Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 18/286 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• How to reset wireless card settings

  - by Nissan911

  Yesterday i was playing around of the wireless settings, and set up a tftp server. Today, i found the wireless icon does not show up on the panel anymore.. monitor and bluetooth are still there... I did: ifconfig -a, and it shows: etho0 link encap:ethernet, and it has: HWaddress inet6 addresss. RXbytes 0 TX bytes: 0, but it does not even have a ip4 address, nor a mask. The other one is: l0 link encap: local loopback inet addr 127.0.0.1. mask 2550 0 0 Can anyone help me how to reset the settings for my wireless connection? Thanks

  Read the article

• Need a few reboots to connect to wireless

  - by Debajyoti Nandi

  I am running xubuntu 12.10 on my msi wind U100 netbook. I have a problem with the wireless connection. Whether the wireless connects automatically to a known wifi hotspot (both at home and starbucks) is temperamental. Sometimes I need to reboot one or more times to get it connected. Otherwise, it tries and keep asking me to enter the password (which is saved and when it works it does, so the problem is not with the password). Every time my computer awakes up from sleep the same problem. I have to do a reboot to connect to wireless. I searched everywhere but found no solution. I would greatly appreciate if someone has any solution. I will gladly share the hardware/software or config info, if asked, but I don't know exactly what to share and where to find them. Thanks you for any help.

  Read the article

• Wireless not functional

  - by Michael Berkenblit

  I am a complete newcomer to Ubuntu. Today I installed Ubuntu 12.04 onto an 3 or 4 year old laptop - an HP DV2221. Install went fine, except that I can't get the wireless card to operate. I see that there are drivers installed (Broadcom STA wireless) and it says they are activated, but the wireless light on the body of the computer is lit as orange, when it should be blue, and if I disconnect the Ethernet wire, there is no ability to get onto Firefox. I've looked at some of the similar questions on this site, as well as Googling the issue - mostly, I guess I don't understand how to navigate or do some of the fixes recommended - I'm fairly adept technologically around Windows, but know zilch about Linux and how to perform some of the fixes - so, if possible, please tell me how I get to the menus needed to rectify the situation.

  Read the article

• If I enable/disable my wireless device, my computer will panic

  - by Yinyanghu

  Now, I use Debian 6.0.6 instead of Fedora 16/17. But I still sustain the problem of my wireless problem. If I enable/disable my laptop wireless device or my usb wifi adaptor, my laptop will panic. It seems like all the processes stop at that time and I have to restart my laptop directly. P.S. I think I installed the drivers correctly and the linux kernel may have some bugs. For example, when I unplug my usb wifi adaptor or I use this command, ifdown wlan0 I encounter this problem. Wireless Device: PCI: 03:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) USB: Bus 002 Device 005: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• Wireless/Bluetooth problems on t43p

  - by user75965

  I have been struggling to get my wireless mini pcmcia card recognised by 12.04. It suddenly stopped, mid session. I have taken it out and replaced with a couple of spares with slightly different serial numbers. One had no joy - 'unauathorised'. The other worked briefly for thunderbird but not firefox, it seemed. The network controller reads like this: 0b:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05) I have ordered a replacement from ebay, and hope I got the right one - used the the FRU number from the one that stopped working. But I have ALWAYS had no joy with my Thinkpad t43p Bluetooth and Ubuntu ( 12.04, and even 11.04 and 11.10, if I remember rightly). Do you think the Bluetooth problem will solve with a new mini pcmcia? Surely not, as it has never worked, whereas Wireless worked until a couple of weeks ago...

  Read the article

• Wireless doesn't connect in Ubuntu 10.04 Lxde

  - by David

  Problem I have a Dell mini 9, and the wireless has worked without trouble in Ubuntu and Xubuntu versions 8.04 and 10.04. However, after installing lxde, the wireless doesnt connect. Network manager recognizes the local networks, and will say that it is connected, but ifconfig does not confirm the connection or the existance of a wlan0. I have another Ubuntu 10.04 notebook that works fine. My wireless device is Broadcom BCM4312 802.11b/g What I have tried I have tried to remove and install network-mananager and inxi but neither work, and sudo modprobe wl returns WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.

  Read the article

• Can't connect to wireless without typing sudo modprobe b43 in terminal

  - by user90889

  I just upgraded to 12.04 on an old ACER Travelmate 5320 using Broadcom 4311. I wasn't able to connect to the internet through the wireless for a few days. It didn't even display wireless networks. I was finally able to make it work by following the instructions found here: http://linuxwireless.org/en/users/Drivers/b43#supported However, each time I log on to the computer I have to go to the terminal and type sudo modprobe b43 to make the wireless work. Is there somehow I can avoid this? I have used Ubuntu for many years but always relied on other people to help me with the technical stuff. The terminal is alien to me so I literally follow online forum instructions without knowing what I'm doing. Also, I tried many many things before I managed to make it work. So I'm worried I may have installed something that now conflicts with whatever the sudo modprobe b43 does. Thank you

  Read the article

• No wireless after resuming from suspend?

  - by lapor

  When I resume my computer from suspend it doesn't want to connect to any wireless connection. It looks like it is connecting, but after a while it asks me to retype a password for wireless connection. It connect after I restart it. I am using Toshiba Satellite A210 and Ubuntu 10.10 (I have the same problem with 10.04 and 11.04 beta2. 14:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) Subsystem: Askey Computer Corp. Device 7128 Flags: bus master, fast devsel, latency 0, IRQ 19 Memory at cfcf0000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath5k Kernel modules: ath5k Should I file a bug?

  Read the article

• Ubuntu 12.04 on Vm Player showing Wired Network Instead of Wireless Network

  - by Fak365

  I am new to Ubuntu, recently I installed ubuntu 12.04 in Vm Player (Virtual Machine) on my Dell laptop having windows 7 ultimate 32 bit for just to check the security of my wireless network and want to crack the WiFi (WPA-PSK) password but in ubuntu it does not show the wireless network it shows the 2 arrow sign as i have not connect the ethernet cable to my laptop and connected through WiFi on my main OS (windows 7) but it shows the wired network and internet is working but it does not show wifi connection. On windows 7 WiFi is connected and showing the WiFi connection and working correctly.But my main motive is to crack the WiFi password as it can't detect WiFi network so what to do? Please Help.!!thanks My Laptop Specification : Laptop : Dell Latitude D620 OS : Windows 7 Ultimate 32 bit Processor : Core Duo 2 T7200 @ 2Ghz Ram : 2 GB WiFi card : Intel Pro/Wireless 3945 ABG Virtual Machine : Vm Player V 5.0.1 If Need to Install Drivers Please Give Me Full Information how to install and which driver I should install. Thanks In Advance.

  Read the article

• wireless not working, but wired does

  - by user211762

  First of all I'm new to Ubuntu, just bought a laptop with Ubuntu yesterday. I disable wireless networking in the upper right corner, and I don't have option to enable it back. I tried a lot of things and none is seems to work: I installed Wicd network manger, and it says no wireless network found, but i assure you there are several of them as my smart tv can detect them. when I type rfkill list, I get this: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no when I type ifconfig wlan0, I get this: wlan0: error fetching interface information: Device not found

  Read the article

• Manually re-enable wireless and bluetooth

  - by tacozmeister

  So, today, I decided to turn off bluetooth to save battery power. When I did so, it did everything like normal. Whatever. But whenever I want to re-enable Wifi and Bluetooth, it just has "Enable Wireless" and "Enable bluetooth" grayed out in the respective things on the top-right of the desktop. I am using 12.04 Precise Pangolin on a Dell laptop that has never had wireless problems before. Clicking the grayed-out part does nothing. Re-logging and restarting has no effect, and I'm on an account that has full administrative permission. My attempts: ~$ sudo dmesg | grep wlan0 [19.960211] ADDRCONF(NETDEV_UP): wlan0: link is not ready . ~$ sudo dmesg | grep blue [[nothing]] What do I do to manually re-enable wireless and bluetooth?

  Read the article

• Recommended ADSL/ADSL2 router that supports PPTP VPN dial-out, 802.11n and gigabit ethernet?

  - by Throlkim

  I'm looking for a new router to provide a VPN tunnel for my home network. My plan is to pass all internet traffic over a PPTP VPN provided by the router, which should ensure that the connection stays alive and only passes traffic over that protocol. I'm normally quite a fan of Draytek routers, and their 2710n does seem to feature VPN dial-out but it lacks Gigabit ports (though I can make do with that if the VPN support is good enough). Has anyone got any suggestions or personal experience in a similar setup? I'm happy to consider anything that supports dd-wrt (as I believe that supports VPN-out, though I may be wrong). Bonus points for models available in the UK.

  Read the article

• No more internet connection after update in 14.04 with Intel Dual Band Wireless AC 7260

  - by luis

  My Dell XPS 15 (haswell) was working fine until I stupidly accepted recently to apply Ubuntu updates. Since then, my wifi does not work (it shows "device not managed" when clicking wifi icon in toolbar). Even USB to Ethernet adapter does not seem to work. Bluetooth at least "sees" other bluetooth devices around... See below output from dmesg (dmesg |grep iwl) : [ 886.462459] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 886.462561] iwlwifi 0000:06:00.0: Direct firmware load failed with error -2 [ 886.462562] iwlwifi 0000:06:00.0: Falling back to user helper [ 886.463284] iwlwifi 0000:06:00.0: loaded firmware version 22.1.7.0 op_mode iwlmvm [ 886.475345] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 886.475433] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.475684] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.689214] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Below the output from modinfo iwlwifi: filename: /lib/modules/3.13.0-29- generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko license: GPL author: Copyright(c) 2003-2013 Intel Corporation <[email protected]> version: in-tree: description: Intel(R) Wireless WiFi driver for Linux firmware: iwlwifi-100-5.ucode firmware: iwlwifi-1000-5.ucode firmware: iwlwifi-135-6.ucode firmware: iwlwifi-105-6.ucode firmware: iwlwifi-2030-6.ucode firmware: iwlwifi-2000-6.ucode firmware: iwlwifi-5150-2.ucode firmware: iwlwifi-5000-5.ucode firmware: iwlwifi-6000g2b-6.ucode firmware: iwlwifi-6000g2a-5.ucode firmware: iwlwifi-6050-5.ucode firmware: iwlwifi-6000-4.ucode firmware: iwlwifi-3160-7.ucode firmware: iwlwifi-7260-7.ucode srcversion: 1E6912E109D5A43B310FB34 alias: pci:v00008086d0000095Asv*sd00005490bc*sc*i* (a pack of lines of kind "alias: pci:xxxxx...." that I guess are not helpful) alias: pci:v00008086d0000095Bsv*sd00005290bc*sc*i* depends: cfg80211 intree: Y vermagic: 3.13.0-29-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: 66:02:CB:36:F1:31:3B:EA:01:C4:BD:A9:65:67:CF:A7:23:C9:70:D8 sig_hashalgo: sha512 parm: swcrypto:using crypto in software (default 0 [hardware]) (int) parm: 11n_disable:disable 11n functionality, bitmap: 1: full, 2: disable agg TX, 4: disable agg RX, 8 enable agg TX (uint) parm: amsdu_size_8K:enable 8K amsdu size (default 0) (int) parm: fw_restart:restart firmware in case of error (default true) (bool) parm: antenna_coupling:specify antenna coupling in dB (defualt: 0 dB) (int) parm: wd_disable:Disable stuck queue watchdog timer 0=system default, 1=disable, 2=enable (default: 0) (int) parm: nvm_file:NVM file name (charp) parm: bt_coex_active:enable wifi/bt co-exist (default: enable) (bool) parm: led_mode:0=system default, 1=On(RF On)/Off(RF Off), 2=blinking, 3=Off (default: 0) (int) parm: power_save:enable WiFi power management (default: disable) (bool) parm: power_level:default power save level (range from 1 - 5, default: 1) (int) I downloaded the latest versions of iwlwifi firmware from git (git clone git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git; copy iwlwifi-3160-9.ucode iwlwifi-7260-9.ucode iwlwifi-7265-9.ucode to /lib/firmware and reboot) but as you can imagine it did not help. Update #1: Downloaded from http://wireless.kernel.org/en/users/Drivers/iwlwifi?action=AttachFile&do=get&target=iwlwifi-7260-ucode-22.15.8.0.tgz and copied the file into /lib/firmware. After reloading it with modprobe, it seems to be OK: [ 14.761283] iwlwifi 0000:06:00.0: enabling device (0000 -> 0002) [ 14.761472] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 14.772478] iwlwifi 0000:06:00.0: loaded firmware version 22.15.8.0 op_mode iwlmvm [ 14.800274] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 14.800349] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 14.800657] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 15.007048] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' However, clicking in wifi in the toolbar still shows "device not managed". Any clues? Many thanks! Luis

  Read the article

• How do I get wireless to work on a Dell Mini 1018 with Realtek RTL 8188CE Network Adapter?

  - by Laurence Nagel

  My Dell Mini 1018 used to work fine with Ubuntu 12.04 with no problems connecting with the wireless card. Then I made the big mistake of attempting to disable WiFi by right-clicking on the wireless applet and un-checking "Enable Wireless." Since then, I cannot get wireless working again. The wireless applet reports that "wireless is disabled by hardware switch" but there is no hardware switch on this computer. Issuing a rfkill list yields the following: 0: dell-wifi: Wireless LAN Soft blocked: yes Hard block: yes 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I'm in way over my head, and my computer is now useless. Help!!!

  Read the article

• Wireless cycling between connected and disconnected

  - by Tony Kilgore

  My friend has a Acer Aspire 5733Z-4851 it keeps disconnecting and connecting to his wifi but his hard wire will run just fine. Any suggestions? All the codes: lspci: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) lsmod: Module Size Used by snd_seq_dummy 12798 0 rfcomm 46619 0 bnep 18140 2 bluetooth 209199 10 rfcomm,bnep parport_pc 32688 0 ppdev 17073 0 lp 17759 0 parport 46345 3 parport_pc,ppdev,lp binfmt_misc 17500 1 ums_realtek 17949 0 snd_hda_codec_realtek 77876 1 uas 17844 0 coretemp 13400 0 snd_hda_intel 33491 4 snd_hda_codec 134212 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 96580 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30512 1 snd_seq_midi uvcvideo 76749 0 videobuf2_core 32851 1 uvcvideo videodev 120309 2 uvcvideo,videobuf2_core videobuf2_vmalloc 12860 1 uvcvideo videobuf2_memops 13368 1 videobuf2_vmalloc snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61521 3 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event snd_timer 29425 2 snd_pcm,snd_seq arc4 12529 2 snd_seq_device 14497 4 snd_seq_dummy,snd_seq_midi,snd_rawmidi,snd_seq psmouse 95552 0 ath9k 131308 0 tg3 148780 0 snd 78734 17 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device microcode 22803 0 mac80211 539908 1 ath9k ath9k_common 14055 1 ath9k ath9k_hw 395218 2 ath9k,ath9k_common ath 23827 3 ath9k,ath9k_common,ath9k_hw i915 520629 3 soundcore 15047 1 snd serio_raw 13215 0 cfg80211 206566 3 ath9k,mac80211,ath snd_page_alloc 18484 2 snd_hda_intel,snd_pcm intel_ips 18049 0 lpc_ich 17061 0 drm_kms_helper 46784 1 i915 drm 275528 4 i915,drm_kms_helper mei 40690 0 i2c_algo_bit 13413 1 i915 joydev 17457 0 acer_wmi 32453 0 sparse_keymap 13890 1 acer_wmi mxm_wmi 12979 0 mac_hid 13205 0 wmi 19070 2 acer_wmi,mxm_wmi video 19335 2 i915,acer_wmi usb_storage 48838 1 ums_realtek sudo lshw -C network: *-network description: Ethernet interface product: NetLink BCM57780 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: b8:70:f4:9a:35:b6 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=half firmware=sb latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:44 memory:d3400000-d340ffff[/QUOTE][QUOTE]*-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 68:a3:c4:eb:60:7d width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-19-generic firmware=N/A ip=192.168.0.168 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d2400000-d240ffff)

  Read the article

• How can a Cisco Aironet wireless card connect to a WPA encrypted network?

  - by Aibara Iduas

  I have a Thinkpad T40 running Ubuntu 10.10. I want to connect to wireless networks with WPA encryption; they appear in the network list, but are grayed out. The card does support WPA, since it works in Windows. In 10.10 the wireless works just fine with unprotected and WEP networks, but cannot connect to any WPA networks. The card is a Cisco Aironet Wireless 802.11b. I've been reading a lot of forum posts trying to find a solution, but either encounter threads where no solution was found or answers longer apply (most date from 2007, since this isn't the newest of computers). Here is the output of sudo lshw -c network: *-network:1 DISABLED description: Wireless Interface product: Cisco Aironet Wireless 802.11b vendor: AIRONET Wireless Communications physical id: 2 bus info: pci@000:02:02.0 logical name: eth1 version: 00 serial: 00:02:8a:78:6a:44 width: 32 bits clock: 33MHz capabilities: pm vpd bus_master cap_list rom ethernet physical wireless logical configuration: broadcast=yes driver=airo latency=64 maxlatency=4 mingnt=4 multicast=yes wireless=IEEE 802.11-DS Thanks, any help would be greatly appreciated!

  Read the article

• why adding router will hide all share folders

  - by user1285419

  I have several computers running winxp installed in my office, they are all connecting to the WAN providing by the building (wall socket) (DHCP, mask 255.255.252.0). I setup a shared folder in my computer so all other computer in the same group could access it. This configuration have been using for long time. Recently, I am trying to setup a router. I have the WAN port of the router go to the wall socket, connect the NIC to the LAN port of the router, setup the router in DHCP mode (192.168.0.100/255.255.255.0 to 192.168.0.110 /255.255.255.0), I turn off all the firewall (windows one and router's builtin one), the NIC has ip set as DHCP. If I ipconfig/all, I see that the NIC was assigned ip 192.168.0.100. I can access the internal, email whatever. However, the shared folder can no longer be accessed by other computers in the same group. I think it is the problem of ip. But what's really weird is if I turn off the DHCP function in the router, ipconfig/all always give 0.0.0.0/255.255.255.255 and I cannot access the internet. I have no idea what's going on. Anyone know how to fix it and allow the shared folder in application of router? Thanks.

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• can connect to wifi router but not the internet 12.10

  - by harsh

  I believe i have tried every trick in the book ! I am able to access my router from my ubuntu desktop but not even a single site on the internet. i have installed the drivers for my pci wifi card following this procedure : http://steveswinsburg.wordpress.com/2011/03/12/how-to-install-a-d-link-dwa-525-wireless-network-card-in-ubuntu-10-04/ Earlier it didn't connect to the internet and kept prompting me for the password. after i installed the driver it got connected ! but now i cant access the internet and can only access my router. i deleted the resolv.conf file. I have also tried the "rkill" command and it shows it is unlocked. I have even tried pinging the ip's 8.8.8.8 & 8.8.4.4 and i get replies from both. I have also added them on my wifi configuration setup on ubuntu desktop. I am new to ubuntu but learning fast :-) These are the things i don't like about ubuntu, the simple tasks are difficult for a person coming from windows. I am using ubuntu 12.10. please reply at the earliest i would be very thankful.

  Read the article

• Wireless on Inspiron 1501 not working on Ubuntu 12.04 LTS

  - by Jeek C

  As titled, I have Ubuntu 12.04 LTS on an Inspiron 1501, and the wireless has refused to work thus far. Below is what I have tried: Activating the Broadcom driver via System Settings Additional Driver Using the below commands sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer installing the cutter software Sadly, none of them can get the wireless working. Is there anything else I can try?

  Read the article

• Can't get Wireless RT2x00usb driver to work, and can't blacklist it

  - by TheLQ

  After a two year hiatus to Linux, I try it again out again. And then I run into to driver issues... I have an old Linksys WUSB54G v4 Wireless USB Adapter. In previous versions I had to use a combination of Ndiswrapper and Wicd to hope of getting it working. In 10.10, apparently there are built in drivers for it. Unfortunately they don't work. Fails to connect to my WPA network, fails to connect to my open unencrypted network. Wicd fails at "Obtaining IP address" or when using static IPs fails at verifying connectivity to network. Getting fed up I tried the ndiswrapper approach. Installed and configured, but still not working, even when blacklisting the rt2570 module. So for some debugging I added some lines to my /etc/modprobe.d/blacklist.conf file blacklist rt2570 blacklist prism54usb blacklist rt2x00lib blacklist rt2x00usb Restart and find this: lordquackstar@quackbeast:/etc/modprobe.d$ lsmod | grep rt2 rt2500usb 18049 0 rt2x00usb 9779 1 rt2500usb rt2x00lib 27275 2 rt2500usb,rt2x00usb led_class 2633 1 rt2x00lib mac80211 231541 2 rt2x00usb,rt2x00lib cfg80211 144470 2 rt2x00lib,mac80211 Seems to be ignored... Tried this: lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00usb ERROR: Removing 'rt2x00usb': Resource temporarily unavailable lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00lib ERROR: Removing 'rt2x00lib': Resource temporarily unavailable and couldn't connect. Restarted and was back to the same modules loading. Maybe there's something in the log: lordquackstar@quackbeast:/etc/modprobe.d$ tail -n100000 /var/log/syslog | grep rt2 Dec 13 19:01:15 quackbeast kernel: [ 23.698056] Registered led device: rt2500usb-phy0::radio Dec 13 19:01:15 quackbeast kernel: [ 23.698140] Registered led device: rt2500usb-phy0::quality Dec 13 19:01:15 quackbeast kernel: [ 23.701680] usbcore: registered new interface driver rt2500usb Dec 13 19:01:15 quackbeast NetworkManager[855]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Dec 13 19:17:47 quackbeast kernel: [ 23.521759] Registered led device: rt2500usb-phy0::radio Dec 13 19:17:47 quackbeast kernel: [ 23.521824] Registered led device: rt2500usb-phy0::quality Dec 13 19:17:47 quackbeast kernel: [ 23.524740] usbcore: registered new interface driver rt2500usb Dec 13 19:17:47 quackbeast NetworkManager[798]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Seems to be autoloading. So this means that even if I pull it out, remove the module, and get it working, it still won't work when its plugged in all the time. More info: lordquackstar@quackbeast:/etc/modprobe.d$ sudo lshw -C Network *SNIP* *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:12:17:9b:f3:1e capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=2.6.35-24-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg USB: lordquackstar@quackbeast:/etc/modprobe.d$ lsusb | grep -i rt Bus 001 Device 003: ID 13b1:000d Linksys WUSB54G v4 802.11g Adapter [Ralink RT2500USB] Any suggestions on how to either fix the rt2x00usb driver or permanently block it from loading? Note that I already have ndiswrapper installed

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >