Search Results

Search found 4839 results on 194 pages for 'xfce panel'.

Page 178/194 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• Cant access a remote server due mistake by setting firewall rule

  - by LMIT

  I need help due a my silly mistake! So for long time i have a dedicate server hosted by register.it Usually i access remotly to this server (Windows 2008 server) by Terminal Server. Today i wanted to block one site that continually send request to my server. So i was adding a new rule in the firewall (the native firewall on windows 2008 server), as i did many time, but this time, probably i was sleeping with my brain i add a general rules that stop everything! So i cant access to the server anymore, as no any users can browse the sites, nothing is working because this rule block everything. I know that is a silly mistake, no need to tell me :) so please what i can do ? The only 1 thing that my provider let me is reboot the server by his control panel, but this not help me in any way because the firewall block me again. i have administrator username and password, so what i really can do ? there are some trick some tecnique, some expert guru that can help me in this very bad situation ? UPDATE i follow the Tony suggest and i did a NMAP to check if some ports are open but look like all closed: NMAP RESULT Starting Nmap 6.00 ( http://nmap.org ) at 2012-05-29 22:32 W. Europe Daylight Time NSE: Loaded 93 scripts for scanning. NSE: Script Pre-scanning. Initiating Parallel DNS resolution of 1 host. at 22:32 Completed Parallel DNS resolution of 1 host. at 22:33, 13.00s elapsed Initiating SYN Stealth Scan at 22:33 Scanning xxx.xxx.xxx.xxx [1000 ports] SYN Stealth Scan Timing: About 29.00% done; ETC: 22:34 (0:01:16 remaining) SYN Stealth Scan Timing: About 58.00% done; ETC: 22:34 (0:00:44 remaining) Completed SYN Stealth Scan at 22:34, 104.39s elapsed (1000 total ports) Initiating Service scan at 22:34 Initiating OS detection (try #1) against xxx.xxx.xxx.xxx Retrying OS detection (try #2) against xxx.xxx.xxx.xxx Initiating Traceroute at 22:34 Completed Traceroute at 22:35, 6.27s elapsed Initiating Parallel DNS resolution of 11 hosts. at 22:35 Completed Parallel DNS resolution of 11 hosts. at 22:35, 13.00s elapsed NSE: Script scanning xxx.xxx.xxx.xxx. Initiating NSE at 22:35 Completed NSE at 22:35, 0.00s elapsed Nmap scan report for xxx.xxx.xxx.xxx Host is up. All 1000 scanned ports on xxx.xxx.xxx.xxx are filtered Too many fingerprints match this host to give specific OS details TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 ... ... ... 13 ... 30 NSE: Script Post-scanning. Read data files from: D:\Program Files\Nmap OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 145.08 seconds Raw packets sent: 2116 (96.576KB) | Rcvd: 61 (4.082KB) Question: The provider locally can access by username and password ?

  Read the article

• Why do I have multiple drives in my backup system image?

  - by bebop

  I have a drive which has 2 partitions. One is where the OS is installed, the other is a data (but not libraries) drive. When I try and create a backup using the built in tool, it wants to include both partitions in the system image. Why does it do this? If I move the os to a separate drive will I be able to back up just this data? Edit: To be more clear. I have 4 disks in the machine. 1 disc has 2 partitions. These are c: and e:, the other disks are d: f: and h:. The OS is installed on c: and libraries are stored on h:. The libraries are already backed up using crashplan, but I want to create a system image so I can easily restore the machine, if it either dies or if I get a SSD drive. When I choose backup (either through the wizard or if I open it through control panel) and check (or click) create a system image it automatically adds both c: and e: to the list of drives that will be backed up, and I cannot change this, the checkboxes to unselect are greyed out. I would like to know why it automatically adds e: to the list (but not h:, where the libraries are) and if I can change some setting so whatever files it has on e: that it thinks need to be backed up as part of the system image are moved to c:. How can I determine what they are? Is it because c: and e: are partitions of the same disk? If I move c: tro a different disk will that mean I only have to back up c:? Thanks Edit 2: I have viewed all files including hidden and system ones on both drives and it seems that I have a suspicous hidden e:\boot\ folder. I think that I might have installed the OS as a VHD at first then installed a seperate version straight on the disk, having dual boot for a while, then used EasyBCD to remove the VHD boot and file. Might this be what is causing my issue? How might I go about removing this? is it safe to just delete the boot folder?

  Read the article

• why can't I open a port on Win 7? is it the app's fault?

  - by rjnagle

  I am having problems opening a port from one Windows PC on my local network. On Windows 7 computer ("Computer A") I running Calibre, an ebook management program that has something called an "ebook content server" . In essence, it serves via the web a content catalog. From Computer A, I can access the content server on localhost. ie. http://127.0.0.1:8787 calls up the content server successfully. With ipconfig I have confirmed that its local IP address is 192.168.1.106 From Computer B (a Vista Machine) I can ping 192.168.1.106 I have tried opening/editing a port in the Windows Firewall several times. In Windows firewall -- Allowed Programs in Control Panel, I see a listing for Calibre (with both Home/Work and PUblic checked) In details, I see Name: Calibre, Port Number 8787, Protocol TCP If I use the Advanced Security configuration screen for the firewall, I created an Inbound Rule on Computer A for Calibre (with the settings I indicated). If I run this command line on Computer A, I see: netstat -a -n TCP 0.0.0.0:554 0.0.0.0:0 LISTENING TCP 0.0.0.0:664 0.0.0.0:0 LISTENING TCP 0.0.0.0:2869 0.0.0.0:0 LISTENING TCP 0.0.0.0:3306 0.0.0.0:0 LISTENING TCP 0.0.0.0:5357 0.0.0.0:0 LISTENING TCP 0.0.0.0:6570 0.0.0.0:0 LISTENING TCP 0.0.0.0:6580 0.0.0.0:0 LISTENING TCP 0.0.0.0:8787 0.0.0.0:0 LISTENING TCP 0.0.0.0:10243 0.0.0.0:0 LISTENING TCP 192.168.1.106:63020 74.125.227.51:80 TIME_WAIT TCP [::]:80 [::]:0 LISTENING TCP [::]:135 [::]:0 LISTENING TCP [::]:443 [::]:0 LISTENING TCP [::]:445 [::]:0 LISTENING TCP [::]:554 [::]:0 LISTENING TCP [::]:2869 [::]:0 LISTENING TCP [::]:5357 [::]:0 LISTENING TCP [::]:6570 [::]:0 LISTENING TCP [::]:6580 [::]:0 LISTENING TCP [::]:10243 [::]:0 LISTENING TCP [::]:49152 [::]:0 LISTENING TCP [::]:49153 [::]:0 LISTENING TCP [::]:49154 [::]:0 LISTENING TCP [::]:49155 [::]:0 LISTENING TCP [::]:49170 [::]:0 LISTENING And lots of other junk, but this seems relevant, I see port 80 is open (I run xampp apache web server for windows on Machine A) This is the only time I see port 8787 referenced from the netstat commmand. From Windows Computer B, I can, ping 192.168.1.106 and even view http://drupal.local (on Computer A) and http://192.168.1.106/ (which goes to the Xampp config screen on Computer A). But I cannot access via Computer B htttp://192.168.1.106:8787 or htttp://computerhosta:8787 So what is going wrong? Is this a problem with the Calibre application or have I incorrectly opened the port? What things could possibly interfere with the opening of this port? On a sidenote, I have tried using telnet from Computer B to see if port 80 or 8787 is open for 192.168.1.106. I get no reply for either one. Thanks.

  Read the article

• What are some fast methods for navigating to frequently used folders in Windows 7?

  - by fostandy

  (This is a followup question from my previous question.) In windows XP I used to be able to quickly navigate to frequently used folders by making use of the 'Favorites' menu item and the hotkey behaviour. In certain conditions it could be set up so that getting to a particular folder was as easy as alt-a x (and without a file explorer window open it was as fast as win-e alt-a x). I am struggling to get anywhere near this speed in Windows 7 and would like to solicit advice from others regarding fast folder navigation to see if I am missing any methods. My current way to navigate quickly is basically move hand to mouse move cursor to navigation pane/pain. scroll all the way to the top (because normally I the panel is focused on whatever deep directory structure I am already in). sift through my 50+ favorites to get the one I want, or click a link to a folder that contains further links in some sort of 'pseudo-tree' functionality. select it. This is slower than my previous method by upwards of an order of magnitude. There are a couple of things I've contemplated: add expandable folders, not just direct links, to the favorites menu. add expandable folders, not just direct links, to the start menu. add links of my favorite folders to a submenu of the start menu so that they come up when I search them. They do but this still rather cumbersome started using 7stacks - url here (I cannot link the url directly due to lack of reputation but http://www.alastria.com/index.php?p=software-7s). This is about the closest I've gotten to some sort of compact, customizeable, easy to access, tree based navigation structure. How do you power users quickly navigate to your favorite folders? Are there keyboard shortcuts I am missing? Can someone recommend other apps or addon or extensions that can achieve this sort of functionality? The Current solution (thanks to the answers below) I am going to use is a combination of Autohotkey and 7stacks - autohotkey to launch 7stacks, 7stacks with the 'menu' stack type for fast, key-enabled navigation to folders organised in a tree structure. This solves about 90% of the issue, the only issues are (note that these are really minor, I am really splitting hairs more than anything here) Can't use this for existing folder navigation (ie already have a explorer window open, want to go to another directory) A bit more cumbersome to add/remove entries to compared to xp favorites. A little slower than xp favorites. Whatever. I'm happy. Thanks guys. I think the answer is a split to John T and Kelbizzle - I've elected to give the answer to John T and +1 to Kelbizzle as I had already mentioned 7stacks.

  Read the article

• SQL server 2008 R2 installation error

  - by Sonia

  I have a windows 7,32 bit laptop. I am the administrator with all permissions. when I click on the SQL server 2008R2 set up file,it says : "SQL server set up has encountered the following error:Failed to retreive data for this request" click on OK. I have uninstalled all the components of SQL from control panel. I used Windows installer clean up to remove the files(which I must have not done ),but still no go. The summary.txt log says: Overall summary: Final result: Failed: see details below Exit code (Decimal): 847168662 Exit facility code: 638 Exit error code: 50326 Exit message: Failed to retrieve data for this request. Start time: 2012-05-25 14:59:15 End time: 2012-05-25 15:00:09 Requested action: RunRules Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\Detail.txt Exception help link: http%3a%2f%2fgo.microsoft.com%2ffwlink%3fLinkId%3d20476%26ProdName%3dMicrosoft%2bSQL%2bServer%26EvtSrc%3dsetup.rll%26EvtID%3d50000%26ProdVer%3d10.0.5500.0%26EvtType%3d0xEF814B06%400x92D13C14 Machine Properties: Machine name: EWAN-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: Australia OS language: English (United States) OS architecture: x86 Process architecture: 32 Bit OS clustered: No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation location: c:\385030d65c6ff61fb9\x86\setup\ Installation edition: EXPRESS User Input Settings: ACTION: RunRules CONFIGURATIONFILE: FEATURES: HELP: False INDICATEPROGRESS: False INSTANCENAME: QUIET: False QUIETSIMPLE: False RULES: GLOBALRULES,SqlUnsupportedProductBlocker,PerfMonCounterNotCorruptedCheck,Bids2005InstalledCheck,BlockInstallSxS,AclPermissionsFacet,FacetDomainControllerCheck,SSMS_IsInternetConnected,FacetWOW64PlatformCheck,FacetPowerShellCheck X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\ConfigurationFile.ini Detailed results: Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: The rule result report file is not available. Exception summary: The following is an exception stack listing the exceptions in outermost to innermost order Inner exceptions are being indented Exception type: Microsoft.SqlServer.Management.Sdk.Sfc.EnumeratorException Message: Failed to retrieve data for this request. Data: HelpLink.ProdName = Microsoft SQL Server HelpLink.BaseHelpUrl = http://go.microsoft.com/fwlink HelpLink.LinkId = 20476 DisableWatson = true Stack: at Microsoft.SqlServer.Setup.Chainer.Workflow.PendingActions.InvokeActions(WorkflowObject metaDb, TextWriter loggingStream) at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionEngine.RunActionQueue() at Microsoft.SqlServer.Setup.Chainer.Workflow.Workflow.RunWorkflow(HandleInternalException exceptionHandler) at Microsoft.SqlServer.Chainer.Setup.Setup.RunRequestedWorkflow() at Microsoft.SqlServer.Chainer.Setup.Setup.Run() at Microsoft.SqlServer.Chainer.Setup.Setup.Start() at Microsoft.SqlServer.Chainer.Setup.Setup.Main() Inner exception type: Microsoft.SqlServer.Configuration.Sco.ScoException Message: Attempted to perform an unauthorized operation. Data: WatsonData = HKEY_LOCAL_MACHINE@SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Microsoft SQL Server 10 Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Configuration.Sco.SqlRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Discovery.RegistryKeyExistsPropertyValueProvider.GetPropertyValue(Object[] context) at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.GetPropertyValueFromProvider(IPropertyValueProvider propertyValueProvider, String machineName, Object[] context) at Microsoft.SqlServer.Discovery.ObjectInstanceSettings.IsObjectFound(String machineName, String idFilter) at Microsoft.SqlServer.Discovery.Product.FilterObjectSet(ArrayList objects, String idFilter) at Microsoft.SqlServer.Discovery.Product.GetData(EnumResult erParent) at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData() at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData(Request req, Object ci) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.GetData(Object connectionInfo, Request request) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request) Inner exception type: System.UnauthorizedAccessException Message: Attempted to perform an unauthorized operation. Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) Ineed to install SQL server 2008 R2 for one of the company softwares to work. Any immediate help will be greatly appreciated. Thanks Sonia

  Read the article

• Optical SPDIF audio from motherboard not working with receiver

  - by simon b

  Hi, I hope someone can help; I can't get my SPDIF optical out working through my receiver and all the responses I can see on the web assume you have a sound card, while I settled for the (seemingly high end) sound on my motherboard (Asus P7P55D-E PRO), which appears to limit some of my options. My set-up is a "new out of the box" one and is: *Windows 7 PC (using PowerDVD10 for DVDs/Blurays and Windows media player for music) *Asus P7P55D-E PRO motherboard - has 8-channel audio TRS jacks and SPDIF optical and coaxial out *An old Yamaha receiver, whose only multi-channel input options are optical in and 6 channel RCA in. However, it still can handle DTS and DD *Boston Acoustic Soundware XS 5.1 speakers I've currently got the SPDIF optical out from the motherboard connected to the in on my receiver, have SPDIF enabled in the sound menu and the light is glowing red down the fibre. But I'm getting no sound at all. What I want is to be able to play DVDs/BluRays in 5.1 but also to be able to play music in multi-channel mode (even though I know this will be "fake" multichannel; it's more about where I sit in the room and my requirement to use the sub because the Boston is a satellite/sub set-up) My questions are: *Will optical work at all for multi-channel? THe latest posts I can see suggest it does but some people seem to say optical only outputs stereo. Whom to believe? *Even if it does work, I've read that I have to disable AC-3 decoding, or make various other changes, which don't seem to be possible without the menu options that a sound-card brings. Is the motherboard-only option just too inflexible? *Although my SPDIF device is enabled in the sound menu, it insists under "Jack information" that it is a "rear panel RCA jack", when of course it is not (both TOSLINK and rCA jacks do exist). Has the PC just forgotten that it has an optical? *I think I could relatively easily connect the 8-channel 3.5mm TRS jacks to my receiver 6-ch input jacks by way of TRS/RCA cables, but would that not stop me from being able to play music from media-player in multi-channel mode, as I'm not sure the motherboard can cope *Or do I need to bite the bullet and buy a sound-card? And if so, how can I be sure the one I get doesn't have the same problem? Any thoughts gratefully received, Cheers, simon

  Read the article

• Permissions problems with Apache / SVN

  - by Fred Wuerges

  I am installed a SVN server (v1.6) on a VPS contracted with CentOS 5, Apache 2.2 with WHM panel. I installed and configured all necessary modules and am able to create and access repositories via my web browser normally. The problem: I can not commit or import anything, always return permission errors: First error: Can not open file '/var/www/svn/test/db/txn-current-lock': Permission denied After fix the previous error: Can't open '/var/www/svn/test/db/tempfile.tmp': Permission denied And other... (and happends many others) Can't open file '/var/www/svn/test/db/txn-protorevs/0-1m.rev': Permission denied I've read and executed permissions on numerous tutorials regarding this errors, all without success. I've defined the owner as apache or nobody and different permissions for folders and files. I'm using TortoiseSVN to connect to the server. Some information that may find useful: I'm trying to perform commit through an external HTTP connection, like: svn commit http://example.com/svn/test SELinux is disabled. sestatus returns SELinux status: disabled Running the command to see the active processes of Apache, some processes are left with user/group "nobody". I tried changing the settings of Apache to not run with that user/group, but all my websites stopped working, returning this error: Forbidden You don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request. Apache process list: root@vps [/var/www]# ps aux | egrep '(apache|httpd)' root 19904 0.0 4.4 133972 35056 ? Ss 16:58 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 20401 0.0 3.5 133972 27772 ? S 17:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL root 20409 0.0 3.4 133972 27112 ? S 17:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 20410 0.0 3.8 190040 30412 ? Sl 17:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 20412 0.0 3.9 190344 30944 ? Sl 17:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 20414 0.0 4.4 190160 35364 ? Sl 17:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 20416 0.0 4.0 190980 32108 ? Sl 17:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 20418 0.3 5.3 263028 42328 ? Sl 17:01 0:12 /usr/local/apache/bin/httpd -k start -DSSL root 32409 0.0 0.1 7212 816 pts/0 R+ 17:54 0:00 egrep (apache|httpd) SVN folder permission var/www/: drwxrwxr-x 3 apache apache 4096 Dec 11 16:41 svn/ Repository permission var/www/svn/: drwxrwxr-x 6 apache apache 4096 Dec 11 16:41 test/ Internal folders of repository var/www/svn/test: drwxrwxr-x 2 apache apache 4096 Dec 11 16:41 conf/ drwxrwxr-x 6 apache apache 4096 Dec 11 16:41 db/ -rwxrwxr-x 1 apache apache 2 Dec 11 16:41 format* drwxrwxr-x 2 apache apache 4096 Dec 11 16:41 hooks/ drwxrwxr-x 2 apache apache 4096 Dec 11 16:41 locks/ -rwxrwxr-x 1 apache apache 229 Dec 11 16:41 README.txt*

  Read the article

• How to stop a random ramp in FCGI Processes Killing the server

  - by Andy Main

  So got the below earlier to day... Around that time the logs show a ramp in processes(600) and associated memory (1.2g), cpu usage load average (80) untill the server gave out. Server had to be hard reset by host as there was no ssh or plesk panel access. Fast CGI is configured as below and is setup for one high use site. As I understand it FcgidMaxProcesses 20 should protect against what happen but has not. I've read many forums with differing answers and references to many different fcgi directives, but have found nothing conclusive. Any one got some definitive answers on how to stop this sort of server process ramping and subsequent server failure? If you need more info let me know. Cheers Andy  /var/log/apache2/error_log [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17651 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17650 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17649 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17644 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17643 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17638 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17633 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17627 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17622 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17674 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17673 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17672 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17667 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17666 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17665 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17664 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17659 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17658 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17657 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17656 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17651 graceful kill fail, sending SIGKILL https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VRmFLWEZfR2VBb2M https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VWTcwZEhoV2Fqejg https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VUUtVWWFINHZjZ0U https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VZEVMclh6ZUdaOUE <IfModule mod_fcgid.c> <IfModule !mod_fastcgi.c> AddHandler fcgid-script fcg fcgi fpl </IfModule> FcgidIPCDir /var/lib/apache2/fcgid/sock FcgidProcessTableFile /var/lib/apache2/fcgid/shm FcgidIdleTimeout 40 FcgidProcessLifeTime 30 FcgidMaxProcesses 20 FcgidMaxProcessesPerClass 20 FcgidMinProcessesPerClass 0 FcgidConnectTimeout 30 FcgidIOTimeout 120 FcgidInitialEnv RAILS_ENV production FcgidIdleScanInterval 10 FcgidMaxRequestLen 1073741824 </IfModule>

  Read the article

• Unable to connect to SVN server on VPS : Subversion Configuration Problem

  - by Pritam Barhate

  Hello everybody, I purchased a VPS account (centos-5-x86_64) from Hostgator mainly for the purpose of setting up an online Subversion Server. This is the first time I am managing a VPS and my linux skills are not so great, but I have basic knowledge of the OS and have been using it on and off as desktop from last few years. So after foxing through a few tutorials online, as the first step I logged in using SSH root account provided by Hostgator and tried to run, yum install mod_dav_svn subversion As it turns out my account has Cpanel/WHM and since it some concept of easy apache straight forward procedure of yum install mod_dav_svn subversion won't work. After that I found out how it can be worked out by compiling the source and stuff. But the whole procedure looked long and scary. [I am just a linux nub]. so I decided I would just skip whole apache integration stuff and just access the server using svn:// protocol, anyways that's how I configure svn on our LAN. So I installed subversion using yum install subversion It installed fine. Then I created a folder /svn_repos/testproject and ran svnadmin create /svn_repos/testproject/ No Problems Using vi I changed svnserve.conf and passwd files for the repository and added a user with my name. Anonymous users don't have any access, authenticated users have write access. Then I started svnserve using svnserve -d then in same terminal window svn list svn://localhost/svn_repos/testproject Asks for authentication for realm, provided root password then for svn username and password. Provided both. The command returns nothing but exists properly. Returns nothing is understood I didn't import anything. But if try to access svn remotely using in another terminal: svn list svn://ip.add.of.server/svn_repos/testproject svn: Can't connect to host 'ip.add.of.server': Operation timed out Is what I get. Parallels Power Panel that I got from Hostgator reports that: The firewall is not active now. To activate the firewall, choose one of the firewall operation modes. So if firewall is not running and I can access svn using localhost, why the operation is timing out when I try to access svn from a remote machine? Experienced network admins please help. Thanks in advance. Also please suggest a good book which gives detailed information on configuring Dedicated servers + WHM and CPanel.

  Read the article

• Looking for a fiber optic "switch" or "router" for home use

  - by Shrout1

  The gist of my question: What is a "fiber optic" switch called? I.E. a layer 2 ethernet switch that uses fiber TX and RX connections and sends layer 2 network traffic between the fiber strands that are connected. Can someone purchase a dedicated fiber switch that does not have copper ethernet ports? What is the current average price of a device like this? Not necessarily looking for product endorsements, just information Might not make sense to go this route if it is too cost prohibitive What type of fiber connector is used for terminating a fiber strand into a jack on the wall? Can fiber be "patched" using two jacks and a "patch" cable? Is signal loss a concern with the longest runs at 100-200ft, a patch cable and media converters? The full story: My parents had unterminated fiber optic cable and terminated Cat5e run throughout their home when it was built in 2004. 10 years later the Cat5e isn't providing the throughput that my father needs to accomplish multiple streams of HD and fast system backups throughout the house. He can't reach gigabit speeds across the distance of the Cat5e runs. We are both interested in terminating the fiber connections and using them as high speed "backbones" to copper switches in each room of the house. It would be easy to attain gigabit speeds (or better, eventually) using the fiber. I have searched and searched for a "fiber optic switch" or "fiber optic router" and cannot find the correct term to describe this piece of hardware. We can use fiber media converters at the end points of each connection, however it would be nice to have a "patch panel" set up in the network closet in the basement that has fiber connections on it and switches the ethernet streams between the connections/systems in the house. Each fiber media converter costs between $50-$100 a piece... After 10 or so terminated connections it might make sense to find a piece of hardware that does not require media converters. That would depend upon the cost of this hardware Somewhat unrelated, if we are able to route between these fiber strands successfully, what is the physical connector type used in a jack on the wall? Just like RJ45 has a wall outlet (depicted below): What is the fiber optic equivalent of this? In the interim could we "patch" a couple fiber strands together in the network closet? Would signal loss be of concern with a run length of 100-200 feet, a patch cable and two media converters? If that would work then it could be used until the funds are available for more.

  Read the article

• How to add IP range to a server?

  - by Efe Cakinberk

  Hello, First of all I must say that I'm ver inexperienced server and network user. But I rented a unmanaged dedicated server. Well I didn't know what unmanaged really means, then I learned it when I needed support. Well I must do everything by myself. I have a problem. I had already 4 IPs on my server when I rented it. But then I needed more Ips and my server assigned me 32 Ips in which I can only use 27 of them. 85.25.230.0 - 85.25.230.31 this is my Ip range and they say the following Ips must not be configured on the server: 85.25.230.0 - network address 85.25.230.1 - gateway address 85.25.230.2 - router redundancy 85.25.230.3 - router redundancy 85.25.230.31 - broadcast address But the problem is ok Ips are assigned to me but they are not setup on my server. How will I setup Ips to work on my server? I did this after my reseach on google: I used this command on command prompt: route add 85.25.230.0 mask 255.255.255.224 85.25.230.1 metric 1 if then it said OK!. and I thought they should be working. (btw, mask is given to me by my ISP and I don't know metric 1 and if means I just saw it on the net and write it here) I setup my domains via using Plesk Kontrol Panel. So i added one domain and setup one of my new Ips 85.25.230.5 to it. But no it is not working. When I visit the domain via browser, there is a Plesk page comes and says this domain is not configured on the server. Then I changed the domains Ip to one of my old Ips which are given to me with the server and which I have been using for my other domains for a long time. Ok in a second, domain started working. I set it back to my new Ip and domain did not work. As I said, I'm not an expert and do not now the logic. But I'm eager to learn. Can you tell me what might couse the problem and did I do wrong while setting up IP RANGE to my server, if so how can I set them up? Thank you, Efe

  Read the article

• Installing Yaws server on Ubuntu 12.04 (Using a cloud service)

  - by Lee Torres

  I'm trying to get a Yaws web server working on a cloud service (Amazon AWS). I've compilled and installed a local copy on the server. My problem is that I can't get Yaws to run while running on either port 8000 or port 80. I have the following configuration in yaws.conf: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true This produces the following successful launch/result: Eshell V5.8.5 (abort with ^G) =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Using config file /home/ubuntu/yaws.conf =INFO REPORT==== 16-Sep-2012::17:21:06 === Ctlfile : /home/ubuntu/.yaws/yaws/default/CTL =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:8000 for <3> virtual servers: - http://domU-12-31-39-0B-1A-F6:8000 under /home/ubuntu/yaws/www/trial - =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:4443 for <1> virtual servers: - When I try to access the the url (http://ec2-72-44-47-235.compute-1.amazonaws.com), it never connects. I've tried using paping to check if port 80 or 8000 is open(http://code.google.com/p/paping/) and I get a "Host can not be resolved" error, so obviously something isn't working. I've also tried setting the yaws.conf so its at Port 80, appearing like this: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true and I get the following error: =ERROR REPORT==== 16-Sep-2012::17:24:47 === Yaws: Failed to listen 0.0.0.0:80 : {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Can't listen to socket: {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =INFO REPORT==== 16-Sep-2012::17:24:47 === application: yaws exited: {shutdown,{yaws_app,start,[normal,[]]}} type: permanent {"Kernel pid terminated",application_controller," {application_start_failure,yaws,>>>>>>{shutdown,>{yaws_app,start,[normal,[]]}}}"} I've also opened up the port 80 using iptables. Running sudo iptables -L gives this output: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- ip-192-168-2-0.ec2.internal ip-192-168-2-16.ec2.internal tcp dpt:http ACCEPT tcp -- 0.0.0.0 anywhere tcp dpt:http ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination In addition, I've gone to the security group panel in the Amazon AWS configuration area, and add ports 80, 8000, and 8080 to ip source 0.0.0.0 Please note: if you try to access the URL of the virtual server now, it likely won't connect because I'm not running currently running the yaws daemon. I've tested it when I've run yaws either through yaws or yaws -i Thanks for the patience

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubu

  - by user37968

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• How might I stop BACKSCATTER using Qmail?

  - by alecb

  New to ServerFault , please pardon if my details are too much Linux box acting as Virtual Host for domain hosting. Runs CentOs. Runs Parallels Plesk 9.x Regardless of the following, the SPAM keeps flowing in at 1-3 / second. An explanation of the problem... "xinetd service listens for SMTP connections and forwards to qmail-smtpd. The qmail service only process the queue, but does not control messages coming into the queue...that's why stopping it has no effect. If you stop xinetd AND qmail, then kill any open qmail-smtpd processes, all mail flow comes to a stop SOMETIMES Problem is, qmail-smtpd is not smart enough to check for valid mailboxes on the localhost before accepting the mail. So, it accepts bad mail with a forged replyto address which gets processed in the queue by qmail. Qmail cannot deliver locally and bounces to the forged replyto address." We believe the fix is to patch the qmail-smtpd process to give it the intelligence to check for the existence of local mailboxes BEFORE accepting the message. The problem is when we try to compile the chkuser patch we run into failures due to Plesk Control Panel." Is anyone aware of something we could do differently or better?" Other things that have NOT worked thus far: -Turning off any and all mail processes (to check as an indicator that an individual account has been compromised. This has been verified as NOT the case.) -Turning off mail AND http server processes (in the case of a compromised formmail) -Running EXIM in lieu of Qmail( easy/quick install but xinetd forces exim to close and restarts qmail on its own) -Turned on SPF protection via Plesk GUI. Does not help. -Turned on Greylisting via Plesk GUI. Does not help. -Disabled Bounce notifications via command line That which MIGHT work but have complications: -Use POSTFIX instead of QMAIL (No knowledge of POSTIFX and don't want to bother with it unless anyone knows it has potential to handle backscatter WELL before investing time) -As mentioned above, compiling a chkusr patch, we believe will STOP this problem, along with qmail (because of plesk in the mix, the comile fails every time and Parallels Plesk support is unresponsive unless I cough up MONEY) If I don't clear out the SPAM from the outgoing mail queue nightly, then it clogs up with millions of SPAMs and will bring down the OUTGOING email services. Any and all help welcome and appreciated!

  Read the article

• Centos 5.5 [Read-only file system] issue after rebooting

  - by canu johann

  I have a virtual server under centos 5.5 (hosted by a japanese company called sakura ) Since yesterday, connection through ssh couldn't be established. I've contacted support center who told me to restart VS from the control panel. After restarting, I got the message below Connected to domain wwwxxxxxx.sakura.ne.jp Escape character is ^] [ OK ] Setting hostname localhost.localdomain: [ OK ] Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/vda3 / contains a file system with errors, check forced. /: Inodes that were part of a corrupted orphan linked list found. /: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) @@cat: /proc/self/attr/current: Invalid argument Welcome to CentOS Starting udev: @[ OK ] Setting hostname localhost.localdomain: [ OK ] Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/vda3 / contains a file system with errors, check forced. /: Inodes that were part of a corrupted orphan linked list found. /: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) [FAILED] *** An error occurred during the file system check. *** Dropping you to a shell; the system will reboot *** when you leave the shell. *** Warning -- SELinux is active *** Disabling security enforcement for system recovery. *** Run 'setenforce 1' to reenable. /etc/rc.d/rc.sysinit: line 53: /selinux/enforce: Read-only file system Give root password for maintenance (or type Control-D to continue): bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system (Repair filesystem) 1 # setenforce 1 setenforce: SELinux is disabled (Repair filesystem) 2 # echo 1 (Repair filesystem) 4 # /etc/init.d/sshd status openssh-daemon is stopped (Repair filesystem) 5 # /etc/init.d/sshd start Starting sshd: NET: Registered protocol family 10 lo: Disabled Privacy Extensions touch: cannot touch `/var/lock/subsys/sshd': Read-only file system (Repair filesystem) 6 # sudo /etc/init.d/sshd start sudo: sorry, you must have a tty to run sudo (Repair filesystem) 7 # I have 4 site in production and I need to restart the server quickly (SSH + HTTPD ,...). Thank you for your time.

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubuntu Lucid

  - by MIDoubleKO

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• Outlook refuses to connect to Exchange

  - by wfaulk

  Outlook 2007 under Windows XP connecting to Exchange 2003 SP2: when started, it flips back and forth between "Connecting to Exchange Server" and "Disconnected" three or four times, then gives up and stays disconnected. I tried deleting the ost file (which was nearly 2GB), turning Cached mode on and off, recreating the account inside the Mail control panel, changing the account to use HTTP, and probably some other things. None of it seemed to make any difference, until … After fiddling with it for a while, I got this absurd error message dialog at startup, and it exits after I click OK: Cannot start Microsoft Office Outlook. Cannot open the Outlook window. The set of folders cannot be opened. Microsoft Exchange is not available. Either there are network problems or the Exchange server is down for maintenance. (I'm not sure if I can even trust that message. It's so long, it just feels like a random offset into Outlook's stack of error messages.) Either way, the Exchange server is available to everyone else, and is available via OWA from that computer. I ran Process Explorer against Outlook and it showed 5 or so ESTABLISHED connections to our Exchange server, plus listening on two UDP ports, and two CLOSE_WAIT connections to localhost. If I managed to look at Outlook's IP connections while it was doing its Connecting/Disconnected dance, it had a huge number of connections open to the Exchange server. It more than filled ProcExp's dialog box; I'm guessing at least 20, probably more. The only other odd thing is that our network admin at some point added a wildcard DNS record to the domain name that we use for email, and now Outlook will sometimes (always?) start by complaining about autodiscover.example.com's SSL certificate. There is a web server there, but it doesn't have any sort of email autodiscover anything on it. It doesn't make any difference if I click "OK" or "Cancel" (or whatever the buttons are). I also added a bogus entry for the hostname to Windows' hosts file, pointing it at 127.0.0.2, and it stopped complaining about the certificate. (The CLOSE_WAIT sockets above were from before I made this change, and went away after.) I don't think this is related, as the same problem should exist for everyone, but it might be. This is the second time this user has had this problem. The first time, I never found a solution other than reinstalling Outlook. Now that it's a pattern, I'd like to find a permanent solution, rather than assume it's a random glitch.

  Read the article

• Legacy VB6 application under Win7 SQL error

  - by Shial

  We have a rather unfortunate legacy application at work, written originally in VB6 it predates anybody in our IT department by at least 5 years. We have a contracted developer for ongoing maintenance and where he can he rewrites sections over into .NET code (Not sure about his techniques here, this is a side job for his regular work as an IBM engineer) the application works fine (such as it is) under windows XP. We have only a couple of Windows 7 machines mainly for testing and this application seems to run into a wall. Things like the background not loading and SQL errors. This is even running under administrator. Running an SQL trace from the ODBC control panel shows several interesting things. It makes a connection to the database successfully initially where it runs a query to determine if it is running the correct version. This query works fine. 558-1af0 ENTER SQLExecDirectW HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 BMS 558-1af0 EXIT SQLExecDirectW with return code 1 (SQL_SUCCESS_WITH_INFO) HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 It then seems to drop its connection and can't find the ODBC connection despite the fact its connecting to the same DB. From the trace it looks like it configures the connection then it starts firing off SQLFreeStmt to unbind and close out then when in the application and it tries to do its thing there is no connection. 558-1af0 ENTER SQLFreeStmt HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> BMS 558-1af0 EXIT SQLFreeStmt with return code 0 (SQL_SUCCESS) HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> Then this happens when I try to do something that pulls data 558-1af0 ENTER SQLDriverConnectW HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> BMS 558-1af0 EXIT SQLDriverConnectW with return code -1 (SQL_ERROR) HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> DIAG [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified (0) Nearly all of my searching on this issue comes up with programming issues where the connection string has a problem. The only thing that is different in this particular scenario though is Windows 7, I know the connection string is fine since it works on the XP machines. The VB components are supposed to be still functional under Win7. My computer is running 32 bit win7 and my VP is running Win7 64 bit and both have the same problem so that can be ruled out. I have already tried reinstalling the SQL Native Client and the VB runtime as well as the application in question. Hopefully I can find a solution and not have to resort to using the XP VM.

  Read the article

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Automatic layout of manual network mapping

  - by Paul

  So I have a small business network mainly consisting of two routed layer-2 domains with a total of ca. 100 devices spread over ca. 2000m² production and office spaces. Typical problems to solve using the graph would be: Over what (cable) path is a PC connected to the server? Where to expect devices connected to a switch port? I want to generate a graph of the physical network topology: Nodes are endpoint devices, switch ports, wall outlets, patch panel ports etc. Edges are cable connections. Ideally, grouping edges (or segments) that pass through the same bundle could be grouped. Also I would like to augment the graph data with automatically gathered data (monitoring state, MAC address, Switch port <- MAC entries to build up parts of the map). At the moment I use graphviz for this inside a Confluence wiki like that: layout = "neato" overlap = scale subgraph { rankdir = "TB" subgraph cluster_r1pf1 { r1pf1 [label="{ Rack 1 PF 1 | { <p1>P1 | <p2>P2 | <p3>P3} }", shape=record] } subgraph cluster_switch1 { switch1 [label="{ Rack 1 Switch 1 | { <p1> P1 | <p1> P1 | <p3> P3} }", shape=record] } r1pf1:p1 -> switch1:p1 (obviously there are dozens of entries omitted here) Problem is: I have a hard time to influence graphviz to generate a bearable layout. Edges overlap so bad that you can't read the diagram anymore. The question is: What other tools (be it interactive like Visio, Omnigraffle or I/O-oriented like graphviz) exist that would allow an easily versionable (as in: Operates on a text file) documentation that is both machine and human readable and editable? Why not OmniGraffle or Visio? Well we don't have Macs and Visio is not available at the moment. To buy it I would need good arguments. Automation would be one of that. But last time I looked, versioning Visio files or even thinking about automatic handling was a nightmare. Related: Network Mapping Tools basically asks the same with a focus on generating the complete graph automatically (but without the need to document cabling connections) Recommendations for automatic computer inventory brings up links of "all-in-one" solutions

  Read the article

• Google Apps For Business, SSO, AD FS 2.0 and AD

  - by Dominique dutra

  We are a small company with 22 people in the office. We had a lot of problems with e-mail in the past so I decided to change over to Google Apps for Business. It is the perfect solution for us, except for one thing: I need to be able to control the access to the mailboxes. Only users inside the office, authenticated to AD, or users authenticated to our VPN can connect to gmail. From what I've read it is possible using the SSO (Single Sign On) solution provided by Google - but i am having some trouble finding consistent information about it. First of all, our infrastructure: Windows Server 2008 R2 Active Directory, one domain only. Kerio Control for QoS and VPN. That's about it on our side. On Google Apps' side, I have one account, and 03 domains that my users use to log in. The main domain has most of the users, but the are a couple of people that login using one of the subdomains. I have a 03 domains because I run mail for 03 companies and wanted all to be in within the same control panel. Well, I found some guides on the internet but none of them cover the AD FS installation part. I've read somewhere that I needed to download AD FS 2.0 directly from Microsoft.com, because the one that came with Windows Server was a old version. I downloaded it (adfsSetup.exe) and tried to install but got an error, saying that I needed a Windows Server 2008 Sp2 for that program. My Windows Server 2008 is R2. I really need some help here, this is very importand, I dont want to have to pay $1000 for a SSO solution when i have an AD set up. Can someone please point me out to the right direction? Where can I find an AD FS 2.0 setup compatible with R2 would be a good start, or the one that came with r2 is already the 2.0 version. After the initial setup, there are some guides on the internet about the Google Apps part. It seems to be really easy. I also tried adding AD FS role, but there are a bunch of options wich I have no idea what means, and I coudn't find any guide covering that on the internet. I dont have a lot of experience with Windows Server, but I have a company wich is certificated and provide us with support. I can ask for their help in the later setup, but I dont think ADFS is a very common thing to deal with.

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• Managing multiple independant domains with Google Apps

  - by Saif Bechan

  I am currently running a server where I have multiple domains with all of them running there own mail server. My plan is to outsource this whole email service and have Google, or competitor, do this for me. Let me start by telling you the setup I have now and want to migrate to Google. Initial setup I have a main domain where I run my server, and my nameserver. This is an important domain because this holds the connection with all my internal applications. For example log messages, cronjob messages, and virus-scan messages are sent to this domain. This email is also registered at my registrar and I use it to communicate with my ISP. Next I run a few independent websites that all need their independent email addresses. This can be on shared space, I don't mind. 1 Gig will be enough for everything I am going to do. Summary: superdomain.com (which only has a catchall for internal use and communication with my ISP) cars.com (independent) flowers.com (independent) foods.com (independent) I am going to be the admin for all of this. The independent domains don't need there own admin panel, they just need email addresses like info@ support@, etc. I do all the managing and they just send and receive emails using the accounts i give them. All of the websites have there different staff that use the accounts. Tried so far I have registered my superdomain, but I can only add aliases to the main domain. If I make all the other domains aliases the emails from [email protected] and [email protected] will have the same inbox. I want them to be separate. is the only way to achieve this by creating an account for each domain? And if so, is there no way of creating a superdomain account where I can edit all these accounts easily without having to log in 4 different places to get my work done. I have searched the Google help forums, and posted questions but without any results so far. Questions Can anyone please give me some advice on what to do. I currently use the free program Google has.

  Read the article

• Why Does My Windows 7 PC Freeze After Waking from Sleep?

  - by Blaenk

  Hey guys. I have Windows 7 running on my computer and everything is perfect. There's only one little problem. Sometimes when I leave my computer, I come back and my monitor is turned off or asleep, whichever it is. This is fine, I set it to do this. However, after turning on the monitor and moving the mouse around, the mouse cursor freezes; both the keyboard and mouse don't respond to anything, for example the keyboard's windows key won't bring up the start menu and moving the mouse around does not move the cursor around on the screen. I have to wait about a minute or two before things start working again. I figured this was a power savings setting problem, so I went into Control Panel Power Options. I only have Turn off Display = 30 minutes and Put Computer to Sleep = Never. Of course, I went into the advanced power settings to look through there. I put Never to turn off the hard disk, Sleep after never, and that's about it. Nothing else there looks like it might be causing this. I went into the device manager and checked the mouse and the keyboard, and they both have the Allow this device to wake the computer checked for both of them. Perhaps this other bit of information might help: Sometimes I VNC into my PC using my MacBook, and sometimes, as soon as it shows me the desktop, the same thing happens. The mouse won't move and VNC won't register any events on the server (Which is my PC of course). I close the client (And I know it has nothing to do with the client), then immediately restart it and try to connect. When I click the connect button, it hangs there, as if the PC is not responding. Basically it's like whenever I try to wake the computer from sleep, it does so by showing me the desktop, then it freaks out. Then again, I guess the computer isn't sleeping because the setting is set to 'Sleep after = Never'. I honestly don't know what's going on, would appreciate any insight. Thanks!

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >