Search Results

Search found 16096 results on 644 pages for 'top'.

Page 181/644 | < Previous Page | 177 178 179 180 181 182 183 184 185 186 187 188  | Next Page >

  • High load average, low CPU and IO (Centos 5.7)

    - by Ben
    A Drupal 7 site with CiviCRM, after running smoothly for a year on a 1&1 VPS suddenly became unresponsive. Now pages eventually load, but can take more than a minute. Looking at resource use in Virtuozzo, the load average carries a warning, and has remained above 1. While I understand this isn't particularly high, this is a change from when the site was working. Here is a typical snapshot of top: top - 03:10:32 up 3:21, 1 user, load average: 1.16, 1.22, 1.30 Tasks: 43 total, 1 running, 42 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.1%sy, 0.1%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2097152k total, 1015112k used, 1082040k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached CPU idle level never seems to go much below 70%. wa is virtually always at 0. There appears to be lots of free memory. And here is some vmstat output, again showign wa at 0, plenty of free memory, and an idle CPU: procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 0 0 1100872 0 0 0 0 2783 23672 0 538 1 0 99 0 0 1 0 0 1100872 0 0 0 0 0 16 0 101754 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 17 0 103133 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 1 0 102080 0 0 100 0 0 1 0 0 1100872 0 0 0 0 0 6 0 99881 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 1 0 105187 0 0 100 0 0 I've spoken to 1&1 but they don't have any ideas as to what could be causing the high load average. Instead they suggested an upgrade :) I've looked for processes that might be causing this, examined MySQL showprocesslist, and restarted the container with no result. Does anyone have more troubleshooting suggestions or insights?

    Read the article

  • Ballooning Mac OS X kernel_task and Wired memory usage. How to diagnose / fix?

    - by user28930
    I have a very strange issue, which I'm having a hard time diagnosing as to the root cause. I have a Mac Pro (2008, 8-core 2.8 GHz, 8800GT) with 14 GB of RAM (recently upgraded because of this issue!). When I boot my system and log in, vm_stat / top / Activity Monitor will show that kernel_task has about 150 MB allocated, and the machine has about 800 MB of Wired memory being allocated. Even initially, 800 MB seems an awful lot of wired memory to be allocated with no applications running - but, it gets worse. (NB: Wired is locked, unswappable memory) After a very short time, sometimes triggered by something as simple as launching a terminal, kernel_task will balloon to 8-900 MB of Real Mem (RSIZE), and Wired Memory will accelerate to 1.6 GB (implying that all the extra memory requests are for wired RAM in the kernel). If I quit everything (I.E: no running applications, bar an activity monitor or terminal to view top), there is no appreciable reduction in either kernel_task RSIZE, or Wired Memory usage. Going the opposite way, and loading the system with tasks also shows that wired memory does not get reduced - and that importantly it is not reduced in preference to heavy swapping. If I log out and log back in again, it reduces a bit (450 MB kernel_task, 1.28 GB Wired), but not back to the start. I'm not running any wacky kexts - and futhermore, kextstat shows no huge memory allocations there; the largest being com.apple.nvidia.nv50hal at about 4 MB of Memory. The machine feels overall more sluggish when this has happened - unsurprisingly because such a huge amount of RAM has been marked as non-pageable. So I have a few questions: 1) Is there a good way to diagnose what has allocated all of this wired memory? It's often over 2 times the kernel_task size, running no applications. The real memory total doesn't seem to add up - it seems that there is a bunch of RAM that isn't being accounted for anywhere. 2) What is happening to cause the kernel to suddenly require 6 times as much memory?

    Read the article

  • Rack layout for future growth

    - by bleything
    We're getting ready to move to a new colo facility and I'm designing the rack layout. While we have a full rack, we only have 12U worth of hardware right now: 1x 1U switch 7x 1U servers 1x 2U server 1x 2U disk shelf The colo facility requires us to front-mount the switch and use a 1U brush strip, so we'll be using a total of 13U of space. Regarding growth, I'm reasonably sure we'll be adding another 4U in servers, 1-2U of network gear, and 2-4U of storage in the mid-term. Specific questions I'm hoping to get help with: where should I mount the switch? the LEDs are on top... should I group the servers by function with space for adding new machines? as an alternative, should I group servers based on whether they are production or staging? where in the rack should I start? in the middle? at the top? at the bottom? equally spaced? Here's a silly little ASCII diagram of what I'm thinking right now. Please feel free to tear my design apart, I've really no idea what I'm doing :) Any advice is very welcome. edit: to be clear, the colo is providing redundant power with UPS and generator, so that's why there's no power gear in the plan, except for the 0U PDU that I didn't diagram. 42 | -- switch ---------------------- 41 | -- brush strip ----------------- 40 | ~~ reserved for second switch ~~ 39 | ~~ reserved for firewall ~~~~~~~ 38 | 37 | -- admin01 --------------------- 36 | 35 | -- vm01 ------------------------ 34 | -- vm02 ------------------------ 33 | ~~ reserved for vm03 ~~~~~~~~~~~ 32 | ~~ reserved for vm04 ~~~~~~~~~~~ 31 | ~~ reserved for vm05 ~~~~~~~~~~~ 30 | 29 | -- web01 ----------------------- 28 | -- web02 ----------------------- 27 | ~~ reserved for web03 ~~~~~~~~~~ 26 | ~~ reserved for web04 ~~~~~~~~~~ 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | -- db01 ------------------------ 15 | +- disks ----------------------+ 14 | +------------------------------+ 13 | ~~ reserved for more ~~~~~~~~~~~ 12 | ~~ db01 disks ~~~~~~~~~~~~~~~~~~ 11 | 10 | +- db02 -----------------------+ 9 | +------------------------------+ 8 | ~~ reserved for db02 ~~~~~~~~~~~ 7 | ~~ disks ~~~~~~~~~~~~~~~~~~~~~~~ 6 | ~~ reserved for more ~~~~~~~~~~~ 5 | ~~ db02 disks ~~~~~~~~~~~~~~~~~~ 4 | 3 | 2 | 1 |

    Read the article

  • How to wire 20 computers and 20 phones and 1 server into LAN?

    - by John Smith
    I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

    Read the article

  • saslauthd using too much memory

    - by Brian Armstrong
    Woke up today to see my site slow/unresponsive. Pulled up top and it looks like a ton of saslauthd processes have spun up using about 64m of RAM each, causing the machine to enter swap space. I've never seen this many used on there. top - 16:54:13 up 85 days, 11:48, 1 user, load average: 0.32, 0.50, 0.38 Tasks: 143 total, 1 running, 142 sleeping, 0 stopped, 0 zombie Cpu(s): 0.7%us, 0.3%sy, 0.0%ni, 97.3%id, 0.2%wa, 0.0%hi, 0.0%si, 1.4%st Mem: 1048796k total, 1025904k used, 22892k free, 14032k buffers Swap: 2097144k total, 332460k used, 1764684k free, 194348k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 848 admin 20 0 263m 115m 4840 S 0 11.3 5:02.91 ruby 906 admin 20 0 265m 113m 4828 S 0 11.1 5:37.24 ruby 30484 admin 20 0 248m 91m 4256 S 6 9.0 219:02.30 delayed_job 4075 root 20 0 160m 65m 952 S 0 6.4 0:24.22 saslauthd 4080 root 20 0 162m 64m 936 S 0 6.3 0:24.48 saslauthd 4079 root 20 0 162m 64m 936 S 0 6.3 0:24.70 saslauthd 4078 root 20 0 164m 63m 936 S 0 6.2 0:24.66 saslauthd 4077 root 20 0 163m 62m 936 S 0 6.1 0:24.66 saslauthd 3718 mysql 20 0 312m 52m 3588 S 1 5.1 3499:40 mysqld 699 root 20 0 72744 7640 2164 S 0 0.7 0:00.50 ruby 15701 postfix 20 0 106m 5712 4164 S 1 0.5 0:00.50 smtpd 15702 postfix 20 0 52444 3252 2452 S 1 0.3 0:00.06 cleanup 4062 postfix 20 0 41884 3104 1788 S 0 0.3 125:26.01 qmgr 15683 root 20 0 51504 2780 2180 S 0 0.3 0:00.04 sshd 14595 postfix 20 0 52308 2548 2304 S 1 0.2 0:24.60 proxymap 15483 postfix 20 0 43380 2544 1992 S 0 0.2 0:00.38 smtp 15486 postfix 20 0 43380 2544 1992 S 0 0.2 0:00.36 smtp 15488 postfix 20 0 43380 2540 1992 S 0 0.2 0:00.38 smtp 15485 postfix 20 0 43380 2532 1984 S 0 0.2 0:00.36 smtp 15489 postfix 20 0 43380 2532 1984 S 0 0.2 0:00.40 smtp Wasn't sure what Saslauthd is, Google says it handles plantext authentication. The machine has been sending a lot of email through postfix, so this could be related. Anyone know why so many may have spun up? Are they safe to kill? Thanks!

    Read the article

  • 1GB cached memory - Do I need more RAM?

    - by Martin
    The server runs well but I wonder if I should get more RAM. I only have a few MB of "free" memory and 1.2GB of "cached" memory: free: total used free shared buffers cached Mem: 3945 3893 51 0 28 1216 -/+ buffers/cache: 2648 1296 Swap: 3895 857 3038 I learned that cached memory is used while it's free and not. Is the cached value an indicator for the need of more RAM? cat /proc/meminfo 1 day after flushing the cache: MemTotal: 4040048 kB MemFree: 32844 kB Buffers: 18956 kB Cached: 1249092 kB SwapCached: 161576 kB Active: 3611328 kB Inactive: 189104 kB SwapTotal: 3989496 kB SwapFree: 2894200 kB Dirty: 20520 kB Writeback: 0 kB AnonPages: 2523496 kB Mapped: 217744 kB Slab: 70940 kB SReclaimable: 36756 kB SUnreclaim: 34184 kB PageTables: 99648 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 6009520 kB Committed_AS: 6401716 kB VmallocTotal: 34359738367 kB VmallocUsed: 18852 kB VmallocChunk: 34359719439 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB top: top - 17:20:10 up 112 days, 3:06, 1 user, load average: 1.01, 1.62, 1.48 Tasks: 208 total, 1 running, 207 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.6%sy, 0.0%ni, 97.5%id, 1.3%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 4040048k total, 3953108k used, 86940k free, 16348k buffers Swap: 3989496k total, 1095712k used, 2893784k free, 1235436k cached

    Read the article

  • Nginx + uWSGI + Django performance stuck on 100rq/s

    - by dancio
    I have configured Nginx with uWSGI and Django on CentOS 6 x64 (3.06GHz i3 540, 4GB), which should easily handle 2500 rq/s but when I run ab test ( ab -n 1000 -c 100 ) performance stops at 92 - 100 rq/s. Nginx: user nginx; worker_processes 2; events { worker_connections 2048; use epoll; } uWSGI: Emperor /usr/sbin/uwsgi --master --no-orphans --pythonpath /var/python --emperor /var/python/*/uwsgi.ini [uwsgi] socket = 127.0.0.2:3031 master = true processes = 5 env = DJANGO_SETTINGS_MODULE=x.settings env = HTTPS=on module = django.core.handlers.wsgi:WSGIHandler() disable-logging = true catch-exceptions = false post-buffering = 8192 harakiri = 30 harakiri-verbose = true vacuum = true listen = 500 optimize = 2 sysclt changes: # Increase TCP max buffer size setable using setsockopt() net.ipv4.tcp_rmem = 4096 87380 8388608 net.ipv4.tcp_wmem = 4096 87380 8388608 net.core.rmem_max = 8388608 net.core.wmem_max = 8388608 net.core.netdev_max_backlog = 5000 net.ipv4.tcp_max_syn_backlog = 5000 net.ipv4.tcp_window_scaling = 1 net.core.somaxconn = 2048 # Avoid a smurf attack net.ipv4.icmp_echo_ignore_broadcasts = 1 # Optimization for port usefor LBs # Increase system file descriptor limit fs.file-max = 65535 I did sysctl -p to enable changes. Idle server info: top - 13:34:58 up 102 days, 18:35, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 118 total, 1 running, 117 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3983068k total, 2125088k used, 1857980k free, 262528k buffers Swap: 2104504k total, 0k used, 2104504k free, 606996k cached free -m total used free shared buffers cached Mem: 3889 2075 1814 0 256 592 -/+ buffers/cache: 1226 2663 Swap: 2055 0 2055 **During the test:** top - 13:45:21 up 102 days, 18:46, 1 user, load average: 3.73, 1.51, 0.58 Tasks: 122 total, 8 running, 114 sleeping, 0 stopped, 0 zombie Cpu(s): 93.5%us, 5.2%sy, 0.0%ni, 0.2%id, 0.0%wa, 0.1%hi, 1.1%si, 0.0%st Mem: 3983068k total, 2127564k used, 1855504k free, 262580k buffers Swap: 2104504k total, 0k used, 2104504k free, 608760k cached free -m total used free shared buffers cached Mem: 3889 2125 1763 0 256 595 -/+ buffers/cache: 1274 2615 Swap: 2055 0 2055 iotop 30141 be/4 nginx 0.00 B/s 7.78 K/s 0.00 % 0.00 % nginx: wo~er process Where is the bottleneck ? Or what am I doing wrong ?

    Read the article

  • OS X random, jumpy dragging behavior

    - by Chris
    This problem has been going on since I got 10.7, and is persisting or even getting worse since I updated to Mavricks. The best way to describe it is thru an example- Let's say I'm working in Safari. Everything is working fine. Then, I'll switch to another app by clicking on it's window, for example, I'll click on Messages to shoot back a reply. When I click back to Safari, keyboard and mouse inputs don't work! The only way I can regain control of the app (Safari) is by clicking on the apps top bar, which then causes the app to jump left or right. If I'm in Messages and I switch back to Safari by clicking said top bar, it works fine. Same with switching back and forth using command-tab. I've narrowed the problem down to this - the first app (Safari, in this example) is, for some reason, deciding that I'm in the process of dragging the window around. This could be just an oddly persistent glitch in my system, but has anyone else seen this before? Perhaps a misplaced default write... somewhere along the line? Update A PRAM reset did absolutely nothing

    Read the article

  • Resource Monitor (resmon) in Windows Server 2008 R2

    - by Clever Human
    In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

    Read the article

  • fatal error 'stdio.h' Python 2.7 on Mc OS X 10.7.5 [closed]

    - by DjangoRocks
    I have this weird issue on my Mac OS X 10.7.5 /Library/Frameworks/Python.framework/Versions/2.7/include/python2.7/Python.h:33:10: fatal error: 'stdio.h' file not found What caused the above error? This error has been bugging me and i can't install mysql-python as i'm stuck with this step. I'm using Python 2.7.3. Things like Google App Engine ( python ), python script, tornado generally works on my mac. But not mysql-python. I've install MySQL using the dmg image and have copied the mysql folder to /usr/local/ How do i fix this? ======UPDATE====== I've ran the command, and tried to install mysql-python by running sudo python setup.py install. But received the following: running install running bdist_egg running egg_info writing MySQL_python.egg-info/PKG-INFO writing top-level names to MySQL_python.egg-info/top_level.txt writing dependency_links to MySQL_python.egg-info/dependency_links.txt writing MySQL_python.egg-info/PKG-INFO writing top-level names to MySQL_python.egg-info/top_level.txt writing dependency_links to MySQL_python.egg-info/dependency_links.txt reading manifest file 'MySQL_python.egg-info/SOURCES.txt' reading manifest template 'MANIFEST.in' writing manifest file 'MySQL_python.egg-info/SOURCES.txt' installing library code to build/bdist.macosx-10.6-intel/egg running install_lib running build_py copying MySQLdb/release.py -> build/lib.macosx-10.6-intel-2.7/MySQLdb running build_ext gcc-4.2 not found, using clang instead building '_mysql' extension clang -fno-strict-aliasing -fno-common -dynamic -g -O2 -DNDEBUG -g -O3 -Dversion_info=(1,2,4,'rc',5) -D__version__=1.2.4c1 -I/usr/local/mysql/include -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c _mysql.c -o build/temp.macosx-10.6-intel-2.7/_mysql.o -Os -g -fno-common -fno-strict-aliasing -arch x86_64 In file included from _mysql.c:29: /Library/Frameworks/Python.framework/Versions/2.7/include/python2.7/Python.h:33:10: fatal error: 'stdio.h' file not found #include <stdio.h> ^ 1 error generated. error: command 'clang' failed with exit status 1 What other possible ways can i fix it? thanks! Best Regards.

    Read the article

  • LDAP Authentication woes

    - by Marcelo de Moraes Serpa
    Hello list, I have a local OpenLDAP server with a couple of users. I'm using it for development purposes, here's the ldif: #Top level - the organization dn: dc=site, dc=com dc: site description: My Organization objectClass: dcObject objectClass: organization o: Organization #Top level - manager dn: cn=Manager, dc=site, dc=com objectClass: organizationalRole cn: Manager #Second level - organizational units dn: ou=people, dc=site, dc=com ou: people description: All people in the organization objectClass: organizationalunit dn: ou=groups, dc=site, dc=com ou: groups description: All groups in the organization objectClass: organizationalunit #Third level - people dn: uid=celoserpa, ou=people, dc=site, dc=com objectclass: pilotPerson objectclass: uidObject uid: celoserpa cn: Marcelo de Moraes Serpa sn: de Moraes Serpa userPassword: secret_12345 mail: [email protected] So far, so good. I can bind with "cn=Manager,dc=site,dc=com" and the 12345678 password (the local server password, setup on slapd.conf). However, I would like to bind with any user in under the people OU. In this case, I'd like to bind with: dn: uid=celoserpa, ou=people, dc=site, dc=com userPassword: secret_12345 But I'm getting a "(49) - Invalid Credentials" error everytime. I have tried through CLI tools (such as ldapadd, ldapwhoami, etc) and also ruby/ldap. The bind with these credentials fails with a invalid credentials error. I thought that it could be an ACL issue, however, the ACLs on slapd.conf seem to be right: access to attrs=userPassword by self write by dn.sub="ou=people,dc=site,dc=com" read by anonymous auth access to * by * read I was suspecting that maybe OpenLDAP doesn't compare against userPassword? Or maybe some ACL configuration I am missing that is somehow affecting the read access to userPassword for the specific DN. I'm really lost here, any suggestion appreciated! Cheers, Marcelo.

    Read the article

  • Running DNS locally for home network

    - by Roy Rico
    I have a small home network that just got larger ( New roommate, My existing roommate got a laptop (on top of her computer)j, my friends coming over with laptop, etc ). I'd like to run a local DNS server for lookups of my local network stuff (fileserver.local, windowsTV.local, machineA.local, machineB.local, appletv.local). I used to have a business line with a static IP, and run bind/named internally. However, now, I have a normal account. My ISP's DNS servers are constantly changing (for whatever reasons my ISP doesn't like to keep the same IP range for long). I need my local DNS to be automatically updated to use my ISP's DNS for external traffic, but be able to maintain an internal DNS server (getting to update the hosts file is being a hassle with every new machine on top of rebuilding existing machines with win7 or Ubuntu 9.04). Additionally, My ISP's DNS servers often crash or become unresponsive. Are there any open DNS servers that are reliable (i don't want to reconfig every day) that I could use as my primary, then if those fail, then use my ISP's? UPDATE: Also looking for each workstation to be able to use dhcp to connect, but instead of getting ISP dns servers, getting my internal one.... Thanks

    Read the article

  • Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

    - by varesa
    I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

    Read the article

  • Listing group members using ldapsearch

    - by colemanm
    Our corporate LDAP directory is housed on a Snow Leopard Server Open Directory setup. I'm trying to use the ldapsearch tool to export an .ldif file to import into another external LDAP server to authenticate with externally; basically trying to be able to use the same credentials internally and externally. I've got ldapsearch working and giving me the contents and attributes of everything in the "Users" OU, and even filtering down to only the attributes I need: ldapsearch -xLLL -H ldap://server.domain.net / -b "cn=users,dc=server,dc=domain,dc=net" objectClass / uid uidNumber cn userPassword > directorycontents.ldif That gives me a list of users and properties that I can import to my remote OpenLDAP server. dn: uid=username1,cn=users,dc=server,dc=domain,dc=net objectClass: inetOrgPerson objectClass: posixAccount objectClass: organizationalPerson uidNumber: 1000 uid: username1 userPassword:: (hashedpassword) cn: username1 However, when I try the same query on an OD "group" instead of a "container," the results are something like this: dn: cn=groupname,cn=groups,dc=server,dc=domain,dc=net objectClass: posixGroup objectClass: apple-group objectClass: extensibleObject objectClass: top gidNumber: 1032 cn: groupname memberUid: username1 memberUid: username2 memberUid: username3 What I really want is a list of users from the top example filtered based on their group memberships, but it looks like membership is set from the Group side, rather than the user account side. There must be a way to filter this down and only export what I need, right?

    Read the article

  • Openldap with ppolicy

    - by nitins
    We have working installation of OpenLDAP version 2.4 which is using shadowAccount attributes. I want to enable ppolicy overlays. I have gone through the steps provided at OpenLDAP and ppolicy howto. I have made the changes to slapd.conf and imported the password policy. On restart OpenLDAP is working fine and I can see the password policy when I do a ldapsearch. The user object looks like given below. # extended LDIF # # LDAPv3 # base <dc=xxxxx,dc=in> with scope subtree # filter: uid=testuser # requesting: ALL # # testuser, People, xxxxxx.in dn: uid=testuser,ou=People,dc=xxxxx,dc=in uid: testuser cn: testuser objectClass: account objectClass: posixAccount objectClass: top objectClass: shadowAccount shadowMax: 90 shadowWarning: 7 loginShell: /bin/bash uidNumber: 569 gidNumber: 1005 homeDirectory: /data/testuser userPassword:: xxxxxxxxxxxxx shadowLastChange: 15079 The password policy is given below. # default, policies, xxxxxx.in dn: cn=default,ou=policies,dc=xxxxxx,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE I do not what should be done after this. How can the shadowAccount attributes be replaced with the password policy.

    Read the article

  • How to copy a bunch of pages? Is there a 3rd party tool?

    - by unknown (yahoo)
    (I asked the following question at the DNN forum, and also at snowcovered. Nobody knew of such an obvious time-saver being for sale. I'm posting here in case anybody knows of a freeware module that might do this.) By "groups of dnn pages", I mean pages that form a hierarchy (not necessary a hierarchy that is headed with a page at the same level as the Home page.) I know that I can copy web pages, one by one, using the admin login via the web-based dnn interface. But, I'd prefer a script or wizard, of some sort (that runs scripts behind the scenes) that can allow me to 1) specify a web page that I want to copy (along with the hierarchy of pages under it) 2) specify the names and titles of the new top-level pages 3) specify whether the contained modules of the top-level page that I want to copy is to be : ( ) New ( ) Copy ( ) Reference (as in the web-based interface) 4) repeat 3) for each of the source pages in the hierarchy that I want to copy You might say that I am looking to do something similar to creating a portal web site based on a template, except that it's not an entirely new website - instead it's a section of the current web site. I might want to do this because I have an organization which is broken into chapters, and I want each chapter to have, say, it's own General Information page (which acts like it's home page), and underneath that, in it's hierarchy, a Contact Info page and an Events page. so: Home Page   General Information Page     Contact Info     Events -- Home Page   General Information Page     Contact Info     Events   General Information Page Kiwanis - Bloomfield     Contact Info     Events   General Information Page Kiwanis - Dayton     Contact Info     Events If I have 200 chapters, I certainly don't want to copy those 3 web pages using the web based interface, as that would take a long time. (And imagine if each chapter's new sub-website had 30 pages!) I just want to specify the parameters of a copy process, then press a button, and let the system do the rest.

    Read the article

  • Css absolute position don't work in MS WORD

    - by Tim
    Hello! This is a sample: <html> <head> <title>word test</title> </head> <body> <div style='position: absolute; width: 30px; height: 50px; top: 100px; left: 20px; border-color: black; border-width: 1px; border-style: solid;'> <p>Hello!</p> </div> </body> </html> Save it as "word.doc" and open in MS WORD. Absolute position don't work! Div is rendered on the top of document and with 100% width. Why? I can't use a html tables. Version on ms word: 2003

    Read the article

  • Listing group members using ldapsearch

    - by colemanm
    Our corporate LDAP directory is housed on a Snow Leopard Server Open Directory setup. I'm trying to use the ldapsearch tool to export an .ldif file to import into another external LDAP server to authenticate with externally; basically trying to be able to use the same credentials internally and externally. I've got ldapsearch working and giving me the contents and attributes of everything in the "Users" OU, and even filtering down to only the attributes I need: ldapsearch -xLLL -H ldap://server.domain.net / -b "cn=users,dc=server,dc=domain,dc=net" objectClass / uid uidNumber cn userPassword > directorycontents.ldif That gives me a list of users and properties that I can import to my remote OpenLDAP server. dn: uid=username1,cn=users,dc=server,dc=domain,dc=net objectClass: inetOrgPerson objectClass: posixAccount objectClass: organizationalPerson uidNumber: 1000 uid: username1 userPassword:: (hashedpassword) cn: username1 However, when I try the same query on an OD "group" instead of a "container," the results are something like this: dn: cn=groupname,cn=groups,dc=server,dc=domain,dc=net objectClass: posixGroup objectClass: apple-group objectClass: extensibleObject objectClass: top gidNumber: 1032 cn: groupname memberUid: username1 memberUid: username2 memberUid: username3 What I really want is a list of users from the top example filtered based on their group memberships, but it looks like membership is set from the Group side, rather than the user account side. There must be a way to filter this down and only export what I need, right?

    Read the article

  • Ubuntu root privs installation issue

    - by Pam
    I am a fairly new Ubuntu user (and Linux user, for that matter) and I just downloaded a program whose installer was a .sh file. Not thinking, I copied the installer to an /opt subdirectory, thinking that I was going to install the application there: sudo cp ~/Downloads/fooInstaller.sh /opt/someDir I can't remember, but I either had to use sudo because /opt required it, or I just used it without thinking, but in any case, I prefixed with sudo. Once in /opt/someDir, I executed the installer again, using sudo: sudo sh fooInstaller.sh The terminal went crazy, and a few seconds later, a graphical install wizard popped up that guided me through the rest of the process. At the end of the wizard I was prompted to launch the program, and I did, and everything was great. Until... I closed the program, and attempted to add it to my Ubuntu "panel" (the icon panel at the top of the screen). The program was installed to /usr/local/foo/theProgram, and so I specified that URL as the command in the custom app launcher. When I open the program through the panel/launcher (at the top of the screen), the program doesn't load or operate correctly. I get a lot of error messages complaining about being denied permissions. I'm assuming that this is a "superuser/installation/privs" issue, and not a problem with the application (hence this post at superuser.com instead of the application's forums), because when I launch the program from the terminal with sudo, it opens and executes perfectly fine, just like it did the first time around after the install wizard finished. I realize I'm probably going to have to uninstall the program completely, and re-install it differently. Finally, my question: After uninstalling, can I avoid all these issue by just running the installer (sh fooInstaller.sh) right out of my Downloads directory, sans the sudo prefix? If not, how do I get the program to install without root privs so that I can add it to my panel/launcher and get it executing correctly? Sorry for the long post but I didn't want to omit any details because, as I'm sure you can tell, I'm not really sure I know what I'm doing. Thanks for any help here!

    Read the article

  • What is the correct mail set up for multiple domains on one server?

    - by newmarc
    I have a machine (centos 5) with one external ip address. On that machine I have many virtual hosts with a few different top level domain names and sub-domains under those eg. sub1.domain1.com sub2.domain1.com sub3.domain1.com sub1.domain2.com sub2.domain2.com sub1.domain3.com And so on... Alot of these different sites need to send mail as their corresponding domain (or second-level domain at least). I need to set up DKIM, SPF (but that's handled on the DNS) and rDNS lookup so the mail gets received. As I understand it, you can only have one rDNS entry per machine. I could set up a server for each top level domain, but I'm thinking that'll get expensive. What should I do here? Is there a way to have multiple rDNS lookups on one ip address? How do I setup DKIM signing for multiple domain names on the one machine? Are there any services out there that could handle this for me? Thanks for your help...

    Read the article

  • DNS-Based Environment Determination

    - by zvolkov
    Found the following here. The questions is: where can I find more details on how exactly implement this on Windows? Any guide or how-to anybody? Or maybe you can provide your invaluable suggestions? Specifically, how do I make so that "all QA servers would first resolve entries in qa.example.com first and then if that lookup failed they would try example.com" (I'm a dev, not a DNS specialist, but our IT Support has refused to help on this:() Use DNS Based Environment Determination for your servers. Do this by initially splitting your top level domain into a number of sub domains depending on their function, and then creating DNS Service Names in each of the sub domains pointing to the relevant server for that service. Based on the list above we would then have: * clientdb.prod.example.com for Production * clientdb.perf.example.com for Performance Testing * clientdb.qa.example.com for QA * clientdb.dev.example.com for Development Servers then resolve entries in their relevant sub domain by function. That is, all QA servers would first resolve entries in qa.example.com first and then if that lookup failed they would try example.com. This allows you to have a single configuration entry for your client database hostname (clientdb) that would resolve correctly in all environments. This technique has the added advantage of still having global services defined in a common top level domain. This seems to be related to Providing "split horizon" DNS service. Reading that, I see that I will probably need separate DNS Server for each environment. Is this true or does Windows support some form of "tagging" the records to be visible depending on the requestor's IP?

    Read the article

  • Wrong Outlook anywhere settings

    - by Ken Guru
    Hey all I wanted to enable NTLM authentication on OutlookAnywhere, and after doing the command Set-OutlookAnywhere -IISAuthenticationMethods Basic,NTLM, my settings got changed. This is a dump before I run the command: [PS] C:\Windows\system32Get-OutlookAnywhere ServerName : EXCAS01 SSLOffloading : False ExternalHostname : ClientAuthenticationMethod : Basic IISAuthenticationMethods : {Basic} MetabasePath : IIS:///W3SVC/1/ROOT/Rpc Path : C:\Windows\System32\RpcProxy Server : EXCAS01 AdminDisplayName : ExchangeVersion : 0.1 (8.0.535.0) Name : Rpc (Default Web Site) DistinguishedName : CN=Rpc (Default Web Site),CN=HTTP,CN=Protocols,CN= EXCAS01,CN=Servers,CN=Exchange Administrative Grou p (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=Fi rst Organization,CN=Microsoft Exchange,CN=Services ,CN=Configuration,DC=asp,DC=ssc,DC=no Identity : EXCAS01\Rpc (Default Web Site) Guid : 289b4865-caf1-4412-95ee-6fb0dff55e8b ObjectCategory : asp.ssc.no/Configuration/Schema/ms-Exch-Rpc-Http-V irtual-Directory ObjectClass : {top, msExchVirtualDirectory, msExchRpcHttpVirtual Directory} WhenChanged : 05.01.2011 16:59:55 WhenCreated : 27.11.2009 11:20:12 OriginatingServer : IsValid : True Noticde the settings for "Name", "DistinguishedName", and "Identity". After I run the command, I ended up with this: [PS] C:\Windows\system32Get-OutlookAnywhere ServerName : EXCAS01 SSLOffloading : False ExternalHostname : ClientAuthenticationMethod : Basic IISAuthenticationMethods : {Basic, Ntlm} MetabasePath : IIS:///W3SVC/1/ROOT/Rpc Path : C:\Windows\System32\RpcProxy Server : EXCAS01 AdminDisplayName : ExchangeVersion : 0.1 (8.0.535.0) Name : EXCAS01 DistinguishedName : CN=EXCAS01,CN=HTTP,CN=Protocols,CN=EXCAS01,CN=Serv ers,CN=Exchange Administrative Group (FYDIBOHF23SP DLT),CN=Administrative Groups,CN=First Organizatio n,CN=Microsoft Exchange,CN=Services,CN=Configurati on,DC=asp,DC=ssc,DC=no Identity : EXCAS01\EXCAS01 Guid : 289b4865-caf1-4412-95ee-6fb0dff55e8b ObjectCategory : asp.ssc.no/Configuration/Schema/ms-Exch-Rpc-Http-V irtual-Directory ObjectClass : {top, msExchVirtualDirectory, msExchRpcHttpVirtual Directory} WhenChanged : 06.01.2011 09:43:50 WhenCreated : 27.11.2009 11:20:12 OriginatingServer : ASP-DC-2. IsValid : True Now, the "Name", "DistinguishedName" and "Identity" has changed, and when I try to change it back by running "Set-OutlookAnywhere -Identity "EXCAS01\Rpc (Default Web Site)", I get the following error: [PS] C:\Windows\system32Set-OutlookAnywhere -Identity "EXCAS01\Rpc (Default Web Site)" Set-OutlookAnywhere : The operation could not be performed because object 'EXCA S01\Rpc (Default Web Site)' could not be found on domain controller 'ASP-DC-2.'. Remember, the RPC over HTTP works fine with Basic authentication (even with the wrong settings), but NTLM still doesnt work. How do I change back the settings?

    Read the article

  • Kindle (client) for Mac

    - by doug
    So we're clear, i'm talking bout the client/software version here--ie, that you install on your Mac or PC--not the device. The Kindle client was recently released for the Mac. I bought a couple of Kindle-edition books and i'm reading them using this client. Astonishingly, two features i consider to be more or less essential to any ebook reader are missing in the Kindle client, either that, or i can't find them: (i) text searching; and (ii) highlighting text. First, does anyone know how to access the search feature? I'm aware of the "Go To" button at the top middle of the reader window--the options in that menu when you click the button are: "Cover", "Table of Contents", "Beginning" and "Location." "Location" requires that you type in an integer (but it doesn't correspond to page number--e.g., typing "167" brought me to the table of contents), not a search term. Second, there's a button on the upper right-hand corner of the window "Show Notes and Marks" yet i can't find any way to highlight text. The only kind of "note" or "mark" i have been able to record is to "bookmark" a page by clicking the "bookmark" button also at the top of the window.

    Read the article

  • centos TCP/IP connection very slow

    - by yuli chika
    I have a VSP (centos6.1 64bit) with 4gb ram. It always runs well, but in recent few days, the server become slowly. open a small css file need 22 seconds(2kb). tested in home/office/phone with (IE,chrome,safari,firefox). see in firebug networking DNS Lookup ?4?ms Connecting ?21.18?s Sending 1?ms Waiting ?115?ms Receiving ?9?ms The connection cost 21.18 seconds I have checked all the log file, there have no error. top commond, still have free memory. top - 00:23:15 up 8 days, 3:57, 1 user, load average: 3.60, 3.42, 3.83 Tasks: 221 total, 4 running, 217 sleeping, 0 stopped, 0 zombie Cpu(s): 19.3%us, 3.2%sy, 0.0%ni, 76.1%id, 1.4%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4194304k total, 3247724k used, 946580k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32357 mysql 15 0 3710m 835m 6268 S 34.5 20.4 39:14.40 mysqld 9780 apache 15 0 442m 59m 12m S 33.2 1.4 0:05.69 httpd 9842 apache 15 0 403m 26m 10m S 16.9 0.7 0:01.23 httpd 9847 apache 15 0 412m 45m 22m R 15.3 1.1 0:01.00 httpd 9834 apache 15 0 426m 46m 11m R 13.0 1.1 0:02.22 httpd 9891 apache 15 0 407m 43m 19m S 8.0 1.1 0:00.33 httpd 9845 apache 15 0 414m 51m 24m S 6.0 1.3 0:01.53 httpd 9827 apache 15 0 402m 28m 11m S 3.3 0.7 0:02.69 httpd 9768 apache 16 0 414m 51m 24m S 3.0 1.3 0:06.51 httpd 9889 root 15 0 211m 12m 8160 S 2.7 0.3 0:00.32 php 9702 apache 15 0 415m 55m 26m S 1.7 1.4 0:10.67 httpd 9844 apache 15 0 413m 47m 21m S 1.7 1.2 0:01.21 httpd 9697 apache 15 0 414m 51m 24m S 1.3 1.3 0:11.05 httpd 9778 apache 15 0 414m 53m 25m S 1.3 1.3 0:05.38 httpd 9772 apache 15 0 414m 51m 23m R 0.7 1.3 0:05.04 httpd 9823 apache 15 0 415m 50m 23m S 0.7 1.2 0:03.97 httpd 9837 apache 15 0 402m 27m 11m S 0.3 0.7 0:01.04 httpd Then, how to check where is the problem and fixed it? I haven't change and config files in these days. Thanks.

    Read the article

  • ServerName wildcards in Apache name-based virtual hosts?

    - by Martijn Heemels
    On our LAN I've set up several 'fake' TLDs in the DNS server, with the intention of using them for Apache name-based virtual hosting. I'd like to combine this with mass-virtual-hosting (i.e. VirtualDocumentRoot) on an Ubuntu 10.04 LAMP server. However, I can't get it to select the right vhost! Here is a summary of the Apache config: NameVirtualHost 10.10.0.205 <VirtualHost 10.10.0.205> ServerName *.test VirtualDocumentRoot /var/www/%-3.0.%-2/test/%1/ CustomLog /var/log/apache2/access.log vhost_combined </VirtualHost> <VirtualHost 10.10.0.205> ServerName *.dev VirtualDocumentRoot /var/www/%-3.0.%-2/dev/%1/ CustomLog /var/log/apache2/access.log vhost_combined </VirtualHost> A hostname such as www.domain.com.dev, correctly resolves to 10.10.0.205, but always selects the top vhost, instead of the bottom one, which matches more closely. I was under the impression that Apache would first try to match the ServerName before defaulting to the top vhost for a given IP. What am I doing wrong? Or is this not possible and must I use another IP for each TLD? apachectl -S outputs (trimmed): 10.10.0.205:* is a NameVirtualHost default server *.test port * namevhost *.test port * namevhost *.dev

    Read the article

< Previous Page | 177 178 179 180 181 182 183 184 185 186 187 188  | Next Page >