Search Results

Search found 9976 results on 400 pages for 'identity map'.

Page 183/400 | < Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• BGP path prepended route not listed anywhere

  - by Julien Vehent

  We have a simple multi-homed setup with two routers that advertise our AS to two ISP. The second ISP (ISP B) is only used for backup when ISP A goes down, so we prepended our AS 3 times on this route. I spend a couple of hours this morning poking at looking glass routers all over the internet, and none of them list our backup route with the prepended path. I checked the south african internet exchange, the london internet exchange, oregon internet exchange and a couple dozen ISPs. All of them have multiples routes through ISP A, often with 3 or 4 hops. The route through ISP B should, at least, appear somewhere and have 5 or 6 hops. But I couldn't find it anywhere. (I checked the full bgp tables on the looking glass routers, using show ip bgp 65000) My questions are: Is there a limit to the size of a route after which most routers will simply discard the route ? Is our backup route even going to work when ISP A goes down, if no router knows about it ? Our two routers are connected on iBGP. Would it be possible that the route through ISPB is not announced because the iBGP session prefers the route through ISPA ? This is what non-exist-map and advertise-map are supposed to do, but none of those are used in either routers.

  Read the article

• Join mp4 files in linux

  - by Jose Armando

  I want to join two mp4 files to create a single one. The video streams are encoded in h264 and the audio in aac. I can not re-encode the videos to another format due to computational reasons. Also, I cannot use any gui programs, all processing must be performed with linux command line utilities. FFmpeg cannot do this for mpeg4 files so instead I used MP4Box e.g. MP4Box -add video1.mp4 -cat video2.mp4 newvideo.mp4 unfortunately the audio gets all mixed up. I thought that the problem was that the audio was in aac so I transcoded it in mp3 and used again MP4Box. In this case the audio is fine for the first half of newvideo.mp4 (corresponding to video1.mp4) but then their is no audio and I cannot navigate in the video also. My next thought was that the audio and video streams had some small discrepancies in their lengths that I should fix. So for each input video I splitted the video and audio streams and then joined them with the -shortest option in ffmpeg. thus for the first video I ran avconv -y -i video1.mp4 -c copy -map 0:0 videostream1.mp4 avconv -y -i video1.mp4 -c copy -map 0:1 audiostream1.m4a avconv -y -i videostream1.mp4 -i audiostream1.m4a -c copy -shortest video1_aligned.mp4 similarly for the second video and then used MP4Box as previously. Unfortunately this didn't work either. The only success I had was when I joined the video streams separetely (i.e. videostream1.mp4 and videostream2.mp4) and the audio streams (i.e. audiostream1.m4a and audiostream2.m4a) and then joined the video and audio in a final file. However, the synchronization is lost for the second half of the video. Concretelly, there is a 1 sec delay of audio and video. Any suggestions are really welcome.

  Read the article

• XP Client for NFS failure dialog on startup, but drive mapping works

  - by Matt Bennett

  I'm mounting an NFS share to some windows machines using the tools that come in the Services for UNIX Administration toolkit. I've set up the User Name Mapping service to use local passwd and group files. I had to manually start the User Name Mapping service, and then created an 'advanced map' from the XP machine's user to a uid that exists in on my NFS server, like so: Windows User: Matt Bennett UNIX Domain: PCNFS UNIX User: mattbennett UID: 10250 Primary: * I can map a network drive without any issues, and it correctly identifies the UID and GID to use, but when I reboot I get this message: "An error occurred while connecting to the NFS server. Make sure that the Client for NFS service has started. If the problem persists make sure Client for NFS service can communicate with User Name Mapping or PCNFS server." After dismissing the dialog, the machine finishes booting and the network drive is there in My Computer with the title "Disconnected Network Drive", but I can open it I can see the network share without a problem, and then it drops the 'disconnected' from its title. It seems like the services are starting in the wrong order or something, so the first attempt to connect fails but subsequent ones work as expected. There don't seem to be any symptoms apart from the dialog box, but obviously something's not quite right. What have I done wrong? Thanks, Matt.

  Read the article

• How to Upload a file from client to server using OFBIZ?

  - by SIVAKUMAR.J

  Hi all, Im new to ofbiz.So is my question is have any mistake forgive me for my mistakes.Im new to ofbiz so i did not know some terminologies in ofbiz.Sometimes my question is not clear because of lack of knowledge in ofbiz.So try to understand my question and give me a good solution with respect to my level.Because some solutions are in very high level cannot able to understand for me.So please give the solution with good examples. My problem is i created a project inside the ofbiz/hot-deploy folder namely "productionmgntSystem".Inside the folder "ofbiz\hot-deploy\productionmgntSystem\webapp\productionmgntSystem" i created a .ftl file namely "app_details_1.ftl" .The following are the coding of this file <html> <head> <meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1"> <title>Insert title here</title> <script TYPE="TEXT/JAVASCRIPT" language=""JAVASCRIPT"> function uploadFile() { //alert("Before calling upload.jsp"); window.location='<@ofbizUrl>testing_service1</@ofbizUrl>' } </script> </head> <!-- <form action="<@ofbizUrl>testing_service1</@ofbizUrl>" enctype="multipart/form-data" name="app_details_frm"> --> <form action="<@ofbizUrl>logout1</@ofbizUrl>" enctype="multipart/form-data" name="app_details_frm"> <center style="height: 299px; "> <table border="0" style="height: 177px; width: 788px"> <tr style="height: 115px; "> <td style="width: 103px; "> <td style="width: 413px; "><h1>APPLICATION DETAILS</h1> <td style="width: 55px; "> </tr> <tr> <td style="width: 125px; ">Application name : </td> <td> <input name="app_name_txt" id="txt_1" value=" " /> </td> </tr> <tr> <td style="width: 125px; ">Excell sheet &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;: </td> <td> <input type="file" name="filename"/> </td> </tr> <tr> <td> <!-- <input type="button" name="logout1_cmd" value="Logout" onclick="logout1()"/> --> <input type="submit" name="logout_cmd" value="logout"/> </td> <td> <!-- <input type="submit" name="upload_cmd" value="Submit" /> --> <input type="button" name="upload1_cmd" value="Upload" onclick="uploadFile()"/> </td> </tr> </table> </center> </form> </html> the following coding is present in the file "ofbiz\hot-deploy\productionmgntSystem\webapp\productionmgntSystem\WEB-INF\controller.xml" ...... ....... ........ <request-map uri="testing_service1"> <security https="true" auth="true"/> <event type="java" path="org.ofbiz.productionmgntSystem.web_app_req.WebServices1" invoke="testingService"/> <response name="ok" type="view" value="ok_view"/> <response name="exception" type="view" value="exception_view"/> </request-map> .......... ............ .......... <view-map name="ok_view" type="ftl" page="ok_view.ftl"/> <view-map name="exception_view" type="ftl" page="exception_view.ftl"/> ................ ............. ............. The following are the coding present in the file "ofbiz\hot-deploy\productionmgntSystem\src\org\ofbiz\productionmgntSystem\web_app_req\WebServices1.java" package org.ofbiz.productionmgntSystem.web_app_req; import javax.servlet.http.HttpServletRequest; import javax.servlet.http.HttpServletResponse; import java.io.DataInputStream; import java.io.FileOutputStream; import java.io.IOException; public class WebServices1 { public static String testingService(HttpServletRequest request, HttpServletResponse response) { //int i=0; String result="ok"; System.out.println("\n\n\t*************************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response)- Start"); String contentType=request.getContentType(); System.out.println("\n\n\t*************************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response)- contentType : "+contentType); String str=new String(); // response.setContentType("text/html"); //PrintWriter writer; if ((contentType != null) && (contentType.indexOf("multipart/form-data") >= 0)) { System.out.println("\n\n\t**********************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response) after if (contentType != null)"); try { // writer=response.getWriter(); System.out.println("\n\n\t**********************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response) - try Start"); DataInputStream in = new DataInputStream(request.getInputStream()); int formDataLength = request.getContentLength(); byte dataBytes[] = new byte[formDataLength]; int byteRead = 0; int totalBytesRead = 0; //this loop converting the uploaded file into byte code while (totalBytesRead < formDataLength) { byteRead = in.read(dataBytes, totalBytesRead,formDataLength); totalBytesRead += byteRead; } String file = new String(dataBytes); //for saving the file name String saveFile = file.substring(file.indexOf("filename=\"") + 10); saveFile = saveFile.substring(0, saveFile.indexOf("\n")); saveFile = saveFile.substring(saveFile.lastIndexOf("\\")+ 1,saveFile.indexOf("\"")); int lastIndex = contentType.lastIndexOf("="); String boundary = contentType.substring(lastIndex + 1,contentType.length()); int pos; //extracting the index of file pos = file.indexOf("filename=\""); pos = file.indexOf("\n", pos) + 1; pos = file.indexOf("\n", pos) + 1; pos = file.indexOf("\n", pos) + 1; int boundaryLocation = file.indexOf(boundary, pos) - 4; int startPos = ((file.substring(0, pos)).getBytes()).length; int endPos = ((file.substring(0, boundaryLocation)).getBytes()).length; //creating a new file with the same name and writing the content in new file FileOutputStream fileOut = new FileOutputStream("/"+saveFile); fileOut.write(dataBytes, startPos, (endPos - startPos)); fileOut.flush(); fileOut.close(); System.out.println("\n\n\t**********************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response) - try End"); } catch(IOException ioe) { System.out.println("\n\n\t*********************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response) - Catch IOException"); //ioe.printStackTrace(); return("exception"); } catch(Exception ex) { System.out.println("\n\n\t*********************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response) - Catch Exception"); return("exception"); } } else { System.out.println("\n\n\t********************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response) else part"); result="exception"; } System.out.println("\n\n\t*************************************\n\tInside WebServices1.testingService(HttpServletRequest request, HttpServletResponse response)- End"); return(result); } } I want to upload a file to the server.The file is get from user "<input type="file"..> tag in the "app_details_1.ftl" file & it is updated into the server by using the method "testingService(HttpServletRequest request, HttpServletResponse response)" in the class "WebServices1".But the file is not uploaded. Give me a good solution for uploading a file to the server. Thanks & Regards, Sivakumar.J

  Read the article

• scan partition for bad blocks

  - by user22559

  Hello everyone I have a hard disk with bad sectors on it. I want to partition the drive so that the partitions are in the good part of the hard disk, and the parts that have bad sectors are not used. The first ~20GB of the hard disk are good. Then comes a ~13GB part that is riddled with bad sectors. After that, the hard disk is good again, but at the very end there is a ~2GB part with bad sectors. I have used an app called "Hdtune" to get this information, and I have created a 19GB c: partition at the beginning of the drive, then skipping the 13GB of bad sectors, then creating the D: partition that spans the rest of the disk, minus the last 2GB. The C: partition works well (i have been using it for a month and i have got no error whatsoever), but the D partition has been giving me problems. Somehow, it seems that I have some bad sectors in the D: partition. I am looking for an app that scans the HDD, finds the bad blocks, and shows them in a map so I can see if they are in the D partition. Or, an app that scans only a specified partition for bad sectors, and then shows in a map where the bad sectors are in the partition. I want to know this so I can resize the D partition so that it is outside of the bad area of the disk.

  Read the article

• Cannot access server shares over VPN

  - by DuncanDavies

  I've set up a single hosted server to use as a development environment for a web-based application. The web app is served up fine on port 80, however I'm struggling to get my VPN to behave how I'd expect so the developers don't have the access they require. The VPN connects fine and I can access the back-end database (SQL Server) which resides on the server with the client tools from the laptops. However they cannot access any shared folders. The server's local IP address is 10.x.x.x, and I've assigned a static IP address pool to RRAS (of 192.168.100.1 - 20). The clients pick up a valid IP Address (i.e. 192.168.100.9) when they connect. There is no name resolution setup, DNS or WINS. When connected via VPN the clients can ping the server (192.168.100.1) by IP Address, but cannot map a drive to a shared folder (net use * \\192.168.100.1\xxxxx) - I get 'System error 53 has occurred. The network path was not found.' I don't understand why I can ping by the ip, but not map by it. Some details: Server OS is Windows 2008 (Datacenter) VPN is SSTP using RRAS Clients are all Windows 7 I've tried temporarily disabling the firewalls So, why can we not access the file system when everything else (ping, RDP, SQL Server clients tools) works? Thanks for your help Duncan

  Read the article

• Cannot find network path for computer in workgroup of home Windows XP PCs

  - by John Galt

  VMWare Workstation 6.5 is running as an app on a Windows Vista 64bit PC host. Thanks to Workstation we have 2 guest machines running: TerriVM and MattVM (both of these run Windows XP SP2). We are attempting to get virtual networking configured so we can access the files of both of these VM guest systems from other real PCs connected to this home network. We think we are close but we can't quite get it right... Here is what we've done so far: * On VM Workstation, we set "Host Virtual Network Mapping" to use VMnet0 with the setting "Bridge to an automatically chosen adapter". * On each VM guest (i.e. using Windows explorer on XP), we rightmouse on the C disk, click "Sharing" tab, set shareName to "C_Disk" and check both boxes labeled "Share this folder on the network" and "Allow network users to change my files". Symptoms: On "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \TerriVM\C_Disk and assign drive letter T. We see all the folders on this shared drive and can open files on them. So that is good. On same "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \MattVM\C_Disk and assign drive letter M. We get a message box "_The network path \mattvm\C_Disk could not be found_". Alternatively, we type just \mattvm\ into the Folder box and click "Browse" and get a dialog box where we drill down from "Entire Network" to "Microsoft Windows Network" to "Workgroup" where both TerriVM and MattVM are listed as computers on the network. Clicking the + sign next to MattVM gives an hourglass and never enables the OK button and I have to cancel. In summary, I think we've attempted to share both of these virtual machines using the same techniques and connect to them in similar fashion, but one connects properly and the other machine can be seen but no shared resources on it can be accessed. Can anyone suggest something possibly overlooked or something to try? Thanks so much in advance.

  Read the article

• How to make network drives appear even if disconnected?

  - by Jake

  I have the same problem as many others: network and home drives set by group policy and AD are not connected on windows startup. The prime suspect is that the LAN or wireless does not connect until after user log in. I have already given up on that. Now, I just want the disconnected drives to continue to list in My Computer so that if the user goes in and double click the drive, it will connect again. However, on some machines the drive is completely missing from My Computer. If I right click My Computer Map Network Drive again, it does work. But it's very troublesome to do it all the time. And I don't want to use a script to map the drives because I don't want to appear to be using a hacky solution to the users. The drives listed as disconnected will look more like a "built-in feature", and gives users more confidence. How can I keep the disconnected drives in My Computer? I am using Windows 7 Professional and Win2k8.

  Read the article

• Intermittent 5.7.1 email bounce to Exchange 2007

  - by Steve Kennaird

  My knowledge of Exchange isn't particularly great, so excuse me if some of the terminology I use isn't quite right. I'm primarily a web developer who's now responsible for a small business's network. We have a server running SBS 2008 and Exchange 2007. Generally, everything works well, emails are able to be sent to both internal and external domains without issue. We've only got ~20 users, Exchange is sitting on a single server. I use SendGrid to send emails generated by our externally hosted website to users in the office. Primarily, order notifications are sent to [email protected]. Without any pattern and less than once per week on average, an email to [email protected] will bounce back, and the logs on SendGrid detail the following error: 550 5.7.1 Unable to relay for [email protected] Either side of that failed delivery attempt, I'm able to send and receive emails to/from [email protected]. Having done some research, incorrect reverse DNS seems like it could be a cause of intermittent bounces like this. Having used nslookup, I have found that the reverse DNS doesn't map like it should, e.g. Office IP: 135.325.351.123 (made up IP, for example only) Domain: office.somedomain.com (made up, for example only) Reverse DNS: somedomain.gotadsl.co.uk (half made up) Could this be a cause? I'm sure that the IP address and the domain should map to each other. Also, it has been suggested to me that as the Exchange server is on a network with an ADSL connection, that could be a potential cause as the connection "goes up and down all day long". I don't have an opinion on this, as I don't have enough knowledge of Exchange/ADSL to form a reliable opinion. Can anyone offer any insight as to whether one or both are actually potential causes, or if there is another possible cause?

  Read the article

• lsof not showing what port a proc is listening on

  - by ericslaw

  I have many processes on a box listening on several ports. I am trying to map ports to pids. The problem is that lsof is not telling me what ports belong to which process. Given an apache listening on port 80, I can see it listening via netstat: user@host% netstat -an|grep LISTEN|grep 80 *.80 *.* 0 0 49152 0 LISTEN But when I try to map port 80 to a pid I get nothing: user@host% lsof -iTCP:80 -t When I try seeing what sockets that specific pid is using I get: user@host% lsof -lnP -p31 -a -i COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME libhttpd. 31 0 15u IPv4 0x6002d970b80 0t0 TCP *:65535 (LISTEN) Notice the *:65535 in the NAME column. Does anyone know why lsof is not reporting the port in use? I am running as root. I am using a mix of lsof and os versions: lsof v4.77 on Solaris10 sparc lsof v4.72 on Redhat4.2 etc I know that linux solutions can use "netstat -p", so I guess I'm only looking for why solaris isn't working, but I find lsof is frequently silent and not showing me expected data.

  Read the article

• Administrative shares in Windows 7 Pro not visible

  - by Chris Tybur

  My desktop machine has a clean install of Windows 7 Professional. For some reason the standard administrative shares Admin$, C$, D$, etc are not visible, either in Computer Management - Shared Folders - Shares or via net share. I also have a laptop with a clean install of Windows 7 Professional, and I can see the admin shares in both places. As such, I can map to \\laptop\c$ from the desktop, but I can't map to \\desktop\c$ from the laptop. I pretty much took the defaults during the Windows 7 installations. I've tried adding LocalAccountTokenFilterPolicy to the registry on the desktop, but that didn't work. On the desktop I've also disabled UAC, turned off Windows firewall, removed it from a homegroup, made sure file and printer sharing is turned on, but nothing has worked. There is some subtle difference between the two machines that I can't seem to find. I'm logging into both machines using a local account that is in the Administrators group. Both accounts have the same name and password. I really don't want to have to create a new share for the desktop's C drive, especially since C$ is visible and working on the laptop and therefore I should be able to make it work on the desktop. Any idea why the admin shares would work on one machine and not another? Or why LocalAccountTokenFilterPolicy would fail?

  Read the article

• Should I expect ICMP transit traffic to show up when using debug ip packet with a mask on a Cisco IOS router?

  - by David Bullock

  So I am trying to trace an ICMP conversation between 192.168.100.230/32 an EZVPN interface (Virtual-Access 3) and 192.168.100.20 on BVI4. # sh ip access-lists 199 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 # sh debug Generic IP: IP packet debugging is on for access list 199 # sh ip route | incl 192.168.100 192.168.100.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.100.0/24 is directly connected, BVI4 S 192.168.100.230/32 [1/0] via x.x.x.x, Virtual-Access3 # sh log | inc Buff Buffer logging: level debugging, 2145 messages logged, xml disabled, Log Buffer (16384 bytes): OK, so from my EZVPN client with IP address 192.168.100.230, I ping 192.168.100.20. I know the packet reaches the router across the VPN tunnel, because: policy exists on zp vpn-to-in Zone-pair: vpn-to-in Service-policy inspect : acl-based-policy Class-map: desired-traffic (match-all) Match: access-group name my-acl Inspect Number of Half-open Sessions = 1 Half-open Sessions Session 84DB9D60 (192.168.100.230:8)=>(192.168.100.20:0) icmp SIS_OPENING Created 00:00:05, Last heard 00:00:00 ECHO request Bytes sent (initiator:responder) [64:0] Class-map: class-default (match-any) Match: any Drop 176 packets, 12961 bytes But I get no debug log, and the debugging ACL hasn't matched: # sh log | inc IP: # # sh ip access-lists 198 Extended IP access list 198 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 Am I going crazy, or should I not expect to see this debug log? Thanks!

  Read the article

• FFmpeg convert video w/ dropped frames, out of sync

  - by preahkumpii

  I recorded a video using Bandicam with the MJPEG encoder to get the least amount of lag. Now, I am trying to convert that massive file to a h264 avi using ffmpeg. I know there are dropped frames in the video stream...more than 100 in the first two minutes, which I assume is simply because Bandicam dropped some when it couldn't keep up. So, when I convert the file to h264, the video and audio are out of sync, and appear to be more and more out of sync as output video progresses. Here is my basic command in ffmpeg: ffmpeg -i "C:\...\input.avi" -vcodec libx264 -q 5 -acodec libmp3lame -ar 44100 -ac 2 -b:a 128k "C:\...\output.avi" I have tried EVERYTHING I can think of including: -itsoffset [-]00:00:01 Tried this before and after input file. This doesn't work because as the video progresses it becomes more and more out of sync. -async 1 Doesn't work. -vsync 1 Doesn't work, but it does show dropped frames being duplicated. Two inputs of same file with mapping using -map 0:0 -map 1:1. Doesn't work. The source plays just fine. Any ideas how to convert it with ffmpeg and keep the audio and video synced? Thanks.

  Read the article

• Setup my domain at Whois.com as nameservers for a Dedicated Server with Kloxo

  - by BoDiE2003

  Hello, this is my first time at ServerFault, I'm a stackoverflow user. I'm faceing the next problem and may be its me, but I can't find proper guides to set up a domain and nameservers for a dedicated box. I have a domain, at whois.com, and a Dedicated server at Reliable Hosting Services, the server has 5 IPs, I know that I need 2 of them for the nameservers. Right now, my domain at whois.com is using nsX.whois.com nameservers and it has 2 child nameservers: ns1.mydomain.com & ns2.mydomain.com pointing to those 2 IPs from my Server. Whats next? I still cannot set that domain as my main server domain since it says: To map an IP to a domain, the domain must ping to the same IP, otherwise, the domain will stop working. The domain you are trying to map this IP to, doesn't resolve back to the IP, and so it cannot be set as the default domain for the IP. Well and I'm stuck on those steps, whats next to have my nameservers working and my main domain assigned to my server? Thank you very much and happy new year!!

  Read the article

• Windows 7 Professional Cannot Connect to Share - Wrong password

  - by henryford

  I know that this question has actually been asked a few times before, but every solution I found didn't yield any results on my end, I can't get my head around it: When I am trying to connect to a share on the network, I always get the response "The specified network password is incorrect". However, the password is definetly correct and it works if I connect from another machine. I changed the LAN Manager authentication level to "Send LM & NTLM - use NTLMv2 session security if negiotated", I configured Kerberos encryption types to include all suites, rebooted (several times), but still - no luck. I can connect if I use my regular account with which I am logged in, but I need to connect with a different user since my log-in user has not enough privileges on the share. When I do that, the error above comes up. I'm really frustrated at the moment, this problem is driving me crazy. I'd be gladful for any possible solution to this. At the moment I'm using a workaround: I connect to a different machine via RDP, login with the user I have to use for the network-share connection and then I can map the drive and copy/paste from the RDP session to my local workstation. This is also working when I am connecting via RDP with my current login user and map the drive with the other user who has sufficent privileges. Tanks in advance, Thomas

  Read the article

• Puppet write hosts using api call

  - by Ben Smith

  I'm trying to write a puppet function that calls my hosting environment (rackspace cloud atm) to list servers, then update my hosts file. My get_hosts function is currently this: require 'rubygems' require 'cloudservers' module Puppet::Parser::Functions newfunction(:get_hosts, :type => :rvalue) do |args| unless args.length == 1 raise Puppet::ParseError, "Must provide the datacenter" end DC = args[0] USERNAME = DC == "us" ? "..." : "..." API_KEY = DC == "us" ? "..." : "..." AUTH_URL = DC == "us" ? CloudServers::AUTH_USA : CloudServers::AUTH_UK DOMAIN = "..." cs = CloudServers::Connection.new(:username => USERNAME, :api_key => API_KEY, :auth_url => AUTH_URL) cs.list_servers_detail.map {|server| server.map {|s| { s[:name] + "." + DC + DOMAIN => { :ip => s[:addresses][:private][0], :aliases => s[:name] }}} } end end And I have a hosts.pp that calls this and 'should' write it to /etc/hosts. class hosts::us { $hosts = get_hosts("us") hostentry { $hosts: } } define hostentry() { host{ $name: ip => $name[ip], host_aliases => $name[aliases] } } As you can imagine, this isn't currently working and I'm getting a 'Symbol as array index at /etc/puppet/manifests/hosts.pp:2' error. I imagine, once I've realised what I'm currently doing wrong there will be more errors to come. Is this a good idea? Can someone help me work out how to do this?

  Read the article

• Emacs 24.1: How do I restore i-search Ctrl-Y behavior from older versions?

  - by Eric

  In emacs 24.1, when you do Ctrl-Y in an interactive search, it yanks the kill buffer into the search string ("it pastes the clipboard contents" in any-other-app's language) and tries to match it. In the last 20 versions or so, pressing Ctrl-Y matches the rest of the current line. I have two very common use cases: Match this line, revert the buffer, and search for the line (less often:) Where else is this text in the buffer? I tried modifying /lisp/isearch.el, switching the bindings for isearch-yank-line (which I want) and isearch-yank-kill (which I'm fine binding to the ridiculous \M-s\C-e key sequence). But I don't think this file even gets picked up. But I don't think this file even gets loaded. If I explicitly load it, I still get the 24.1 behavior. Here's my change: (add-hook 'isearch-mode-hook (lambda () (define-key isearch-mode-map "\C-y" 'isearch-yank-line) (define-key isearch-mode-map "\M-s\C-e" 'isearch-yank-kill) )) No change in the behavior. I even tried hacking isearch.el, still no change. This is on Windows btw, but I suspect it doesn't matter. Could someone tell me how I can restore the old binding?

  Read the article

• Creating a partitioned raid1 array for booting a debian squeeze system

  - by gucki

  I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 --raid-devices=2 /dev/sda /dev/sdb This gave a warning about metadata being 1.2 and my system might not boot. I cannot use 0.9 because it restricts the size of the raid to 2TB and I assume grub shipped with latest debian (squeeze) should be able to handle metadata 1.2. So then I created the needed partitions like this: # creating new label (partition table) parted -s /dev/md0 mklabel 'msdos' # creating partitions sfdisk -uM /dev/md0 << EOF 0,4096 ,1024,S ; EOF # making root filesystem mkfs -t ext4 -L boot -m 0 /dev/md0p1 # making swap filesystem mkswap /dev/md0p2 # making data filesystem mkfs -t ext4 -L data /dev/md0p3 Then I mounted the root partition, copied a minimal debian install inside and temporary mounted /dev /proc /sys. Afer this I chrooted to the new root folder and executed: grub-install --no-floppy --recheck /dev/md0 However this fails badly with: /usr/sbin/grub-probe: error: unknown filesystem. Auto-detection of a filesystem of /dev/md0p1 failed. Please report this together with the output of "/usr/sbin/grub-probe --device-map=/boot/grub/device.map --target=fs -v /boot/grub" to I don't think it's a bug in grub (so I didn't report it yet) but a fault of mine. So I really wonder how to properly setup my raid1, everything I tried so far failed.

  Read the article

• Subdomain is preventing my search results from rising as expected in page rank

  - by culov

  My problem is that I have a site which has requires a dedicated page for every city I choose to support. Early on, I decided to use subdomains rather than a directly after my domain (ie i used la.truxmap.com rather than truxmap.com/la). I realize now that this was a major mistake because Google seems to treat la.truxmap.com as a completely different site as ny.truxmap.com. So for instance, if i search "la food truck map" my site will be near the top, however, if i search "nyc food truck map" im no where in sight because ny.truxmap.com wouldnt be very high in the page rank by itself, and it doesnt have the boost that it ought to be getting from the better known la.truxmap.com So a mistake I made a year ago is now haunting my page rank. I'd like to know what the most painless way of resolving my dilemma might be. I have received so much press at la.truxmap.com that I can't just kill the site, but could I re-direct all requests at la.truxmap.com to truxmap.com/la and do the same for all cities supported without trashing my current, satisfactory page rank results I'm getting from la.truxmap.com ?? EDIT I left out some critical information. I am using Google Apps to manage my domain (that is, to add the subdomains) and Google App Engine to host my site. Thus, Google Apps provides a simple mechanism to mask truxmap.appspot.com (the app engine domain) as la.truxmap.com, but I don't see how I can mask it as truxmap.com/la. If I can get this done, then I can just 301 redirect la.truxmap.com to truxmap.com/la as suggested below. Thanks so much!

  Read the article

• stopping fastcgi_cache for php-enabled custom error page

  - by Ian

  Since enabling the fastcgi_cache on my nginx server, my php-enabled custom error page has suddenly stopped working and I'm getting the internal 404 message instead. In nginx.conf: fastcgi_cache_path /var/lib/nginx/fastcgicache levels=1:2 keys_zone=MYCACHE:5m inactive=2h max_size=1g loader_files=1000 loader_threshold=2000; map $http_cookie $no_cache { default 0; ~SESS 1; } fastcgi_cache_key "$scheme$request_method$host$request_uri"; add_header X-My-Cache $upstream_cache_status; map $uri $no_cache_dirs { default 0; ~^/(?:phpMyAdmin|rather|poll|webmail|skewed|blogs|galleries|pixcache) 1; } the cache relevant stuff in my fastcgi.conf: fastcgi_cache MYCACHE; fastcgi_keep_conn on; fastcgi_cache_bypass $no_cache $no_cache_dirs; fastcgi_no_cache $no_cache $no_cache_dirs; fastcgi_cache_valid 200 301 5m; fastcgi_cache_valid 302 5m; fastcgi_cache_valid 404 1m; fastcgi_cache_use_stale error timeout invalid_header updating http_500; fastcgi_ignore_headers Cache-Control Expires; expires epoch; fastcgi_cache_lock on; If I disable the fastcgi_cache, the php-enabled 404 page works as it has for years. How would I disable the cache for the custom error page?

  Read the article

• screen scraper templates for various websites

  - by intuited

  I'm looking specifically for a convenient way to locally archive posts from this and other similar sites. I'd like to separate the question itself from the answers, or maybe crop the question and store it, keeping the page title. Obviously I don't need to store the menu or the various other site interface chrome. The best way to do this would seem to be to associate an XSLT template with a match on the URL and use that template to pull the various relevant informations and format them. My two-part question: Is there a tool specifically built for this task? I.E. something that takes a URL and checks it against a map of path-matching expressions to templates, and outputs the result of applying the template to that resource? xmlto seems to be most of the way there, and could probably just be called from a script that does the pattern-matching, but something already integrated would be more convenient. Is such a URL_pattern-to-XSLT_template map publicly available somewhere? Question 2.5: Is it legal to do this with sites like this one that have public licenses on their content?

  Read the article

• Questions for anyone who has used Sun Type 7 keyboards

  - by Irinotecan

  So I noticed that Oracle is still selling Sun Type 7 keyboard and mouse packages. I was thinking of buying one for a Linux box at my house so I had easy access to some of the extra keys such as Compose and Alt-GR. I have some questions though before I do for anyone who has used these -- it's been a very long time since I've used an actual Sun keyboard. They show that both a PC and UNIX layout is available. Unfortunately, I cannot find anywhere a clear picture of both layouts to determine the difference. Can anyone post pictures of the 2 different layouts for me to take a look at? I don't remember what some of the "Solaris shortcut" keys do, like Props, Front, Stop, and Again. Are these vestiges from OpenWindows? Do they have any usage on a modern Solaris like OpenSolaris running Gnome? Do they automatically map to anything useful on Linux, or am I going to have to map them myself to something with XModMap? When I last used a Sun keyboard, I remember it having a rather mushy feel to it, so I am wondering if any touch typists could weigh in on whether this keyboard "feels nice" for day to day touch typing. Thanks!

  Read the article

• Failed Software RAID0 on Linux - Attempting to recover data

  - by Gizmo_the_Great

  I have a two disk RAID0 software raid (not hardware raid) that is reported to have failed during boot and my OS won't start. Using a Live CD, I get the following output : sudo mdadm -E /dev/sdc1 /dev/sdd1 /dev/sdc1: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 3710713d:fb301031:84b61247:d1d53e0f Name : HP-xw9300:0 Creation Time : Sun Sep 1 15:22:26 2013 Raid Level : -unknown- Raid Devices : 0 Avail Dev Size : 1465145328 (698.64 GiB 750.15 GB) Data Offset : 16 sectors Super Offset : 8 sectors State : active Device UUID : ad427cd2:9f885f57:7f41015f:90f8f6af Update Time : Sun Jun 8 12:35:11 2014 Checksum : a37407ff - correct Events : 1 Device Role : spare Array State : ('A' == active, '.' == missing) /dev/sdd1: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 3710713d:fb301031:84b61247:d1d53e0f Name : HP-xw9300:0 Creation Time : Sun Sep 1 15:22:26 2013 Raid Level : -unknown- Raid Devices : 0 Avail Dev Size : 976771056 (465.76 GiB 500.11 GB) Data Offset : 16 sectors Super Offset : 8 sectors State : active Device UUID : 2ea0199d:cb08d9e7:0830448a:a1e1e348 Update Time : Sun Jun 8 13:06:19 2014 Checksum : 8883c492 - correct Events : 1 Device Role : spare Array State : ('A' == active, '.' == missing) GParted lists both disks, detects the flags as 'Raid' and lists the data usage. Can anyone please help me re-assemble just so that I can copy some of the data off that I have not backed up recently? Thanks

  Read the article

< Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >