to the host file and flushed the DNS. The application asked for user credentials (I use windows Authentication in the application). But it did not login. On repeated tries it throws the error: HTTP Error 401.1 - Unauthorized You do not have permission to view this directory or page using the credentials that you supplied. I tried with different user to login but I get the same result.

  Read the article

• Home Sharing and Remote on iTunes causing firewall nags

  - by BoltClock

  It seems that enabling Home Sharing and/or hooking up my iPhone's Remote to iTunes causes Mac OS X Snow Leopard's firewall to freak out and keep nagging every time I launch iTunes to ask if I'd like it to accept incoming connections. If I turn off Home Sharing and forget all Remotes, the nag dialog no longer comes up. I could also disable the firewall, but I think that's a silly thing to do. iTunes is already in the firewall whitelist, so the only thing I know that could cause Mac OS X to nag is a bad application bundle code signature. I checked with this Terminal command: $ codesign -vvv /Applications/iTunes.app/ And sure enough, this is what it outputs: /Applications/iTunes.app/: a sealed resource is missing or invalid /Applications/iTunes.app/Contents/Resources/English.lproj/AutofillSettings.nib/objects.xib: resource added /Applications/iTunes.app/Contents/Resources/English.lproj/iTunesDJSettings.nib/objects.xib: resource added /Applications/iTunes.app/Contents/Resources/English.lproj/MobilePhonePrefs.nib/objects.xib: resource added /Applications/iTunes.app/Contents/Resources/English.lproj/MobilePhoneSetup.nib/objects.xib: resource added /Applications/iTunes.app/Contents/Resources/English.lproj/UniversalAccess.nib/objects.xib: resource added I've tried reinstalling iTunes as suggested by this answer, but Mac OS X still nags about incoming connections and the exact same output is generated when I run the above command again. On my PC, Windows Firewall has never nagged whenever I turn on Home Sharing and hook up Remote on my iPhone. Both computers use iTunes 9.2.1. My Mac runs Mac OS X 10.6.4. Is there anything special I need to do that I might have missed? Or how do I resolve the issue? EDIT: I've updated to iTunes 10, but the nags on my Mac are still there and only go away if I turn off Home Sharing and Remote. EDIT 2: I've updated to Remote 2.0 on my iPhone, but the firewall nags are persisting. Has anyone else had this firewall issue at all?

  Read the article

• How can I safely close this window and forever avoid seeing similar pop-ups from Mackeeper Zeobit's malware and spyware?

  - by Michael Prescott

  The attached image shows a window that just popped up and the only button available is the OK button. I could Force quit Safari, but I've got several sites open right now and don't want to try and find my place again. Besides, I've seen similar hacks in the past and I'd like to learn how to handle them in a way better than just a brute force-quit. I've never heard of MacKeeper or Zeobit, so I opened Firefox and did a few searches while Safari is obviously still stuck, waiting for me to click the sneaky OK button in the dialog window. Anyhow, at least the first few pages of most search results contain lots of blabbering from questionable witnesses about how MacKeeper saved them from some malware or spyware. However, any company that is hacking the browser to maliciously install their product is itself the criminal and not providing a true security application. So, there are three questions here: How can I close this window? Can I do something to Safari to avoid these hacks in the future? (Just curious) Is MacKeeper or Zeobit somehow loading the search results so that no information about their application being malware or spyware is listed (I can't be the only person in the world that is offended by their tactics, even though it appears I am)?

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >