Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 183/286 | < Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >

• Tomato OS: "memory exhausted" running vi .... how to solve?

  - by Sam Jones

  I have set up tomato (shibby) on an asus RT-N66U router. It works great. I loaded up a few pieces, like transmission and optware. I can run vi, but when I run vi it fails with a "memory exhausted" error, and the terminal session hangs. For reference: If I simply start "vi" it runs fine. But if I specify vi I get the memory exhausted error, even if the file I am opening is just a couple of hundred bytes in size (like fstab). I discovered that my swap partition was not properly set up, so I did that. The swapon command now indicates I really do have a swap: [root@MyRouter samba]$ swapon -s Filename Type Size Used Priority /dev/sda1 partition 32900860 0 1 How can I get vi to work? Thanks! System setup reference information: asus RT-N66U router 2TB usb hard drive partitions on hard drive: Disk /dev/sda: 2000.4 GB, 2000398839808 bytes 255 heads, 63 sectors/track, 30400 cylinders Units = cylinders of 16065 * 4096 = 65802240 bytes Disk identifier: 0xfacbc8ab Device Boot Start End Blocks Id System /dev/sda1 1 512 32900868 82 Linux swap / Solaris /dev/sda2 513 29000 1830638880 83 Linux running samba memory: $ cat /proc/meminfo MemTotal: 255840 kB MemFree: 210980 kB Buffers: 5264 kB Cached: 22768 kB SwapCached: 0 kB Active: 20272 kB Inactive: 11448 kB HighTotal: 131072 kB HighFree: 99868 kB LowTotal: 124768 kB LowFree: 111112 kB SwapTotal: 32900860 kB SwapFree: 32900860 kB Dirty: 0 kB Writeback: 0 kB TIA!

  Read the article

• What's the best way to telnet from a remote Windows PC without using RDP?

  - by Rob D.

  Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

  Read the article

• Rebooting access point via SSH with pexpect... hangs. Any ideas?

  - by MiniQuark

  When I want to reboot my D-Link DWL-3200-AP access point from my bash shell, I connect to the AP using ssh and I just type reboot in the CLI interface. After about 30 seconds, the AP is rebooted: # ssh [email protected] [email protected]'s password: ******** Welcome to Wireless SSH Console!! ['help' or '?' to see commands] Wireless Driver Rev 4.0.0.167 D-Link Access Point wlan1 -> reboot Sound's great? Well unfortunately the ssh client process never exits, for some reason (maybe the AP kills the ssh server a bit too fast, I don't know). My ssh client process is completely blocked (even if I wait for several minutes, nothing happens). I always have to wait for the AP to reboot, then open another shell, find the ssh client process ID (using ps aux | grep ssh) then kill the ssh process using kill <pid>. That's quite annoying. So I decided to write a python script to reboot the AP. The script connects to the AP's CLI interface via ssh, using python-pexpect, and it tries to launch the "reboot" command. Here's what the script looks like: #!/usr/bin/python # usage: python reboot_ap.py {host} {user} {password} import pexpect import sys import time command = "ssh %(user)s@%(host)s"%{"user":sys.argv[2], "host":sys.argv[1]} session = pexpect.spawn(command, timeout=30) # start ssh process response = session.expect(r"password:") # wait for password prompt session.sendline(sys.argv[3]) # send password session.expect(" -> ") # wait for D-Link CLI prompt session.sendline("reboot") # send the reboot command time.sleep(60) # make sure the reboot has time to actually take place session.close(force=True) # kill the ssh process The script connects properly to the AP (I tried running some other commands than reboot, they work fine), it sends the reboot command, waits for one minute, then kills the ssh process. The problem is: this time, the AP never reboots! I have no idea why. Any solution, anyone?

  Read the article

• Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

  - by MasterRoot24

  I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

  Read the article

• Win Server 2k and Win 7 client

  - by Ray Kruse

  I have a Win Server 2000 system with AD configured. The network consists of an OKI printer, a network server, a wifi router a Win 2k client and the server. I'm trying to connect a Win 7 client. The purpose of the network, besides sharing equipment is to move files from client to client and scatter backups over more than 1 machine. The Win 7 client is configured for DHCP and does in fact receive it's IP and DNS configuration from the server and it sees the printer, wifi router and network drive, but does not see the Win 2k client nor the Win 2k server. I have tried the LAN Management Authentication Level set to 'Send LM & NTLM responses' with the 128 bit encryption removed. I've also done the registry hack on the key 'LmCompatibilityLevel'. Neither of these have helped. I have two questions: Is there a fix or is Win 2k totally incompatible? Is the best (or quickest/cheapest) fix to upgrade the server to Win 2k3 and not worry about the Win 2k client? Thanks for any help. Ray Kruse Buffalo, KY

  Read the article

• Can I run a mix of static addressing and NAT?

  - by aroth

  Let's say that an ISP offers a plan with 5 static IP addresses, but I have more than 5 devices, many of which (such as a networked printer, for instance) I do not want or need to have a static IP address. So the topography I'm planning goes something like: ISP -> Router -> Switch -> Computer (static address) -> Computer (static address) -> Printer (DHCP/NAT) -> Tv (DHCP/NAT) -> (...) -> Wireless Devices (DHCP/NAT) Generally speaking, is it possible to run a network like that? If not, then what sort of setup do I need so that I can assign static addresses just to the things that need them, and use DHCP/NAT for everything else? Also, what internal networking devices will consume a static IP address? I'm pretty sure the router will, correct? Does the switch also?

  Read the article

• Network Traffic Log

  - by Chris Becke

  Background - On my "home" network I have a Linksys WTR45GL router providing my internet access as well as a wireless AP. Connected I have * 2 Windows PCs (wired) * At least one laptop (Wired) * Some 802.11 enabled handheld consoles (PSPs) * A Nintendo Wii * Some windows XP pcs used by the people in the granny flat. Where I live, South Africa, well, 1Gb worth of monthly cap is, while not expensive, costly enough that I'd like to be sure that all the bandwidth used by devices on my network is ... well ... legitimate and not the result of neighbors parasiting my wireless, malware or just the result of "liberal" download policies in my software. I got the Linksys WRT45GL on the understanding that there were custom firmwares (DD-WRT and Tomato) that allowed bandwidth tracking, but there doesn't seem to be any facility to get a log of traffic that can be examined to see (a) which local devices were the biggest consumers of bandwidth and (b) what they were connected to. What tools are there for logging traffic such that, when it gets to that OMG moment in the month when all my bandwidth is gone, I have a chance to find out what the hell used it all up (and hopefully attempt some corrective action).

  Read the article

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• LAN network (switch?)

  - by guywhoneedsahand

  I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• What is the correct iptables rule when NATing multiple private subnets?

  - by Jose Mendez

  I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

  Read the article

• Linux Port 80 to redirect to a Windows box

  - by Richard Staehler

  I have 2 servers here at work. One is a Windows 2008 Server R2 (for safety's sake, lets use 192.168.1.100) and the other is a Fedora 14 (192.168.1.101). Currently when you hit our subdomain, x.test.com, our routers tell it to go to our Fedora box, and since Apache is installed and listening to port 80, it displays the Fedora Apache Test Page. It's obvious that I don't use port 80 for this machine, however I do use NAGIOS on it and its always nice to be able to access that from anywhere in the world. So when I want to access it, I just type x.test.com/nagios. Now here comes the dilemma.... On the Windows R2 box, we recently have installed a program that requires us to setup a web server using IIS7. Because of this application, I'm going to be creating a new subdomain called y.test.com, but since we only have 1 WAN/router, it will still get pointed to our Fedora box. That being said, it wants to use port 80 as well (or whatever port I damn well wish to assign it). So my question is: since our router is pointing to the Fedora 14 box (.101), and I want to make sure I can access NAGIOS from anywhere in the world, how do I tell Apache (httpd) to redirect port 80 to the other server (.100)? If not possible, what are my other options? I have rinetd installed on Fedora and have even tried the option 192.168.1.101 80 192.168.1.100 80 and it didn't seem to work "because port 80 was already bound" Thoughts? and Thanks!

  Read the article

• Internet connection & IIS stopped on windows xp after VMware server 2 installation

  - by Eduardo Xavier

  Hi, I'm running a local network. My IP ranges from 192.168.1.2 to 192.168.1.15. All IP are static ones. And my router's IP is 192.168.1.1 and I provide it as default gateway and preferred DNS server on client machines. Everything worked fine on this scenario. I could use internet and reach services on other machines. BUT I have installed VMware server 2 on the windows XP to host windows 2003 Virtual Machine (VM). I set the following configuration: Windows XP's => 192.168.1.11. Windows 2003 => 192.168.1.12. (virtual machine) This approach worked just fine as it used to work with Microsoft Virtual PC. I can access mysql & IIS websites on the windows 2003 virtual machine. BUT two things doesn't work anymore on the Windows XP: internet connection - but I can see the MAC address on the wireless router IIS - Ping on 127.0.0.1 it's ok as I can hit localhost:8222 nor localhost Does anyone knows how to fix any of this? (at least the internet connection)

  Read the article

• Two NIC's 2 Internet Connections, 1 Windows Server 2008 RC2, Routing help required

  - by PJZ

  Hello, I have a Windows 2008 server and 4 other client machines on my home network. I have two internet connections. The main connection is setup with a home router and DHCP on that for all the clients on the network. The secondary connection is just a cable modem which is plugged directly into the server. Local Area Connection: This NIC has an external IP and is connected to the Cable Modem. Local Area Connection 2: This NIC has an internal IP (192.168.0.102) and allows access to all the internal computers. It also has internet access via the local router. So here lies the problem, I want to use the Cable connection on the server for the internet traffic (so that the traffic for server/clients are seperated) but I also need to maintain local access. I am wondering how to make it so that all the internet traffic goes via that NIC because at the moment it goes through the local NIC. As a secondary problem I would also like to forward the connection of one application used by the clients via the server and the cable/server internet because of poor routing for it on the main connection. This perhaps is something for another question though. Thanks for any help you can offer me. Regards PJ

  Read the article

• OS X can't copy files from Windows Home Server...over wifi.

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks!

  Read the article

• Acer Aspire one is falling apart on Ubuntu

  - by Narcolapser

  Question: How do I have my netbook detect and install hardware? Info: I have an Acer Aspire One, it came with windows XP and I loaded it with Win7. I decided I wanted to change to Ubuntu so I tried Ubuntu netbook remix, which failed horribly, and so after attempting 3 or so other OS's I ended with Ubuntu Desktop 9.10. Which worked fine for a while, but there were some minor issues so I asked a question about it here and decided to change my OS again. This last weekend I tried mandriva like that guy in my other question suggested, no success. when I had though my netbook lost the ability to use it's touch pad, I didn't think much of it, just thought it must be a driver or something. But When Mandriva failed, and I also while I was at it tried Damn small linux and Debian, which both failed to, I decided to switch back to Ubuntu Desktop(some where in here my keyboard stopped working for one attempt to). But first I gave the netbook remix one more try. it worked this time, with the exception of it didn't have any networking. I thought it was a driver issue again and finished the weekend with ubuntu desktop 9.10 again. But now things get really crazy. it doesn't know it has a wireless card or an ethernet card. It doesn't know my phone is connected trying to provide wireless broadband either. I'm clueless on what could be the problem. And with only a minimal amount of experience with Ubuntu can't navigate the entire interface with only my keyboard(it doesn't detect a USB mouse when I plug it in, it had when I installed it. in fact the network interfaces were working just fine when I live boot ubuntu to installed it). Even so, I don't know where to go or what to do to make it recognize it's hardware. I'm in a dire situation, any help is welcome.

  Read the article

• unable to ping hostname, but \\hostname\\c$ works!?

  - by ciscokid

  I'm having a strange issue on my initial lab setup. Situation: Host with OS Server 2008 R2 64bit, on this host a Virtual Machine in Hyper-V with OS Server 2008 SP1 32bit. The virtual machine has a fixed ip, and is referring to itself for the preferred DNS Server (dns server role has been installed). The host has tcp/ip set to automatic (so automatic ip from router, and dns/gateway = router). Both are able to ping each other on IP address (same ip range). Both are NOT able to ping each other on hostname (sounds logic because virtual machine dns server does not yet have a dns record for the hostmachine). But here's the strange thing: I am able to set up a working network mapping on the Virtual Machine to the host: \hostname\c$. The first thing I thougt was 'something' is blocking the ping request, so I completely disabled Windows Firewall on both Virtual Machine and host. Still pinging on hostname in both ways didn't work, yet I am able to access the network mapping on hostname. There is no extra software installed on both systems (clean windows server 2008).Can someone tell me what is causing this? I always thought: ping on IP address works = network mapping on IP address works. Pinging on hostname doesn't work = network mapping on hostname doesn't work neither. Where am I wrong? Looking forward to your advice!

  Read the article

• I can't connect new Windows 7 PC to Mac iBook with OS 10.3.9

  - by Jeff Humm

  Help ! I have an old iBook wired to a router and a new PC linking wirelessly to same router. On the Mac I have 'seen' the PC but not been able to connect to it. On the PC, the Network and Sharing Centre lists 'IBOOK'. When I click on this, 'Windows Security' asks me to 'Enter Network Password', asking for User name and password. I have tried: 1) The user name and password of my admin account on the iBook. This returns a 'logon failure' message but lists the user name as [NAME_OF_PC\User Name], suggesting it was looking for the user name of the PC, not the Mac. 2) The user name and password of my account on the PC. This also returns a 'logon failure' message. 3) The user name of my account on the PC and the 'homegroup password' given to me by Windows when setting up the PC. This also returns a 'logon failure' message. Today I've tried connecting the two machines via a patch cable - still no joy. Can anyone help? It is 20 years since I wrestled with any OS other than Mac, and 10 years since I've done mich wrangling with the Macs, so please assume no knowledge! Thanks in advance,

  Read the article

• Fast Ethernet module for Cisco 2620

  - by Kenny Rasschaert

  I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

  Read the article

• SFTP only works occasionally

  - by 82din

  I suddenly get this error using SFTP: Status: Connecting to example.com... Response: fzSftp started Command: open "[email protected]" 22 Command: Pass: ********* Status: Connected to example.com Status: Retrieving directory listing... Command: pwd Response: Current directory is: "/root" Command: ls Status: Listing directory /root Error: Connection timed out Error: Failed to retrieve directory listing I tried using FileZila, Cyberduck, Shell (Terminal), same result. However, it worked fine today (just a few seconds) in Passive mode. I guess something changed in my network, so I have tried both: Active and Passive mode: Connecting to probe.filezilla-project.org Response: 220 FZ router and firewall tester ready USER FileZilla Response: 331 Give any password. PASS 3.6.0.2 Response: 230 logged on. Checking for correct external IP address Retrieving external IP address from http://checkip.dyndns.org:8245/ Checking for correct external IP address IP <external IP> big-bf-ccc-f Response: 200 OK PREP 49565 Response: 200 Using port 49565, data token 380352881 PORT 186,15,222,5,193,157 Response: 200 PORT command successful LIST Response: 150 opening data connection Response: 503 Failure of data connection. Server sent unexpected reply. Connection closed Because I'm working behind a router, I get my external IP from http://checkip.dyndns.org:8245/ I also tested different range of ports.

  Read the article

• samba share not on network after upgrading to Ubuntu 12.04LTS. [migrated]

  - by Sylvain Huard

  I just upgraded an old Ubuntu box to 12.04LTS (machine named A-Ubuntu). This is an upgrade not a format re-install. All the accounts and config were preserved. The basic setup is a local network with 2 Ubuntu machines (let say A-Ubuntu, B-Ubuntu) and a MAC (C-MAC). Before the upgrade, all of them could see each other by their names not only the IP address. The local network has a D-Link Router where everybody is connected with RJ-45 wired etherenet (not wi-fi). Since the A-Ubuntu upgrade, we can't see this machine name on the Network and its name is not on machine list in the D-Link router anymore. We can see it's IP address only. I can't access A-Ubuntu from the other two by its name but I can ping it with its address (192.168.0.109). From A-Ubuntu, I can connect and see the shared samba folders on B-Ubuntu and C-MAC. But from B-Ubuntu and C-MAc, I can't connect to A-Ubuntu. Correct me if I'm wrong but this tells me that Samba should be fine and the real problem is that A-Ubuntu does not advertise its name on the Network so the D-Link does not have it in its table so nobody else finds it. After a lot of googling, I see that it is the job of avahi and mdns to do so. Those packages are running, I checked multiple config files for samba, avahi, mdns to see as if it is like the examples on the WEB and also similar to what I find on the working B-Ubuntu machine. This is the same. I did multiple service restart with samba, avahi, remove the firewall to make sure it does not block the hostname broadcast. I rebooted multiple time to make sure the update I was making were effective. Still, Can't see the A-Ubuntu name on the network. Any idea what it can be?, Where to look next?

  Read the article

• NATing IPv4 while routing IPv6

  - by Hugo

  I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

  Read the article

• Cooling Server Closet - No A/C Is Possible

  - by JamesCo

  We're moving into a new office in an old building in London (that's England :) and are walling off a 2m x 1.3m area where the router & telephone equipment currently terminates to use as a server closet. The closet will contain: 2 24-port switches 1 router 1 VSDL modem 1 Dell desktop 1 4-bay NAS 1 HP micro-server 1 UPS Miscellaneous minor telephony boxes. There is no central A/C in the office and there never will be. We can install ducting to the outside quite easily - it's only a couple of metres to the windows, which face a courtyard. My question is whether installing an extractor fan with ducting to the window should be sufficient for cooling? Would an intake fan and intake duct (from the window, too) be required? We don't want to leave a gap in the closet door as that'll let noise out into the office. If we don't have to put a portable A/C unit into the closet, that'd be perfect. The office has about 12 people; London is temperate, average maximum in August is 31 Celsius, 25 Celsius is more typical. The same equipment runs fine in our current office (same building as new office, also no A/C) but it isn't in an enclosed space. I can see us putting say one Dell 2950 tower server into the closet, but no more than that. So, sustained power consumption in the closet would currently be about 800w (I'm guessing); possibly in the future 2kw. The closet will have a ceiling and no windows and be well-insulated. We don't care if the equipment runs hot, so long as it runs and we don't hear it.

  Read the article

• Vyatta masquerade out bridge interface

  - by miquella

  We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

  Read the article

• Network share not always available on Windows 2003

  - by JP Hellemons

  Hello everybody, we have a windows 2003 server with a shared directory/folder. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the problem occurss when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in the same LAN. the internet connection is really stable, so it's really strange. because a stable internet connection should imply that the local network connection is also stable and that this is a windows issue. can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none. EDIT: can this be related to mapping a shared directory to a drive letter? and that there is a router between me and the mapped network drive? or is it just windows that is not working well with two users on the same shared folder? should I install samba or something?

  Read the article

< Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >