Search Results

Search found 5055 results on 203 pages for 'pdf converter'.

Page 178/203 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• How do I use a Minitel terminal as a linux dumb terminal

  - by Pawz

  I recently purchased a US version of the Alcatel Minitel terminal. I think it's a 1B version. Pictures of it here: I tried connecting a null modem to the 25 pin port on the back and plugging it into a linux box running agetty but I couldn't get it to show any signs of being connected. I used Google Translate to translate this document into English: http://mirabellug.org/wikini/upload/Documentations_minitel.pdf As far as I can tell, you take it out of videotex mode by typing Fcnt-T A, then turn off local echo with Fcnt-T E, then set it to 4800 baud with Fcnt-P 4. I presume Fcnt refers to the "CTRL" key on my terminal. But I think I'm doing something wrong, because it doesn't look like it's recognising the keystrokes, because "Fcnt-T A" just prints the letter A to the screen, which is not what you'd expect a function key combo to do. Has anyone used these minitel terminals as a linux terminal, and if so, please can you share how to configure the minitel to run as a terminal ? Is the 25 pin plug even the correct port to use ? I read something online that indicated you're supposed to use the 5 pin DIN plug instead, is that right ? If so, what's the 25 pin plug for ? If I am supposed to use the DIN plug, does anyone know the pinouts so I can make a cable ?

  Read the article

• Debian DNSSEC - howto secure a domain?

  - by Daniel Marschall

  I have a beginner question about DNSSEC. I have much experience with TLS and cryptography-stuff and would like to try out this new technology. I have googled very much about this but I haven't found useful information for me. I think one confusion in information gathering is that "Debian howto DNSSEC setup" can mean "How to USE DNSSEC for resolving" OR "How to secure your domain with DNSSEC". I am searching the second. I am running a Debian Squeeze server with root privileges which has a domain name ending with ".de" (which is already signed by the root zone). The network interface at this server uses the gateway IP (DNS resolver?) of the datacentre the server is running on. My domain is hosted at freedns.afraid.org , where I can add DNS RRs for my domain. They are currently NOT capable of adding DNSSEC RRs, but I am bugging them to support this soon. ;-) My simple question is: How do I setup DNSSEC on Debian? Resp. who have I ask to? As far as I understand, all I have to do is to run dnssec-keygen on my Debian server and then add the key to my DNS-provider as DNSSEC RR. (And change it every 30 days?) I have looked at this http://www.isc.org/files/DNSSEC_in_6_minutes.pdf but it looks like you have to be the owner of a ZONE, so I don't think this applies to me. Who needs to sign my domain? My DNS-provider or my zone (DeNIC) or can I do it myself? Any help is very appreciated!

  Read the article

• Monitor reset itself and now I can't set the resolution/settings back to how it was before

  - by verve

  I've had my LG 24" widescreen monitor since 2009 and 2 weeks ago I noticed the monitor turned itself off (never had it done this before) so I switched it back on to find all the settings like gamma, resolution etc. different = looked like it had been reset. Everyone in the house swears they never unplugged and plugged it back in. When I opened a webpage the fonts and zoom on the pages were different and my desktop was strange too; fonts of the icons were different etc. The screen seems blurry and when I watch movies the faces look distorted so I thought I would try to first figure out the resolution it used to be but when I go under "Adjust screen resolution" none of the options work and there is no recommended resolution marked; all the options stretch out the screen and looks terrible so right now I have it set to the least distorted one. Then since the resolution wasn't working I set the other manual settings(done by physical buttons on the monitor) back to how it used to be (luckily, I had written these down). The monitor looks better but the resolution makes it a strain to use. I thought maybe some Windows update caused this crap so I tried to System Restore: didn't work. What went wrong? A few questions: 1) What was the likely cause of the monitor shutting down itself and screwing up the settings I have been using since the day I bought the monitor? 2) Why have the fonts changed everywhere unless this is a HDD/video card problem? 3) How do I find the perfect resolution it used to be? The monitor wants me to set it to 1920 x 1080 but that isn't one of the options although I don't remember what resolution I used before. I use the 16:9 setting while I try the available resolution options but nothing looks good! How do I find what it used to be? Manual available in PDF under Support: http://www.lg.com/ca_en/computer-products/monitors/LG-lcd-monitor-W2442PA-BF.jsp Win 7. IE 9.

  Read the article

• File permissions question

  - by Matthew Robert Keable

  I just switched my site's server from Windows to Linux, and am finally able to control file permissions from my ftp. So, seeing that all permissions were 705 by default (and not wanting just anyone to have permission to execute), I went and changed everything to 744. Now, gif and jpg links don't work, pdf download links don't work, php links don't load, and mov files don't play. Conversely, all html files work perfectly. Setting things back doesn't seem to help. Even setting to 777 gets me nowhere. Any ideas on what might be going wrong? I've been googling file permissions all day (solved that problem with the Windows-Linux switch, which has bred a new problem), and I don't think anything I can find has escaped my attention. The site: absis-minas.com Go easy on a n00b. I took up learning php out of interest, and wound up delving into server management issues due to a very simple line of code not working the way it was supposed to. Thanks!

  Read the article

• preformance wise htaccess

  - by purpler

  hese's the my htaccess template, i wonder if anything could be added to increase website performance.. # Defaults AddDefaultCharset UTF-8 DefaultLanguage en-US ServerSignature Off FileETag None Header unset ETag Options -MultiViews #Options All -Indexes # Force the latest IE version or ChromeFrame <IfModule mod_setenvif.c> <IfModule mod_headers.c> BrowserMatch MSIE ie Header set X-UA-Compatible "IE=Edge,chrome=1" env=ie </IfModule> </IfModule> # Proxy X-UA Setup <IfModule mod_headers.c> Header append Vary User-Agent </IfModule> #Rewrites Options +FollowSymlinks RewriteEngine On RewriteBase / # Redirect to non-WWW RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^(.*)$ http://%1/$1 [R=301,L] # Redirect to WWW RewriteCond %{HTTP_HOST} ^domain.com RewriteRule (.*) http://www.domain.com/$1 [R=301,L] # Redirect index to root RewriteRule ^(.*)index\.(php|html)$ /$1 [R=301,L] # Caching ExpiresActive On ExpiresDefault A0 Header set Cache-Control "public" # 1 Year Long Cache <FilesMatch "\.(flv|fla|ico|pdf|avi|mov|ppt|doc|mp3|wmv|wav|png|jpg|jpeg|gif|swf|js|css|ttf|eot|woff|svg|svgz)$"> ExpiresDefault A31622400 </FilesMatch> # Proxy Caching <FilesMatch "\.(css|js|png)$"> ExpiresDefault A31622400 Header set Cache-Control "private" </FilesMatch> # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Proper SVG serving AddType image/svg+xml svg svgz AddEncoding gzip svgz # GZip Compression <IfModule mod_deflate.c> <FilesMatch "\.(php|html|css|js|xml|txt|ttf|otf|eot|svg)$" > SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error page ErrorDocument 404 /404.html # Deny access to sensitive files <FilesMatch "\.(htaccess|ini|log|psd)$"> Order Allow,Deny Deny from all </FilesMatch>

  Read the article

• When did my LaTeX files become TeX files!?

  - by andrz_001

  After transferring all my files onto a new machine, all files that were once LaTeX files (having the texnic center "T" icon) are now TeX files (having the TeX works icon --I don't remember installing that one!). But....the files are associated with the technic center! In other words, the files open with the texnic center, yet the "type of file" is "tex document". I'm using the same miktex distrubution and texnicCenter (both for windows xp) as on the old machine. Again, I don't know how/where I got this texworks on the new machine--assuming it came with windows. A question: Could these tex associations cause me any new surprises, anything unexpected? Like certain packages not working, etc? Because I can't have that!! Should I not fix it if it ain't broken!? For instance, one particular file yesterday would not produce any pdf output after compiling...after trying many things (other files compiled as they should have), I got to thinking to try it without the setspace for doublespacing!! And it worked. I have no idea why. Anyway.... Real question: How to revert to LaTeX file associations?? Rhetorical question: Would this question have better luck in ctan or stackoverflow? I guess I'll find out! Thank you wholeheartedly!

  Read the article

• Hiera datatypes wont load in Puppet

  - by Cole Shores

  I have spent a couple of days on this, followed the instructions on http://downloads.puppetlabs.com/docs/puppetmanual.pdf and even the Puppet Training Advanced Puppet manual. When I run a test against it, the results always come back as 'nil' and Im not sure why. I am running Puppet 3.6.1 Community Edition, with Hiera 1.2.1 on SLES 11. My puppet.conf file at /etc/puppet/puppet.conf consists of: [main] # The Puppet log directory. # The default value is '$vardir/log'. logdir = /var/log/puppet # Where Puppet PID files are kept. # The default value is '$vardir/run'. rundir = /var/run/puppet # Where SSL certificates are kept. # The default value is '$confdir/ssl'. ssldir = $vardir/ssl certificate_revocation = false [master] hiera_config=/etc/puppet/hiera.yaml reporturl = http://puppet2.vvmedia.com/reports/upload ssl_client_header = SSL_CLIENT_S_DN ssl_client_verify_header = SSL_CLIENT_VERIFY # certname = dev-puppetmaster2.vvmedia.com # ca_name = 'dev-puppetmaster2.vvmedia.com' # facts_terminus = rest # inventory_server = localhost # ca = false [agent] # The file in which puppetd stores a list of the classes # associated with the retrieved configuratiion. Can be loaded in # the separate ``puppet`` executable using the ``--loadclasses`` # option. # The default value is '$confdir/classes.txt'. classfile = $vardir/classes.txt # Where puppetd caches the local configuration. An # extension indicating the cache format is added automatically. # The default value is '$confdir/localconfig'. localconfig = $vardir/localconfig my /etc/puppet/hiera.yaml consists of: :backends: yaml :yaml: :datadir: /etc/puppet/hieradata :hierarchy: - common - database I have a directory created in /etc/puppet/hieradata and within it contains: /etc/puppet/hieradata/common.yaml :nameserver: ["dnsserverfoo1", "dnsserverfoo2"] :smtp_server: relay.internalfoo.com :syslog_server: syslogfoo.com :logstash_shipper: logstashfoo.com :syslog_backup_nfs: nfsfoo:/vol/logs :auth_method: ldap :manage_root: true and /etc/puppet/hieradata/database.yaml :enable_graphital: true :mysql_server_package: MySQL-server :mysql_client_package: MySQL-client :allowed_groups_login: extranet_users does anyone have any idea what could be causing Hiera to not load the requested values? I have tried even restarting the Master. Thanks in advance, Cole

  Read the article

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• Issues with VPN functionality

  - by Xorandor

  I've been working on setting up VPN connectivity to our office location. We bought a Cisco WRV210 which have a builtin VPN server. Cisco has some software QuickVPN, which is not as quick and easy as I had thought. I've had mixed experiences on different machines with connecting. Instead I configured an IPSec VPN tunnel following a guide from TheGreenBow here http://www.thegreenbow.com/doc/tgbvpn_cg_linksys_wrv200_en.pdf I followed their instructions and tried out an evaluation of their software, and VPN connection should be working ok. I'm able to do RDP to a machine on the network (using IP address, not machine name) and ping the router etc. What I'm trying to solve are two things: It's not like I'm "really" on the network. Or at least I'm restricted to some degree when going through the VPN. I can't access a machine on the network using machine name, only IP. I can't ping a machine, but the router just fine. Could this be that something is not set up properly? If so, I can ofcourse supply additional information. Second, when I log onto the VPN, I would really like my outgoing connection to go through the internet connection of the remote location. Basically if I connect to the VPN I want my outgoing IP to be that of the remote location's (needed for some IP resctrictions on some of our servers). At a previous work location it worked like this when we connected to our office VPN over PPTP and the builtin windows VPN client. I'm not a huge expert on the topic, so any hints will be appreciated.

  Read the article

• Is it possible to change "working directory" of XeTeX?

  - by Herbert Sitz

  Using XeTeX there are many working files that get created in process of producing the pdf, and they litter the directory where my main .tex file is. Is it possible to change the working directory of XeTeX so that it stores all these scratch files in some other directory, out of the way? There is a previous question on Superuser.com that discusses a utility that cleans up the working files by deleting them after they're produced: http://superuser.com/questions/95712/how-to-avoid-littering-ones-tex-directories-with-intermediate-files That solution doesn't work for me since I'm using XeTeX, but also it seems like it would be preferable to simply be able to designate a "scratch" directory where all working files are saved. I haven't been able to find any info on how to do it though. Is there a way? (My question is prompted partly because of the fact that I often work with files in a directory that is shared using DropBox, so it creates a lot of unnecessary traffic if files are getting created and destroyed willy nilly. I don't know if it affects speed in any way, but the idea of having a separate working directory that is not shared/replicated by DropBox would be a cleaner solution, even if I could use the method suggested in the earlier thread.)

  Read the article

• What is the sysadmin's dream network printer? 6-8k pg/mo. Xerox, OkiData, Lexmark and HP are all fail

  - by Jacob

  How do I find out what printer brand and/or type doesn't suck? This information is hard to find and manufacturer's websites won't reveal any issues with certain printers. After 10 years of dealing with network shared printers, I can't say that I have been impressed with any of the printer brands I've seen. Brother's little laser MFPs have been close to ideal for low volume, but that is it, period. OkiData, Lexmark, HP, Xerox solid ink printers, they all sucked in one way or another. Currently I'm looking to replace a Xerox ColorQube 8570 because it fails to print on a regular basis. Sometimes it doesn't even boot VxWorks fully - it just hangs at 2% or whatever. I've used Xerox 8860MFPs and they sucked just as bad. I won't talk about ink jets here, that's most likely not what I'm looking for. We currently spend about $4k on paper and ink per year for this printer at up to 6-8k pages per month, letter, mostly black and white, low color usage. I want the printer to feed paper correctly, not crash and burn when a PDF isn't according to its taste (my favorite Xerox problem here) and with decent drivers for Windows and OS X. Print quality is not of the utmost importance but paper does get sent to customers.

  Read the article

• Disable CTRL+mouse wheel zooming in Chrome?

  - by Peter Nore

  I'm a normal-sighted person and I would like to view pages at 100% all the time. I use keyboard shortcuts that involve CTRL a lot, so about twenty times a day I accidentally hit CTRL at the same time that I'm scrolling, which results in the page being reflowed and repainted. This in is annoying because it can take up to 30 seconds to fix the issue, depending on how complex the site layout is. On sites with dynamic layout such as Google Docs the problem is more serious; accidentally hitting CTRL+mouse wheel corrupts the display and forces me to refresh the page entirely, sometimes causing me to loose information in the process. I would like to either decouple CTRL+mouse wheel from zoom, or disable zoom functionality altogether. This is possible on Firefox by using about:config; is there a similar way to edit detailed settings in Chrome? Would I have access to the detailed settings if I used Chromium instead of Chrome? I'll probably jump ship back to Firefox if I can't solve this problem. There is a superuser question that asks basically the same thing I'm asking, but for Firefox and Internet Explorer exclusively. Other people on the Chrome forum have had related issues, but none have the same problem. "I would really like it if I could deactivate the auto zoom in/out." had "something with laptops and Windows 7", not the feature built into Chrome. Other people have had PDF specific issues, which doesn't concern me. I've also tried searching for extensions that allow you to disable the scroll; I had hoped that "Zoom Lock" would have the ability to lock the zoom at 100% and prevent CTRL+scroll wheel from distorting the display, but it doesn't work for my use case. Google Chrome version 9.0.597.84 (Official Build 72991) Operating System: Ubuntu 10.10

  Read the article

• Dell Driver Support for Latitude E6320 Windows 7 Enterprise

  - by IamPolaris

  I recently did a reinstall of Windows 7 Enterprise on a Dell Latitude E6320, which is a 64 bit system. After the install process, and doing typical Windows Update stuff, I looked at my Device Manager and found that I had devices which were missing drivers. My missing drivers: After going to the Dell Support site and looking at the files, and doing some sleuthing I found the following support document: http://downloads.dell.com/utility/Latitude%20E-Family%20%20Mobile%20Precision%20Re-Image%20How-To%20Guide%20-%20A03%20Rev%203%200.pdf This document hints in appendix C that the Broadcom USH is the Control Point Security and the Unknown device is Micro freefall sensor. The network controller is my wireless, as I cannot connect wirelessly, and the final missing driver I am not sure. Attempting to install the control point security exe on the support page will not work. After downloading, I am given the message that I am attempting to install a 32 bit driver on a 64 bit machine EVEN THOUGH I selected the win7 64 bit option from the support page. Beyond that, some of the drivers (Which are confusing to read and hard to understand what they do) and the system utilities which are supposedly supposed to make this process simpler will either a) not run because they are 32 bit exe's or b) the support page cannot find the file attempted to download. Is there anything I can do to get (at the very least) my wireless running, but idealistically all of my drivers. A solution which assumes Dell is completely incompetent would be ideal. :P Some forums have said that I should download the chipset driver, others say to get the system utility file (DSS_UTIL_WIN_R282536.EXE). I have had no luck as of yet...

  Read the article

• SharePoint, Exchange and Incoming Emails Without Directory Management Services

  - by Nariman

  Trying to keep this as simple as possible. We've already created the email accounts that we need (e.g. account[1-20]@domain.com) on Exchange/AD. We'd like to now enable incoming emails on SharePoint 2007 lists corresponding to these accounts. My thinking is we don’t need to configure Directory Management Services [2] – the architecture will be simpler without it and the application doesn’t require these services. However, we still need to route messages from Exchange to either local SMTP services (via the connector described in the articles below) or by user-specific drop-folder settings (if permitted by Exchange). So the question is: can we instruct Exchange to use a drop folder just for accounts account[1-20]@domain.com? or do we need to change the accounts to account[1-20]@sharepointsmtp.domain.com and re-route those message to the local SMTP service that will drop them on disk? I've read the material below. [1] - http://www.combined-knowledge.com/Downloads/2007/How%20to%20configure%20Email%20Enabled%20Lists%20in%20Moss2007%20RTM%20using%20Exchange%202007.pdf http://social.msdn.microsoft.com/Forums/en/sharepointdevelopment/thread/91e0c3d2-afe6-469d-b1bc-6ae7a9aa287e http://gj80blogtech.blogspot.com/2009/12/configure-incoming-email-setting-in.html http://www.jasonslater.co.uk/2007/08/10/configuring-incoming-mail-on-moss-2007-and-exchange-2007/ http://technet.microsoft.com/en-us/library/cc262947%28office.12%29.aspx http://technet.microsoft.com/en-us/library/cc263260%28office.12%29.aspx [2] – http://graycloud.com/sharepoint/incoming-mail-configuration-what-permissions-are-require-t39483.html

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• nginx - proxy_pass is working - Apache isn't doing what it should...

  - by matthewsteiner

  So, I've got this in my nginx.conf: location ~* ^.+.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { root /var/www/vhosts/example.com/public/; access_log off; expires 30d; } location / { proxy_pass http://127.0.0.1:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } So anything that is a "static file" that exists will just be done with nginx. Otherwise, it should pass it off to Apache. Right now, static files are working correctly. However, if something is passed to apache and it's example.com or subdomain.example.com, apache just spits out the "Apache 2 Test Page" that you get if there's nothing there. Apache worked fine before, so I'm guessing it has to do with the way nginx is "asking". I'm not sure though. Any ideas?

  Read the article

• How to avoid index.php in Zend Framework route using Nginx rewrite

  - by Adam Benayoun

  I am trying to get rid of index.php from the default Zend Framework route. I think it should be corrected at the server level and not on the application. (Correct me if I am wrong, but I think doing it on the server side is more efficient). I run Nginx 0.7.1 and php-fpm 5.3.3 This is my nginx configuration server { listen *:80; server_name domain; root /path/to/http; index index.php; client_max_body_size 30m; location / { try_files $uri $uri/ /index.php?$args; } location /min { try_files $uri $uri/ /min/index.php?q=; } location /blog { try_files $uri $uri/ /blog/index.php; } location /apc { try_files $uri $uri/ /apc.php$args; } location ~ \.php { include /usr/local/etc/nginx/conf.d/params/fastcgi_params_local; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_param SERVER_NAME $http_host; fastcgi_pass 127.0.0.1:9000; } location ~* ^.+\.(ht|svn)$ { deny all; } # Static files location location ~* ^.+\.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { expires max; } } Basically www.domain.com/index.php/path/to/url and www.domain.com/path/to/url serves the same content. I'd like to fix this using nginx rewrite. Any help will be appreciated.

  Read the article

• Organizing automatically Windows Files and Folders

  - by Kiquenet

  For Windows only, Organizing the eleventy-billion files you've got stuffed into folders on your hard drive is very "hard". For example, I have one folder on my computer that I save all web downloads to, regardless of file type, size or purpose. Many of the files are only temporary downloads, for instance setup files of applications that I test, demonstration videos that I watch once or documents that I want to read. Some files on the other hand are there to stay, and I used to move them out of the download folder manually in the past. Another files in folders in my computer: many source code, tests, programs, tools, ... I need tecnology for organize billion files. Which best tools for organize, sort, etc automatically your files-folders? Digital Janitor http://davidevitelaru.com/software/digital-janitor/ Belverede http://lifehacker.com/5510961/how-to-automatically-clean-and-organize-your-desktop-downloads-and-other-folders Download Mover http://www.neoteo.com/download-mover-reorganiza-tus-descargas-14188 File/Folder Date Organizer http://seedling.dcmembers.com/other/ffdorg.zip DropIt http://www.lupopensuite.com/db/dropit.htm Others issues about organization files, desktop, etc How to automate the process of organizing audio files on Windows Organizing My Windows Desktop What's a good way for organizing PDF documents on Windows? Folksonomy tagging for files What is your method of “folksonomy” tagging for files on your local machine?

  Read the article

• Formula-based Excel page headers

  - by Jake Krohn

  I'm using the "Rows to repeat at top" function in Excel's "Page Setup" dialog to ensure that a multi-row header block appears on every printed page of my worksheet. However, I'd like to be able to change certain bits of the header based on the content of the current page. I would simply like to display the value of one cell in the first row that is printed on the page. If this is my header: Section: xx And the data looks like this (columns are Section and Name): 1 Foo 1 Bar 2 Baz I want the "xx" in the header to be "1". If, further down on the next page, the value in the Section column is "3", I want that printed in the header of the next page. I originally thought that using the "OFFSET" function might help, e.g. ="Section: "&OFFSET(A2, 1, 0) But it only shows the offset from the original placement of the header, thus only working on page 1. The end document is a PDF, so right now I'm able to go back in with the "TouchUp Text Tool" in Acrobat and add the numbers page by page. But it gets to be a tedious process with 70+ page reports. Anyone have any better ideas that don't require me mucking up the original Excel document with inserted headers every N lines? This is Excel 2008 for Mac, if it makes a difference.

  Read the article

• Outlook 2007 + Exchange 2010 (Save All Attachments)

  - by RobertPitt

  About 3 weeks back our company upgraded our mail system to Exchange 2010, all went smooth, few issues but nothing major. A few days ago we had a call from a colleague where he was unable to save all attachments, From File > Save As > Save All Attachments. When the email has a single attachment it works perfectly normal, and depending on the file type it allows you to save multiple attachments. But there's a lot of file types that will not work, such as zip, pdf, doc etc, Usually we get a location box open up asking where we would like to drop the attachments, but it does nothing, You click Save All Attachments and nothing happens. After hours of research I have come across mixed results, a lot of people on forums have been explaining that they have recently crossed over to Exchange 2010 and there issues started there. But on the other hand Microsoft released a KB (278188) which was depressing if that, but that article was published in 2007, as stated by the time stamp, and Exchange 2010 has only come out recently. Im looking to see if you guys have any clues what could be causing this, anything server side that I can take a look at (AD, Exchange, ...). Any help on this is greatly supported

  Read the article

• Application Virtualization

  - by Peter Versnee

  I have been looking for a solution to virtualize my desktop application as a SaaS. After picking Citrix XenApp as the best solution for my case and trying for ever to get it to work (with some more experienced people) I can't help but to conclude that Citrix has too much problems for my case. Every time I fix one thing some other thing pops up. As I can't imagine Citrix XenApp is the only way to deliver my application to my clients, I'd like to ask you experienced guys if you think there is an other way to deliver it whilst meeting my requirements. I've got no money issues - time on the other hand... My requirements: My application must run on a windows server; The application should be virtualized with the application window only (no desktop); Content Redirection (my application is the only one virtualized, so PDF, DOC(X) etc. is on the users' system); Easy user management; SSO;* Cross platform (Windows, Linux, Mac OSX).* I truly hope I don't annoy you with another of the same question. I've tried to find the same question here and - obviously - didn't found it. *) these I can live without, however very much appreciated

  Read the article

• Linux Cups raspberry pi offload processing to server

  - by jaredmsaul

  I am interested in setting up a raspberry pi as the local end of a printing solution. In my testing the pi chokes on acting as a complete cups based print server. It seems a little underpowered for some of the ghostscipt processing and other filtering that occurs-- particularly on larger or complex documents the processing time can be 5 or more minutes. My question is can the processing be largely done elsewhere and the prepared end product of the processing chain be fed to the pi for output on the connected printer? So in this scenario any arbitrary document (html, pdf, text) is initially 'printed' on a relatively powerful machine but the output is stored in a file. This file is then grabbed by the pi and with all the heavy work out of the way easily printed using cups. I know files can be pushed through cups in raw mode but I am fuzzy on the pros and cons and the applicability in what I describe. I have tested this with pdftops creating a ps file then feeding that raw to cups and I think it works but it seems like there may be a cleaner solution. This scenario would ideally work for any number of printer types.

  Read the article

• Print over remote CUPS server, but just show a subset of the printers.

  - by jdm

  I'd like to print from my Ubuntu laptop (karmic) to some networked printers. Our organisation uses a CUPS server with several hundred printers. What I know I can do is: CUPS_SERVER=printers.company.com acroread document.pdf and then Adobe Reader shows me all available printers to select from. However, it takes a couple of minutes to display the large list, which is really annoying. (The desktop PCs here suffer from this, too.) The other option is to add a new printer with an address like ipp://printers.company.com/printer/bldg1_hp8150 (to the Ubuntu printer configuration = local CUPS server). However, it asks me for a driver. I don't want to / can't always specify a driver, since some printers don't appear in the list. I'd like to let the remote CUPS server handle the driver part (like it does when i set CUPS_SERVER), and do no more preprocessing/"driver stuff" on my side. The ideal thing would be if I could somehow add the remote printer list to my local cups server, and apply a filter, so that it would just display printers a la bldg1_*. This feature was available in KDE3.?, but I can't find something similar in Ubuntu/Gnome. Any suggestions?

  Read the article

• nginx giving 404 when accessing php from alias directory

  - by code90

  I am trying to migrate from apache to nginx. The php sites that I am hosting need to access a shared library which turns out to be an alias directory. Below is the configuration I came up with. html files work fine, but php files giving 404. I have read through and tried most (if not all) of the answers to the similar questions with no any success. Any hint on what might be causing the issue in my case? location /wtlib/ { alias /var/www/shared/wtlib_4/; index index.php; } location ~ /wtlib/.*\.php$ { alias /var/www/shared/wtlib_4/; try_files $uri =404; if ($fastcgi_script_name ~ /wtlib(/.*\.php)$) { set $valid_fastcgi_script_name $1; } fastcgi_pass 127.0.0.1:9013; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/shared/wtlib_4$valid_fastcgi_script_name; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; } Thanks all ! Update: Following seems to be working fine: location /wtlib/ { alias /usr/share/php/wtlib_4/; location ~* .*\.php$ { try_files $uri @php_wtlib; } location ~* \.(html|htm|js|css|png|jpg|jpeg|gif|ico|pdf|zip|rar|air)$ { expires 7d; access_log off; } } location @php_wtlib { if ($fastcgi_script_name ~ /wtlib(/.*\.php)$) { set $valid_fastcgi_script_name $1; } fastcgi_pass $byr_pass; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/php/wtlib_4$valid_fastcgi_script_name; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; }

  Read the article

• LighTPD and PHP not working if outside of LightTPD folder

  - by Marco83

  I need to set up a simple web server with PHP on Windows XP that a number of different people will use for local testing. I'm using LightTPD 1.4.30-4-IPv6-Win32-SSL and PHP 5.2. So far I've created this folder structure: tools/ LightTPD/ htdocs/ PHP/ I set up PHP as CGI and the document root as server_root + "/htdocs". It works fine (well, it's slow but I don't want to bother with FastCGI for now :) ). My problem is when I try to put the htdocs outside of LightTPD folder, like this: htdocs/ tools/ LightTPD/ PHP/ I update the document root to server_root + "/../../htdocs" and while static HTML pages work fine, PHP pages stop working (they return a "No input file specified"). I literally just change the document root, I didn't change anything in the php.ini or anywhere else. Please also note that I left all doc_root, user_dir and cgi.force_redirect to the default values in php.ini, and it works when htdocs is inside LightTPD, but not when I move it ouside. Any idea of why it's breaking?? Here's my lightTPD.conf: server.modules = ( "mod_access", "mod_accesslog", "mod_alias", "mod_cgi", "mod_status", ) include "variables.conf" include "mimetype.conf" # THIS WORKS server.document-root = server_root + "/htdocs" # THIS DOESN'T #server.document-root = server_root + "/../../htdocs" server.upload-dirs = ( temp_dir ) index-file.names = ( "index.php", "index.pl", "index.cgi", "index.cml", "index.html", "index.htm", "default.htm" ) server.event-handler = "libev" url.access-deny = ( "~", ".inc" ) $HTTP["url"] =~ "\.pdf$" { server.range-requests = "disable" } static-file.exclude-extensions = ( ".php", ".pl", ".cgi" ) server.errorlog = server_root + "/logs/error.log" ######### Options that are good to be but not neccesary to be changed ####### dir-listing.activate = "enable" #### CGI module cgi.assign = ( ".php" => server_root + "/../PHP/php-cgi.exe" ) status.status-url = "/server-status" status.config-url = "/server-config"

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >