Search Results

Search found 10087 results on 404 pages for 'dynamic arrays'.

Page 177/404 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• What does it mean when ARP shows <incomplete> on eth1

  - by Geoff Dalgas

  We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps.

  Read the article

• Cisco PIX firewall blocking inbound Exchange email

  - by sumsaricum

  [Cisco PIX, SBS2003] I can telnet server port 25 from inside but not outside, hence all inbound email is blocked. (as an aside, inbox on iPhones do not list/update emails, but calendar works a charm) I'm inexperienced in Cisco PIX and looking for some assistance before mails start bouncing :/ interface ethernet0 auto interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname pixfirewall domain-name ciscopix.com fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 no fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names name 192.168.1.10 SERVER access-list inside_outbound_nat0_acl permit ip 192.168.1.0 255.255.255.0 192.168.1.96 255.255.255.240 access-list outside_cryptomap_dyn_20 permit ip any 192.168.1.96 255.255.255.240 access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq 3389 access-list outside_acl permit tcp any interface outside eq ftp access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq https access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq www access-list outside_acl permit tcp any interface outside eq 993 access-list outside_acl permit tcp any interface outside eq imap4 access-list outside_acl permit tcp any interface outside eq 465 access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq smtp access-list outside_cryptomap_dyn_40 permit ip any 192.168.1.96 255.255.255.240 access-list COMPANYVPN_splitTunnelAcl permit ip 192.168.1.0 255.255.255.0 any access-list COMPANY_splitTunnelAcl permit ip 192.168.1.0 255.255.255.0 any access-list outside_cryptomap_dyn_60 permit ip any 192.168.1.96 255.255.255.240 access-list COMPANY_VPN_splitTunnelAcl permit ip 192.168.1.0 255.255.255.0 any access-list outside_cryptomap_dyn_80 permit ip any 192.168.1.96 255.255.255.240 pager lines 24 icmp permit host 217.157.xxx.xxx outside mtu outside 1500 mtu inside 1500 ip address outside 213.xxx.xxx.xxx 255.255.255.128 ip address inside 192.168.1.1 255.255.255.0 ip audit info action alarm ip audit attack action alarm ip local pool VPN 192.168.1.100-192.168.1.110 pdm location 0.0.0.0 255.255.255.128 outside pdm location 0.0.0.0 255.255.255.0 inside pdm location 217.yyy.yyy.yyy 255.255.255.255 outside pdm location SERVER 255.255.255.255 inside pdm logging informational 100 pdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_outbound_nat0_acl nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx 3389 SERVER 3389 netmask 255.255.255.255 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx smtp SERVER smtp netmask 255.255.255.255 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx https SERVER https netmask 255.255.255.255 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx www SERVER www netmask 255.255.255.255 0 0 static (inside,outside) tcp interface imap4 SERVER imap4 netmask 255.255.255.255 0 0 static (inside,outside) tcp interface 993 SERVER 993 netmask 255.255.255.255 0 0 static (inside,outside) tcp interface 465 SERVER 465 netmask 255.255.255.255 0 0 static (inside,outside) tcp interface ftp SERVER ftp netmask 255.255.255.255 0 0 access-group outside_acl in interface outside route outside 0.0.0.0 0.0.0.0 213.zzz.zzz.zzz timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout sip-disconnect 0:02:00 sip-invite 0:03:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ max-failed-attempts 3 aaa-server TACACS+ deadtime 10 aaa-server RADIUS protocol radius aaa-server RADIUS max-failed-attempts 3 aaa-server RADIUS deadtime 10 aaa-server RADIUS (inside) host SERVER *** timeout 10 aaa-server LOCAL protocol local http server enable http 217.yyy.yyy.yyy 255.255.255.255 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable sysopt connection permit-ipsec crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5 crypto dynamic-map outside_dyn_map 40 match address outside_cryptomap_dyn_40 crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-MD5 crypto dynamic-map outside_dyn_map 60 match address outside_cryptomap_dyn_60 crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-MD5 crypto dynamic-map outside_dyn_map 80 match address outside_cryptomap_dyn_80 crypto dynamic-map outside_dyn_map 80 set transform-set ESP-3DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map client authentication RADIUS LOCAL crypto map outside_map interface outside isakmp enable outside isakmp policy 20 authentication pre-share isakmp policy 20 encryption 3des isakmp policy 20 hash md5 isakmp policy 20 group 2 isakmp policy 20 lifetime 86400 telnet 217.yyy.yyy.yyy 255.255.255.255 outside telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 217.yyy.yyy.yyy 255.255.255.255 outside ssh 0.0.0.0 255.255.255.0 inside ssh timeout 5 management-access inside console timeout 0 dhcpd address 192.168.1.20-192.168.1.40 inside dhcpd dns SERVER 195.184.xxx.xxx dhcpd wins SERVER dhcpd lease 3600 dhcpd ping_timeout 750 dhcpd auto_config outside dhcpd enable inside : end I have Kiwi SysLog running but could use some pointers in that regard to narrow down the torrent of log messages, if that helps?!

  Read the article

• Is there any better way for creating a dynamic HTML table without using any javascript library like

  - by piemesons

  Dont worry we dont need to find out any bug in this code.. Its working perfectly.:-P My boss came to me and said "Hey just tell me whats the best of way of writing code for a dynamic HTML table (add row, delete row, update row).No need to add any CSS. Just javascript. No Jquery library etc. I was confused that in the middle of the project why he asking for some stupid exercise like this. What ever i wrote the following code and mailed him and after 15 mins i got a mail from him. " I was expecting much better code from a guy like you. Anyways good job monkey.(And with a picture of monkey as attachment.) thats was the mail. Line by line. I want to reply him but before that i want to know about the quality of my code. Is this really shitty...!!! Or he was just making fun of mine. I dont think that code is really shitty. Still correct me if you can.Code is working perfectly fine. Just copy paste it in a HTML file. <html> <head> <title> Exercise CSS </title> <script type="text/javascript"> function add_row() { var table = document.getElementById('table'); var rowCount = table.rows.length; var row = table.insertRow(rowCount); var cell1 = row.insertCell(0); var element1 = document.createElement("input"); element1.type = "text"; cell1.appendChild(element1); var cell2 = row.insertCell(1); var element2 = document.createElement("input"); element2.type = "text"; cell2.appendChild(element2); var cell3 = row.insertCell(2); cell3.innerHTML = ' <span onClick="edit(this)">Edit</span>/<span onClick="delete_row(this)">Delete</span>'; cell3.setAttribute("style", "display:none;"); var cell4 = row.insertCell(3); cell4.innerHTML = '<span onClick="save(this)">Save</span>'; } function save(e) { var elTableCells = e.parentNode.parentNode.getElementsByTagName("td"); elTableCells[0].innerHTML=elTableCells[0].firstChild.value; elTableCells[1].innerHTML=elTableCells[1].firstChild.value; elTableCells[2].setAttribute("style", "display:block;"); elTableCells[3].setAttribute("style", "display:none;"); } function edit(e) { var elTableCells = e.parentNode.parentNode.getElementsByTagName("td"); elTableCells[0].innerHTML='<input type="text" value="'+elTableCells[0].innerHTML+'">'; elTableCells[1].innerHTML='<input type="text" value="'+elTableCells[1].innerHTML+'">'; elTableCells[2].setAttribute("style", "display:none;"); elTableCells[3].setAttribute("style", "display:block;"); } function delete_row(e) { e.parentNode.parentNode.parentNode.removeChild(e.parentNode.parentNode); } </script> </head> <body > <div id="display"> <table id='table'> <tr id='id'> <td> Piemesons </td> <td> 23 </td> <td > <span onClick="edit(this)">Edit</span>/<span onClick="delete_row(this)">Delete</span> </td> <td style="display:none;"> <span onClick="save(this)">Save</span> </td> </tr> </table> <input type="button" value="Add new row" onClick="add_row();" /> </div> </body>

  Read the article

• how do I use html block snippets with dynamic content inside a django template that extends another

  - by stackoverflowusername

  Hi. Can someone please help me figure out a way to achieve the following (see snippets below) in Django templates? I know that you cannot use more than one extends, but I am new to django and I do not know the proper syntax for something like this. I want to be able to do this so that I can use my nested div layout for css reasons without having to type it like that each time and risking a typo. In words, I want to be able to have a page template extend my base.html file and then use html snippets of dynamic template content (i.e. template for loops or other template logic devices, not just a context variable I set from my view controller). ------------------------------------------------------------ base.html ------------------------------------------------------------ <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en"> <head> <meta http-equiv="Content-Type" content="text/html;charset=utf-8" /> <title>{% block title %}Title{% endblock %}</title> </head> <body> <div class="wrapper"> <div class="header"> This is the common header </div> <div class="nav"> This is the common nav </div> {% if messages %} <div class="messages"> <ul> {% for message in messages %} <li{% if message.tags %} class="{{ message.tags }}"{% endif %}>{{ message }}</li> {% endfor %} </ul> </div> {% endif %} <div class="content"> {% block content %}Page Content{% endblock %} </div> <div class="footer"> This is the common footer </div> </div> </body> </html> ------------------------------------------------------------ columnlayout2.html ------------------------------------------------------------ <div class="twocol container2"> <div class="container1"> <div class="col1"> {% block twocol_col1 %}{% endblock %} </div> <div class="col2"> {% block twocol_col2 %}{% endblock %} </div> </div> </div> ------------------------------------------------------------ columnlayout3.html ------------------------------------------------------------ <div class="threecol container3"> <div class="container2"> <div class="container1"> <div class="col1"> {% block threecol_col1 %}{% endblock %} </div> <div class="col2"> {% block threecol_col2 %}{% endblock %} </div> <div class="col3"> {% block threecol_col3 %}{% endblock %} </div> </div> </div> </div> ------------------------------------------------------------ page.html ------------------------------------------------------------ {% extends "base.html" %} {% block content %} {% extends "columnlayout2.html" %} {% block twocol_col1 %}twocolumn column 1{% endblock %} {% block twocol_col2 %}twocolumn column 2{% endblock %} {% extends "columnlayout3.html" %} {% block threecol_col1 %}threecol column 1{% endblock %} {% block threecol_col2 %}threecol column 2{% endblock %} {% block threecol_col3 %}threecol column 3{% endblock %} {% endblock %} ------------------------------------------------------------ page.html output ------------------------------------------------------------ <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en"> <head> <meta http-equiv="Content-Type" content="text/html;charset=utf-8" /> <title>Title</title> </head> <body> <div class="wrapper"> <div class="header"> This is the common header </div> <div class="nav"> This is the common nav </div> <div class="content"> <div class="twocol container2"> <div class="container1"> <div class="col1"> twocolumn column 1 </div> <div class="col2"> twocolumn column 2 </div> </div> </div> <div class="threecol container3"> <div class="container2"> <div class="container1"> <div class="col1"> threecol column 1 </div> <div class="col2"> threecol column 2 </div> <div class="col3"> threecol column 3 </div> </div> </div> </div> </div> <div class="footer"> This is the common footer </div> </div> </body> </html>

  Read the article

• Dynamically creating a Generic Type at Runtime

  - by Rick Strahl

  I learned something new today. Not uncommon, but it's a core .NET runtime feature I simply did not know although I know I've run into this issue a few times and worked around it in other ways. Today there was no working around it and a few folks on Twitter pointed me in the right direction. The question I ran into is: How do I create a type instance of a generic type when I have dynamically acquired the type at runtime? Yup it's not something that you do everyday, but when you're writing code that parses objects dynamically at runtime it comes up from time to time. In my case it's in the bowels of a custom JSON parser. After some thought triggered by a comment today I realized it would be fairly easy to implement two-way Dictionary parsing for most concrete dictionary types. I could use a custom Dictionary serialization format that serializes as an array of key/value objects. Basically I can use a custom type (that matches the JSON signature) to hold my parsed dictionary data and then add it to the actual dictionary when parsing is complete. Generic Types at Runtime One issue that came up in the process was how to figure out what type the Dictionary<K,V> generic parameters take. Reflection actually makes it fairly easy to figure out generic types at runtime with code like this: if (arrayType.GetInterface("IDictionary") != null) { if (arrayType.IsGenericType) { var keyType = arrayType.GetGenericArguments()[0]; var valueType = arrayType.GetGenericArguments()[1]; … } } The GetArrayType method gets passed a type instance that is the array or array-like object that is rendered in JSON as an array (which includes IList, IDictionary, IDataReader and a few others). In my case the type passed would be something like Dictionary<string, CustomerEntity>. So I know what the parent container class type is. Based on the the container type using it's then possible to use GetGenericTypeArguments() to retrieve all the generic types in sequential order of definition (ie. string, CustomerEntity). That's the easy part. Creating a Generic Type and Providing Generic Parameters at RunTime The next problem is how do I get a concrete type instance for the generic type? I know what the type name and I have a type instance is but it's generic, so how do I get a type reference to keyvaluepair<K,V> that is specific to the keyType and valueType above? Here are a couple of things that come to mind but that don't work (and yes I tried that unsuccessfully first): Type elementType = typeof(keyvalue<keyType, valueType>); Type elementType = typeof(keyvalue<typeof(keyType), typeof(valueType)>); The problem is that this explicit syntax expects a type literal not some dynamic runtime value, so both of the above won't even compile. I turns out the way to create a generic type at runtime is using a fancy bit of syntax that until today I was completely unaware of: Type elementType = typeof(keyvalue<,>).MakeGenericType(keyType, valueType); The key is the type(keyvalue<,>) bit which looks weird at best. It works however and produces a non-generic type reference. You can see the difference between the full generic type and the non-typed (?) generic type in the debugger: The nonGenericType doesn't show any type specialization, while the elementType type shows the string, CustomerEntity (truncated above) in the type name. Once the full type reference exists (elementType) it's then easy to create an instance. In my case the parser parses through the JSON and when it completes parsing the value/object it creates a new keyvalue<T,V> instance. Now that I know the element type that's pretty trivial with: // Objects start out null until we find the opening tag resultObject = Activator.CreateInstance(elementType); Here the result object is picked up by the JSON array parser which creates an instance of the child object (keyvalue<K,V>) and then parses and assigns values from the JSON document using the types  key/value property signature. Internally the parser then takes each individually parsed item and adds it to a list of  List<keyvalue<K,V>> items. Parsing through a Generic type when you only have Runtime Type Information When parsing of the JSON array is done, the List needs to be turned into a defacto Dictionary<K,V>. This should be easy since I know that I'm dealing with an IDictionary, and I know the generic types for the key and value. The problem is again though that this needs to happen at runtime which would mean using several Convert.ChangeType() calls in the code to dynamically cast at runtime. Yuk. In the end I decided the easier and probably only slightly slower way to do this is a to use the dynamic type to collect the items and assign them to avoid all the dynamic casting madness: else if (IsIDictionary) { IDictionary dict = Activator.CreateInstance(arrayType) as IDictionary; foreach (dynamic item in items) { dict.Add(item.key, item.value); } return dict; } This code creates an instance of the generic dictionary type first, then loops through all of my custom keyvalue<K,V> items and assigns them to the actual dictionary. By using Dynamic here I can side step all the explicit type conversions that would be required in the three highlighted areas (not to mention that this nested method doesn't have access to the dictionary item generic types here). Static <- -> Dynamic Dynamic casting in a static language like C# is a bitch to say the least. This is one of the few times when I've cursed static typing and the arcane syntax that's required to coax types into the right format. It works but it's pretty nasty code. If it weren't for dynamic that last bit of code would have been a pretty ugly as well with a bunch of Convert.ChangeType() calls to litter the code. Fortunately this type of type convulsion is rather rare and reserved for system level code. It's not every day that you create a string to object parser after all :-)© Rick Strahl, West Wind Technologies, 2005-2011Posted in .NET  CSharp   Tweet (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• SPARC T4-4 Beats 8-CPU IBM POWER7 on TPC-H @3000GB Benchmark

  - by Brian

  Oracle's SPARC T4-4 server delivered a world record TPC-H @3000GB benchmark result for systems with four processors. This result beats eight processor results from IBM (POWER7) and HP (x86). The SPARC T4-4 server also delivered better performance per core than these eight processor systems from IBM and HP. Comparisons below are based upon system to system comparisons, highlighting Oracle's complete software and hardware solution. This database world record result used Oracle's Sun Storage 2540-M2 arrays (rotating disk) connected to a SPARC T4-4 server running Oracle Solaris 11 and Oracle Database 11g Release 2 demonstrating the power of Oracle's integrated hardware and software solution. The SPARC T4-4 server based configuration achieved a TPC-H scale factor 3000 world record for four processor systems of 205,792 QphH@3000GB with price/performance of $4.10/QphH@3000GB. The SPARC T4-4 server with four SPARC T4 processors (total of 32 cores) is 7% faster than the IBM Power 780 server with eight POWER7 processors (total of 32 cores) on the TPC-H @3000GB benchmark. The SPARC T4-4 server is 36% better in price performance compared to the IBM Power 780 server on the TPC-H @3000GB Benchmark. The SPARC T4-4 server is 29% faster than the IBM Power 780 for data loading. The SPARC T4-4 server is up to 3.4 times faster than the IBM Power 780 server for the Refresh Function. The SPARC T4-4 server with four SPARC T4 processors is 27% faster than the HP ProLiant DL980 G7 server with eight x86 processors on the TPC-H @3000GB benchmark. The SPARC T4-4 server is 52% faster than the HP ProLiant DL980 G7 server for data loading. The SPARC T4-4 server is up to 3.2 times faster than the HP ProLiant DL980 G7 for the Refresh Function. The SPARC T4-4 server achieved a peak IO rate from the Oracle database of 17 GB/sec. This rate was independent of the storage used, as demonstrated by the TPC-H @3000TB benchmark which used twelve Sun Storage 2540-M2 arrays (rotating disk) and the TPC-H @1000TB benchmark which used four Sun Storage F5100 Flash Array devices (flash storage). [*] The SPARC T4-4 server showed linear scaling from TPC-H @1000GB to TPC-H @3000GB. This demonstrates that the SPARC T4-4 server can handle the increasingly larger databases required of DSS systems. [*] The SPARC T4-4 server benchmark results demonstrate a complete solution of building Decision Support Systems including data loading, business questions and refreshing data. Each phase usually has a time constraint and the SPARC T4-4 server shows superior performance during each phase. [*] The TPC believes that comparisons of results published with different scale factors are misleading and discourages such comparisons. Performance Landscape The table lists the leading TPC-H @3000GB results for non-clustered systems. TPC-H @3000GB, Non-Clustered Systems System Processor P/C/T – Memory Composite(QphH) $/perf($/QphH) Power(QppH) Throughput(QthH) Database Available SPARC Enterprise M9000 3.0 GHz SPARC64 VII+ 64/256/256 – 1024 GB 386,478.3 $18.19 316,835.8 471,428.6 Oracle 11g R2 09/22/11 SPARC T4-4 3.0 GHz SPARC T4 4/32/256 – 1024 GB 205,792.0 $4.10 190,325.1 222,515.9 Oracle 11g R2 05/31/12 SPARC Enterprise M9000 2.88 GHz SPARC64 VII 32/128/256 – 512 GB 198,907.5 $15.27 182,350.7 216,967.7 Oracle 11g R2 12/09/10 IBM Power 780 4.1 GHz POWER7 8/32/128 – 1024 GB 192,001.1 $6.37 210,368.4 175,237.4 Sybase 15.4 11/30/11 HP ProLiant DL980 G7 2.27 GHz Intel Xeon X7560 8/64/128 – 512 GB 162,601.7 $2.68 185,297.7 142,685.6 SQL Server 2008 10/13/10 P/C/T = Processors, Cores, Threads QphH = the Composite Metric (bigger is better) $/QphH = the Price/Performance metric in USD (smaller is better) QppH = the Power Numerical Quantity QthH = the Throughput Numerical Quantity The following table lists data load times and refresh function times during the power run. TPC-H @3000GB, Non-Clustered Systems Database Load & Database Refresh System Processor Data Loading(h:m:s) T4Advan RF1(sec) T4Advan RF2(sec) T4Advan SPARC T4-4 3.0 GHz SPARC T4 04:08:29 1.0x 67.1 1.0x 39.5 1.0x IBM Power 780 4.1 GHz POWER7 05:51:50 1.5x 147.3 2.2x 133.2 3.4x HP ProLiant DL980 G7 2.27 GHz Intel Xeon X7560 08:35:17 2.1x 173.0 2.6x 126.3 3.2x Data Loading = database load time RF1 = power test first refresh transaction RF2 = power test second refresh transaction T4 Advan = the ratio of time to T4 time Complete benchmark results found at the TPC benchmark website http://www.tpc.org. Configuration Summary and Results Hardware Configuration: SPARC T4-4 server 4 x SPARC T4 3.0 GHz processors (total of 32 cores, 128 threads) 1024 GB memory 8 x internal SAS (8 x 300 GB) disk drives External Storage: 12 x Sun Storage 2540-M2 array storage, each with 12 x 15K RPM 300 GB drives, 2 controllers, 2 GB cache Software Configuration: Oracle Solaris 11 11/11 Oracle Database 11g Release 2 Enterprise Edition Audited Results: Database Size: 3000 GB (Scale Factor 3000) TPC-H Composite: 205,792.0 QphH@3000GB Price/performance: $4.10/QphH@3000GB Available: 05/31/2012 Total 3 year Cost: $843,656 TPC-H Power: 190,325.1 TPC-H Throughput: 222,515.9 Database Load Time: 4:08:29 Benchmark Description The TPC-H benchmark is a performance benchmark established by the Transaction Processing Council (TPC) to demonstrate Data Warehousing/Decision Support Systems (DSS). TPC-H measurements are produced for customers to evaluate the performance of various DSS systems. These queries and updates are executed against a standard database under controlled conditions. Performance projections and comparisons between different TPC-H Database sizes (100GB, 300GB, 1000GB, 3000GB, 10000GB, 30000GB and 100000GB) are not allowed by the TPC. TPC-H is a data warehousing-oriented, non-industry-specific benchmark that consists of a large number of complex queries typical of decision support applications. It also includes some insert and delete activity that is intended to simulate loading and purging data from a warehouse. TPC-H measures the combined performance of a particular database manager on a specific computer system. The main performance metric reported by TPC-H is called the TPC-H Composite Query-per-Hour Performance Metric (QphH@SF, where SF is the number of GB of raw data, referred to as the scale factor). QphH@SF is intended to summarize the ability of the system to process queries in both single and multiple user modes. The benchmark requires reporting of price/performance, which is the ratio of the total HW/SW cost plus 3 years maintenance to the QphH. A secondary metric is the storage efficiency, which is the ratio of total configured disk space in GB to the scale factor. Key Points and Best Practices Twelve Sun Storage 2540-M2 arrays were used for the benchmark. Each Sun Storage 2540-M2 array contains 12 15K RPM drives and is connected to a single dual port 8Gb FC HBA using 2 ports. Each Sun Storage 2540-M2 array showed 1.5 GB/sec for sequential read operations and showed linear scaling, achieving 18 GB/sec with twelve Sun Storage 2540-M2 arrays. These were stand alone IO tests. The peak IO rate measured from the Oracle database was 17 GB/sec. Oracle Solaris 11 11/11 required very little system tuning. Some vendors try to make the point that storage ratios are of customer concern. However, storage ratio size has more to do with disk layout and the increasing capacities of disks – so this is not an important metric in which to compare systems. The SPARC T4-4 server and Oracle Solaris efficiently managed the system load of over one thousand Oracle Database parallel processes. Six Sun Storage 2540-M2 arrays were mirrored to another six Sun Storage 2540-M2 arrays on which all of the Oracle database files were placed. IO performance was high and balanced across all the arrays. The TPC-H Refresh Function (RF) simulates periodical refresh portion of Data Warehouse by adding new sales and deleting old sales data. Parallel DML (parallel insert and delete in this case) and database log performance are a key for this function and the SPARC T4-4 server outperformed both the IBM POWER7 server and HP ProLiant DL980 G7 server. (See the RF columns above.) See Also Transaction Processing Performance Council (TPC) Home Page Ideas International Benchmark Page SPARC T4-4 Server oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 Enterprise Edition oracle.com OTN Sun Storage 2540-M2 Array oracle.com OTN Disclosure Statement TPC-H, QphH, $/QphH are trademarks of Transaction Processing Performance Council (TPC). For more information, see www.tpc.org. SPARC T4-4 205,792.0 QphH@3000GB, $4.10/QphH@3000GB, available 5/31/12, 4 processors, 32 cores, 256 threads; IBM Power 780 QphH@3000GB, 192,001.1 QphH@3000GB, $6.37/QphH@3000GB, available 11/30/11, 8 processors, 32 cores, 128 threads; HP ProLiant DL980 G7 162,601.7 QphH@3000GB, $2.68/QphH@3000GB available 10/13/10, 8 processors, 64 cores, 128 threads.

  Read the article

• Run time insert using bulk update ,giving an internal error?

  - by Vineet

  Hi , I am trying to make a run time table named dynamic and inserting data into it from index by table using bulk update,but when i am trying to execute it this error is coming: ERROR at line 1: ORA-06550: line 0, column 0: PLS-00801: internal error [74301 ] declare type index_tbl_type IS table of number index by binary_integer; num_tbl index_tbl_type; TYPE ref_cur IS REF CURSOR; cur_emp ref_cur; begin execute immediate 'create table dynamic (v_num number)';--Creating a run time tabl FOR i in 1..10000 LOOP execute immediate 'insert into dynamic values('||i||')';--run time insert END LOOP; OPEN cur_emp FOR 'select * from dynamic';--opening ref cursor FETCH cur_emp bulk collect into num_tbl;--bulk inserting in index by table close cur_emp; FORALL i in num_tbl.FIRST..num_tbl.LAST --Bulk update execute immediate 'insert into dynamic values('||num_tbl(i)||')'; end;

  Read the article

• Why learn Perl, Python, Ruby if the company is using C++, C# or Java as the application language?

  - by szabgab

  I wonder why would a C++, C#, Java developer want to learn a dynamic language? Assuming the company won't switch its main development language from C++/C#/Java to a dynamic one what use is there for a dynamic language? What helper tasks can be done by the dynamic languages faster or better after only a few days of learning than with the static language that you have been using for several years? Update After seeing the first few responses it is clear that there two issues. My main interest would be something that is justifiable to the employer as an expense. That is, I am looking for justifications for the employer to finance the learning of a dynamic language. Aside from the obvious that the employee will have broader view, the employers are usually looking for some "real" benefit.

  Read the article

• Subterranean IL: Generics and array covariance

  - by Simon Cooper

  Arrays in .NET are curious beasts. They are the only built-in collection types in the CLR, and SZ-arrays (single dimension, zero-indexed) have their own commands and IL syntax. One of their stranger properties is they have a kind of built-in covariance long before generic variance was added in .NET 4. However, this causes a subtle but important problem with generics. First of all, we need to briefly recap on array covariance. SZ-array covariance To demonstrate, I'll tweak the classes I introduced in my previous posts: public class IncrementableClass { public int Value; public virtual void Increment(int incrementBy) { Value += incrementBy; } } public class IncrementableClassx2 : IncrementableClass { public override void Increment(int incrementBy) { base.Increment(incrementBy); base.Increment(incrementBy); } } In the CLR, SZ-arrays of reference types are implicitly convertible to arrays of the element's supertypes, all the way up to object (note that this does not apply to value types). That is, an instance of IncrementableClassx2[] can be used wherever a IncrementableClass[] or object[] is required. When an SZ-array could be used in this fashion, a run-time type check is performed when you try to insert an object into the array to make sure you're not trying to insert an instance of IncrementableClass into an IncrementableClassx2[]. This check means that the following code will compile fine but will fail at run-time: IncrementableClass[] array = new IncrementableClassx2[1]; array[0] = new IncrementableClass(); // throws ArrayTypeMismatchException These checks are enforced by the various stelem* and ldelem* il instructions in such a way as to ensure you can't insert a IncrementableClass into a IncrementableClassx2[]. For the rest of this post, however, I'm going to concentrate on the ldelema instruction. ldelema This instruction pops the array index (int32) and array reference (O) off the stack, and pushes a pointer (&) to the corresponding array element. However, unlike the ldelem instruction, the instruction's type argument must match the run-time array type exactly. This is because, once you've got a managed pointer, you can use that pointer to both load and store values in that array element using the ldind* and stind* (load/store indirect) instructions. As the same pointer can be used for both input and output to the array, the type argument to ldelema must be invariant. At the time, this was a perfectly reasonable restriction, and maintained array type-safety within managed code. However, along came generics, and with it the constrained callvirt instruction. So, what happens when we combine array covariance and constrained callvirt? .method public static void CallIncrementArrayValue() { // IncrementableClassx2[] arr = new IncrementableClassx2[1] ldc.i4.1 newarr IncrementableClassx2 // arr[0] = new IncrementableClassx2(); dup newobj instance void IncrementableClassx2::.ctor() ldc.i4.0 stelem.ref // IncrementArrayValue<IncrementableClass>(arr, 0) // here, we're treating an IncrementableClassx2[] as IncrementableClass[] dup ldc.i4.0 call void IncrementArrayValue<class IncrementableClass>(!!0[],int32) // ... ret } .method public static void IncrementArrayValue<(IncrementableClass) T>( !!T[] arr, int32 index) { // arr[index].Increment(1) ldarg.0 ldarg.1 ldelema !!T ldc.i4.1 constrained. !!T callvirt instance void IIncrementable::Increment(int32) ret } And the result: Unhandled Exception: System.ArrayTypeMismatchException: Attempted to access an element as a type incompatible with the array. at IncrementArrayValue[T](T[] arr, Int32 index) at CallIncrementArrayValue() Hmm. We're instantiating the generic method as IncrementArrayValue<IncrementableClass>, but passing in an IncrementableClassx2[], hence the ldelema instruction is failing as it's expecting an IncrementableClass[]. On features and feature conflicts What we've got here is a conflict between existing behaviour (ldelema ensuring type safety on covariant arrays) and new behaviour (managed pointers to object references used for every constrained callvirt on generic type instances). And, although this is an edge case, there is no general workaround. The generic method could be hidden behind several layers of assemblies, wrappers and interfaces that make it a requirement to use array covariance when calling the generic method. Furthermore, this will only fail at runtime, whereas compile-time safety is what generics were designed for! The solution is the readonly. prefix instruction. This modifies the ldelema instruction to ignore the exact type check for arrays of reference types, and so it lets us take the address of array elements using a covariant type to the actual run-time type of the array: .method public static void IncrementArrayValue<(IncrementableClass) T>( !!T[] arr, int32 index) { // arr[index].Increment(1) ldarg.0 ldarg.1 readonly. ldelema !!T ldc.i4.1 constrained. !!T callvirt instance void IIncrementable::Increment(int32) ret } But what about type safety? In return for ignoring the type check, the resulting controlled mutability pointer can only be used in the following situations: As the object parameter to ldfld, ldflda, stfld, call and constrained callvirt instructions As the pointer parameter to ldobj or ldind* As the source parameter to cpobj In other words, the only operations allowed are those that read from the pointer; stind* and similar that alter the pointer itself are banned. This ensures that the array element we're pointing to won't be changed to anything untoward, and so type safety within the array is maintained. This is a typical example of the maxim that whenever you add a feature to a program, you have to consider how that feature interacts with every single one of the existing features. Although an edge case, the readonly. prefix instruction ensures that generics and array covariance work together and that compile-time type safety is maintained. Tune in next time for a look at the .ctor generic type constraint, and what it means.

  Read the article

• When to use an Array vs When to use a Vector, when dealing with GameObjects?

  - by user32465

  I understand that from other answers, Arrays and Vectors are the best choices. Many on SE claim that Linked Lists and Maps are bad for video game programming. I understand that for the most part, I can use Arrays. However, I don't really understand exactly when to use Vectors over Arrays. Why even use Vectors? Wouldn't it be best if I simply always used an Array, that way I know how much memory my game needs? Specifically my game would only ever load a single "Map" area of tiles, such as Map[100][100], so I could very easily have an array of GameObjectContainer GameObjects[100][100], which would reserve an entire map's worth of possible gameobjects, correct? So why use a Vector instead? Memory is quite large on modern hardware.

  Read the article

• Looking for feedback on design pattern for simple 2D environment

  - by Le Mot Juiced

  I'm working in iOS. I am trying to make a very simple 2D environment where there are some basic shapes you can drag around with your finger. These shapes should interact in various ways when dropped on each other, or when single-tapped versus double-tapped, etc. I don't know the name for the design pattern I'm thinking of. Basically, you have a bunch of arrays named after attributes, such as "double-tappable" or "draggable" or "stackable". You assign these attributes to the shapes by putting the shapes in the arrays. So, if there's a double-tap event, the code gets the location of it, then iterates through the "double-tappable" array to see if any of its members are in that location. And so on: every interactive event causes a scan through the appropriate array or arrays. It seems like that should work, but I'm wondering if there's a better pattern for the purpose.

  Read the article

• PHP extensions won't load on Apache startup

  - by WebDevHobo

  I've added php as a module for Apache 2.2.11: LoadModule php5_module "c:/php/php5apache2_2.dll" And also added AddType application/x-httpd-php .php And in PHP.ini, my extension dir is set to: extension_dir = "C:\php\ext" And yes, the directories are correct and all files do exist. But when I start apache, I get these errors: PHP Warning: PHP Startup: Unable to load dynamic library 'C:\php\ext\php_mysql.dll' - The specified module could not be found.\r\n in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library 'C:\php\ext\php_pdo_pgsql.dll' - The specified module could not be found.\r\n in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library 'C:\php\ext\php_pgsql.dll' - The specified module could not be found.\r\n in Unknown on line 0 [Sun May 17 03:46:01 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Sun May 17 03:46:01 2009] [notice] Server built: Dec 10 2008 00:10:06 [Sun May 17 03:46:01 2009] [notice] Parent: Created child process 4652 PHP Warning: PHP Startup: Unable to load dynamic library 'C:\php\ext\php_mysql.dll' - The specified module could not be found.\r\n in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library 'C:\php\ext\php_pdo_pgsql.dll' - The specified module could not be found.\r\n in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library 'C:\php\ext\php_pgsql.dll' - The specified module could not be found.\r\n in Unknown on line 0 [Sun May 17 03:46:01 2009] [notice] Child 4652: Child process is running [Sun May 17 03:46:01 2009] [notice] Child 4652: Acquired the start mutex. [Sun May 17 03:46:01 2009] [notice] Child 4652: Starting 64 worker threads. [Sun May 17 03:46:01 2009] [notice] Child 4652: Starting thread to listen on port 80. So I'm probably forgetting something simple here, can someone tell me what I'm forgetting?

  Read the article

• Grouping Categorized Data In WPF.

  - by VoidDweller

  Here is what I am trying to do. Dynamic Category: Columns can be 0 or more. Must contain 1 or more Type Columns. Will only be displayed if any row contains Type Column data associated with it. Data Rows: Will be added Asynchronously. Will be grouped by a Common Category column. Will add a Dynamic Category if it does not yet exist. Will add a Type Column if it does not yet exist within its appropriate Dynamic Category. Platform Info: WPF .Net 3.5 sp1 C# MVVM I have a few partially functional prototypes, but each has it's own major set of problems. Can any of you give me some guidance on this? Envision this nicely styled. :-) -------------------------------------------------------------------------- |[ Common Category ]|[ Dynamic Category 0 ]|[ Dynamic Category N ]| -------------------------------------------------------------------------- |[Header 1]|[Header 2]|[ Type 0 ]|[ Type N ]|[ Type 0 ]|[ Type N ]| -------------------------------------------------------------------------- |[Data 2 Group] | -------------------------------------------------------------------------- | Data A | Data 2 || Null | Data 1 || Data 0 | Data 1 || | Data B | Data 2 || Data 0 | Null || Data 0 | Data 1 || -------------------------------------------------------------------------- |[Data 1 Group] | -------------------------------------------------------------------------- | Data C | Data 1 || Null | Data 1 || Data 0 | Data 1 || | Data D | Data 1 || Null | Null || Data 0 | Null || -------------------------------------------------------------------------- Edit: Sorting and Paging is not necessary. I have looked at nested ListViews and DataGrids, dynamically building a Grid. Dynamically building a Grid and leveraging the SharedSizeGroup property seems the most promising strategy, but I am concerned about performance. Would a better approach be to consider this a dynamic report? If so, what should I be looking at? Thanks for your help.

  Read the article

• WPF dynamic layout: how to enforce square proportions (width equals height)?

  - by Gart

  I'm learning WPF and can't figure out how to enfore my buttons to take a square shape. Here is my XAML Markup: <Window x:Class="Example" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Height="368" Width="333"> <Window.Resources> <Style x:Key="ToggleStyle" BasedOn="{StaticResource {x:Type ToggleButton}}" TargetType="{x:Type RadioButton}"> </Style> </Window.Resources> <RadioButton Style="{StaticResource ToggleStyle}"> Very very long text </RadioButton> </Window> Specifying explicit values for Width and Height attributes seems like a wrong idea - the button should calculate its dimensions based on its contents automagically, but keep its width and height equal. Is this possible?

  Read the article

• Tracking changes in Entity Framework 4.0 using POCO Dynamic Proxies across multiple data contexts.

  - by Rob Packwood

  I started messing with EF 4.0 because I am curious about the POCO possibilities... I wanted to simulate disconnected web environment and wrote the following code to simulate this: Save a test object in the database. Retrieve the test object Dispose of the DataContext associated with the test object I used to retrieve it Update the test object Create a new data context and persist the changes on the test object that are automatically tracked within the DynamicProxy generated against my POCO object. The problem is that when I call dataContext.SaveChanges in the Test method above, the updates are not applied. The testStore entity shows a status of "Modified" when I check its EntityStateTracker, but it is no longer modified when I view it within the new dataContext's Stores property. I would have thought that calling the Attach method on the new dataContext would also bring the object's "Modified" state over, but that appears to not be the case. Is there something I am missing? I am definitely working with self-tracking POCOs using DynamicProxies. private static void SaveTestStore(string storeName = "TestStore") { using (var context = new DataContext()) { Store newStore = context.Stores.CreateObject(); newStore.Name = storeName; context.Stores.AddObject(newStore); context.SaveChanges(); } } private static Store GetStore(string storeName = "TestStore") { using (var context = new DataContext()) { return (from store in context.Stores where store.Name == storeName select store).SingleOrDefault(); } } [Test] public void Test_Store_Update_Using_Different_DataContext() { SaveTestStore(); Store testStore = GetStore(); testStore.Name = "Updated"; using (var dataContext = new DataContext()) { dataContext.Stores.Attach(testStore); dataContext.SaveChanges(SaveOptions.DetectChangesBeforeSave); } Store updatedStore = GetStore("Updated"); Assert.IsNotNull(updatedStore); }

  Read the article

• How to add dynamic profile fields in Invision Power Board?

  - by user361908

  I run a game server and want to link the persons in game character name and stats to Invision Power Board. I've setup IPB so players currently login with their in game login. That means their username on the forum is the same as their username for the game. They can have multiple characters on 1 account so ideally I'd like to allow them to choose a main character and display an actual image of that character and allow them to display other characters if they are online. Currently I'm doing something like this by hacking profileFields.php but it's messy and not very efficient on the user or server end. My code currently uses 2 custom fields which the player can enter their character names in. To display only their main character they enter the name in the first field. To also display other characters if they are online they enter the same name into the second field. To resolve the IDs I have to run a lot of queries. I know PHP but I am not familiar with IPBs code at all. I just need pointed in a direction where I can combine the 2 fields into 1 field. tl;dr: Here is my setup: Invision Power Board 3 Data is stored in MySQL on the same server the forum is hosted on. Usernames on the forum are identical to usernames in the game Here is a breakdown of what I'd like to do: In the edit profile section I need to resolve the forum username to the games account id then: Display a list of characters and allow them to choose which characters they want to display if they are online as well as a default character that will be displayed if none are online. In the posts user info pane: Display the online character or the default if none are online. Here is what I need to know: How to generate a list of characters in the profile edit form and allow selection (checkbox) of each character to display as well as the selection of a default character (radio or dropdown?) How to fetch the data and place it in the posts user info pane

  Read the article

• SGE: invoking qmake raises "critical error: can't resolve group"

  - by Pierre

  I'm new to SGE an I'm trying to run qmake with the simple following Makefile with our very new cluster: merge.txt: job1.txt job2.txt job3.txt ... cat $^ > $@ job1.txt: sleep 1 echo "Hello From " $@ > $@ sleep 1 job2.txt: sleep 2 echo "Hello From " $@ > $@ sleep 2 job3.txt: (...) the following command raises an error: qmake -l arch=lx24-amd64 -cwd -v PATH -- -j 4 sleep 1 dynamic mode sleep 2 dynamic mode sleep 3 dynamic mode sleep 4 dynamic mode critical error: can't resolve group qmake: *** [job3.txt] Error 1 critical error: can't resolve group qmake: *** [job2.txt] Error 1 critical error: can't resolve group qmake: *** [job1.txt] Error 1 critical error: can't resolve group what's wrong ?

  Read the article

• Dynamic changes to thread stack size in Solaris 9 ?

  - by Satya

  Hello, I am looking for a configurable / tunable on Solaris 9 through which I can change the default thread stack size without recompiling the code to use "pthread_attr_setstacksize" For example on HPUX 11.11 / 11.23 the environment variable "PTHREAD_DEFAULT_STACK_SIZE" can be exported (available via HPUX patches PHCO_38307 / PHCO_38955 ) - Is there a equivalent Solaris 9 way to achieve the same ? Thanks! Satya

  Read the article

• How to specify dynamic field names in a Linq where clause?

  - by Dr. Zim

  If you create a Filter object that contains criteria for Linq that normally goes in a where clause like this: var myFilterObject = FilterFactory.GetBlank(); myFilterObject.AddCondition("Salary", "lessThan", "40000"); var myResult = myRepository.GetEmployees(myFilterObject); How would you match the Linq field to the Field Name without using a big case statement? return from e in db.Employee where e.Salary < 40000 select new IList<EmployeeViewModel> { Name= e.name, Salary= e.Salary }; I assume you need to send an object to the Repository that specifies filtering so that you only pull what records you need. I assume Linq doesn't pre-compile (unless you create a customized delegate and function), so you should be able to dynamically specify which fields you want to filter. It would be nice if you could do something like e["Salary"] like some type of Expando Object.

  Read the article

• Dynamic State Machine in Ruby? Do State Machines Have to be Classes?

  - by viatropos

  Question is, are state machines always defined statically (on classes)? Or is there a way for me to have it so each instance of the class with has it's own set of states? I'm checking out Stonepath for implementing a Task Engine. I don't really see the distinction between "states" and "tasks" in there, so I'm thinking I could just map a Task directly to a state. This would allow me to be able to define task-lists (or workflows) dynamically, without having to do things like: aasm_event :evaluate do transitions :to => :in_evaluation, :from => :pending end aasm_event :accept do transitions :to => :accepted, :from => :pending end aasm_event :reject do transitions :to => :rejected, :from => :pending end Instead, a WorkItem (the main workflow/task manager model), would just have many tasks. Then the tasks would work like states, so I could do something like this: aasm_initial_state :initial tasks.each do |task| aasm_state task.name.to_sym end previous_state = nil tasks.each do |tasks| aasm_event task.name.to_sym do transitions :to => "#{task.name}_phase".to_sym, :from => previous_state ? "#{task.name}_phase" : "initial" end previous_state = state end However, I can't do that with the aasm gem because those methods (aasm_state and aasm_event) are class methods, so every instance of the class with that state machine has the same states. I want it so a "WorkItem" or "TaskList" dynmically creates a sequence of states and transitions based on the tasks it has. This would allow me to dynamically define workflows and just have states map to tasks. Are state machines ever used like this?

  Read the article

• OpenDNS IP Conflict

  - by Paddy

  I have downloaded the OpenDNS client and it was working great till today. Shows me this error: dynamic IP update failed with message !yours or "Your IP address is taken by another user." I am pretty sure i'll get away with the problem by just restarting my connection as i'll be assigned a new dynamic ip. But I wonder how this is happening in the first place. Shouldn't Dynamic IP be unique for everyone?

  Read the article

• Issues with partitions WIN 7

  - by pomber

  I was trying to make some space to install linux in my HP notebook. The computer had 4 partitions, I made space shrinking one and created a new one (facepalm) using the windows partitioning tool. It show me some warning message saying something about dynamic partitions, I ingored it, and went to the linux live CD. I installed linux in the new partition, after the installation completed it told me that GRUB cannot be installed I dont remember why. So now, it doesnt boot, neither windows nor linux. After google for a while I found the diskpart command, it gives me this info: DISKPART> list disk DISK ### Status -------- --------------- DISK 0 Invalid DISKPART> select disk 0 DISKPART> select partition Partition ### TYPE ------------- -------------- Partition 1 Dynamic Data Partition 2 Dynamic Data Partition 3 Dynamic Data Partition 4 Primary <- I think I put linux here Any idea whats happening? Or how to solve it? Thanks

  Read the article

• How to bind dynamic NSNumber Object to SQLite query?

  - by Thomas Joos

  hi guys, I'm wondering how to bind an NSNumber object into a sqlite3 query: const char *sql = "select name from myTable where section_id=1 order by name ASC"; I have a NSNumber object called 'nmbr' and want to assign its value to the section id.. Thomas

  Read the article

• How to stretch textfield in a JasperReport as per dynamic content?

  - by Debadatta Viva la Vida

  http://jasperreports.sourceforge.net/xsd/jasperreport.xsd" name="tree-template" pageWidth="595" pageHeight="842" columnWidth="481" leftMargin="57" rightMargin="57" topMargin="72" bottomMargin="72" want this field to auto stretch as per content <textField isStretchWithOverflow="true" isBlankWhenNull="true"> <reportElement positionType="Float" stretchType="RelativeToTallestObject" x="0" y="80" width="463" height="20"/> <textElement> <font size="10"/> </textElement> <textFieldExpression class="java.lang.String"><![CDATA[$F{goals}==null ? "Not Defined":$F{goals}]]></textFieldExpression> </textField> want this field to auto stretch as per content <staticText> <reportElement stretchType="RelativeToTallestObject" x="0" y="100" width="98" height="20"/> <textElement> <font isBold="true"/> </textElement> <text><![CDATA[Status Details]]></text> </staticText> <textField isStretchWithOverflow="true"> <reportElement stretchType="RelativeToTallestObject" x="2" y="120" width="463" height="20"/> <textElement/> <textFieldExpression class="java.lang.String"><![CDATA[$F{statusDetails}==null ? "Not Defined":$F{statusDetails}]]></textFieldExpression> </textField> <staticText> <reportElement stretchType="RelativeToTallestObject" x="0" y="140" width="98" height="20"/> <textElement> <font isBold="true"/> </textElement> <text><![CDATA[Risk Mitigation]]></text> </staticText> <textField> <reportElement stretchType="RelativeToTallestObject" x="18" y="160" width="463" height="20"/> <textElement/> <textFieldExpression class="java.lang.String"><![CDATA[$F{mitigation}==null?"Not Defined":$F{mitigation}]]></textFieldExpression> </textField> <textField> <reportElement stretchType="RelativeToTallestObject" x="79" y="40" width="100" height="20"/> <textElement/> <textFieldExpression class="java.lang.String"><![CDATA[new SimpleDateFormat("MMM dd,yyyy").format($F{releaseDate}.getTime())]]></textFieldExpression> </textField> <line> <reportElement x="0" y="180" width="481" height="1"/> </line> </band> </detail> <columnFooter> <band height="12" splitType="Stretch"/> </columnFooter> <pageFooter> <band height="13" splitType="Stretch"> <frame> <reportElement mode="Opaque" x="0" y="0" width="477" height="13" forecolor="#D0B48E" backcolor="#9DB1B8"/> <textField pattern="EEEEE dd MMMMM yyyy"> <reportElement style="Column header" x="2" y="0" width="197" height="13" forecolor="#FFFFFF"/> <textElement verticalAlignment="Middle"> <font size="10" isBold="false"/> </textElement> <textFieldExpression class="java.util.Date"><![CDATA[new java.util.Date()]]></textFieldExpression> </textField> <textField evaluationTime="Report"> <reportElement style="Column header" x="450" y="0" width="27" height="13" forecolor="#FFFFFF"/> <textElement verticalAlignment="Middle"> <font size="10" isBold="false"/> </textElement> <textFieldExpression class="java.lang.String"><![CDATA[" " + $V{PAGE_NUMBER}]]></textFieldExpression> </textField> <textField> <reportElement style="Column header" x="370" y="0" width="80" height="13" forecolor="#FFFFFF"/> <textElement textAlignment="Right" verticalAlignment="Middle"> <font size="10" isBold="false"/> </textElement> <textFieldExpression class="java.lang.String"><![CDATA["Page "+$V{PAGE_NUMBER}+" of"]]></textFieldExpression> </textField> </frame> </band> </pageFooter> <summary> <band splitType="Stretch"/> </summary>

  Read the article

• asp.net dynamic sitemap with querystring? Session variable seems like overkill.

  - by Mike

  Hi, I'm using ASP.NET WebForms. I'm using the standard sitemap provider. Home User Account Entry Going to the home page should have a user selection screen. Clicking on a user should list out the user's accounts with options to edit, delete, add accounts. Selecting an account should list out all the user's account's entries with options to edit delete and add entries. How do you normally pass this information between pages? I could use the query string, but then, the sitemap doesn't work. The sitemap only has the exact page without the query string and therefore loses the information. /User/Account/List.aspx?User=123 /User/Account/Entry/List.aspx?User=123&Account=322 I could use a session variable, but this seems overkill. Thoughts and suggestions very appreciated. Thanks!

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >