Search Results

Search found 7124 results on 285 pages for 'printer driver'.

Page 180/285 | < Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >

• Screen Brightness not adjustable for Acer Aspire S3

  - by Kakadu90

  First of all, thank you very much for providing this useful forum. Too bad for me, there is no support for the Acer Aspire S3 yet (just came out in October) Short Description of the Problem: I cannot adjust the screen brightness. Neither Compiz nor the FN Key combination work. Also the fan keeps running on full power. As you can guess, both of these drain my battery. The Setup: Acer Aspire S3, Intel i5 newest Generation, Intel HD3000 Grafic Accelerator (no driver maybe?) Thanks in advance, Kakadu90

  Read the article

• WiFi and Bluetooth will not work on Dell Studio XPS 1645

  - by Ross

  Today I acquired a Dell XPS 1645. Ubuntu seems to run alright on it however The bluetooth is not detected and the WiFi doesn't work. The WiFi is especially weird because I actually have the restricted driver enabled for it. It also worked for a short while when I first booted into Ubuntu however now there isn't even an option to enable wireless. If anyone could possibly help me out with this I'd deeply appreciate it. I've not had to return to Windows for a good while and it's not something I want to have to do now.

  Read the article

• Acer Aspire One 722 broadcom 4313 wifi

  - by Colin Matheson

  I had an Acer Aspire One 722 with the Atheros Wifi card and it worked fine on 11.04. So we bought 200 of them for our school. However these all came with the Broadcom BCM4313 wireless card and there are issues. It is using the brcmsmac driver and they connect initially. However after a time (sometimes just a few webpages) some of them lose connection. However, they still have an IP and network-manager says they are connected, but no pages load and you can't ping anything on the LAN or internet. A disconnect/reconnect can fix it, but sometimes a restart is required. It happens frequently so is a major issue. Lots of broadcom drivers are blacklisted: bcm43xx, b43, brcm80211. Any ideas or experiences with the broadcom4313 card? Please save these computers from a Windows fate!

  Read the article

• How to design a character animation system?

  - by Andrea Benedetti

  I'm searching for suggestions and resources on the possible ways to design a character animation system. I mean a system built on top of the graphics engine (as graphics engine I use Ogre3D, that provide an animation layer), and in strict contact with the logic of the game. It's for a sports title, so the question is not easy. Edit: What I'm searching for are suggestions and resources about the action state mechines (or animation state machines), that is build on top of the animation pipeline already provided by the graphics engine. So, a state-driver animation interface for use by virtually all higher-level game code.

  Read the article

• Why does my touchpad fail on resume from standby?

  - by pst007x

  On resume touchpad disables and a reboot is needed to re-activate. Macbook Pro 6.1 Ubuntu 11.10 MAC 64bit Suspend - ok Suspend Resume - ok However, on resume in the loggin screen my touchpad works, but after I enter my password and return to the desktop the touchpad fails. A usb mouse still works fine. I have to re-boot in order to re-enable toe touchpad. This was not an issue when I had Ubuntu 10.10 32bit installed. The install was a fresh install. The bcm5974 driver will not install, says codependency errors. I manually try to install all dependencies and I get this error: E: hid-dkms: subprocess installed post-installation script returned error exit status 10 E: bcm5974-dkms: dependency problems - leaving unconfigured Thanks

  Read the article

• Q-Tec Webcam 100 (093a:2460) video quality is horrible at best

  - by Sir Emeth

  I just bought a new usb webcam for my desktop setup of Ubuntu Natty Narwhal. I plugged it in, started up Cheese, and saw my smiling face. But it was green and lined, very poor quality overall. I am skeptical that this is due to a poor quality webcam. :P I tried it in Skype, Google+, and Gchat, but all of those showed only a black screen. They recognized the webcam as present, but showed no stream from it. Kamoso showed a black screen as well, and Camorama had even poorer quality than Cheese. Here are the details for the webcam from lsusb: Bus 001 Device 005: ID 093a:2460 Pixart Imaging, Inc. Q-TEC WEBCAM 100 Am I missing a driver, or are there settings somewhere I need to tweak?

  Read the article

• Netgear WNA1100 stopped working

  - by NOLFXceptMe

  I'm facing a rather strange issue with the USB wireless adapter WNA1100. I was able to connect to wireless using this yesterday. However, today am not. lsmod shows ath9k_htc, ath9k_common, ath9k_hw, ath and ndiswrapper. I'm not sure if this is relevant to the above problem, but between yesterday and today, the only change was an upgrade to Ubuntu 2.6.38 kernel, which caused the NVIDIA driver to break (I have a 7300GT), so I had to ignore that kernel, reboot into 2.6.35, and rebuild NVIDIA module from NVIDIA-Installer-270.run. Help?

  Read the article

• How to make "xrandr" work with GMA500?

  - by Nwbie

  Is it error at driver of graphic chip or Xorg or kernel? I am Asus T91mt with GMA500, Ubuntu 12.04.1. I would like too see only a notice of connection at least. A log of xrandr: $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation System Corporation System Controller Hub (SCH Poulcbo) Graphics Controller (rev 07) vp@vc:~$ xrandr --verbose xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 600, current 1024 x 600, maximum 1024 x 600 default connected 1024x600+0+0 (0x138) normal (normal) 0mm x 0mm Identifier: 0x137 Timestamp: 26863 Subpixel: unknown Clones: CRTC: 0 CRTCs: 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: 1024x600 (0x138) 0.0MHz *current h: width 1024 start 0 end 0 total 1024 skew 0 clock 0.0KHz v: height 600 start 0 end 0 total 600 clock 0.0Hz vp@vc:~$ xrandr --prop xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 600, current 1024 x 600, maximum 1024 x 600 default connected 1024x600+0+0 0mm x 0mm 1024x600 0.0* vp@vc:~$ Please help, i am linux newbie and i am tired ;/

  Read the article

• My wireless is hard-blocked

  - by Cristian

  I'm new to linux and i am having trouble getting my wireless to work I've found the following things Wireless LAN Soft blocked: no Hard blocked: yes and : *-network DISABLED description: Wireless interface product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 6c:62:6d:19:38:b9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-25-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:fdfe0000-fdfefff Can you please tell me what to do?

  Read the article

• Chrome and Catalyst - no tab text

  - by Martin Fejes

  I just installed Ubuntu, updated, installed AMD proprietary drivers (for my Radeon HD6870) and noticed that some (most) of the tabs in Google Chrome don't have text, only the favicon. My first idea was that maybe 13.10 may have some issues with the new drivers so I switched to the normal driver instead of the beta one. It was not good. Okay then, I put back the open source drivers. It worked. Okay, it's strange. Let's install Ubuntu Gnome to see if it's Unity. No it was not. Let's install Ubuntu 13.04. Same behavoir. By this time I was desperate. I installed Fedora, the problem was there. Now I'm back to Ubuntu 13.10, but am out of ideas. Could anyone help me, please? P.s.: I can upload a screenshot, if needed.

  Read the article

• Input signal out of range; Change settings to 1600 x 900

  - by Clayton

  I recently installed Ubuntu 12.04 onto my HP Pavilion, in an attempt to make the desktop able to dual-boot Windows 7 and Ubuntu. I managed to get down to the last step, and finished the installation process. After it prompted me to remove what I used to install Ubuntu, I did so, removing my SanDisk 8GB flash drive, and allowed the system to reboot. Like usual, the desktop booted with the HP image, with the options at the bottom(Boot Menu, System Recovery, etc). However, when it should have started up with Ubuntu(like I'm certain it should have done), I received the following error: Input signal out of range Change settings to 1600 x 900 From the time I installed the operating system, back in late August, till now, I've been trying to figure out how I would go about fixing this issue. My mom is also starting to get frustrated with my not having resolved the issue, as its the only desktop that has a printer installed. Is there any possible way to resolve this? To summarize the problem: -Successful boot -Screen brings up error -Screen goes to standby -Nothing else possible until desktop is rebooted, which will initiate the above three steps A few notes: -I did not back up my computer before I installed Ubuntu. I didn't have anything to write to, and basically just forgot to. : -I don't have a Recovery Disk. -I don't have the Windows 7 disk that is supposed to come with the computer. -It has been narrowed down by a friend on Skype that the problem lies with the display, and that the vga= boot command does have something to do with fixing the problem Thank you in advance for resolving this problem. I greatly appreciate it. ^^

  Read the article

• Could not connect to wireless unitl reboot (nl80211)

  - by user107410

  I'm using Samsung NP900X3C. I have problem with occasionally connecting to WIFI, with Ubuntu 12.10. Sometimes my computer could not connect to WIFI "blab", neither after reboot computer. Only solution is to restart WIFI hotspot. It's public WIFI, used by many users, that don't have that problem. My /var/log/syslog: Nov 12 10:09:39 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:39 k15 kernel: [ 8.908610] wlan0: authenticate with 64:70:02:89:7c:d7 Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: scanning -> authenticating Nov 12 10:09:39 k15 kernel: [ 8.915032] wlan0: send auth to 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:09:39 k15 wpa_supplicant[1308]: wlan0: Trying to associate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:39 k15 kernel: [ 8.916753] wlan0: authenticated Nov 12 10:09:39 k15 kernel: [ 8.916839] wlan0: waiting for beacon from 64:70:02:89:7c:d7 Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: authenticating -> associating Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associating -> disconnected Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: disconnected -> scanning Nov 12 10:09:42 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:42 k15 kernel: [ 12.386212] wlan0: authenticate with 64:70:02:89:7c:d7 Nov 12 10:09:42 k15 wpa_supplicant[1308]: wlan0: Trying to associate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:42 k15 kernel: [ 12.389114] wlan0: send auth to 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:09:42 k15 kernel: [ 12.391021] wlan0: authenticated Nov 12 10:09:42 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: scanning -> authenticating Nov 12 10:09:42 k15 kernel: [ 12.391332] wlan0: waiting for beacon from 64:70:02:89:7c:d7 Nov 12 10:09:42 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: authenticating -> associating Nov 12 10:09:43 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associating -> disconnected Nov 12 10:09:43 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: disconnected -> scanning Nov 12 10:09:46 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) and after restart WiFi, I could connect: Nov 12 10:11:51 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: inactive -> scanning Nov 12 10:11:55 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:11:55 k15 kernel: [ 144.445154] wlan0: authenticate with 64:70:02:89:7c:d7 Nov 12 10:11:55 k15 kernel: [ 144.453994] wlan0: send auth to 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:11:55 k15 wpa_supplicant[1308]: wlan0: Trying to associate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: scanning -> authenticating Nov 12 10:11:55 k15 kernel: [ 144.455860] wlan0: authenticated Nov 12 10:11:55 k15 kernel: [ 144.458681] wlan0: associate with 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: authenticating -> associating Nov 12 10:11:55 k15 kernel: [ 144.462799] wlan0: RX AssocResp from 64:70:02:89:7c:d7 (capab=0x431 status=0 aid=9) Nov 12 10:11:55 k15 kernel: [ 144.486368] wlan0: associated Nov 12 10:11:55 k15 wpa_supplicant[1308]: wlan0: Associated with 64:70:02:89:7c:d7 Nov 12 10:11:55 k15 kernel: [ 144.487435] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associating -> associated Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associated -> 4-way handshake This problem is appearing regulary. My WiFi device control is nl80211. Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): using nl80211 for WiFi device control Nov 12 10:09:32 k15 NetworkManager[1004]: <warn> (wlan0): driver supports Access Point (AP) mode Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 3) Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/0 Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): now managed Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): bringing up device.

  Read the article

• Cannot authenticate to SBS 2003

  - by Lerp

  I am trying to connect my machine to my work's entirely windows network and I am having a few issues: Whenever I try to access the server, the authentication dialog just keeps popping back up. I cannot connect to the printers (it says connecting to device failed) I have tried setting up samba, winbind, kerberos, likewise open all to no avail. I have a feeling I am just setting them up wrong. My nautilus shows this when I go to Network Windows Network MASTERMAGNETS I can ping both MASTERMAGNETS.LOCAL and 192.168.0.2 after modifying my /etc/hosts james@jamesmaddison:~$ cat /etc/hosts 127.0.0.1 localhost jamesmaddison 192.168.0.2 MASTERMAGNETS.LOCAL 192.168.0.50 Sharp-Printer # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters I believe that's the correct domain (not sure if that's the correct term) as when I do nslookup MASTERMAGNETS.LOCAL I get the following: james@jamesmaddison:~$ nslookup MASTERMAGNETS.LOCAL Server: 192.168.0.2 Address: 192.168.0.2#53 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.3 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.2 It all worked fine before I reinstalled Ubuntu and now I just cannot get access to the server. All help is appreciated, I need to get this working or I fear I will be forced to develop in a windows environment :(

  Read the article

• Ubuntu 12.10, Wireless not working

  - by Karthik

  My Laptop is Acer 5742G with "Npilfy 802.11 wireless". I have both windows 7 and Ubuntu 12.10 Earlier when I had Ubuntu 12.04, the wireless was working fine, but after installing 12.10 wireless is not working at all, although it is still working in windows. I am not able to see "Wireless Networks" in the Network Manager nor in the Network Settings. This was the output I got for rfkill 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no This is a snapshot of my Additional Drivers settings. As you can see, the required driver for wireless is installed.

  Read the article

• Unable to use TL-WN821N

  - by udiw

  Hi, I got a TP-LINK USB wireless module - TL-WN821N, using Ubuntu 10.4 (same problems were also seen in 10.10). From everything I've read online, the usb should work just fine, since the Atheros ar9170 is built into the kernel. However, when I plug it in, it is detected as a USB device, but there is no wlan associated with it, and basically - nothing happens. Am I doing something wrong? what should I do so that the Atheros driver is associated with this device? btw, on Windows it works fine (with the drivers). Some logs: $ uname -mr 2.6.32-28-generic i686 $ lsb_release -d Description: Ubuntu 10.04.2 LTS $ lsusb ... (trimmed) Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 017: ID 0cf3:7015 Atheros Communications, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub $ lsmod |grep ar9 ar9170usb 51296 0 ath 7611 1 ar9170usb mac80211 205402 3 ar9170usb,iwl3945,iwlcore cfg80211 126528 5 ar9170usb,ath,iwl3945,iwlcore,mac80211 led_class 2864 4 ar9170usb,iwl3945,iwlcore,sdhci

  Read the article

• Ubuntu 10.10 freezes

  - by albert green

  Hi, I have the following configuration: CPU: amd athlon 64bit Motherboard: Phoenix with awardBIOS v6.0 APIC mode = disabled Video card: GeForce 5500 Sound card: soundblaster live 24bit RAM: 1.5GB Partitions: ext3 32GB where I installed Ubuntu. Swap 500MB. 180GB Fat32 unmounted. contains data only. I installed Ubuntu 10.10 and used the "Additional driver" program to get the nVidia proprietary drivers. The system works for sometime and randomly freezes. The mouse and keyboard are not responding and I am not able to do a SSH. The only solution is pressing the power button. I tried Kubuntu 10.10 and 32/64-bits versions as well. There is nothing in the logs to suggest what the reason might be. Any help will be appreciated. Thanks in advance.

  Read the article

• Unity Desktop Displays strange lines

  - by Alex Holsgrove

  Didn't quite know what title to give this problem, but hopefully the screenshot will explain more. I am running a Samsung R60+ laptop on Ubuntu 13.10 with a Radeon X1250 GPU. After I login and the Unity desktop shows, I can see these strange lines at the top of the screen. I presumed it was perhaps a driver issue and found this article to see if I could resolve the issue: https://help.ubuntu.com/community/RadeonDriver I cannot get on with Unity at all (where are all of the menus gone!) so perhaps reverting back to Gnome may be a solution in my case? I'd welcome any ideas please.

  Read the article

• rt73.bin for Ubuntu 12.04 LTS?

  - by fNek

  I have a D-Link USB WLAN stick and want to install Ubuntu 12.04 alternate. The installer asks me to insert an exchangable drive containing 'rt73.bin', the driver. I cannot find any binary downloads, but cannot build the package, because I have no other linux PC. What can I do? //EDIT: The reason why I want to do this during setup is that I want to setup an LTSP server. I only found guides that assume one has Internet connection - but I have not. What can I do?

  Read the article

• Metsys.Bson - the BSON Library

  Earlier this month I detailed the implementation of the bson serialization we used in Norm - the C# MongoDB driver. I've since extracted the serialization/deserialization code and created a standalone project for it - in the hopes that it might prove helpful to someone. If you need an efficient binary protocol to transfer data, look no further. There are two methods you need to be aware of: Serializer.Serialize and Deserializer.Deserialize. User u1 = new User{...}; byte[] bytes = Serializer.Serialize(u1); User...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• No sound after installing a new Graphics Card

  - by Dan

  I've just upgraded my graphics card to an Asus Geforce 210 and now my system has no sound. I've ran Update Manager and the Additional Drivers utility which installed the latest Nvida driver. The graphics card is connected to my TV via a DVI-to-HDMI (DVI at the PC end) cable for the visual connection, and an audio jack from my onboard soundcard for my audio connection. Any ideas on how to resolve this? I ran this command ubuntu-bug audio And it outputted this: You seem to have configured PulseAudio to use the "pci-0000_05_00.1" card, while you want output from "NFORCE - NVidia CK804". I've tired a bit of messing about with the audio settings but can't get anything to work.

  Read the article

• Asus X552VL WI-FI Problem

  - by Mitkobg

  I have a problem with my Wireless on my laptop. When i did rfkill list: 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 4: hci0: Bluetooth Soft blocked: no Hard blocked: no 5: phy1: Wireless LAN Soft blocked: no Hard blocked: yes itko@Mitko:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off mitko@Mitko:~$ lspci -nnk | grep -A2 0280 03:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:2c97] Kernel driver in use: ath9k mitko@Mitko:~$ lsmod | grep -e ath9k -e asus asus_nb_wmi 16990 0 asus_wmi 24191 1 asus_nb_wmi sparse_keymap 13948 1 asus_wmi ath9k 164164 0 ath9k_common 13551 1 ath9k ath9k_hw 453856 2 ath9k_common,ath9k ath 28698 3 ath9k_common,ath9k,ath9k_hw mac80211 626557 1 ath9k cfg80211 484040 4 wl,ath,ath9k,mac80211 wmi 19177 3 mxm_wmi,nouveau,asus_wmi video 19476 3 i915,nouveau,asus_wmi

  Read the article

• ralink rt2860 not working anymore in ubuntu 12.10

  - by greenit

  I just upgraded from Ubuntu 12.04 to 12.10, however, my network card is not working anymore... When i had 12.04 installed, i just had to download the driver from Ralink, go to the directory and enter these commands: $ make $ sudo make install and the network card worked... now, when I want to do this in ubuntu 12.10, it seems like it works, but it doesn't. I can enable the module, it recognizes the network card, but i am unable to connect to any wireless network... How can i get my wireless card working again? If any1 knows a solution, please tell it to me, thx in advance

  Read the article

• How do I start xterm with a headless system?

  - by NeViXa

  I'm running Ubuntu 12.04 and I want to boot directly and headless in the terminal (no GUI). After that I want to startx to start a program in xterm. When I boot 'headed', everything is working like supposed to, but: - When I boot headless, startx is not working (no screens found) I already tried to change xorg.conf to below, but it didn't not work: Section "Device" Identifier "VNC Device" Driver "vesa" EndSection Section "Screen" Identifier "VNC Screen" Device "VNC Device" Monitor "VNC Monitor" SubSection "Display" Modes "1280x1024" EndSubSection EndSection Section "Monitor" Identifier "VNC Monitor" HorizSync 30-70 VertRefresh 50-75 EndSection How can I boot headless and still be able to run startx? ANSWER: Adding the BusID to the Devices section in the xorg.conf above, fixed the problem for me. BusID "PCI:1:00:1"

  Read the article

• JavaOne - Java SE Embedded Booth - Pactron Java Programmable Automation Controller (JPAC)

  - by David Clack

  Hi All, So at the last JavaOne we talked about developing a Java powered Programmable Automation Controller (JPAC) with our partner Pactron in Santa Clara. We actually demoed it running first at the Embedded Show in Germany this March. JPAC is based on a Marvell 88F6282 Kirkwood ARM SOC, we partnered with Hilsher from just outside Frankfurt, Germany for the mini pci ProfiBus controllers, Revolution Robotics from Corvallis, Oregon wrote the Java SE Embedded for ARM to Hilscher Linux driver interface. Revolution Robotics also designed the HTML5 application that runs on a Marvell ARM tablet to actually send and receive commands via ProfiBus to a slave device. We will have the system running in our booth at JavaOne this year, come take a look. If you are registered at JavaOne you can come over to the Java Embedded @ JavaOne for $100 Come see us in booth 5605 See you there Dave

  Read the article

• vgaswitcheroo isn't working in Ubuntu 12.04

  - by Forbidden404

  I always used vgaswitcheroo to turn off my discrete graphic, I did a script to turn off in boot, but now, vgaswitcheroo isn't working anymore, I don't know why... look forbidden404@forbidden404-Inspiron-N5110:~$ ls -l /sys/kernel/debug/vgaswitcheroo/switch ls: cannot access /sys/kernel/debug/vgaswitcheroo/switch: Permission denied forbidden404@forbidden404-Inspiron-N5110:~$ grep -i switcheroo /boot/config-* /boot/config-3.2.0-20-generic:CONFIG_VGA_SWITCHEROO=y /boot/config-3.2.0-23-generic:CONFIG_VGA_SWITCHEROO=y /boot/config-3.2.0-24-generic:CONFIG_VGA_SWITCHEROO=y forbidden404@forbidden404-Inspiron-N5110:~$ sudo su [sudo] password for forbidden404: root@forbidden404-Inspiron-N5110:/home/forbidden404# echo OFF > /sys/kernel/debug/vgaswitcheroo/switch bash: /sys/kernel/debug/vgaswitcheroo/switch: No such file or directory root@forbidden404-Inspiron-N5110:/home/forbidden404# ls -l /sys/kernel/debug/vgaswitcheroo/switch ls: cannot access /sys/kernel/debug/vgaswitcheroo/switch: No such file or directory And I'm not using any proprietary driver, k?

  Read the article

< Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >