Search Results

Search found 5373 results on 215 pages for 'wireless bridge'.

Page 183/215 | < Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >

• xrandr fails when 3rd monitor has higher resolution

  - by Pi3cH

  I tried many combinations with xrandr command under lubuntu 12.04 to setup my three monitors DVI (DELL 1) left detected as HDMI1 HDMI (LG E2290) middle detected as HDMI2 VGA (DELL 2) right detected as VGA1 I can get the display with fix 1280x1024 on all the monitors. But once I setup 1280x1024 + 1920x1080 + 1280x1024, I get blank screen on all the monitors. Sometimes it throws crts fail error instead of blanking out. Anyone have similar issues? any solutions/workarounds? P.S. I can setup two monitors using 1280x1280 and 1920x1080 P.S.S. HDMI2 required at least 1920x1080 to display sharp picture. Outputs (it seems graphic card supports up to 8192x8192): xrandr Screen 0: minimum 320 x 200, current 3840 x 1024, maximum 8192 x 8192 VGA1 connected 1280x1024+2560+0 (normal left inverted right x axis y axis) 338mm x 270mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI1 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI2 connected 1280x1024+1280+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0 + 1680x1050 60.0 1280x1024 75.0 60.0* 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) 3 CRTs (0,1 VGA, 0,1,2 for other HDMI) xrandr --verbose VGA1 connected 1280x1024+2560+0 (0x47) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x42 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 ... HDMI1 connected 1280x1024+0+0 (0x47) normal (normal left inverted right x axis y axis) 376mm x 301mm Identifier: 0x43 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 0 1 2 ... HDMI2 connected 1280x1024+1280+0 (0x47) normal (normal left inverted right x axis y axis) 477mm x 268mm Identifier: 0x44 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 2 CRTCs: 0 1 2 Below command fails: xrandr --output VGA1 --auto --output HDMI2 --auto --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Below command passes: xrandr --output VGA1 --auto --output HDMI2 --mode 1280x1024 --rate 60.0 --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Graphic card VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09)

  Read the article

• Why does my webpage look different when I connect using different routers?! Does routers cache files?

  - by Ayyash

  Here is the case, I am working on a site from office and home, I recently updated the stylesheets and logged in the live site from office (using my same laptop I use all the time), and everything looks okay, I come home use my home internet connection to connect to the site using the SAME laptop, the styles are not updated! The thing is: this happens on ALL browsers, and after emptying the cache many times, and even after one month of work, and even if I have never opened the site before on that browser (as if my router has a cache of its own) Another thing: only one particular styles.css file seem to be hanging Extra info: I use the same IP for my home wireless router as that defined in the office, the usual 192.168.0.1

  Read the article

• DRBD as a block device for XEN VM (Centos 5.3)

  - by SaberTooth

  Hi all, I have setup a drbd resource between 2 server nodes - everything works correctly when doing sync tests between the two. (I want to create a HA cluster using drbd,xen and heartbeat) However, when I try and create a XEN VM with Centos as guest operating system, I get through to the partitioning screen on the install but when I select a partitioning type the next screen gives me the following error : "An error has occurred - no valid devices were found on which to create new file systems. Please check your hardware for the cause of this problem." This is the first time attempting create a setup like this and searching Google does not help much... my config files for DRBD and XEN.... DRBD (just the section that is pertinent) on xennode0 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; flexible-meta-disk internal; } on xennode1 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; meta-disk internal; } XEN kernel = "/boot/xeninstall/vmlinuz" ramdisk = "/boot/xeninstall/initrd.img" extra = "text" name = "VM" maxmem = 3000 memory = 3000 vcpus = 4 on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ ] disk = [ "phy:/dev/drbd0,sda1,w", "tap:aio:/srv/xen/xenswap.img,sda2,w" ] vif = [ "mac=00:16:3e:11:67:ae,bridge=xenbr0" ] root = "/dev/sda1 ro" Thanks in advance!

  Read the article

• How do I route traffic to website using a spcified network connection on Windows 7

  - by rwetzeler

  I want to route all traffic to a website over my wireless connection while the rest of the traffic using my lan. What I tried was first finding out the IP address of the website I want to go to. For example, lets say pandora.com. I found it resolves to 208.85.40.20. I have entered that entry into my hosts file. I then added that route using route add 208.85.40.20 mask 255.255.255.255 WirelessIP. It doesn't seem to work however. Instead of using the IP address, is there a way that I can just say.. this URL to route over that connection? Does anyone know of a program that I can install that will do this.. possibly some sort of proxy or a software load balancer that can do this?

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• How does one debug Windows network share authentication?

  - by ajs410

  I have machine0 with 32-bit Vista, logged in as a domain user, running a VMWare image of 32-bit Vista, logged in as a local user, with the VM set to bridge the network. From an administrator account (called admin) within the VM, I try to access the hidden C$ share on machine0 (i.e. start - run - "\\machine0\C$\"). I get no prompts for credentials. Worse, machine0 has an admin account (different password), and machine0\admin gets locked out when VM\admin tries to access the network share. I get a message several seconds later, which feels like a cached credential failure leading to the lockout. I have checked several places for cached credentials; net use, Stored Usernames and Passwords, mapped shares. I rebooted (both machine0 and VM) to make sure the session was clear of any cached credentials. I can force net use to use my domain credentials when accessing machine0, and then I can see the share. I can also see shares that do not require credentials. I decided to try another machine on the network (machine1), 64-bit Vista, local user. This machine has no lockout policy, and after several seconds (feels like failed cached credentials again) it prompts me for credentials. After I enter them, it re-prompts me, saying "logon unsuccessful" (tried my domain credentials, and also machine1\admin's). Which is bogus, because I proceed to log on with remote desktop using the machine1\admin credentials. I have tried this on another machine (machine2, 64-bit Vista), running a copy of the same 32-bit VM, and I don't remember having this problem. machine0 has a fingerprint reader...could that try storing passwords and interfere? Are there any places I'm missing where there could be cached credentials? Is there a way to see what credentials are flying around when I try to connect?

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• High-performance Academic Server [closed]

  - by PHPsmith

  Suppose I want to build a server for the university's academic interests. The server is dedicated only to a site, where users (students and lecturers) just view and fill the academic data. But at a time (e.g. once a semester), about 12,000 students will access the site simultaneously. Due to limitation of resources, I have to build the server using free software (except for the operating system Windows 7, the university has been prepared). The hardware is also limited to the usual 4-core computers (eg, Ivy Bridge Intel Core i7-3770) with approximately 16GB of memory (DDR3 1600 MHz), equipped with an RJ-45 port (Intel 82 579 Gigabit Ethernet). With all these limitations, I have to choose the software (web server, database, etc) are appropriate for this purpose is achieved. I decided to create a site in PHP. Please help me by answering the following questions based on your expertise. (my prime candidate software to consider after googling) Web server which is faster & stable & secure, when implemented and optimized for PHP? And why? (nginx) PHP accelerator which is faster & stable & compatible with the selected web server? And why? (APC with Zend Optimizer+) Database which is faster & stable & secure, when implemented and optimized for selected web server and selected PHP accelerator? (MySQL) Are there any errors that have been or will be happening from my condition is? If there is, please enlighten me? Is there anything else I need to know in order to achieve this goal? If there is, please enlighten me? I understand that the performance also depends on the implementation of source-code program, so I assume it will create a site with the best efficiency (e.g. using AJAX).

  Read the article

• Windows 8 Install Hanging at first white-font boot splash

  - by Omega

  I'm trying to install the Windows 8 preview on my Samsung Series 9 (2012, Ivy Bridge). I've done a bit of a custom scheme with this one: I'm using EFI/UEFI on this system. I've seen no indication that this system supports secure boot (yay!) My SSD is set up with GPT Ubuntu is already installed and working great via UEFI. I'm trying to boot the Windows 8 install from a USB stick via UEFI I don't have access to a CD drive. The problem is that the boot seems to hang at the very first splash screen that looks like this. White windows font, the little beads don't show up. My USB stick has an activity light and it does blink for the first few seconds, but then goes back to it's "nobody is talking to me" idle pulse. What I know: UEFI booting is definitely working. Windows 8 for those few seconds seems to have some kind of access to the USB drive. My Series 9 is running the latest BIOS/firmware. Any idea what I might be able to do to get Windows 8 installed??

  Read the article

• Why are my downloads up to ~1500KByte/sec only, when the ADSL connection locks at 13611Kbit/s?

  - by leladax

  No uploading is going on other than the overhead of downloading which appears to be not high for the abilities of the connection: Only about 30-40KByte/s when the router locks at 1012Kb/s and other direct uploads or uploading overheads can reach more than 100KByte/sec so I don't think it's a congestion at uploading that is doing it. Is there something I miss? Because I assume 13611Kbit/s should be ~1701Kbyte/sec. Is it an overheard at the ADSL level I don't understand? Could it be the ISP doing it? If it's active throttling it can't be on single connections since 2 high speed connections still go up to ~1500KByte/sec. It's not an example on torrents or other complex situations. The tests were on Ethernet, but I doubt the results would be different on wireless. I wonder if the settings of those connections at my end could be doing it, e.g. MTU settings, though I haven't touched the defaults of a common Realtek NIC.

  Read the article

• Connecting to Aerohive AP's from Laptops running Win. 7 using authentication from a Windows 2008 domain server

  - by user264116

  I have deployed a wireless network using Aerohive access points. 2 of them are set up as radius servers. I want my users to be able to use the same user name and password they use when they log onto our domain. They are able to do this from android devices or computers running Windows 8. It will not work on Windows 7 machines. How do I remedy this situation, keeping in mind that the machines are personal machines not company owned and I will have no way to change their hardware or software.

  Read the article

• Broadcasted networks appear cached with netsh? [on hold]

  - by Joe

  We have a company mandate to hide certain windows functions. I'm working on a company application which will allow my users to configure WiFi networks. The app is scanning broadcasted networks using: "netsh wlan show networks" it will return networks that have been turned off. For example: I will run the command and then unplug my wireless router with the SSID "Netgear". For several minutes after turning off the network, the show networks command will continue to return "Netgear". Does anyone know where this gets cached, how to clear it out, or how to force a fresh scan of "netsh wlan show networks"? Thanks all, J

  Read the article

• Windows 7 Natively on Mac OS X Bootcamp, Airport Wifi Unable To Connect

  - by Goober

  I am using a brand new MacBook Pro. I am running a copy of Windows 7 natively via bootcamp (No use of Virtual Machine Software at all). However the only way I can get Windows to connect to the internet is via ethernet, as opposed to the Macs Airport card picking up the wireless. It just refuses to connect, and gives me a limited access status. Any ideas!? I've run Windows XP natively via bootcamp and I had a few issues with the network constantly dropping out, however I blamed that on the drivers and the general shiteness of XP.... Help greatly appreciated.

  Read the article

• Windows 7 Pro x64 suffering from insomnia

  - by gemisigo

  My Win 7 Pro x64 is unable to enter sleep mode. Pressing the sleep button results in strange state where the computer starts entering the sleep mode, the display is turned off but then the whole process stops, it does not switch off the hdd, the keyboard still responds to numlock/capslock, but the display does not on anymore. I have to cut power and restart. If I remove everything (wireless mouse, external hdd, usb hub, etc.) it does enter sleep mode, but if there is something left, it does not, though every one of them has "Allow the computer to turn off this device..." checked and "Allow this device to wake the computer" unchecked. Why does it not work? It was working properly in the RC.

  Read the article

• Setting up Multiple Routers (as Hardware Firewalls) behind a Home Router

  - by Synetech

  I’ve currently got one computer behind a router with built-in firewall functionality, connected to a home cable-modem that has a single Ethernet port and one IP. I’m going to have to set up another computer for the rest of the family to use which of course will need to be connected to the Internet, probably wirelessly since the modem is in my room and the new system would not be. What I would like to do is to get two more small routers with firewall capability and connect each computer to a router, which would in turn connect to the main router which connects to the cable-modem. That way, both systems have a hardware firewall protecting them (particularly the wireless system) and the burden of blocking would be reduced on both the computer CPUs and the main router because the secondary routers would handle some of the workload. I’m trying to find out about the complexities inherent in this design and how I could set it up to work, specifically the IP handling and NAT aspect. Thanks a lot.

  Read the article

• Frequent connection drops when playing online games (StarCraft 2, Battlefield 3) and behind NAT - how to diagnose? [migrated]

  - by Moshev

  I am having some trouble with (I suspect) my wireless router. It's connected to the internet with a regular lan cable and has a static, public IP address. Our two home PCs connect to the router with regular lan cables, plus there's a laptop which connects over wifi. diagram: Internet | | <- isp-supplied cat5 ethernet cable | D-Link D300 ...wifi... laptop / \ / <- cable -> \ PC1 PC2 The PCs and laptop are behind NAT and share the router's public IP. The router is a D-Link D300. PC1 is used for online gaming and I'm experiencing frequent "connection dropped" errors when playing Battlefield 3, StarCraft 2 and the Diablo 3 beta; but not with TeamFortress 2 or the Tribes Ascend beta. The issue goes away when I remove the router and connect PC1 directly to the ISP's cable. I have also tried disconnecting PC2 and the laptop, leaving PC1 as the only machine connected to the router - doesn't help. How can I diagnose what precisely the issue is?

  Read the article

• How to show what proxies/firewalls are enabled on Windows XP?

  - by Stephen Melrose

  Hi, I'm trying to fix a Windows XP PC that is having a strange problem. The computer can't seem to connect to the internet, even though an internet connection is present. The router and internet is working fine as I've connected a laptop to it via LAN and wireless and both worked fine. The PC in question is connected to the router as it has an IP from the DHCP. The problem is I can't connect to nor ping any internet address from the PC. I can't even connect to the router admin itself. I've tried both LAN ports in the PC, same problem and both. I'm assuming there's a proxy or firewall on the PC stopping the connections, I just don't know how to find them or see which one is causing the issue. So my question is how do I on Windows XP display the system proxy settings and/or any firewalls that are running? Cheers.

  Read the article

• KVM virtual machine unable to access internet

  - by peachykeen

  I have KVM set up to run a virtual machine (Windows Home Server 2011 acting as a build agent) on a dedicated server (CentOS 6.3). Recently, I ran updates on the host, and the virtual machine is now unable to connect to the internet. The virtual network is running through NAT, the host has an interface (eth0:0) set up with a static IP (virt-manager shows the network and its IP correctly), and all connections to that IP should be sent to the guest. The host and guest can ping one another, but the guest cannot ping anything above the host, nor can I ping the guest from anywhere else (I can ping the host). Results from the guest to another server under my control and from an external system to the guest both return "Destination port unreachable". Running tcpdump on the host and destination shows the host replying to the ping, but the destination never sees it (it doesn't even look like the host is bothering to send it on at all, which leads me to suspect iptables). The ping output matches that, listing replies from 192.168.100.1. The guest can resolve DNS, however, which I find rather odd. The guest's network settings (connection TCP/IPv4 properties) are set up with a static local IP (192.168.100.128), mask of 255.255.255.0, and gateway and DNS at 192.168.100.1. When originally setting up the vm/net, I had set up some iptables rules to enable bridging, but after my hosting company complained about the bridge, I set up a new virtual net using NAT and believe I removed all the rules. The VM's network was working perfectly fine for the last few months, until yesterday. I haven't heard anything from the hosting company, didn't change anything on the guest, so as far as I know, nothing else has changed (unfortunately the list of packages updated has since fallen off scrollback and I didn't note it down).

  Read the article

• How can I tell if my ISP is redirecting my DNS queries?

  - by Nack

  I've attempted to use some DNS services like OpenDNS, and no matter what I do the DNS queries don't return the expected results. Watching the packet traffic on my firewall, I can see the queries go out to the intended DNS server address and responses coming back, but the results are not as expected, for example, the OpenDNS test page always fails even though the requests appear to be going to their servers. I suspect my ISP is intercepting DNS queries and sending them to their own servers. Is there a way to verify this? Is there something else I might be missing? I'm using 3G wireless service from Sprint.

  Read the article

• Cross subnet connection [closed]

  - by user30472

  My internal Windows 2008 AD network is 172.20.xxx.xxx My Apple Wireless base stations only allows DHCP 172.16.xxx.xxx Private IP address ranges: 10.0.0.0 to 10.255.255.255 172.16.0.0 to 172.31.255.255 192.168.0.0 to 192.168.255.255 The problem: The internet works from my IPad that has a 172.16.xxx.xxx address, but I can't access (browse) my tools server that is 172.20.xxx.xxx that host my Filemaker database. Is it possible to add 172.16.xxx.xxx range somewhere in DHCP or DNS on my Windows domain server so I can access tools? Or is there another way to make this connection work? Thanks

  Read the article

• Win XP cannot connect (or see) my wifi network, but can see others

  - by Jorre

  since yesterday I have a strange wifi problem with my pc. I have a wireless linksys router setup that worked fine for many months, now since yesterday my pc won't connect to the wifi signal anymore. The strange thing is, my macbook pro still connects fine. SSID is broadcasting, but my windows XP doens't see it, I have all signal modes set to "auto". Windows XP sees all my neighbours wifi networks, so the wifi card isn't broken or anything. Any idea what can be wrong here?

  Read the article

• Trying to communicate between virtual servers on the same host through ipv6

  - by Daniele Testa

  I am running KVM on a host with 2 virtual servers. Each virtual server has a own bridge interface on the host VPS1 has br1 VPS2 has br2 Each virtual server has a own ipv4 and a ipv6. The virtual servers has no problem communicating with internet or with eachother through ipv4. However, with ipv6, they can only communicate with internet and NOT with eachother. The host can ping the 2 virtual servers without any problems, but they cannot ping eachother. iptables has been set to ACCEPT on all chains, so it is not the problem. VPS1 has ipv6 = 2a01:4f8:xxx:xxx::10 VPS2 has ipv6 = 2a01:4f8:xxx:xxx::5 the host has the following routes set: ip route add 2a01:4f8:xxx:xxx::10 dev br1 ip route add 2a01:4f8:xxx:xxx::5 dev br2 When I do a ping from VPS2 to VPS1, I see the following on the host: tcpdump -i br1 15:32:27.704404 IP6 2a01:4f8:xxx:xxx::10 > ff02::1:ff00:5: ICMP6, neighbor solicitation, who has 2a01:4f8:xxx:xxx::5, length 32 So it seems like the host is seeing the request coming from VPS1 on br1. But for some reason, it does not forward it to br2. Instead it is asking where the destination IP is through ipv6 multicast. Anyone has a clue what is going on? I find this very strange, as it is working fine with ipv4 with the exact same settings and routes.

  Read the article

• Is it possible to use the bluetooth adapter from my logitech keyboard to connect headset?

  - by King Chan

  So, as titled. I have a bluetooth wireless keyboard that goes with the bluetooth adapter from Logitech 2 years ago. Recently I just brought a bluetooth headset from other company, but I wonder if I can reuse the bluetooth adapter from Logitech to use the headset? I don't seems to find an option in my control panel that allows me to add the headset device.... Or the blue adapter that comes with Logitech is only able to connect to the logitech keyboard? In that case, if I buy a bluetooth adapter, will it possible to share 1 bluetooth adapter with two device? (1 to 2? not 1 to 1?)

  Read the article

• Cross subnet connection

  - by user30472

  My internal Windows 2008 AD network is 172.20.xxx.xxx My Apple Wireless base stations only allows DHCP 172.16.xxx.xxx Private IP address ranges: 10.0.0.0 to 10.255.255.255 172.16.0.0 to 172.31.255.255 192.168.0.0 to 192.168.255.255 The problem: The internet works from my IPad that has a 172.16.xxx.xxx address, but I can't access (browse) my tools server that is 172.20.xxx.xxx that host my Filemaker database. Is it possible to add 172.16.xxx.xxx range somewhere in DHCP or DNS on my Windows domain server so I can access tools? Or is there another way to make this connection work? Thanks

  Read the article

• How do I make my play/pause keyboard button work correctly in iTunes 10 on Windows?

  - by EvilChookie

  First and foremost, I have mmKeys installed correctly. My iTunes works almost perfect while minimized to the tray. My problem is with the play/pause button on my Wireless Comfort Keyboard 5000. When iTunes does not have focus (like it's minimized, or if it isn't the application I'm active in, like right now while typing this) the play pause button toggles twice. So, I'll push the pause button - and the song that is playing will pause, but a split second later will start up again. If the song is paused, and I push play, the song will immediately pause again. In order to get the key to work correctly, I must give iTunes focus, and then push the button. Here's a video I created on youtube: http://www.youtube.com/watch?v=POh6Gbm5QZI OS: Windows 7 x64 iTunes: 10.0.0.68 Intellitype: 8.0 Edit: Apparently I have intellitype 8.0 instead of 7.1

  Read the article

< Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >